Search Documents

By T. Egleston

FOR a great part of the progress of the world we are indebted to the works of engineers. It is to them that we owe our means of rapid transportation, our canals, our railroads, our bridges, many of our automatic machines, and most of those appliances which, by facili tating or decreasing the amount of human labor to be expended and by utilizing the great forces of nature, have made the present progress of the world possible. Their education is a matter of momentous interest to the whole civilized world. I have, therefore, thought that some discussion of the theory upon which their education should be based would be of interest to this body, and have ventured a few reflections and suggestions upon the subject. The word education, in its original signification, meant the draw ing out of a man what there was in him. In our common schools the practical work of education consists in putting into the brain a larger number of facts than can be retained, which are consequently more or less understood and digested. It ordinarily consists simply of teaching a round of abstractions or facts which when not assim ilated are not only useless to the individual, but generate careless habits of thought and make more or less untruthful, unfaithful or unsuccessful men. In most of our schools a procrustean system is adopted; all are made to advance upon one general plan, the quick being kept back and the slow dragged on at a rate too great for their power of comprehension. Until within a very few years it has been a theory in common school education that the brain alone should be developed, and that little or no attention need be paid to the train-

Jan 1, 1888

By K. Mukai, M. Ishihara

This report is a brief discussion of the impurity levels both in primary aluminum and super-purily alnminim in connection with raw materials and proc-essing methods. Particularly, truce amounls of im-purities were analyzed by introducing nittss-speclro-gruphy and nenlron-aclivalian analysis techniques. Vanadium and gallium content in primary aluminum metal corresponded to theor amounls in anode coke. but the nickel content in primary aluminum was hide-pendent oj its amount in the anode cake. Sulfur in the anode colic might result in an increase of the iron content in the molten metal in the reduction cell. The content of sodium and calcium increased with increasing bath ratio. In the holding furnacc sodium content decreased rapidly, and nonmetallic inclusions merit separated front the mollen metal. Three-layer elctrolysis was effectire in eliminating many impuri-ties with the exception of copper, aluminum oxide. aluminum nitride, and some rare-earth elements. THE amount of impurities and nonmetallic inclusions in aluminum metal depends on impurities in the raw materials and various production processes. This paper presents an investigation of the behavior of impurities and nonmetallic inclusions in aluminum during the electrolysis process, the period in the holding furnace, and the process of three-layer electrolysis. Chemical analysis and emission spectrometric analysis have generally been used as methods to determine small amounts of impurities in both primary aluminum and super-purity aluminum; however. mass spectrography and neutron-activation analysis have been recently introduced into this field, and trace amounts of impurities can accurately be determined by these latter methods. EXPERIMENTAL WORK Common impurities were determined by means of absorptiometric. polarographic, flame-photometric. and emission-spectrometric methods. However, in the determination of trace amounts of impurities and non-metallic inclusions, the following methods were applied. In the analyses of trace impurities by mass-spec- trographic analysis, samples were exposed in the vacuum spark of double-focus ing Mattauch-Herzog type mass spectrograph (Japan Electron Optics Laboratory, Ltd.). Ilford Q2 photographic plates were used as ion detectors. Fe was used as the internal standard, and the atomic concentration of each element was calculated by the following expression and converted into the weight concentration: where E, and Ei are the exposures (coulomb) when isotopes of the internal standard and impurity elements (on which the estimate is based) show the same density, X is the percent (atomic) concentration of the standard, IF and Ii are the percent abundances of the isotopes of the standard the impurity elements (on which the estimate is based), and Ms and hfi are the mass of the isotopes of the standard and impurity elements (on which the estimate is based). The coefficient of variation in this method is about 40 pct in the range of 0.1 to 1 ppm. In neutron-activation analysis, irradiations were done in the nuclear reactors TRIGA-I1 (neutron flux: 4.7 x 10 11 n per sq cm per sec; Rikkyo University) or JRR-2 (neutron flux: 2 x 1013 n per sq cm per sec: Japan Atomic Energy Research Institute). After the chemical separation, a NaI (3 by 3 in.) scintillator connected to a 256-channel y-ray spectrometer (R.C.L.) was used for counting and recording various activated impurities. The coefficient of variation in this method is about 20 pct. In the analyses of nonmetallic inclusions, aluminum-oxide determination was carried out according to Fischer's method, 3 as follows. A slice of sample was cut off and the surface was cleaned. It was dissolved in bromine-methanol. The solution was filtered and the residue was washed. The residue was fused with potassium bisulfate flux. Then it was dissolved in weak acid, and oxine solution was added. The aluminum oxinate was extracted with benzene. Finally, aluminum was determined absorptio-metrically. Aluminum nitride determination was carried out as follows. A slice of sample was cut off and the surface was cleaned. It was put in the distillation apparatus and decomposed with sodium hydroxide solution. The solution was distilled. Then ammonia was absorbed and

