Search Documents

By Lillian Erskine

While brass and other copper alloys have long been listed as offering health hazards to their workers, it is questionable if the metals involved are alone responsible for the trades' records of morbidity. The entire science of foundry sanitation is the product of the past two decades; and the best standards now operative would have been regarded as little short of revolutionary prior to 1910. The special handicap to the conservation of the health of the brass founder's employees has been the fact that, unlike the iron founder, his business could be profitably carried on in almost any small and unsanitary quarters. As a result, writers on occupational disease have accepted brass chills or brass founders' ague as an inevitable feature of the trade; and respiratory disabilities, as well as phthisis and disturbances of the nervous system, are also included as prevalent among those employed. While there can be no question as to the basic accuracy of past investigations, there is every reason to doubt the necessity for an undue percentage of ill health among brass molders and casters who are safeguarded by scientific ventilating standards and by improving personal habits of sobriety. There is, however, need for a campaign of education as to the most approved practices and equipment whereby the employer may safeguard the health of his workers, and thereby reduce his labor turnover and increase his productive efficiency. Broadly speaking, copper, tin, and aluminum carry negligible health hazards. The toxic qualities of lead, however, are a menace; especially if scrap lead is recovered or bought for foundry processes. The rapid volatilization of zinc renders its fumes and flocculent condensation the chief problems in conserving the health of the brass worker. The frequent presence in the foundry air of traces of arsenic compounds, lead

Jan 1, 1919

By J. L. Christie, R. H. Leach

SO much has been written recently about the use of silver to replace scarce metals that certain facts about silver and its uses should be of interest. Figures for the production and use of silver, taken from the Handy & Harman annual reviews of the silver market, are given in Table 1. It will be seen that the rate of production has remained fairly constant and has been affected in recent years by the production of base metals, of which silver is a by-product. In each of the years 1937, 1938, and 1939, the U.S. Government acquisitions alone exceeded the entire world production, the difference, of course, being made up by imports of previously accumulated stocks. In 1940 and 1941 the U. S. Government acquisitions plus the United States and Canadian uses in the arts and industries exceeded the Western Hemisphere production. The U.S. Government pays a premium price for silver newly mined in the United States, at present 71.11c. compared with the price of 35'/8c. for foreign silver, with the result that the current U. S. production is not used commercially for the arts and industries. At the time this is written (June 1942) there is much uncertainty as to the future effect of this situation.

Jan 1, 1942

By A. H. Rhoades, D. T. King, R. J. Gray

Tests and methods of detecting oxidized coal are studied. Particular emphasis is placed on the microscopically discernible changes that accompany the chemical and physical changes affecting the technological properties of coal during oxidation. Coal samples were used from the low-volatile Pocahontas No. 3 Seam, McDowell County, W.V., and from the high-volatile Cedar Grove Seam, Mingo County, W.V. Tests conducted include: carbonization, free-swelling index, phase inversion, froth flotation, Gieseler plasticity, oxygen by difference and by neutron activation, volatile matter, pH of coal slurries, alkali solubility, and electrostatic charge.

Jan 1, 1977

By Bernard MacDonald

Introduction. OF the treatment of the slime-pulp of gold- and silver-ores by cyanidation, agitation is an essential part. When prepared for treatment, this pulp, consisting of ore reduced to such fineness that approximately 80 per cent. of it will pass through a 200-mesh screen, is mixed with a certain proportion of water, carrying in solution the quantity of cyanide (KCN) and other chemicals required. The water-constituent of the pulp thus prepared usually ranges from 1 to 2 parts by weight to 1 of the dry ore. Thus constituted', the pulp is charged into treatment-tanks, the shape and capacity of which vary, according to the quantity of pulp to be treated daily and the method of agitation to be employed. Tanks have no other function in a cyanide-plant than that of being economical and convenient containers or receptacles for holding the pulp, solution, or water used in the operations. It is by agitation that the solids in the pulp charged into the tanks are kept in suspension in, and mixed with, the solution in the proper proportions required for the treatment. If the proper mixture of solution to solids be determined to be 2 to 1 by weight (which is, approximately, 5 to 1 by volume), this proportion should be maintained in every part of the charge ; -that is, each solid particle of the pulp, whether it be of 180- or 400-mesh size, should, be surrounded by five times its own volume of solution throughout the whole period of treatment. The reason is, that the amount of chemicals ascertained to be necessary for dissolving the gold and silver contained in the solids, is held in uniform solution in the water-constituent of the pulp, and, therefore, the determined proportions of solution and solids must be maintained at all times during treat-

