Search Documents

By McDougall I, Claoue-Long J

A combination of high precision 40Ar/39Ar and U-Pb dating has been used to determine the age of hydrothermal minerals and host rocks in a number of Lachlan Fold Belt (LFB) gold deposits in New South Wales, Au4 ralii In particular, this investigation demonstrates that the UAr/ Ar technique of K-Ar dating can be used to determine the timing of mineralization in Palaeozoic systems.A close temporal link between mineralization and Late Ordovician to Early Silurian magmatism is indicated by the dating work. Hydrothermal sericite from the Goonumbla p8rph gy Cu deposit and Glendale Au prospect yieldsAt/ Ar step heating ages between 437.9 ¦ 1.1 and 441.2 ¦ 1.1 Ma (16), and4 minjrnum age of about 425 Ma has been obtained by Ar/ Ar dating of hydrothermal amphibole from the Browns Creek Au-Cu skarn deposit. Hydrothermal aluniI8 frog the Gidginbung epithermal Au deposit yields reset 44 Ar/ Ar ages of 401.0 ¦ 1.3 to 417.3 ¦ 1.3 Ma (16). U-Pb dating by ion microprobe on magmatic zircons from the vicinity of the Goonumbla and Gidginbung deposits gives ages of 438 ¦ 3.5 Ma (2 6), and 435 ¦ 2.5 Ma (2 (7) respectimly, W a minimum age of 435 Ma has been obtained by Ar/ Ar dating of magmatic phases from volcanic rocks adjacent to the Browns Creek skarn deposit. Magmatic episodes near the Sheahan-Grants gold skarnpost give ages of 479.2 ¦ 1.1 and 467.9 ¦ 4o1 by 'Ar/ 9Ar dating of magmatic amphibole. Most Ar/3yAr age spectra show the effects of partial Ar loss at between 360-420 Ma, probably due to heating caused by granitoid emplacement.The radiometric dating work in this paper suggests a restricted metallogenic epoch in the Late Ordovician-Early Silurian LFB, NSW, of similar duration to that found in the Andean margin and the western Pacific island arcs around the Pacific Rini.

Jan 1, 1990

By B Olsson, C Glassock

Computer simulation modelling (discrete event) has been used at Olympic Dam (OD) to model the handling of ore from the point of extraction at the stope drawpoint through to the ore stockpile on the surface. Computer simulation is a well accepted tool for modelling the behaviour of such large and complex operating systems. It is a particularly useful technique in complex operations where there are multiple interactions between the inputs and outputs of various unit operations. In this instance it can be utilised during the early stages of a project, for example, as part of the business case definition phase or the early engineering phase. A well constructed and tested simulation model provides a sound base upon which informed business decisions can be made. Furthermore, the behaviour of the model with varying inputs can help build a solid understanding of how the asset behaves when varying inputs and constraints are imposed upon it and, as a result, the major points of leverage that designers and operations personnel have to affect the real world behaviour of those assets. Better decisions can be made when the right facts can be examined, various options explored and conclusions tested. Simulation modelling is one of the tools available to make this process work.

Jan 1, 2005

By Harada M, Katsuta S

In order to shorten the time taken to com- plete shield tunnel excavation work, reduce labor costs and to improve safety, an automatic assembly robot system for the segments used has been developed. It was developed in the three years from 1982 until 1984. An experimental assembly system for concrete segments (outer diameter:.3.55m) has been thoroughly tested to confirm that these segments can be fed and assembled automatically (Fig. 1, 2). This report outlines the robot which will be put into practical use in the near future. The robot senses the position of already assem- bled segments by means of position sensors, controls the position and the attitude of the segment to be assembled to allow bolt hole positioning, and completes the automatic assembly of a se;nent by automatically tighten- ing bolts. The six segments which make up one ring can be automatically assembled in about 25 minutes.

Jan 1, 1987

By Hammond J. R, Ward T. A

The Tom Price orebody, in the Hamersley Ranges of North West of Western Australia, is mined by Hamersley Iron Pty. Limited. The orebody is a folded sequence of hematite and shale bands capped with goethite, with a con- sequential variable iron content. The overall grade is below that required to yield spec- ification product, necessitating selective mining, 'Zone Plans' based on geological structure have been developed to yield forward information on material types and grades. Short and medium term mine plans - the initial stage of quality control - are based upon these 'zone plans'. Blasts are laid out to break to the grade boundaries, thus minimising dilution, and the samples taken from the blasthole cuttings provide blast grades. Blending of shovel out- put from different blasts forms the operational basis of grade control. Shales, being more friable than hematite, produce fines that are lower in iron grade than lump. Quality control in the mine centres around maintaining the target fines grade, compensation being applied in the mine if the fines grade lies outside the target range.

