Search Documents

By N. K. Chen, R. Maddin

Single crystals of molybdenum were extended at temperatures from 1300° to 2500°C. It was found that with increasing temperatures, the yield becomes more pronounced and the number of slip bands for equal amounts of elongation decreases. Slip at high temperatures fragments the structure. OTHER than the investigations on sodium and potassium by Andrade and Tsien,&apos; the researches of Steijn and Brick&apos; on a iron single crystals at low temperatures are about the only studies of the influence of temperature on glide of body-centered cubic single crystals. The effect of test temperature on glide has been rather widely investigated with hexagonal crystals" and less widely with face-centered cubic crystals. ~~ a result of these studies it can be said that, in general, the onset of plastic flow as measured by the initial rate of strain hardening becomes more abrupt with increasing temperature, and the value of the yield decreases with increasing temperature. Strain hardening, however, is markedly affected by changes in temperature except at very low and very high temperatures where the strain hardening rate becames constant. In the present investigation it is shown that temperature affects the glide of molybdenum single crystals in much the same manner as crystals of other classes, it., for comparable strains the number of slip bands decreases with increasing temperature; shear along the slip bands increases with increasing temperature; the yield becomes more pronounced with increasing temperature of test; and the strain hardening approaches a constant at very high temperatures. In addition, it is shown that, in agreement with the work of Tsien and Chow, Qlip occurs on (110) planes in <Ill> directions. It is further shown that slip at high temperatures fragments the structure into either irregular sized cells or bent atomic planes which are roughly aligned in crystallographic directions. Experimental Procedure Single crystals 3 mm in diameter by about 25 mm long were prepared using the technique previously described.&apos; The furnace in which the crystals were grown served as the extension apparatus for the tension tests. It consisted of a 4 in. water-cooled brass tube 20 in. long which was continuously evacuated at the bottom. Two water-cooled copper electrodes held the specimen by means of spherical collets secured in place in the electrodes by set screws. These electrodes served also to transmit power and stress to the specimen. The lower electrode was clamped to a stand, while the upper electrode was fastened to one side of a lever arm flexibly supported at the top through a slightly offset pinion. A metal bellows operating elastically was attached to the upper electrode to affect a vacuum seal and allow freedom of motion. The level of the arm was adjusted by rotating a graduated nut. Rotation of the electrode was prevented by a key fitted into a groove. After the specimen was mounted and the vacuum secured, the lever arm was adjusted so that the bellows was at its relaxed position. This insured that the total weight of the specimen, the upper electrode, and the downpull of the vacuum were balanced by the horizontal beam. Since the specimen was heated by its own resistance, expansion of the specimen proceeded freely by this arrangement. During the time of heating the specimen, the beam was maintained in a horizontal position by turning the nut at the top. By graduating the lever arm and using a known dead weight on the lever arm to supply a tensile stress, the graduated nut could be read to 0.0001 in. extension. Since

Jan 1, 1955

From the historical account of the coal industry set forth in the preceding pages the reader will have learned that coal is extremely widely spread throughout the United States, and in most places it has been easily found, that it has been remarkably easy to develop, and, where the deposits were available to streams on which it could be transported to markets, it was opened almost as soon as the country was settled. Such were the mines along the James, Susquehanna, Monongahela, Ohio, Kentucky, Cumberland and Big Muddy Rivers. In other localities where such easy means of transport were not convenient, the early production was confined to local use, or to places to which it could be hauled by wagons, but everywhere small mines were established almost as soon as the country was settled, and these increased both in number and size as the available markets grew. These early mines were nearly always opened by local people, and the industry was so far-flung that its growth attracted little or no attention excepting when a labor disturbance or a breakdown in transportation occurred. Had it been concentrated in a few places as most metal industries were, or as the petroleum industry was for many years after it started, it is probable that much better records of its progress would have been kept. When the canal era began, in the eighteen twenties, coal was at first not considered as a valuable source of freight revenue, and much surprise was expressed that the receipts of the Schuylkill Canal were very largely from coal after the first few years, as was the case of the Union Canal though not to such an extent. Even the early railroads to the coal fields did not realize the extent to which the products of mines would figure in their revenues, and it was many years before railroads were built practically solely for prospective coal traffic; indeed this did not happen until some years after the Civil War. Map 12 shows the extent of the canal system in the United States in its relation to the coal fields at the time of its maximum development. It will be seen that only the coal areas in Pennsylvania, Ohio, and to a very small extent in Indiana were able to ship by canal at all, and that only a very small portion of such fields could do so. Looking backward, it is hard to understand the great hopes entertained of canals by their pro-

