Search Documents

By Walter R. Hibbard

BACKOFEN' reported recently that "the deformation texture of cold-drawn OFHC copper wire, after a reduction in area of 97.3 pct, may still be described as a composite of [lll.] and [loo] directions aligned parallel to the wire axis." In the introduction, he indicated that this was in contrast to the work of Hibbard,' who reported a single [111] texture after a reduction of 96.4 pct. Unfortunately Backofen stated that this was a reduction in area when actually it was a reduction in diameter, as is clearly stated in the reference. Moreover, the results of Backofen are in complete agreement with the results of Hibbard. Backofen's 97.3 pct reduction in area is an 83.3 pct reduction in diameter, after which he foundadouble [ll11 and[l001texture with the former predominating. Similarly, Hibbard; after an 86 pct reduction in diameter found a double [Ill] and [I001 texture with the former predom- inating. Hibbard, however, when he drew the wire further to 96.4 pct reduction in diameter, found primarily a single [Ill1 texture as illustrated by Fig. 2 of ref. 3. Here also, Hibbard- reported evidences of the [loo] recrystallization texture found by Backofen. It might also be pointed out that Backofen not only drew his wire 97.3 pct reduction in area but also etched them over 99 pct reduction in area from 0.125 to 0.01 in. diam. Hibbard's wires were drawn directly to size. In summary, the deformation texture of cold-drawn copper wire still may be described as primarily a single Clll] texture after a sufficient amount of drawing, such as 96.4 pct reduction in diameter." a

Jan 1, 1952

By Janshi Sen

Vertical-intensity magnetometers, for instance the Hotchkiss Superdip and the Askania vertical field balance, are now widely used, because vertical-intensity charts give definite information for the location of upper pole, dip and strike, and approximate shape of the deposit. Again, a slow and steady increase of dip over a large area indicates a large deep-lying deposit, while a large dip limited to a small area and falling away rapidly suggests a small and shallow one. The complication comes more from the richness of the ore. A large body of lean ore near the surface might produce the same vertical-intensity chart as a rich ore at depth. This paper presents a method for calculating the maximum depth of a single-pole deposit and another for a two-pole mineral body, by utilizing data of both vertical and horizontal intensities as obtained by a Thalen-Tiberg magnetometer. As shown on the left side of Fig. I, lean ore, rich ore and a single pole produce the same magnetic field. The depth of the pole, where G is the vertical intensity at point A due to the pole; F, the horizontal intensity of the same; and a, the distance from the point of maximum vertical intensity or the vertical projection of the pole on the surface to the point of observation A. If an entirely covered deposit is indicated by magnetic measurements and boring cost estimated from the calculated depth is so reasonable as to encourage drilling, the ore should be struck somewhere within the limit of the calculated depth by the borehole. A number of such points as A should be taken for calculation, erratic results should be rejected and the average figure used for cost estimation.

Jan 1, 1946

By Janshi Sen

Vertical-intensity magnetometers, for instance the Hotchkiss Superdip and the Askania vertical field balance, are now widely used, because vertical-intensity charts give definite information for the location of upper pole, dip and strike, and approximate shape of the deposit. Again, a slow and steady increase of dip over a large area indicates a large deep-lying deposit, while a large dip limited to a small area and falling away rapidly suggests a small and shallow one. The complication comes more from the richness of the ore. A large body of lean ore near the surface might produce the same vertical-intensity chart as a rich ore at depth. This paper presents a method for calculating the maximum depth of a single-pole deposit and another for a two-pole mineral body, by utilizing data of both vertical and horizontal intensities as obtained by a Thalen-Tiberg magnetometer. As shown on the left side of Fig. I, lean ore, rich ore and a single pole produce the same magnetic field. The depth of the pole, where G is the vertical intensity at point A due to the pole; F, the horizontal intensity of the same; and a, the distance from the point of maximum vertical intensity or the vertical projection of the pole on the surface to the point of observation A. If an entirely covered deposit is indicated by magnetic measurements and boring cost estimated from the calculated depth is so reasonable as to encourage drilling, the ore should be struck somewhere within the limit of the calculated depth by the borehole. A number of such points as A should be taken for calculation, erratic results should be rejected and the average figure used for cost estimation.

