Search Documents

By James F. Kemp

In earlier gears, the custom prevailed of regarding the anthracite basins as cases of folding with slight development of faulting. Folding is so pronounced and, in the eastern and western Middle Fields, at times so violent, that the inference was a natural one and led to the widespread impression that practically all the disturbances of the seams could be explained in this way. The cross-sections and maps prepared forty or more years ago for the Second Geological Survey of P ennsylvania, by Mr. Ashburner under Prof. J. P. Lesley, exhibit little else than folds.' So far as I can discover faults fail in the charts, except in one small case in the Henry colliery near Plainsville on the outskirts of Wilkes-Barre. Some years ago, while spending a day or two in Wilkes-Barr, under the guidance of R. V. Norris, I looked over some recent and accurate cross-sections of a numbcr of the large collieries and was deeply impressed with the peculiar behavior of some of the seams and the intervening shales. Thus, a seam might present a small, more or less overturned fold, rising 30 to 50 ft. (9 to 15m.) above its general course, and yet the movement would be taken up in the overlying shales, so as hardly to be noticeable in the seams next above or below. These and similar anomalies, especially when shown with the accuracy of engineer's surveys, possess great scientific and practical interest, bearing as they do, not alone on coal mining, but on theoretical geology and the actual behavior of strata under great compressive stresses. In preparation for the semicentennial meeting of the Institute, an effort was therefore made to secure some of the most interesting sections for presentation to the members. The collection of illustrations here shown is mainly due to Douglas Bunting of the local committee, to whom and to the contributing companies acknowledgments are due. The illustrations are taken from all four of the main basins, but are chiefly from the portions nearest Wilkes-Barre. The first are in the

Jan 1, 1922

By J. R. Dolegowski, W. S. Jensen, S. M. Olafson, W. H. Champion, G. A. Kordosky

The use of pH control in solvent extraction circuits to aid in metal separation, concentration, and purification is an extremely useful technique applicable to a wide range of solutions. This paper discusses the technique in general and then gives examples of its use in extraction stages, wash and/or scrub stages, and in stripping stages, to effect the desired metal separation, concentration, and purification. Specific examples cited include Cu-Ni, Cu-Zn, and U-Mo separations using commercially available liquid ion exchange reagents.

Jan 1, 1982

By Archibald Blue

JUST one hundred years ago, in a paper read before the Royal Society of London and published in its Transactions, Rt. Hon. Charles Greville established and named the mineral species, corundum, the crystalline oxide of aluminum; and we have it on the authority of Professor Judd that in an appendix to Greville's paper the Count de Bournon correctly defined the crystallographic characters of the species. The names of its

Jan 1, 1899

Jan 1, 1928

By Rclssell Gibson, F. S. Turneaure

The tin deposit of Monserrat; Bolivia, consists of one major vein 1600 m in length. The ore is unusual because of the notable quantity of teallite, even though cassiterite is the principal tin mineral. The deposit, formed at shallow depth under a wide range in temperature, may be classed as xenothermal. Polished sections reveal a complex history of replacement, with low-temperature minerals deposited before high-temperature minerals.

