Search Documents

By Thomas Fraser, David R. Mitchell

THE primary purpose of the loading plant is to transfer the finished product from the preparation machines to the railroad car, truck, or barge in which it is to go to market. Secondary purposes of the loading plant are: to prevent excessive degradation of sizes during loading, to reduce segregation as much as possible, and to prevent excessive quantities of very good or off-grade coal from entering any one car. Nonuniformity of consignments is one of the chief sources of complaints by consumers and coal merchants. A properly designed loading plant will do much to reduce complaints and insure uniformity, not only from shipment to shipment but also in each individual consignment along the length of the car and in cross section. DEGRADATION IN STORAGE, LOADING AND SHIPMENT The object in loading is not only to handle the coal without breakage and segregation, but also to produce a well-trimmed load that will ride to its destination without spillage o~ breakage en route. The small sizes present in a car-of prepared coal as received by the purchaser consist of: missed small sizes not screened out in the preparation plant, breakage during loading, and breakage caused by handling en route. For domestic sizes of anthracite shipped from the Pennsylvania anthracite field to Atlantic coast cities, the dealers' loss because of breakage in loading and shipment amounts to from 2 to 5 per cent and for anthracite shipped to Middle West cities, the loss is 8 to 9 per cent. This difference is in part because dealers in the Middle West rescreen their coal more thoroughly than is usual in the East. One dealer handling Illinois No. 6 coal shipped from southern Illinois mines to Chicago reports an average size loss of 10 per cent when lump coal is unloaded with a fork. This runs as low as 5 per cent for carefully loaded coal and as high as 15 per cent for carelessly loaded coal. An Ohio dealer estimates the degradation in loading and shipment of West Virginia coals consigned to Ohio cities as follows: Pocahontas lump

Jan 1, 1950

By J. A. Herbst, G. E. Agar

The effect of fluid viscosity on the classification of solids in a liquid-solid cyclone was investigated. The separation size was found to be proportional to Additionally, it was found that the prediction of flow rate through a cyclone is dependent on a Reynolds criterion. Above a critical value, the flow can be predicted by a simple equation, whereas, below this value a variable orifice coefficient must be introduced. INTRODUCTION The solid-liquid cyclone is widely used as a device for classification, thickening, and heavy media separations. The more important variables and how they affect the performance of a cyclone are known and have been the subject of several investigations.' In general, these studies have paid little attention to the viscosity and those which have, introduced it through Stokes settling considerations. Systems which contain appreciable amounts of swelling clays exhibit viscosities much greater than water, and in these systems the viscosity term becomes important in determining the separation size. The work described here was done to determine in a Newtonian system the dependence of separation size on viscosity. BACKGROUND The separation size for a cyclone classifier has been related to the parameters of the cyclone by an equation of the form: where a is probably between 1.3 and 1.5, ß is between 0.50 and 0.57, and 6 has a theoretical value of 0.5. where y has a value between 1.8 and 2.0. Although these relationships are empirical, equations that differ only in the exponents have been derived from theoretical considerations. Those interested in the origin of these equations are referred to some of the original work.6,7 MATERIALS AND PROCEDURE The laboratory apparatus used in this study is pictured diagramatically in Fig. 1. Feed slurry was pumped from an agitated 15-gallon plastic tank by a centrifugal pump driven by 3/4 hp motor. The static pressure of the feedstream and thus the pressure drop through the cyclone was measured on a gage located as close to inlet of the cyclone as possible. When samples were not being taken, overflow and

