Search Documents

By A. Madrazo

The Standing-Katz method for predicting liquid densities of reservoir fluids has been tested using experimental data of 154 bottom-hole or recombined reservoir fluid samples. New pressure- and temperature-correction curves for the Standing-Katz type correlation are presented which improve the accuracy of prediction. INTRODUCTION The present study was undertaken to investigate the known methods of determining liquid densities and to select one of them which might yield a better correlation if additional data were employed. An appropriate correlation would incorporate the following characteristics: (1) ease of handling in the computations, (2) results within engineering accuracy and (3) data easily accessible. After careful investigation of the different methods, the Standing-Katz correlation1 appeared to have these characteristics. The Standing-Katz correlation for liquid densities of hydrocarbon systems is based upon limited data. The original work, which employs apparent densities for methane and ethane, was based on data of 15 saturated crude oils in equilibrium with natural gas. Therefore, a test of the correlation using additional experimental data would serve either to validate the Standing-Katz correlation or to form a basis for corrections if such were necessary. PROCEDURE AND GRAPHICAL SOLUTION The data of 154 bottom-hole or recombined reservoir fluid samples were employed to calculate the densities at 14.7 psia and 60°F by the method described in Table 1. Volume contributions for methane and ethane were assigned from the pseudo liquid density plot (Fig. I), but volume contributions for N2, CO2 and HzS were not considered. The densities computed at reference conditions of 14.7 psia and 60°F were then elevated to their respective temperatures and pressures by the use of the correction curves proposed by Standing.' The percentage differences between the experimental values and the calculated values were determined; these samples were grouped into temperature, pressure and density ranges to determine a possible trend. It appeared that, at temperatures above 160°F, the calculated density values were consistently larger than the experimental density values; however, no obvious trend was found for the density and pressure ranges. There is a relationship between the pressure-correction and temperature-correction curves. This relationship, embodied in the temperature-correction curve, can be expressed as follows. The experimental densities of 125 samples above their bubble points were known. From these isothermal data, it was possible to determine an experimental-density difference between two pressures; and (from Fig. 2*), a calculated density difference between the same two pressures was determined. The relative effect of temperature must be considered in the calculated-density values. The effect of temperature can be determined by entering Fig. 3* at the two densities in consideration and obtaining the change in density at constant temperature. This change, or delta density, must be added

By Walter E. Duncan, Oscar F. Tangel, A. M. Gaudin, Franklin Dewey, R. A. Johnson

Xanthates have been used as collectors of sulfide minerals in the concentration of ores by flotation for over a decade, yet much remains to be done to elucidate the underlying reasons for the remarkable effectiveness of these compounds in this connection. Briefly stated, the known facts concerning the effect of these reagents on the floatability of minerals are as follows: 1. Xanthates are without effect on silicates, silica, and generally on minerals currently regarded as "gangues." 2. Xanthates in very small amount increase enormously the floatability of sulfides of copper, lead, silver, iron and mercury. 3. If zinc sulfides are first '(activated," as by treatment with a copper salt, they are readily floated by xanthates; otherwise not. 4. Elemental copper, silver and gold have their floatabilities increased by xanthates. 5. Sulfides of elements that are not typically metallic—e.g., stibnite, realgar, molybdenit—are not made to float markedly better by treatment with xanthates. 6. Oxidized minerals of lead and copper are floated if treated with large amounts of xanthates, but not so if treated with amounts of the same order of magnitude as required for sulfide flotation. Oxidized zinc minerals are not floated unless xanthates having unusually long hydrocarbon chains (e.g., eight carbon atoms or more) are used. Iron oxides and carbonate are not floated by xanthates. From a flotation standpoint the most striking feature about xanthates is the very small amount required to accomplish startling changes in the behavior of some minerals. The amounts used in practice to effect excellent concentration are frequently of the order of 0.05 lb, of agent per ton of ore; that is, of the order of one part of agent per forty thousand parts of ore. Changes in amount of agent of the order of 0.01 lb. per ton of ore (or 0.002 lb. per ton of pulp, on a 4:l basis) have marked effects on the metallurgical results obtained. Yet these changes represent a variation of but one part per million parts of pulp.