Jan 1, 1950

By R. H. Olds, B. H. Sage

The transient flow of gases in long pipe lines is a problem of industrial interest. The present discussion deals with the application of the conservation of momentum and material to the transient flow of gas in conduits which are long with respect to their diameter. Solutions of the resulting equations include consideration of variations in friction and specific volume of the fluid as functions of time and position along the conduit. The changes in state along the pipe line are established as a function of time. The methods proposed may be extended to other situations. The flow of compressible fluids under steady conditions' has been considered in detail. Primary emphasis was placed on the development of simple means of taking into account the non-uniform flow' realized in long conduits under such conditions. Binder2 discussed the essential differences between the flow of compressible and uoncompressible fluids. Bonilla" proposed direct methods of solution for equations describing isothermal flow in long pipes. Similar considerations limited to steady flow have been discussed by Ruth.' Palsgrove 5 sugrested a graphical means of solving specific problems relating to the flow of gases in conduits of uniform section. Some of the basic concepts of the flow of a compressible viscous fluid in straight tubes have been described by Kuo.6 Problems of this type require knowledge of the equation of state of the fluid. In many cases it liar been convenient to assume that the fluid follows the relationship ascribed to a perfect gas. The treatment of unsteady flow of compressible fluids is less complete. This state of affairs result* from the fact that the differential equations relating pressure and flow rate with time and position for unsteady flow are nonlinear in character.' Muskat and Wyckoff presented an excellent treatment of the situation in laminar Bow where inertia forces were not of controlling importance. Somewhat earlier Hurst9 discussed the uncteady flow of fluids in petroleum reservoirs. Helhering-ton. MarRoberts. and Huntington'" established experimentally the pressure distribution and accumulative flow rate of natural gas through an unconsolidated sand. Recently Joffe11,12 conhitlcretl the specific problem of the flow of natural gas in relatively long.,. pipe lines for unsteady conditions with emphasis upon the economic feusibility of the storage of gas in such a reservoir. These discussions were based upon approximations of the partial differential equations applying to the condititons of flow. The results were descriptive of the physical situation and indirated the effertiveness of large pipe lines as cyclic storage facilities for natural gas. The advent of analog computers" has increased materially the practicality of solving nonlinear partial differential expressions. Several iterative numerical and graphical methods14,15,16 have been developed to solve nonlinear equations. However, it appears that the pair of simultaneous nonlinear partial differential equations involved in problems of this nature are not directly susceptible to solution by presently available analog computer or formal iterative numerical techniques. Nevertheless. graphical analyses afford a means of obtaining data of engineering value without special equipment. MATHEMATICAL CONSIDERATIONS Since the length of the conduit is large in comparison to the cross section in the cases to be considered, it is possible to treat the characteristics of the flow as independent of position in the cross section of the conduit. This possibility follows since the energy- connected with the velocity profile is small compared to that required to overcome the friction associated with its movement throughout the length of the line. Average values of the pressure. velocity. kinetic energy. momentum, and specific volume may he assigned to the fluid at any particular cross section. From a mathematical viewpoint this may be expressed in the following way for velocity: µ = µ(?X)..........(1) The uncertainties introduced by such assumptions usually are negligible when the ratio of length to diameter is greater than the order of 1.000. On this basis a volume element ma!. be considered to occupy the entire cross section of the conduit. Such an element is presented in Fig. 1.