Jan 1, 1967

By Paul A. Farrar, Felix Ermains, Harold Margolin

The systems Ti-Crand Ti-Vhave been reinvesti-gated in the region up to 40 wt pct alloying addition using both conventional and rapid quenching techniques. The Ti-Cr eutectoid temperature was determined to be at 667° & 10° C and 14.5 wt pct Cr. The solubility of the Cr in a Ti was found to be less than 1 pctat 700"C. The P transus of the Ti-V system was found to be depressed to 510°C at 40 wt pct V and the solubility of V in a Ti was found to be less than 2 wt pct at 700°C. Investigation by a. d. McQuillan1-3and m. k. McQuillan4 on the systems Ti-Co, Ti-Cr, Ti-Cu, Ti-Fe, Ti-Mn, Ti-Ni, and Ti-V has cast doubt as to the position of the ß/a + ß boundaries in many of these systems. Their investigations were carried out using hydrogen pressure and/or rapid quenching experiments, as opposed to the conventional quartz capsule techniques employed by most other investigator.'" By these methods, the ß/a + ß boundary was found to be lower than that obtained by conventional techniques in all except the Ti-Fe system. In the latter, the ß/a + ß boundary was essentially the same as the boundary obtained by conventional technique.7' On the basis of rapid quenching results in the Ti-Cr system, M. K. McQuillan4 placed the eutectoid temperature below 550°C whereas other investigations using conventional techniques had placed the eutectoid variously as between 650' and 700°C,5 between 675' and 700°C,6 between 650" and 675°C,7 at 670°C,8 and above 625"C.la9l3 In order to check these results, a reinvestigation of four of the systems was undertaken using both conventional and rapid-quenching techniques. The Ti-Fe and Ti-Mn systems will be dealt with in anoth er paper, with only the Ti-Cr and Ti-V systems being discussed here. EXPERIMENTAL TECHNIQUES Alloys employed for the delineation of the systems under investigation were prepared from iodide titanium sheet capsules containing the alloying materials,

Jan 1, 1962

By Harry Klemic

Zirconium and hafnium minerals are used industrially both as minerals valuable for their chemical and physical characteristics and as ores of zirconium and hafnium. The principal zirconium-hafnium-bearing minerals, their composition, and their ranges in content of zirconium and hafnium dioxides are listed in Table 1. The supply of zirconium and hafnium is based almost entirely upon the supply of the minerals zircon and baddeleyite. Eudialyte may eventually also be of importance as a source of these elements. Zircon, which generally contains nearly 49% zirconium and between 0.4 and 1.5% hafnium, is the principal industrial mineral of this group. Baddeleyite, a commercially important but less abundant mineral, contains as much as 73% zirconium and 0.4 to 1.7% hafnium. Eudialyte has a wide range in content of these elements, but analyses of material from several localities indicate values of 6 to 11 % zirconium and 0.07 to 0.4% hafnium. Zircon is a mineral consisting principally of zirconium, silicon, and oxygen that crystallizes from magmas during the formation of igneous rocks. Zircon also occurs in veins and in metamorphic rocks. It is in the tetragonal crystal system. It commonly forms as small well-developed prisms having pyramidal terminations but also occurs as irregular-shaped grains. Zircon has a hardness of 7.5 on the Mohs' scale. Its specific gravity is commonly between 4.68 and 4.70 (Dana, 1932), but the specific gravity varies somewhat depending upon com- position and state of alteration. Zircon has no good cleavage directions and is brittle, breaking with a conchoidal fracture. Zircon of the composition ZrSiO, would contain 67.2% Zr02 and 32.8% SiO2. However, in addition to about 1 % of hafnium, minor amounts of thorium, uranium, rare earth elements, yttrium, calcium, magnesium, iron, aluminum, phosphorus, and hydrogen, and trace amounts of other elements are commonly present in the mineral (Frondel, 1957). Radiogenic lead and other daughter products from the radioactive decay of uranium and thorium also accrue in the mineral. Radiation damage to the structure of zircons that contain appreciable amounts of uranium and thorium may alter the internal structure of the crystals to

