Search Documents

By L. W. Bahney

The photograph, Fig. 1, shows the apparatus a little less than half size, consisting of a filtering-flask fitted with rubber stopper through which passes a bent glass tube, and an extraction-thimble fitted with rubber stopper through which passes a glass tube of 0.25-inch bore. Both tubes are connected by a short piece of rubber tubing. A section of a thimble is shown in the photograph ; the tube extends to within & in. of the tapered end. The object of using the thimble is to remove the acid from the beaker after all the copper has been precipitated. Time is saved, the copper is not exposed to the acid alone, and there are none of the losses attending ordinary filtration. I have accomplished these results by means of a piece of perforated platinum fastened in the end of a (0.25-in. bore glass tube and a filter-mat of asbestos, but after my supply of proper length fiber became exhausted I could not replenish it even after purchasing 14 lots from four different dealers. The above apparatus may be used to remove at least seven-eighths of a supernatant liquid from a settled precipitate without disturbing the latter. The application of the thimble is best shown by partly outlining the assay for copper, as follows: Dilute the acid solution of copper and other sulphates to 150 cc. in a 200-cc. Jena beaker, place on a hot plate, add 2 drops of concentrated HCl, then place a strip of aluminum in the beaker (this may be bent or straight, as desired). Connect the apparatus, as shown in Pig. 1, with a filter-pump having a strong suction. When the copper is precipitated, remove the beaker from the hot plate and insert the extraction-thimble alongside the strip of aluminum. The acid solution will be drawn through the porous tube. Wash the upper end of the aluminum strip with a jet of hot water, wash down the sides of

Jan 1, 1913

E. A. Loria (Product Metallurgical Engineer, Crucible Steel Co. of America, Pittsburgh)—In this interesting paper, our introductory work was quoted. We would like to call attention to our sequel paper on the experimental determination of oxygen in cupola-melted cast iron,20 which was not mentioned. Vacuum-fusion oxygen values (as well as hydrogen and nitrogen) were reported for nine heats of cast iron melted in the Battelle 10-in. cupola under normal operating practice and under oxidizing conditions. The oxygen analyses ranged from 12 to 68 pprn compared to the author's computed range of 10 to 80 ppm. The average amount of oxygen found in our irons was about 20 pprn and changes in the silicon content of the iron from 1.32 to 2.35 pct had no consistent effect on the oxygen content of the iron. The gas determination specimens were poured in split steel molds that produced a clean pin, 3/8 in. diam and 2 in. long. Because freezing was almost instantaneous, the pins were entirely white iron (nongraphitic). In the early stages of the investigation, the pins were transferred to a mercury-filled trap system immediately after pouring. This was done to collect gas evolved between pouring and analysis. However, it was found that during storage for 4 weeks gas evolution was negligible. Because the vacuum-fusion analysis was usually completed within 4 days of pouring, pins from later heats were not stored in the mercury-trap system. We found some evidence that cast iron picks up oxygen during long storage, because of rusting. Earlier work by the British Cast Iron Research Association has shown that cast irons may be stored for a long time without significant change in their oxygen content. The practical significance of this study (and our own) would be in the improvement of cast-iron quality. Has the author investigated this aspect and reached any conclusions on the effect of oxygen on the mechanical properties of cast iron? The second phase of our study was to determine the properties of the test bars poured simultaneously with the gas analysis specimens. We realize that there may be complicating factors attendant in this procedure.21 Results from many test specimens measuring chill depth, transverse flexure and deflection strength, spiral fluidity, and sensitivity to hardness of gray irons ranging from 12 to 68 pprn oxygen showed that the lowering of transverse strength was the only significant undesirable effect of high oxygen content. A statistical study of the chill test results21 showed that the iron containing 22 to 46 pprn oxygen had forced chill depths that were 2/32 in. below the expected value from their composition, and irons containing less than 16 ppm oxygen had forced chill depths averaging 1/32 in. greater than the expected chill depth. Higher oxygen contents, within the range of 12 to 68 pprn did not increase forced chill depth. With the wedge tests, there was a good linear relationship between carbon equivalent of the irons and their chill depth. The results indicated that oxygen contents below 50 ppm in the iron did not affect chill depth. With 50 to 70 ppm oxygen in the iron, oxygen appeared to have a slight graphitizing tendency. These results are in disagreement with the common belief in gray iron foundries that "oxidized irons" produce high chill depths. It would be appreciated if the author would comment on this subject. Gustaf Ostberg (author's reply)—In Fig. 1 the legend of line I should read 2 pct C, 1 pct Si. The author wishes to thank Mr. Loria for calling attention to his later work, which was published after the present paper was concluded. The range of oxygen contents quoted seems to agree well with the author's values. The lack of response to variations in silicon content is probably due to the fact that the oxygen content in most cases was below the saturation level. The absence of temperature dependence, even in the case of saturation, is understandable if the difficulty in formation and escape of the deoxidation products is taken into account.

