Search Documents

By H. W. Dow

Quite early in the beginning of the present century, hoisting equipment underwent a radical change, when electric motors were applied to furnish the power in place of steam engines. Naturally, in the beginning, motors were not employed for large hoists: most of them were small single-drum hoists for which the motor ran continuously and the drum was clutched in for hoisting by various methods, and the down-going trips were made on the brake. In 1911 the Nordberg Manufacturing Co. of Milwaukee built for the first time a double-drum hoist powered with a first-motion direct-current motor (Fig. I). This hoist embodied many of the features that are used on larger hoists today. In the early development of motor-driven hoists a more or less natural mis- take was generally made, which only recently is being corrected. Because the electric motor has a higher speed than the steam engine, mining people in general accepted, without question, the use of small-diameter drums and the resultant finding of the rope in multiple layers, which was not at that time, the general practice on first-motion steam hoists. Small-diameter drums can usually be driven by a motor through a single reduction of gears even with relatively high motor speed, therefore the complete equipment could be obtained with a lower first cost.

Jan 1, 1946

By D. Walton, W. C. Winegard, W. A. Tiller, J. W. Rutter

It is shown that the cellular substructure observed in binary alloy crystals grown from a melt of known concentration can be eliminated by the proper choice of growth conditions. For a given solute concentration, there exists a critical ratio of temperature gradient G in the melt to the rate of solidification R of the crystal, i.e., of G/R, which must be exceeded before the cellular structure can be eliminated. A secondary substructure is observed which is related to the cellular substructure. IN crystals grown from the melt, a prismatic substructure has been observed by Buerger,1 Pond and Kessler,2 and Rutter and Chalmers." This structure is columnar in the direction of growth and appears as a network of hexagonal cells in the plane of the solid-liquid interface. Rutter and Chalmers3 have shown that this substructure occurs as a result of the presence of a layer of high impurity concentration in the melt adjacent to the solid-liquid interface. The formation of the substructure is accompanied by a redistribution of this impurity in the neighborhood of the interface. The structure can be controlled by proper adjustment of the variables in the solidification process such as a rate of solidification and the temperature gradient in the liquid. The redistribution of solute during the solidification of metal crystals has been treated theoretically

Jan 1, 1956

By T. A. Rickard

In " The Genesis of Certain Auriferous Lodes "* Dr. Don makes a reference to a curious vein-formation known as the "Indicator," which characterizes a portion of the Ballarat mining district,, in Victoria, Australia. During 1890 and again in 1898 I had an opportunity of making a few notes, which, although somewhat belated,t may be worth adding to the observations recorded in the Transactions of the Institute. The country of the Ballarat gold-field consists of the Lower Silurian slates and sandstones, which also enclose the reefs of Bendigo; but it is noteworthy that the successive anticlinal folds, and accompanying saddles of quartz, which distinguish Bendigo are not characteristic of Ballarat, the geological structure of which presents greater complexity. That part of the district known as Ballarat East became famous early in its history on account of the large nuggets which were found in the alluvium, and subsequently it became further known because of a peculiar persistent black seam, traversing the bed-rock underlying the alluvial deposits, which was found to be associated with rich bunches of gold-ore, not only in the gravel that capped it at the surface but also in the quartz-veins which crossed it underground. The name of " Indicator " was early given. In 1871 Mr. Morgan Llewellyn directed attention to it as influencing the distribution of the gold. In the government quarterly report for December, 1888,

Jan 1, 1901

By R. W. Raymond

In a paper on the Divining-Rod (Transactions, xi., 411), presented at the Boston meting, in February, 1883,I suggested, among other signs of which the skilled prospector might consciously or unconsciously avail himself in the search for springs of water or mineral deposits, the presence of particular grasses or shrubs, and the general appearance of the flora. There are not wanting, in the literature of our art, indications that greater attention was paid to such signs in ancient days than at present. It is the tendency of a scientific age to ignore, or regard as superstitious, what cannot be classified or explained. But the acute though unscientific observation of earlier times often, doubtless, accumulated facts which it would be worth our while to re-examine. It is highly probable that the mining prospectors of the sixteenth and seventeenth centuries, to go no further back, were close students of nature, and knew, though they could not explain, and, for reasons of private gain, would not communicate, many curious and significant facts. We can generalize better than they could; but for that very reason we are, perhaps, their inferiors in observation. They let nothing pass, because all things were equally significant to them. We take wider views, and miss more. And, no doubt, there still exists among practical millers, prospectors,, hunters, Indians, etc., an unwritten.