Jan 1, 1935

By Malcolm F. Hawkes, Robert F. Mehl

THE rate of isothermal transformation of austenite to pearlite depends upon the rate of nucleation, N, and the rate of growth, G, of pearlite in austenite.1.2 Values of N are given in terms of the number of nuclei forming in unit time per unit grain boundary area of unreacted austenite; values of G are given in terms of the linear rate of radial growth. Variations in the isothermal rate with temperature result from variation of -N and G with temperature. Depth of hardening of a steel depends fundamentally upon values of N and G; changes in carbon and alloy content effect changes in N and G and thus affect depth of hardening. Quantitative studies are available on N and G for the formation of pearlite in plain carbon eutectoid steels.3 Systematic studies in this field are necessary if the phenomena are to be well enough known to furnish. a proper basis for full rationalization and for theory. Accordingly, the studies are continuing, both with respect to the effect of alloying elements upon the values of N and G in the formation of pearlite, and to the values of N and G for the formation of ferrite in hypoeutectoid steels. The present paper is the first relating to the effect of alloying elements upon the values of N and G for pearlite. It offers special interest since cobalt is known to have an anomalous effect upon the rate of formation of pearlite, accelerating it, whereas all other elements retard it.' It will be shown that cobalt increases both N and G for pearlite and that this effect is inherent in the Fe-Co-C system and not dependent upon factors relating to austenite heterogeneity nor upon any recognizable adventitious factor. Inasmuch as the rate of diffusion of carbon in austenite and the interlamellar spacing of pearlite are variables related to G and possibly to N (in a manner not yet certain), measurements of the "effect of cobalt upon them are also reported here. In the course of the work, measurements were made on the effect of cobalt upon the martensite temperature and these are given. COBALT AS AN ALLOYING ELEMENT IN STEEL PROPERTIES OF COBALT Cobalt resembles iron more closely than does any other chemical element. Its atomic number is 27, hence it is the element immediately following iron in the periodic system. The two differ in atomic structure only in the fact that cobalt contains seven electrons instead of six in the third, or transition, level of the third shell. The next shell, which is the

Jan 1, 1947

By C. W. Schulties, W. J. Mallio, L. J. Petrovic, J. A. L. Campbell

Roof control comprises about 35% of direct and indirect underground mining costs. In addition, difficulties in estimating roof control costs for new areas lead to the greatest uncertainties when negotiating coal contracts. And obviously, coal cannot be mined if the roof can't be held. Accordingly, there are strong incentives to attack this problem on as many fronts as possible. One successful geological modeling technique for predicting future roof conditions was recently applied at Peabody Coal's Simco mine No. 5, located in Coshocton, Ohio. Benefits derived from it included: - A better identification of areas where poor safety conditions may be encountered. - Improved roof control cost estimates for contract negotiations. - Estimates of time-duration while mining in bad roof areas. - Labor and materials cost predictions in an existing mine. - Productivity increases through prior knowledge of areas to avoid.

