Search Documents

By D. H. Henley, F. F. Craig, W. W. Owens

The oil recovery performance of systems producing entirely by bottom-water encroachment has been experimentally determined in a series of scaled laboratory-model tests. The effects of well spacing, fluid mobilities, rate of production, capillary and gravity forces, well penetration and well completion techniques on the oil recovery performance have been investigated. The laboratory tests were performed using two uniform, un-consolidated sand-pack models. The models have ratios of the interwell distance to the formation thickness of 12 and 2, respectively. Tests at constant total fluid production rate were performed simulating a range of uniform reservoir characteristics and operating conditions encountered in field operations. The performance was determined by material balance and by observation of the encroachment of dyed fluids into the models. The results of the model tests agreed with those obtained mathematically when the conditions previously considered in theoretical studies were simulated, that is, when the oil and water are of equal density and no capillary forces exist. The model study of bottom-water drive indicated that certain variables can aoect the oil recovery performance to a greater degree than can be predicted by present analytical methods. In one comparison, the oil recovery at a water-oil ratio of 20 (obtained at a wide well spacing) varied as much as threefold, depending upon the system's properties and the production rate. Lesser effect of mobility ratio and no eflect of capillary forces over the range studied were observed. The test 'results also showed that the deeper the well penetration into the oil column, the greater the total water production to a producing WOR of 20. However, the ultimate sweep efficiency, and so the oil recovery to this level of WOR, did not vary significantly with well penetration. Horizontal fractures at the top of the formation did not significantly change the sweep characteristics of the reservoir models when values of radius and fracture capacity encountered in actual reservoirs were used. Impermeable pancakes at the bottom of the well moderately increased the oil recovery efficiency both at water breakthrough and at high water-oil ratios. A method is outlined by which the oil recovery performance of other uniform bottom-water drive systems can be estimated from the information obtained in these model tests. INTRODUCTION When oil is produced from a well which partially penetrates an oil zone completely underlain by water, the water rises directly beneath the well in a symmetrical cone when the system is uniform. Two different flow mechanisms can cause the water cone to form—coning and bottom-water drive. In coning, the aquifer is relatively inactive and the cone is formed beneath the well by the pressure gradients associated with the oil flow to the well. The oil can be produced by a solution-gas drive, an edge-water drive or other driving forces in the interwell area. In a bottom-water drive, the driving force for oil production comes from an upward encroachment of the underlying active aquifer. Two papers have analyzed the theoretical performance characteristics of bottom-water drive reservoirs. In the initial mathematical investigation, Muskat' established the equations which determine the pressure distribution in this type of reservoir and solved these equations for certain conditions. Specifically, it was assumed that the water and oil had equal mobilities and equal densities, there were no capillary forces, the pressure throughout the oil zone remained above the bubble-point pressure, a constant pressure existed at the initial water-oil contact and the oil was completely displaced by the encroaching water. These assumptions were used in obtaining analytical solutions. In general, Muskat found that the sweep efficiency to initial water breakthrough to the well was larger for the thicker oil zones, the closer well spacings, the lower ratios of vertical to horizontal permeabilities, the smaller the penetration of the well into the oil zone and the smaller the bore size of the well. The production history after water breakthrough was expressed as a volumetric sweep efficiency at a given producing water-oil ratio. The results indicated that cumulative oil production at producing water-oil ratios of 10 is less affected by the well spacing than is the water-free production history. Muskat studied well spacing which today would be regarded as close. The maximum value of his dimensionless well spacing (ratio of interwell distance to formation thickness) was 4.3. This would require the development of a 50-ft-thick oil sand on less than 10-acre spacing if the vertical and horizontal permeabilities were equal, with

