Search Documents

By H. H. Vogel

THIS paper describes the milling practice and operating results of the recently installed heavy-media separation plant of Barton Mines Corporation, the world's largest producer of garnet. This pioneer application of heavy-media separation (sink-float) processes for the beneficiation of a nonmetallic ore is unique in many respects, the details of which will be apparent from the following presentation. CHARACTERISTICS OF THE ORE The property is on Gore Mountain, 5 miles west of the village of North Creek, New York, and 11 miles by road. The altitude of the mine is approximately 2800 feet. The valuable mineral, garnet, occurs in a surface deposit, the ore body being about ¾ mile long and varying in width from 50 to 300 ft. The garnet, principally almandite, Fe3A12 (Si04)3, occurs in a metamorphic rock of uncertain origin. The gangue mineral is principally hornblende, which constitutes from 40 to 80 per cent of the rock. The remainder of the gangue is divided between plagioclase feldspars and hypersthene, with smaller amounts of biotite, apatite and pyrite. The garnet content of the ore body varies from 5 to 20 per cent of the mass and averages about 10 to 12 per cent. The garnet occurs as crystals, mostly imperfectly developed, known locally as "pockets." These crystals vary in size from a fraction of an inch to a foot or more in diameter. Occasionally crystals have been found up to 30 and 36 in. in diameter but they average 4 to 6 inches. Nearly every crystal of garnet is surrounded by a rim of coarsely crystalline hornblende. The quarry faces are striking in appearance, showing crimson-red garnet crystals with their coal black rims scattered over a grayish black background. The specific gravity of the garnet is 3.8 to 4.1 while that of the hornblende ordinarily is 3.07 to 3.24. Some specimens of very dense hornblende have been found with a specific gravity as high as 3.40. The garnet crystals are laminated in structure, and readily cleave into flat, tabular pieces with sharp, chisel-like edges. Even when crushed to a very fine size, the garnet retains this flat, sharp, slivery grain shape. This characteristic, together with its hardness and toughness, gives it its value as an abrasive. FORMER OPERATIONS Mining operations have been carried on for 60 years. Until 1023, only the oxidized (soft rock) section of the ore body was mined. The oxidation, which affected the garnet only slightly, made possible the removal of the garnet from the rock by hand after it was blasted down, using small hand picks. In 1923 a mill was erected on the property, and was rebuilt and redesigned in 1928. Before the adoption of heavy-media separation, concentration was effected by

Jan 1, 1943

By Kalanadh V. S. Sastry, D. W. Fuerstenau

Design and operation of a batch balling drum that can be used easily for experimental investigation of the balling or granulation behavior of particulate materials are described briefly. An experimental procedure for ascertaining the growth kinetics of iron ore concentrates or other particulate materials with this kind of apparatus is outlined.

Jan 1, 1972

By A. Werenfels

No PETROLEUM, in commercial quantities, is found in France except the small production of the Pechelbronn field (Fig. 1) in Alsace, which produced 75,000 tons in 1923; therefore the test of the petroleum prospects of the Limagne is most interesting. Under the superintendence of M. Termier, chief engineer of the French mines, a well near Crouelle (Fig. 2) was drilled in 1921 to a depth of 856.3 m. (2808 ft.); at different depths favorable showings were encountered. The well, however, was abandoned because of drilling difficulties. A second one is now being drilled near the same place.

