Search Documents

By Leslie W. Austen

ROTARY kiln operators will agree that some of the most severe conditions a refractory must stand occur in the hot zone of a kiln burning Portland cement, dead burn dolomite, magnesite, peri-clase, and similar materials. Frequently the operator is faced with factors beyond his control which drastically shorten the life of refractories. Shutdown due to mechanical failure can be serious if the period is of sufficiently long duration to cause the dropping of coating or the loosening of the lining. A change in slurry can affect the coating and cause ring buildup. A change in type of fuel and its effect upon the flame can cause a shift in location of the hottest zone. Weekend shutdowns or any other interruption can cause the operator trouble and may damage the refractories, since stopping and starting a rotary kiln is certainly more difficult than stopping and starting a motor. Some operators have tried to set an estimate of damage for each shutdown in equivalent days of running time. Conditions affecting the refractory may be roughly grouped in four classes: chemical attack, mechanical stress, thermal shock, and abrasion. Chemical Attack: The drive to obtain maximum production through a kiln demands maximum operating temperatures, temperatures which are limited more by the ringing up or melting of the clinker. This can cause interface temperatures at the junction of coating and refractory which require the use of a basic kiln block to withstand the chemical attack. Chemical changes take place within the refractory itself, especially in chemically bonded or unburned kiln blocks. These changes cause the formation of the ceramic or burned bond. Migrating liquids or fluxes from the kiln charge have an effect within the refractory and lead to mineral or glass formation. The alkalies, sodium and potassium, migrate into the refractory as silicates, chlorides, sulphates or other salts. They may move under capillary action or may be caused to move by volatilization with condensation in the cooler portion. Mechanical Stress: Concentrated stress may be caused by several factors or combinations thereof. I—The rings of refractories must be kept tight and rigid within the kiln, and this alone demands considerable force to hold the blocks in place. So that the force will not be concentrated, the blocks should fit the circle as perfectly as possible, with the faces in contact overall. 2—As the kiln is heated, thermal expansion takes place at the hot end of the kiln block. Since this disturbs the plane face it too can cause a concentrated stress at the two ends of the block, and shearing stress can be set up within the brick itself because of the difference in expansion between the two ends. 3—If a lining becomes loose and moves in the shell very severe stress can be set up, and as the kiln rotates this load changes and gives the effect of repeated loading. Permanent expansion of the refractory can also cause severe loading. 4—Not least important, flexing of the kiln is frequently the cause of concentrated stresses. Thermal Shock: Thermal shock, the result of heating and cooling too rapidly, occurs on starting and stopping or when a large patch of coating drops, exposing the bricks. Again, its destructive effect is often the result of phase change, liquid to solid or the reverse; dense refractories loaded with glass-forming impurities are particularly susceptible. Thermal shock is a. problem with refractories set in the wall or roof of a stationary furnace, and becomes even more serious in a rotary kiln, the tendency to spa11 being magnified with movement and concentration of stress. Uniform rate of feed and loading insures both better coating and a more uniform stress. Abrasion: If the refractories do not take a coating, abrasion can become a most destructive factor. Movement of the lining in shell or movement of loose blocks causes abrasion, which is also most destructive if the refractories do not take a coating. An analysis of the problem of basic lining for the hot zone reveals, therefore, a number of desirable characteristics: high refractoriness, basic chemical reaction, resistance to spalling, good strength at all stages, ability to take coating, true sizing, volume stability, and abrasion resistance. Increased demand

Jan 1, 1953

By Paul Weir

BLEACHING clays have been used extensively in the oil-refining industries for a number of years. Their use in water purification is relatively recent and less extensive. They are frequently classified as (1) those naturally active and (2) those active after artificial activation with acid. Fuller's earths fall within the general group of bleaching clays and gradually the commercial term "fuller's earth" has been applied to natural clays originating, for the most part, in the south-eastern section of the United States. Bentonitic clays are usually classed as activable and are prevalent in the southwestern section of the United States.1 Bleaching clays vary considerably in chemical and physical properties throughout the country, or even in different parts of one deposit (Table 1). TABLE 1.-Physical and Chemical Composition of Different Types of Clays Composition, Per Cent Constituents and Properties Bentonite Fuller's Mud Clay (Wyoming) Earth (P Peak)' (Alluvial) Silica (SiO2) 60.0 69.6 61.67 Alumina (Al203) 19.0 14.3 20.34 Ferric oxide (Fe203) 2.8 3.90 7.70 Titanium oxide (Ti02) 0.13 0.70 1.01 Lime (CaO) 0.5 0.80 0.00 Magnesia (MgO) 2.0 1.00 0.24 Soda (Na2O) 2.4 0.40 0.31 Ignition loss 4.7 6.77 8.51 Moisture content 8.0 10.0 20.0 Isoelectric point, pH 9.2 9.2 6.5 Average swelling volume 15.0 0.0 0.0 Weight per cubic foot, lb 55.0 40.0 65.0 Material passing 200-mesh sieve, per cent 90.0 85.0 50.0