Jan 10, 1975

TO WE BOARD OF DIRECTORS OF THE AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS Gentlemen:-The following report covers briefly some of the more important activities of the Institute during the year 1923. In my report for the year 1922, I drew attention to the falling off in membership of the Institute due to the depressed condition of the mining industry in several lines and the inability of many of our members to find profitable employment in mining or its associated branches. A number who were unemployed during 1922 established connections during 1923, but a still greater number have been forced to resign or drop their membership during 1923. Fortunately, the number dropped is not so great as in the previous year. The Employment Service conducted by the four Founder Societies bears witness to the trend in business. For the young men just out of college, there are plenty of opportunities at small salaries, there are plenty of opportunities for them as laborers; but for the mature members, those of experience, there are few calls. During the last eighteen months, our Employment Service has been able to place only six of our members out of every hundred engineers for whom it has found work. Another loss which this Society has suffered, but which is not felt so keenly by our sister societies, is in its foreign members. The A. I. M. E. has always had a large foreign membership, but of recent years exchange has been so heavily against many European and South American countries that a large number of members residing abroad have been compelled to relinquish their membership. Almost invariably these members express keen regret because of the necessity that confronts them, and almost invariably the writers express hope that present conditions will not last long and that they will soon be able to ask for reinstatement. Having stated the darkest side of the picture first, it may now be drawn to your attention that in spite of these losses the number of persons applying for membership was decidedly encouraging. From the quality point of view, the membership has not gone backward. The Membership Committee has declined to recommend many

Jan 1, 1925

By C. H. Li, R. J. Stokes, T. S. Liu

Poly crystalline silver chloride specimens having different micro structures were prepared by extruding monocrystals or precompressed powder at varying temperatures. Extrusion at high temperature (370°C) produced a Fully recrystallized equi-axed material which was brittle and fractured by simple cleavage below its transition temperature (60°C for notched specimens). Extrusion at low temperatures (down to -196°C) produced an extremely tough cold-worked material with grains elongated in the extrusion direction. This material fractured below its transition temperature (which varied from —20" to —200°C) by an intergranular mode. It is concluded that cold work increases the resistance to transgranular cleavage. Fracture is then de-flected to propagate intergranularly ouer surfaces making an angle with the tensile axis with a corresponding improvement in notch toughness. This deflection is greater for extruded powder than for extruded monocrystals because of the extremely elongated grain shape. PREVIOUS work1,' on the fracture properties of fully recrystallized silver chloride under notch impact conditions has indicated that the fracture behavior is rather invariant. Thus polycrystalline materials originating from a number of sources ranging from relatively pure Harshaw single crystals to commercial-purity powder and prepared by hot extrusion at 370°C all fracture by simple cleavage with a ductile-brittle transition at 60°C, see Fig. 1. This behavior is also typical for fully annealed single crystals and appears to be fundamental to silver chloride for the particular loading conditions and notch configuration adopted. One way in which this characteristic fracture behavior can be modified is by the dispersion of alumina particles in the silver chloride matrix.' Then, particularly when the alumina particles are in the shape of spheres, the duc tile-brittle transition is much less sharply defined and occurs over a range of temperature, the transition temperature is lowered considerably and the fracture mode changes from simple cleavage to a fibrous or shear mode. The reason for this change is believed to be partly due to the nucleation of cavities in the region of the dispersed alumina particles which influences the state of stress locally and the distribution of plastic constraint at the root of the notch. It is emphasized however that this is not the sole factor responsible for the increase in toughness. In extruded materials it is reasonable to expect that the resultant grain size, texture, and the residual cold work will be influenced by the presence of a dispersed phase. The present experiments were initially designed to determine the extent to which cold work influenced the fundamental ductile-brittle transition temperature and fracture mode of silver chloride. They were stimulated by the discovery that silver chloride could be extruded at temperatures as low as -25°C when commercial-purity powder was used and as low as -196°C when single crystals were used. This working temperature was far below that previously used (370°C) and it was found that such extruded material was exceedingly tough. The reasons for the enhanced toughness and its relation to the previous work on silver chloride-alumina compacts will be discussed. EXPERIMENTAL PROCEDURE Materials Used. Two forms of silver chloride were used in this study: i) silver chloride powder

Jan 1, 1964

[ ]

