Search Documents

By D. L. Martin, E. R. Parker

IN a previous paper, one of the authors observed that the rate of cooling from the anneal prior to testing greatly influenced the life of copper under sustained load at 200°C. Furnace-cooled bars of oxygen-free copper (with, and without silver) had a life four to twenty-five times that of the water-quenched specimens. The addition of 0.054 per cent silver to the oxygen-free copper increased the life at a stress of 20,000 lb. per sq. in. from about 2 hr. to 50 hr. Fractures in these bars were intercrystalline. An explanation was advanced to account for the profound influence of cooling rate on the rupture properties at 200°C. The suggestion offered was that at the high annealing temperature the minor constituents are distributed at random. By water quenching, this condition is maintained at room temperature, whereas furnace cooling permits some segregation at the grain boundaries. The higher concentration of the minor constituents in the grain boundaries results in a strengthening, so that a longer life at a given stress and temperature results. Small amounts of cadmium or manganese have also been found to increase the life of copper at 200°C., and to a much greater extent than silver .2 The increase in the long-time strength of copper resulting from small additions of cadmium or silver appears to be related, indirectly at least, to the higher softening temperatures of such alloys. The elements, such as silver or cadmium, which greatly increase the rupture life of copper also cause large increases in the softening temperature. As little as 0.05 per cent of cadmium or silver is sufficient to raise the softening temperature more than 100°.3,4 The effects of cooling rate and of minor constituents on the rupture properties are of considerable fundamental as well as practical interest; therefore a more detailed study of their nature was conducted and is reported in this paper. EXPERIMENTAL PROCEDURE Materials The materials studied in this investigation may conveniently be classified in two groups: one consisting of a wide variety of commercial coppers, and the other composed of special high-purity, laboratory-prepared coppers. The commercial materials were tested to determine whether or not the effect of cooling rate occurred with all coppers, whereas the high-purity coppers were investigated in order to establish a basis for evaluating the effect of minor constituents on the rupture properties. In Table I are given the analyses of the coppers tested. The samples I to 6 are commercial materials and were obtained for the most part from stock supplies.*

Jan 1, 1943

By John Randall

It is a fair assumption that the main purpose of any diagram is to present facts to the eye in more convenient form than they could be tabulated in figures, and this implies that a screen diagram should set forth in a convenient and familiar form certain facts as to the character of the material screened regardless of the screen standards used, and it seems particularly desirable on account of the well-known differences in the size of openings of different laboratory screens having the same nominal mesh. In making screen-sizing tests it has been customary first to consider the largest size, going progressively to the smallest, and this seems to have led to the practice of placing the smallest size .at the right-hand side of the diagram and measuring toward the left. This is not altogether convenient and might be changed to advantage, but for illustration I have preserved that feature and present the method just as I have used it for over 2 years. Direct plotting in which the intervals on the diagram are proportional to the sizes of the openings, or to the arithmetical difference between them, seems at first sight more natural and is extremely useful for certain purposes, but it makes the diagram very crowded in the smaller screen sizes while the larger ones occupy unnecessary space, making it less convenient for most purposes, and for that reason the method here discussed is the well-known one based on the ratio between openings, and is plotted in logarithms instead of the direct values of the screen opening. Metric coordinate paper is convenient, although not necessary; it is recommended, as the use of the metric scale gives a diagram of convenient size, but any scale of equal parts may be used. In order to make any screen diagram translatable in terms of any standard screen size, it is necessary to have noted on the size scale of the diagram all points corresponding to the openings of the various screens in question, instead of a single series of points as with a single screen. In drawing the diagram assume 0.001 in. (corresponding approximately to 0.025 mm.) to be the smallest size to be considered and fix this as the zero point at the lower right-hand corner of the diagram. This value is selected because the values are to be plotted in logarithms, and the logarithm of 1 is zero. Then lay off to the left for the position of each screen