Jan 1, 1925

By W. H. Bassett

THE modern smelting and refining of copper is distinctly an American development. The present demand for sound and perfect castings for rolling is due to the development of American industry. Prac-tically every article made from sheet metal or, for that matter, from any form of metal is made by mass produc-tion methods. Faulty material disturbs the orderly sequence of operations and in addition requires expen-sive inspection and unbearable rejection of finished product. This demand, therefore, is positive and will have to be met. Some mines produce ore that can be smelted and re-fined without the electrolytic process into satisfactory copper for the wrought metal industry, and some of these ores carry small amounts of impurities that are of use in hardening and toughening the copper. Most of the copper ore mined contains impurities that must be removed and, fortunately, precious metals which are separated at the same time make this re-moval profitable. The modern electrolytic refineries have their methods so well under control that the product meets all re-quirements without question if properly fire refined and cast. The "if" in this case is important, because there is evidence of carelessness or want of control at times in the material from some of the producers. It is nec-essary that the melted cathodes should be saturated with oxide to dispose of sulfur and that the copper should then be poled to the proper pitch or set. Sometimes statements leak out to the effect that it is unnecessary to oxidize completely the molten cathodes and a little less rabbling saves poles, which are expensive. The re-sult is that the rolling mill gets porous castings and produces seamy or slivered sheets or strips. The condition of the molds, their temperature, and the temperature of the metal are all important to good copper cakes, wedges, or wire bars. Cracked, and burned molds leave rough places and porous spots. Molds which are out of shape, or cracked, make shrink-age cracks which gap open when the castings are hot-rolled. Dampness means porosity. Drops of oil mean porous or honey-combed areas. Poor or irregular dress-ing means mold wash in the castings. Cold copper or slow pouring means cold sets.

Jan 4, 1928

By C. B. Auel

THE subject of this paper involves the crux of the industrial safety problem. It is not overstating the fact to say that "a plant can be made as safe as the management and the workers want it to be;" if such desire is not in evidence and it is not possible to maintain interest in the work of safety, there can be practically no headway beyond the first few steps. These first steps may be said to embrace simply the mechanical or equivalent guarding of tools and equipment and may be taken in a more or less perfunctory manner; but, it has been estimated, they will not effect a reduction of more than 25 to 35 per cent. in the accidents likely to occur in an unguarded plant. The question therefore may be pertinently asked, "Whose interest is meant in the title of this paper, employers', employees?, or both?" It has been repeatedly stated that no safety work of any importance can be carried on: in a plant unless the employer believes in the value of such work. Such statements are true, but have become threadbare with constant repetition and the public is led to believe, that employers differ from ordinary human beings, that their sympathy for their fellowmen has become dulled, and they can be awakened to a sense of the fitness of things with respect to safety, health, sanitation, working hours, etc. only by legislation. There will undoubtedly be found an employer, now and again, who measures down to such specification; but the speaker, in a number of years of close contact with large employers (and his experience has been duplicated by many others) has found that the employers are usually far in advance of the general public in matters affecting the welfare of their employees, including their safety, and not from a selfish viewpoint, but from the humanitarian, economic, etc. If, at times, there is an apparent lack of headway in the solution of some problem connected with employees' welfare, it is not so much due to indifference or a failure to be awake, on the part of the employer, as it is to a lack of knowledge of the way in which to proceed to its successful accomplishment. Further, employers are, only human and cannot follow. every one of the innumerable matters connected with an industry down to their minutest details; they must delegate certain individuals as their representatives, clothing them with the necessary authority to act. These representatives should be looked upon as the Management in their respective fields and the

Jan 6, 1925

By Granville S. Borden

THE program for income tax legislation presented here proposes some diminution in the current tax burden on mineral producers but it will, if enacted, eventually increase the potential and current Government revenue from the mineral industry.