Jan 1, 1938

By D. Harrington

ONE of the main functions of the United States Bureau of Mines is to obtain and disseminate information that will promote safety in and around mines, and the health and safety of employees engaged in mining. Serious health and safety conditions arising out' of contamination of air in metal mines by dust, fumes from explosives and fires, and absorption of oxygen by timber and other causes, led the Bureau of Mines to cooperate with the United States Public Health Service in the study of dust occurrence and ventilation in metal mines in various parts of the country. Dr. A. J. Lanza, of the U. S. Public Health Service, and Edwin Higgins, mining engineer of the U. S. Bureau of Mines, in 1915, made a detailed study in the mines around Joplin, Mo., their reports1 are now available. In 1916, 1917, and 1918, a similar study was made in the Butte, Mont., region by Doctor Lanza and D. Harrington, mining engineer of the Bureau of Mines; the reports of this investigation will be available soon. In 1919, the study was continued in some of the Arizona mines by D. Harrington, of the Bureau of Mines, and G. E. McElroy and Dr. R. A. Koronski, of the U. S. Public Health Service, the underground work being completed in June, 1920; these reports are now being prepared for publication. In the spring of 1920, the scope of the work was extended, with D. Harrington in charge as supervising mining engineer, and short studies made in the mines of the Coeur d' Alenes in Idaho and around Oatman, Ariz. It is hoped soon to extend the work into mines of California, Nevada, Colorado, Michigan, and Minnesota, and ultimately to other states should the mining companies be willing to cooperate.

Jan 2, 1921

By Walter Mueller

Transition in the underground coal industry, begun with the passage of the Federal Coal Mine Health and Safety Act of 1969, should be completed midway in the 1972-80 period. Surprisingly, many of the far reaching effects of this act have been, for the most part, beneficial to the industry from the standpoint of health, safety and basic operating standards. Production has dwindled, but the next few years will see production declines level out. Average declines of approximately 27% have been recorded since passage of the 1969 act, with costs increasing an average of $1.50 per ton throughout the industry. Nationwide averages presently are in the range of 14 tons per man-shift, and by 1980 this may be further reduced to a 10-ton per man-shift average for the industry. But in spite of the many temporary set-backs affecting the industry, the marketing opportunities are clearly visible. Due primarily to the energy squeeze facing the U.S. over the near term, the 'underground coal operator is and will be enjoying unusual leverage in selling his product.

Jan 10, 1972

By J. W. Gwinn

The underground haulage system in the lead-silver mine of the Bunker Hill & Sullivan Co., situated at Kellogg, Idaho, is the most extensive in the Cæur d'Alene district, comprising about 35,000 ft. of tunnels, drifts, and cross-cuts where locomotive haulage is in use. The main working adit, known as the Kellogg tunnel, or No. 9 level, is approximately 10,000 ft. in length from the portal to the main working shaft and extends beyond that about 4,500 ft. in each of two directions. On this level all the ore from the Bunker Hill & Sullivan, the Sierra Nevada Consolidated, and the Caledonia Mining Co.—an average of 44,600 tons per month—is hauled to the mills, located a short distance from the portal. Electric haulage by the trolley-type locomotive is used on this level throughout. Below this level, at intervals of 200 ft. vertically, are five other working levels (Nos. 10, 11,12,13, and 14); and the total haulage distance on these, where electric locomotives are used, is approximately 16,000 ft. No. 13 level has but recently been opened up and is not working to capacity; while the main cross-cut on No. 14 has just been started, and has no need of power haulage. Of the four levels equipped with electric haulage, Nos. 11, 12, and 13 have storage-battery locomotives, and No. 10 still retains the trolley type by reason of the small and decreasing tonnage produced. Electrification - Electric power is supplied to the mine by two systems. The first, the 500-volt direct-current trolley, was installed in 1897 when the Kellogg tunnel was started, and was extended as the tunnel advanced, being used for the first trainload of ore on Nov. 17, 1902, since which time it has been in continuous service. The current for the line is transmitted on a No. 00 copper wire as far as the shaft, and on No. 0 wire throughout the remaining length of the Kellogg tunnel; and until the installation of the storage-battery locomotives it was used in practically all the cross-cuts and drifts on each level below No. 9.