Jan 1, 1939

By H. L. Miaw, A. M. Gaudin, D. W. Fuerstenau

IN spite of considerable study,1-5 the nature of slime coatings in flotation is still not completely understood. However, phenomena that control flocculation and dispersion of colloidal systems are now interpreted in terms of electrical double layers."' Colloids will flocculate even though the particles carry the same charge, but when two dispersed colloids of opposite charge are mixed, flocculation ensues even more rapidly. Analogous phenomena seem responsible for slime coating on minerals in flotation systems. To shed new light on the issue it was considered desirable to devise a tool that would measure slime coatings. The usual method has been to examine photographs of presumably representative surfaces, after an intervening washing in running water. But such an examination is non-quantitative, and the changes in chemical environment represented by the washing may have removed the slime coatings that existed during flotation. To provide the possibility for a correlation with electrical double layer phenomena, the experiments were made with quartz, corundum, and iron oxide, for which electrokinetic data are available.8-12 Since the properties of the electrical double layers of these oxides depend on the pH of the solution, pH will be the most important variable. Furthermore, because the zero point of charge for silica, iron oxide, and alumina occurs at pH 3.7, 8, and 9.5, respectively, the relative charge on the slime and mineral can be changed over wide ranges. Because of its practical importance in quartz flotation, iron oxide powder was chosen as the slime. Also, its uniform composition, contrasting color, and ease of analysis make experimentation simple.

Jan 7, 1958

By J. J. Oberly

WHILE examining lineage boundaries in germanium single crystals as described by Vogel et al.,&apos; patterns of conical etch pits were noted which reveal interesting properties of dislocations. The crystals were grown by pulling in the <100> direction, and (100) surfaces perpendicular to the growth direction were etched 4 min in a mixture of 6 cu cm HF, 10 cu cm HNO3, 6 cu cm acetic acid, 3 drops Br,. Lineage boundaries extended in any direction, but favored the <110> direction. The patterns which were noted first were composed of two or three etch pits arranged symmetrically about the lineage boundary, so that the doublets were spaced equally on either side of the boundary line and the triplets had their center pit on the boundary line. The triplets occurred less often than did the doublets; occasionally combinations were found. Two such combination patterns are shown in Figs. 1 and 2. The orientation of the patterns was determined approximately by subsequently etching the same surfaces in a mixture of 5 cu cm HF, 5 cu cm super-0x01, and 20 cu cm distilled water which produced nearby random square etch pits having edges in the <110> direction. In all cases, the axis of symmetry was <110>, being parallel to the etch-pit edges. Several successive lapping and etching operations showed that the patterns tended to continue through the crystal in the <100> direction, but eventually changed or vanished. It can be seen in both photographs that the pits in the patterns are much further apart than the pits in the adjacent section of the lineage boundary. In Fig. 1, the 10 pits of the pat-

Jan 1, 1955

By Henry A. Pohs

It is a rare work of art that attains the proportions of a major construction project. One instance of such a phenomenon is Bartholdi&apos;s Miss Liberty, which was designed and built section by section in Paris and then erected in New York Harbor. Another is Borglum&apos;s massive presidential quartet hewn from the granite of Mount Rushmore. Now, however, there is a new monument in the making which will completely dwarf all others. The sculptor of this supercolossus is Korczak Ziolkowski, a colorful, bearded genius who assisted Borglum on Mount Rushmore and is now carving his own granite masterpiece from Thunderhead Mountain near Custer, S. D., just ten crow-flight miles away from Rushmore.