Apr 1, 1912

By F. M. Lewis, J. F. Myers

W. I. Garms-—The authors state that when they added 11 tons of balls to the 45 pct volume ball load, the power needle did not budge. The question arises as to whether any increase in capacity accompanied the 11-ton addition. It is hardly conceivable that all of the balls making up the 11-ton addition were sterile. However, as the work done in the ball mill is not by kilo-watthours per se or balls per se but by kilowatthour-balls, it is possible that the kilowatthourballs in the mill before the 11-ton addition had a different amperage, voltage or robustage than those in the mill after the addition and that the overall outcome was that equal work was done before and after the addition. The authors can keep the efficiency that they got with the 45 pct volume 1-in. ball charge and get additional capacity by putting more kilowatthourballs to work in the form of the addition of 11 tons of 2-in. balls to the present ball charge, and subsequent makeup additions by weight of 20 pct 2-in. balls and 80 pct 1-in. balls. J. F. Myers (authors' reply)-—Mr. Garms points his finger at the 11 tons of "sterile" balls added to the Tri-cone mill. A fact so interesting to us that we felt it should be reported. Clearly, ball slippage at the existing mill speed prevented any further transfer of power from the shell to the ball mass. We agree that the kilowatthourballs would increase, were we charging rough 2-in. balls as suggested by Mr. Garms. The assumption is, of course, that we would get a corresponding increase in work done. Our reported data (CIME meeting, Vancouver, 1946) shows a gain of work accomplished of 7.6 pct as we decreased the ball size from 2 in. to 11/2 in. and a further gain of work accomplished of 2.1 pct when we went from 11/2 in. to 1 in. The small ball results reported by H. R. Banks at Chapman Camp are also very convincing. In the case of 2-in. balls they would take the conventional ball path and start cascading. They would thus destroy the classifying pool over the "foot" of the

Jan 1, 1951

By J. F. Myers, F. M. Lewis

W. I. Garms-—The authors state that when they added 11 tons of balls to the 45 pct volume ball load, the power needle did not budge. The question arises as to whether any increase in capacity accompanied the 11-ton addition. It is hardly conceivable that all of the balls making up the 11-ton addition were sterile. However, as the work done in the ball mill is not by kilo-watthours per se or balls per se but by kilowatthour-balls, it is possible that the kilowatthourballs in the mill before the 11-ton addition had a different amperage, voltage or robustage than those in the mill after the addition and that the overall outcome was that equal work was done before and after the addition. The authors can keep the efficiency that they got with the 45 pct volume 1-in. ball charge and get additional capacity by putting more kilowatthourballs to work in the form of the addition of 11 tons of 2-in. balls to the present ball charge, and subsequent makeup additions by weight of 20 pct 2-in. balls and 80 pct 1-in. balls. J. F. Myers (authors' reply)-—Mr. Garms points his finger at the 11 tons of "sterile" balls added to the Tri-cone mill. A fact so interesting to us that we felt it should be reported. Clearly, ball slippage at the existing mill speed prevented any further transfer of power from the shell to the ball mass. We agree that the kilowatthourballs would increase, were we charging rough 2-in. balls as suggested by Mr. Garms. The assumption is, of course, that we would get a corresponding increase in work done. Our reported data (CIME meeting, Vancouver, 1946) shows a gain of work accomplished of 7.6 pct as we decreased the ball size from 2 in. to 11/2 in. and a further gain of work accomplished of 2.1 pct when we went from 11/2 in. to 1 in. The small ball results reported by H. R. Banks at Chapman Camp are also very convincing. In the case of 2-in. balls they would take the conventional ball path and start cascading. They would thus destroy the classifying pool over the "foot" of the

