Search Documents

By J J. Boshoff

This iron ore mine site, located in the Pilbara region of Western Australia, commenced operations in 1998, with ore derived by mining of open-cut pits in Channel Iron Deposits (CIDs). A portion of the ore extracted at the mine is processed at wet processing plants that produce both ore saleable product and waste fines (i.e. tailings) slurry. The waste fines produced at the wet plants are presently stored within Waste Fines Cells (WFCs).Waste fines cells A (WFCA) and B (WFCB) are located within an Autonomous Haul System (AHS) area and consist of embankments that span the width of the pit in east-west alignments. Technical studies and design analyses were carried out to support embankment raises and ongoing development of the WFCs. During operation and development of the WFCs, a multitude of simultaneous activities took place to the immediate north and south of WFCA respectively. These activities included the construction of the embankment raises using the AHS fleet, mining of the CID to not only mine the ore but to also create future deposition space for WFCB, blasting next to the WFC embankments as part of the mining activities, seepage collection and dewatering of the pit in the vicinity of the WFC.This paper discusses the material characteristics, design approach, construction staging and equipment requirements, blasting near embankments, water management, facility consequence category and closure concept.CITATION:Boshoff, J J, 2018. A waste fines cell with a multitude of concurrent activities, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 39–49 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By Eggleton R. A, Taylor G

As the search for major orebodies continues, the regolith dominated areas of the Broken Hill region remain one of the major exploration frontiers. The past exploration philosophies emphasising bedrock related characteristics have been limited in their ability to effectively explore in the regolith dominated areas, that are a feature of most of the Broken Hill region (Figure 1). If mineral exploration is to be more effective across all of the Broken Hill region, particularly in the regolith dominated areas, an appreciation and increased understanding of the regolith and landscape features are a necessity. Ironically, there have been very few studies of the regional regolith and landscape features of this region. Owing to the previous lack of an established regolith-landform framework, this study initially concentrated on the general characterisation and variation in regolith types corresponding to the area of the Broken Hill Block, within NSW (Willis, 1989; Stevens, 1986). The approach has been to produce a regional regolith-landform map at 1:100 000 scale and conduct a complimentary program of regolith sampling and site descriptions. This was a basis to identify areas for more detailed regolith-landform mapping (1:25 000 scale) and for producing a regional stratigraphic framework and models for landscape and regolith evolution. This information can then be used to provide a basis for regional mineral exploration models and strategies. This paper highlights some of the regionally significant regolith-landform features and their general significance to mineral exploration. More detailed information on specific regolith-landform features and study sites may be found in Hill et al (1994; 1996; in press) and Hill (in prep).

Jan 1, 1997

Ore deposit modelling is becoming an increasingly accepted tool in mineral exploration. Successful models have already been proposed for several ore deposits of base metals and gold, but tin has so far received comparatively little attention, perhaps because of an excessive preoccupatioi with alluvial operations. This situation is rapidly changing and some of the world's most profitable and newly commissioned tin mines are large, primary tin deposits. Some basic principles of ore deposit modelling are briefly reviewed and the fallacy of an excessive reliance on grade tonnage diagrams based on the tin industry worldwide is discussed. The four proposed models and submodels of large, hard-rock, tin deposits focus on basic concepts such as the spatial relationship with "tin granites", depth of emplacement and the level of erosion. General concepts are drawn. The modelling of large primary tin deposits is reviewed not only in its geological and exploration aspects but also in its mining and economic implications.

Jan 1, 1986

Lithocaps are potentially voluminous zones of advanced argillic and associated argillic alteration located above the subvolcanic intrusive environment. They constitute exploration objectives for epithermal and porphyry-type deposits. High-sulphidation epithermal deposits may be sought within lithocaps, whereas low-sulphidation deposits may exist on their edges. Porphyry Cu-Au/Au deposits may be accessible beneath lithocaps if systems are telescoped sufficiently. Oxidation of the basal, pyritic parts of lithocaps may promote supergene sulphide enrichment under appropriate tectonic and climatic conditions.