Jan 11, 1966

An overland belt conveyor system installed at Simco-Peabody&apos;s mine near Coshocton, Ohio, is presently carrying coal three miles at an estimated cost of 4.499 per ton-mile. Installed by Link-Belt Co. in late 1961, this system transports coal from open pit and underground mining operations to the Conesville Power Plant. Simco-Peabody has mining operations over a considerable area just east of the Conesville Station. In 1960 the power plant completed plans to enlarge by adding a third boiler. As a result, Simco-Peabody was required to provide means to produce and handle more coal. The haulage equipment, which consisted of one 90-ton, five 60-ton and one 50-ton off- highway trucks, was too small to handle the increasing daily coal demands. Annual tonnage was approaching a million tons and in a few years would be well over that figure.

Jan 4, 1963

By Gregory B. Baecher

Rock engineering involves uncertainties which are large and difficult to quantify. The traditional design approach to these uncertain- ties has been conservatism, and has been satisfactory to the extent that failure rates are reasonably small. Yet, a price is paid for conservatism, and that price is not always small. Today, reliability and risk analysis are finding use in rock engineering. The introduction of such methods, usually under the name &apos;probabilistic design,&apos; is controverisal. However, if the jingoism of both sizes in this controversy is stripped away, it appears that new insights about uncertainty in rock engineering are emerging.

Jan 1, 1982

By Robert Uhley, Tsvi Meidav, LeRoy Scharon

Before National Lead built an industrial plant on its Fredricktown property, some 100 miles south of St. Louis, a 750x500-ft area on the proposed site was investigated by electrical resistivity, seismic refraction, and churn drilling. Data were accumulated to prepare an isopach map of the overburden and to determine soundness of the dolomite bed- rock and the depth to bedrock at fixed points. The site was on a gently sloping hillside. Elevations above sea level ranged from 760 ft in the northwest corner to 820 ft along the eastern edge, giving a total relief of 60 ft. There were no major drainage features, but in the northern part of the plant site there was an indicated depression area which later was interpreted as reflecting subsurface conditions in the bedrock. No rock was exposed in the entire plant site area; the surface was characterized by soil and overburden.

Jan 2, 1959

By Howard M. Graff, Sidney C. Bouwer

The economics of mining has traditionally been viewed quite apart from the economics of blast furnace operations. It was realized, of course, that blast furnaces would operate best with good raw materials, but the shipping grade of ore, for example, was decided by a sort of collective bargaining process between the ore producers and the blast furnace operators. The mine operators had to keep their costs down, and were usually successful in convincing management that the ore in any particular deposit was endowed by nature with a certain iron content and that the mine grade could not be raised beyond a certain economic limit. The blast furnace operators would have liked a better grade, but as long as they were able to make a fairly good showing it was more or less accepted that they had to take the ore as it came. The mine operators were able to ship to the nation&apos;s blast furnaces thousands of tons of iron ore that would be completely unacceptable by present-day standards. As late as the early 1950&apos;s, the major steel companies were witnessing an actual decline in the iron content of their incoming ore supply as the mining companies mined progressively leaner material and upgraded it only enough to pass competitive market requirements

Jan 8, 1965

By AIME AIME

HOLDING the annual dinner-dance of the Institute at the Waldorf-Astoria had become such a tradition that there was widespread regret when it became known that the demolition of the building to make way for a huge office structure would perforce bring to an end the long and enjoyable series of gatherings our Institute had held there. This year the . Commodore was the place at which it was held and the commuters on the New York Central and the New Haven railroad systems, at least, found it a more convenient place for them. Except for the famous "Hoover" dinner, which will probably set a mark for all time, it was the largest dinner the Institute held, 1000 being present, and it taxed the facilities of the hotel to the utmost.