Jan 1, 1942

By R. I. Jaffee, H. R. Ogden, D. J. Maykuth

IN THE past year, Jaffee and Campbell&apos; and Finlay and Snyder2 reported on the mechanical properties of titanium-base alloys, some of which were in the same ranges of composition as are covered in this paper. In this paper, evidence confirming that given by Finlay and Snyder on the effects of carbon, oxygen, and nitrogen on titanium will be presented; and, in addition, new data will be given on the effects of these elements on the flow properties and phase transformation of titanium. Materials and Preparation of Alloys The preparation and general properties of iodide titanium have been adequately described elsewhere.&apos; , As-deposited iodide titanium rod, prepared at Battelle, of Vickers hardness less than 90 was employed as the base metal in the present work. This was the same material as that used by Finlay and Snyder.2 The probable analysis reported by them for standard quality metal holds here also: N 0.005 pct, 0 0.01 pct, C 0.03 pct, Fe <0.04 pct, A1 <0.05 pct, Si <0.03 pct, and Ti 99.85 pct. Carbon was added in the form of flake graphite supplied by the Joseph Dixon Crucible Co. Oxygen was added in the form of c.p. grade TiO, powder, produced by J. T. Baker Chemical Co. Nitrogen was added in Ti3N4 powder, supplied by the Remington Arms Co. Individual ingots weighed 7 or 8 g. Carbon, oxygen, or nitrogen was added by placing the corresponding powder in a capsule made from as-deposited iodide titanium rods and melting the capsule with the balance of the charge. The charge was are-melted with a tungsten electrode on a water-cooled copper hearth under a partial vacuum of very pure argon (99.92 pct minimum). Melting was practically contamination free. Vick-ers hardness increases of less than 10 points were normal for unalloyed iodide titanium control melts. Nitrogen analyses of are-melted iodide titanium showed a nitrogen content of 0.005 pct, about the same as is present in the as-deposited rod. No tungsten pickup was found in a melt of iodide titanium analyzed for tungsten. Weight losses in melting nitrogen-free alloys were very small and varied consistently from nil to 0.015 g (0 to 0.2 pct). This permitted the use of nominal composition for these alloys. Chemical analyses made for carbon, which can be analyzed conveniently by combustion methods, justified this procedure. Where nitrogen was added, considerable splattering took place. Here it was necessary to analyze for nitrogen by the Kjeldahl method. The ingots were hot rolled at 850°C to about 0.045 in. thick. After hot rolling, the strips were descaled by mechanical grinding, and then given a cold reduction of 5 to 10 pct to insure a uniform thickness throughout the length of the specimen. The edge strips and the tensile strips were annealed in a vacuum of 1x10-4 mm Hg pressure for 3 1/2 hr at 850°C and furnace cooled. Methods of Investigation Hardness Measurements: At least five Vickers hardness measurements were taken using a 10-kg load on each sample in the following conditions: (1) top and bottom of each ingot, (2) top and bottom surface of as-rolled and annealed sheet, and (3) on cross-section of annealed sheet and all quenched specimens. Tensile Tests: Tensile tests were conducted on Baldwin-Southwark testing machines having load ranges of 600 or 2000 lb. Tests were made on 1-in. gauge-length specimens, 3 1/4-in. overall length, 1/2 in. wide, 0.040 in. thick, with a reduced section 1 1/4 in. long and 0.250 in. wide. Two SR-4, A-7 strain gauges, one mounted on each side of the specimen, were used to measure the strain over a limited range to determine the modulus of elasticity. After the modulus of elasticity readings had been taken, load vs. strain readings were taken, using only one strain gauge, at increments of 0.0001 in. until the yield points were passed and then at 0.001-in. increments to the limit of the strain-gauge indicator (0.02 in.). Strain readings above 0.02 in. per in. were taken every 0.01 in., using dividers to measure the strain between the 1-in. gauge marks until the maximum load had been reached. Crosshead speed, when using the SR-4 gauges, was 0.005 in. per min, and, when using dividers, 0.01 in. per min. Flow Curves: Flow curves were determined using the true stress-true strain data obtained during the tension test. The usefulness of this type of information has been dealt with very adequately elsewhere by L. R. Jackson,&apos; J. H. Hollomon,6 and many others. Flow curves of true stress vs. true strain could be converted to the more conventional cold-work curve of 0.2 pct offset yield strength vs. percentage of cold reduction by means of the transformation, 1/1 = 1/1-R, where R is the fraction reduction in cold working. Thus, the true strains corresponding to percentage reduction can be calculated, and the 0.2 pct offset yield strengths scaled off the — 6 curve by taking the true stresses corresponding to the values of 6 + 0.002 strain. Heat Treatment: For the transformation studies, the alloys were heat treated in a horizontal-tube furnace using a dried 99.92 pct argon atmosphere, and quenched into water. Essentially no contamination was found after several hours of heat treatment at temperatures up to 1050°C. Metallography: Specimens were prepared in the