Jan 1, 1951

By R. H. Olds, B. H. Sage

The transient flow of gases in long pipe lines is a problem of industrial interest. The present discussion deals with the application of the conservation of momentum and material to the transient flow of gas in conduits which are long with respect to their diameter. Solutions of the resulting equations include consideration of variations in friction and specific volume of the fluid as functions of time and position along the conduit. The changes in state along the pipe line are established as a function of time. The methods proposed may be extended to other situations. The flow of compressible fluids under steady conditions' has been considered in detail. Primary emphasis was placed on the development of simple means of taking into account the non-uniform flow' realized in long conduits under such conditions. Binder2 discussed the essential differences between the flow of compressible and uoncompressible fluids. Bonilla" proposed direct methods of solution for equations describing isothermal flow in long pipes. Similar considerations limited to steady flow have been discussed by Ruth.' Palsgrove 5 sugrested a graphical means of solving specific problems relating to the flow of gases in conduits of uniform section. Some of the basic concepts of the flow of a compressible viscous fluid in straight tubes have been described by Kuo.6 Problems of this type require knowledge of the equation of state of the fluid. In many cases it liar been convenient to assume that the fluid follows the relationship ascribed to a perfect gas. The treatment of unsteady flow of compressible fluids is less complete. This state of affairs result* from the fact that the differential equations relating pressure and flow rate with time and position for unsteady flow are nonlinear in character.' Muskat and Wyckoff presented an excellent treatment of the situation in laminar Bow where inertia forces were not of controlling importance. Somewhat earlier Hurst9 discussed the uncteady flow of fluids in petroleum reservoirs. Helhering-ton. MarRoberts. and Huntington'" established experimentally the pressure distribution and accumulative flow rate of natural gas through an unconsolidated sand. Recently Joffe11,12 conhitlcretl the specific problem of the flow of natural gas in relatively long.,. pipe lines for unsteady conditions with emphasis upon the economic feusibility of the storage of gas in such a reservoir. These discussions were based upon approximations of the partial differential equations applying to the condititons of flow. The results were descriptive of the physical situation and indirated the effertiveness of large pipe lines as cyclic storage facilities for natural gas. The advent of analog computers" has increased materially the practicality of solving nonlinear partial differential expressions. Several iterative numerical and graphical methods14,15,16 have been developed to solve nonlinear equations. However, it appears that the pair of simultaneous nonlinear partial differential equations involved in problems of this nature are not directly susceptible to solution by presently available analog computer or formal iterative numerical techniques. Nevertheless. graphical analyses afford a means of obtaining data of engineering value without special equipment. MATHEMATICAL CONSIDERATIONS Since the length of the conduit is large in comparison to the cross section in the cases to be considered, it is possible to treat the characteristics of the flow as independent of position in the cross section of the conduit. This possibility follows since the energy- connected with the velocity profile is small compared to that required to overcome the friction associated with its movement throughout the length of the line. Average values of the pressure. velocity. kinetic energy. momentum, and specific volume may he assigned to the fluid at any particular cross section. From a mathematical viewpoint this may be expressed in the following way for velocity: µ = µ(?X)..........(1) The uncertainties introduced by such assumptions usually are negligible when the ratio of length to diameter is greater than the order of 1.000. On this basis a volume element ma!. be considered to occupy the entire cross section of the conduit. Such an element is presented in Fig. 1.

Jan 1, 1951

By C. O. Brawner

Introduction The procedures used to design slopes in rock have only been developed over the past 10 years. Therefore, continued review and assessment of field experience by the publication of case studies is necessary to determine the accuracy of the theory and the application of the design techniques being used. Where failures have occurred, mine management should insist that the slides be 'back analyzed' to determine the shear strength parameters at failure. These values should be used for any pit design as they reflect site conditions more accurately than any other procedure. The previous papers have dealt with the basic concepts and factors that influence stability. To illustrate the application of these concepts in the study of practical stability problems, six ease studies have been selected for review. The examples include failure of tailings dams due to an earthquake, failure and redesign of a slope in overburden, review of failures of rock slopes, calculation of the amount of seepage into a pit and influence of the groundwater on stability, and the design of slopes for a proposed 2,500 ft. deep open pit mine. All but the first example are drawn from the authors personal experience. EXAMPLE 1 Failure of Tailings Dams Due to an Earthquake On March 28. 1965 a serious earthquake occurred in Chile with the epicenter located near the town of La Liqua, about 80 miles north of Santiago. The earthquake had a rating of 7 to 7.25 on the Richter scale. A record of the acceleration was taken at Santiago where a maximum horizontal acceleration of 0.18 g. was recorded. Many small mines are located in this region. Each of the mines provided impoundment storage for tailings with one to three dykes. As a result of the earthquake, most of the dams failed. The most serious failure involved two dams at El Cobre where more than 2,700,000 cu. yd. of tailings flowed into the valley, travelled over 7 miles in a few minutes, destroyed part of the town of El Cobre and killed more than 200 people. The Chilean government commissioned an investigation into the failures. A summary of the findings was published by Dobry and Alvare7 in 1967 (1). The location of the earthquake and the tailings dams which were investigated is shown