Jan 1, 1930

By David L. Rife

Fluid inclusions have been studied since the mid-1800s. In 1858, the famous English geologist H. C. Sorby, stated that ". . . there is no necessary connection between the size of an object and the value of a fact, and that, though the objects [inclusions] ... are minute, the conclusions to be derived from the facts are great."&apos; This statement philosophically emphasizes why fluid inclusions should be studied. Fluid inclusions supply the economic geologist with "hard" data on the chemical environment and mechanisms of transport for ore fluids. Such studies enable geologists to understand more about their complex nature. The information that can be obtained from fluid inclusions is as follows: 1) Fluid inclusion "filling temperatures" measured with the microscope heating stage, reflect the hotness of an ore fluid at the time of its entrapment and are one of the most accurate methods of geologic thermometry. 2) Ore fluid densities indicate the extent to which ground water becomes mixed with ore fluids. Density is determined from the composition of inclusions, the ratios of gas to liquid (at room temperature), and from

Jan 1, 1973

By A. E. Bellis

The time effect in reheating certain steels below the critical range is very marked. The increased toughness, shock-resisting power, and machinability of steel subjected to a long, high drawing temperature has been thoroughly demonstrated and is of practical importance, particularly in the manufacture of L&apos;smokeless" rifle-barrel steel. The time effect in tempering is most important when a maximum drawing effect is desired, in which case the highest physical properties as well as ease of machining are important considerations. These are the conditions in drilling a rifle barrel. A hole, 0.30 in. in diameter and 24 in. long for the Springfield rifle, and 30 in. long for the Russian military rifle, has to be drilled in the heat-treated material. This barrel-drilling operation is probably the most difficult one in rifle manufacture, and anyone who has been connected with rifle manufacture knows how seriously production is affected when "hard" or non-uniform steel for barrels is encountered. The importance of high physical properties (tensile strength, toughness and resilience) in a rifle barrel is obvious. The physical properties of two different lots of barrel steel are given below. The first lot, No. 1, gave serious trouble in the drilling operation; the second gave no trouble at all. No. 1 No. 2 Elastic limit, lb. per sq. in.................... 117,450 116,800 Tensile strength, Ib. per sq. in................. 132,500 131,750 Elongation, per cent........................ 16.0 20.0 Reduction of area, per cent................... 42.1 51.0 Impact strength, ft.-lb. per sq. in.............. 450.0 520.0 This difference in machining and physical properties was due entirely to the time of reheating. The first lot was given a reheating time of 30 min., the second lot remained at the reheating temperature 2 hr. Both

Jan 1, 1918

By George S. Rice

INTERESTING developments going on in European coal mines look to: (1) increasing mechanization; 12) concentration of mining; (3) improvement in safety appliances; and (4) studies in bettering roof supports and. incident to this, studies of the way a roof behaves under different conditions of support and methods of mining and back-filling. Mechanization and concentration off mining is being adapted to a considerable extent in Great Britain coincident with the development of conveyors. Belt conveyors, shaker-pan conveyors, and a combination of the two are used. For pitching seams not steep enough for the coal to run in station-chutes, the. shaker-pan conveyor is more popular. For large outputs from a contiguous face, the double-unit system of face layout-that is, the conveyors meeting at a common point-is favored.

Jan 1, 1934

By AIME AIME

PERHAPS the most interesting paper of the subsidence session on Monday morning was that by Roland D. Parks entitled "Yieldable Metal Props for Underground Support." This paper described the development of a telescoping prop made from two pieces of pipe. The lower and larger in diameter has cast in it a soft metallic alloy which is slowly extruded through an orifice in the upper and smaller piece of pipe. In this way, the length of the prop decreases gradually as the load from the roof increases. The stress-strain diagram for these props, as tested in the laboratory, is almost ideal, and can be duplicated satisfactorily in successive tests. They have not yet been tested underground. Another paper of much interest was presented by Prof. P. B. Bucky. It is an addition to his series on structural models as applied to mining and was entitled "Effect of Approximately Vertical Cracks in the Behavior of Hori¬zontally Lying Roof Strata." It was illustrated by motion pictures of a model under test. After explaining the un¬derlying theory, the apparatus and the mode of testing, Prof. Bucky set forth the effect of vertical cracks in a mine roof, as follows: (a) the wider the crack, the weaker the roof; (b) where the sides of the crack are in juxtaposition, there is little weakening of the roof; (c) grouting cracks whose sides are not in contact restores the strength of the roof until it may be as strong as, or stronger than the uncracked roof. Small paper props helped sustain the roof. Both the nature of the material and its bonding affect its behavior under stress.