Jan 1, 1887

By AIME AIME

THE iron and steel activities of this meeting opened on Monday morning with the steel melting session," with G. B. Waterhouse in the chair and A. L. Feild as vice-chairman. N. A. Zeigler's paper, on "Gases Extracted From Iron Carbon Alloys by Vacuum Melbing," created considerable interest and the discussion in general was most favorable. H. W. Gillett and Louis Jordan of the Bureau questioned the method of analysis for oxygen and C. H. Herty, Jr., and J. M. Gaines, Jr., I , expressed their surprise at the large amount of oxygen with the high ,carbon alloys. Whether the gases found existed as gas in blowholes or as oxide inclusions was also a moot point. A paper by C. D. King, on "Basic Open-Hearth Yields," was an extremely interesting and valuable contribution. It was discussed by C. E.Kinney and A. L. Feild and numerous questions were asked throughout the presentation. Mr. King then presented a critical analysis of the losses together with novel methods of calculating them. A paper by C. H. Herty, Jr., and J. M. Gaines, Jr., on "Unreduced Oxides in Pig Iron and Their Elimination in the Basic Open-Hearth Furnace," followed. The question of silicates and oxides in pig iron created much discussion, notably by Henry Hanson and W. J. MacKenzie, who gave figures on chipping cost as a function of blast-furnace practice.

Jan 1, 1929

By W. D. BRENNAN

AS a rule the thoughts of engineers are more often directed toward the mechanical and physical conditions of mining practice than they are toward the disposition and the marketing of the product. This, I think, has been true of the coal industry to the present time not only among the engineering force but also generally true of operators. There has been a tendency to place the sales department in a rather secondary position; for a great many years there was a greater demand for coal than the supply would meet, so it was only necessary to increase production: either by expansion of operating mines, or opening new mines of greater capacity. While the production of coal is still a highly important phase of the industry, its enormous development throughout the country, the great advance in fuel, efficiency and economy, and the discovery of new reserves of competitive fuels have combined to create a buyers' market and force the present-day attention upon merchandising in modern ways. A buyers' market has a natural tendency to develop the keenest competition, frequently unscrupulous and nearly always profit-wrecking. Under such conditions bad practices are bound to grow and to extend until the industry is wrecked, or until wiser heads get together to reduce or eliminate unfair methods of competition. This is not so recent a condition as one might believe.

Jan 1, 1931

By N. E. Norman

During the past few years the underground mining industry and the big hole drilling industry have been involved in a flirtatious courtship, but until recently this courtship did not appear to be taken too seriously by either party. However, many of the promises made by the big hole industry are beginning to come true. Improvements have been made steadily in techniques of mechanical boring of large diameter shafts, raises and tunnels, thus making the big hole industry a more stable partner in the eyes of the mining industry. The mining industry too has made many changes in planning that make mining more attractive to the big hole industry. If there is to be a marriage between big hole drilling and mining, we should certainly take a look at the background of the big hole drilling industry, and examine the three main features of big hole drilling to determine how each applies to mining. Shaft Drilling Since 1950, numerous large diameter shafts have been drilled using rotary drilling techniques. Most of the larger diameter shafts have been drilled for the AEC for underground nuclear testing purposes. However, since 1960 several shafts have also been drilled for various mining companies, particularly in the United States. In 1967, rotary drilling shafts were either completed or in progress at the mining companies listed in Table I.

Jan 6, 1968

By H. R. Ogden, E. S. Bartlett, A. G. Imgram

THE tensile and notch tensile ductile-to-brittle transition characteristics of several refractory metals and alloys have been well documented.1-3 Electron-beam melted tantalum and columbium have been shown to retain excellent ductility at very low temperatures. Some indications of brittle behavior (low ductility and cleavage fracture) were observed with columbium tested at -253oC, but no similar effects were noticed with tantalum. Increasing the interstitial oxygen content in these two materials resulted in the detection of indications of brittle behavior at higher temperatures, although good ductility was retained in both bases at -196°C when they contained about 1 at. pet 0. Detailed descriptions of the impact transition behavior of these two materials at various purity levels have not been available. This technical note describes the effect of interstitial oxygen on the impact properties of wrought, fibered tantalum and columbium and compares the transition behavior to the previously determined tensile transition characteristics. Tantalum and columbium impact specimens with three different interstitial oxygen levels indicated in Table I were tested at temperatures ranging from -196o to 300°C. Oxygen additions were made to 1/2-in.-diam bars of electron-beam melted material in a Seiverts Apparatus. The oxygenated bars were then homogenization-annealed to obtain uniform cross-section hardnesses and swaged to