Jan 1, 1960

By J. P. Murphy, T. E. Leontis

DURING the last few years, the trend in the aircraft and automotive industries has been toward higher and higher operating engine temperatures. This has created considerable interest in the effect of temperature on the properties of alloys. In the magnesium field, it has been recognized for many years that the addition of cerium imparts high strength and good resistance to creep at elevated temperatures. Beck,1 in his treatise on-magnesium, has summarized the work of German investigators. This includes the unpublished data of Menking, showing the increase in strength and hardness of extruded alloys containing 2 to 20 per cent Ce at temperatures from 200 to 300°C. (68° to 572°F.) and the results of Vosskühler, who demonstrated the improved resistance to creep of alloys containing 6 per cent Ce plus 2 per cent Mn and 0.5 per cent Ce plus 2 per cent Mn at 150°C. (302°F.). Wellinger and Keil2 have also reported the creep properties of a forged magnesium-cerium-manganese alloy at 200° and 250°C. (392° and 482°F.). Haughton and Prytherch have determined the tensile properties of various forged magnesium alloys containing cerium, cerium plus manganese, cerium plus calcium, cerium plus nickel, cerium plus nickel plus manganese, and cerium plus cobalt plus manganese at temperatures up to 290°C. (554°F.). Magnesium-cerium alloys have been used in some commercial applications. It is reported that an alloy containing 3 per cent Ce plus 0.5 per cent Mn plus 0.5 per cent Ca is being used on a forged impeller in Great Britain. Two forged parts made from an alloy with a nominal composition of 5 per cent Ce and 2 percent Mn have been found on the German .BMW-801D aircraft engine. These two forgings consist of a supercharger impeller and a rear cam-follower guide. In this country, several types of pistons have been made experimentally in both .the cast and the forged conditions from an alloy containing 6 per cent Ce plus 2 per, cent Mn and in the cast condition from an alloy of magnesium plus 10 per cent Ce. The cast pistons have been tested in various types of internal-combustion engines, with promising results. This paper presents the results of an extensive investigation on the properties of various cerium-containing magnesium alloys in both the cast and the forged conditions. Data are presented to show the beneficial effects of increasing amounts of cerium on the mechanical properties of magnesium at elevated temperatures. The effects of heat-treatment on the properties of these alloys and the attendant changes in the microstructure are discussed. The

Jan 1, 1946

By H. L. Couch, J. D. Lubahn

In decarburized mild steel, the strain hardening arising from 1/2 pct strain can he partly recovered by subsequent heating, even though re crystallization or grain growth does not occur. This recovery varies from 5 pct in an hour at room temperature to 70 pct at 800°C. The variation with temperature was qualitatively similar to that reported for copper, but occurred at lower temperatures. Except for the initial portion (Bazdschinger effect), the stress-strain curve following recovery can be superimposed on the original curve by shifting it to the left. In other words, the tensile behavior is essentially the same after straining and heating as if there had been less strain and no heating. The importance of this observation in understanding simultaneous deformation and recouery is explained. AN earlier investigation1 on copper showed that strengthening due to strain hardening was augmented by heating at moderate temperatures, but was diminished by heating at higher temperatures, Fig. 1. Auxiliary experiments1 indicated that recovery and strain aging are independent processes, which may proceed simultaneously, and whose effects are additive as indicated in Fig. 1. In order to study recovery by itself, similar tests were made on decarburized mild steel, where strain-aging effects are known2 to be absent. MATERIAL, TESTING PROCEDURE The specimens were made from rimmed, hot-rolled SAE 1020 steel 0.040 in. thick, by stamping out rectangular blanks and end holes, Fig. 2, and pack milling the reduced section. These were wet-hydrogen treated2 for 16 hr at 720°C to remove carbon and nitrogen completely and then heated 1 hr at 850°C in vacuum to stabilize the grain size. Auxiliary ex- periments showed that heating up to 800°C will not cause grain growth. They were prestrained 5 to 7.5 mils per in. using the special grips shown in Fig. 2. Such small strains are less than the "critical" strain for recrystallization and, therefore, will not cause recrystallization, even at high temperature. The recovery treatment after prestraining and before the retesting consisted of heating for 1 hr in wet hydrogen at the desired temperature. In one test, Huggenberger gages were used to define more accurately the loading and unloading curves. Fig. 3 illustrates the creep during the early stages of unloading, the hysteresis due to cold stretching, and removal of hysteresis by heating.3 RESULTS The load-deflection curves had ratner widely differing shapes for different specimens, both before and after the recovery treatment. Some specimens showed perfectly smooth curves, Fig. 4, while others exhibited an inflection more or less suggestive of a yield point (Fig. 4 shows all extreme case). Some curves were much steeper than others; Fig. 5 shows two extremes. Some additional ex-

