Search Documents

By Robert Mehl

PART I. ORIENTATION RELATIONSHIPS IN OXIDE LAYERS Oriented overgrowths and intergrowths among both metallic and nonmetallic substances have been recognized and studied for well over a century. The work of Widmanstätten in 1808 on the geometrical struc-ture in meteorites, a structure known by his name, demonstrated that oriented intergrowths can occur in purely metallic systems. This fact led to much of the early microscopic study of alloys, contributing greatly to the advance of physical metallurgy. The problem has been attacked again in recent years in a comprehensive fashion, with the object of dis-covering what atomic movements may occur during phase changes in alloy systems. Much of this work has appeared in the A.I.M.E. TRANS-ACTIONS in a series of papers published by Mehl and coworkers beginning in 19311. Although many aspects of this general problem remain unsolved, it may be said that the orientation of a new phase forming by precipitation from solid solution or by transformation invariably bears, a unique relationship to the orientation of the phase from which it formed, and that similarity in atomic patterns on atomic planes in the two phases play an important part in determining the orientation relationship. Analogous orientation relationships exist in oriented intergrowths in nonmetallic systems-mineral or inorganic. In 1827 Haidinger2 dis-covered natural intergrowths of hematite and magnetite, and demon-strated that the rough form of the magnetite octahedrons was delineated by small crystals of hematite, of which the basal (00.1) planes lay parallel to the octahedral cleavage planes of the magnetite. The description of this orientation relationship was later completed by von Rath3, who showed that the edge (00-1):(10-1) in hematite lies normal to the [111]

Jan 1, 1937

By Takeyasu Ito, Mayumi Someno, Kazuhiro Goto

SINCE the pioneering work by Kiukkola and Wagner,1 many experiments have been reported on solid electrochemistry at elevated temperatures. However, the studies have been confined to experiments under isothermal conditions. One may conceive many situations under nonisothermal conditions. With two different temperatures T1, and T2 at the two electrodes, the electromotive force, E of a Galvanic cell will be expressed by the following equation under a steady state heat transfer in solid electrolytes of zirconia-lime and thoria-lime. E = ^ $ l&-dGO2+a(T2-Ti) [1] where tO2- is the transference number of oxygen ions in the electrolyte, Go, is the chemical potential of oxygen, and a is the coefficient of the thermoelec-tromotive force due to the temperature difference. The objective of the present study was to evaluate the coefficient of the thermoelectromotive force for zirconia-lime and thoria-lime under isobaric condition. The physical meaning of this coefficient is out of the scope of the present communication. The experimental cell assembly is schematically shown in Fig. 1. The zirconia-lime electrolyte tube and thoria-lime electrolyte tube were 8.0 mm OD and 5.0 ID, from commercial sources with chemical analyses of 94.8 wt pct ZrO2, 3.85 pct CaO, 0.83 pct SiO2, 0.25 pct TiO2, and 0.05 pct Fe2O3; and 95.0 pct ThO2, 4.0 pct CaO and rare earth metal oxides, respectively. The specific gravity was 5.5 g per cu cm for zirconia-lime and 9.8 g per cu cm for thoria-lime. Original powder size before shaping and sintering the tube was several microns for both electrolytes. The distance separating the two electrodes was 4.0 or 5.0 cm. Platinum wire of 0.5 mm diam was used for the electrodes. The temperature gradient was controlled by heating one electrode with a small heating coil of nichrome wire. The temperatures at the two electrodes were measured with two calibrated Pt-13 pct Rh:Pt thermocouples, directly contacting the two platinum electrodes. The atmosphere was either air or pure oxygen. The partial pressure of oxygen in air was considered equal at the vicinities of the two electrodes, with negligibly small thermal segregation in the gas phase. The difference of the chemical potential of oxygen was controlled only by the temperature difference at the two electrodes and not by the oxygen pressure difference. The temperature ranges were 600" to 1200°C for zirconia-lime and 850" to 1200°C for thoria-lime electrolytes. Fig. 2 shows the relation of the measured electromotive force and the difference of the oxygen chemical potential at the two electrodes for zirconia-lime and thoria-lime electrolytes. The electromotive forces in the figure were measured by a *0.05 mv potentiometer. The chemical potential difference was calculated by the following equations.'