Jan 1, 1975

By P. R. Bradley

The property of the Alaska Juneau Gold Mining Co., covering the Juneau gold belt for over a mile in length, consists of 136 claims and 24 mill sites; these are near Juneau, Alaska, in what is known as the Harris mining district. Gold was discovered in the district in 1880, by Richard T. Harris and Joseph Juneau, who had been prompted to explore the section by rumors they had heard among the Indians. Gold was first found on the beach at the mouth of Gold Creek and further search revealed the lode deposits in the Silver Bow basin, about two miles inland. The lode locations made immediately thereafter constitute the principal area of the Alaska Juneau group of claims. Gradually news of the strike spread and, during the late eighties, Silver Bow basin became a substantial producer of gold, both from placer work and from quartz milling. Numerous small mills of various types were erected to crush high-grade float and stringers gouged to shallow depths. Placer mining gradually ceased and the pioneer milling operations gave way to larger and better mills, which in time were the predecessors of the two large mills built by the Alaska Gastineau Co. and the Alaska Juneau Co. on the shores of Gastineau Channel. This evolution from arrastres to small mechanical mills, thence to the two large-capacity mills on Gastineau Channel, although a natural sequence of events, had a most important bearing on the development of the district. Knowledge of the character, extent, and value of the ore deposits gained by these early operations could not have been acquired otherwise. Spencer shows1 that the early mills were: Arrastres in 1881-82-83-84-85-86-88; a 5-stamp mill in 1882; a "newly devised grinding mill" in 1884; two Huntington mills in 1886; a 10-stamp mill in 1889; a revolving Dodge mill in 1890; a 5-stamp mill in 1891; and a 20-stamp mill in 1893. He also estimates the gold production to the end of 1893 as $1,000,000 from lode mining and $1,250,000 from placer mining. No estimate can

Jan 1, 1925

By H. R. Hanley, D. F. Walsh, C. Y. Clayton

Lead-refining practice at the Bunker Hill differs to some extent from that of other United States refineries using the Parkes process, in that the Bunker Hill has reverted to a custom used years ago of making two kinds of skims, or crusts, in the desilverizing kettles. Also, this was the first refinery to adopt the liquation process for silver skims as developed in Australia. Both of these ideas were brought to the attention of the operator by H. S. J. Sommerset, in the summer of 1924, while he was visiting metallurgical plants in the United States, when he was general superintendent of the Broken Hill Associated Smelters Pty., Ltd., of Port Pirie, South Australia. Since Mr. Sommerset's visit, United States patents on the liquation process have been issued to George Kenneth Williams, of Port Pirie, South Australia. At the Bunker Hill, the lead bullion is conveyed from the blast furnaces to the refinery in brick-lined cast-steel pots, each having a capacity of 5 tons, by a 20-ton electric crane, to which is suspended a Fairbanks-Morse suspension-type scale on which the gross, tare and net weights are obtained. The bullion is poured from the small bullion pots into either one of two kettles of 105 tons capacity, and when a kettle is entirely filled the heavy dross is removed by skimming it into a 5-ton pot suspended by the crane. The crane operator becomes proficient in the manipulation and a kettle is skimmed in a very short time. After the kettle is skimmed clean the bullion is pumped to a kettle of the same size alongside, where the bullion is cooled until it has almost frozen. By using two kettles for the drossing operation, one to accumulate the bullion where the heavy dross is removed, and then pumping to a clean kettle comparatively free of hangings, etc., it is possible to reduce the copper content much lower than if only one kettle is used in the operation. The average yearly analysis of bullion is given in Table 1. During July, August, September, and October, when a considerable quantity of high-grade silver ore from the Yukon Territory is smelted,

Jan 1, 1930

By G. E. Steudel

The study of the possibility of effecting a lower cost in the manufacture of pig iron reveals the importance of the ever present question of slag chemistry and volume. Factors that determine slag chemistry and volume are the impurities in the ore available, the ash-sulphur content of the coke, and a flux material necessary to promote removal of sulphur. Of these, the ores present by far the major source of impurities and what may prove to be the lowest practical slag volume with desired chemistry in one locality may be considered low or high in some other center of iron manufacture. The Chicago district is not only blessed with ores of high quality, but with excellent coke and flux materials as well. It is the intent of this paper to discuss slag problems at the South Works only, where burdens consist of Mesabi ores, Michigan stone, and coke ranging from 7 to 9 per cent ash and containing an average of 0.57 per cent sulphur. Early in the development of modern blast-furnace practice, the consideration of slags was secondary to the many adjustments of mechanical difficulties, such as furnace lines, stock distribution, stove design for obtaining higher blast temperatures, improved chemical segregation and size of raw materials. Furnace operators, after making these improvements, turned their attention to the study of other refinements in practice, of which slag chemistry appeared to be the most important. It is only within the last two decades that operators have become familiar with the various aspects of slag compositions. The industry, while rather slow in its recognition, is indebted to such investigators as Rankin,1 Wright,1 Feild,2 Royster,2 McCaffery,3 Kinney,4 Holbrook,5 and Joseph,5 whose researches concerning the elimination of sulphur within the blast furnace and the effect of slag composition upon melting point, viscosity, and desulphurizing power have established criteria for the selection of slags of the requisite quality. Large slag volumes result in higher coke consumption and cost of disposal. Any attempt to lower slag quantity must be accomplished