Jan 1, 1918

By Karl L. Konnerth

THE rapidly increasing use of machinery for the mining of coal and operations incidental thereto has materially changed conditions from a safety standpoint. A few of the coal-producing states have recognized the need for specialized electrical equipment for use in mines and have introduced certain requirements in their State safety regulations, notably Pennsylvania. This paper discusses the principal problems involved in maintenance of such equipment. PERMISSIBLE: EQUIPMENT "Permissible" electrical equipment is equipment that has met certain prescribed standards for use in mines where hazardous conditions may occur and has been recommended by the U. S. Bureau of Mines. Such machinery is available on the market for most coal-mining operations--for instance, coal cutting, transportation, drilling, loading, working-place illumination, shot-firing and pumping. A notable exception is the trolley-reel gathering locomotive which, although its parts may be explosion-tested by the Bureau, has not been approved as permissible for the following reasons: I. The trailing cable is subjected to more severe service than on other equipment. 2. State regulations do not require that a working place be examined for methane before a locomotive enters it. 3. Even with two-conductor cable, imperfect or inadequate bonding may cause the emission of sparks at the wheels of the locomotive and at rail joints. 4. As the locomotive is equipped with a trolley pole, and as the trolley wire may be installed and used in unsafe territory in spite of rigid State regulations, a trolley-reel gathering locomotive is always a potential hazard. MAINTENANCE The proper procedure for maintenance of permissible equipment may be divided into three parts: (I) inspection, (2) actual maintenance and (3) changes or improvements to existing machines. To secure the fullest benefits through the use of permissible equipment it is necessary that all men involved understand the principles underlying the safety features of this equipment and realize the significance of defects, so that neglect and indifference in the maintenance thereof may be eliminated. Inspection From the standpoint of safety it is desirable no doubt to make a suitable inspection of permissible electrical equipment once a week, but the opening of every enclosed compartment at each inspection may do more harm than good. The openings to such compartments are closed with various types of covers very accurately machined, often made of the softer alloys to reduce weight, and fastened with a multitude of bolts, screws, washers, and other small parts. Frequent handling of these covers may cause sufficient damage to defeat their original purpose and intent.

Jan 1, 1941

By John Randall

IT is a fair assumption that the main purpose of any diagram is to present facts to the eye in more convenient form than they could be tabulated in figures, and this implies that a screen diagram should set forth in a convenient and familiar form certain facts as to the character of the material screened regardless. of the screen standards used, and it seems particularly desirable on account of the well-known differences in the size of openings of different laboratory screens having the same nominal mesh. In making screen-sizing tests it has been customary to first consider the largest size, going progressively to the smallest, and this seems to have led to the practice of placing the smallest size at the right-hand side of the diagram and .measuring toward the left. This is not altogether convenient and might he changed to advantage, but for illustration I have preserved that feature and present the method just as I have used it for over 2 years. Direct plotting in which the intervals on the diagram are proportional to the sizes of the openings, or to the arithmetical difference between them, seems at first sight more natural and is extremely useful for certain purposes, but it makes the diagram very crowded in the smaller screen sizes while the larger ones occupy unnecessary space, snaking it less convenient for most purposes, and for that reason the method here discussed is the well-known one based oil the ratio between openings, and is plotted in logarithms instead of the direct values of the screen opening. Metric coordinate paper is convenient, although .not necessary; it is recommended, as the use of the metric scale gives a diagram of convenient size, but any scale of equal. parts may be used. In order to make any screen diagram translatable in terms of any standard screen size, it is necessary to have rioted on the size scale of the diagram all points corresponding to the openings of the various screens in question, instead of a single series 'of points as with a single screen. In drawing the diagram assume 0.001 in. (corresponding approximately to 0.025 mm.) to be the smallest size to be considered and fix this as the zero point at the lower right-hand corner of the diagram. This value is selected because the values are to be plotted in logarithms, and the logarithm of 1 is zero. Then lay off to the left for the position of each screen