Jan 1, 1970

By B. W. Frazier

This interesting application of the laws of thermodynamics to metallurgical practice has not been discussed by any writer, within my reading, except the late Prof. Callon of Paris. In his Cours de Machines," Prof. Callon has given a short but lucid discussion of this subject in the admirably clear style for which he was remarkable. Although the interest attached. to the subject is rather theoretical than practical, I have thought that an attempt to explain the mechanical action exerted in the hot-blast oven might not be entirely devoid of utility, especially in the suggestions which it involves. The statement, that the mechanical work performed in heating the blast is, when high temperatures are produced, considerably greater than the work performed by the blowing-engine, may seem incredible to many who are practically acquainted with the subject, appearing, as it does, to conflict with the results of their experience. It is, nevertheless, literally true, and I shall attempt in this paper to prove it, and to explain why it has not rendered itself palpably manifest in practice. Before proceeding to the mathematical demonstration, it will be well to recall to mind the definitions of some terms employed by writers in mechanics and thermodynamics. The actual energy of a moving body, as defined by Rankine, is the work which it is capable of performing against a retarding resistance before being brought to rest, and is equal to the energy which must be exerted on the body to bring it from a state of rest to its actual velocity. The value of that quantity is the product of the weight of the body into the height from which it must fall to acquire its actual velocity.

Jan 1, 1879

By W. J. Parton

THE efficient recovery and preparation of small sizes of anthracite called No. 4 Buckwheat (3/3 2 by 1/3 2 in.) and No. 5 Buckwheat (1/3 2 in. by 0), present a difficult problem to the anthracite operators. In many instances preparation of these sizes, particularly No. 5 anthracite, is extremely inefficient. In many of the older preparation plants, inadequate facilities, and often none at all, were provided as an integral part of the plant for cleaning this fine anthracite. Consequently, much of the material smaller than s, 32 in. was discarded. As the demand for these sizes increased, facilities for preparing the fine sizes were often crowded into existing structures with consequent sacrifices of capacities and efficiency. In addition to this condition, the methods of preparing the finest sizes are being developed in an attempt to improve their efficiencies. Because the demand for small sizes of anthracite still is increasing, many operators would benefit by investigating and improving the cleaning equipment employed on these sizes.

Jan 1, 1949

By Edward W. Parker

IF one is to place any credence at all in the reports published in the daily press, the subject of conservation has been a very lively topic of conversation during the past 60 days, and it does not appear that the temperature of the summer months has been in any way moderated by the discussion. It is a subject in which we are all vitally interested and to which, so far as our mineral resources are concerned, both the Institute and the Geological Survey have liberally contributed. The report of the National Conservation Commission, appointed by President Roosevelt, contains a series of papers on the conservation of mineral resources, all of which were prepared by members of the Geological Survey and were compiled largely from information previously collected by that Federal bureau in the performance of its regular duties. It is not the purpose of this paper to reiterate in extenso any of the material already published. The contributions of the Survey officials to the Commission's report have been published in a separate document as Bulletin No. 394. This docunient is for free distribution and may be obtained upon application to the Director of the Survey. In the preparation of this paper I desire merely to make a few suggestions regarding the possible necessity of some restraint upon or control of one branch of the mining industry with which I have been somewhat closely associated for the past 20 years-that of coal. Most of the members of the Institute are cognizant of the suits brought by the government against the anthracite-operators in Pennsylvania, or the combination of interests commonly known as the ? hard-coal trust." No defense of any illegal combination in restraint of trade is intended, but there are some facts which should not be lost sight of, and unfortu-\