Jan 1, 1940

By G. E. Steudel

The study of the possibility of effecting a lower cost in the manufacture of pig iron reveals the importance of the ever present question of slag chemistry and volume. Factors that determine slag chemistry and volume are the impurities in the ore available, the ash-sulphur content of the coke, and a flux material necessary to promote removal of sulphur. Of these, the ores present by far the major source of impurities and what may prove to be the lowest practical slag volume with desired chemistry in one locality may be considered low or high in some other center of iron manufacture. The Chicago district is not only blessed with ores of high quality, but with excellent coke and flux materials as well. It is the intent of this paper to discuss slag problems at the South Works only, where burdens consist of Mesabi ores, Michigan stone, and coke ranging from 7 to 9 per cent ash and containing an average of 0.57 per cent sulphur. Early in the development of modern blast-furnace practice, the consideration of slags was secondary to the many adjustments of mechanical difficulties, such as furnace lines, stock distribution, stove design for obtaining higher blast temperatures, improved chemical segregation and size of raw materials. Furnace operators, after making these improvements, turned their attention to the study of other refinements in practice, of which slag chemistry appeared to be the most important. It is only within the last two decades that operators have become familiar with the various aspects of slag compositions. The industry, while rather slow in its recognition, is indebted to such investigators as Rankin,1 Wright,1 Feild,2 Royster,2 McCaffery,3 Kinney,4 Holbrook,5 and Joseph,5 whose researches concerning the elimination of sulphur within the blast furnace and the effect of slag composition upon melting point, viscosity, and desulphurizing power have established criteria for the selection of slags of the requisite quality. Large slag volumes result in higher coke consumption and cost of disposal. Any attempt to lower slag quantity must be accomplished

Jan 1, 1940

By John McCoy, Edward Thimons, Kenneth Heller

As the working levels in domestic mines are developed to greater depths and work areas move further from the shafts, maintaining a safe and healthful working environment becomes more difficult. Increased temperature and humidity at greater depths becomes first a factor in productivity and then a threat to the miner's safety. Initially, a miner might develop listlessness leading to reduced productivity and reduced alertness. Continued overexertion can lead to heat stroke and possibly death. Mine ventilation engineers, therefore, must not only provide clean air to work areas, but also must provide cooled air. The following article describes the United States Bureau of Mines (USBM) and Foster-Miller's successful development of a high performance, low maintenance direct water to air contact heat exchanger for mine cooling. While heat problems frequently do not develop until mining operations descend below sea level, problems will arise any time mining penetrates high temperature rock. Hot fissure water will increase the severity of the situation, causing increases in wet bulb temperature - the temperature to which perspiring miners reject metabolic body heat. All energy expended in mining adds to the heat load which must be absorbed by the ventilation air. Just when the cooling capacity of ventilation air is needed most, adiabatic compression (autocompression) of air descending the shaft raises air temperatures 1.3g°C (2.5'F) to 2.94"C (5.3OF)/305m (1000 ft) depending on humidity. Increased temperatures decrease the ability of the air to absorb heat from the mine, and work area temperatures rise. Once forced ventilation air can no longer maintain safe work area temperatures, refrigeration methods must be employed. Many mines now use cooling coils for this purpose. A cooling coil uses refrigerated mine water to cool the air by passing the air through banks of copper tubing filled with cold water. Heat from the air is transferred to the water through the pipe with the aid of fins. Conventional water to air heat exchangers prove troublesome for many mines be- cause of the high levels of dust that are encountered, causing these exchangers to operate at relatively low efficiencies. A more satisfactory approach to work- place cooling is desired - one that offers reduced maintenance and increased cooling efficiency.