Jan 1, 1933

By James M. Townsend

INTRODUCTION The first stage in planning any mining venture is to determine whether the reserves are of sufficient quantity and quality to warrant commencement of mining activities. In addition to total reserve values a modern mining operation requires information on possible support problems, various pillar sizes, and an estimate on recoverable reserves. To achieve this goal in U. S. coal mines, up-to-date computer methods have been applied to existing ground control technology to provide the mining engineer with a reasonably accurate method of determining such figures. The purpose of this paper is to present a mine planning suite comprised of three computer programs, CONTUR, RESERV-COAL and RAMPLAN, created to accomplish this task. These programs were developed at VPI under the sponsorship of the Office of Coal Research (now Energy Research and Development Administration), and are currently available to the mining industry. A basic assumption in the construction of the CONTUR program is that a coal seam is variable in nature. The data available to the mining engineer comes from randomly spaced points, namely boreholes and sampling points, on outcrops or in adjacent mines. These randomly spaced data points are used in the CONTUR program to estimate numerical values at evenly spaced grid points and to provide approximate contour plans. Given the necessary gridded data, RESERV-COAL calculates raw and clean coal tonnages and then provides breakdown on the quantity of coal within specified ranges of ash, sulfur, BTU and reject. RAMPLAN (Rock Mechanics Applied to Mine Planning) also uses gridded data to calculate mining dimensions and estimate recoverable reserves, thereby

Jan 1, 1977

By L. C. Snider

NO important discoveries of petroleum during 1932 are reported from Canada. New Brunswick, which has a small production from one field, was inactive, and the production showed a decline from 6600 bbl. in 1931 to about 6300 bbl. for the year 1932. The old fields in Ontario increased from 123,000 to about 131,000 bbl. Alberta showed a decline of more than one-third, from 1,413,631 bbl. in 1931 to about 913,000 bbl. in 1932. This decline was due principally to the restrictions placed on the flow of gas wells in the Turner Valley field, from which the crude naphtha is obtained that accounted for more than 93 per cent of the production of Alberta and for more than 80 per cent of the production of all Canada in 1932. The starting of new wells to the limestone that produces the naphtha-bearing gas was prohibited late in 1931, and only wells started before that time were finished during 1932. One well was drilled in the Turner Valley field to a depth of 7555 ft., establishing a depth record for Canada. It passed out of the Madison limestone at 5560 ft., and encountered showings of oil in the underlying formations, probably of Devonian age. Commercial production had not been established by the end of the year. Commercial oil wells were brought in in two areas in Ontario which had previously been considered as productive of gas only— in the Dawn gas field, Lambton County, and in Raleigh Township, Kent County. The discovery wells had initial productions of about 50 bbl. per day, but no production of major importance is indicated. In Alberta, outside the Turner Valley district, two wildcats were drilled northwest. of Lethbridge in the Keho Lake vicinity. Both failed to make commercial producers in the Madison limestone, but one was testing upper sands at the close of the year. Good showings of oil are reported. A very small production was found in the Madison limestone in a wildcat well on the Twin River structure southeast of Lethbridge and another well has been started near by on what is considered on geophysical evidence to be a better location structurally. About 15 locations were made on the Canadian side of the border north of the Cut Bank development in Montana.

Jan 1, 1933

By M. E. Fine, A. A. Hendrickson

The critical resolved shear stress and the strain rate dependence of the .flow stress are reported for Ag base A1 single crystals up to 6 at. pct A1 over a temperature ralzge of 4.1° to 470°K. At room temperature the solid solution strengthening is attributed brinciballv to an increase in the dislocation density on alloying. At 42°K the alloys are relatively stronger because the dislocations widen on alloying and are more difficult to cut. In a previous paper, the authors reported the characteristics of strain aging in Ag base A1 alloys.&apos; The variation of the magnitude of the strain-aging yield drops on aging time, aluminum content, and testing temperature strongly indicated that the phenomenon is due to the Suzuki mechanism. In the present paper, the critical resolved shear stress (CRSS) and the strain rate dependence of the flow stress are reported for Ag base A1 single crystals as functions of testing temperature (4.2" to 470") and A1 content (0 to 6 at. pct). Observations on the substructure and measurements of the effect of crystal growth rate are also given. The experimental re- sults appear explainable considering that aluminum additions increase the dislocation density and dislocation width. EXPERIMENTAL METHOD The methods of specimen preparation and tensile testing were described previously.&apos; Briefly, single crystals were grown from the melt in a vacuum (1 x lom5 mm Hg), shaped into tensile samples by a combination of abrading and acid etching, annealed at 850°C in a vacuum (1 x 10" mm &Z) for several days, and furnace cooled to 200&apos;. The testing was done on a model TM Instron using friction grips and a strain rate of about 5 x 106 per sec unless otherwise noted. The various testing temperatures were obtained by immersing the specimens in the following media: 1) 4.2&apos;: liquid helium using the apparatus of G. Byrne;&apos; 2) 77°K: liquid nitrogen; 3) 200"K: dry ice and acetone; 4) 415&apos; K: ethylene glycol; 5) 460&apos; \ to 480&apos; : molten Stanalax. In the determination of the CRSS above 296&apos; K, a ratio method was used; the crystals were strained initially at the higher temperature, 0.1 pct shear strain, and then tested at 296&apos; . The ratio of the flow stress between the two temperatures was then multiplied by the average CRSS at 296&apos; K to obtain the value of the CRSS at the high temperature. (The test at 296&apos; showed a yield point resulting from strain aging; the flow stress at 296&apos; K was taken as the lower yield stress.) The ratio method, we believe, is more accurate than using different crystals since