Jan 1, 1995

By Shatwell DO, Hayward SB, Leach TM

Following acquisition of the Woodlark Island tenement by Highlands Gold Limited, an exploration programme using extensive diamond drilling has confirmed that the style of gold mineralisation is similar to other SW Pacific Rim carbonate base metal gold systems. The two centres of gold mineralisation at Kulumadau and Boniavat-Busai are inferred to be related. to buried porphyry centres localised on NE trending major horst bounding structures. Individual prospects are localised on NW trending cross structures peripheral to the porphyry centres.Gold mineralisation has been derived from the mixing of hot saline magmatic fluids with cool dilute meteoric waters. While the bulk of mineralisation occurs in dilational tensional gash fractures, bonanza grades resulted from fluid quenching in feeder structures. Pre-mineralisation breccias created plumbing systems for hydrothermal fluids and similar paragenetic sequences are defined for Busai and the Kulumadau areas. These include early, distal porphyry, low sulphidation mineralisation, followed by base metal gold and carbonate deposition.

Jan 1, 1994

By Bearman R. A, Parkin R. M

In the comminution industry cone crushers are widely used for secondary and subsequent stages of size reduction. Traditionally cone crushers have been operated and monitored manually. Alteration of discharge setting is now commonly achieved via hydraulic means, however, compensation of liner wear can still involve plant shutdown and loss of production. Drift in discharge setting due to liner wear is still a major problem that must be addressed to improve product quality, consistency and reduce recirculating load. The continuous demand for better quality products and the high cost of reprocessing or discarding unsaleable material, highlights the need for re-examination of the technology associated with the crushers to ensure optimum control and system efficiency. A collaborative project between Pegson Ltd, one of the leading UK manufacturers of jaw and cone crushers, De Montfort University Leicester, and Transfer Technology plc was established to address the technological requirement for automation of the control of cone crushers. The machine chosen for the study is a 900 Autocone cone crusher manufactured by Pegson Ltd. The design philosophy is based on a mechatronic approach providing a complete solution through a distributed network of intelligent sensors, artificial intelligence technology and adaptive control. The modular design of the system ensures a progressive sophistication in technology that allows the automation to be phased in as required. This will ensure maximum benefits to all sectors of the aggregate industry. It is estimated that the automation will result in savings of around ten per cent. The savings will result from minimising the production of unsaleable products by reliable condition monitoring and automation of the control and maintenance of system parameters to optimise system efficiency. Extension of the methods and principles into the mining sector is anticipated. The control over the size of crusher product will offer great benefits to the mining industry with significant implications for subsequent milling and beneficiation processes.

Jan 1, 1995

The Yabulu refinery of Queensland Nickel Pty Lld near Townsville now imports more than three million wet tonnes per year of nickel laterite ore from New Caledonia and Indonesia, making it the largest importer of any commodity in Australia. The project has illustrated that importing untreated bulk ore and re-exporting high value products makes good economic sense for the company and the nation.The economics of this exercise were considerably enhanced in 1994 by changing the project's principal product from nickel-oxide sinter to refined high-purity nickel metal. It is one of the few operations in the world where nickel ore is transformed to nickel metal at a single site.Several novel technological processes were developed at Yabulu and incorporated into the refinery to allow this product transition to occur. By utilising internally developed technology the new processes were installed at a capital cost of less than $10 million. It is unique for a large nickel producer to change completely the quality of its entire product range many years after the plant was constructed and considerable attention to marketing the new products has been required.The changes have meant that the project is no longer limited to selling lower-value oxide sinter to a relatively small number of large stainless steel mills. In the past year sales of the new high purity nickel metal products have expanded to include a broad range of international customers in the special alloy, foundry and chemical industries.