Jan 1, 1951

By M. G. Nicholas

The influence of deformation, relative movement and surface cleanliness on the strength of room -temperature "interparticle" bonds between copper surfaces has been studied. No bonding resulted when clean surfaces were merely pressed together, even under pressures of 50,000 psi. Bonding resulted, however, when clean surfaces were simultaneously pressed and moved relative to each other, some bonding occurring no matter how small the pressure or relative movement. Exposure of the clean surfaces to various chemicals inhibited bonding, none at all being produced by small relative movements. The size of the movements which first produce bonding between exposed surfaces depends on the nature of the chemical, being less than 0.002 in. for cleansing reagents and greater than 0.004 in. for lubricants, water and hydrogen sulfide. It is concluded from the experimental data that the prime requirement for bonding is the dispersal of surface films such as oxides and adsorbed contaminants. THE formation of interparticle bonds during the room-temperature compaction of powder metallurgy components greatly increases the ease of handling in subsequent production operations prior to sintering. The strength of unsintered compacts follows the same general trends as their density and hardness, but quantitative data are extremely Scarce. Quantitative correlation of the data on the overall strength of a compact with that of the individual interparticle bonds is virtually impossible due to the extremely complex geometry of powder compacts. Qualitatively, however, the strengths of unsintered compacts can be correlated with variations in parameters known to influence the extent of cold bonding, and hence interparticle bonding, such as surface cleanliness, relative movement, and deformation of the mating surfaces. Kuzmic and seelig4 found that contamination of powder particle surfaces with lubricants reduced the strength of unsintered iron and copper compacts. Interparticle shear has been shown to promote bonding by Train and Hersey7 while Gregory has shown that die rotation is beneficial. Eilender and schwalbe6 concluded that most bonding occurred during the early stages of pressing iron powder compacts when interparticle shear is one of the principal processes occurring. mile there can be little doubt that these and other factors, such as particle size and shape, affect the extent of interparticle bonding produced by compaction, evaluation of the influence of individual factors is not easy. Particle deformation and relative movement, for example, occur simultaneously during compaction, making any precise measurement of their relative influences difficult. Because of these and other difficulties encountered in studying interparticle bonding in actual powder compacts, the approach adopted in this study was to

Jan 1, 1963

By H. B. Treweek, V. R. Degner

Current mineral industry trends toward handling the high tonnages of lower grade ore and tailings retreat lead to a continuing need for large volume flotation cells. The benefits which accompany the larger cell flotation circuit include reduced capital cost, less mill floor space, reduced operational complexity, and less maintenance, provided the metallurgical performance and solids suspension capability of the cell are not compromised. This study reviews development considerations pertinent to large mechanical air induction type flotation cells from the standpoint of cell internal hydrodynamic characteristics and metallurgical performance. While the importance of process related factors such as chemical usage, pH control, solids size and loading, and circuit arrangement cannot be denied, this study will emphasize the relationship of cell size (volume), mechanism geometry (impeller diameter), and mechanism operating conditions (rotor speed and submergence), to air transfer, liquid circulation, liquid "rise velocity" and mechanism power draw. Specific hydraulic performance maps for large capacity 300 and 500 cu ft flotation cells will be reviewed in terms of the relationship between the operational variables and the air and liquid flow conditions within the cell. Metallurgical results, obtained under plant operating conditions for 300 and 500 cu ft cells, are included to illustrate the metallurgical performance similarity of flotation cells which follow hydrodynamic scale-up criteria set forth in this investigation.

Jan 1, 1976

By C. M. Brinckerhoff

Safety work in mining at the Andes Copper Mining Company, Potrerillos, Chile, is divided into three parts: (1) accident prevention, (2) fire prevention and protection, and (3) silicosis prevention and control. In the company's operations a steady campaign has been waged to reduce accidents and silicosis, and to prevent fires. In the following pages the safety record for the past twelve years will be examined and the methods explained by which the accident rate was reduced. Table 1 contains yearly data pertaining to the scale of the mining operations and the accident record. Block caving is used for all ore production and the tonnage mined has averaged 30,000 short tons per day for the past seven years. Table 2 classifies 44 fatal accidents which have occurred since 1935. The leading causes of accidental death are transportation of ore and use of explosives, followed in order by persons falling, falls of ground, and by asphyxiation. In the case of serious accidents, however, the greatest cause is falls of ground, followed, in turn, by ore transportation, persons falling, explosives, and asphyxiation. Accident Prevention The improvement of the safety record was obtained by a combination of many factors. In surveying the results at Andes for the past twelve years, it is possible to select some features of the present operation which have contributed to the accident record. The most important of these are: (1) good staff planning, (2) good equipment, (3) an alert safety organization, and (4) education and selection of the workmen. GOOD STAFF PLANNING As a result of good staff planning, the mine has good working conditions, namely, good ventilation, moderate temperatures and humidity, and good lighting. These factors not only reduce accidents but also improve efficiency. In haulage work, accidents have been reduced by having traffic move in a forward direction only. The latter makes possible a one-man train crew. Trains are centrally dispatched from loading drifts which are interconnected by signal lights, so that when a train in a lateral drift is given permission to move into a main line drift, a red light signals in all other lateral drifts in that area. Good track is maintained, and safety niches are required at all switch throws. Since safety niches were provided there have been no fatal or serious accidents at such points. All main line haulage drifts are illuminated by electric lights. Haulage drifts are kept clean. Adequate clearance has been provided between cars and between cars and the sides of the haulage drifts. The 4 1/2 ton Cranby type cars are equipped with roller bearings, and the 10 ton loconlotives with trolley shoes instead of wheels. These two features are responsible for improved ore haulage conditions and contribute to greater efficiency and safety.