Jan 1, 1971

By D. V. BURR

THE ORIGINAL HUDSON RIVER TUNNEL. NOT quite forty years ago a man of uncommon character entered New York. He had several hundred thousand dollars earned by railroad building in the Nest. He was not an engineer, but he had ideas of engineering work which he was destined to prove correct.. He introduced new ways of tunneling, but his plans had only one distinguishing feature-they were simply interesting as showing how such work could be done; they added nothing to the science, have never been used since his clay, and never will be used again. Engineers of repute ridiculed his proposition ; he was an Ishmael in the profession. But if engineers looked askance at him, he certainly returned their contempt in the heartiest fashion, and had no hesitancy about expressing his views of them individually and collectively. This worked to. his disadvantage when he afterward tried to raise the means to go on with the work. He found that the opinion of engineers was respected by financiers, and that money would not flow contrary to their advice. While his conception of large constructions was distinguishingly original, much more marked was his method of demonstrating the feasibility of, his schemes. In the present clays of great undertakings it is the custom to make the other man pay for the experiments. But the man from the West had other notions of how the thing ought to be done. Having wonderful confidence in his own ability and in his perception of the task before him, he used up all his own money before seeking outside assistance. By building several hundred,, feet of tunnel he proved the correctness of his theory, and the tunnel then dug forms a part of the present tube. The result-he failed to finish the tunnel. He was blind in

Mar 1, 1908

By C. W. Carpenter, P. T. Bail, J. E. Bobek

This paper presents the results of model studies made to demonstrate the validity of applying the "basic" waterflooding scaling relationships of Rapoport1 to water-wet reservoirs composed of communicating strata of different permeability. Results demonstrate that these relationships can be validly applied, and also show the combined effect of variables on recovery. This demonstration was needed to confirm that the sizable effects of communicating strata on waterflood behavior, observed in model studies, were actually representative of field behavior. INTRODUCTION Rapoport1 Collins2 and others have presented scaling laws for modeling water-oil displacements. The validity of these laws has been experimentally demonstrated for homogeneous systems only. Recently, however, several investigators have presented the results of multilayer model studies made to determine the effects of viscous, capillary and gravitational forces on oil recovery in systems composed of communicating layers of different permeability. Dyes and Braun,3 using miscible displacements to simulate water flooding, showed that vertical communication adversely affects recovery at unfavorable viscosity ratios in the absence of capillarity. Ogandzhanyants and Egorova, 4 Gaucher and Lindley,5 and Richardson and Perkins6 modeled water-oil displacements in layered systems using immiscible fluids with capillary forces present. These investigators found more efficient behavior than in the miscible system of Dyes and Braun. However, since the scaling laws had not been verified for heterogeneous systems prior to or during these tests, it was necessary to assume that the results were representative of field behavior. This report presents the results of model studies made at Jersey Production Research Co. to find out if the waterflooding scaling relationships are valid when applied to water-oil displacements in heterogeneous reservoirs with vertical communication. Data obtained in the study show the combined effects of viscous, capillary and gravitational forces on oil-recovery behavior. The studies were performed in strongly water-wet systems where strong imbibition forces were present. For systems of different wettability, the effects of capillary imbibition would be somewhat different than those presented. APPROACH The scaling laws studied were those developed by Rapoport1 and designated by him as "basic" scaling laws. These relationships require that the model be scaled to the geometry of the prototype, and that the model and prototype be operated at the same viscosity ratio and have identical relative permeability curves, contact angles and boundary conditions. It is also necessary that the groups** be identical in the two systems, although any of the parameters making up the groups may be different. Finally, the capillary pressure of one system must be directly proportional to that of the second. Studies were conducted in two four-layer models, representing quadrants of five-spots, which were geometrically similar and which had the same glass-bead packing. The fluids used assured the same wettability in both models. Thus, the contact angles and relative permeabilities of comparative sand layers in the two models were identical and the capillary pressures were directly proportional. However, one model had a characteristic length three times that of the other. To make the scaling groups equal and to check the scaling laws, it was necessary to adjust the rate, water-viscosity level, interfacial tension and water-oil density difference to compensate for the difference in model sizes.