By D. E. Thomas

Oxidation rate constants were determined for Cu-Pd and Cu-Pt alloys as a function of alloy composition and temperature. Reaction products were identified. Relationship between oxidation rate constants and diffusion constants in the reaction zones is discussed. THE mechanism of oxidation of alloys is consider--'¦ ably more complex and not so well understood as that of pure metals. The oxidation of a one-phase binary alloy of which one component is a noble metal should logically be the simplest case of alloy oxidation, for in this case one is concerned presumably only with the oxidation of the base metal and the diffusion process by which it reaches the reaction site. This had led a number of investigators to study such systems. Probably the earliest work was that of Tammann and Rienacker' on the tarnishing of Cu-Au alloys at temperatures up to 300°C. These alloys oxidize according to the logarithmic law, that is, the film thickness is proportional to the logarithm of the time. The rate of film formation was found to decrease with increasing gold content. Raub and Engel² investigated the oxidation of Au-Cu, Cu-Pd, Au-Ag-Cu, Au-Pd-Cu, and Ag-Pd-Cu alloys at 750°C in air. These alloy systems form a continuous series of solid solutions at the temperature of oxidation with the exception of those containing silver. Au-Cu alloys oxidize parabolically, the rate constant decreasing slowly with increasing gold content up to about 15 atomic pct* Au, and more rapidly thereafter. An alloy with 14 pct Cu forms only a very thin layer of CuO on the surface and probably also a subscale.† Alloys containing more than 14 pct Cu have scales consisting of CuO and subscales of Cu,O embedded in nearly pure gold. The Cu-Pd alloys obey the parabolic law except for slight deviations for alloys containing 53 and 84 pct Cu. The overall oxidation rate decreases rather smoothly with increasing palladium content. A scale consisting of a thin layer of CuO and a thick layer of Cu²O and a subscale of Cu²O embedded in nearly pure palladium was observed for alloys containing 84, 53, and 30 pct Cu. An alloy with 19 pct Cu formed only a subscale of CuO embedded in nearly pure palladium, and an 8 pct Cu alloy formed only a thin film which was presumed to be PdO. The ternary alloys considered by Raub and Engel oxidized in much the same way as did the binaries. Wagner and Grunewald³ found that Ni-Au alloys, oxidized at 900°C in oxygen, formed a scale of NiO and a subscale containing NiO and gold. The overall oxidation rate increases with increasing gold content, passes through a maximum and then decreases to zero for pure gold. The fact that gold increases the oxidation rate was attributed to "pores" in the scale. Kubaschewski' investigated the air oxidation of alloys of platinum or gold with up to 10 pct Cu or Ni at temperatures in the range 300" to 1550°C. Parabolic behavior was noted for all alloys except Au-Ni, with rates decreasing in the order Au-Cu, Au-Ni, Pt-Ni, Pt-Cu. The diffusion coefficients for the latter three systems are known, and they decrease in the same order. However, activation energies for the oxidation of these alloys do not agree with the activation energies for diffusion in the respective alloy systems. Kubaschewski and Goldbeck7 nvestigated the oxidation of Ni-Pt alloys in air at temperatures of 600"

Jan 1, 1952

By D. R. Cook, W. M. Shepard, H. T. Morris

The East Tintic district in central Utah has produced ores of gold, silver, copper, lead, and zinc valued at more than $120,000,000. All of this ore has been produced from blind ore bodies in Paleozoic sedimentary rocks that are concealed beneath hydrothermally altered volcanic rocks and cut by intrusive bodies of Eocene age. The Paleozoic rocks, which range in age from Early Cambrian to Mississippian form the core and limbs of a large, northtrending asymmetric anticline that is cut by low-angle thrust faults, high-angle transcurrent faults, mineralized fissures and faults, and normal faults that are both older and younger than the mineralized fissures. The ore bodies generally may be grouped into two classes: ( 1) massive replacement bodies that are rich in silver, lead, zinc and manganese and (2) fissure veins that are valuable primarily for their content of gold, copper, and silver. The replacement ore bodies are localized chiefly in the Middle Limestone Member of the Ophir Formation of Middle Cambrian age where it has been thrust-faulted against older or younger rocks and cut by northeast-trending mineralized fissure zones. The fissure veins primarily are productive only in the Lower Cambrian Tintic Quartzite. Extensive lowgrade deposits of lead-zinc-silver ore recently have been discovered in Devonian carbonate rocks in the Lower plate of the East Tintic thrust fault but as yet are unevaluated. The principal guides to ore include: ( 1) intersections of northeast-trending fissures and crossbreaking faults that brecciate the carbonate rocks; (2) zones of late-stage pyritic, calcitic, and sericitic alteration in the lavas; ( 3) primary geochemical anomalies in the altered rocks; and ( 4) mineral zoning patterns of the known ore bodies. The present development of the Burgin mine would seem to assure the continued productivity of the district for at least a decade.