Jan 1, 1960

By A. J. Lynch, W. J. Whiten

Extensive research, ,development and plant application work has been done on automatic control systems for wet grinding and sulphide flotation circuits during the past twenty years. The result is that there is a good understanding of the process mechanisms, the effects which changes in different variables have on these processes, the procedure for design of control systems to satisfy particular objectives and the problems in the implementation of control systems. There is also an appreciation of the problems which are still to be solved. These are reviewed briefly in this paper. Other processes used for the beneficiation of fine particles have been studied in lesser detail. The control of dry grinding, coal flotation and gravity separation are mentioned briefly in this paper.

Jan 1, 1980

By Richard H. Jahns

Gem materials, comprising those minerals and closely allied natural substances used for personal adornment, for the fashioning of ornamental objects, or for other decorative purposes, have been valued in human commerce for thousands of years. Amber, jet, natural glasses, and at least 15 mineral species were sought and used by primitive man, and most of the materials in common use today were known well before the time of Christ. Their variety is remarkably great, and the traceable relationships among their respective sources, modes of occurrence, properties, and histories of production, preparation, and valuation are extremely complex. Their uses have been affected by numerous shifts in fashion, and from time to time by superstition, by decrees of church and state, by personal interpretations of religious significance, and by various presumptions concerning medicinal value and influence on human behavior (Ball, 1935, 1950; Kunz, 1913; Pogue, 1915; Whitlock, 1946). Thanks to their durability, portability, and relative scarcity, some gem stones have been employed as media of exchange, and the investment value of the more precious stones has long been recognized and exploited, especially in Asiatic and European countries. Demands for gem materials have stimulated trade among various peoples for centuries, and they also were responsible for much early geographic exploration. During more recent times they have prompted numerous geological studies and a considerable amount of research on the growth and properties of crystals. Apart from decorative uses, some naturally occurring gem materials also are employed directly in numerous fields of industry. Substances that are manufactured for gem or industrial uses are termed synthetic gem materials; most of these correspond in composition and crystal structure to certain minerals found in nature. Imitation materials are those whose use is based upon their resemblance to substances of different composition and greater intrinsic value. Gem stone is a designation commonly restricted to those materials suitable for personal adornment, and the complementary term ornamental stone is applied to the remaining materials not used industrially. This distinction is arbitrary and somewhat inconsistent, owing to numerous geographic differences and historical shifts in end uses. Further, there is a complete gradation between the category of ornamental stones and that of dimension stone. Substances that lose their identity in use are excluded from the gem category; thus a transparent crystal of beryl would not be classified as a gem stone if it were processed as a source of beryllium metal. The adjectives precious and semiprecious have been employed as a means for distinguishing different gem materials on the basis of recognized value. Diamond, emerald, ruby, and sapphire consistently have been regarded as precious stones, and in cut form they commonly are referred to as the noble gems. Opal, pearl, turquoise, and chrysoberyl also have been classed as precious at various times. In recent years, however, it has been increasingly recognized that no satisfactory distinction can be based upon assessed value or any group of specific properties, and now all gem stones normally are referred to as precious. Indeed, the tendency is to extend this term to include many of the so-called ornamental stones, and the designation semiprecious has been essentially discontinued. Unlike most mineral commodities of economic value, gem materials are little altered in processing for end uses. Some stones are used in essentially their natural form, and most are reshaped and polished without significant changes in their fundamental properties. Thus the preparation of gem and ornamental stones is intended chiefly to emphasize or enhance