Jan 9, 1917

By T. A. Klinefelter, R. G. O’Meara, Glenn C. Truesdell, Richard W. Smith

THE investigation of domestic tales was undertaken by the Bureau of Mines, Department of the Interior, in cooperation with the University of Alabama, at the request of the U. S. Army, on Dec. I, 1941: "Considerable concern has been expressed by the Supply Arms and Service over maintaining continued availability of supplies of the necessary raw materials. These ceramic products are used by the Signal Corps in all army radio equipment, and to a greater degree in the new ultra-high-frequency equipment. The Air Corps has become a user of large amounts of radio-grade ceramics for aircraft spark-plug covers required for high-altitude operations. In addition, the use of this material is essential to the proper functioning of the radio air-navigation aids of the Civil Aeronautics Board." HISTORY The use of steatite and talc in ceramic bodies goes back a great many years. If pure, tales shrink little under heat-treatment and are very resistant to heat shock. The massive form, commonly called "steatite" by the trade, cuts and works easily, and this was naturally the first method used in obtaining articles of talc. When gas was in general use for illuminating purposes, a large business was carried on in the manufacture of tips for gas burners.1 With the development of uses for electricity, low-tension insulators were made in a similar manner; and, in fact, the forming of shapes from massive talc continues. However, as the business increased, cuttings and waste became more and more of a problem. In the twenties, one of the larger producing firms had a cooperative agreement with the Bureau of Mines at its Columbus station to work out a body using the finely powdered material. Somewhat earlier, manufacturers of spark plugs used the finely ground talc as part of the body and to some extent in wall-tile bodies. Somewhat later it came into use for kiln furniture and similar products and still more recently it has been used in some dinnerwares. With the development of the radio and the high-frequency fields generated, it was found that a dense steatite porcelain was far better than even high-tension electrical porcelain, which is a clay-flint-feldspathic type of body. Until the war increased the demand, the several pioneer steatite-porcelain manufacturers were able to furnish adequate supplies. When war began in Europe and Asia, three important foreign sources of raw material were cut off; i.e., the French, Italian, and Manchurian tales. Domestic producers of high-grade porcelain are few, and the trade

Jan 1, 1943

By D. A. Woodford

A number of observations have now been reported where the steady-state creep rate is apparently linearly dependent on the applied stress at high temperature and low stresses. This results in a creep rate greater than that predicted by extrapolation of high-stress data and has obvious practical implications. However, some of these observations are open to question. For example, the analysis by Harris and Partridge17 of the data of Greenfield et a1.18 was dependent on strain rates which, according to the original authors, were too low to be measured. Dr. Bernstein appears to have demonstrated a linear stress dependence at low stresses in two zirconium alloys. There are, however, a number of discrepancies in his treatment of the data and the subsequent theoretical analysis which require clarification. 1) It is incorrectly stated that steady-state conditions are revealed by a slope of unity on a plot of log i vs log (time). This objection is trivial if the author meant to say a slope of zero, although it is unclear how subsequent extrapolation was made to determine the steady-state creep rates at low stresses for the zircaloy-2. If the plot used was actually log c vs log (time), it is unlikely that a slope of unity would represent a constant creep rate. A plot of log (c - co) vs log (time), where c0 is the extrapolated intercept sf the steady-state creep rate on the strain axis, would have a slope of unity during steady-state creep. However, eo cannot be determined unless is is already known. 2) The author chooses to interpret his results based on the equation: where A, and B, are structure-sensitive parameters, Ql and Q, are the activation energies for the particular creep process, and n describes the sensitivity of the creep rate on stress. The first term represents a slip creep process and the second a diffusion creep process. However, it is stated later that "two distinct processes acting in parallel are involved". Eq. [I] surely represents two processes in series since each reacts to the total applied stress and t, is the sum of the individual creep rates. If the processes are acting in parallel, then the effective stress in each would be less than the applied stress. The component stresses would be given by sl + s2 = a but it is not clear how the magnitude of either, or the corresponding stress exponent, could be determined.