Jan 1, 1995

By Kapoor M. L

EMF measurements were performed in the temperature range of 933-1095 K to determine the thermodynamic properties of oxygen dissolution in liquid lead and lead-tin alloys with tin in the dilute concentration range of 0 to 6 atom per cent. The oxygen in the Pb-O system was varied by equilibrating with (PbO) slag, and that in the Pb-O-Sn system was varied with the addition of lead oxide. Wagner's interaction parameter approach was used to evaluate the self interaction parameter and ternary interaction parameters at different temperatures, to yield: E8(pb) = 97.35 - 113.27 x 103/t Eo(pb) = 139 - 20.616 x104/1' Quasichemical formulation was employed to yield Inf to reveal the effect of tin on oxygen in lead. Results have been predicted on the basis of classical models and those obtained using the QCT approach of Alcock and Richardson at Z=2 have been found to agree with the experimental Data.

Jan 1, 1992

By Y Li

An ilmenite ore from the Murray Basin was initially characterised using combined X-ray Fluorescence Spectroscopy (XRF), X-Ray Diffraction (XRD), Scanning Electron Microscope (SEM) and Electron Probe Microanalysis (EPMA) techniques. XRF analysis showed the ilmenite sample contained 58.7 wt per cent TiO2 and 26.2 wt per cent Fe2O3. Major impurities included: Cr2O3 (4.5 wt per cent), Al2O3 (2.7 wt per cent), SiO2 (1.9 wt per cent), Mn3O4 (1.5 wt per cent) and MgO (1.1 wt per cent). Manganese and magnesium were present as solid solution components within the ilmenite lattice while the elevated Al2O3 and SiO2 levels were due to separate aluminosilicate gangue minerals. Chromium was associated with discrete chrome spinel gangue phases of variable composition, (Fe,Mg)(Cr,Al)2O4. Quantitative XRD analysis of the sample identified rutile (12 per cent), ilmenite (11 per cent), and pseudorutile (67 per cent) as the main titanium-containing phases and chrome-rich spinels (seven per cent) as the major impurity phase. Minor quartz, aluminosilicates, zircon and monazite were also present. The ilmenite was mixed with synthetic graphite, pressed into pellets and reduced carbothermally in nitrogen at 1200 and 1400°C with C/O molar ratio of 1.2. Titanium oxide in the ilmenite was converted to titanium oxycarbonitride. Iron oxides were reduced to metallic iron. The Changes of impurities as a result of reduction was examined by SEM and EPMA analyses. Iron and chromium oxides within Fe-rich chromite were reduced to form a Fe-Cr-C alloy. Mg-rich chrome spinels were partly reduced at 1200°C. Zircon particles were not reduced at 1200°C, but were significantly reduced at 1400°C, with the particles becoming porous and the silicon being removed.

Oct 5, 2011

The æMountain Camp reefÆ at Alford's mine, Wakamarina,Marlborough, had no recorded gold production although assays of 5 - 26 g/t were reported, but it did produce c. l000 kg of scheelite. The lode consists of a lower massive quartz layer, and upper, cm-banded, ribboned quartz layers, and has a very low sulphide content. Within the massive layer, relict early fine-grained mosaic quartz with idioblastic scheelite is surrounded by recrystallised granoblastic coarse-grained quartz with calcite and plagioclase, in which an original ribbon banding texture is mimiced by strings of tiny inclusions. In both the banded and massive layers, rounded quartz grains, created by cataclastic milling of grain margins and along syn-vein fractures, have been partially annealed within later quartz overgrowths. Late fibrous quartz and calcite fill brittle cross fractures.   Deformation events D1 and D2 are associated with mid-late Jurassic metamorphism of the Pelorus Group, D2 producing the main regional schistosity (S2, and the earliest scheelite. D3 is an extensional mylonitic shear event that formed the dominant schistosity in Alford's mine (S3). The quartz lode was emplaced within the mylonite by a series of individual dilation pulses (D4). The D5 event caused crenulation of the S3 mylonite, kink banding and chevron folding of the S2 schist and S3 mylonite, and reverse faulting, rodding and cross-fracturing with late fibrous quartz-calcite veining of the D4 quartz lode.   Fluid influxes during successive dilations of D4 fractures progressively caused recrystallisation of earlier quartz bands on the footwall, annealing and recrystallisation of quartz along milled crystal margins and fractures, and deposition of minor sulphides. There was thus a dynamic interplay between fault dilation, lode fracture, fluid influx, lode band deposition, and lode recrystallisation. Illite-Kfeldspar al ¦ 2 Ma (K/Ar), c.30 Ma after metamorphism.