Jan 1, 1946

The following is an incomplete list of members and guests who called at Institute headquarters during the period Sept. 10, 19188 to Oct. 10, 1918. Thomas J. Adams, Rahway, N. J. A. N. Mackay, London, England. Henry M. Ami, Washington, D. C. A. W. MacNichol, San Francisco, Cal. Chester Atkinson, Peru, South America. Ernest Marquardt, Casper, Wyo. Bennett R. Bates, Berkeley, Cal. Lieut. S. A. Mewhirter, Denver, Colo. Robert S. Botsford, Petrograd, Russia. William A. Nelson, Nashville, Tenn. Juan Felix Brandes, Santa Barbara, Cal. Robert W. Olinger, Bahia, Brazil, So. G. A. Collins, Seattle, Wash. Amer. C. V. Corless, Coniston, Ont., Canada. G. Preumont, La Paz, Bolivia, So. Amer. F. T. Eddingfield, Washington, D. C. William H. Rettie, Yonkers, N. Y. C. Mason Farnham, Barre Plains, Mass. . Julius Segall, Minneapolis, Minn. F. N. Flynn, Trail, B. C., Canada. Robert Y. Seip, Franklin, N. J. Duncan D. Forbes, Humboldt, Ariz. H. M. Schleicher, Boston, Mass. Alexandre Gouvy, Paris, France. Chester Steinem, Ft. Monroe, Va. Henry G. Granger, Cartagena, Colombia, A. L. Sweetser, Pittsburgh, Pa. So. Amer. . H: E. Treichler, Creighton Mine, Ont., E. Harms, El Paso, Tex. Canada. Alfred G. Heggem, Tulsa, Okla. Frank A. W. Tullock, Yumbo, Colombia, H. B. Henegar, Mascot Tenn. So. Amer. A. M. Kivari, Denver, Edward I. Williams, Ft. Monroe, Va. T. M. Kniffin, Brookline, Mass. Alfred W. G. Wilson, Ottawa, Canada. Charles Lehman, London, England. Donald H. McLaughlin, Camp Meade,Md. C. E. Addams, who recently resigned as general manager for the Arizona Hercules Copper Co., has leased the Ray silver-lead property three miles from Ray, Ariz. Bennett R. Bates has resigned his position as general superintendent of the Cubo Mining & Milling Co., in order that he may take the examination for an officer of engineers.

Jan 11, 1918

WHAT was certainly the greatest event of January, and perhaps it will prove to be the greatest of 1923, or even of the next decade, was the meeting of the premiers of the principal Euro-pean powers in Paris on Jan. 2, to consider what should be done with respect to German reparations. The French and British were unable to come to any agree-ment, and the conference broke up on Jan. 4. The French and British parted friends, but each with the determination henceforth to pursue its own economic and political way. This event was profound in its significance and perhaps will be calamitous) in its consequences. Following the disruption of the Conference at Paris, the French immediately began preparations to occupy the Ruhr district on the ground that Germany was in default on coal deliveries, without waiting. for Jan. 15, the next due date for reparation payment. This action by the French led to orders being issued by President Harding on Jan. 10 for the withdrawal of the remainder of the American troops on the Rhine. Thus ended the physical participation in. European affairs by the American army, whose vanguard landed in France in June, 1917. The French occupation of the Ruhr Valley, i.e., the great industrial region of western Westphalia, was made with a large military force. The Germans offered no physical resistance, and passed under French control with sullen resentment. The coal miners to a con-siderable extent refused to work and there was more or less disorganization of railway service. Before the end of the month the opinion was expressed that the French occupation was an economic failure and there were reports of French blast furnaces being blown out for lack of coke.