Jan 1, 1962

By Walter Crafts, C. M. Offenhauer

IN the course of study of the heat-treatment of low-alloy steels, the behavior of alloy carbides at subcritical temperatures was found to vary from that indicated by published investigations. In order to establish the ranges of formation of carbides in low-chromium steels, a series of steels containing up to 0.60 per cent carbon and 7.5 per cent chromium has been investigated with respect to the type of carbide formed after quenching and tempering at subcritical temperatures. The types of carbide formed as products of austenite transformation to pearlitic and pseudomartensitic structures have also been determined. There have been numerous investigations of the carbides in chromium steels and diagrams of the iron-chromium-carbon system.1 Westgren, Phragmén and Negresco2 identified the following carbides in chromium steels: [Cementite Fe3C (containing up to about 15 per cent Cr) Trigonal carbide Cr7C3 (containing up to about 55 per cent Fe) Cubic carbide Cr4C (or Cr23C3) (containing up to about 25 per cent Fe) Orthorhombic carbide . Cr3C2 (containing only a few per cent Fe)] The most complete information on the iron-chromium-carbon system was supplied by Tofaute, Sponheuer and Bennek3 and by Tofaute, Küttner and Büttinghaus.4 By means of dilatometric and microscopic studies, sections of the diagram were established. This diagram showed the presence of the special carbide Cr7Ca in steels containing about 2.5 per cent to 12 per cent chromium in low-carbon steels and from about 5 to 20 per cent chromium in r per cent carbon alloys from A1 to room temperature. The present investigation has shown that a carbide inversion from Fe3C to Cr7Ca occurs in chromium steels containing more than about 1 per cent chromium after hardening and tempering at subcritical temperatures above about 500°C. The type of carbide observed to be more stable in quenched and tempered specimens was also found to be produced by direct austenite transformation in corresponding ranges of temperature and composition. EXPERIMENTAL PROCEDURE The steels used in these experiments were made in magnesia-lined crucibles in high-frequency furnaces and were poured into 2-in. ingots. The ingots were forged into 1-in. round bars, and all heat-treatments were conducted on specimens of this section .size. Sections of the bar stock 8 in. long were hardened in air, oil or water depending on the composition, after heating to a temperature sufficiently high to dissolve the carbides. The low-carbon and low-chromium steels were not entirely martensitic after quenching, and contained some ferrite and pseudomartensite. No pearlite was observed in the microstructures after auenchine. The quenched bars were cut into