Jan 1, 1915

It is interesting to note that during the period that has elapsed since the Institute's formation, wood charcoal, anthracite and bituminous coal, as well as beehive and by-product coke, have been used as blast-furnace fuels, that the reign of supremacy of each fuel was associated with specific periods, and that each successive era was marked by a production of pig iron greater in quantity than the one it followed (Fig 1). The transition of the manufacture of blast-furnace iron from charcoal to anthracite and then to beehive coke, and ultimately to by-product coke, is a reflection of the economic limitations of each fuel coupled with availability sufficient to meet the increased demands of each succeeding decade. It is a pattern that has been followed almost without exception in the history of pig iron in every country. CHARCOAL Colonial production of iron relied exclusively on wood char- coal as a fuel, and the iron industry of this count recognizes the important role played by this fuel. Charcoal iron has been available to consumers since the beginning of the organized iron industry in America in 1645, by John Winthrop at Saugus, Mass.,1 and although its greatest use antedates the formation of the Institute, it is still used to some extent. Until about 1840 nearly all of the pig iron manufactured in the United States was made with charcoal, and it continued as a principal smelting fuel until 1855.2 After that time, more pig iron was produced with other fuels, despite the fact that

Jan 1, 1948

By Edward C. Mack, Ronald G. Stovash

INTRODUCTION Ronald G. Stovash General Superintendent Consolidation Coal Company Shoemaker Mine Moundsville, West Virginia Consolidation Coal Company's Shoemaker Mine is located in West Virginia's Northern panhandle near Wheeling, adjacent to the Ohio River. Steam coal is mined from the Pittsburgh #8 seam which averages 65 in. in thickness. The 10 in. of draw rock directly above the coal is taken on advancement, but remains when longwalled. The top consists of up to 12 in. of lower quality coal, and immediately over that, up to 10 ft of multi layered shales, coal, and bone. The cover ranges from 300 to 800 ft of shales and limestone. Two longwalls operate in the mine. The first longwall started in April 1975 and is retreating its eighth panel. This wall was the first to use shield supports in the United States. The second longwall started in September 1979 and is currently retreating its first 7,000 ft panel.

Jan 1, 1981

By B. N. Whittaker, C. J. Bonsall

The paper gives an account of the factors influencing the stability of coal mining tunnels and goes on to examine various bases of support and lining design of such tunnels in relation to geological and mining conditions. The different types of coal mining tunnels are compared and comments made regarding the factors influencing their choice and basic design features. Foremost amongst design considerations is the design method and special thought has been given to the validity of different formulae as related particularly to UK Carboniferous geological conditions. Emphasis is placed on the role of the stress field in relation to tunnel stability. Shape of mining tunnel has been investigated and conclusions drawn regarding the merits of different commonly excavated geometries from a stability point of view. Detailed design aspects pertaining to determination of tunnel lining strength and resulting stability are critically examined and current design methods are compared. Data from UK mining tunnels are included as the basis for comparison of these design methods.

Jan 1, 1983

By E. R. Smith

ANALYSIS of the requirements for gun perforation equipment suitable for penetrating casing and cement showed that these points would be involved: (1) Powder charges electrically detonated under high fluid lieads and at remote distances. (2) Selective firing of sliots in sequence. (3) Sufficient velocity for the bullet to penetrate at least two strings of seamless casing and all cement beyond the strings. (4) Heat-treatment of steels to withstand great pressures and penetration. (5) Esclusiorl of fluid under extremely high hydrostatic pressure. (6) Stranded steel wire line acting as weight - suspending and current - carrying medium. (7) Firing controls operated above the surface. (8) Determining gun depth and suspended weight by means of the wire line. (9) Portability for field use.