Jan 1, 1973

General Gold was discovered in quartz veins at Wiluna in 1896, and the first lode was discovered in 1904. Since 1896, some 2.5 million ounces of gold have been produced from the Wiluna area. The mining operations at Wiluna are 100 per cent owned by Wiluna Gold Pty Ltd, a wholly owned subsidiary of Wiluna Mines Ltd. Oxide and sulphide gold ore is extracted by conventional open pit mining techniques, and ran-of-mine ore is processed through two separate circuits. The oxide circuit has a capacity to treat 600 0(X) tonnes per annum and the sulphide circuit has a capacity to treat 400 (XX) tonnes per annum. Additional gold is won by dump leaching sub-grade oxidised ore and by retreating of primary ore flotation tailings from previous operations. Testwork carried out in 1990 indicated the viability of leaching dumps of run-of-mine oxide ore, and in June 1991 Signet Engineering of Perth, WA, was awarded an EPCM contract to construct a nominal 2.5 million tonne dump leach facility, for a total construction estimate of 51.75 million.

Jan 1, 1994

This paper outlines the advances made in vacuum filtration as developed by Outomec Process Filters and details the results obtained at a number of Australian installations. The first section of the paper details the technical advances made by the use of ceramic media in vacuum filtration and explains the reasons for the use of the technology. The second part of the paper discusses a number of Australian installations of the ceramic vacuum filter and where possible compares the actual experiences with those predicted from the test work which preceded the installations. The Ceramec Capillary Vacuum Filter is a vacuum disc filter which combines the proven mechanical attributes of a disc filter with exciting new ceramic vacuum technology from Outomec of Finland.

Jan 1, 1991

A novel fracture-plane control blasting technique with particular application in wall-control blasts in mines employing medium to large diameter boreholes is described. It consists of a string of nested holes, each nest consisting of a large diameter charge-hole flanked on either side by a small diameter satellite hole. Each nest is shown to be an analog of a pressurized hole with diametral notches along its length. This 'equivalent-notched' hole concept for generating controlled fractures along preferred directions has been successfully investigated in the laboratory and in the field. The technique has been used to generate controlled fractures on a quarry bench in highly jointed limestone. The resulting blasts with a 250 mm diameter central charge-hole and 50-75 mm satellite holes show that two nests of such holes almost 5 m apart could be joined by a single co-linear fracture. The design range of diameter ratio between charge-hole and satellite hole is 3 to 6 and spacing is 3 to 5 charge-hole radii. With careful matching of explosives and decoupling, and combination of diameter ratio and spacing, it would be possible to connect two nests of such holes more than 20 charge diameters apart by a single controlled fracture plane. The relative merits of the technique against existing wall-control blasts are discussed, and guidelines for practical fracture-plane control blast designs are discussed.

Jan 1, 1990

By Jena, Anand S, Das R. P

Leaching studies were carried out on Indian Ocean manganese nodules using sulphuric acid as the lixiviant. By leaching the nodules with 8 per cent sulphuric acid for 12h at 100°C, copper and nickel could be completely extracted along with 50 per cent cobalt and 6.2 per cent manganese.94.2 per cent of the iron was also dissolved. To increase manganese and cobalt extraction, charcoal was used as a reductant. The role of charcoal was to reduce the manganese dioxide and render it soluble as manganese sulphate as well as to facilitate solution of the cobalt minerals associated with the manganese dioxide. Various leaching parameters were studied including acid concentration, amount of reductant, leach time, pulp density and leach temperature. It was found that by leaching the nodules with 10 per cent sulphuric acid at 100°C for 4h using 5 wt/wt per cent charcoal (0.05g of charcoal per g of nodule) almost complete extraction of copper, nickel, cobalt and manganese could be achieved. However, under these conditions all the iron present in the nodules was also leached.