PRACTICAL PROBLEMS AND BASIC PRINCIPLES ranging from ore testing to cost estimation get a working over from top men in the minerals beneficiation field. The Minerals Beneficiation Division developed this symposium for presentation at the 1953 Los Angeles General Meeting to assist the many people who think that having a new plant necessitates a lot of trouble and dismay. The papers and free discussion from the floor give ways and means of approaching a new plant that will relieve the strain on the organization, if adequate attention is put on the program before work begins - that is if thought is given to the program itself, before tackling the actual mill design.

Jan 9, 1953

By Samuel D. Warriner

(Wilkes-Barre Meeting, June, 1911.) THE dealings between concentrated capital invested in the conduct of our various industries and the combinations of labor known as "trade union organizations," have produced not only in the United States, but abroad, many novel methods of negotiation between employers and wage-workers. The size and strength of these organizations have destroyed the personal elements formerly governing the dealings between employer and employee and have produced various forms of trade-agreements now in more or less successful operation. The difficulty, however, has- been to secure consent of both parties to an equitable agreement. For this purpose there have been devised various forms of arbitration, either compulsory under the shadow of governmental legislation, or voluntary by mutual agreement. But these have not been altogether successful from a technical stand-point, for the reason that a compromise has generally been necessary, and in an effort to reach an agreement, terms have been made which have been neither fair nor satisfactory to either of the contending parties. The Anthracite Board of Conciliation represents one of the few thoroughly successful courts for the settlement of trade-disputes, if not the only one which has yet been evolved. The prestige of this board rests upon its successful treatment of the labor-troubles of the anthracite region for a period of more than eight years, and upon the fact that it has been able not only to reach decisions based upon the merits of the controversies, but to enforce its decisions upon both the employees and the employers. It has never been obliged to shape its conduct to secure the consent of the contending parties, and its decisions have been strictly and, in the main, cheerfully observed. The remarkable feature of this board has been that it has

Aug 1, 1911

Jan 1, 1900

By AIME AIME

WITH a brilliance undimmed by hard times, the annual dinner on Wednesday evening, Feb. 17, was a complete success. More than 600 members, friends and ladies gathered early and filled the anterooms of the grand ballroom of the Commodore Hotel, while the president's reception was in progress, and then at the sound of the gong and with the music of the orchestra, rising above the happy din of conversation thronged to their seats at the tables. Following the "potage Ambassadeur"-probably to eliminate a very real hazard-the usual toy balloons appeared and a gay and lively scene, punctuated by multitudinous explosions, ensued, as the hundreds, of variously colored spheres bounced yon and hither until their gaseous existence was ended on the glowing end of a cigar or cigarette. On the speakers' dais sat C. E. Beecher, Chairman Petroleum Division; J. Vipond Davies, representative of A. I. M. E. on the Alfred Noble Prize Committee; Corbin T. Eddy, Alfred Noble Prize recipient; A.' S. Tuttle, Vice-president American Society of Civil Engineers; W. C. Mendenhall, Director U. S. Geological Survey; George C. Bateman, representing the Canadian Institute of Mining and Metallurgy; Paul D. Merica, Institute of Metals lecturer and Chairman James Douglas Medal Committee; Champion Herbert Mathewson, James Douglas Medalist; Robert E. Tally; retiring President; G. Temple Bridgman, toast-master; Scott Turner, incoming President; F. W. Bradley, William Lawrence Saunders Medalist; Fred Searls, Jr., Chairman William Lawrence Saunders Gold Medal Committee; Arthur Notman, President Mining and Metallurgical Society of. America; Robert J. Grant, Director U. S. Mint; Landon F. Strobel, Chairman New York Section; Howard Scott, recipient of Robert W. Hunt Prize; George. B. Waterhouse, Chairman Robert W. Hunt Prize Committee; F. M. Becket, Chairman Iron and Steel Division; Ora E. Clark, recipient of the J. E. Johnson, Jr., Award; Richard Peters, Jr., Chairman J. E. Johnson, Jr., Award Committee; E. C. Bain, Howe Lecturer; Sam Tour, Chairman Institute of Metals Division; and H. Foster Bain, Chairman. Charles F. 'Band Foundation Committee. ' Each was heartily applauded when introduced by Mr. Bridgman, as was Mrs. Tally, who also made a bow. The toastmaster made graceful reference in introducing Mr. Strobel, to the large part the latter had taken in planning the meeting.