Jan 1, 1936

By A. Arrott, G. S. Ansell

A model is proposed to account for the observed strengthening behazlior of ferrous martensites. me model is based upon the inheritance of carbon-rich regions by the martensite which were present in the FERROUS martensite is formed by a nucleation and shear mechanism when austenite is cooled, at a rate which is fast enough to suppress the formation of pearlite, below a critical temperature (Ms ). Although the mechanism of the transformation process appears to be well understood,1,2 the mechanism re- austenite prior to transformation. These carbon-rich regions strengthen the martensite in a manner analogous to the strengthening effect due to a finely dispersed second phase. sponsible for the observed high strengths exhibited by ferrous martensites is uncertain. In this paper, a model is proposed to account for the strengthening of ferrous martensite. MODEL The maximum solubility of carbon in austenite is 1.98 wt pct as compared with a maximum solubility of 0.025 wt pct in ferrite. Prior to transformation, the carbon in the austenite is nonuniformly dis-

Jan 1, 1963

By John D. Wiebmer

First, a definition of a small scale miner is in order. The US Bureau of Mines classifies him as one who produces 360 t/d (400 stpd) of ore or less. In Canada, he would be refered to as a "junior company." Mexico identifies the small scale miner as one whose gross income from operations is less than $880,000 per year. A small surface mine in India employs less than 400 people, and a small underground mine employs less than 150. Peru considers a small scale miner one who produces less than 54 000 t/y (60,000 stpy) of ore. Obviously, the term is relative. What may be a small mine in one country is a medium or large mine in another. This lack of agreement is understandable since small scale mining does not often cross national boundaries. Rather, its effects are felt at the regional and local levels within each nation. Its importance doesn't lie with any huge contribution to the GNP or balance of trade. Instead, its value is as a local employer and as a frontrunner in geologic exploration.

Jan 2, 1979

By E. R. Parker, T. H. Hazlett

An understanding of the mechanism of creep of metals requires an accurate knowledge of shape of the time-deformation curve. An expression is developed which accurately expresses the creep curve for a number of structurally stable metals and alloys. VAST strides have been made in the development of high temperature creep resistant alloys; however, no sound understanding of the physical mechanism of creep exists to date. Consequently, creep resistant alloys are still developed by "cut and try" methods formerly so successful but now yielding returns at a continuously diminishing rate. It is apparent to all workers in the field that if the mechanism of creep were understood, much fruitless labor could be avoided. The dirth of fundamental knowledge has not discouraged the theorists. Speculation has flourished and numerous theories of creep have been proposed. A critical review of these theories reveals that, even though there are some general areas of agreement between the majority of the workers, there are many basic questions yet to be resolved.' It is generally conceded that theoretical speculation is far in advance of experimental evidence. The shortage of reliable creep data greatly hinders more rapid progress in this field. It is essential that the effects of different stresses and temperatures on the creep characteristics of metals be quantitatively determined. Once this has been accomplished, it will then be possible to evaluate the effects of alloying additions and, it is hoped, to provide a firm basis of facts for theoretical treatment of the creep phenomenon. The work reported herein was undertaken to determine the effects of such variables as stress, temperature, alloying, and structure on the creep characteristics of some metals. Material and Equipment Nickel was selected as the base material for the current investigation and an experimental program was initiated to determine the effects of temperature and stress on the creep characteristics of this material. Since a large quantity of high purity nickel was required for the proposed program and such material was not commercially available, it was decided to refine, cast, and prepare the required metal in our own laboratory. The resulting nickel test bars had the following composition, given in percentage by weight: Fe, 0.030 (1); Si, 0.003 (2); Ca, 0.001 (1); Mg, 0.020 (2); and S, 0.002 (2); to make total impurities of 0.056. The nickel (balance by difference) is 99.944 pct. The details of the purification process are described elsewhere.' This