Jan 1, 1989

By M Lovitt, T Hewitt

The extraction of drawbells in Lift #2 at Northparkes Mines E26 orebody was achieved by single shot blasting, enabled through the use of electronic detonators. This paper discusses the designs considered at the time of the feasibility study and the various changes made to these designs prior to and during the construction phase of the Lift #2 block cave. Operational issues encountered are highlighted, as are ways in which these were overcome. The amount of personnel utilised to mine the drawbells is also covered. Lists of design and operational considerations to be used for drawbell extractions have been included.

Jan 1, 2005

By Fulton B, Stewart R, Leach T

Gold mineralisation at Porgera is inferred to have been derived from a deep differentiated magmatic source which is capped by a series of (now tilted) inward dipping sills and stocks, which comprise the Porgera Intrusive Complex. An arc normal transfer structure provides a conduit, at the intersection with an arc parallel structure, into which basic magma derived from the deep melting of mantle material has been emplaced. Two phases of mineralisation display an association with late stage feldspar porphyry intrusives. Stage I carbonate-base metal-style gold mineralisation occurs as early quartz-sericite, then massive sulphide and late zoned Mn-Fe-Mg-Ca carbonate vein/breccias. Magmatic fluids derived from the deep magma source, are interpreted to have migrated along the margin of a feeder stock to the sills, and south to Waruwari. Stage II epithermal Au-Ag quartz-style gold mineralisation occurs as early fluidised breccias and carbonate veining, followed by zoned quartz-roscoelite-carbonate-gold vein/breccias, and late carbonate and/or sulphate open space infill. Magmatic fluids are interpreted to have utilised the same plumbing system as the late stage feldspar porphyry intrusive, and then migrated into the Roamane Fault which was dilated by; dextral rotation on elements of the transfer structure, normal faulting, and refraction around the competent footwall hornblende diorite. Bonanza gold is localised in a jog in the Roamane Fault, hangingwall splits and at intersections with cross structures. Bulk low grade Stage I gold has been deposited by the mixing of magmatic fluids with cool gas condensate waters, whereas high grade Stage II gold mineralisation resulted from the rapid quenching of mineralised magmatic fluids by oxygenated groundwaters.

Jan 1, 1995

Three key areas of C.I.P. plant design, viz. leach- ing time, adsorption and the gold loading on the carbon, are discussed and illustrated with examples. The need for accurate pilot plant data for use in assessing and optimising design is emphasized. This approach should minimize capital and maximise return on capital. It is demonstrated that, as regards adsorption, economics favours short retention time, high gold loadings and mechanically agitated, draft tube reactors. INTRODUCTION Little attempt appears to have been made in Australia to design the present generation of C.I.P. plants to achieve an economic optimum. Most would, seem to have been based on pre- liminary leaching data, gold extraction and value and rule of thumb which, in general, has led to over design and over capitalisation. An essential step to effective economic design is a comprehensive pilot plant study to establish definitive operating parameters, yields and reagent costs. In most cases the cost of developing this data will be more than offset against capital savings in plant; the operating profit should be increased substantially, and profit is maximised for known

Jan 1, 1982

INCREASE OF CATASTROPHE FREQUENCY AND SEVERITYIn the last couple of decades the frequency of natural catastrophes has increased dramatically. This realization results from the statistical analysis of the comprehensive loss data that we have been collecting constantly over the last 30 years and have evaluated in connec-tion with the preparation of our "World Map of Natural Hazards", which is now in its second edition (Munich Re, 1988). Each month brings data on between 30 and 50 new loss events. Fortunately, however, only a few of these have to be added to the list of major natural catastrophes, that is only those involv-ing damage that considerably exceeds what the country or region concerned can handle itself so that substantial na-tional or international aid is required. That is generally the case if the number of dead runs into the hundreds or thousands, if tens or hundreds of thousands of people are rendered home-less and if the total economic loss is in the region of US$ 100 million. These major catastrophes, about which we have fairly comprehensive data even in the case of those that occurred farther back in the past, numbered only 14 in the 1960s but 70 in the 1980s; they there-fore increased over a period of 30 years by a factor of 5. The trend is also very clear when we consider the total economic loss, which - adjusted for in-flation - increased during the same period from an average of US$ 3.7 bil-lion per year to US$ 11.4 billion, i.e. by a factor of 3.1. The insured losses, finally, increased by as much as a fac-tor of 4.8.