Jan 2, 1923

By L. Dudley Stamp

On April 1, 1937, Burma, formerly a province of the Indian Empire, was formally separated from India and became an independent unit of the British Commonwealth. In future, therefore, statistics of oil production in India will exclude Burma and those for Burma will be separately published. The last few years have been marked by noteworthy, almost spectacular, developments in the oil fields of Burma and the Punjab. In Burma these developments have been the proving of unexpected extensions of the existing fields and not the discovery of entirely new fields. The new extensions are important not only to Burma in giving a new lease of life to her fields, but also in general as stressing some interesting geological aspects hitherto neglected. Production The production of crude oil in Imperial gallons has been: Burma India 1934 254,760,070 67,265,210 1935 251,338,974 . 71,323,362 1936 265,656,393 69,241,504 1937 (eat.) 270,000,000 70,000,000 The Chindwin Fields.—The small field at Indaw continues to produce steadily about 3,000,000 gal. a year, but no really deep test has yet been successfully carried out and resources are thus not yet fully known. The remote location of the field, inaccessible except by river and situated 22 miles from the Chindwin 270 miles up that river from its junction with the Irrawaddy, has not encouraged active exploitation. The field is worked exclusively by the Indo-Burma Petroleum Co., Ltd. (I.B.P.), using now an automatic gas-lift system, and the company formerly refined the oil at a small refinery at Pantha on the river near by. The chief market was for kerosene in upper Burma. The refinery has now been closed. The oil is stored on the field during the low-water season

Jan 1, 1938

By Edwin R. Walker

The old adage, " Necessity is the mother of invention," is fully borne out in the case of the device described in this paper. About four years ago the firm of the writer received instructions from Sir John Hawkshaw, C. E., and I. Wolf Barry, Esq., C. E., to construct and erect three large Guibal fans for ventilating a portion of the Metropolitan and District Underground Railway, of London. On account of the cost of coal and the very limited space for boilers, it was arranged that the fans should be driven by gas-engines. Those who have had experience with Guibal fans will be aware that as each blade or vane passes the lower edge of the shutter a pulsatory action takes place. When the fans above mentioned were set to work, the pulsation or vibration of the immense volumes of air discharged was so great that it caused a corresponding vibration of the window-sashes, doors, etc., of the surrounding buildings; and this was so unpleasant that the shopkeepers and others near obtained an injunction against the railroad company, compelling it to stop one of the fans. The work was by this time out of our hands, and we only casually heard what had taken place, learning also that, in addition to this injunction, another was threatened in the case of the second fan, and that the railroad company had thus far escaped the enforcement of this threat by agreeing to run the second fan at a few short stated intervals only during each day. In considering the case, it occurred to us to incline the lower edge of the shutter, instead of making it parallel with the axis of the fan,. by which means we thought that the waves of air might be broken

Jan 1, 1891

By J. L. Stuck

Geological investigation and research have contributed greatly in making industrial minerals the basis of an important industry in the state. North Carolina contains a wide variety of industrial minerals and rock. Mica, feldspar, kaolin, halloysite, talc, pyrophyllite, silli-manite, and spodumene are used to illustrate the progress being made. IN a previous paper1 an attempt was made to indicate the importance of industrial minerals in North Carolina and the wide variety of such materials present. The present paper is concerned with geological investigation and research which have made industrial minerals the basis of an important industry in the state. Geological mapping has gone through three stages in North Carolina during the present century. The first stage is represented by excellent reports of which Corundum and the Peridotites of Western North Carolina,2 Volume I, now a classic, is representative. In this report, a geologic map of the western third of the state is shown on a scale of 10 miles to the inch. The next stage is represented by folios" of the U. S. Geological Survey published between 1902 and 1932. Most of these contained 30 min quadrangle maps on a scale of 2 miles to the inch. The third step is represented by reports prepared during the past 10 years which contain geological maps4 on scales varying from 500 ft to 1 mile to the inch, while many mine maps have been prepared on scales varying from 20 to 150 ft to the inch. As the scale on which geological mapping has been done has decreased, the amount of information secured has increased. Pratt and Lewis did excellent work on the peridotites of western North Carolina, but their maps lacked details. Keith and others added