Jan 1, 1951

By Boyd Dudley, R. H. Richards

In nearly all ore-dressing operations it is a common practice to discharge mixtures of fine ore and water through spigots; for example, from classifier pockets, from jig hutches, from settling tanks, etc. As a general rule it is desirable to regulate the composition, i.e., the ratio of water to sand, of such discharged products; and this can usually be done by varying the size of the orifice or spigot through which the material is discharged. Thus it is that problems similar to the following are frequently encountered: With a given quantity of solids per unit time, of a given specific gravity, to be discharged with water under a given head, and with a given ratio of water to solid, what must be the size of the spigot opening? If the spigot is to be open continuously, there are, aside from its form, but three factors governing the rate at which it will discharge a mixture of sand and water, namely: the head of water above the spigot; the area of the spigot opening; and the viscosity of the material to be discharged. The term viscosity, as used here, means the ratio of the volume of pure water that will flow through a given orifice under a given head in a given time to the volume of the material under consideration that will flow through the same orifice in the same time under the same conditions. While the actual viscosity of water containing sand in suspension is not increased by the presence of the sand, nevertheless the volume-rate at which such a mixture will flow through an orifice is less than that at which pure water will flow, by reason of the friction of the particles of sand against each other and against the sides of the orifice. In other words, the flow is retarded as it would be by increased viscosity; and therefore, for the purpose in view, we may speak of the viscosity of a mixture of ore grains and water as defined above. The head of water above the spigot is generally fixed by the form and design of the classifier or tank to which the spigot is attached. So, with the head known, in order to determine the size of the spigot required it is necessary to know the viscosity of the desired mixture, and the coefficient of discharge of

Jan 1, 1915

By CLARENCE WM. POY

THE most common difficulty faced by an engineer or mine operator when opening a new property in a new field is the lack of roads and of cheap transportation. This one item often swings the balance of success or failure in starting a project. In Alaska, as elsewhere, such problems are more or less serious. In the boom days around the Valdez district, as well as in other parts of this territory, freighting was accom¬plished by dog teams or horses, or even by men that were willing to put their shoulders into harness, because there were virtually no roads. More important, there was only one time when supplies could be transported, and that was when there was suffi¬cient snow on the ground following a heavy wind. Then, and only then, could one depend on the snow to support horses and sleighs, and be sure that the gulleys, streams, and crevices in the glaciers were filled with snow to avoid pitfalls. These methods were used when one had no roads, no streams in the summer to float a barge, or even a trail for a pack train. If the snow was deep and soft, trans