Jan 6, 1951

By John B. Myers

Vermiculite is the commercial name used to describe a micaceous mineral that expands appreciably when heated. This process, called exfoliation, results in a light weight material. The light weight material is also called vermiculite, or more exactly, expanded vermiculite. Practically all uses of vermiculite are for the expanded material. Composition and Properties Vermiculite, in its natural state, has the characteristic micaceous habit and a perfect basal cleavage and readily splits into thin laminae, which are soft, pliable, and inelastic. The monoclinic crystal faces are often marked by triangular lines at 60° and 120°. The hardness varies from 1.5 to 2 or more, depending on the composition. The specific gravity varies from 2.2 to 2.7; specific heat 0.2; fusion temperature 2,000° to 2,500°F; luster pearly to greasy; color amber, bronze, brown, dark green, and black. Feel is like talc and sometimes soapy when wet. When heated quickly at elevated temperatures, vermiculite exfoliates by expanding at right angles to the cleavage into long wormlike pieces (the name vermiculite is from the Latin vermiculari, to breed worms). This important characteristic of expansion is believed to be a mechanical separation of the layers when the contained water is converted to steam. The increase in bulk volume of commercially prepared material is 8 to 12 times, but individual flakes may expand as much as 30 times. There is no expansion parallel to the cleavage. Vermiculite may also be expanded by several chemical processes such as soaking in hydrogen peroxide, weak acids and other electrolytes. The color changes during expansion. Heat-treated material changes to a light golden bronze or cream color depending on composition. The conditions of heating affect color. Heating in an oxidizing atmosphere produces reddish colors and heating in a reducing atmosphere produces dull gray colors. The iron is generally not oxidized during chemical expansion. Vermiculite is hydrated magnesium-aluminum silicate. Although there has been much research on the chemical and structural composition, there is not yet complete agreement on the exact formula and composition. This is to be expected since vermiculite is not a mineral of fixed composition and different workers have examined different varieties. It has been proposed that vermiculite is not a single species but a family of related minerals. This has also resulted in many names for the particular vermiculite found in a certain deposit. All of this difficulty arises from the very nature of its crystal chemistry. Unlike most minerals, certain crystal structure properties and the chemical composition can be changed by the ordinary forces of nature or in the laboratory. This would suggest that vermiculite be thought of more as a variable mineral rather than a group of related species. It was stated on page 261 of this volume in the chapter on Clay Minerals by H. H. Murray of the Georgia Clay Co., that vermiculite is an equidimensional, expandable clay mineral. Gruner (ref. 14, Chap. 12) showed that the structure consists of a layer made up of two silica tetrahedral sheets with a central magnesium, iron octahedral sheet separated by two layers of water molecules and adsorbed magnesium and calcium ions. Mathieson and Walker,2a in a recent publication, agree that vermiculite must be regarded as a true clay mineral. The characteristic properties of the mineral, such as high cation ex-

Jan 1, 1960

There is mitigation for the sorrow of friends and the tragedy of sudden death when that death comes at the height of a successful career. It is not everyone's privilege to die, as has been the wish of many, in the harness—toiling, accomplishing, still necessary to the scheme of things. Nor is it everyone's privilege to leave a monument to his work. Dr. Fred Walter McNair died thus—in the midst of his work of educating, leaving along the path down the quarter century of his presidency of the Michigan College of Mines hundreds of men who, having come under his influence, have been successful in life.

Jan 1, 1924

By W. J., Kroll

MOST people believe that rare metals are always, scarce in nature, expensive to make, and therefore useless despite some miraculous properties which might make them a cure-all. There are' some metals, which are quite frequent in nature, such as zirconium, which are called rare only because our present methods for making them are elaborate, thus forcing the manufacturer to sell them at a high price. There are also truly rare metals, such as gallium, which do not occur frequently in ores, but are easily reducible from their oxides. In these cases the price of the concentration operation is the decisive factor. The distribution of the elements in the earth's crust is no indication as to the availability of a metal; the concentration operation is the critical factor. Concentration is frequently obtained in the course of metallurgical operations for the extraction of other metals, and the rare metal may be enriched in by-products, flue dusts, mother liquors or precipitates from electrolyte purification as are indium, thallium, selenium, and tellurium. A periodic table of the rare elements may serve as a basis for discussion of their properties and to establish a program. (Table 1.)