Jan 1, 1983

By Erskine Ramsay

The following description of the Alabama coal-,fields is taken (with slight omissions) from the report " On the Warrior CoalField, by Henry McCalley, A.M., C. and M. E., Assistant State Geologist:" The coal lands of Alabama are of the great coal basin of the Ohio, or of the great Appalachian coal-field, and are estimated at 8660 square miles. They formed one connected field prior to the great Appalachian revolution, when there was pushed up through them long, narrow, anticlinal ridges which have been denuded into the present well-known anticlinal valleys, and thus this great field has been divided up into three more or less distinct parts. These parts were named by Prof. Tuomey, in 1849, the Warrior, the Cahaba and the Coosa coal-fields, respectively, from the names of the rivers which drain them. They are of very unequal size, the Warrior, with an area of 7810 square miles, being nearly ten times as large as the other two combined, and about two-thirds as large as the coal-area of Great Britain. This Warrior field is the most northwestern of the three coal-fields of Alabama, and comprises all of the coal-measnres in Alabama, northwest of the Alabama Great Southern railroad, or all of those drained by the Warrior and Tennessee rivers. The greater part of this field, almost all of it away from the present railroad lines, has never received more than a surface-examination. Still, we have in the Warrior coal-field one of the richest coal-basins of this or any other country. As a whole, the Warrior coal-field is a broad, shallow, tray-shaped depression, sloping towards the southwest, and with its southwest end covered by a newer formation and its southeast side, especially, complicated by folds and fractures. As is the case with all of our Coal Measures. it is composed of a series of sandstones. conglomerates, shales, slates and coal-seams, with some little limestone at several horizontal positions, but contains no thick bed of this last rock like the Measures of Pennsylvania and other States. The thickest conglomerates are near the bottom and top of the series, and hence these coals might be said to belong mainly to the

Jan 1, 1891

By K. J. Gill, P. Chiotti, J. T. Mason

Thermal, metallographic, and vapor pressure data were obtained to establish the pkase boundaries and the standard free energy, enthalpy, and entropy of formation for the compounds in the Y-Zn system. Three coinpounds with stoichiometric formulas of YZn, YZn2, and Y2Zn17 melt congruently at 1105", 1080°, and 890°C, respectively. Four compounds with stoiclziometric formulas of YZn3, YZn4, YZn5, and YZn,, undergo perztectic reactions at 905", 895", 870º, and 685ºC, respectively. Three eutec-tics exisl in this system with the .following eutectic temperatures and zinc contents in wtpct: 875ºC, 23.2 Zn; 1015ºC, 51 Zn; 865ºC, 82 Zn. The YZn, pkase undergoes an allotropic transformation. In the two phase YZn2 -YZn alloys the trans.formation gives a weak thermal arrest at 750°C, whereas in the two phase YZn2-YZn3 alloys no thermal arrest is observed and the transformation occurs over a temperature range below 750°C. At 500°C the free mzergies of formation per lnole vavy from —18,090 for YZn to —53,430 fov YZr11 and corresponding enthalpies vary from -24,050 to -92,080. The free energies and enthalpies per g atom as a function of composition show a maximum for the YZn2 phase; the 500°C values are -9580 and -13,180, vespectively. 1 HE only information found in the literature on Y-Zn alloys was the observation reported by Carlson, Schmidt. and speddingl that Y-20 wt pct Zn forms a low melting alloy. The alloy was produced by the bomb-reduction of YF3 and ZnF2 with calcium in an investigation of methods for producing yttrium metal. The solubility of yttrium in zinc has been determined by P. F. woerner2 and reported by Chiotti, Woerner, and Parry.3 In the temperature range 495" to 685°C the solubility may be represented by the relation In these equations N represents atom fraction of yttrium and T is the temperature in degrees Kelvin. The purpose of the present investigation was to establish the phase diagram for the Y-Zn system and to determine the standard free energy, enthalpy, and entropy of formation for the compounds formed. MATERIALS AND EXPERIMENTAL PROCEDURES The metals used in the preparation of alloys were Bunker Hill slab zinc, 99.99 pct pure, and Ames Laboratory yttrium sponge. Arc-melted yttrium buttons contained the following impurities in parts per million: C-129, N-12, 0-307, Fe-209, Ni-126, Mg-13, Ca < 10, F-105, and Ti < 50. Some of the alloys containing 70 wt pct or more of Zn were prepared from yttrium containing 5000 ppm Ti as a major impurity. Tantalum containers were found to be suitable for all alloys studied and were used throughout the investigation. The pure metals, total weight about 30 g, were sealed in 1 in. diam tantalum crucibles by welding on preformed tantalum covers. A 1/8 in. diam tantalum tube was welded in the base of each crucible for use as a thermocouple well. Welding was done with a heli-arc in a glove box which was initially evacuated and filled with argon. The sealed crucibles were enclosed in stainless steel jackets and heated in an oscillating furnace at temperatures up to 1150°C. Homogeneous liquid alloys were obtained within a half hr at these temperatures except for alloys containing less than 20 pct zinc. The latter alloys were held at 1000º to 1100°C for 2 to 3 days in order to obtain equilibrium. After the initial equilibrations the tantalum crucibles containing the alloys were removed from the steel containers and used directly for differential thermal analyses. Further annealing heat treatments for alloys in which peritectic reactions were involved were carried out in the thermal analyses furnace. After thermal analyses the tantalum crucibles were opened and the alloys sectioned and polished for metallographic examination. In the following discussion alloys referred to as "quenched" were obtained by quenching the sealed stainless steel jacket containing the tantalum crucible and alloy in water. The differential thermal analyses apparatus used was a modified version of the one described in an earlier paper., The graphite crucible was replaced by an inconel crucible, the nickel standard and sampie container were separated by a 1/8 in. MgO plate, no getter was used, and provisions were made to