Jan 1, 1968

Jan 1, 1941

By Howard Scott

THE GREAT advances made in mechanical engineering during recent years through the use of alloy steels, as illustrated by the development of the airplane and automobile, may be ascribed primarily to the application of nickel as an alloying element. The ternary system iron-carbon-nickel has a wide industrial application and forms, further; the fundamental basis of the even greater class of the widely used quarternary steels such as nickel-chromium, nickel-silicon, and nickel-vanadium. As is not uncommon with such cases of virile growth in an industry, the application of the alloy steel in a largely empirical manner has outstripped its scientific development so that a fertile field for metallographic research still remains. In this field, the basic nickel steels require first consideration and are the subject of the present investigation, which is offered as a preliminary to the study of the more complex alloys of industrial importance. Of the principal tools of metallography-microscopic examination, determination of -mechanical properties, and thermal analysis-the last has developed much more slowly in its application to industrial needs so that the situation often exists that heat treatment operations are based on empirically determined temperatures; that is, temperatures determined without regard to the actual transformation characteristics of the alloy. This situation is undesirable as there is no uniform standard for comparison of results. It is due, outside the usual difficulties involved in temperature measurements, to the pioneer character- of much of the published work; to the lack of definiteness of the Ac2 transformation,1 particularly in low-carbon steels; to the failure to define operating conditions completely; and to the paucity of information correlating thermal characteristics with results of heat treatment.

Jan 2, 1920

By H. Shaw

IT is now generally recognized that the gravitational method of geophysical surveying is a valuable aid in elucidating the geological structure of the subsoil and enables the practical geologist to deduce the presence of useful deposits. The particular suitability of the torsion balance to the location of large and important subterranean structures has given rise to a wide. application of this method by many of the important oil companies in their search for future supplies, and so intense have been these efforts that little has been heard of the method in other connections, with the exception of occasional references to its application in the location of hidden deposits of metallic ores, salt and lignite, and a number of accounts of its use in the elucidation of geological structures. Its success in the location of salt domes is well known, and. establishes it as one of the most important of the geophysical methods, especially for the indirect location of oil. In the British Isles, however, no large occurrence of oil is likely to be revealed, and here the practical application of the gravitational method has been restricted almost entirely to the search for ores. This type of survey possesses well marked characteristics, and presents a gravitational problem that has necessitated the development of a special and probably unusual plan of campaign, full details of which it is hoped will shortly be published. The problems and difficulties encountered in this work are of necessity fundamentally related to those met with in the search for oil by means of the torsion balance, but they also possess several special and distinctive features which undoubtedly differentiate them from the obstacles confronting the oil prospector, and which call for special consideration and treatment.

Jan 1, 1928

By G. H. LeFevre

THE Metal Sales Department, with offices in New York, is responsible for the sale of the Company's products, with the exception of gold and coal. At present the department handles the sales of lead, zinc, silver, antimonial lead, , cadmium, bismuth, arsenic trioxide, and tellurium; gold is shipped direct to the United States Mint and coal is marketed by United States Fuel Company's own sales organization. The department keeps in close touch with the metal markets and collects information on marketing conditions, which it makes available to other departments of the Company. The electrolytic lead produced at the U. S. S. Lead Refinery, Inc., is a high-uality product marketed as corroding grade under the "U. S. S.-ELECTRO" brand. It is largely sold to manufacturers of paints, pigments, lead oxides, and storage batteries.

Jan 1, 1948

By A. J. Lyon

The stability and permanence of any structural material used in aircraft are of paramount importance. The spontaneous hardening, or age-hardening, which takes place in some of the aluminum alloys under ordinary conditions of temperature and atmosphere, is accompanied by an increase in tensile strength and proportional limit and a decrease in elongation or ductility. Within the last few years the introduction of a number of strong and ductile casting alloys led to a study by the Materiel Division, Air Corps, of the permanence of the physical properties in several of these alloys. It has been found that even though some alloys have good properties directly after casting or heat treatment, they are not satisfactory for stressed parts that require a combination of strength and ductility. It has also led to the conclusion that all alloys that can be hardened by artificial aging—heating in a temperature range below 170" C. (340" F.)—will harden spontaneously if allowed to stand for a sufficient length of time. It follows that, in aircraft work where the factors of safety are limited on account of the necessity of keeping the weight of the structures as low as possible consistent with their safe operation, the properties of the alloys in the stable or final condition should be used as a basis for design rather than the properties obtained on the material directly after casting. The work of Wilm in Germany, Hanson and Gayler at the National Physical Laboratory in England, and Merica, Jeffries, and others in the United States, has shown that the spontaneous hardening is characteristic to a greater or less extent in all aluminum-base alloys in which the solubility in the solid state of the alloying constituents decreases with the temperature. It has been shown that, by heating to a temperature as near as possible to the melting point of the material and soaking at that temperature for a sufficient length of time and then quenching or cooling rapidly, a maximum amount of the soluble constituents can be retained in solution and the condition of maximum hardening effect upon aging can be obtained. Also, in ordinary sand and chill castings, without heat treatment, a sufficient amount of the alloying constituents is held in solution to cause important changes in the final physical properties.