Jan 1, 1982

By E. Luttgen

The substance referred to in the title is the artificially prepared basic carbonate of magnesia, a compound of the carbonate with the hydroxide. It is the "block-magnesia " of commerce, the magnesia alba of the pharmacist. Its composition, though somewhat indefinite, may usually be expressed by the formula : 4MgCO3,Mg(OH)2, 5H2O; it is found to vary slightly with the details of the method of preparation. This substance has been employed recently with much reported success, as a non-conductor of heat. It is moulded to form coverings suitable for steam-pipes and their fittings and sectional jackets for boilers and cylinders; it is furnished also in forms suitable for lining refrigerators, walls and roofs of buildings, fire-proof safes, etc. It was with a view of ascertaining the efficiency of this material as a non-conductor, or, rather, its relative efficiency among the various non-conducting materials in use, that the writer made the experiments about to be described. A block of magnesium carbonate or magnesia alba exhibits some interesting physical qualities. It is a smooth, white, close-grained solid, in outward appearance resembling a block of Paris plaster. It possesses the lightness of cork, the porosity of sponge, and withal a degree of firmness and strength that, in view of its levity, is quite remarkable. To examine more closely the properties of this substance, a number of 1-inch cubes were sawed from the commercial block-carbonate, also some bricks, that is, blocks measuring accurately 2 x 4 x 8 inches, the dimensions of an ordinary brick. The cubes weighed from 2.2 to 2.7 grammes, the bricks weighed 140 to 175 grammes (5 to 6 ounces). The bricks were carefully measured and weighed, and placed in vessels containing distilled water, in which they became gradually submerged, owing to the displacement by water of the air inclosed in the structure of the magnesium carbonate. After twenty-four hours the blocks were removed from the water, dried superficially by contact with filter-paper and weighed. From the increase in weight, the volume of the water absorbed, and consequently that of the air displaced by it, were obtained. For example: a block which when dry weighed 155

Jan 1, 1887

By W. G. Woolnough

Production of oil in Australia is negligible at present. A very small quantity of crude is being recovered from lean pumpers in Victoria, and a little activity is evidenced in Queensland, where two new wells were sunk during 1934. One of these, at Warooby Creek near Roma, obtained a noteworthy gas flow, but no oil production has been recorded. Geological investigation is going on in Western Australia, but no drilling activity is apparent. The "boom" in oil prospecting came to an end when the wave of depression swept over the country, and the investing public turned its attention actively towards gold. There is great activity in gold prospecting at present. I still maintain as strongly as ever that the prospects of obtaining flow oil in Queensland, Western Australia and Victoria are good, and that really scientific methods must ultimately succeed. Active and excellent geological work is being carried out in the Mandated Territory of New Guinea, and it is reported that drilling is likely to be undertaken next year. Matters in Papua are at a standstill. The question of extraction of oil from the oil shales of New South Wales and Tasmania is perennially active, and attempts to exploit this source commercially are renewed from time to time. Hydrogenation of coal is also receiving a good deal of attention.

Jan 1, 1935

IT is a pleasure for the translators to record their gratitude to the Seeley W. Mudd Memorial Fund of the American Institute of Mining and Metallurgical Engineers for underwriting the cost of publication of this volume, to the Printing-Office of the Yale University Press for doing an unusually fine printing job, and to the following for granting permission to reproduce the title pages of volumes in their collection: The Bibliothèque Nationale of Paris, for edition A of the Bergbüchlein; the Osler Library of McGill University, Montreal, for editions B and G of the Bergbüchlein and edition D of the Probierbüchlein; Mr. Herbert Hoover, Jr., for editions C and E of the Bergbüchlein and editions E, M, N, and 0 of the Probierbüchlein; the Parsons Collection of the Reference Department of The New York Public Library, for edition D of the Bergbüchlein; the Library of the Bergakademie Freiberg, for edition F of the Bergbüchlein and editions A, H, and L of the Probierbüchlein; the Herzog August-Bibliothek of Wolfenbüttel, for edition C of the Probierbüchlein; the British Museum. Library, London, for edition I of the Probierbüchlein; and the library of the University of California at Berkeley, for edition J of the Probierbüchlein. The cooperation of those who helped with the translation of the Bergbüchlein is acknowledged on p. 64. A. G. S. C. S. S.