Jan 1, 1964

By J. J. Egan

ADVANCES in the production of quality steel have emphasized the need for greater knowledge of the amount and distribution of oxygen in the steel. Control of inclusion content and quality is largely dependent on such knowledge. While many analytical methods have been de-vised for the accomplishment of this end, few are without serious limita-tions in accuracy, convenience, or skill required in application. Usually at least two methods are necessary to determine total oxygen and constituent oxides. Because of the great importance of this problem and the specific interest in the application of such methods of analysis, the various procedures were carefully reviewed at the Union Carbide and Carbon Research Laboratories, with the view of developing a method free from the limitations mentioned above. Intensive experimentation finally led to an improved iodine extraction analysis described by Cunningham and Price. I After this had been thoroughly checked from the standpoint of the analytical chemist, it was rechecked from that of the metallurgist. This involved preparation of a number of small heats of varying composition with determination of total oxygen in the molten metal by the alumina method2 and an analysis of the solidified material without the aluminum addition by means of iodine extraction; the oxides of iron, manganese, silicon and aluminum also being determined by the iodine analysis. The report of this work constitutes the subject of this paper.

Jan 1, 1933

By Mark Eisner

ONE'S JOB is the watershed down which the rest of one's life tends to flow write the Lynds in the first pages of their classic social study, "Middletown in Transition." Certainly engineers will confirm this statement after a check among those in their own profession with whose lives they are at all familiar. I have no hesitancy in acknowledging the truth of their observation for the men and women who are engaged in the profession of the law. It has been often remarked that American public life is overrun with members of the law profession. The highest public office in the land, that of President. has been occupied by lawyers almost to the exclusion of citizens of any of the other professions. Twenty-two Presidents of the United States out of the total of 31, were members of the bar. For the most part, members of Congress, the governors of the states, the state legislators and the mayors and other local leaders, men who occupy important positions of responsibility and public trust, have had legal training. Now this fact is no mere accident. Those who were fitted for the "job" of the practice of the law are favorably placed with respect to their participation in public life. Thus public service and public office is the watershed down which the "lawyer's" life tends to flow.

Jan 1, 1940

By AIME AIME

OUT of the fabulous iron ranges of Michigan?s Upper Peninsula since Pearl Harbor have come go to the steel mills to become tanks, guns, ships, and other weapons for a United Nations' victory. But the contributions to the war effort, as far as Michigan's iron country is concerned, do not stop there. The same men who mine iron ore deep inside the earth also are "mining" on top of the ground, gleaning a harvest of scrap iron and steel that is writing a big chapter in the War Production Board's salvage program. At virtually every mine over an area of a hundred square miles, everyone from the top mine official and straw boss to the man in the dippings is scrap conscious. They know the importance of the ore they mine but they are equally familiar with the importance of iron and steel scrap in war production. The successful job they are doing in salvage is a tribute to the entire Upper Michigan mining industry and to the man who marshaled them into action-John M. Bush, chief of the land department for the Cleveland- Cliffs Iron Co. at Negaunee, and for ten years an A.I.M.E. member. Also, this job should be an inspiration to 611 mining. metallurgical, and petroleum communities as to the latent possibilities of organized scrap recovery.

Jan 1, 1943

By John W. Trammell, Chester O. Ensign

Efficient mining of copper ore at the White Pine mine in Michigan's Upper Peninsula is partially dependent on the rather unique problem of predicting variations and rock types in a barren stratum called the upper sandstone. The pronounced effect which this formation has on the local mining techniques is reflected by the necessity of deciding whether to mine the sandstone along with ore-bearing rock, thus diluting overall ore grade, or, alternatively, leaving the sandstone behind to form the mine roof. THE OREBODY AND MINING TYPES In the mine, the cupriferous zone of the Nonesuch shale is divided into three major portions (Fig. I). Lying conformably on top of the Copper Harbor formation (or "lower sandstone") is the lower part of the orebody, the parting shale. The parting shale is overlain by the upper sandstone. On top of the upper sandstone, the basal portion (8 ft) of the upper shale is quite similar to the parting shale. Both the upper shale and parting shale are divided into a number of smaller stratigraphic units, each having a characteristic copper content, as shown by the histogram of Fig. 1. Other authors have dealt in detail with the stratigraphy and mineralogy of the orebody, so it will suffice here to call attention to the low copper content of the upper sandstone.