Jan 1, 1967

By A. M. E. Eilers

No one who has visited our Western mining districts, and studied the economical part of the beneficiation of the ores occurring all over that vast extent of country, can underrate the high importance of the above subject. By far the larger number of the districts which contain smelting ores, i.e., argentiferous and auriferous lead, or copper ores, are situated in the Great Basin, that great plateau between the Rocky Mountains on the east, and the Sierra Nevada on the west, almost the whole of which is comprised at present in the boundaries of Nevada, Utah, and part of Arizona. This region is essentially a barren country. The extreme dryness of the atmosphere permits but a scanty vegetation in the plains ; and even in the detached mountain-chains running through it-generally from N. to S., or from N. W. to S. E.-there are no trees found except dwarfed pines and mahogany, at the head of sheltered ravines, and a few cottonwoods and willows, which fringe the insignificant streams, before the water sinks in the arid plains. Nearly all the mountain-chains in this region are rich in silver ores. That class of these ores which is adapted to amalgamation, and rich in silver, has been worked with profit for more than ten years. But before the advent of the transcontinental railways, mining was restricted to these ores alone, and the consumption of fuel could be met with the scanty supply of forest trees in the immediate vicinity of the mining districts. Since, however, the Union and Central Pacific Railroads have brought the Great Basin nearer to the commercial centres of the East and the Pacific coast, thus reducing the expenses of freight and labor materially, other silver deposits, containing poorer ores in greater abundance, have been rapidly taken

Jan 1, 1873

By A. Satter

Studies of wellbore heat transtnission during the injection of a hot fluid, as either gas or liquid, have appeared in he literature. The present investigation takes into account the effect of condensation, which is of practical sig-nificance when considering steam injection operations. Calculation procedures are given for superheated and for saturated and undersaturated steam. Effects of injection rate, time, pressure, temperature and depth of a well on heat losses have been analyzed. The benefits of using a packer are discussed. Also presented are correlations for estimating heat losses involved during injection of saturated steam. INTRODUCTION Studies of wellbore heat losses during the injection of a hot fluid have appeared in the literature. Ramey' has presented a useful solution for calculating temperature of a heated gas as a function of depth and injection time. Ramey and others have also presented solutions for the hot liquid case.'. ' No method is available to take into account the effect of condensation, which is of practical significance when considering steam injection operations. This paper presents a method of estimating the quality of a condensing fluid as a function of depth and time. The approach is basically the same as that used by Ramey. The following injected fluids and conditions are considered in this study: 1. Injection of superheated steam A. Decrease in temperature until cooled to the saturated state B. Condensation until condensed completely into hot (saturated) water 2. Injection of saturated or undersaturated steam; condensation until condensed completely into hot (saturated) water. Although this investigation does not include cooling of water after steam is completely condensed, Ramey's solution for the hot liquid case can be used for this purpose. The effects of various process variables on heat losses During the injection of steam into a well are investigated. THEORY QUALITY OF CONDENSING STEAM Predicting the behavior of condensing steam flowing down the injection wellbore requires an estimate of the quality of steam, i.e., the mass fraction of vapor in the mixture. Let us divide the total depth of the injection well into several segments which might be, but do not have to be, of equal magnitude. Consider condensation within a given depth interval AZ, the bottom of which is located at a depth Z from the surface (Fig 1). The following equation, derived in the Appendix- relates the quality of steam at the bottom of an interval to that at the top of the interval:

Jan 1, 1966

By C. B. Alcock, M. G. Hocking

The kinetics of the growth of sulfate layers on blocks of Cu20 has been studied between 688" and 800°C. At 788c the over-all weight increases followed the parabolic rate law, with k = 216 30 sq mg per cm4 min, using a 1:1 entering gas mixture of SO2:02. At 757 after an initial linear period the parabolic rate law was followed, with k = 57.8 10 sq mg per cm4 min. The gas mixture required a platinum catalyst to produce the maximum SOs pressure. The sulfation rate at 757' and 788c was high until all the CUZO had changed into a core of CuO, when it became very much lower. At 757°C marker experiments showed that the sulfates (CuO. CuS04 and CuSO4) grow outwards from the oxide surface, but CuO. CuS04 mixed with CuO was found beneath the markers. At 688 markers were found at the CuO. CuS04/CuS04 interface. Visual observations at 757 showed a liquid eutectic moving beneath the sulfate surface. causing very rapid sulfation and extruding to solidify as thick 'needles" up to 8 mm long. Marker experiments have shown conclusi.cely that CuO grows on Cu20 in air by the outward migration of copper. ThermODYNAMIC measurements on the sulfate and basic sulfate of copper, reported recently,' are followed here by measurements of the rates of formation of these sulfates on cuprous oxide, in order to provide a background for the understanding of roasting processes. peretti2 and McCabe and Morgan3 have shown that the phase Cu20 lies next to Cu2S when the sulfide is roasted under conditions where sulfates will be formed. Since this would present too complex a system for kinetic study, the present work4 has been based on the kinetics of sulfation of the oxide phase. The results of a study of the kinetics and mechanism of the sulfation of cobaltous oxide have recently been reported.4,5 Results on the sulfation of cuprous oxide have also appeared,6 but are at variance with those to be reported here. This seems to be because the previous workers6 did not obtain constant SO3 pressures from the SO2/O2 sulfating gas mixtures used, as will be discussed later. Wadsworth, Leiter, Porter, and Lewis found that the sulfates produced when SO2/O2 mixtures are passed over Cu20 at red heats are CuS04 and the basic sulfate CuO.CuSO4. When the decomposition of CuS04 was followed' by differential thermal analysis, a stage corresponding to CuO .CuS04 was reached before decomposition into the oxide occurred. APPARATUS The vertical furnace used for quantitative studies was a conventional resistance-heated and propor- tionately controlled furnace with an even zone (1 deg) which was 4 cm long. The gas mixtures of SO2 and 02 were made by mixing measured flows from capillary flowmeters and drying over phosphorous pentoxide before passing them into the Pyrex top-piece of the furnace assembly. A mullite tube of bore 2% cm was used as reaction vessel and at the bottom of this tube was a trap for SO3, which condensed as a colorless liquid. The residual gas was led into a fume cupboard for ventilation to the atmosphere. The furnace used for visual observations of needle growth and other phenomena consisted of a transparent silica reaction tube of bore 3 cm, having an optically flat silica window sealed into its wall. The reaction tube was clamped vertically, inside a mullite tube of bore 4 cm and length 42 cm which was heated by Kanthal windings. The window in the silica reaction tube was arranged opposite a hole 3 cm wide and 2 cm tall which had been cut in the wall of the mullite winding tube 19 cm from its top end. A binocular microscope was used to look through the window, illumination being provided by a focusing microscope-lamp offset sideways and downwards. The oxide block to be sulfated was suspended from the removable Pyrex top-piece to the reaction tube, by means of which it was inserted at the start of the experiment, and through which entered the S02/02 gas mixture. The variation of the temperature inside the reaction tube with horizontal and vertical displacement from the window was investigated, and, while it can be said that the temperature was constant 1 deg, its value at a given position was known only to 12 deg. In both furnaces, the oxide block to be sulfated was suspended from a small silica hook immediately downstream from a platinum thimble used as catalyst, which was held on a long silica rod from a Pyrex spring attached to the removable Pyrex top-piece of the furnace. The spring was only included in the quantitative sulfating furnace; its sensitivity was 1.4 cm per g and it was found to be free from creep in a 16-hr test when carrying the working load. The extensions were followed by a cathetometer which could be read to 0.001 cm, corresponding to i0.7 mg. Extensions of the spring were measured on adding weights between 5 and 500 mg to the working load (thimble + oxide block), and Hooke's law was closely obeyed. SAMPLES Cuprous oxide blocks were prepared by oxidizing Johnson Matthey "Specpure" copper sheet of 1 mm thickness (impurities: iron at 3 ppm, silver at 2 ppm, lead, nickel, sodium, and silicon each at 1 ppm, calcium, chromium, magnesium, and manganese each at less than 1 ppm) for 6 days in air at 1000°C in a re-crystallized alumina boat. It has been reported7 that when Cu20 is prepared by heating copper sheet for 1 day the central plane of the blocks produced consists