Jan 1, 1954

By J. W. Spretnak, G. W. Cunningham

A study has been made of the growth and disappearance of voids in the interface of pressure bonded copper. The formation of visible voids is primarily due to spheroidization and coalesence of microvoids produced during the application of pressure. The microvoids could be prevented from forming by the application of high pressures or by increasing the ductility of the copper. Migrating grain boundaries were found to be more effective in void removal, than stationary grain boundaries. DURING the course of an investigation on the mechanism of pressure bonding, it was found that voids formed in the bonding interface which inhibited migration of the interfacial boundary and grain boundaries in the bond region. Therefore, an effort was made to determine the nature of the voids and how they form, grow, and disappear. This paper reports the results of such an investigation. The existence of interfacial voids is not solely a characteristic of massive components of metal which have been bonded by the application of heat and pressure, but is a phenomenon which has been observed in sintering as well. Simonsen attempted to study the sintering process by hot-stage microscopy and thereupon observed the formation of interparticle porosity as sintering proceeded. It was assumed that the porosity was due to grooves created at the location where grain boundaries joined the surface of the particle. Pranatis, Castelman, and seigle2 have also observed voids along the areas of contact in wound-wire specimens used for sintering studies. They did not discuss the point in detail since this behavior was not general, but they did suggest that the voids might develop as a result of stresses along the interparticle contact area. In previous investigations on pressure bonding, workers3 have suggested that voids may exist in the region where mating surfaces are placed in intimate contact, but the existence of the voids was not verified and no attempt was made to study the growth and disappearance of these voids. Durst noted the existence of pores in roll-clad structures prepared by cold reducing two sheets to force them in contact and then annealing to improve the bond. Since his unbonded regions contained a gas which he assumed to be insoluble, he proposed a mechanism which consisted of spheroidization of the unbonded regions and a growth of the contact area, but no speculations were made regarding disappearance of the gas filled pores. One interesting comment made by Durst was the suggestion that flattened voids with sharp corners which are produced during roll bonding will have a greater driving force for spheroidization than the more rounded pores created by pressing metal powders and thus spheroidization and neck growth will occur at lower temperatures. In this study it was necessary to demonstrate conclusively that voids can actually exist in the interfacial bond area. Experimental work was then directed toward a study of the mechanism whereby the voids grow and subsequently disappear.

Jan 1, 1963

By C. S. Barrett

It has been observed that deformation in iron takes place by slip on (110) + {112) + (123) planesl, 2, but in silicon ferrite with low deformation temperatures or high silicon contents (exceeding 4 per cent) the authors have found that slip is confined wholly to (110) planes, at least with small amounts of deformation. The purpose of the present investigation was to determine the effect of this alteration of slip mechanism on preferred orientations in cold-rolled and recrystallized strips. Incidental observations on the effect of the recrystallization temperature were also made. The numerous determinations of the texture of cold-rolled iron and steel have been in satisfactory agreement as to the principal features of the texture (with the exception of a few conclusions that apparently have been based on insufficient data). The texture is chiefly one in which 11101 directions of the grains lie along the direction of rolling, with a deviation of a few degrees, and in which the (100) planes lie in the plane of the rolled sheet, with a deviation from this position chiefly about the rolling direction as an axis. This deviation about the rolling direction as an axis has been measured by different observers and lies between about 45" and 50" or 60" for iron5, 6, 9 and is usually in the neighborhood of 50" for mild stee16, 7, 8. The range of this deviation is a function of the percentage of total reduction8, 10. Post8 reported that it decreases with increasing percentage reduction, but apparently he studied only the surface material, which Gensamer and Meh17 found to be somewhat differently oriented from the material in the inside of the sheet. McLachlan and Davey10 found that the deviation also decreases with increasing percentage of total reduction for the material in the interior of the sheet and is independent of the percentage of reduction per pass. The deviation about the cross direction as an axis (the direction in the

Jan 1, 1937

By Michael Poole, Joseph M. Chelini

Most earthmoving operations using off-road, rubber tired production equipment have abnormally high total tire costs. Achieving informational control over 7 direct and 2 indirect tire cost centers can reduce tire costs more than 50 percent; a 20 percent savings is often guaranteed. This is achieved by utilizing available computer software and implementing tire information management through the engineering deparatment.

Jan 1, 1983