Jan 1, 1969

By B. M. Larsen, T. E. Brower

THIS discussion is based on statistical manipulation and evaluation of operating data from several commercial blast furnaces which include rather wide variations in practice. We are concerned here mainly with the effect of manganese on sulphur elimination under operating conditions in commercial blast furnaces, but this effect can be outlined more clearly by including certain other variables such as silicon in iron and slag basicity, which are all in part interrelated. Real progress in understanding all of the smelting-zone reactions in this process requires more laboratory studies of slag-metal melts similar to those in the blast furnace, with careful control of oxygen pressure. Such experimental work is very difficult, however, and in the meantime, with the present scarcity of more fundamental data, such statistical trends and correlations as can be obtained from commercial furnace operating records may help in choosing laboratory test conditions as well as adding to our knowledge of operating procedures. We do not know just why the furnace data are apparently so irregular that statistical treatment of large numbers is needed to obtain accurate trends. It is partly caused, no doubt, by the many simultaneous variables present, but there are perhaps also such factors as: (I) the con- tinual swings up and down so characteristic of the process; (2) difficulty of accurate sampling of co-existing phases, as well as (3) the presence of both equilibrium and rate factors as a result of the fast driving of the process. In desulphurization, for example, the flow of thin layers of slag and metal over solid coke surfaces, plus the contact between droplets of iron falling through the slag layer in the hearth, would lead one to expect a close approach to equilibrium. On the other hand, most of the critical part of sulphur removal may occur in a short time and distance below the tuyeres with perhaps an accompanying decrease in oxygen pressure and the concurrent reduction of much of the silicon and manganese, so its degree of approach to equilibrium may be quite variable. Probable Chemistry of Desulphurization Since there is little evidence that sulphur atoms in the iron solution are aasociated to any appreciable extent in molecules such as MnS, the transfer from slag to metal and back again can be written:* (FeS) ? [FeS], [I] hence the following reactions seem most probable in the slag phase, (FeS) + (CaO) ? (CaS) + (FeO), [2] and, (FeS) + (MnO) ? (MnS) + (FeO). 131

Jan 1, 1949

By B. M. Larsen, T. E. Brower

THIS discussion is based on statistical manipulation and evaluation of operating data from several commercial blast furnaces which include rather wide variations in practice. We are concerned here mainly with the effect of manganese on sulphur elimination under operating conditions in commercial blast furnaces, but this effect can be outlined more clearly by including certain other variables such as silicon in iron and slag basicity, which are all in part interrelated. Real progress in understanding all of the smelting-zone reactions in this process requires more laboratory studies of slag-metal melts similar to those in the blast furnace, with careful control of oxygen pressure. Such experimental work is very difficult, however, and in the meantime, with the present scarcity of more fundamental data, such statistical trends and correlations as can be obtained from commercial furnace operating records may help in choosing laboratory test conditions as well as adding to our knowledge of operating procedures. We do not know just why the furnace data are apparently so irregular that statistical treatment of large numbers is needed to obtain accurate trends. It is partly caused, no doubt, by the many simultaneous variables present, but there are perhaps also such factors as: (I) the con- tinual swings up and down so characteristic of the process; (2) difficulty of accurate sampling of co-existing phases, as well as (3) the presence of both equilibrium and rate factors as a result of the fast driving of the process. In desulphurization, for example, the flow of thin layers of slag and metal over solid coke surfaces, plus the contact between droplets of iron falling through the slag layer in the hearth, would lead one to expect a close approach to equilibrium. On the other hand, most of the critical part of sulphur removal may occur in a short time and distance below the tuyeres with perhaps an accompanying decrease in oxygen pressure and the concurrent reduction of much of the silicon and manganese, so its degree of approach to equilibrium may be quite variable. Probable Chemistry of Desulphurization Since there is little evidence that sulphur atoms in the iron solution are aasociated to any appreciable extent in molecules such as MnS, the transfer from slag to metal and back again can be written:* (FeS) ? [FeS], [I] hence the following reactions seem most probable in the slag phase, (FeS) + (CaO) ? (CaS) + (FeO), [2] and, (FeS) + (MnO) ? (MnS) + (FeO). 131

Jan 1, 1949

By R. E. Hook, H. J. Garrett, A. M. Adair

X-ray diffraction and metallographic techniques were employed to examine the impurity phases occurring in as-swaged and recrystallized chromium produced fvom high-purity iodide chromium crystals. Chromium oxides are found to form in a consistent manner associated with the temperature of recrystallization. Microscopically observable second phase particles of Cr203 are observed to form intergranulurly beginning at 1300T. Beginning at 1500°C. Cr30, is formed intergvanulurly, atzd at 1600°C and above Cr30, is also formed in association with migrating grain boundaries. Geometrical traces formed by particles of this high temperature oxide uithin the grains rez)eal the histmy of grain boundary motion. X-ray evidence is presented which suggests the existence of a high temperature form of Cr203. Other impurity phases in addition to the oxides of chromium are also present. THE partitioning Of impurity elements between grain boundary aid lattice sires, either as solutes in solution or as second phases, may exercise an important influence on the mechanical behavior of metals and alloy systems. This partitioning of impurities could have a direct bearing on the iecrys-