Jan 1, 1949

By F. L. Grammer

In these day, when anthracite is less extensively used as a blastifurnace fuel than it was a generation ago, and managers endeavor to maintain regular and known ore-mixtures, the " freezing " of tuyeres, cinder-notch or iron-notch is infrequeut; and, consequently, the oil-burner or " kerosene blowpipe "* is seldom employed; and furnace-foremen have, to a considerable degree, forgotten their former cunning and persistency in the use of the drill and sledge. Still, in starting new or abandoned plants with untrained labor, and in running some of our large 100-ft. furnaces, slips, resulting in very cold furnaces, may occur, even under experienced managers. During my superintendence of the Cleveland, O., blast-furnaces, such a misfortune, owing to a dearth of trustworthy foremen, was experienced; and our electrician, Mr. Thomas Martin, proposed to open the tuyeres and cinder-notch by means of the heat of the electric arc. We have heard that the surface-cracks or marks developed in rolling heavy plates have been closed by electric welding, as by a soldering-iron, and also that an electric burner has been employed at some German blast-furnaces; but the experiment was quite novel to us; and I think it constituted one of the first, if not the very first, successful application of this device, for the purpose named, in the United States. †

Jan 1, 1902

The Institute conducts jointly with the American Society of Civil Engineers, 'American Society of Mechanical Engineers and American Institute of Electrical Engineers, certain activities as listed below, and is joint owner with them if certain properties. United Engineering. Trustees, Inc. When Mr. Carnegie made his gift which made possible a home for the engineering societies, a separate corporation was organized to act as a holding company and to manage the common property. This was long known as the United Engineering Society but the name has now been changed to one which more nearly reflects the real function of the corporation. It holds title to the Engineering societies Building and to various funds placed in its charge and is managed by a Board of Trustees of which three are chosen by each of the four societies, American Institute of Mining and Metallurgical Engineers, American Society of Mechanical Engineers, American Institute of Electrical Engineers and American Society of Civil Engineers, which own equal and undivided interests in the property. The land and building cost two million dollars. The interest of each of the Founders societies, aside from especial trust funds, is now valued at $493,352. The A. I. M. E. trustees are Arthur S. Dwight, J. V. N. Don and George D. Barron. The President of the Board is Francis Lee Stuart and the Secretary, Alfred D. Flinn.

Jan 1, 1929

The following is an incomplete list of members and guests who' called at Institute headquarters during the period Mar. 10, 1918 to Apr. 10, 1918. W. Sinclair Brown, Lebong Donok, Sumatra. F. Laroque, Roodepoort, Transvaal. H. B. Catlin, Syracuse, N. Y. A. H. Means, Camp Upton. A. R. Chambers, New Glasgow, Nova Scotia. J. H. Miles, Nome, Alaska. W. M. Corse, Buffalo, N. 1 . Harvey S. Mudd, Washington, D. C. George C. Crossley, Toms River, N. J. Henry Noyes, Melbourne, Aust. F. A. Dalburg, Montoursville, Pa. C. L. Petzel, Camp Upton. Kuno Doerr, El Paso, Tex. J. L. Schueler, Peoria, I11. V. E. Edwards, Worcester, Mass. J. G. Scrugham, Reno, Nev. H. F. E. Gamm, Rutherford, N. J. Frank M. Smith, East Helena, Mont. J. W. Gerhard, St. Louis, Mo. W. G. Swart, Duluth, Minn. Julius H. Gillis, Sudbury, Ont., Canada. A. L. Sweetser, Boston, Mass. S. J. Gormly, Guayacan, Chile. W. N. Thayer, Cincinnati, Ohio. Fletcher Hamilton, San Francisco, Cal. Felix E. Wormser, Cornucopia, Ore. Dorsey A. Lyon, Washington,. D. C. John B. Arnold has opened offices at 606 Lyceum Bldg., Duluth, Minn. E. E. Barker, formerly mine superintendent with the Chile Exploration Company at Chuquicamata, Chile, has resigned his position to become superintendent of mines for the Cerro de Pasco Copper Corporation at Cerro de Pasco, Peru.