Jan 1, 1946

By Paul Billingsley

The Georgetown mining district is located in Deerlodge county, Mont., about 20 miles west of Anaconda. It lies along the divide between the headwaters of Warm Springs creek, draining eastward, and Flint creek, flowing west and north through the Philipsburg valley. The actual divide is formed by Cable mountain, a narrow ridge running north and south, terminating to the south in low hills overlooking Georgetown lake, and to the north in a high, rugged plateau that falls off to the west to the wide valley of Flint creek. On the eastern, or Warm Springs, slope of Cable mountain is the Cable mine, with the Hidden Lake mine a few miles north. On the western slope is the Southern Cross group, with smaller mines, the Twilight, Cincinnati, Red Lion, and Big Bill, at intervals to the northward. The Georgetown mines lie in the hills south of Cable mountain; the Philipsburg mines, of which the Granite Mountain, Bimetallic, Hope, and Trout are the chief, form a separate group to the north, overlooking Flint Creek valley and Philipsburg. (See Fig. 1.) The region ranges in elevation from 5,000 to 9,000 ft. It is, with the exception of the lower valleys, well timbered with small fir and pine, although Cable mountain and the higher summits to the northward rise slightly above timber line. The main valleys have the smooth contours of glaciation, and their mouths are frequently choked with morainal deposits. General Geology. In a very general way the valley of Flint creek coincides in this region with the boundary between the pre-Cambrian slates of western Montana and the folded Palaeozoic rocks of the Rocky Mountain system. The great limestone formations of the Carboniferous and Devonian, lying at flat dips, extend from Anaconda well toward the head of Warm Springs creek, but on the divide the Cambrian appears, closely folded and intruded

Jan 1, 1914

By Robert E. Brand, Strathmore R. B. Cooke

For a study of the bonding that occurs in magnetite pellets during oxidation, cubes of magnetite, hematite, and quartz were prepared, each with one surface polished and nearly optically plane. These faces were fired together under pressure and at various temperatures to determine whether bonding would occur. Sections of surfaces that bonded were examined microscopically. An attempt was made to measure the strength effected by this treatment. EARLIER work1,2 has shown that the strength developed by fired magnetite pellets containing silica or silicates is due to three separate effects. Two of these are associated with the formation of slag in the interior of each pellet at temperatures above 1000°C, where the atmosphere is substantially though temporarily neutral. The third is independent of the silica content and is responsible for the development of a hard shell around the pellet during the initial stages of firing, a condition which permits the pellet to assume the increasing load of the overlying burden and prevents extrusion of the slagged and semi-liquid interior. Pellets made from hematite concentrates do not show these effects unless specific additives are incorporated, and it is these differences in behavior which in large part account for the difficulty in producing satisfactory pellets from such concentrates. Elsewhere it has been stated that "the most important factor responsible for the development of strength in fired magnetite pellets containing no additive is the oxidation of magnetite to hematite and the subsequent recrystallization and grain growth of this constituent."' The object of the investigation reported in the present paper was to study in detail the mechanism described above and to evaluate its contribution to the strength of the fired pellet compared with other possible mechanisms, excluding slag bonding. This was effected by placing together polished faces of two cubes prepared from specific minerals and then heating them under constant pressure at different temperatures both in air and in nitrogen. The materials used were magnetite, hematite, and quartz. The magnetite was coarsely crystalline material from western Montana, the hematite was Itabira ore from Brazil, and the quartz was of optical grade but of unknown origin. A high-grade Lebanon (Pennsylvania) magnetite concentrate was used to prepare briquets for the investigation of bonding strength. Analyses of the iron oxide materials are given in Table I. The specimens for furnace treatment were prepared with a carborundum cut-off wheel, which cut the minerals into cubes approximating % in. along each edge. Care was taken to make the sides as parallel as possible. The edges of the faces to be polished were beveled, and the cubes were mounted in brass rings with sealing wax, this being essential to prevent the specimens from rocking during polishing. To prevent excessive friction, the wax was recessed so that only the brass ring and the face of each specimen would be in contact with the polishing lap. Each specimen was then ground with No. 600 carborundum to produce a level surface before polishing. The Graton-Vanderwilt process was not used for polishing because of the long time required by this method, but several other methods were tried. Cloth laps using levigated alumina or chromium oxide did not produce the desired polish. Satisfactory results were obtained by means of a pitch lap: which was used for all the mineral cubes, with levigated alumina as the polishing medium. The lap was operated in a machine similar to those used in the preparation of single optical surfaces. It was run at low speeds and moderate pressures, and polishing was stopped occasionally to prevent overheating of the lap. A good polish with flat surfaces could be obtained in about 5 min. After polishing the sealing wax was removed either in hot water or in a solvent such as turpentine.