Jan 1, 1996

By P M. Ashley, M T. Costelloe

The Mary Kathleen tailings storage facility (TSF) contains 7.1 Mt of uranium mill tailings. This waste repository was rehabilitated in the mid-1980s using a multibarrier dry cover. At the time of mine closure, it was predicted that acid mine drainage (AMD) generation would not eventuate and that uranium, heavy metals and radionuclides would be adsorbed within the tailings and not seep from the TSF into the environment. This study reports on the environmental status of the TSF. Gamma-ray measurements indicate an intact dry cover of the waste repository. However, seepage (~0.5 L s-1) of acid (pH 5.71), saline (0.31 per cent), high conductivity (8.8 mS cm-1), slightly oxygenated (DO 2.6 mg L-1), radioactive waters occurs from the toe of the tailings dam into the former evaporation ponds and local drainage system. Seepage waters are calcium-magnesium-sulfate rich with elevated Fe, Mn, Ni, U and Zn values. Oxygenation of tailings seepages causes the precipitation of Fe and coprecipitation and adsorption of other metals (Pb, U, Y), metalloids (As), rare earth elements (Ce, La) and radionuclides (U-235, U-238, Th-227). In contrast, Ba, Ni, Sr, Mn, P, S, Ca, Mg, Na and K as well as Ra nuclides (Ra-226 and Ra-228) remain in solution until pH neutralisation and evaporation lead to their precipitation in efflorescences and sulfate-rich evaporative sediments further downstream. Dry capping of Mary Kathleen uranium mill tailings has resulted in physical containment of the wastes. The dry cover shows no signs of erosion and radiation levels are within acceptable limits. However, the flow rate of surface seepage from the TSF occurs at a much higher rate than predicted. Also, the neutralising potential and adsorption capacity of the tailings and underlying aquifer were overestimated at the time of mine closure. AMD has developed mobilising metals, metalloids, rare earth elements, alkalis, radionuclides and sulfate from the waste repository into surface water seepages.

Jan 1, 2003

The Myra Falls minesite, of Westmin Resources Limited, is located at the geographic centre of Vancouver Island, within the confines of Strathcona Provincial Park. The operation includes two active underground mines, II-W and Lynx, together with a modem 3650 1/d milling facility. Recent exploration successes will lead to the commissioning of a third mining area in late-1993 - The Battle/Gap Mine. These ore deposits are complexly metal-zoned volcanogenic massive sulphides of Devonian age, hosted in the Myra Formation of the Sicker Group volcanic assemblage. Three distinct felsic volcanic units are defined within the 450 metre thick Myra Formation. They are, from oldest to youngest, the H-W Horizon, the LMP Horizon and the Upper Rhyolite Unit. Massive sulphide mineralisation occurs throughout the property in the H-W and LMP Horizons. There are a number of orebody types, including polymetallic massive sulphides, polymetallic disseminated sulphides, zoned pyritic massive sulphides, elastic sulphide zones and stringer sulphide zones. Individual orebodies range in size from 10 000 tonne zinc-rich polymetallic lenses to the ten million tonne, zoned massive sulphide H-W main lens. The property has been in continuous operation for 26 years, producing over 13 Mt of ore averaging 2.2 g/t Au, 64.0 g/t Ag, 1.9 per cent Cu, 0.6 per cent Pb, and 5.6 per cent Zn. Current geological reserves stand at 12.5 Mt at a comparable grade, including 4 Mt of recently discovered high grade ore in the Battle and Gap Zones. Mining and milling methods have evolved over time to enable successful extraction and milling of these complex ores. Change is on-going with the recent conversion of the H-W Mine to large-scale bulk mining methods, and the development of effective computerised ore reserve calculation and mine planning tools. These changes, in concert with successful exploration techniques that led to recent high grade ore discoveries, have breathed new life into the operation and should assure its present and future viability.