Jan 1, 1967

By C. R. Knopp

Gas-oil relative permeability ratio is an important relationship in oil reservoir predictive calculations. A correlation has been developed from 107 gas-flood k/k tests on Venezuelan core samples. The correlating parameter is based on restored-state water saturation tests and' is applicable to both consolidated and poorly consolidated sandstone reservoirs. Data of the correlation show that there are no distinguishah1e differences between the mass-data groupings for the two c1assifications A procedure is recommended for running .sufficient relative. permeability analyses to compute a geometric mean of the sample group. The geometric mean is more representative of the total core, and probably the entire reservoir. For example, while only one in four of the k,,/k,., test curves agreed closely with the resultant correlation of this report, the geometric mean curves of the 16 suites (three samples or more). showed good agreetment ill three cases out of four. INTRODUCTION The gas-oil relative permeability ratio is an important, fundamental relationship in most oil reservoir predictive calculations. Predictive calculations are made to estimate future reservoir production characteristics and ultimate oil recovery. The k1,/k2, relationship is specifically needed to relate the surface gas-oil ratio to the reservoir oil and gas saturation, and to calculate the relative movement of these phases within the reservoir whenever some of the more complex driving mechanisms are present. Laboratory k1/k2, tests are not generally run as a routine analysis. Consequently, k1/k2 data often are not available when needed because the cost of laboratory work could not be justified or the need for such data had not been properly anticipated. When laboratory k1/k2, data are available, they are often very difficult to interpret. For example, wide divergence is sometimes shown in a family of k1,/k1, tests representative of the producing horizon in a single well. With these considerations in mind, a study was made to determine if a relationship might exist between the k1,/k2, curve and some other simple laboratory test criteria. The most probable k1/k2, curve correlation for Venezuela described in this paper is the result of the investigation. The presented correlation defines the most probable gas-flood k,,/k,, curve through the medium of air-water capillary displacement and centrifuge water saturation tests. The laboratory procedures of these tests are. relatively simple, and inexpensive; test data should be. widely available- from routine analysis. DATA AVAILABLE, LABORATORY METHODS The report correlation utilized 107 gas-Hood k1/k2, tests run on sandstone cores of Venezuelan reservoirs. Table 1 is a general tabulation of data pertinent to the tests, while Table 2 summarizes the data. Thetests include 96 from Western Venezuela and 11 from Eastern Venezuela. Eighty-two- of the 107 test samples were sandstones that varied from poorly consolidated to-unconsolidated; 25 were consolidated. The average sample porosity was 26.7 per cent and the average permeability was 1,121 md; these values typify the better sandstone reservoirs of' Venezuela. The Welge gas-flood technique,' based on fundamental Buckley-Leverett frontal displacement theory, was introduced in about 1952 and is widely accepted in the industry. The laboratory procedure is relatively simple, rapid, and can be performed on small core samples. While there have been some minor variations in sample preparation and laboratory procedure in the tests used for the correlation, these tests can be generally summarized as follows. The core sample was first sol vent-extracted and dried. Connate-water saturation was restored by the oil-flushing or evaporation-blow down methods. At the beginning of gas flood the hydrocarbon pore volume was completeiy saturated with the test oil phase. Unsteady-state gas-oil displacement then began with the injection of nitrogen or helium. while the displaced oil and gas phases were incrementally metered at the out-flow face. From the test data, the k,,/k,, curve was calculated by the Welge method.' The individual oil and gas relative permeabilities were also calculated." CORRELATING PROCEDURES In attempting to establish a basis of correlation, we found that broad mid-range sections of 105 of the 107 k,,/k,, test curves could be closely duplicated by a straight line. Only two curves did not show a degree of linearity in this region. Correlation-curve definition parameters were subsequently developed from this observation of consistent mid-range linearity. Possible correlating variables were limited to the physical properties measured on core samples that (1) were widely available as common test data and (2) could be easily and cheaply obtained through future laboratory work. The more obvious possibilities were porosity, permeability and

Jan 1, 1966

By A. G. McGregor

During the past 5 years, five new copper-smelting plants have been built and put into operation in the State of Arizona. The monthly copper output from these plants averages from 5,000,000 to 18,000,000 lb. Previously, there never was as much activity in copper-smelting plant construction in the same length of time in all the rest of the world. Naturally, in this amount of work, some new problems were met and new features in plant design and equipment developed. Some of these features are described in this paper. Concentrate Hauling, Unloading and Sampling System (a) Concentrate Car The International Smelting Co. has provided at its plant at Miami specially designed cars for hauling the concentrates from the mills of the Inspiration Copper Co. and the Miami Copper Co. The car has a bottom that is readily made tight to hold flotation concentrates and is quickly and cheaply unloaded. Figs. 1, 2 and 3 show views and details of the car. The main feature of this car is the slot in the bottom throughout its length, which is closed by means of short planks that overlap like ship-lap as shown by Fig. 1. At one end of the car an iron gate operated by a screw and hand wheel is provided, which clamps or presses the planks together, making the bottom tight. A removable tapered plug rests vertically over this gate when the loading of the concentrates at the mill commences. A concentrate unloading pocket (Fig. 4), 180 ft.long, is provided at the smelting plant, which has a conveyor belt running throughout its length underneath the track. To unload a car, the vertical plug at the end of the car is lifted by means of a chain hoist which is supported by a trolley overhead. The gate at the end of the car is opened approximately 18 in. The removal of the plug leaves a hole down through the concentrates. The concentrates are poked through the hole from the top of the car until it is convenient for a man to stand on the bottom and draw one of the slats in the bottom toward the gate end of the car. The concentrates are then raked down with hoes on their natural angle of repose,

Jan 1, 1917

By C. E. Brown, D. C. Helms, O. W. Shimer

The early history and progress of anthracite stripping, from the first known operation at Summit Hill in 1821 through 1917, was covered in 1917 in a paper by J. B. Warriner,1 then chief engineer, now president of the Lehigh Navigation Coal Co., and stripping methods between 1917 and 1931 were the subject of a paper in 1931 by H. H. Otto,2 of the Hudson Coal Company. . The present paper is confined to methods used today on pitching beds in the western middle and southern anthracite fields. The anthracite industry, not unlike other large industries, had been affected for more than a decade by the adverse economic conditions of the country. High development and operating costs and the competition of other fuels caused some collieries to be closed temporarily, while others were permanently abandoned. In order to obtain a larger tonnage at a lower development cost, a larger stripping program was put into effect by many companies. In 1932, stripping operations accounted for 3½ million tons, or 7 per cent of the total anthracite production of the year, and in the next 10 years this increased until more than double that amount, or over 14 per cent of the total production, was from stripping operations. These figures represent the total production of the entire anthracite region; unfortunately, the figures have not been separated from the different fields. There are some operations in the southern and middle western fields where the tonnage obtained from stripping amounts to more than 30 per cent of the total colliery production. Stripping operations on pitching beds present difficult problems. Owing to the various geological formations, a different situation is encountered in nearly every stripping pit; and because of the proximity of an overlying bed, it is very often necessary to load the entire overburden into trucks and haul it out of the pit to the dump area, although back filling and casting is done whenever possible. Beds in the areas described in this paper pitch from 20" to 90 and some are on the invert in many sharp folds and faults. Planning The more successful strippings have had adequate engineering analysis. Some work is being done without much preliminary planning, but many strippings would have failed completely if close supervision by the engineering department had not been . maintained. Locations of stripping areas are determined as follows: I. By constructing cross sections over the areas and drilling sufficient diamond-drill or well drill holes to study the strata and to determine the location, thickness