Jan 1, 1932

By K. R. Janowski, H. Conrad

As part of a program to establish the effect of crystal imperfections on laser output, a detailed study was made of the dislocation structure of ruby crystals obtained from varioius sources. Using KHSO4 as an etchant, a detailed mapping of the dislocation structure on the (0001) and the (1150) planes was carried out. A less extensive study was made of the rhombohedral planes. The average dislocation density on the basal plane was 1.5 to 3 x 106 cm&apos;2 and on the (1120) planes -5 x 10&apos; cm-2. Howe7!er, considerable variation existed between areas on a given plane. The subboundaries in the basal plane tended to lie along [1100] type directions while those on the (1120) plane tended to lie: a) parallel to the basal plane, b) along truces of the (1101) plane, and c) along normals to the traces of the (0001) planes. The orientations suggest that mang of the dislocations lie on the (0001), (1701), and (1150) planes A Laue back-rellection nnalysis Of c-axis wander in one crystal revealed a gradual increase in misorientation from me end of the crystal to the other, with a maximum variation of 1°35&apos;. Slight etching of a mechanically polished crystal revealed mumerous polishing scratches, suggesting the existence of a plastic flow layer. It is recognized that chromium concentration, lineage, and other crystalline imperfections play a role in the efficiency of ruby lasers.&apos; Consequently, it is desirable to establish in detail the imperfection structure of ruby crystals to be used as lasers. Some exploratory work along this line had already been done by Barnes&apos; and Dils and Martin.&apos;" How- referred to as the morphological system, as described by Kronberg.4 The Miller indices given in the present paper will be based on this morphological system. In this system, the three common growth planes are the (0001), the {1120}, and the {1101}.5 Since these planes are of high stability, it is expected that they are most suitable for study by the etch-pit technique. In the present investigation, a detailed mapping of the dislocation structure was carried out for the (0001) and the (1130) planes. A less extensive study was made of the etch-pit structure on rhombohedra1 planes. An analysis of dislocations in sapphire (the ruby host) was first made by kronberg,4 who postulated that slip on the (0001) plane occurred by motion of dislocations with Burgers vector 1/3 <1150> and that these dislocations might dissociate into quarter partials. An etch-pit technique using boiling phosphoric acid was developed by Scheuplein and Gibbs6, 7 for identifying dislocations intersecting the (0001) planes and the planes near (2021) in sapphire. Al-ford and Stephens8 were able to reveal dislocations on the (0001) and {1120} planes in sapphire and ruby by etching in fused potassium bisulfate (KHS04) at 675°C. The termini of basal dislocations [(000l), <1120>] were revealed by Palmour and Kriegel9 on {1120} and {1010} by thermally etching sapphire. Bond and Harvey10 were able to decorate dislocations in sapphire by adding 1 pet by weight of ZrO2 to the Al2O3 powder used in the growth of the crystals by the Verneuil technique and then heating the grown crystals for 4 hr at 1500°C. They found, using optical transmission microscopy, that many dislocations had straight segments which were parallel to one of the six [1120] directions in the basal plane. Single dislocation lines curved smoothly from one alignment to the other, turning through angles of 60 to 120 deg. Also observed were isolated hexagonal loops, approximately 10 µ in diameter, the sides of which lay along the same directions as did the longer dislocations. MATERIAL AND ETCHING PROCEDURE The ruby specimens used in this study (all containing approximately 0.04 pet Cr) had been obtained from four different sources: Linde Co., Meller Co., Valpey Crystal Corp., and those grown at Aerospace Corp.* For the initial phase of this study, several specimens were cut from the slab shown schematically in Fig. 1 which had previously been cut from a disk boule obtained from the Linde