Jan 1, 1952

By Merrill Horine

IT has been stated and accepted for many years that the automotive industry was the instigator, the principal sponsor for and the largest user of alloy steel and nonferrous alloys. The only universally recognized standard specifications and heat-treatments for these materials are those adopted by the Society of Automotive Engineers. It is this same auto-motive industry that has been the chief inspiration for and consumer of modern production machine tools. The production curve of steel ingots is more sensitive to fluctuations in automotive production than any other influence or group of influences. In every other important steel-con-suming industry, automotive materials and automotive processes are the outstanding features of modern progress. In this connection I need only mention the prefabrication of buildings, following the automotive system of straight-line, interchangeable mass production; the motorization of ships and railroads, employing automotive types of prime movers; the production of pressed-steel stoves, plumbing and furniture by methods originated in the automobile-body industry and the extensive use of rubber for the cushioning of all manner of machinery as pioneered by the automotive and tire industries. Dr. Jeffries has brought out this point in his address (p. 21), assuring us that the transportation industry is the largest user of these materials. In the transportation industry, or as we might more accurately express it, the transportation group of industries, the. automotive industry pre-dominates as a user of light alloys. One out of every four tons of aluminum produced is consumed by the automotive industry. Similarly, the automotive industry ranks first in the consumption of the following metallurgical materials: steel, 24.04 per cent; malleable iron, .57; alloy steels, 72.2; nickel, 30; lead, 39 per cent.

Jan 1, 1936

By B. D. Cullity

INTRODUCTION THIS investigation of bismuth-selenium alloys was made in an attempt to find a suitable material for use in thermoelectric generators. These devices are simply thermocouple circuits designed for the efficient production of electrical energy from thermal energy, which may in turn be derived directly from solar radiation or from the combustion of fuels. The requirements of a material for use in a thermoelectric generator are obviously quite different from those of a material used in a temperature-measuring thermocouple. Naturally, for power generating purposes, the thermoelectric power (voltage produced per degree difference in temperature between the junctions) must be as high as possible. Furthermore, in order to obtain reasonably high power outputs, the materials used in the generator must have an electrical conductivity which is as high as possible. Finally, in order to minimize heat lost by conduction to the cold junction, the thermal conductivity must be as low as possible. The relation between these several factors and the efficiency of conversion of thermal into electrical energy-the thermoelectric efficiency-has been discussed by Telkes1 in a recent review of the subject. She gives the thermoelectric efficiency as: [ ] For many materials, some of the desired properties (for example, high electrical and low thermal conductivity) are almost mutually exclusive; the problem thus becomes one of finding a material which has the optimum combination of properties. BISMUTH-SELENIUM ALLOYS Work on the equilibrium diagram of the bismuth-selenium alloys has been reviewed by Hanson,2 who gives the diagram reproduced in Fig I. There are two intermediate phases in this system, BiSe and Bi2Se3. The existence of an alpha and beta modification of BiSe has not been demonstrated satisfactorily and the writer found no evidence of it in the present work. BiSe and Bi2Se3 have, like bismuth, a rhombohedral crystal

Jan 1, 1948

By Julianne H. Glarmaty, Peter J. Conroy

INTRODUCTION In 1970 the percentage of underground coal extraction by longwall mining methods in the U.S. was 2.1 percent. This figure rose to 4.4 percent in 1976 and is expected to rise to 12 percent by the year 1985. This figure represents 46.0 million tons (51.0 million st) of annual production (Kuti, 1978). In addition, OSM regulations are placing emphasis on subsidence prediction. Section 784.20 of the Office of Surface Mining regulations for underground mining permit applications requires the sutauission of a subsidence control plan which may include monitoring. Because of its nature, longwall mining does not have flexibility in leaving pillars under structures as does room and pillar. Mining in some areas, particularly in the Eastern Coal Field, is approaching more developed areas; therefore, a greater number of structures are expected to be undermined in the near future. Subsidence engineering is becoming an important aspect of mine planning, and should be directed at predicting potential structural damage. The question operators are increasingly faced with is "what will be the subsidence effects for a specific structure at a specific location in respect to a longwall panel?" The most significant variable in assessing the subsidence effect on structures is not vertical subsidence. The variables of strain and tilt are responsible for more structural damage than is the vertical movement. Table I presents threshold values of strain for various structures (Geddes 6 Cooper, 1962). Based on National Coal Board experience, horizontal strain is approximately inversely proportional to the radius of curvature of a circular portion of a subsidence profile; therefore, the radius may be useful in estimating the magnitude of strain caused by subsidence (Hoebs, 1982). The radius of curvature can be determined by the following equation:

Jan 1, 1982

By Theodore Holt

Outline of the Process THE Mines Operating Co.'s plant at Park City, Utah, was designed to treat the low-grade fillings in the old stopes of the Ontario mine. These fillings carry 6 to 14 oz. of silver, 1 to 2 lb. copper, 0.01 to 0.015 oz. of gold, and a small percentage of lead and zinc. The treatment consists in mixing the crushed ore with coal dust and salt and then roasting in a new type of furnace y combustion of the contained fuel. The roasted ore is leached with an acid salt solution to dissolve the silver, gold, copper, and lead. At present these metals are precipitated together on scrap iron and the product sold to a refinery. The only new feature of importance in this scheme of treatment is the roasting process, which makes possible the chloridizing of ores without any loss of the valuable metals, and at a very low cost. History of the Development of the Process The roasting process had its beginning in connection with research work at the Utah State School of Mines. N. C. Christensen, Jr., who held one of the School of Mines' fellowships, was engaged in some experimental work on blast roasting. At the same time I was doing some work on the insoluble gold in Mercur base ores. Mr. Christensen roasted some of this base gold ore in his pot furnace, and found that when he mixed a sufficiently low percentage of fuel with the ore, it did not sinter but roasted to a leachable product. We considered this a new application of blast roasting, and proceeded to test out a large number of ores in several different types of small roasters which we constructed. This experimental work continued well into the summer of 1911.

Jan 7, 1914

By John L. Schroder, D. L. McElroy

ALTHOUGH the earliest use of rubber-tired haulage was in Illinois in 1936, the first unit of this type of equipment used in West Virginia was shipped into the state in 1938. All units placed in West Virginia mines have been of the shuttle-car type. The Katherine Coal Mining Co., at Lumberport, W. Va., was the second company in the United States to install shuttle cars and the Gay Coal and' Coke Co., at [ ] Mt. Gay, W. Va., was the first company in the country to install the thin-bed type of shuttle car. On Oct. 8, 1940, nine companies in the state were using 41 shuttle cars, of which 10 cars at three mines were of the thin-bed type. All shuttle cars of the low type were in the southern fields and all of the high type were in northern West Virginia. At that time several units were in the process of delivery. The data in this paper were collected in the field by Mr. Schroder in connection with graduate work on mechanical loading of coal in West Virginia by mobile loaders. In the course of his field work he visited five mines in the state that were using shuttle cars. All of these mines were in high-volatile coal beds of strong structure. [ ] The more pertinent data obtained at the mines visited are given in Table I. The maximum distance of shuttle-car haul is the distance between the transfer station and the farthermost place. Tonnage per loading unit per foot of bed thickness is to some degree a measure of relative efficiency, especially if the different operations are working the same bed or have somewhat similar conditions. The thin-bed operation is well up in the higher bracket of the afore-mentioned column, which is as

Jan 1, 1941

By T. B. Crowe

MucH has been written upon the precipitation of metals from cyanide Solution by zinc. We often read of the many factors that influence precipitation, such as zinc surface, purity of zinc, percentage of lead, temperature of solutions, strength of solutions in cyanide or alkali, etc. -Little do, we hear, however, of the part that oxygen plays in precipitation. Caldecottl says: "As the dissolving of gold is essentially an oxidation process, so its precipitation is one of reduction." All who have studied or worked with cyanide solutions will agree that Caldecott's statement is true.' . In the cyanide work in the mills of the Portland Gold Mining Co., we have always found oxygen to be the greatest enemy to precipitation. Oxygen Antagonistic to Good Precipitation A few years ago, while making some experiments on the effect of pressure upon the dissolving rate of gold from our ores, to prove a point, I made some bottle tests under vacuum. The results were surprising, and showed that under vacuum practically no gold dissolved, which confirmed my belief that Elsner's equation was true and also led me to investigate the amount of dissolved air carried by solutions at atmospheric pressure. The experiment consisted in partly filling an acid-bottle with mill-solution and connecting it by a rubber hose to a vacuum pump. When the vacuum was suddenly applied, a cloud composed of thousands of small air bubbles rose out of the solution, showing qualitatvcily' the amount of dissolved air that was contained in the solution, and also proving that the relief of atmospheric pressure on the solution permitted this dissolved air to escape. In studying literature on the subject, we find Henry's law—"The amount of gas dissolved by a liquid is proportional to the pressure to which the gas is subjected."