Jan 1, 1944

By J. B. Morrow, D. H. Davis

THERE are two general approaches to the problem of increasing profits from an operation. One is to lower expense; the other is to raise income. Mechanical preparation of coal may be used for either purpose but a prudent consideration of many details must precede any decision lest the results be negative instead of positive. It is quite possible that any net gain will result from a combination of the two. Since mechanically prepared coal invariably is a better product qualitatively than a hand-picked coal from the same mine, it is a reason- able expectation that the customer will be willing to increase the producer's income by paying a higher price. Or there may be the possibility that a combination of mechanical mining plus mechanical cleaning will give a lower over-all production cost for the coal in the railroad car. More likely, there will be found a combination of these two factors. From the customer's point of view, the competitive delivered cost per B.t.u. considered in relation to such incidental factors as dust nuisance, handling properties, ash disposal, and ash fusibility determines what he will pay. In a bulk tonnage product such as coal, freight is a very considerable part of the delivered fuel cost, and obviously freight paid on incombustible ash has no economic attractions. INCENTIVE FOR CLEANING Coal is prepared in four major ways: 1 (I) by screening or sizing, (a) by mixing or blending, (3) by cleaning, including hand picking and mechanical cleaning, (4) by dustless treatment. By a combination of any or all of these methods, coal can be prepared to standard specifications. It is easily possible to have good cleaning and still get a poor final product because of faulty screening or mixing,

Jan 1, 1943

By Charles Catlett

(Chattanooga Meeting, October, 1M.) THE terms " developed " and " undeveloped " are necessarily relative and cover a wide range; but the latter is here applied to cases in which the information at hand falls short of a clear demonstration of values, and conclusions must be reached from a study of the geological conditions of the particular deposit, interpreted in the light of similar and closely related deposits. Such an inquiry might be characterized as an effort to reach reliable conclusions from insufficient data. But the engineer engaged in commercial work finds himself often face to face with apparently such problems; and while he may realize with regret that a small amount of intelligent development would add enormously to the value of his conclusions, he is compelled to recognize the demand of a business situation for a prompt decision as the basis of immediate action. In a case within my knowledge, the question involved was the purchase of 50,000 acres of coal-land, and 10 days was the limit within which this question must be decided. Of course, it was impossible to make a satisfactory examination within that time; but the 'instructions were "to make the most complete examination and the most positive recommendation possible." Such instructions are often given; for, no matter how much time an investor may have, he is likely to put of his decision until the last moment, and then discover that he needs more light and advice. It does not follow that engineers, after full explanation and mutual understanding of the situation, should decline to undertake examinations thus limited. In the case just mentioned, while only the broadest view was possible, half the time available was sufficient to show that the property was a good purchase. The timber alone was subsequently resold for more than the entire purchase-price of the

Mar 1, 1909

By Herbert Clark Hoover, Lou Henry Hoover

SINCE the Sixth Book has described the iron tools, the vessels and the machines used in mink, this Book will describe the methods of assaying1 ores; because it is desirable to first test them in order that the material mined may be advantageously smelted, or that the dross may be purged away and the metal made pure. Although writers have mentioned such tests, yet none of them have set down the directions for performing them, wherefore it is no wonder that those who come later have written nothing on the subject. By tests of this kind miners can determine with certainty whether ores contain any metal in them or not ; or if it has already been indicated that the ore contains one or more metals, the tests show whether it is much or little ; the miners also ascertain by such tests the method by which the metal can be separated from that part of the ore devoid of it ; and further, by these tests, they determine that part in which there is much metal from that part in which there is little. Unless these tests have been carefully applied before the metals are melted out, the ore cannot be smelted without great loss to the owners, for the parts which do not easily melt in the fire carry the metals off with them or consume them. In the last case, they pass off with the fumes ; in the other case they are mixed with the slag and furnace accretions, and in such event the owners lose the labour which they have spent in preparing the furnaces and the crucibles, and further, it is necessary for them to incur fresh expenditure for fluxes and other things. Metals, when they have been melted out, are usually assayed in order that we may ascertain what pro- portion of silver is in a centumpondium of copper or lead, or what quantity of gold is in one libra of silver ; and, on the other hand, what proportion of copper or lead is contained in a centumpondium of silver, or what quantity of silver is contained in one libra of gold. And from this we can calculate whether it will be worth while to separate the precious metals from the base metals, or not. Further, a test of this kind shows whether coins are good or are debased ; and readily detects silver, if the coiners have mixed more than is lawful with the gold ; or copper, if the coiners have alloyed with the gold or silver more of it than is allowable. I will explain all these methods with the utmost care that I can.