Jan 1, 1950

By CHARLES HOPPER

In preparing the Steep Rock Lake iron ore body for mining, it was necessary to drain Steep Rock Lake. Using diamond drills, a cut 1800 ft long, 100 ft wide, and maximum depth of 95 ft amounting to 300,000 cu yd of material, was excavated in Greenstone to provide a drainage channel. This was done under the general contractor C. A. Pitts, of Toronto, who in turn employed a diamond drill contractor, Boyles Bros., to do the drilling. The method of excavation was selected be- cause a clean square cut and grade could be maintained in the bottom of the channel. Bootlegged holes would have left blocks of rock in the corners which would have created a situation which would have become progressively worse as the open cut advanced from one side of the ridge to the other.

Jan 1, 1949

By W. D. Lowry

As most of the industrial activity of Oregon is centered in the Portland area, the foundries there consume the bulk of the foundry sand produced in Oregon. Although a number of the larger towns scattered throughout the state have gray-iron foundries, the sand used by most of them is of local origin. The yearly consumption of foundry sand of all types for the past few war years in Oregon is estimated to have been approximately 40,000 tons valued at about $285,000, of which an estimated 18,000 tons was shipped in from the Ottawa, Ill., district for use largely by the steel foundries. Until 1945 much of the silica sand consumed by the steel foundries in the Pacific Northwest, approximately 50,000 tons in 1944, came from Ottawa, Ill. and surrounding regions. Although some silica sand was shipped in from Belgium in the past, none is known to have been imported in recent years. Early in 1945, a very promising high-grade silica sand being produced near Eugene, Oregon, was introduced, and all but two of the Portland steel foundries are using this new sand. Until a few years ago, the search for good local (Oregon) foundry sands was carried on largely by the foundry supply houses. Recently the Oregon Department of Geology and Mineral Industries has investigated a number of deposits and has carried on and fostered research on the most bromising deposit near Eugene, about 120 miles south of Portland. High-grade silica foundry sand from this deposit is now being marketed in Oregon, Washington, and British Columbia. The Eugene sand is one of the very few outstanding western steel-foundry sands. Field investigations by the Oregon Department show that there are relatively few deposits of sand in Oregon suitable for foundry use. A knowledge of the geology of the state makes this readily understandable. The only major primary sources of the quartz present in sandstones in Oregon are the intrusive masses of granite, granodiorite, and quartz diorite of late Jurassic or early Cretaceous age found in the Siskiyou Mountains of southwestern Oregon, a part of the old Klamath Mountain highland, and in the Blue Mountains of northeastern Oregon. Transportation militates against the development of any possible deposits of foundry sand found east of the Cascade Mountains in central and eastern Oregon because few railroads traverse that area. East of the Cascades, which separate western from eastern Oregon, many of the older sediments of Paleozoic and Mesozoic age have either been metamorphosed or contain much volcanic eruptive material, and even if some of the Mesozoic sediments are highly quartzose in places, they are in relatively inaccessible areas. All the Tertiary sediments there are of continental origin and contain much ash and other volcanic debris, for there was great volcanic activity during much of that period. In western Oregon much the same is true of the Paleozoic and Mesozoic rocks