Jan 12, 1964

By C. R. Van Hise

[Concluding Contribution of Prof. Van Hise to the Discussion of his Paper, and Others on the Same General Subject, presented at the Washington Meeting, February, 1900 (see Ram., xxx., 27, 177, 323, 424, 578) ; also of the contributions of Vogt, De Launay, Beck, Lindgren, Kemp, Rickard, Bain, Keyes, Collins and Adams, presented at the Richmond Meeting, February, 1901, and to be printed in the present volume.] In June, 1900, shortly after my paper was published in the Fransactions, I made a briefer statement* before the Western Society of Engineers covering the same ground, which, in certain respects, is somewhat of an improvement. For instance, instead of using the terms descending and ascending &th reference to the waters resulting in the two concentrations, my modified statement is as follows: " The first concentration of many ore-deposits is the work of a relatively deep water-circulation, while the reconcentration is the result of reactions upon an earlier concentration through the agency of a relatively shallow water-circulation. Commonly the deep water-circulation is lacking in free oxygen, and contains reducing agents, and the shallow water contains free oxygen. The deep water is therefore a reducing, and the shallow water an oxidizing agent."† Of the papers upon ore-deposits which, in vol. xxx. of the Fransactions, follow my own, or which were presented at the Richmond meeting, a considerable number are wholly con-

Jan 1, 1902

By Milton C. Head, Aulton E. Roland, William E. Hawes

INTRODUCTION Uranium mining in the Grants Mineral Belt has undergone changes from methods pioneered during the 1950's and has now become fairly standardized throughout the district. The orebodies vary in size and shape and have been most successfully mined by using modified room and pillar methods with pillar recovery. This paper will expand on methods and equipment that are being used and modifications of these that will increase productivity and efficiency. GEOLOGICAL BACKGROUND The petrology of the Grants Mineral Belt consists of alternating layers of sandstone and shales (mudstone), with occasional thin layers of coal. The sandstones are aquifers which are generally artesian to some extent. The shales are bentonitic and decompose into extremely sloppy mud when exposed to water. Figure 1 shows a typical geologic section. Most of the uranium produced in the Grants Mineral Belt comes from the Westwater Canyon member of the Morrison Formation and occurs as scattered ore bodies throughout the formation. This formation consists of layers of bentonitic shale and sandstone of varying degrees' of cementing and grain size. It is also a very significant artesian aquifer. The unconfined compressive strength of the various formations is not high, as shown in Table I. It is important to note that these represent average values and a great range may exist within a single formation, especially In the Westwater which is the ore formation. [ ]

Jan 1, 1982

By Philip D. Pearson

Competition is the problem and modernization is the solution in today's underground iron operations on the Lake Superior Range. Profound changes in the iron ore picture during recent years have prompted correspondingly great changes in the economic position of the Lake Superior underground mines. To meet the ever growing competition from other lower cost iron sources, underground operators are becoming increasingly aware that the newest advancements in mining technology must be incorporated in their operations. UNDERGROUND POSITION TODAY The extraction of iron ore by underground methods has been going on for many decades in the Lake Superior region, starting in 1872 on the Menominee Range. The number of mines has changed gradually over the years as new ones were opened and old ones were exhausted, but in recent years, the most drastic change occurred from 1960 to 1961. In 1960, there were 31 underground mines operating in Michigan, Minnesota and Wisconsin, but at one period in 1961 only 20 were operating (Table I). In western Ontario so far there has been only some temporary curtailment of operations. Of the 11 U.S. mines which ceased operations in 1961, some may he closed only temporarily, but some will remain closed for our lifetime, at 'east, unless there is a tremendous reversal of the present trend in the iron ore market

Jan 3, 1962

The Institute conducts jointly with the American Society of Civil Engineers, American Society of Mechanical Engineers and American Institute of Electrical Engineers, certain activities as listed below, and is joint owner with them of certain properties. United Engineering Trustees, Inc. When Mr. Carnegie made his gift which made possible a home for the engineering societies, a separate corporation was organized to act as a holding company and to manage the common property. This was long known as the United Engineering Society but the name has now been changed to one which more nearly reflects the real function of the corporation. It holds title to the Engineering Societies Building and to various funds placed in its charge and is managed by a Board of Trustees of which three are chosen by each of the four societies, American Institute of Mining and Metallurgical Engineers, American Society of Mechanical Engineers, American Institute of Electrical Engineers and American Society of Civil Engineers, which own equal and undivided interests in the property. The land and building cost two million dollars. The interest of each of the Founders societies, aside from especial trust funds, is now valued at $493,352. The A. I. M. E. trustees are Arthur S. Dwight, J. V. N. Derr and George D. Barron. The President of the Board is Francis Lee Stuart and the Secretary, Alfred D. Flinn.