Jan 1, 1963

By E. P. Bayer

MESABI RANGE ore is mined largely by the open-pit method. This involves having available at all times sufficient working places which in combination will produce ore of guaranteed analysis. Fast- loading power shovels turn out under favorable conditions 1000 tons per hour from each unit. Each unit loads ore differing materially in analysis from that loaded by the others, One may load high grade, another low grade, and another may be in a mixed bank with the lead ore so placed that the product must be mixed at the shovel before it is loaded into cars. In such cases the bank is combed with the bucket, the door being left open to permit the material to fall through.

Jan 1, 1937

A SERIES of papers on strategic and otherwise important mineral products was prepared some ten years ago under the joint auspices of the Committee on Foreign and Domestic Mining Policy of the Mining and Metallurgical Society of America and the Committee on Industrial Preparedness of the American Institute of Mining and Metallurgical Engineers. These papers were later published in a joint volume entitled International Control of Minerals (1925). Amongst them was one on manganese. The Subcommittee on Manganese prepared its paper in two forms. One was intended for inclusion with the series above referred to and approached its subject more particularly as an international problem. The other dealt more definitely with manganese as an element in the problem of national defense. This last was first written under date of January 24, 1924 as a confidential report, for and at the request of the War Department. It was later released and published, in slightly modified form, as a separate pamphlet by the Industrial Preparedness Committee of the American Institute of Mining and Metallurgical Engineers. After the lapse of eight years, in view of the vital position of manga-nese in the problem of industrial preparedness against a war emergency, the War Department made a request to have the conclusions of 1924 reviewed and brought up to date. To comply with this request the manganese subcommittee was reconvened (with a somewhat changed personnel) and exhaustive studies were once more made of the entire subject of manganese. A new report, with specific recommendations, was submitted to the War Department in February, 1932. This second report is now herewith released for publication. Certain specific conclusions and recommendations as expressed to the War Department are omitted. Otherwise the report stands as prepared and submitted by the manganese subcommittee of 1931. The members of this committee were: C. Minot Weld, Chairman, R. C. Allen, Arthur S. Dwight, J. W. Furness, D. F. Hewett, Reno H. Sales, Theodore Swann and Scott Turner. ARTHUR S. DWIGHT, Chairman, Committee on Industrial Preparedness.

Jan 1, 1933

By B. M. Larsen, W. E. Shenk

THIS paper describes a method of reversal control of the open-hearth furnace that obtains in practice those effects considered below as essential to a completely automatic control, without appreciable interference with the natural rise and fall in temperature of the regenerative portions of the furnace system. Growing out of some studies of radiation pyrometry in open-hearth regenerators, it was developed during 1934-1938, and has been successfully applied to a number of commercial furnaces. The goal of open-hearth furnace operation is the highest rate of production of steel of proper quality consistent with good refractory life and fuel economy. This requires rapid heat transfer from furnace to charge, which in turn is dependent upon heating the furnace refractories to the highest safe operating temperature. The greater the heat input to the melting chamber, the sooner this limiting temperature will be reached, so that control methods in general that are designed to protect against overheating of refractories should help to maintain maximum fuel input and production rate. For the typical open-hearth system, with fixed regenerator capacity and with rate of fuel input usually restricted in its range of variation, our basic assumption is the idea that the only other important variable that is, the time interval between successive reversals-should also be held constant or within a small range. The present reversal control was designed therefore so that, under normal operating conditions, no arbitrary limitation is imposed other than to keep the reversal interval within the optimum time range. However, since a near approach to completely automatic operation involves protection of refractories through the balancing of furnace end temperatures as well as emergency protection against temperature peaks above some upper limit, it was also felt essential to employ, as an integral part of the control unit, a temperature-measuring instrument to register the true temperature of the refractory surfaces at some critical region in the hot ends of the regenerative zones. As the basic elements of the control, we thus have one "maximum" and one "minimum" time relay and a potentiometer recorder-controller, combined with switches and relays to operate as follows: x. Reversal normally occurs within an optimum range limited by the maximum and minimum settings to about 4 to 6 min. variation, but the actual interval usually is less variable and closer to the minimum setting. 2. The margin between minimum and maximum time is utilized, together with a "floating temperature limit" in the potentiometric control instrument, to correct any