Jan 1, 1948

By W. D. Lowry

As most of the industrial activity of Oregon is centered in the Portland area, the foundries there consume the bulk of the foundry sand produced in Oregon. Although a number of the larger towns scattered throughout the state have gray-iron foundries, the sand used by most of them is of local origin. The yearly consumption of foundry sand of all types for the past few war years in Oregon is estimated to have been approximately 40,000 tons valued at about $285,000, of which an estimated 18,000 tons was shipped in from the Ottawa, Ill., district for use largely by the steel foundries. Until 1945 much of the silica sand consumed by the steel foundries in the Pacific Northwest, approximately 50,000 tons in 1944, came from Ottawa, Ill. and surrounding regions. Although some silica sand was shipped in from Belgium in the past, none is known to have been imported in recent years. Early in 1945, a very promising high-grade silica sand being produced near Eugene, Oregon, was introduced, and all but two of the Portland steel foundries are using this new sand. Until a few years ago, the search for good local (Oregon) foundry sands was carried on largely by the foundry supply houses. Recently the Oregon Department of Geology and Mineral Industries has investigated a number of deposits and has carried on and fostered research on the most bromising deposit near Eugene, about 120 miles south of Portland. High-grade silica foundry sand from this deposit is now being marketed in Oregon, Washington, and British Columbia. The Eugene sand is one of the very few outstanding western steel-foundry sands. Field investigations by the Oregon Department show that there are relatively few deposits of sand in Oregon suitable for foundry use. A knowledge of the geology of the state makes this readily understandable. The only major primary sources of the quartz present in sandstones in Oregon are the intrusive masses of granite, granodiorite, and quartz diorite of late Jurassic or early Cretaceous age found in the Siskiyou Mountains of southwestern Oregon, a part of the old Klamath Mountain highland, and in the Blue Mountains of northeastern Oregon. Transportation militates against the development of any possible deposits of foundry sand found east of the Cascade Mountains in central and eastern Oregon because few railroads traverse that area. East of the Cascades, which separate western from eastern Oregon, many of the older sediments of Paleozoic and Mesozoic age have either been metamorphosed or contain much volcanic eruptive material, and even if some of the Mesozoic sediments are highly quartzose in places, they are in relatively inaccessible areas. All the Tertiary sediments there are of continental origin and contain much ash and other volcanic debris, for there was great volcanic activity during much of that period. In western Oregon much the same is true of the Paleozoic and Mesozoic rocks

Jan 1, 1948

By C. S. Matthews, H. M. Girner, C. D. Williams, M. J. Edwardson, H. R. Parkison

Quantitative interpretation of electric logs requires knowledge of formation temperature. In this paper, methods are developed for computing changes in formation temperature caused by circulation of mud during drilling operations. The basis of the method is the mathematical solution of the differential equation of heat conduction. The solution of this equation is presented in a series of graphs. These graphs are used to determine formation temperature disturbance at various radii for arbitrary mud circulation histories. Example comparisons with field results show reasonable agreement. It is concluded that, in general, the temperature disturbances caused by circulating mud are small beyond 10 ft from the wellbore but are quite significant near the wellbore. INTRODUCTION Quantitative interpretation of electric logs requires knowledge of the formation temperature in order to establish the resistivity of the formation water with accuracy. To determine the formation temperature, the temperature disturbances produced by circulating drilling mud must be evaluated. -The objective of this investigation was to develop a method for the numerical determination of these temperature disturbances at any distance from the wellbore as a function of time. The first step was to solve the differential equation describing the temperature behavior in the formation during and after mud circulation. This solution was used to calculate a series of curves relating temperature disturbance to shut-in time for various circulating periods. An "exact" method for computing formation temperatures with the use of these temperature-disturbance plots is described, and the results of an application of this method to a well in Montana are presented. Procedures for approximating formation temperatures are also discussed. BASIC EQUATIONS AND ASSUMPTIONS With the assumptions that (1) cylindrical symmetry exists, with the borehole as the axis, (2) heat flow is 1. The formation can be treated as though it is radially infinite and homogeneous in extent, as regards heat flow. 2. The presence of mud cake can be disregarded. 3. The effect of heat generated by bit action is negligible. 4. After mud circulation ceases, the rate of radial heat flow at the wellbore is negligible and is assumed zero for purposes of calculating temperature change with time. These assumptions are believed to be reasonable because of the agreement achieved between calculated and measured borehole temperature in a well, to be discussed later. Further, the agreement at the wellbore indicates that temperatures in the formation were also approximately correct. since it is the formation temperatures that determine wellbore temperature after ceasing circulations SOLUTION OF THE DIFFERENTIAL EQUATION AND ITS APPLICATION The solution of Eq. 2 for the temperature behavior during and after a single period of mud circulation is