Jan 1, 1963

By C. W. Greenhalgh

THE accuracy with which grade and tonnage of a mineral deposit may be calculated from diamond-drill assays is dependent upon: (I) the reliability of core and sludge samples and (2) the validity of methods used in grade and tonnage calculations. Limitations imposed by drilling and sampling preclude elaborate methods of computation. In adjusting core and sludge assays the importance assigned the core and sludge samples may be based on either the respective weights recovered or the respective volumes represented by each. Only when core and sludge recoveries are poor do discrepancies between adjusted assays calculated by these two methods develop, in which case the "weight" method gives emphasis to the core sample and the "volume" method gives emphasis to the sludge sample. When the sludge suffers classification within the drill hole, the weight method gives more accurate results; when the sludge sample suffers no classification, the volume method gives more accurate results. Any drilling campaign offers a compromise between desired accuracy on the one hand and expediency, limited time, money, or facilities on the other. Since the determination of grade and tonnage is an approximation at best, a proper basis for their computation requires a knowledge of the limitations imposed by all phases of work upon which the calculations depend. A rational basis for coordination of these phases of work requires determination of: (I) the degree of accuracy desired, as a function of the object of examination; (2) the degree of accuracy attainable, as a function of the limitations imposed in the drilling and sampling program; and (3) the validity of method to be used in calculating grade and tonnage from core and sludge assays. This paper presents results of a comparison made between two commonly used methods of adjusting core and sludge assays, the assumptions upon which these methods are based, and the interrelationship of the phases of work upon which these calculations are dependent. OBJECT OF EXAMINATION The purpose of prospecting any mineral deposit is to secure sufficient samples from which ore grade and tonnage may be calculated. Any mine examination, preliminary or formal, has a definite purpose, although its scope may be limited or broad. The type of examination to be conducted is dependent, therefore, upon the reason for instituting the investigation; its scope and thoroughness are directly related to economic considerations. It is highly desirable, therefore, that before starting a drilling campaign a complete understanding of the extent of examination and desired degree of accuracy be determined as a means of simplifying the drilling program and unifying the relative degree of

Jan 1, 1946

By Ralph Hultgren, Bernard York, David W. Mitchell

It is a well-known fact that magnesium-alloy castings are apt to be coarse grained if the melt is not superheated several hundred degrees above the melting point before casting. (The casting temperature varies according to the shape of the mold. A typical casting temperature is perhaps 1400°F.) British practice is to heat to 900°C. (1650°F.) for 15 min., cool rapidly to casting temperature, and cast.' In Germany superheating is carried out at 850' to 900°C. (1560° to I650°F.) depending on the amount of scrap used. It is stated that further refinement will be obtained by prolonging the period of superheating or by increasing the superheat temperature to 950°C. (I740°F.).2 In the United States superheating is carried out at 1600' to 1700°F. (871' to 927°C.), perhaps even higher in some places. It is stated that superheating effects are found as low as 1500°F. (816°C.), but several hours are required.3 These commercial treatments lead to grain sizes in sand castings that may vary from 4 to 8 grains per sq. mm.! in heavy sections and from 60 to IOO in 1/2-in. sections to perhaps 380 in thin sections. It is also generally known that the refining effect of superheating is lost if the melt is held for some time at lower temperatures before casting. Aside from these very qualitative statements, there is little to be found in the literature as to the effect of temperature and time of superheat on the final grain size. Because of the uncertainty of these factors, the Office of Production Research and Development of the War Production Board placed a research contract with the University of California, supervised by the War Metallurgy Committee. This research, which was done under the "Restricted" Project NRC-550, is the basis of this paper, which has been released for publication by the O.P.R.D. The material studied was an alloy prepared from carbothermic magnesium. The temperatures required for grain refinement proved to be widely different from those used in practice, as described in the statements in the first paragraph. This difference is attributed to the fact that the magnesium in the specimens was of carbothermic origin instead of the electrolytic magnesium in common use. Materials and Methods The magnesium alloy studied was one of the most popular sand-casting alloys, with a nominal composition of 9 Per cent aluminum, 2 per cent zinc, and 0.1 per cent (minimum) manganese and the balance magnesium. This is designated