Jan 5, 1918

By J. S. Kirkaldy, R. J. Brigham

AS part of a program to investigate the diffusive properties of dilute ternary austenites we have made a determination of the effect of chromium on the activity of carbon in ? iron. Samples of pure iron and Fe-Cr alloys were simultaneously equilibrated at 1000°C with atmospheres of controlled CO/CO2 ratio following the procedures of Darken and Gurry 1 and smith.' The 0.020 in. thick samples were analysed for carbon by microcombustion analyses3 to yield a set of isoacti-vity curves. The latter were converted to activity coefficient (standard state at infinite dilution) plots by combination with Smith's data2 for the activity of carbon in pure iron. Table I shows the compositions of the base alloys used while Fig. 1 shows the experimental results superimposed on a set of curves generated by the relation In?C=6.9NC- 10.7 Ne In the notation of wagner4 the interaction parameter is the second coefficient on the right, Sgr = - 10.7 This can be compared with a rather inaccurate value deduced from the transient equilibrium diffusion data of Kirkaldy et al.' as The authors are indebted to the American Iron and Steel Institute for financial support. This material is condensed from a B.Sc. Thesis submitted to Mc-Master University by R.J.B.

Jan 1, 1963

By Gilbert P. Moore

Petroleum operations in Bolivia are still limited to those of the subsidiaries of the Standard Oil Co. of New Jersey. Development work is being carried on at Sanandita and at Bermejo and testing operations in the north. Five wells have been completed at Sanandita. Wells 1 and 2 are producers, 3 and 5, which are north of 1 and 2, are poor wells, and well 4, to the south, was dry. In the Bermejo field, well 5 has just been completed. No information as to the production is obtainable. In the north one string was operated at each of the following locations: Machareti, Camatindi and Camiri. The well completed at Machareti during the year was a failure. The result of the others is not known. It is reported on good authority that a pipe line will be completed in 1931 to connect the Sanandita field with the Lomitas field in the Argentine. This will place Bolivia among the ranks of the producing countries of South America for the first time. This development indicates that some arrangement has been arrived at with the Argentine Government for the importation of Bolivian oil. During 1930 the Bolivian Government declared in effect the new Petroleum Law which had been expected for such a long time. One of the first acts of the military junta, which rose to power through a coup d'état, was to cancel this law, so that Bolivian oil operations are still under the old law of 1921. One new local company was formed to exploit 1,500,000 hectares near the town of Cochabamba. The Bolivia Concessions, Ltd., which had a concession permitting the selection of 17,000,000 acres in eastern Bolivia, is reported to have failed in 1930 and is now being liquidated. Chile During 1930 the Chilean Government entered into a contract with an individual to explore in five distinct zones of the Republic. According to the contract, geologists must be at work there by May 1 of this year and a well must be started by the end of 1931. If the operations are

Jan 1, 1931

By Andrew Corry

GEOPHYSICAL investigations based on radioactivity have been applied to the earth's crust for the purpose of discovering bodies rich in radioactive substances, or for the location of solutions with high emanation or radioactive-salt content, or for the detection of oil, which, in virtue of colloidal properties, has strong powers of radioactive absorption. RADIOACTIVE SUBSTANCES Radioactive substances are distributed in all rocks, waters, and gases in the earth's crust in small quantities. Granites and similar acidic rocks are richest in uranium and thorium, two chief radioactive substances; yet the quantities present in such rocks are of the order 10-12g., this concentration being expressed in grams per gram of the whole substance per cubic centimeter. In granites the uranium yields, according to Haddock, 3 X 10-12 g. of radium per gram of rock. In basalts the uranium yields 1.19 X 10-12 g. per gram per cubic centimeter. Of thorium the granites yield -2 X 10-5 g. per gram of rock; the basalts, 0.77 X 10-5 g. per gram. Certain series of alkalis of low atomic weight, like potassium and rubidium, show weak radioactivity; this property has no significance so far for geological research. The uranium is esti-mated indirectly from the electrical properties of one of its derivatives as a -gas (emanation) into which it is transformed. The thorium is expressed directly, though it is measured as a derivative, thorium emana-tion. There is a measure for the gaseous radium emanation, the curie, which is that quantity of radium emanation, or radon, which stands in equilibrium with 1 g. of radium. The concentration of the emanation is the Mache unit corresponding to 3.64 X 10-10 curie per liter. When gases become permeated by alpha, beta, and gamma rays, plus and minus ions are produced in them by the decomposition of neutral gas molecules, and under the influence of an electrical field these ions are given opposite motions. The measurement of the alpha rays and the bisection thicknesses of the beta and gamma rays is a means of analyzing unknown radioactive substances. These rays accompany the disintegration of radioactive substances and arise from "spontaneous internal changes