By Oliver C., Ralston

THE following data were obtained during Tan exhaustive research into the possibilities of concentrating United Verde massive sulfide copper-zinc-iron ores by flotation. The composition of these ores approximates the following mineralogical analysis: 3 to 15 per cent chalcopyrite; 3 to 11 per cent marmatite (ferruginous sphalerite) ; 47 to 69 per cent pyrite; and 10 per cent quartz. The remainder is usually schist gangue. The sulfide minerals are finely dis-seminated; chalcopvrite and marmatite begin to be liberated on grinding at about 100 mesh, but complete liberation from gangue (pyrite in this case is considered a gangue mineral) is

Jan 1, 1935

By Leo Ranney

ANY years ago a prospector came to a Nevada town and built himself a shack. Day after day he searched the hills for gold -but he found none. He closed his shack and hurried north, where a strike had been made. Next he tried to trap the flour gold that floats down the Snake River. He panned the black sands along the Oregon coast. He ranged over the mountains and up the gulches of far-off Alaska. At last, broken in health, six years ago he came back to his old home in Nevada. There his shack still stood-nobody wanted it. One day he started a garden in the rocky soil that he owned. His spade turned up a chunk of quartz, and in that quartz were stringers of gold. He had found a rich gold vein, running right under his own house. You gas producers who have hurried to Oklahoma, Louisiana, East Texas, South Texas, West Texas, even to California to drill wildcat holes a mile or two miles deep-why not, like the old gold prospector, have a look in your own back yard? Some of your coal seams contain 20,000,000 cu. ft. of natural gas per acre.

Jan 1, 1943

By J. B. Cohen, O. F. Kimball

Aging of specimens of Au-20 at. pct Ni and Au-40 at. pct Ni has been followed with electron microscopy, resistance, magnetic measurements, and X-ray diffraction. The periodic structures observed by electron microscopy in Au-Ni alloys by Fisher and Embury are shown to be due to nickel-rich prepre-cipitates. Assuming this alloy system undergoes spinodal decomposition, our observations and available data on thermodynamic properties and elastic constants indicate that the gradient energy coefficient in this system is of the order of 10-5 ergs cm-1 . Shifts of X-ray peaks in this system have been found to be due primarily to residual stresses, not faulting. A large effect of applied stress during aging was detected by X-rays and electron microscopy for the Au-20 at. pct Ni alloy. The presence of a preprecipitation stage during aging of gold-rich Au-Ni alloys for short times below 300°C has been indicated by several previous investigations. Changes in electrical resistivity,1"3 elastic modulus,4 superparamagnetisrn,5 positions of X-ray diffraction peaks,6 and hardness7 have been studied. Electron diffraction and microscopic studies by Fukano8 and Fisher and Embury9 respectively showed that the precipitation process resulted in the formation of periodic composition fluctuations—perhaps spinodal decomposition. MOSS10 detected a satellite with X-rays in quenched specimens, but the wavelength was much smallerthan that found by Fukano. Recently Woodilla and Averbac11 detected a modulation similar to that found by Moss, but with electron diffraction. They suggested that the microstructures observed by Fisher and Embury may be simply due to a Moir'e effect from a back deposit of gold during electropolishing. Satellites in electron diffraction can be enhanced by small bends or tilts of a foil. Even if this were not the case, asymmetric satellites, as are found in Au-Ni are difficult to analyze. They are principally influenced by the large differences in atomic size in this system, and obtaining information on the associated composition fluctuations depends on assumptions as to whether or not there are isolated clusters or composition "waves", and in the latter case whether or not the entire specimen has decomposed. Assuming that decomposition was complete in alloys aged at low temperatures, Woodilla and Averbach suggested that the satellites indicated a composition which varied about the average value by only± 5 pct, much less than that predicted from the phase limits, Fig. 1; they attributed this small variation to a cessation of the reaction caused by the loss of mobile vacancies. In Ref. 12 it was shown that vacancies are trapped by the preprecipitate in this system. Furthermore, after reversion, aging proceeds at a much slower rate than immediately after a quench from the solution temperature,5'11,13 indicating the importance of vacancies in the kinetics. In some senses Au-Ni is a favorable system for studying preprecipitation and reversion mechanisms because of the simplicity of the equilibrium diagram14 and the availability of good thermodynamic15 and diffusion data.16,l7 The calculations necessary to relate the decomposition process to classical nucleation and growth or to spinodal decomposition, as well as those necessary for understanding reversion mechanisms, can, therefore, be made. As an example, the position of the chemical spinodal, calculated from the thermo-dynamic data of Sellars and Maak15 with the method described by Rundman and Hilliard,18 is included in Fig. 1. It is compared to the chemical spinodal calculated from the equilibrium miscibility gap by Cook and Hilliard's method.l9 Included is the coherent spinodal suggested by Golding and MOSS," using measured elastic constants for their calculations and the same ther-modynamic data. The spinodal estimated by Woodilla and Averbach,11 by determining the temperature limits for the observation of the satellites discussed above, is also given. Actually this last curve is open to question on the following grounds: As a phase boundary is approached the spacing of particles or the wavelength