Jan 1, 1942

By J. O. Betterton, W. M. Spicer

The solubilities of antimony in the a and ß-forms of zirconium were determined between 750" and 1300°C. The a-phase forms by a peritectoid reaction, and the a/(a + ß) and ß/(a + ß) phase boundaries rise in temperature with in- &apos; creasing antimony. Impurities in the 99.95 pct zirconium were sufficient to influence the phase boundaries and the variation reported is approximate. The restricted solid solubility of the terminal zirconium phases, which is especially characteristic of this system, is thought to result from the low free energy of the Zr2Sb phase. ZIRCONIUM-antimony alloys are important in zirconium alloying studies since antimony is one of the highest valent elements which can be used to make zirconium alloys. The dilute alloys are of further interest as they have somewhat better corrosion resistance&apos; than pure zirconium. The first investigation of the phase diagram was made by Russi and wilhelm2 who found a eutectic reaction, liquid (- 17.5 at. pct Sb) = ß zirconium (- 11 at. pct Sb) + Zr2Sb, at 1430°C&apos;. The Zr2Sb phase was of complicated hexagonal structure, and by thermal analyses of the relatively impure alloys then available, Russi and Wilhelm found evidence for the peritectoid formation of the a-phase. EXPERIMENTAL In the present work, the phase diagram was re-investigated in the region 0 to 5 at. pct Sb and 750" to 1300°C using iodide-zirconium alloys. Details of the procedure have been described earlier. Essentially the alloys were prepared by arc casting and were then examined by the annealing and quenching method. The times of annealing varied from 1 hr at 1300°C to 30 days at 760°C. As in other zirconium phase-diagram studies1"5 the impurities in the zirconium were still sufficient to affect the results, and the experiments will therefore be described in 3 parts. The results from the first 2 parts of the work are shown in Fig. 1. Here the ß/(ß + Zr2Sb) and a/(a + ZrzSb) phase boundaries were determined with alloys made from 99.9 pct zirconium,* and cast under such conditions that the Vickers hardness of a alloys extrapolated to 95 to 110 VPN at 0 at. pct Sb. Such alloys were not suitable for investigations of the (a + ß) region, and the results shown in Fig. 1 near the (a+ ß) and (a +ß + Zr2Sb) regions were determined with purer alloys. These alloys had an extrapolated hardness range of 75 to 85 VPN and were made from 99.95 pct zirconium. A deviation from binary equilibrium occurs in Fig. 1 as indicated by the (a + ß) region of pure

Jan 1, 1959

By W. E. Horst

Flotation feed was hell constant for batch laboratory tests and continuous pilot and commercial plant tests on a spodumene ore to determine the relation.ship between flotation behavior and the size and type of flotation machine. Results. showed that additional retention time would be needed in the plant flotation circuit to duplicate laboratory or pilot plant performance when operating Dariables of the. plant flotation machines remained unchanged. During the past few years of operation at Kings Mountain, N. C., full-scale flotation has generally yielded poorer metallurgical results than those obtained in the laboratory or pilot plant. After 2 min in each size of Denver flotation machine in the spodumene rougher circuit, pilot recovery (41.7 pct) was almost three times that of the plant (13.6 pct) and about twice that of the laboratory (21.0 pct). Pilot and commercial plant data are based on continuous operation, and laboratory results on batch testing of rougher performance. The ore is a pegmatite containing spodumene, feldspar, quartz, mica, and amphibolite. Data were accumulated to evaluate the scale-up relationships between laboratory, pilot plant, and plant flotation cells. Flotation rate constants and dimensional analysis were used to define the relationship existing between flotation behavior and scale of operation. Measuring Flotation Rates: Efficiency of the rougher stage was measured by flotation rate, defined as the recovery that can be attained within a given time." • The problem of measuring flotation rates has been studied by many investigators, whose methods have varied. Published studies an flotation kinetics have been summarized recently by Gaudin.l When comparing flotation rates, it is more satisfactory to compare straight line relationships between recovery and flotation time than exponential curves resulting from plotting cumulative recovery vs cumulative flotation time. To convert the exponential curves into straight line relationships, rate equations were applied similar to those used in chemical kinetics to study the velocity of chemical reactions. Two rate equations have been used in this investigation to measure efficiency of the various cells: 1.5 order Rate Equation dR/dt=k (A-R)1.0 [Eq.1] Second Order Rate Equation dR ---- - K(A - R)2 [Eq. 2] dt Upon integration Eq. 1 becomes 1/(A-R)1/2=k/2 t+1/A1/2 [Eq. 3] and Eq 2 becomes: or fEq. 4] t/R=1/A2K+t/A [Eq. 4] where R = cumulative recovery [percent recovery of total value (spodumene) in flotation feed]. A = initial concentration, pct (100 pct of mineral to be separated). t = flotation time (minutes). k = flotation rate constant for 1.5 order rate equation [units: 1/(percent) 0.5 (min)1. K = flotation rate constant for second order rate equation [units: 1/(percent) (min) 1.

Jan 1, 1959