Jan 1, 1964

By Dale Nix

DuRing the past year approximately 400 depth pressures have been recorded in the Yates field. Of these, 315 were "shut-in depth pressures," observed for the purpose of adjusting well potentials without making open-flow tests. The "shut-in depth pressures" were distributed one to each well and determined under as nearly uniform conditions as possible. Therefore, there is a scarcity of data applicable to production problems, other than the adjusting of well potentials. A few of the data obtained have been used in an attempt to solve some of the producing problems. These applications, however, merely indicate partial solutions and their review herein is to emphasize the variety of problems to which depth-pressure data can be applied, rather than to present conclusive solutions. Very little had been accomplished in the development of instruments to determine pressures within the well bore, when it was decided to obtain such information in the Yates field. Through the combined efforts of the Yates Engineering Committee and several producing companies, three methods of determining pressures in the well bore were soon developed: (1) the "compressor" method, (2) the "volume chamber" method, (3) the "depth-pressure recorder" method. "Compressor" Method.—A small volume compressor is used to inject gas into the tubing. The rate of injection is low so that the frictional losses will be reduced to a minimum. During the test, the pressures at the top of the tubing and casing are observed on recording pressure gages. .As the compressed gas depresses the fluid in the tubing, the pressure on the casing decreases while the tubing pressure increases. The tubing pressure becomes a maximum when the fluid level reaches the bottom of the tubing; and the casing pressure usually rises quickly as the gas breaks around the bottom of the tubing. The sum of the maximum pressure recorded at the top of the tubing and the pressure exerted by the weight of the compressed gas column is equal to the depth pressure at the bottom of the tubing. The procedure can be reversed;

Jan 1, 1932

By Arthur B. Yates

Diamond drilling has advanced and expanded during the past few yean. Along with this increase there has been a marked trend to rely more and more upon drilling for the outlining of ore for reserve purposes. This is especially true underground, where men have not been available for opening up ore by crosscuts, drifts and raises. During the recent heavy call upon known ore reserves, more drilling has been done for exploration and it has become expedient to drill longer lateral holes from underground and deeper holes both from surface and from exploration headings in the mines. Furthermore, these deeper holes have to be drilled closely enough to warrant calculation of "probable" if not "proven" ore, from the results obtained therefrom. Interpretation of diamond-drill results has become more precise and reliable with the growing knowledge and understanding of the geologic structures that control the geometry of ore distribution, and this has broadened the field of usefulness of the drill. All of this has created a necessity and a demand for more accurate control of the hole as to direction, a more precise and reliable method of surveying for position, and a need for better and more complete core recovery, as well as larger cores, to provide an adequate sample. At depth the control becomes more difficult and, at the same time, more important. Control A close study of drilling in various parts of the world for a period of more than 20 years has brought to light one definite rule, practically invariable; namely, that diamond-drill holes tend to deviate into a position normal to any structure existing in the rocks, such as bedding, schistosity, gneissosity, or even parting or jointing— even if the hole is started at almost any angle other than parallel with the structure. It also appears that the better developed the structure is, the more quickly will the hole get into a position perpendicular to it. It has often been said that there is a tendency for holes to "drift" in the direction of rotation. This is obviously untrue, for in a vertical hole the measure of deviation would depend upon the azimuth chosen as zero, and there is an infinite number of choices. It has been proved. however, that in homogeneous rocks there is a tendency for the hole to corkscrew, and that the direction of the spiral is the same as the direction of rotation. This may account for the belief that holes drift in that direction. Some tests have been made using right-hand and left-hand rods, and these show that no matter what the direction of rotation the hole will swing into a position perpendicular to the structure. Methods of Control The foregoing empirical rule may be used as an indirect method of control. If the prevailing structure is known, it may be advantageous to start the hole as nearly normal to it as possible, for the