Jan 1, 1993

The transition from low stress to high stress conditions is a challenge eventually faced by most mines in Australia that extend to depths greater than (generally) about 1000 m. In areas with strongly adverse 'stress versus depth' gradients, such as some parts of Western Australia, significant stress-related problems have occurred at depths as shallow as 300 m below surface. The actual depth at which the 'transition' occurs is a function of the local pre-mining stress field, the strengths of the various rock types hosting the deposit and the layout and sequencing adopted in the mine. Stress-related damage can result in increased support costs, and delays associated with rehabilitation and disruption to production. In the worst case, where strong seismicity and associated damage occurs in active mining areas, 'exclusion' zones and 're-entry' protocols may be required. These can severely disrupt production. A key aspect of managing the transition is the recognition of the onset of stress-related ground behaviour. Damage mapping can be used to develop understanding of the relationships between mining activities and the local and regional response to them. Carefully documented case histories provide a basis for calibrating numerical models. This paper discusses some of the typical styles of ground behaviour observed in higher stress conditions in underground mines. A simple damage classification scheme is described to assist in 'damage mapping' of mine tunnels. An example of damage mapping is presented to illustrate an approach commonly used for recording stress-related damage.

Nov 25, 2010

By Brimblecombe P

Morwell Open Cut is a continuous mining operation employing 5 buck- etwheel excavators, I bucket chain excavator and 54 conveyors. The combined bunkering capacity at both client Power Stations represents less than 12 hours maximum coal demand. This creates an extremely dynamic operating environment, which is further complicated with significant variations in both excavating and transportation plant capabilities. To achieve set objectives, including- I adequate reserves, 2 coal supply reliability, 3 cyclic plant maintenance, 4 minimal cost of coal, scheduling of the operation requires constant monitoring and reappraisal.

Jan 1, 1989

By Savage E. N

Two genetic types of base metal deposits occur in the Wainivesi area of central eastern Viti Levu. The Wainivesi deposit is now considered to be a stratiform volcanogenic type, and the Wailotu and Wainiviti deposits are described as contact metasomatic with some hydrothermal manifestations. The Wainivesi mineralization is correlated with the Tertiary "e" stage, i.e. uppermost Oligocene-Iowermost Miocene. Tertiary "e" stage rocks in Fiji are therefore potential ore producers of stratiform volcanogenic type. On the basis of plate tectonics with Fiji part of the New Hebrides Arc prior to rifting apart in the late Miocene, stratiform volcanogenic deposits of the Wainivesi type may also occur in rocks of comparable type and age in the New Hebrides.

Jan 1, 1976

By Loo C. E

Thirty two polyacrylamide flocculant samples were selected from the wide range offered to the Australian coal industry. An extensive test program was conducted to consider the properties of the flocculants, the substrates, the process conditions and the water chemistry encountered in coal preparation plants. The study indicated that flocculants with molecular weights of 12 to 14 million and degree of hydrolysis around 40% gave the best "average" performance over a wide range of process conditions. The pick-up and filtration of fine coal was demonstrated on a pilot scale to be a critical function of flocculant properties. This study also showed that the agitation intensity during flocculation was a critical parameter in determining the settling rate of the slurry and the clarity of the resulting supernatant. An electronic meter to measure agitation intensity was designed, constructed and tested to demonstrate how, for the first time, laboratory results can be implemented in operating plants.

Jan 1, 1989

By T GRAHAM-TAYLOR

A trend towards mining more complex and economically marginal orebodies, often combined with increasingly tight product specifications, increases the number of variables which need to be considered in production scheduling. Linear programming incorporating integer constraints can be used to create production schedules which are practical as well as mathematically optimum. Factors which can be taken into account include variability in product stockpiles, targets for head or product grades, production of different material types, production from different areas, production targets for loaders, and dependencies between mining blocks. For each schedule an appropriate objective for optimisation must be chosen. Examples of objectives are: to minimise or maximise grade variation; to minimise waste movement; and to minimise movement by front end loaders. A staged approach to the implementation of computer systems based on linear programming optimisation is Proposed.