Jan 1, 1935

YEARS ago, when metal mining was more an adventure than a well-organized business, it was often said (with some color of truth) that unless a mine could stand bad management or mismanagement, it was not much good. Today, the natural excellencies of an ore deposit are merely a challenge to the engineers to exploit it as skillfully, as efficiently, and as profit- ably as possible. A vast amount of competent and imaginative engineering management (which includes economic analysis no less than the technologic arts of mining ore and treating it) has been required to make New Cornelia the smooth-running and successful operation that can be seen at Ajo today. New Cornelia was acquired by the Phelps Dodge Corporation when it absorbed the Calumet and Arizona Mining Company in 1931. Next to Morenci, it doubtless is the corporation&apos;s biggest asset. It in no way detracts from the achievement of Phelps Dodge engineers to say that they had an admirable ore deposit to work on. New Cornelia ore, as mined, is relatively low in grade and the deposit is by no means the largest of the Porphyries; but it has these attractive features : (1) It is peculiarly suitable for opencut mining because: (a) The overburden of waste rock lying above the ore deposit was (it has long since disappeared) almost negligible. (b) The deposit is roughly circular in horizontal section, with the horizontal dimensions four to five times as great as the maximum thickness. (Nevertheless, eventually some underground mining may be desirable.)

Jan 1, 1957

By J. J. Arps

This paper reviews the methods currently in use for estimating primary oil reserves and discusses the principles on which these methods are based. Particular emphasis is placed on how these methods change with the type of information available during the life cycle of an oil property. This paper contains various novel estimating methods and shortcuts heretofore unpublished. INTRODUCTION Estimating oil reserves is one of the most important phases of the work of a petroleum engineer since the solutions to the problems he deals with usually depend on a comparison of the estimated cost in terms of dollars, with the anticipated result in terms of barrels of oil. His recommendations to management regarding the best course of action are therefore normally based on the most favorable balance between these two. Specific engineering problems which require such a knowledge of recoverable oil reserves and a projection of future rates are: [a.] the exploitation and development of an oil reservoir; [b.] the construction of gasoline plants, pipelines and refineries; [c.] the division of ownership in unitized projects; [d.] the price to be paid in case of a sale or purchase of an oil property, and the magnitude of the loan which it will support; [e.] the proper depreciation rate for the investment in oil properties; and [f.] evaluation of the results of an exploration program. This discussion will be confined to the various methods and tools which are currently in use for estimating oil reserves to be obtained during the primary phase of an oil-producing reservoir and for a projection of the future production rates. Reserves which may be obtained by secondary recovery methods or fluid injection programs and gas and gas condensate reserves will not be discussed in this paper. Unfortunately, reliable oil reserve figures are most urgently needed during the early stages when only a minimum amount of information is available. Management&apos;s interest in the oil recovery from a property—aside from its use for accounting purposes—usually declines when the property approaches its economic limit, just at the time when the reliability of the estimates is at its best. To illustrate this general idea a chart is presented (Fig. 1) showing the three periods in the life of an imaginary oil property. Time is shown on the horizontal axis, while the cumulative production and estimated ultimate recovery are plotted vertically. No particular units are used and this schematical chart is not to scale. During the first period, before any wells are drilled on a property, any estimates will of necessity be of a very general nature, based on experience from similar pools or wells in the same area, and usually expressed in barrels per acre. This will

Jan 1, 1957

It is always the case with heavy and cheap materials that the area within which they can be economically used depends upon the cost of transportation, and in those days of poor roads and no mechanical means of haulage on them, coal could only be moved a few miles from the mine by any other means than water. The need of better means of transport to the areas west of the mountains had been urged by Washington and many other leaders, but the first turnpike over the Alleghenies only reached the Ohio River at Wheeling, W. Va. in 1818. The James River and Kanawha road reached the Ohio in 1831, that from Winchester, Va. to Parkersburg in 1838, and the road through the Cumberland Gap was completed in 1797. None of these affected the coal industry excepting indirectly by building up some of the river towns which coal could reach. The inadequacy of roads alone to carry the traffic of the rapidly growing interior communities was demonstrated only a few years after the National Pike was completed, and in the early 1820&apos;s several of the states embarked upon the construction of a canal system, which had been under discussion for some years. The Erie Canal was opened in 1825 from Lake Erie to the Hudson River through New York; Pennsylvania, Virginia and Maryland had already started similar projects designed to bring traffic to their principal cities from the interior. The Pennsylvania Canal was started from Columbia, as a railroad extended from Philadelphia to that point, and it followed the Susquehanna and Juniata Rivers to Hollidaysburg; thence to Johnstown, a distance of 36 miles, where it consisted of partly railroad and partly inclined planes, the boats being hauled up, and lowered down the planes; from Johnstown the canal followed the Conemaugh, Kiskiminitas and Allegheny Rivers to Pittsburgh, 104 miles. Boats first reached Pittsburgh by this route in 1834. The Chesapeake and Potomac Canal followed the Potomac River from a point above Alexandria above the falls, to Cumberland. This canal was chartered in the eighteenth century and a portion of it was used by traffic in 1800. It was too small to be of much use and was abandoned, and later after many legal and financial vicissitudes was completed to Cumberland, traffic from there starting late in 1850. This date, however, was long after the Baltimore and Ohio Railroad had been completed to