Jan 1, 1990

By Mroczek C. R, Evans D. A

Renison is a world-class ore deposit that has been mined for over 100 years. It currently has reserves of 5.06 Mt @ 1.88 per cent Sn and a projected mine life of 8.5 years. Recent advances in the geological understanding of the deposit have been associated with detailed structural and geophysical investigations accompanied with the discovery and exploitation of the Rendeep orebodies. Mineralisation is linked to the forceful emplacement of the Devonian Pine Hill Granite that resulted in a complex brittle (-ductile) deformation of the Eo-Cambrian host stratigraphy. Dilation jog development on the Federal-Bassett Fault in the Federal and Rendeep areas provided access for cassiterite-rich magmatic hydrothermal fluids responsible for carbonate replacement Mineralisation.

Jan 1, 1997

The silver-lead ores of Yerranderie occur in a series of narrow, flat-dipping lodes in small bodies of quartz porphyry, intrusive into Upper Devonian volcanics, which are exposed in the western flank of the Permo-Triassic Basin of central New South Wales, about 80 miles south-west of Sydney (Harper, 1930; Lawrence, 1953). The lodes strike about E.-W. and are from 1,200ft. to 2,000ft. long. They consist of a series of ore shoots from 3ft. to 100ft. long, and up to 5ft. thick, though commonly under 2ft. thick, interspaced with low grade sections. They dip at from 18°S. to 400 S., and have persisted down the dip for 1,450ft. (693ft. vertical depth) in the Wollondilly mine, for 1,120ft. in the Bartlett's mine, and for 850ft. in the Wonga mine.The grade of ore in the Bartlett's mine was from 32% to 40% lead, from 100 oz. to 130 oz. silver per ton, 0.5 to 4.0% arsenic, with ore ,as rich as 20% arsenic on the No. 6 and No. 7 levels of the Silver Peak mine, the underlay extension of the Bartlett's lode, about 1% copper, and up to 4 dwt. gold per ton. In the Wollondilly mine the average grade was 15% lead, with sections as rich" as 36% lead, from 75 to 165 oz. silver per ton, 0.6 to 3.3% arsenic, 0.2 to 0.7% antimony, 0.8% copper, and up to 7...5. Cl~t. gold per ton. The zinc content of the ores is slight, and has not been recorded.Mining began about 1898, and to date more than 110,000 tons of ore, valued at £1,800,000, has been raised. Large scale mining ceased about 1935. The chief mines operating were the Bartlett's mine (formerly Colon Peak), the Silver Peaks, which is the underlay extension of the Bartlett's, the Wollondilly (or Yerranderie) mine, and the Wonga' (or Tonalli) mine.

Jan 1, 1953

A mechanised sub-level overhead benching method is used at Cleveland, to produce 22,000 tons per month of ore assaying 0.92% Sn and 0.40% Cu. The ore occurs in a series of vertical lenses which can be mined by open stoping. Levels are developed at 60ft., vertical intervals by jumbos. The ore is silled out and the stope block formed between levels drilled out by long hole drilling. Each row of holes is fired and broken ore within safe reach from the stope brow is mucked out by Wagner ST-5A Scoop Trams. The remaining broken ore is recovered on extraction of the next lower level. Ore is hauled by road to the crusher station from the mine. As mining proceeds below the lowest surface portal a spiral decline will be used for ore haulage and mine servicing.

Jan 1, 1970

The design of mine ventilation systems for the BHP Steel Division Collieries is based on the acquisition of ventilation survey data for the establishment of a realistic computer net- work model. The branches which form the net- work for the computer models are calculated from a range of resistance factors incorporat- ing both a frictional and shock loss component. Since shock losses can account for up to 30 per cent of the total energy losses in mine airways the use of friction factors alone without accounting for shock losses will result in the choosing of an insufficiently performing fan. Published tables of friction factors have in- variably been taken from metalliferous or single entry studies and consequently are not reliable for Australia's mining conditions where multiple entries with regularly spaced cut-throughs are the normal practice. Typical resistance factors for roadways of rectangular cross-section 5.5 m x 2.0 m, with coal sides, have been found to vary from 0.11 Ns2/m8/km where no timber supports are used, to 0.98 Ns2/m8/km where double centre legging together with wooden chocks is used. In addition to the range of resistance factors due to varying support methods, the nature of use for a roadway is very significant because of the condition of repair and upkeep maintained.