Jan 1, 1929

By A. J. Lyon

The stability and permanence of any structural material used in aircraft are of paramount importance. The spontaneous hardening, or age-hardening, which takes place in some of the aluminum alloys under ordinary conditions of temperature and atmosphere, is accompanied by an increase in tensile strength and proportional limit and a decrease in elongation or ductility. Within the last few years the introduction of a number of strong and ductile casting alloys led to a study by the Materiel Division, Air Corps, of the permanence of the physical properties in several of these alloys. It has been found that even though some alloys have good properties directly after casting or heat treatment, they are not satisfactory for stressed parts that require a combination of strength and ductility. It has also led to the conclusion that all alloys that can be hardened by artificial aging—heating in a temperature range below 170" C. (340" F.)—will harden spontaneously if allowed to stand for a sufficient length of time. It follows that, in aircraft work where the factors of safety are limited on account of the necessity of keeping the weight of the structures as low as possible consistent with their safe operation, the properties of the alloys in the stable or final condition should be used as a basis for design rather than the properties obtained on the material directly after casting. The work of Wilm in Germany, Hanson and Gayler at the National Physical Laboratory in England, and Merica, Jeffries, and others in the United States, has shown that the spontaneous hardening is characteristic to a greater or less extent in all aluminum-base alloys in which the solubility in the solid state of the alloying constituents decreases with the temperature. It has been shown that, by heating to a temperature as near as possible to the melting point of the material and soaking at that temperature for a sufficient length of time and then quenching or cooling rapidly, a maximum amount of the soluble constituents can be retained in solution and the condition of maximum hardening effect upon aging can be obtained. Also, in ordinary sand and chill castings, without heat treatment, a sufficient amount of the alloying constituents is held in solution to cause important changes in the final physical properties.

Jan 1, 1929

By H. A. Buehler

LOCATION THE Ozark region occupies a large part of the southern half, of Missouri, the northern portion of Arkansas and comparatively small areas in northeast Oklahoma, southwest Kansas, and southern Illinois. . It is a roughly elliptical plateau which has been deeply dissected by stream erosion, and which slopes imperceptibly into the prairie regions to the north, east, and west, but which terminates rather abruptly along the Arkansas River on the south and Tertiary lowland to the southeast. The-Boston Mountains extending for a distance of some 200 miles (321 -km.) along the Arkansas River rise to an elevation of 2000 ft. (609 m.), forming the most prominent topographic feature of the region. The so-called St. Francois Mountains in St. Francois, Madison, and adjoining counties in southeast Missouri, form a prominent but more restricted topographic feature, the highest point rising to an elevation of 1800 ft. (548 m.).. The remainder of the region is largely a plateau area varying from 800 to 1500 ft. (243 to 457 m.) in elevation. STRATIGRAPHY The region is underlain chiefly by sedimentary formations, which outcrop in roughly concentric bands around a comparatively restricted area of igneous rocks in the St. Francois Mountain district. Although located geographically near the eastern edge of the Ozarks, the St. Francois Mountains have apparently suffered the greatest orogenic movement and the lowest formations of the succession are exposed in their immediate vicinity. The various sedimentary formations of the region do not show any considerable metamorphism and have suffered little change since consolidation. With the exception of a few basic intrusions in Ste. Genevieve County and a pegmatite dike in Camden County, Missouri, there is no evidence of igneous-action, since the first sedimentary beds were deposited.