Jan 1, 1942

By William E. Newman

When Hugh Lee Pattinson discovered, in 1829, that the crystals formed during the slow cooling of molten lead were poorer, and the remaining liquid richer in silver, than the original lead, an important step was made in the metallurgy of this metal. Being the first process applicable to the desilverization of low-grade lead bullion, it soon found its way into all European countries having such a product to treat, thereby effecting the saving of many ounces of silver annually which previously had been thrown away. The old hand process was expensive, as viewed from the standpoint of more modern methods; the labor was great and the tonnage was small, but on the other hand the results were fairly satisfactory. This process flourished for some time after the introduction of the cheaper Parkes process in 1852 and it is still in use in a few European smelteries. Only one notable improvement was made on the original process, that of Luce and Rozan at Marseilles, France. It consisted in the application of steam for stirring and the tapping of one-third of the liquid lead, through perforated plates covering the tap holes flush with the bottom of the kettle, thus leaving two-thirds in the form of crystals in the original kettle. This modification considerably lowered the operating costs as it permitted of much larger kettles, an increased tonnage and eliminated much of the slow, hard labor of the hand process. The Luce and Rozan process has persisted in its original form to the present day. Stephen Tredinnick, English born, spent most of his years around the Luce and Rozan plants at Marseilles and elsewhere in Europe, coming later to Eureka, Nev., in 1878, to operate the Luce and Rozan plant at that point. Mr. Tredinnick was a competent Luce and Rozan operator and being devoted to the process he firmly believed that with modifications the costs could be so lowered as eventually to supplant the Parkes process. Out of many schemes he decided that this could be accomplished by placing the Luce and Rozan kettles upon hydraulic rams so that each

Jan 1, 1918

By William S. Springer

A NEW preparation plant has been put in - operation to treat coal from the recently opened Concord mine, located about 15 miles west of Birmingham, Ala., by the Tennessee Coal, Iron & Railroad Co., a U. S. Steel subsidiary. The mine produces metallurgical grade coking coal from the American seam for use as coke in the company&apos;s blast furnaces at the Fairfield and Enseley works. The capacity of the operation is 1000 tons of run-of-mine per hr, approximately half of which is delivered to the by-product coke plant at Fairfield after beneficiation to metallurgical grade. The remaining portion of the mine run is rock and refuse removed during preparation. No boiler coal or other fuels are produced by this mine. Preparation of the coal is done both under- ground and on the surface. The underground primary crushing station removes some tramp iron, and screens and crushes the oversize, most of which is rock, to protect the main slope conveyor. The surface plant consists of a crushing and screening plant, large blending bins, a two- process washing plant, a water clarification and

Jan 1, 1950

By Emory Kemler

The problem of determining the most desirable operating conditions of an oil-well pumping unit or rig front, the selection of the proper material and size of sucker rods, and the design of a pumping unit require that sucker-rod loads be known with a reasonable degree of accuracy. The segregation of rig losses, the proper selection and operation of prime mover and reduction unit, and the analysis of the operation of subsurface equipment require a knowledge of polished-rod horsepower. The investigation of such problems as the instantaneous stresses set up in a pull-rod line or backside crank installation when the well is suddenly hooked on, a study of such problems as the effect of anchoring the tubing on rod load, tubing stresses and rod horsepower, and an analysis of the effect of subsurface equipment on rod loads make it necessary to have a dynamometer that is rugged, which can follow the sudden changes in load without any lag or damping effect, which will record the load in its true position with respect to polished-rod movement, and which will give a card large enough to allow the desired effects to be measured accurately. The inadequacy of the spring or fluid-pressure type of dynamometers has been covered in detail1. The data given show that dynamometers of the spring or fluid-pressure type exert a damping action on the peak loads and the inertia and friction of their load-indicating mechanism introduces a phase lag in recording the load. A dynamometer of that type will not give the load in the correct amount and will not record it in its true position with respect to stroke or time. New Type of Dynamometer Fig. 1 shows a magnetic strain-gage type of dynamometer, to be described in this paper. The strain gage A is used for measuring the load in the polished rod, a washer B and knife edge C take care of initial misalignment and reduce bending in the compression tube of the strain gage. The complete instrument can be transported in the carrying case E.