Jan 1, 1950

By S. R. Seagle, R. Schuhmann, N. A. Parlee

Rates of CO evolution and CO absorption were measured for liquid-iron alloys containing from 0.15 to 4.4 pet C, using a modified Sieverts apparatus. The alloys were held in alumina crucibles, so that both crucible-metal and gas-metal reactions occurred simultaneously. The data are interpreted on the hypothesis that the C-O reaction rate is controlled by oxygen diffusion across the boundary layers at the gas-metal and crucible-metal surfaces. CARBON-monoxide evolution from liquid Fe-C-0 alloys is a key reaction in steelmaking processes, both in the steelmaking furnace and in the ingot mold. Also, this reaction probably is an essential step in the desulfurization of iron under blast-furnace conditions, for which carbon is the principal reducing agent or deoxidizer present in the iron. The thermodynamic properties of the solutions of C and 0 in Fe and the equilibria of these solutions with gaseous CO and CO, have been investigated in some detail and are reasonably well understood. However, while these equilibrium data have accumulated in the laboratory, other data have accumulated to show that equilibrium conditions are often not achieved under plant operating conditions. Thus, an understanding of the rate and mechanism of the carbon-oxygen reaction not only has theoretical interest, but ultimately may assume considerable practical importance. Reaction Mechanisms and Rate Equations The over-all reaction under consideration is C (in liquid Fe) + 0 (in liquid Fe) + CO (gas) [I] Although this appears to be a straightforward heterogeneous reaction, involving just two phases (liquid metal and gas), a wide variety of reaction mechanisms has been proposed. Different authors have expressed divergent views as to the nature of the rate-controlling steps. Accordingly, a brief discussion of the possible reaction steps will be given. 1) Homogeneous Reaction Within Liquid Iron— Feild' and Jette2 have applied chemical reaction-rate theory as if the C-0 reaction were a homogeneous, second-order reaction occurring within the liquid-metal phase. This mechanism necessarily produces CO "molecules" dissolved in liquid iron. In order to yield CO gas, the dissolved CO must nucleate CO gas bubbles, and the dissolved CO also must be transported to the bubble surface where it enters the gas phase. However, this mechanism is inconsistent with present concepts of the structure of liquid-metal solutions. 2) Reaction at Gas-Metal Interface—At the surface of contact between gas and metal, a second-order reaction between dissolved C and 0 may occur to produce a CO molecule which enters the gas phase. This reaction presumably involves an "activated complex" structure in the interface. Some such surface mechanism appears essential because the carbon and oxygen do not occur in the same species in the two phases and therefore must react in some way at the surface. At liquid-iron temperatures, calculations based on reaction-rate theory indicate that the surface reaction must proceed extremely rapidly and thus cannot be a rate-determining step in the C-O reaction under ordinary conditions.3 ccordingly when the over-all reaction is measurably slow, the surface reaction may be considered at equilibrium; that is Cc* Co* = m'Pco [2] in which Co* and Co* are the concentrations of carbon and oxygen (weight per unit volume of metal), respectively, in the liquid-metal phase at the interface, Poo* is partial pressure of CO in the gas phase at the surface (atmospheres), and m' is the mass-action constant for Reaction [I]. Since activities of C and 0 are not strictly proportional to concentrations, m' is not a true thermodynamic equilibrium constant but varies with carbon content.' 3) Mass Transport—If the reaction is to proceed at the gas-metal surface, as described above, dissolved carbon and oxygen in the liquid iron must come to the surface and gaseous carbon monoxide must move away from the surface. Details of the mass-transport mechanisms depend on the kind of system under consideration. For a stirred metal bath in contact with a CO gas phase, the transport of C and 0 to the surface can be described by 1 Do Mols CO evolved per sec = — 1/16— Do/do Agm (CO-Co*) = 1/12 Do/do Agm *(Co-Co*) [3] In this equation, Do and D, are the diffusion constants for oxygen and carbon in liquid iron, 6, and 6,. are the boundary-layer thicknesses, A,,,, is the