Jan 1, 1923

By C. S. Herzig

Some time ago, in Mexico, our signal-bells in a 700-foot shaft caused us considerable annoyance by continually getting out of order, each time so delaying our hoisting operations that we naturally desired to remedy this evil. There were two mays open: either to patch up the old bell, which was of the ordinary pattern, every time it failed to work, or else to devise some new arrangement.. On consultation with our foreman we designed a signal-device which, during the number of months I watched its operation, worked satisfactorily, without once getting out of order. We sought to produce a simple device, in which no greater pull on the lever would be necessary from one level than from another; to counterbalance independently the weight of the pendant bell-rope, so that there would be no direct weight on the working-parts of the bell itself, and likewise to arrange it so as to necessitate only a light pull on the lever in signaling; and, finally, to make some sort of trip-arrangement, so that whenever the signaling-lever underground passed through a certain arc the signal would be given in the engine-room. By this means we wished to obviate the ill effects of sudden heavy pulls and rough usage in general, such as all signaling

Jan 1, 1901

The Institute conducts jointly with the American Society of Civil Engineers, American Society of Mechanical Engineers and American Institute of Electrical Engineers, certain activities as listed below, and is joint owner with them of certain properties. United Engineering Trustees, Inc. When Mr. Carnegie made his gift which made possible a home for the engineering societies, a separate corporation was organized to act as a holding company and to manage the common property. This was long known as the United Engineering Society, but the name has now been changed to one which more nearly reflects the real function of the corporation. It holds title to the Engineering Societies Building and to various funds placed in its charge and is managed by a Board of Trustees, of which three are chosen by each of the four societies, American Institute of Mining and Metallurgical Engineers, American Society of Mechanical Engineers, American Institute of Electrical Engineers and American Society of Civil Engineers, which have equal and undivided interests in the property. The land and building cost two million dollars. The interest of the Founders societies, aside from especial trust funds, is now valued at $1,987,793. The A. I. M. E. trustees are William H. Bassett, H. G. Moulton and R. M. Roosevelt. The President of the Board is Harold V. Coes and the Secretary, Alfred D. Flinn.

Jan 1, 1934

By John Hays Hammond

This is an era of "expansion;" and, conformably with the change in commercial conditions, the function of the mining engineer, as well as that of his confréres in many other professions, has also expanded. From the position of an engineer, limited to the determination of technical questions, the engineer of to-day has come to assume an economic importance in those branches of industry dependent upon engineering skill for their development. He is indeed an engineer of limited usefulness who does not go further professionally than to submit a purely technical report on subjects presented for his consideration. While he has the same responsibility as formerly in the solution of the technical problems involved, he is further expected to supplement his report with advice on the financial and commercial aspects of these problems. For the great majority of problems presented to the engineer ultimately involve the determination of the pecuniary relations of the propositions under consideration. The great corporation lawyer no longer earns his fee by merely submitting his opinion as to the legal issues involved in law-suits affecting the corporation; he now assumes charge of the entire legal work, including both the organization of the corporation and the maintenance of its legal status thereafter. In like manner, the engineer, whose report was, as I

Jan 1, 1909

By James Marsh

INTRODUCTION Economists have long expressed suspicion of the economic theory of natural resource exhaustion, even in writing articles which have contributed to it (1). Indeed, the gap which separates the pure theory from practical management seems unusually wide. It is doubtful whether a mine manager could possibly know enough about the relevant parameters of his mine to steer it along the optimal paths described by the theorists (2). Nevertheless, enough faith in the theory remains that mine managers are suspected of being a separate breed whose behavior must be studied in special courses using specialized text-books, collections of readings, and journals (3). The implied hypothesis, that mines and natural resource firms are managed differently than other firms, is the subject of this paper. In the next section the theory is developed and analyzed. In section III, I discuss the implications of the statistical results that have been obtained. Finally, conclusions are reserved for section IV. THE MODEL A key difference between the traditional theory of natural resource production and that of other forms lies in the set of variables which ire assumed to jointly determine the quantity of output the firm will produce. Output, in the non-resource case, is assumed to be a function of k clearly definable and distinguishable inputs or factors of production, viz., y = f(xl, x2, ..., xk), (1) here

Jan 1, 1977