Jan 10, 1917

By C. M. Nickerson

It is apparent that repressuring of the oil measures is becoming increasingly important to the oil industry, and is a matter that warrants the best efforts of the petroleum engineer charged with applying this method of operation to a producing property. Considerable attention has been directed to repressuring in various California oil fields, such as Dominguez and Seal Beach, which have served to sell the more progressive operator on this idea and also to keep him sold. The projects that have received most attention are in comparatively young fields where the fluid levels are high, the wells, perhaps, still flowing, where the wet gas production is of considerable volume, and where there is vital need of immediate conservation of gas, which otherwise would be blown to the air. The new State of California Gas Law, which prohibits the waste of gas, has served to interest the oil industry in means of conserving the gas that is now being blown to the air because of lack of markets. This vitally affects the operator in the older, well-depleted oil fields of the state, because in many cases he has a limited market for gas, on account of the flush production from the more active oil fields. While the waste of gas is relatively small in these older fields, such as the Midway-Sunset area, it now attains considerable importance, since under the new State Gas Law it must be put to some bcneficial use. Repressuring in the older fields of California has not received the attention of the petroleum engineers that is warranted by the present situation. This paper was prepared with the view of presenting the salient features connected with repressuring in the well-depleted oil measures of the older fields, and to show what results have already been obtained in these fields by injecting the unmarketable gas into the sands, particularly in the Midway-Sunset field in the San Joaquin Valley of California. Other projects in the older fields of the state offer some supporting data in this connection, such as the Shields Canyon and the Brea Canyon fields. Gas Storage and RepressuRing On account of the lack of market for a large portion of the dry gas produced in certain of the older, well-depleted oil fields of California, the

Jan 1, 1930

By Paul M. Tyler

HISTORICAL concepts of the economics of the glass-sand industry are changing rapidly. The greatly expanded demand for glass containers combined with higher freight rates on raw materials and manufactured products have induced a migration of glass factories toward densely populated centers and the creation of new standards of place value for sub- standard sand deposits. This migration has been facilitated by the construction of pipelines to bring cheaper natural gas and liquid fuel to large cities and may be further speeded by the adoption of modern mineral dressing methods to permit economical utilization of local raw materials. Our national resources of naturally high-grade 1 silica sand are abundant, but most of the best de- posits are situated so far from large centers of population that it now costs $3.00 to $5.00 a ton to carry the sand from the mine to the optimum site for a 1 factory making beverage bottles, scientific and electrical glassware, and miscellaneous blown and pressed ware for local markets. It follows that on the basis of freight savings alone it may be economical to use material from inferior deposits closer to the factory even though the f.o.b. cost of mining and treatment may be much high

Jan 1, 1950

By R. E. Mussler, F. E. Block, T. T. Campbell

An exploratovy study was made to deternzine the feasibility of preparing beryllium by the metallother-. mic reduction of beryllium oxide. The procedure involved heating a relatively nonvolatile metal reductant in contact with beryllium oxide in a vacuum. Beryllium vapors formed in the reaction were condensed as a coherent deposit on a heated surface. Reductants tested included tanthanun, yttrium, thorium, Th-Mg, and Zr- Ti alloys, and the hydrides of lanthaniir~z, yttriunz, and zirconiur?7,. Test ten7pevatures ranged from 1350'to 175O' C, and reaction times ranged frot 30 to 100 lzr. In most cases metal recoveries were lola, although yields close to 90 pct of theoretical were obtained with latzthanum, yttrium, and zirconium reductants. In most cases metal deposits were contanzinated by beryllides, /ls/cally of the Beln M or Bel3 M type. BERYLLIUM has a variety of unique properties including light weight (sp gr 1.85), low thermal neutron absorption cross section, high scattering cross section, excellent dimensional stability, high strength to weight ratio, high melting point (1285"C), high specific heat, and high thermal conductivity. Interest in beryllium as a structural material in aerospace and nuclear-reactor applications is based on these properties. In general, the potential of beryllium has been only partially realized, largely because of the brittleness of poly crystalline forms of beryllium, difficulties associated in its fabrication, and joining problems encountered in its use in structural applications. Several excellent books and monographs are available to those interested in the occurrence, extractive metallurgy, and utilization of beryllium.1"* Although an extensive amount of research on beryllium has been in progress during the past 10 years, much of the work has been concerned either with the so-called "ductility problem" or with the development of methods of fabrication and evaluation of properties of various commercial or purified grades of metal. A recent survey of the literature indicates that only limited efforts are presently being directed toward developing new methods for reducing beryllium compounds to metal. Two major commercial methods now used to produce beryllium are the magnesium reduction of beryllium fluoride and e lec trow inn ing of beryllium from fused sodium chloride-beryllium chloride salt baths. Only a limited amount of work has been done on the direct reduction of beryllium oxide. Major factors which complicate this method are the great stability of beryllium oxide and the reactive nature of beryllium metal. The stability of the oxide necessitates extremely high reduction temperatures and vacuum operation to liberate beryllium metal vapor and cause reactions of the following type to proceed: XBeO(s) +YM(s)-MYOX(s) + XBe(& As early as 1939, roll' used this reaction for the direct reduction of beryllia by zirconium and titanium, and later in 1952 ~a~el~ studied the reduction of beryl-