Jan 1, 1946

The San Manuel district of Arizona was first prospected prior to the Civil War, but there was little or no production until 1881. Small operators tried to develop ore bodies from time to time after that without success. Then, in 1917, a drilling program was carried out; but it did not indicate a copper content of interest. Finally, in the 1940s, the U. S. Geological Survey drilled the property and obtained indications of a mineralized area. At that time, Magma Copper and its principal owner, Newrnont Mining Corporation, drilled many deep holes through the gravels and conglomerates and in 1948 proved an ore reserve of 367 million tons of 0.785% copper sulfide ore. Underground exploration and development were started in early 1948, and in 1953 design and construction of the surface facilities commenced. By the end of 1955 plant construction was completed. The ore deposit of disseminated pyrite, chalcopyrite, chalcocite, molybdenite, silver, and gold is in quartz monzonite porphyry gangue. Mine production, which is entirely underground, is by full-gravity block-caving. Initially, ore mined at a rate of 36,000 tpd was hoisted through two identical shafts. From the 5,000 ton coarse ore bins located at the collar of each shaft, the ore was hauled by a shuttle service rail- road in 100-ton bottom-dump rail cars a distance of seven miles to the rail bin. Fragmentation from block-caving supplemented by underground grizzlies at the loading stations controlled the oversize material to give a feed size acceptable to the two 7 ft standard Syrnons crushers. During operation, however, it became evident that a large amount of secondary breaking in the grizzlies was necessary to produce a suitable feed for the standard crushers. The decision was then made to install primary gyratory crushers on the surface adjacent to the shaft site ore bins. Under each 5,000-ton coarse ore bin, an 8ft by 20 ft (2.44 m by 6. 1 m) apron feeder transfers the ore to a 13 ft 6 in. by 10 ft (4. 1 m by 3. 05 m) grizzly set at 6 in. (152 mm) and sloped at 45 degrees. About 65% of the ore passes the grizzly and thus bypasses the 42 in. by 65 in. (1.07 m by 1. 65 m) Allis -Chalmers gyratory equipped with a Hydroset mechanism and having an open side setting of 5 ½ in. (140 mm). Grizzly undersize and crushed ore drop onto a 6 ft by 30 ft (1. 83 m by 9. 14 m) variable- speed apron feeder for transfer to a 54 in. by 90 ft 5 in. (1.37 m by 27.6 m) inclined conveyor equipped with a tramp iron detector. Indication of tramp iron automatically stops the conveyor and both apron feeders. When the iron is removed from the belt by the operator,

Jan 1, 1978

By E. J. Schmitz

Coming from San Antonio, Texas, and following the Galveston, Harrisburg and San Antonio Railroad westwards, one enters soon the Cretaceous formation, which forms a belt of several hundred miles, extending westwards to the boundary of Arizona and across the Rio Grande into the State of Coahuila, Mexico. The members of this formation are very numerous and in petrographical character very diverse—from a whitish or bluish, slaty, impure limestone to a hard, beautiful blue-and-red striped, and a compact heavy-bedded,

Jan 1, 1885

By C. H. Mathewson, E. M. Thalheimer

In planning the present experiments, we have made a particular effort to secure that adjustment of working conditions which would render the forthcoming tests most serviceable by way of indicating the comparative properties of the three different commercial grades of copper used. More specifically, we have endeavored to obtain certain definite information with respect to the relative behavior under test of ordinary electrolytic copper and furnace-refined lake copper containing (a) a moderate percentage of arsenic and (b) a rather large percentage of arsenic, in addition to the usual content of silver and other impurities. These comparisons were made systematic and comprehensive by testing throughout a series of (eight) reductions running from 0 to 70 per cent. in the case of cold-rolled metal, and throughout a series of (15) temperatures running from 100&apos; C. to 1,000" C. in the case of annealed metal. In other words, a survey of properties similar to that made by Grard,&apos; in the case of electrolytic copper, was here repeated (with modifications) and extended to two other commercial varieties of copper. The great importance of copper both as a material of construction and as the base of our most important alloys (aside from steel) has led to innumerable investigations of its properties, particularly in commercial forms. Naturally, the merits of furnace-refined lake coppers us. those of the very pure electrolytic product have furnished the subject of much experimental work and animated discussion, wherein the effect of arsenic has by no means been overlooked. In the literature of the past 10 years,

Jan 1, 1917