Jan 1, 1919

By W. Denham Verschoyle

In designing a pocket instrumeut whereby any giver1 horizontal or vertical angle may be closely approximated, the following points should be kept in view, if general utility is aimed at : 1. The instrnment should be light and compact, so that it can be carried in the pocket, or in a sling. 2. It should be capable of observing any angle whatever, horizontal or vertical. 3. Since time is often an important consideration in making a preliminary survey, it should be capable of giving the horizontal and vertical angle at one observation. I do not know of any instrunlent that will fulfill these requirements, except the one here described. Where the depression- or elevation-angle of the distant object, whose bearing is required, exceeds 50 or 60 degrees, it becomes difficult or impossible with a prismatic compass, for instance, to obtain accurate results; and since it frequently happens, particularly in mining, that much work requires to be done beyond that limit, it is obvious that an instrument which can be used to observe a high angle just as easily as a low one, if not absolutely a necessity, will at least be a great convenience. How this a pocket transit" attains to the required degree of universality will be understood from the diagram, Fig. 1, in which B is a beveled, graduated circle, attached to and freely revolving about the center of the magnet A. Light falling on B is reflected through a window in F (the compass-box), along the line AC, and is again reflected back to the eye at D by the prism C. By a simple arrangement, the tight-line BCE call be completely revolved in the vertical plane DE, which is normal to AC. It is clear, then, that no matter through what vertical

Jan 1, 1908

By J. M. Hartman

ONE of the most important subjects to the blast-furnace engineer is a thorough knowledge of the conditions affecting the temperature in the different portions of the furnace. All efforts to decrease the consumption of fuel and improve the working of the furnace must be based upon it, and I may, therefore, be permitted to place before you the results of my observations, and detail the conclusions to which they have led me. Tracing the thermic conditions from below upwards we have at the bottom of a blast furnace making No. 3 iron a temperature of 2900° F., which increases slightly to a point a little below the tuyeres. In the immediate vicinity of the tuyeres the temperature is somewhat lower, owing to the entering blast ; but a short distance above the tuyeres, where all the oxygen of the blast has been converted into carbonic acid, the highest temperature in the furnace must be attained. This carbonic acid is, however, almost as soon as formed, converted by the glowing coal into carbonic oxide, a process which absorbs heat, reduces the temperature, and provides the active agent for the reduction of the iron ores. In its ascent the hot carbonic oxide gradually parts with its heat, first melting the descending iron and earthy materials, which drop down to the hearth of the furnace. The limit of this zone of fusion is rather sharply defined, and the temperature above this zone suddenly decreases. In its further ascent the hot gas drives off the carbonic acid from the limestone, which causes a further absorption of heat, and finally the gas escapes at the top, at a temperature of about 250° F. if the furnace is working well. These changes of temperature 1 have attempted to represent graphically,

Jan 1, 1880

J. L. JONES,* Pittsburgh, Pa.-If a nickel anode is cast under commer-cial conditions, will it contain nickel oxide? Will the nickel oxide affect the rate of corrosion in a double sulfate solution; or will the nickel oxide dissolve in a double sulfate solution? I would also like to ask whether a 98 per cent. pure nickel anode will corrode as fast as a 96 per cent. nickel anode; whether electrolytic nickel will corrode less rapidly than nickel containing a small amount of carbon; and whether the materials some-times used in coating molds for casting nickel anodes will affect the rate of corrosion of the anode? In other words, whether an electrically non conducting coating is likely to be present that will prevent the nickel anode from corroding rapidly. JOHN F. THOMPSON.-The nickel oxide will not dissolve in the double sulfate solution, as far as we know. We do not make the ordinary nickel anode of commerce, but we supply nickel to the nickel anode makers. Those makers almost invariably buy a high-carbon nickel shot, ranging around 0.45 per cent. carbon. In their process, they even further, car-burize it so as to get nickel that will melt easily and be fluid enough to fill the mold, so that the ordinary cast anode on the market is unquestion-ably oxide free. The only time that such an anode will have oxide will be through an error in melting. Some cupola makers of anodes have had trouble with oxidation, but as a rule the anodes are thoroughly carburized; so much so that they probably carry a couple of per cent. of carbon of which around. 1.6 per cent. is graphite.