Jan 1, 1935

A piece of arid, strip-mined land in southeastern Washington recently yielded over 22 bushels of winter wheat per acre-without irrigation. The surprising crop yield is the product of an innovative reclamation technique-one of several methods now being developed as alternatives to traditional reclamation. Conventional reclamation methods are not always successful on strip-mined acreage in the arid West. Replanting native vegetation usually requires fertilizer and irrigation-both energy-intensive commodities in arid regions. Now, promising alternatives which rely solely on rainfall for irrigation are being offered by two research teams.

Jan 12, 1978

By George B. Holderer

The relation between man-hours of labor and production may be correlated for any industry, and already it has been widely used in piecework studies. It is not in general use as yet for recording labor efficiency of an enterprise or an industry. An exception to this is the Cement Institute, which tabulates the man-hours used in each operation and thus gets the total man-hours per barrel of cement. The writer knows of one steel company that keeps a complete record of man-hours for every operation from mining the ore to finishing the product. No doubt many others find the information useful, and such a study could be of value to the mineral industries.

Jan 1, 1937

By Stuart St. Clair

EARLY in 1936, when the American Petroleum Institute issued -J "American Petroleum Industry," which was a survey of the current position of the petroleum industry, and its future outlook, and the figures for petroleum requirements .for 1950 and 1960 were widely publicized by the several oil journals, the impression was given that the petroleum- industry must be nearing maturity and would by 1950 have passed the high&apos; point of its obligations to business progress in the United States.`&apos; Let -us look at the figures which might conduce, this thought. Referring to p. 32 of the report, the total indicated crude-oil requirements in 1940 are 1,099,000,000 bbl-; for 1950, the peak, 1,109,800,000 bbl.; for 1960 a decline to 1,071,020,000 bbl. This downward trend, then established, is probably expected to continue. And this in the face of a crude production in 1935 of 993,942,000 bbl., 38,858,000 bbl.

Jan 1, 1936

By F. P. Dewey

The most serious problem that confronts the lead-smelter is the waste caused during smelting by the volatilization of both lead and silver, which are consequently lost in the form of fume. It is not difficult to collect a portion of the solid materials passing out of the

Jan 1, 1890

By Mark A. Ammon

The two most widely used methods of measuring hardness are the Brinell and the scleroscope. In the Brinell method a hardened steel ball is pressed into the steel under a definite load and the area of the resulting depression is measured. The load in kg. per sq. mm. of the area of the depression is taken as a measure of the hardness. Within certain limits the hardness number so determined is independent of the load or the size of the ball. In the scleroscope method a small weight carrying a diamond point is dropped through a glass tube upon the steel and the amount of rebound is taken as proportional to the hard-&apos; ness. In both methods the scale of hardness is an arbitrary one; however, they agree in a comparative may, that is, a steel showing 50 per cent. increase in hardness by the Brinell test mill show approximately 50 per cent. increase in hardness by the scleroscope test. Yet upon consideration of the two methods it appears that, upon a steel which has been carbonized, this should not be the case ; for the scleroscope method gives almost exclusively the surface-hardness, and the condition of the material below the surface has but a slight bearing upon the hardness number. The results given by the Brinell method should, however, be the exact opposite; for the depth of penetration &apos;of a ball pressed into the steel would be dependent to a large extent upon the condition of the material below the surface. This is particularly obvious when it is considered that the size of the ball ordinarily used in the Brinell method is 1 cm. (about 8 in.) in diameter under a load of 3,000 kg., while the diamond point of the scleroscope is in the neighborhood of 0.01 in. across, fitted in a hammer of about 0.5 oz. weight and dropping from a height of 10 inches.