Jan 1, 1945

By Scott Turner

IT has been considered that the training of an engineer is too often vocational training; that it is a pity all engineers cannot have had a period of liberal training before taking up' pure engineering. Offhand, the so-called liberal courses should bring more ready adaptability to deal with the unexpected, to face with assurance situations which have had no parallel in one's experience, and to move without hesitation under conditions which were heretofore unknown to one, than the specialized course in mining engineering. We hear increasing talk as to the necessity of making the engineer articulate and bringing him into public life. The social implications, and responsibilities of engineering are pointed out, as of equal importance with the prodigious marvels of engineering ingenuity. You often read of this as the logical result of the in¬creasing consciousness of the engineer as to his rela¬tive position in our modern industrial civilization. , Some wag has noted that man is the noblest work of God, but that man is the only one who has said so. Perhaps engineers are the only claimants as to the necessity of their going in for public life and service; at any rate, some liberal educators' still maintain that a well-rounded general education is the better training.

Jan 1, 1930

THE decision of the lower court (United States District Court for the Southern District of New York) in the suit of the Dwight & Lloyd Sintering Co., vs. John E. Greenawalt has been affirmed by the United States Circuit Court of Appeals for the Second Circuit. In the original suit, infringement of seven patents was alleged, these covering the process of producing a sinter .out of finely pulverized metalliferous ores as practised in shallow pans operating intermittently in distinction to the Dwight 6: Lloyd continuous machine. The court found that the long delay in bringing suit precluded any recovery of profits from the defendant under the basic down-draft sintering patent, although Dwight & Lloyd are recognized as the inventors of this' contribution to the art and its .importance is acknowledged.

Jan 1, 1928

By Eugene McAuliffe

THE Coal Division undertook its most ambitious program this year at the New York meeting, with six full' sessions and a luncheon on Monday which had a record attendance and at which the newly elected officers for the Division were announced. Eugene McAuliffe, president of the Union Pacific Coal Co., Omaha, Neb., was unanimously selected as Chairman; J. B. Morrow, preparation manager of the Pittsburgh Coal Co., as Vice-Chairman; and H. E. Nold, Ohio State University, Secretary. During the past year two new and interesting activities were conducted by the Division directed at stimulating the interest of junior and student members. Reports were presented at the luncheon meeting by the chairmen of these commit¬tees. J. B. Morrow. chairman of the paper prize awards, and H. N. Eavenson reported on the work of the mining machinery manufacturers fellowship, the work on which was completed the first of the year. Several excellent papers are expected from these two groups for the next meeting of the Division to be held in Pittsburgh some time in the fall. The regular six-session program was filled from start to finish with interesting papers and much discussion, but unfortunately not enough time for the latter. The papers covered the field of prospecting, mining methods, preparation, utilization, mechanization, and safety, and all through the program we were constantly reminded of the value and need of research in the coal industry.