Jan 1, 1983

By Romanovsky N. P

The Pacific Mobile Belt (PMB) is characterized by old origin and complex evolution both in time and space. As the global structure, the PMB is a narrow tectonic region dividing two plan-etary hemispheres, viz. the Pacific and IndoAfro-Atlantic ones, the relative shifting of which defines the character of many geodynamic processes in this belt. The PMB features inhomogeneity of structure, special matter composition characteristics, sharply broken-out topography, and intensive fields. Generalized anomalies of the gravitational field closely correspond to the PMB boundaries defined by the real features, i.e. the andesite line and distribution areals of Mesozoic-Cenosoic granitoids. The belt boundary position is controlled also by seismic velocity anomalies at a depth of down to 200 km. The modern PMB deformation is defined by the left-hand equatorial shift and rotation of the Pacific Ocean counterclockwise. This rotation is non-uniform in time and of an oscillating character. The motive forces of the phenomenon are considered.

Jan 1, 1990

By Rath M. C, Das R. P

Studies were carried out on dissolution and oxidation of iron powder in ammonia-ammonium carbonate solution using oxygen over pressures. Cobalt and nickel losses during iron oxidation under different conditions were investigated. Regression equations were derived for percent cobalt loss and percent iron oxidation using ammonia, ammonium carbonate and oxygen partial pressure as the variables. The equations were tested for adequacy using Fisher's test. Cobalt losses increased with the increase of initial cobalt concentration and about 400 mg/l of cobalt was lost from a solution containing 500 mg/l cobalt. A maximum of about 80 mg/l nickel was lost from 1 g/l nickel containing solution, and this loss remained the same even when the nickel concentration was increased to 7.5 g/l.

Jan 1, 1992

By G Gibson, B Bessen

In coal preparation, large dense medium cyclones (DMC) at low pressure heads (typically 9D where D = cyclone diameter) are the norm. This contrasts with high density mineral applications where, largely for historical reasons, smaller cyclones at high heads are the standard. There are advantages in preferring large diameter cyclones at low heads, assuming that metallurgical performance does not suffer significantly. These include simpler plant layouts, easier maintenance, smaller spares inventories, reduced wear, reduced medium pumping demands, smaller buildings and overall lower capital and operating costs. In 2008, therefore, Xstrata Zinc decided to trial a single DSM-design 800 mm cyclone in one of its four DMC lines at Mt Isa, replacing the four 400 mm cyclones previously installed. Circumstances allowed a low head of 9.5 D to be trialled, compared with the existing 400 mm head of 21.5 D. This paper describes the trial, including tests using painted ore particles as tracers, estimates of yield and metal recovery, and wear monitoring. The larger unit performed well. There was no evidence that metallurgical performance in terms of metal recovery and waste reject rate suffered, and there was some evidence that it may have improved. Cyclone life increased, and preliminary data suggest that the replacement cost of the 800 mm cyclones is less than half that of the 400 mm units, and this is expected to improve. The plant layout and operability have also improved significantly. Xstrata has therefore decided to convert the whole plant to four low head 800 mm units, replacing the original 16 high head 400 mm units. The paper includes an explanation of the effect of static head on DMC separating force. It also reviews earlier research on diamond applications, and applies a general DMC process model to the Xstrata case, both of which confirm that large, low head cyclones are appropriate in mineral applications, contrary to conventional practice. Such units could significantly reduce both the capital and operating costs of DMC plants in mineral applications.

Jan 1, 2009

By Emerson J

Drilling has always been one of the most important parts of the exploration process with most companies spending around 25% of their budget on drilling. Although superficially there appears to be little difference in drills and drilling practice a number of major refinements have taken place over the last decade that have significantly changed the drilling scene. One of the most important advances has been in hydraulic engineering giving rise to the Dual Purpose top drive drilling rigs. These have led to significant productivity increases with the high rotation speeds and longer fleets. Downhole technology has also advanced with better hammers, stronger drill rods, impregnated coring bits and improved drilling fluids. Although geologists continue to measure drilling performance on a cost per metre basis, greater consideration is at last being paid to the quality of sample produced. This is particularly the case with RC drilling where quite sophisticated automatic and semi automatic splitting devices have been developed. Drill operators are now required to be experienced in both Diamond coring and air drilling and be better qualified to maintain the more sophisticated machinery. Management of drilling companies or drilling divisions has also had to change to accommodate both the high capital cost of equipment and the demands of keeping drilling a cost effective exercise.

Jan 1, 1987