Jan 1, 1955

By F. G. Miller, J. M. Podgursky

Laboratory and pilot plant work on tabling of 14-mesh X 0 hydrocyclone under flow are summarized. Included are: operating principles of hydrocyclones and tables; performance of these two devices, separately as well as in combination; comparison of the combination hydrocyclone-table system with other fine-coal processing systems; and application of the hydrocyclone-table system in fine-coal circuits. The data show that the table actually compensates for the shortcomings of hydrocyclone and makes a combination table-hydrocyclone system attractive, particularly in those cases where fine pyrite is one of the major contaminants.

Jan 1, 1973

By D. M. Lewis, R. C. Emmett, B. C. Wojcik, F. A. Baczek

The ElectroSlurry™ electrowinning concept has been incorporated into a process flowsheet for recovering copper from smelter flue dusts. The process has averaged 96% recovery of the copper as high-grade electrowon cathode, while at the same time removing a majority of the impurities that degrade drawn copper as a result of recycling flue dust and liberator cathodes. The dust is processed through several stages consisting of leaching, copper precipitation, ElectroSlurry electrowinning, and waste liquor treatment. The process may be integrated into a smelter operation and become an effective and feasible means of maintaining good product purity.

Jan 1, 1981

By S. J. Page

Introduction Dust from cutter machines and face drills is controlled in most mines by water. However, the large quantities of water used in metal and coal mines for dust control and suppression pose serious operational problems in water soluble ores, such as salt, trona, or gypsum. This paper reviews the strategies to suppress and collect dust on cutter machines and face drills where water usage must be restricted to very low flow rates - typically 3.78 L/min (1 gpm) or less.

Jan 1, 1985

By N. O. Johnson, J. Boyer, D. H. Sargent, R. B. Frahme

Although the Western bentonite industry has grown rapidly, it is facing major challenges to sustained growth. The fundamental penalty of costly overland transportation to both domestic markets and to US seaports is of increasing importance; as both substitute materials and foreign bentonites present more formidable competition in the historic market areas of drilling muds, foundry sands, and iron ore pelletizing; and as foreign demand grows more rapidly than domestic demand. The Western bentonite industry is facing these challenges by altering its transportation patterns, by upgrading of products, and by emphasizing customer service and stringent quality control.

Jan 1, 1980

By E. K. Soper

It has been observed that where veins or other types of orebodies are intersected by cross faults, the continuation of the ore deposit below the fault is often of lower grade than that portion above the dislocation.' In some mines, the reverse of these conditions has been noted, and the richest ore is found to occur in that portion of the vein beneath the fault intersection. Such instances seem to be less frequent than those where the richest ore is above the offset. The important and widespread influence of fault and vein intersections upon the localization of ore shoots is well known,2 but the factors that govern the position of the ore shoot relative to the fault intersection seem to be less clearly understood. The richest ore may be above or below the fault, or it may occur at the point of intersection, or there may be no change. Recent observations made by the writer in mines in Idaho and Montana suggested a possible explanation for the changes in the richness of ore below certain types of fault intersections. These observations have been supplemented by a study of the literature containing detailed descriptions of ore deposits at a large number of mines in North America. The results of these studies are presented herewith in the hope that they may lead to further discussion of this important phase of ore deposition. Relative Age oF Faults Faults which intersect veins and other ore deposits may be either pre-mineral or post-mineral in age—that is, they may be older or younger than the deposits which they intersect. Many veins are formed along