Jan 12, 1919

By Utley Wedge

In general, the art of securing copper from sulphide ores or concentrates may be said to consist of: (1) separation, in the molten state, of copper sulphide with some iron sulphide, from the great bulk of gangue-material, followed by (2) elimination of sulphur and iron from the molten matte, by oxidation and fluxing, leaving metallic copper. The definition is made broad enough to cover the general practice, whether or not the ore or concentrate is given a prelimiuary roast for the removal of surplus sulphur. The above process, which I will designate as the smelting process, makes necessary the presence in the ore, or the addition thereto, of such silica, lime, and iron as may be necessary for the formation of a light and fusible slag, together with sufficient sulphur and iron for the formation of copper-matte, and also the addition to the matte of sufficient silica for the oxidation and fluxing-out of the iron. These items, together with the cost of fuel sufficient for melting the mass, constitute important items of cost in the copper-smelting process. Numerous cases where fluxing-materials are scarce or dear, or where fuel is expensive, have caused special attention to be given recently to the wet process of copper-extraction, which may be designated as consisting of forming soluble copper salts which are then washed or leached out of the ore or concentrates by dissolving in water or acid. Metallic copper may then be secured from the solution of copper salts by electrolysis; by cementation; or copper can be brought out of the solution as a hydroxide or other insoluble precipitate and reduced to metallic copper by subsequent melting in a reducing atmosphere.

Jan 1, 1913

By J. B. Umpleby

The subject of reservoir energy and its efficient utilization has been well explored in many papers. The present effort, therefore, is limited to a summary of existing information combined with an emphasis of the probability that the relative importance of controlling factors will change with advancing knowledge. Consequently the necessity for flexibility in laws and regulations, inherent in the problem, is emphasized. Definitions Many terms have been widely used in the literature without having been specifically defined. For example, confusion exists in the use of ((reservoir energy" and "gas energy." The latter is much more limited in meaning than the former. Other terms have been variously used. Consequently, I shall preface my remarks with definitions of a few of the more pertinent terms. Reservoir energy is that force or forces, active or potential, that is native to the reservoir and has the power to move oil through the reservoir rock. The energy may result from expanding gas, from hydrostatic head, from the weight of overburden, or from any other source. Gas energy is the expansive power of gas when pressure is reduced. It is one type of reservoir energy. An oil reservoir is that part of a geologic formation or formations in which oil occurs in commercial quantities wholly surrounded by nonproductive rock. The essence of this definition is effective separation rather than remoteness and under it oil reservoirs may be superimposed in the same oil pool. Conservation of reservoir energy means primarily its maximum use in the production of oil. Unit operation is a plan of development and production, which embraces an entire oil reservoir under a unity of engineering control. It is distinct from unitization, which has to do with arrangements of organization and equities to make unit operation possible in areas of divided ownership.

Jan 1, 1934

By R. L. Fleischer

IN 1925 a criterion for localized deformation in a single crystal was derived by Taylor and Elam.' They noted that for a single active slip plane the slip plane area is constant, but the direction of the stress with respect to the slip direction changes during deformation so that, when the increase in stress due to this rotation is large enough relative to the work hardening, instability occurs. (By instability is meant continued slip on the active slip plane.) The instability criterion may be written t>dt/d?/m tan2? [1] where t and ? are resolved shear stress and strain, m the Schmid factor for resolving shear stress, and ? is the angle between the slip direction and the axis of tension. The formula points out that regardless of the atomic mechanism involved, for large flow stresses and low work hardening rates, slip on a single plane—once started—should continue. The case of alloying provides a direct possibility of adjusting the parameters in Eq. [I]: As an alloying element is added to a pure metal, the flow stress is raised and the work hardening in easy glide may be either decreased2 or unaltered.3 Since flow stresses in easy glide may rise to the kg/mm2 range for alloy crystals while easy glide slopes may be less than % kg/mm2, 2 it is possible for the inequality to be satisfied. Indeed Garstone and Honeycombe3 report that slip becomes coarser with increasing stress in the easy glide range, where the flow stress would be increasing and the slope would be essentially constant. Another case where high flow stresses and low hardening rates accompany coarse slip is that of quench hardening.4 Maddin and Cottrell report that quenched aluminum crystals display slip markings resembling those of a brass. A similar effect has been observed after irradiation.'

Jan 1, 1960