Jan 1, 1959

By G. Derge, W. Peifer, J. H. Richards

INTRODUCTION A WIDE variety of metallurgical defects in steel have commonly been attributed to the presence of excessive amounts of hydrogen. These defects include flakes in rails and forgings, cracks in welds, and blisters in enameled ware. They have been related to hydrogen largely by circumstantial evidence because the proper sampling and analysis of steel for hydrogen has been known to be difficult and because no general agreement has existed with regard to the relative suitability and accuracy of available methods. The need for a direct approach to these problems has been widely recognized. This general situation has been well described in the publications of the British Committee on the Heterogeneity of Steel Ingots,1 and current approaches to the problem were reviewed in a recent symposium of the AIME.12 The plans described by the present authors at that meeting have now matured satisfactorily and will form the basis of this paper. The principle object of this paper will be to describe the methods of sampling and analysis which have been developed and to illustrate the usefulness and limitations of these methods by citing their application to a specific problem. The first problem selected for investigation was the behavior of hydrogen in rail steel. This was chosen because the occurrence of shatter cracks in rails has received a great deal of study over a long period of time. The defect can be controlled by the expensive procedure of slow cooling. However, it may be hoped that a better understanding of the factors influencing the hydrogen content of rails will lead to a more efficient control of this problem. Rails provide a good starting point for a more general study of hydrogen in steel because they provide a cross section large enough to develop cracks, yet small enough for convenient handling and sampling. Rails were also selected because they are made from plain carbon steel and it was felt that the initial work should not be complicated by the effects introduced by alloying elements. The considerations which determined the original planning of this study should be reviewed. The inherently complex nature of most hydrogen problems requires that a large amount of data must be collected for any particular case. This in turn means that any analytical procedure should be as rapid and simple as possible. The same objective of speed is indicated by the fact that it may finally become desirable to use hydrogen analysis in process control. It is also known that hydrogen is highly fugitive and that any procedure which facilitates early analysis of the sample without prolonged or irregular storage has distinct advantages. The most important previously reported methods of analysis may be classified into three general groups: (I) Vacuum fusion. (2) Vacuum extraction (without melting). (3) Total combustion.

Jan 1, 1948

By H. H. Klepfer, K. J. Gill, P. Chiotti

SOME observations relative to the U-Zn system have been made by other investigators. Chipman1 and Carter2 have reported the preparation of several U-Zn alloys and point out that these alloys are generally difficult to prepare. Chipman1 reported evidence for a high melting compound at about 90 atomic pct Zn and the possible existence of a eutec-tic between the compound and uranium. Raynor," in a theoretical discussion of the alloying properties of uranium, included zinc among the elements predicted to have little or no solubility in a, p, or y uranium. In the present investigation, thermal analyses, X-ray, metallographic, and vapor-pressure data were obtained to determine the phase boundaries. The relatively high zinc pressure over most of the alloys at temperatures of 900 °C and above proved troublesome and special techniques had to be employed in preparing suitable alloys. Materials and Preparation of Alloys The metals employed in this investigation were Ames Laboratory biscuit uranium containing less than 500 ppm total impurities and Bunker Hill slab zinc or Baker Analyzed reagent granulated zinc, both with a purity of 99.99+ pct. Due to the high vapor pressure of zinc and the high reactivity of both uranium and zinc with oxygen at only moderately high temperatures, alloys were prepared in closed containers which had either been evacuated or evacuated and filled with helium. High purity magnesia, magnesia containing 10 pct calcium fluoride, and tantalum proved to be suitable crucible materials. Tw-o different procedures, described below, were used to prepare alloys, the latter being the most satisfactory. The metals, uranium turnings and granulated zinc, were cleaned with dilute nitric acid, rinsed, dried, and placed immediately in a helium-fill'ed dry box. The two metals were placed' in a 10 mil Ta crucible. The charge was enclosed in the tantalum crucible by welding on a preformed tantalum cap. This assembly was enclosed inside a stainless steel (AISI 309) bomb. The bomb was made by welding a piece of stainless steel plate on each end of a stainless steel pipe. All these operations were carried out in a helium atmosphere. These assemblies were heated in a muffle furnace at temperatures between 1100" and 1200°C for 10 to 15 min or held as long as 15 to 20 hr in the 950" to 1000°C temperature range before quenching. Spectrographic and chemical analyses showed no tantalum pickup by the alloys, indicating no reaction between the alloys and the crucibles. However, some of these crucibles failed, probably due to imperfections in the welds of the stainless steel or tantalum crucibles. The second and most satisfactory method was to prepare the alloys by powder metallurgy techniques. The procedure was to press degreased and acid-etched uranium turnings with granulated zinc into 20 g compacts under 20,000-psi pressure. The compacts were placed in MgO crucibles, and sealed in evacuated Vycor or fused silica tubes. The alloys were then heated as long as two weeks at about 550°C in a muffle furnace. The pressed compacts were observed to expand by several volume percent during heating and it was necessary to make allowances for this expansion in order to avoid breaking the crucible and Vycor tube. This method was found very satisfactory for preparing alloys which were suitable for thermal analysis or vapor pressure studies. Experimental Methods and Results The phase diagram for the U-Zn system at 1 atrn pressure, shown in Fig. 1, is based primarily on vapor pressure measurements and on thermal analysis taken at temperatures below 950°C. Fig. 2 shows the U-Zn diagram at 5 atrn pressure, constructed on the basis of thermal analysis of alloys in sealed containers up to 1150°C and on the basis of metallographic, X-ray, and analytical data. The alloys sealed under vacuum were actually under their own vapor pressure and those sealed in an atmosphere of helium were under an additional pressure due to the helium. At temperatures up to 1100°C the zinc pressure is 5 atrn or less for these alloys; consequently the maximum pressure over the alloys sealed under a helium atmosphere was 10 atrn or less at temperatures up to 1100°C. Changes in pressure of this order of magnitude do not appreciably alter the position of most solid-solid or liquid-solid phase boundaries. In constructing the phase diagram for a pressure of 5 atm, the effect of pressure on all phase boundaries except those for liquid-vapor or solid-vapor regions was considered negligible.