Jan 1, 1945

By Donald B. Gillies

TO me a graduating class of engineers constitutes one &apos; of the finest inspirations I can imagine. You have finished your four- year scholastic career and are starting out in competition with thou- sands of other young men from other universities to make your mark. Be- cause of your training you men are such an essential part of our present- day civilization that a great weight of responsibility rests on your shoulders, especially at this time, for this is an engineering era. Today, it is the engineer who dreams the dreams and makes our civilization better. It&apos;s the engineer who carries those dreams into realization and fulfillment. No matter where we go in business and industry, we find- engineers in key positions, charged with great responsibilities.

Jan 1, 1939

By Robert T. Pring

In addition to the humanitarian aspects of a dust-control program, certain economic benefits are becoming more fully recognized and now furnish a greater incentive to the mill operator to eliminate the dust from his plant. It is well known that a favorable working environment promotes increased efficiency and improves the morale of employees, with a consequent decrease in labor turnover rates. One progressive mining company&apos; estimates its direct and indirect labor turnover costs at from $40 to $50 per man; for skilled labor, such as machine operators, the cost may approach $100 per man. While these figures may not be typical of every plant, they do indicate a potential savings in operating costs. Dust signifies waste; its elimination decreases maintenance costs of mechanical and electrical equipment; its recovery is often justified from the standpoint of values contained in the collected material, although in large-scale milling operations handling low-grade ore this may not be an important factor, Perhaps the most significant trend in industrial sanitation is that dust-control equipment and procedures are becoming recognized as integral parts of the mill flowsheet. Exhaust ventilating systems are now afforded equal care in design and maintenance to that given other machinery more closely related to the Process. Methods of Dust Control "Dust control" is a general term descriptive of a number of methods used singly or together to prevent particulate atmospheric contamination. These methods are: in order .of their desirability, as follows: 1. Change of process. 2. Isolation of process. 3. Wet methods. 4. Ventilation. a. Local exhaust ventilation. b. General ventilation. 5. Personal respiratory protection. In ore-concentration plants it is seldom prac tical to change a process to eliminate the dust it creates It is possible in some cases to isolate a particular dust-producing operation from the rest of the plant, provided that constant attention on the part of the operators is not required. Frequently water is used in fine crushing and fine grinding, primarily to facilitate the processing of the ore and incidentally to allay the dust produced. Wet methods, however, are not feasible in coarse and secondary crushing operations, because of the relatively great volume of water required in instantly wetting each freshly fractured rock surface. Such quantities of water would entail conveying and storage difficulties. Local exhaust ventilation is the most effective and most commonly applied control measure, wherein directional air currents through the zone of dust production draw the contaminants into a duct system. Unfortunately, only a limited amount of reliable information on exhaust ventilation is available.2-5 of necessity these publications are rather general, being primarily concerned with engineering fundamentals. While many organizations have successfully