Jan 1, 1936

By R. P. Rothwell

AT this our first meeting I beg to call the attention of the members of our Institute to what is certainly a question of the greatest possible importance to the industries we represent; and more particularly to the welfare of the coal and iron trades : I refer to the enormous waste of coal in mining and in its preparation for market, as now practised in our anthracite coal-fields. It is a fact which many of you can certify to, that we are wasting fully one-ha f of all the coal in the veins we are now working, and there are cases, which might be mentioned where this proportion, immense as it is, has been greatly exceeded. The popular belief that our deposits of anthracite coal are "practically inexhaustible," is very far from being founded on facts. On the contrary, supposing the present rate of increase in the production to be maintained, it is probable that a maximum yield for our coal-fields would be attained in about fifteen years ; there are in fact some of our smaller basins where the principal veins are nearly exhausted and the production has already attained its maximum. There are others, again, where the depth attained-and it must be borne in mind that we commenced working at the surface outcrop-moderate though it is (scarcely ever reaching eight hundred feet), has so increased the cost of mining as to imperil the capital invested, and though it requires but little foresight to predict the time when the difficulties of mining will be very considerably increased by reason of the greater depth, greater quantity of water, fire-damp, and other fruitful sources of cost, yet, ignoring these recognized facts, we continue to waste more than one-half of the coal where it is obtained with the least danger, expense, and trouble, that is, near the surface-either above water-level or at a moderate depth below it. The inspection of almost any accurate mine map will satisfy you that, on an average, we leave fully one-third. of the coal in the ground as pillars to support the roof; in some places more than one-third thus remains, while it is very rare that less than one-quarter is left. In almost every case this coal is absolutely lost, for it will very rarely pay to reopen gangways and lay roads to it after that portion of the mine has been abandoned. Is it necessary in all cases to support the roof, and where it is, may not some artificial

Jan 1, 1873

By Jay A. Carpenter

THIS preliminary report from the Committee to Study Relations Between Students and the Institute is submitted to our member- ship for consideration and discussion before the general subject comes up for action at the Annual Meeting in February. At present, the A. I. M. E. has a dual relationship with mining students, each relationship in no may connected with the other. To the individual student the Institute offers for $2 a year a Student Associateship in the Institute which carries with it a subscription to MINING AND METAL- 'LURGY, a watch fob, and the privilege of becoming a Junior Member after graduation without payment of the -first year's dues, if one's application is accepted. To the student's college society it offers the privilege, upon application, of becoming 'an Affiliated 'Society, which brings with it no specific supervision or aid, and in turn requires no specific conditions as to membership, fees, or rules. This Affiliated Society is distinctly a school organization which Student Associateship in the Institute can he given special status or ignored, is the local .society sees fit.

Jan 1, 1934

By M. B. Hopkins

FOR years the expression "except rubber, tin, and manganese" has appeared in practically every discussion of the natural resources of the United States. Knowledge that natural rubber is not produced in the United States has now spread from the relatively few who have reason to be interested in the country's basic raw material supplies to all those who ride in automobiles, which means everybody. This "everybody" reads in the daily papers that we have a stock pile of natural rubber and that plenty of synthetic rubber is just around the corner. Statistics as to the United States' rubber requirements and sources of supply are of interest to him only to arrive at an answer to the question : "After taking care of rubber requirements for military purposes, will there be rubber for my automobile and the many other rubber articles I want?" More than 30,000 different rubber articles are manufactured in addition to the tires and tubes which use up about 70 per cent of the rubber supply.

Jan 1, 1942

THE Nominating Committee appointed at the Division meeting in October and consisting of Frank A. Herald, A. W. Peake, C. R. McCollom, Joseph Jensen, H. W. Camp, C. P. Watson, F. Julius Fohs, George Otis Smith, J. B. Umpleby, J. M. Lovejoy and A. W. Ambrose, have presented the following ticket for the year 1929: Chairman, Joseph B. Umpleby; associate chairman, A. C. Rubel; secretary-treasurer, R. Van A. Mills; vice-chairman for Economics, Warren A.. Sinshein~er; vice-chairman for Engineering Education, H. C. George; vice-chairman for Engineering Research, Harry H. Hill; vice-chairman for Production, C. P. Watson;vice-chairman for Refinery Engineering, A. D. David. For Production Engineering Charles V. Millikan. is named vicechairman, with ,Charles E. Beecher, Glenn D. Robertson and W. W. Scott as associate vice-chairmen. The Executive Committee named is to consist of Joseph B. Umpleby, chairman with A. W. Ambrose, Charles E. Beecher, A. D. David, Glenn D. Robertson, H. C. George, Harry H. Hill, John M. Lovejoy, Charles V. Millikan, R. Van A. Mills, Earl Oliver, A. W. Peake, A. C. Rubel, W. W. Scott, Warren A. Sinsheimer and .C. P. Watson, members. Ballots will be mailed to members of the Division.