Jan 1, 1958

By C. A. Wright

The average lead and zinc content of the ores mined and milled in the Joplin district is low as compared with that of other lead and zinc deposits throughout the United States. Because of this fact and of the high grade of the concentrates, the ratio of concentration is unusually high. Most of the operating companies have aimed to produce as high a grade of concentrate as possible in order to obtain the highest price for their product. They have done this at the sacrifice of the percentage of zinc recovered. The average percentage of zinc recovery is from 60 to 70 per cent. For percentage of recoveries from actual mill tests, see tables. The concentration is commonly effected by crushing the ore to ½-in. (12.7 mm.) size and subjecting it to a roughing and cleaning over two or more large Cooley jigs, of the Harz type, the finer sands being treated on the usual types of sand and slime tables. The treatment of slimes by flotation is being tested at several of the larger mills. Coarse Concentration When the ore has been hoisted from the mine it is dumped onto a chute leading to a grizzly made of iron bars, usually heavy rails, spaced 4 to 5 in. (101 to 127 mm.) apart. The oversize is caught on the grizzly, the mineralized pieces are broken with sledge hammers so as to pass through, and the boulders that are practically barren are sorted out by hand and trammed to the waste-rock pile. The proportion of waste rock thus sorted out varies from a fraction of 1 per cent. to 15 per cent., depending on the nature of the rock. Crushing The undersize material, 5 in. (127 mm.) or less in diameter, passes through the openings of the grizzly into the mill hopper below. From

Jan 1, 1918

By Alan Probert

IN his inaugural address in 1949, President Truman made a policy declaration which launched the foreign technical assistance program known to the world as Point Four. Congress passed Public Law 535 defining the scope of the program and holding activities to certain limitations. It also provided $34.5 million for the first fiscal year. The Technical Cooperation Administration was established within the Department of State to coordinate and direct a program to include "economic, engineering, medical, educational, agricultural, fishery, mineral and fiscal surveys, demonstration, training and similar projects." The mineral programs of Point Four have been staffed and managed by two agencies of the Department of Interior, the Geological Survey and the Bureau of Mines. The Geological Survey is concerned primarily with water-supply problems, the discovery of mineral deposits, and the determination of habit, shape, and grade of mineral deposits. The Bureau of Mines is concerned with determining the commercial potentialities of mineral deposits, mineral technology, and the production and distribution of mineral commodities. Mineral projects comprised only 1 pet of the first year's budget. In spite of the relatively insignificant expenditure compared to those for food, agriculture, and health, a commendable record has been achieved.

Jan 1, 1952

By R. C. Dorward

DIFFUSION considerations are necessary to describe many technologically important metallurgical and physical processes. Since most commercially important alloys are comprised of more than two components, diffusion calculations applicable to binary systems are often unjustified. However, in many instances the more general equations valid for three-component systems may be employed. The phenom-enological description of ternary diffusion is now well-established,1-4 and the theory has been applied with some success to a few practical situations.5"7 The flux equations for the solutes (components 1 and 2) of a ternary solution may be expressed by:

Jan 1, 1969

By Shosei Serata

Serious floor heave of up to 2.4 m in a 2.4-m high mine entry was eliminated by applying the stress control method of mining, as a last resort, at the No. 5 coal mine of Jim Walter Resources, Inc., in the Black Warrior coal basin near Birmingham, Alabama. Underground observation of the first 3-room entry created using the stress control method is discussed here. The behavior of the test entry, which eliminated the heave problem, is analyzed in relation to similar studies conducted in a salt mine under similar ground conditions by utilizing finite element analysis.

Jan 1, 1984

By B. R. Eichbaum, J. E. Murphy, J. A. Eisele

The US Bureau of Mines demonstrated ferric chloride leaching of galena concentrate on a continuous bench scale basis. Leaching was performed at 95°C (200°F) and with a contact time of 15 minutes. The ferric chloride leaching solution was continuously fed to a leaching tank at a constant rate for periods up to 45 hours. In each test, a constant redox potential was maintained in the slurry exiting the leaching tank by controlling the concentrate feed rate. In the 45 hour test, lead extraction exceeded 99.5%, and the lead chloride produced was 99.97% pure.

Jan 1, 1986

Belting worth thousands of dollars can be ruined in a few minutes because of careless maintenance or lack of maintenance. Proper belt conveyor maintenance means having a clean conveyor system at all times. The belt line should be visually inspected during each shift. Equipped with proper maintenance instructions, one belt man can patrol a belt line of 2 to 3 km (1.5 to 2 miles). His duties would be to lubricate drives and idlers (except sealed-for- life type), maintain belt and conveyor frame alignment, detect sticking idlers, and maintain an unobstructed right-of-way.

Jan 3, 1978