Jan 1, 1943

By Robert T. Pring

In addition to the humanitarian aspects of a dust-control program, certain economic benefits are becoming more fully recognized and now furnish a greater incentive to the mill operator to eliminate the dust from his plant. It is well known that a favorable working environment promotes increased efficiency and improves the morale of employees, with a consequent decrease in labor turnover rates. One progressive mining company&apos; estimates its direct and indirect labor turnover costs at from $40 to $50 per man; for skilled labor, such as machine operators, the cost may approach $100 per man. While these figures may not be typical of every plant, they do indicate a potential savings in operating costs. Dust signifies waste; its elimination decreases maintenance costs of mechanical and electrical equipment; its recovery is often justified from the standpoint of values contained in the collected material, although in large-scale milling operations handling low-grade ore this may not be an important factor, Perhaps the most significant trend in industrial sanitation is that dust-control equipment and procedures are becoming recognized as integral parts of the mill flowsheet. Exhaust ventilating systems are now afforded equal care in design and maintenance to that given other machinery more closely related to the Process. Methods of Dust Control "Dust control" is a general term descriptive of a number of methods used singly or together to prevent particulate atmospheric contamination. These methods are: in order .of their desirability, as follows: 1. Change of process. 2. Isolation of process. 3. Wet methods. 4. Ventilation. a. Local exhaust ventilation. b. General ventilation. 5. Personal respiratory protection. In ore-concentration plants it is seldom prac tical to change a process to eliminate the dust it creates It is possible in some cases to isolate a particular dust-producing operation from the rest of the plant, provided that constant attention on the part of the operators is not required. Frequently water is used in fine crushing and fine grinding, primarily to facilitate the processing of the ore and incidentally to allay the dust produced. Wet methods, however, are not feasible in coarse and secondary crushing operations, because of the relatively great volume of water required in instantly wetting each freshly fractured rock surface. Such quantities of water would entail conveying and storage difficulties. Local exhaust ventilation is the most effective and most commonly applied control measure, wherein directional air currents through the zone of dust production draw the contaminants into a duct system. Unfortunately, only a limited amount of reliable information on exhaust ventilation is available.2-5 of necessity these publications are rather general, being primarily concerned with engineering fundamentals. While many organizations have successfully

Jan 1, 1943

By D. K. Crampton, H. l. Burghoff, J. T. Stacy

The study of copper alloys of the age-hardening type has received considerable attention, and, among the alloys which the authors have, considered, those containing small amounts of nickel and phosphorus as essential constituents seem especially interesting. Such alloys have attractively great capacity for being hardened and also have relatively high electrical and thermal conductivity in the hardened state. In addition, it has been found that the increase in hardness and strength imparted by aging can be greatly augmented by cold-working, so that excellent combinations of conductivity and strength are obtainnble. In view of the possible importance of the alloys, it was considered desirable to investigate the solubility relationships in the copper-rich portion of the copper-nickel-phosphorus system. This paper present&apos;s some of the results obtained in this investigation to date and also gives propertics of typical alloys that appear to be of commercial interest,. Review of literature Copper-nickel System,.—The binary coppcr-nickcl system has long been known to consist of a series of simple solicl solutions, copper and nickel being miscible at all tempcrat&apos;ures and concentrations. This was establisl~cd by Guertler arid Tammannl in 1907 and confirmed by Tafel2 in 1908. Copper-phosphorus System.—The copper phosporus system has been studied by numerous investigators, so that the copper-rich portion is now definitely known. As most recently determined by Lindlief," his system has a cutectic at 8.38 per ccnt P, cuteetic temperature being 714° C. Components of the cutectic are Cu3P and alpha solid solution. Solid solubility of phosphorus in copper, according to Mertz arid Mathewson decreases from a maximum of about 1.75 per cent at 714&apos; C. to about 0.6 per cent at 300&apos; C.

Jan 1, 1940

By D. K. Crampton, H. l. Burghoff, J. T. Stacy

The study of copper alloys of the age-hardening type has received considerable attention, and, among the alloys which the authors have, considered, those containing small amounts of nickel and phosphorus as essential constituents seem especially interesting. Such alloys have attractively great capacity for being hardened and also have relatively high electrical and thermal conductivity in the hardened state. In addition, it has been found that the increase in hardness and strength imparted by aging can be greatly augmented by cold-working, so that excellent combinations of conductivity and strength are obtainnble. In view of the possible importance of the alloys, it was considered desirable to investigate the solubility relationships in the copper-rich portion of the copper-nickel-phosphorus system. This paper present&apos;s some of the results obtained in this investigation to date and also gives propertics of typical alloys that appear to be of commercial interest,. Review of literature Copper-nickel System,.—The binary coppcr-nickcl system has long been known to consist of a series of simple solicl solutions, copper and nickel being miscible at all tempcrat&apos;ures and concentrations. This was establisl~cd by Guertler arid Tammannl in 1907 and confirmed by Tafel2 in 1908. Copper-phosphorus System.—The copper phosporus system has been studied by numerous investigators, so that the copper-rich portion is now definitely known. As most recently determined by Lindlief," his system has a cutectic at 8.38 per ccnt P, cuteetic temperature being 714° C. Components of the cutectic are Cu3P and alpha solid solution. Solid solubility of phosphorus in copper, according to Mertz arid Mathewson decreases from a maximum of about 1.75 per cent at 714&apos; C. to about 0.6 per cent at 300&apos; C.