Jan 1, 1918

By J. Moore Samuel

INTRODUCTORY BEFORE the year 1909, no measurements of dust losses and flue gases had been made at the Copper Queen Reduction Works, at Douglas, Ariz. At that time the "unaccounted" loss of the smelter had reached a figure, that drew attention to the possibility of large stack losses. The measurement of dust losses had not been studied much at that time, and estimates of dust losses, with a few exceptions, were the results of tests by what has been termed "chemical methods," that is, the aspiration and filtration through cotton, wool or some similar medium of a few liters of gas, the dust being weighed on a chemical balance, and the volume of gas computed from the volume of aspirator water. The possible error of this method is enormous, and the probable error much too large for reliable results. Since the object of these tests was to discover not only the extent of the dust losses, but also the possibility of profitably reducing the same, it was decided that the method adopted must have the following characteristics: 1. The sample of gas taken for filtration must be representative of the whole volume of gas, that is to say, it must have the same dust content. This condition will be fulfilled in all cases if the gas sample is drawn off without change of rate of flow. Then it will contain the same proportion of entrained or suspended particles of dust as the original gas. In the case of flue gases which contain only fume, at a temperature above or near the sublimation point, this condition need not be adhered to since the fume will not behave as entrained particles, but more nearly as a true gas. Consequently the gas sample in this case only may be drawn off at any rate of flow. 2. The gas sample taken must be large enough (a) to yield sufficient dust to permit of accurate chemical and physical examination; (b) so that the ratio of the total volume of gas passing through the flue to the volume of gas sample taken shall not be too large.

Jan 6, 1916

By E. L. Jr. Spain

This study was undertaken primarily to determine the reasons for certain varia-tions in the soundness of gravel aggregate taken from a number of widely separated points on the Tennessee River. Under laboratory tests, concrete made with these various aggregates it some cases exhibited marked differences in specific gravity, crushing strength and durability. Gravel was studied in detail from Chattanooga to the mouth of the river and to a lesser extent from Chattanooga to Knoxville. The causes of variation were determined, and variational curves were constructed, which accurately predict the composition of aggregate at any point on the river and therefore its relative suitability for use in concrete. The aggregate at any point is suited for making sound concrete; the variance of suitability is due to varying percentages of sandstone and weathered material, which are less sound than other constituents.

Jan 1, 1937

By F. R. Hensel

Up to the present time few attempts have been made to produce hard nonmagnetic materials by heat treatment of austenitic steels. The usual result has been to cause them to pass into the martensitic stage, thus destroying to a great extent the typical austenitic properties, since this involves a transition of a portion of the iron from a face-centered to a body-centered type of atomic arrangement. High-strength nonmagnetic materials such as might be provided by properly hardening austenite are required in the electrical industry for different machine parts. In Europe nonmagnetic retainer rings for restraining the end-turns of the rotor windings in turbo-alternators have been developed as a special application of high-strength austenite. In testing1 a 28,000-kva. three-phase Siemens turbo generator running at 3000 r.p.m. at full load current, the losses in the short-circuit test were 450 kw. for the magnetic ring and 286 kw. for the nonmagnetic, and the difference should be attributable to the magnetic ring. The differences in temperatures during the same test are given in Table 1 and these show the advantage of a nonmagnetic over a magnetic retainer ring.

Jan 1, 1931

By C. H. Snyder

The paper deals with details of construction of the Colmol, including improvements in design that will be incorporated in new models. These improvements are results of problems encountered and worked out in experimental operation with the unit. Also included is a descriptive plan of operating where roof and air conditions are of the worst. A summary of production results from the machine is presented.

Jan 6, 1950