Jan 1, 1970

By J. C. Yannopoulos, N. J. Themelis

Ah electronic thermogravirnetric balance was used to measure the veductioiz rule o single cirpric oxide particles suspended in a stream of hydrogen. Very jzne thermocouples embedded in lie center and at the surface of the sphere recorded the variation of terw perature during reduction. In contrast to iron oxide reduction, where in most instances the rate of interface reactiokl is controlling, the heat- and mass-transfer phenotnena play a predolrinant role in the reduction of cupric oxide. The correlation of experitnental data or tnass lransfev lhrough the boundary layer at Reynolds nunlber 0-4 50 was as jollocs: ThE reduction of cupric oxide by hydrogen is represented by the equation: It is a highly exothermic reaction and the amount of heat released varies only slightly with temperature (-21,430 cal per g-mole at 400°C). Most of the published studies on this system have been conducted at temperatures in the range of 34 to 280c.l-&apos; The concensus of opinion has been that at temperatures below 200°C the reaction is preceded by an induction period during which there is very little or no reduction. The length of this period diminishes as the temperature of the reaction is increased1l5 and aseawa found that at 280°C reduction starts practically immediately when the oxide is exposed to hydrogen gas. The existence of an induction, or incubation, period has led experimenters to believe that the reduction of CuO by hydrogen is catalyzed by metallic copper.&apos; Boldurev and rmolaev found that mechanical additions of powdered copper to oxide did not affect its reduction, although metallic copper produced during the reduction seemed to have a catalytic effect. At least three other authors2&apos;5&apos;7 have reported that addition of copper had no effect on the rate of reduction. Pease and alor&apos; observed that water vapor had a strong inhibiting effect on the reduction at 1503C, but its effect was greatly diminished at 200 C. Pavlychenko and Rubinchik5 studied this reaction at 159 to 235 C and found that, once the reaction had been initiated, there was no inhibiting effect due to the introduction of water in the hydrogen stream; at temperatures above 183°C there was no inhibiting effect due to water vapor, either before or during reaction. The same authors noted that the rate of reduction was independent of pressure in the range of 200 to 700 mm Hg. aseawa investigated the kinetics of the CuO-Hz system at 160 to 280°C and estimated the apparent activation energy at 14,000 cal per g-mole. A similar value (13,500 1200 cal per g-mole) was reported by ond&apos; in the temperature range 148 to 216°C. Bond also reported that there was no incubation period and that water vapor had no inhibiting effect on reduction at temperatures above 190 C. The above studies have been conducted at temperatures below 280°C and the physical configuration of the system under investigation has not been defined adequately. However, it is well-known that the mechanism of gas-solid reactions depends on a number of in series physical and chemical rate prcesses.&apos;&apos; It is, therefore, essential to include among the experimental factors the geometry of the solid system and the mass-transport characteristics of the reducing gas. Scott studied the reduction of packed beds of cupric oxide cylinders by Hz-He streams of very low hydrogen concentrations at temperatures 400 to 600 C, pressure of 10 to 30 atm, and gas velocity from 0.18 to 5.8 ft per sec (3 < Rep < 30). The reduction rate was found to be mainly controlled by diffusion through the boundary layer and through the pores of the reduced copper phase. The following correlation was proposed: Scott in an earlier work studied the reduction of fixed beds of cupric oxide wire and found that the rate of flow of the gas stream through the bed had a controlling effect on the rate of reduction. The same mass-transfer phenomenon was observed by Bond and clark13 on a similar reduction system. The analogy between mass and heat transfer through the boundary layer which exists between a solid surface and the bulk stream stems from the similarity of the differential equations representing these phenomena