Jan 1, 1940

By Frank Van Horn

IT is customary to ascribe two general modes of occurrence to natural gas, namely shale. gas which, as the name indicates, is found in&apos; shale, and reservoir gas, which occurs ill sandstone, conglomerate and dolomitic limestone. Both of these types are found in the Cleveland district. The shale gas has been produced on a small scale for a long period of years, probably dating back as far as 1883. Shale gas is a low-pressure gas, small in volume with variable pressure, and is limited to no definite horizon. It is generally independent of oil, may last for a long time, and is not dependent to any great extent on the structure of the rocks. There are many such wells in the district which range from 400 to 1,840 ft. in depth, although most have been completed at about 800 ft. This indicates that the wells pass through the Cleveland and Chagrin shales into the Huron or Portage shale of the Upper Devonian. During the last 2 years great interest has developed in a deeper-seated reservoir gas. What is commonly called reservoir gas is generally a high-pressure gas occurring in large volume at a definite horizon. Oil may, or may not, be associated with the gas, and in most regions in which reservoir gas is found, the geological structure is of great importance. This type of gas occurs in all large fields such as those of West Virginia which have been supplying Cleveland until the recent discovery of local gas at great depths in commercial amounts.

Jan 1, 1917

By Pol Duwez, Ellis P. Frink, Paul Pietrokowsky

Ti-Au alloys in the composition interval 0 to 66 213 atomic pct Au have been studied over a temperature range from 400° to 1500°C. A partial phase diagram has been established from micrographic and macroscopic observations. All intermediate phases, Ti3Au, TiAu, and TiAu., exhibit open melting maxima. It has been observed that small additions of gold lower the allotropic transformation temperature of titanium. The P solid solution decomposes eutectoidally to a solid solution plus Ti3Au. The solubility of gold in a solid solution decreases with temperature. THERE have been several papers in the literature pertaining to the alloy system Ti-Au. However, a comprehensive study of this interesting constitu- tion diagram has not been conducted. Previous investigations have been concerned with the crystal structure of intermediate phases or partial phase diagrams. This paper represents a partial constitution diagram, Ti-TiAu,, the first portion of an investigation of the entire binary system. Laves and Wallbaum&apos; reported the intermediate phase Ti,Au to be isomorphous with CuAu, L12 type. In a more recent paper, Duwez and Jordan&apos; have concluded that TiAu has an atomic arrangement which is related to Cr,Si. The intermediate phase

Jan 1, 1957

By B. Ladanyi

The problem of rock behavior under concentrated loadings has been the subject of a number of studies in the past and has been receiving increasing attention by rock mechanics investigators in recent years. Its application covers various fields, but main interest in its solution has arisen in connection with the problems of drilling, bearing capacity, and rock testing. These widely different purposes and fields of interest probably have been one of the reasons why, in spite of the large amount of published experimental data and several theoretical studies, there are still many points which need further clarification. Another reason for this situation undoubtedly is due to the fact that the rock behavior in indentation is complicated by a great number of influencing factors. Experimental evidence shows that, depending on the rock type (mechanical properties, porosity), environment (ambient effective pressure, pore fluid, temperature), and the type of loading (indenter shape, initial embedment, load level, loading rate), the rock response to indentation may vary within very large limits. The widely different rock behavior has made it impossible up to now to treat the problem with a consistent single mathematical theory, but has required instead a series of simplified models covering only certain most important events in the failure sequence. As far as the theory of rock indentation is concerned, this chapter does not add much new information. Its main purpose is, however, to state the indentation problem in a general manner and to indicate which points need to be studied in more detail before its definite solution is attempted. Also, since excellent reviews of the state-of-art of rock indentation in drilling have recently been given,1-4 this will not be repeated here, and only references pertinent to the points of the problem under study will be quoted. The theoretical part of this study attempts to give a quantitative evalu-

Jan 1, 1972

By Francis T. Freeland

The deeper workings of the Leadville mines show refractory ores, consisting principally of sulphides of iron, lead, and zinc, carrying silver, in place of the easily reduced carbonate ores lying nearer the surface. The largest and most extensively developed deposit is that of South Iron Hill.* It lies on the north side of California Gulch,

Jan 1, 1886