Jan 1, 1913

By N. A. Gokcen, S. Fujishiro

The dissociation pressure of Cr3C2 has been measured in the range of 1908" to 2237°K by means of graphite Knudsen effusion cells. It has been found that Cr3C2 vaporizes according to the following reaction: 1/3 Cr3C2 (s or 1) = 2/3 C (graph.) + Cr (g). The equilibrizcm pressure, P, of Cr (g) is found to be log Ps=- - (21,194/T) + 6.525 over solid Cr3C2 and estimated as log P, = - (19,535/T) + 5.76 over liquid Cr3C2. CARBIDES of chromium are of great importance in alloy steels and cemented carbides. The published data on their therm odynamic properties at high temperatures, however, are meager. The heat capacity and change in entropy of Cr3C2 were determined calorimetrically by Kelley and Moore1 in the range of approximately 50" to 300°K, and by Oriani and Murphy2 from 297" to 1188°K. The standard entropy of Cr3C2at 298.15°K, obtained by Kelley.7 was later confirmed by DeSorbo.4 Equilibrium in the reaction was investigated by Boericke.5 A recent tabular summary

Jan 1, 1962

By James V. Thompson

SINCE it was introduced in 1943 to recover chromite from Oregon beach sands, the Humphreys spiral concentrator has proved successful in several fields of wet mineral beneficiation. By the end of 1957, 9390 Humphreys spirals had been manufactured. Most of these are still in service. The spiral does not offer a panacea for all mineral dressing problems. Its proper application can best be determined by test work. Spirals present a unique advantage for the metallurgist to make tests in a full-size machine rather than a miniature model, without the risk involved in scaling up results. With only 10 to 40 lb of sample, the operator of a closed circuit test unit employing a full-size Humphreys spiral can conduct preliminary tests with full-scale loadings of 0.5 to 2.5 tph. With larger samples, from 300 to 500 lb, he can run longer multi-stage tests to obtain reliable data for the next step-pilot plant design. The manufacturer of the Humphreys spiral concentrator maintains a fully equipped ore dressing laboratory and by insisting on test work prior to sales has largely prevented misapplication of the spiral.

Jan 1, 1958

By U. C. Tainton

THE world-wide continuation of low prices for zinc in 1934 has militated against any striking changes in the position of the metal. The price of zinc in London at the end of the year, about £11 5/8 per long ton, or 2.5c per pound at the existing rate of exchange, is more than 25 per cent below the average price for last year. In these circumstances probably the most significant event of the year was the putting into operation of the new electrolytic plant of the Giesches company at Magdeburg, Germany. This plant is designed to have an initial capacity of 20,000 long tons per year, and it is planned to increase this to 40,000 tons annually. This development is significant not only as indicating a continued swing of zinc metallurgy towards electrolytic methods, but also because it will make Germany virtually independent of foreign sources of zinc. This will mean that the zinc tonnage normally exported to Germany from Belgium and Poland will. become available for other markets, and it is feared may lead to lower prices unless the production of Bel-

Jan 1, 1935

At a special inaugural ceremony in Blue Hill, Maine on August 3rd, Governor John H. Reed detonated the first blast to signify the beginning of development work on a new copper-zinc mining venture that seems destined to focus increased interest in the mineral potential of that State. The property which is the first new base metal mine to be discovered in the northern Appalachians in 30 years, is owned by Black Hawk Mining Co., a subsidiary of Denison Mines Ltd. of Toronto. When it goes on-stream in 1966, it will join Ducktown, Tenn., as the only active copper producing region, east of the Mississippi River. According to official reports submitted by the Company to Robert G. Doyle, Maine&apos;s State Geologist, Black Hawk has found ore reserves totalling 4.5 million tons. Assays show 2.8 million tons of 2.0&apos;; copper and 0.4 oz. of silver per ton; 1.2 million tons of 16.75% zinc and 0.58% copper; and 0.5 million tons of 6.75% lead with 4.25 oz. of silver per toil and some zinc.

Jan 9, 1964