Jan 1, 1928

By Robert E. Tally

CHAUNCEY L. BERRIEN, Butte, Mont. (written discussion).-Having had much actual experience with mine fires which have occurred or have been active in the mines of the Anaconda Copper Mining Co. during the past 4 years and having lately visited the fire zone of the United Verde mine with Mr. Tally, I wish to congratulate him for the success which he has had in controlling this fire and making the mine perfectly safe .for his miners. By this work he is not only keeping the property in operation but is reclaiming many lost orebodies. The ventilation system as described by him is practically the same as that used under my direction at the Mountain View mine fire in Butte in 1913 and at the Pennsylvania fire in 1916. This same system is at present being followed at the Leonard mine to extinguish a fire which has been active for 10 years although bulkheaded. The mining system in the Butte mine, at the origination of these fires was the same as that at the United Verde, namely, square setting .accompanied by the use of much timber bulkheading in the stopes owing to heavy ground. The pyritic content of the ore in Butte is not as high, but on the whole conditions have been the same, with the exception of actual location of the fire in the mine. I agree with Mr. Tally that flooding, the use of C02 or any gas, and the use of steam are all impracticable unless the fire zone can be absolutely sealed. His system of upcast escapement shafts in the fire zone, the use of bulkheads and fans to keep the gases away from the firemen, must be resorted to. By the method lie describes actual stoping may be carried on safely if started from the bottom of the fire and if the fire zone extends to the surface. In other words, the fire zone must be isolated from the rest of the mine by bulkheads and solid ground, with no ground above which can be damaged by spread of fire or caving. The serious fires in Butte have .occurred on or between levels in the mines where it was necessary to prevent their .extension upward, downward and laterally while the work of actually extinguishing them was in progress. This necessitated proper bulkheading should we lose control of the fire, the installation of ventilation similar to Mr. Tally's and the systematic drilling of holes with diamond drills for distributing water on the fire and around it.

Jan 12, 1916

By F. W. McQuiston

Idarado Mining Company's mill and surface plant are at the portal of the Treasury tunnel at elevation 10,625 ft, 12 miles south of Ouray, Colo. In 1943 and 1944 this tunnel was extended in a westerly direction to tap the Black Bear vein, and, together with the recently completed 1100-ft inclined Treasury raise, provides access to the Black Bear mine. In 1945 a 250-ton mill was placed in operation to process development ores containing much needed copper, lead and zinc for war requirements, and to serve as a pilot testing unit for larger scale milling operations. In the years 1902 to 1927 some 329,000 tons of ore were produced from mine workings on the Black Bear vein that extended downward from elevation I2,325 ft at the Black Bear tunnel portal to elevation 11,618 ft, the lowest level of the mine. The ores were taken to the Cascade and Smuggler-Union mills near Telluride over two aerial tramways. Gold bullion, a copper-lead concentrate, and a zinc concentrate were produced. Ores The Black Bear is a compound fissure vein that has undergone several stages of mineralization. The first important stage is represented by complex ores of copper. lead and zinc in a quartz gangue. Precious metal content in this stage is low. The galenn is argentiferous and varying amounts of tetrahedrite, freibergite and bornite tend to increase the normal copper content represented in chalcopyrite. The zinc occurs as a true sphalerite with little or no iron. Later re-openings of the fissure took place more or less co-extensively with the successive introduction of (I) abundant quartz gangue containing minor amounts of chalcopyrite, galena and sphalerite; (2) free gold in a fluoritic quartz gangue; and (3) barren, low-grade quartz with minor amounts of pyrite as the only important sulphide. The sulphides show practically no oxidation and little mineralogic inter-growth. Because of the common overlapping of these successive stages of mineralization within a given mining area, considerable dilution of the base-metal content takes place, thus lowering the average mill-head grade. Plant Practice Metallurgical testing was started shortly after the Black Bear vein was encountered on Treasury tunnel level in 1944. Laboratory tests showed good flotability of the minerals in the ore and indicated an economic separation could be made of the copper, lead and zinc minerals into their respective concentrates. The success of the separation is close reagent control to maintain a balance between promotion and depression of the sulphides. To maintain this balance reagent consumption for the three metal separation is considerably higher than in ordinary lead-zinc flotation.

Jan 1, 1949