Jan 1, 1929

By V. R. Garfias, C. O. Isakson

The production of petroleum in Mexico during 1930 was approximately 39,600,000 bbl., or 5,188,000 bbl. less than in 1929. The decline which has continued for the last eight years, will place Mexico in fifth or sixth rank as an oil-producing country. The production of the northern and southern fields near Tampico declined over 5,250,000 bbl., while that of the fields in the Isthmus of Tehuantepec moderately increased. The wildcat operations which have been conducted for some years near the international border along a 290-mile belt, extending roughly 170 miles northwest and 120 miles southeast from Laredo, Texas, have so far met with little encouragement, although the oil possibilities of the region warrant the belief that commercially productive fields will be discovered eventually. An interesting development during the year was the starting of construction of the oil pipe line from Palma Sola in the South Fields near sea level—over Sierra Madre at 8660 ft.—to Atzcapotzalco, a suburb of Mexico City at an elevation of 7350 ft. This line, about 146 miles long, has a diameter of 10 in. and an estimated daily capacity of 10,000 bbl., and with its terminal refinery at Mexico City will form a transporting and refining unit which should materially affect the distribution and marketing of refined products in the Republic. Development During the past year 148 wells were drilled, as compared with 214 in 1929 and 371 in 1928, the percentage of producers being 49 as against 47 in 1929. With the exception of one well in San Isidro, at the extreme southern end of the Golden Lane, the Jardln Paso Real area was the only sector of the old fields where new development could be considered as successful, all other producers brought in during the year being drilled in nearly exhausted pools to be operated as ('strippers." Northern Fields A total of 71 wells were drilled in the northern fields, of which 22 were producers; one well in Ebano was estimated at 5000 bbl. per day, while the general average of all producers was less than 300 bbl. Results

Jan 1, 1931

By D. R. Shoemaker

BACKGROUND AND PROJECT DESCRIPTION A 16.5 kt per day underground molybdenum mine is being developed at Questa in northern New Mexico by Molycorp, Inc., a wholly-owned subsidiary of Union Oil Company of California. Small scale underground mining first began in 1920 and large scale open-pit mining was initiated in 1965, but because of the high stripping ratio, surface mining is being phased out. Construction of the underground mine began in 1979, and first production is scheduled for 1983. Full production of 9 Gg of molybdenum per year will be reached in 1984. Access to the mine will be through a service shaft, development shaft, and a conveyor decline. 'The service shaft, 7.3 m in diameter and 396 m deep, will be used for personnel, supplies, development muck, and fresh air intake. It will be equipped with a large, double-deck man and material cage. A double-drum hoist will be used for cage hoisting and will handle up to a 27-t load in balance with a counterweight. Development muck will be loaded into skips in balance and a single-drum auxiliary hoist will provide secondary access. The 396-m-deep, 4.3-m-diameter development shaft will be used for initial mine development, mine exhaust air, and a slick line pass for concrete entering the mine. The development shaft is located 400 m north of the service shaft. Run-of-mine ore will be transported from one of two 1.4-kt storage pockets by a 1.2-m-wide conveyor belt located in the 10°, 1980-m-long, 5.0-m-wide, and 4.6-m-high decline. The decline conveyor belt has a centerline length of 2229 m and a vertical rise of 363 m. It will be powered by four 448 kw motors driving a single drive pulley. There will be two 1.2 m transfer belts on the surface with centerline lengths of 322 m and 542 m. All three conveyor belts will be reinforced with steel cables. On the surface, in addition to the headframes and hoist houses for the two vertical shafts, a large maintenance shop, warehouse, compressor house, change house, main office building and timber framing building have been constructed.

Jan 1, 1981