Jan 1, 1967

By Nicholas J. Grant, A. W. Mullendore, Paul Predecki

The Duwez technique of splat cooling in which a molten droplet of metal is accelerated and made to impact on a cold, highly conducting substrate was investigated.- An apparatus for producing "splat" was constructed employing an explosive powder charge to accelerate the molten metal. Transport of the molten metal just prior to impact with the substrate was studied by means of high-speed photography. The molten particles are small spherical droplets from about 1 to 50 µ diameter. The average cooling rates for aluminum, silver, and a gold alloy splatted on nickel substrates at room temperature were determined experimentally and were found to vary from 18 to 5 x 10&apos; C per sec. The heat-transfer coeficients for pure aluminum and pure silver splats cooled on nickel substrates at room temperature were found to be 2.7 to 6.8 and 13.6 to 54.2 cal per sec sq cm &apos;C (2 to 5 x 104 and 1 to 4 x 18 Btu per hr sq ft OF), respectively. Solidification rates in pure aluminum and silver splats were calculated. "SPLAT cooling" is a term describing a technique for extremely rapid freezing and cooling of molten metals and alloys to room temperature or below. The technique was developed by Duwez et al.&apos; in 1960, and after refinement2 consisted in transferring a few tenths of a gram of molten metal to near sonic velocity to strike a suitably placed cold copper surface. Upon impact, the metal spread into a thin nonuniform film called a splat, about 10-4 cm thick. The splat particles produced in this manner were thin enough in some areas to be suitable for transmission electron microscopy, without further treatment, and, together with X-ray data, yielded a variety of structures which would be classified as follows: 1) supersaturated solid solutions (increase in solubility limit), 2) metastable crystalline stoichiometric and non-stoichiometric intermediate phases ( in Au-20.5 at. pct Si and in Au-14 at. pct Sb, respectively), 3) amorphous alloys, 4) retained high-temperature phases, 5) alloys having equilibrium phases present, but with unusual, markedly altered structures. The crystalline phases present in splats were usually extremely fine-grained and had low dislocation densities. Present interest in splat cooling centers around a study of the unusual structures produced by the technique, their contribution to alloy theory, and the possibility of the development of new or unusual properties. In addition, the technique is being examined for the production of bulk quantities of new high-strength alloys for low- and high-temperature use. Although a number of alloy systems have already been investigated by the technique, relatively little is known about the mechanism of splat formation and the physical conditions encountered by the metal during solidification and cooling. The purpose of this work was: 1) to determine the velocity, shape, and size of the molten metal droplets just prior to impact with the cold substrate; 2) to try to estimate or measure solidification rates, heat-transfer coefficients, and cooling rates in splats. EXPERIMENTAL TECHNIQUE Splatting Apparatus and Procedure. An apparatus similar to the type originated by Duwez et a1.,2 but employing an explosive charge to accelerate the molten metal, was used. A "Ramset" fastening tool (a gun normally used for driving studs into concrete, steel, and so forth) was mounted vertically above a resistance-heated graphite crucible as shown schematically in Fig. 1. A splat product was produced by melting a few tenths of a gram of metal at the position shown in Fig. 1, and then exploding a powder charge in the breach. The shock wave thus generated traveled down the barrel into the furnace, ejecting the molten metal through the 0.06-in.-diameter hole at the bottom of the crucible. The ejected metal was impacted on a high-conductivity metallic substrate where it formed a splat. High-Speed silhouette Photography. In order to investigate the size and shape of the ejected, molten metal just prior to impact with the cold substrate, high-speed silhouette photographs were taken, and are shown in Figs. 2 and 3. These photographs were obtained with the aid of an Edger-ton, Germeshausen, and Grier microflash unit and a submicrosecond flash drive equipped with a variable time delay. Two types of triggers were

Jan 1, 1965

By Edward Keller

Jan 1, 1906

By A. S. Malicsi, I. Iwasaki

Differential flotation of bulk sulfide concentrates from Duluth gabbro into copper and nickel concentrates could be implemented by first destroying the hydrophobic coating with ozone and then by recovering the copper concentrate with a copper-selective collector. A number of parameters involved in the use of ozone, such as the sequence and the conditioning time of ozone treatment, the pulp pH, and the level of xanthate addition, were investigated.

Jan 1, 1986