Jan 1, 1992

Before presentIng my address I wish to acknowledge the honour which has been conferred on me by my appointment to the position of President of the Australasian Institute of Mining and Metallurgy.It is a matter of great concern to us all to find our Empire at war. I am confident that, as was the case in the war of 1914-1918, members of this Institute and of kindred Institutes and Associations will contribute in full to the Empire's needs and that in the end our cause shall triumph.I think it appropriate that I should take as the subject of my address that of the Broken Hill Lead-Silver-Zinc Industry. The subject matter of this address has been confined to the operations of Mining, Ore Dressing, Lead Smelting and Refining and production of Electrolytic Zinc in Australasia. The review of the Broken Hill Lead-SilverZinc Industry would not, of course, be complete without reference to those Australian industries which trace their origin to the Broken Hill field, but· it is thought that an outline of these industries would make thIs review too extensive.HISTORICALMany efforts have been made to translate the early history of Broken Hill and its subsequent growth throughout the years into one of the wor~d's most famous mining fields in the form of a simple story.

Jan 1, 1940

By A Kamaraj, M Mohanasundaram, R Kumar, P Tikare

This study presents a comprehensive thermodynamic optimisation and sustainability analysis of the secondary copper smelting process for Waste Printed Circuit Board (WPCB) recycling. The study investigates various scenarios with different proportions of WPCB in the input stream, ranging from 0 per cent to 100 per cent. Through thermodynamic modelling using FactSage™ version 8.1, the optimisation process is conducted in three stages. The results of the thermodynamic modelling indicate that the best-case scenario for WPCB recycling is achieved with a 40 per cent proportion of WPCB in the input stream. This case exhibits a maximum copper recovery of 99.93 per cent while minimising the formation of other waste. In addition to the thermodynamic analyses, environmental factors such as the carbon emission index and resource utilisation efficiency are studied. The 40 per cent WPCB recycling case exhibits a resource utilisation efficiency of 93.055 per cent and a carbon emission rate of 0.133. The present investigation highlights the significant benefits of a 40 per cent WPCB recycling scenario through a secondary copper smelting process in terms of base metal recovery and energy efficiency, thus emphasising its potential for sustainable PCB waste management and resource utilisation.

Aug 21, 2024

By Lawson F

Narrowly sized samples of synthetic chalcocite (Cu2S) and covellite (CuS) were leached in oxygenated acidic sulphate-chloride solutions. Chalcocite leaches via a two-stage process, the first stage being much more rapid than the second. The apparent activation energies are 42.7 kJ/mol and 68.2 kJ/mol respectively, indicating that both stages are controlled by surface chemical reactions. The leaching of covellite is also chemically rate limited with an apparent activation energy of 77.0 kJ/mol. The shrinking core model is able to be used to describe the leaching processes of both copper sulphides. Over 97% of copper present in chalcocite dissolved in 0.5 M H2SO4i0.5 M NaCl solution under one atmosphere pressure of oxygen at 85¦C in three hours from particles 36 pm in diameter while only 85% of the contained copper in covellite particles 13 pm in diameter dissolved in the same solution under the same pressure at 90¦C in six hours. About 99% of the sulphide sulphur in chalcocite was oxidised to elemental sulphur while only 90% of sulphide sulphur was converted to elemental sulphur during covellite leaching. The mechanism proposed for the two-stage leaching of chalcocite particles is as follows: in the first stage, cuprous ions rapidly diffuse to the external reaction surface where they lose electrons and go into solution as a complex cupric chloride ion CuCl'. The second leaching stage begins when covellite is formed at the external surface. Copper again goes into solution as the CuCl* ion. The mechanism for leaching synthetic covellite is similar to the second leaching stage for chalcocite except that the leaching rate of synthetic covellite is substantially lower than that of the newly formed 'covellite'. Elemental sulphur formed on the particle surface retards the dissolution processes during both chalcocite and covellite leaching. The presence of chloride ions is necessary if essentially all of the copper from chalcocite is to go into solution. When no chloride ions were present, the leaching rate of both newly formed and synthetic covellite was almost zero. The main role of chloride ions in both chalcocite and covellite leaching appears to be to disrupt the passivation film of sulphur on the particle surface.

Jan 1, 1989