Jan 1, 1967

Jan 1, 1941

[ ]

Jan 1, 1938

By Jack C. Haptonstall

Abstract-Minas de San Luis, S.A. operates the old Tayoltita mine located in the Sierra Madre Occidental in Durango, Mexico. Yearly production is 55 000 kg (1.7 million troy ox) of silver and 1000 kg (31,000 troy ox) of gold from milling 165 000 t/y (181,900 stpy) obtained from fissure veins. A 4.4 km (2.75 miles) adit, to intersect the veins below existing workings, was completed in 1974. The adit and ancillary projects facilitated extensive mechanization of the mine, ramp development of it, integration of duplicate facilities and elimination of obsolete facilities. It provided a deep-level access for exploration and development of the veins, and resulted in a 25% increase in production with the same labor force. The cost of the in-house financed project was $3.4 million.

Jan 2, 1978

By K. I. Savage, L. G. Austin, S. C. Sun

The comminution environment - the physical, chemical, and solid state - was studied for silicon carbide ground wet in a laboratory vibratory mill. The relative importance of these variables on the grinding rate of producing a material 50% passing 5µ from a powder feed of 50% passing 19µ was established.

Jan 1, 1975

By Lendall P. Warriner, Blandford C. Burgess

Jasper County lies just north of the geographical center of Georgia, bounded on the west and north by the Ocmulgee River. The county seat, Monticello, is approximately 65 miles east-southeast of Atlanta and 40 miles north of Macon. It is served by the Macon-Athens branch of the Central of Georgia Railway Co. and by five paved highways converging from adjoining county seats. Farming and lumbering are the principal local occupations. About half the county is covered with pine and mixed hardwoods; a large part of the forested land is owned by the Soil Conservation Service of the Department of Agriculture in its Piedmont Land Utilization Project. The topography is one of gently rolling field and forest with occasional hills rising 100 ft or more above the creek beds. Though annual rainfall is in the neighborhood of 60 in., most of it falls in torrential downpours of short duration which tend rapidly to erode the red soil and convert the country roads to greasy tracks of red mud. History The pegmatites of Jasper County produced a small amount of mica in World War I. In World War 11, our Government's search for this strategic mineral brought to Georgia B. C. Burgess, then Southern Manager of Colonial Mica Corp., subdivision of Metals Reserve Corp., who noted on State Highway 83 the presence of pegmatitic material used as road metal. In 1944, after severing his Government connection and returning to private practice, Mr. Burgess investigated the source of the pegmatitic material noted on his previous visit and discovered that graphic granite pegmatite had been mined for the road metal. He secured mineral leases from the Soil Conservation Service and from private owners and began preliminary development work. By 1946 he had uncovered enough pegmatite to warrant an enterprise to undertake economic development of the feldspar. In March 1947, he conveyed his leases and interest to Appalachian Minerals Co., remaining with it as Vice President and General Manager. This company has carried on additional development, removing overburden by bulldozer and drilling the pegmatites uncovered. A modern and efficient feldspar grinding plant to produce 20 mesh feldspar for the glass industry was completed and placed in operation May 1, 1948. Geology GENERAL GEOLOGY OF ROCK TYPES OTHER THAN PEGMATITE Jasper County lies within the Appalachian Crystalline Complex and approximately 40 miles north of the "Fall Line," where the Upper Cretace-

Jan 1, 1950

By Fred E. Carter

AT first sight, the platinum group of metals seem of little import to we, the people," although actually the life of the common man is much influenced by them; this influence is usually indirect, hence his lack of knowledge and interest. He generally associates platinum with high-class jewelry and lets it go at that. Were 11e to go deeper, he would find that platinum metals play their part in his food supply, his clothing. his health, his transportation, his home. And the technical man is in general only slightly better informed, for he usually does not realize how necessary platinum metals are in the manufacture of the many construction materials and chemical products with which he is acquainted. Certainly, our daily lives would be profoundly affected if platinum were suddenly to become unavailable.

Jan 1, 1944

By Jesse E. Wyrick

Gases and vapors are being safely stored in caverns constructed in salt formations. The storage of gas is cost competitive with other methods of gas storage and offers many advantages. Storage can be designed for high gas recovery rates and many operating caverns allow gas recovery rates in excess of 300 million cubic feet per day. Fenix & Scisson has constructed or consulted on many of these storage projects and presents some case histories beginning with the conversion of a bedded salt cavern to gas storage in 1961. Discussion includes basic considerations for storage construction, confirmation, and operation.

Jan 1, 1985