Nov 1, 1909

By David Baker

Our large modern blast-furnaces, equipped with ore-bins, larries and mechanical means for putting stock into storage, withdrawing it therefrom, and charging it at the tunnel-head, are indeed wonderful in capacity; yet, it is admitted that, with some notable exceptions, they have disappointed us in economy—that is, in the items of low fuel-consumption, uniformity of product, freedom from slips, and reduced cost of repairs and relining. The manager who estimated the cost of pig-iron to be made in a modern plant, by taking the costs of the hand-filled furnace and deducting the amount to be saved by the mechanical appliances, has been surprised, in many cases, to find that unfavorable results in these items of economy have greatly reduced his expected gains. Is there any reason why the fuel-consumption should be greater for a modern furnace than for an older stack using the same mixture ? Certainly the equipment is much more complete, and the trouble, therefore, must lie in the management or in the character of that equipment. Everybody knows that intelligent and vigilant management is a prime requisite: that any neglect of a detail, though it may not be felt that day or week, will surely sooner or later make its appearance as an increased item of cost. But to hold the furnace-maaager responsible for the relatively poor work of the modern blast-furnace would be, I am convinced, a great injustice. For its management has received much more study and care than was given to the older types. Many furnace-managers have lost their health through worrying over this problem, and some hare lost their positions, being held responsible for results made inevitable, as I believe, by the equipment provided for them.

Jan 1, 1905

By Victor G. Hills

CONTRARY to what seems to be the general impression, the island of Cyprus was not named for the metal copper, but the reverse was the case. The origin of the name is entirely lost. The ancient city Kition, the birthplace of Zeno, is supposed to be the same as Kittim mentioned in Gen. x, 4; Jeremiah ii, 10 and Ezekiel xxvii, 6, and Josephus states that this name seems to have been applied to the city and also to the island itself. Cyprus is 50 miles off the coast of Asia Minor. The mountains on the mainland are plainly visible across the sea from where I write six miles from the shore of Morphou bay. It is 200 miles from Joppa the port of Jerusalem, and 250 from Port Said. The shape of the island is like a lizard, the tail pointing directly toward the old city of Antioch near the northeastern corner of the Mediterranean. The island was once heavily timbered. Among the great trees the cedars were said to even excel the famous cedars of Lebanon. The Odyssey refers to it as the "sweet smelling island" and makes other references. But the continual wars of every race and age completely stripped it of its timber, and for centuries it has been woefully barren. There are two ranges of mountains. One borders the north coast and runs out in a slim rocky ridge forming the "tail." The other occupies the southwestern part of the island, the highest point being Mt. Troodes 6600 ft. high, sometimes called Mt. Olympus. Whether or not it be the Mt. Olympus, anyway right around there the ancient gods and godesses frequently "started things." These peaks are in plain sight 10 miles south from where I live.

Jan 1, 1926

By AIME AIME

THE fall meeting at El Paso this year (Oct. 13¬15) will be of unusual interest due to the international atmosphere imparted by the many engineers from Mexico, who are making arrangements to attend this meeting. The meeting will be held jointly with the Western Division of the American Mining Congress. Cooperating in the program will be the representative society of Mexican engineers known as Centro National de Ingenieros of Mexico City, who are plan¬ning on sending many delegates and well known Mexican engineers to the convention. The cooperation of the West Texas Geological Society and the American Association of Petroleum Geologists has also been secured. Brent N. Rickard, manager of the El Paso Smelting Works of the American Smelting & Refining Co. at El Paso, Tex., is general chairman in charge of arrangements. He is receiving splendid cooperation from the Mining Department of the El Paso Chamber of Commerce and from the business people of El Paso, who feel highly honored in having these mining societies meet with them this year.

Jan 1, 1930

By S. A. TAYLOR

THERE is probably no other mineral industry of which the public has as much information and misinformation as it has of the coal industry. Unfortunately, however, the general public's knowledge of the coal industry, outside of the particular kind of coal it is accustomed to, by reason of use, is largely made up of information received from newspaper and popular magazine articles, in which the mine workers are depicted as overworked and mistreated men, and the coal operators as "coal barons." Those who have any specific knowledge of exact conditions in the coal industry know how unjust and un- fair such an opinion of the coal industry is, not only to the miner but to the operator as well. Many reporters and writers of magazine articles are misled by statements regarding the condition of the miners that are exaggerated and not founded on facts and, if an investigation of the conditions of the miner's work, his habitation and surroundings were fairly made, it would at least compel more truthful statements by those who write for public reading. That such an investigation would not reveal anything that was wrong, or anything to be censured or cured, no one, I think, would maintain, but I do think that any fair investigation of the facts would show that conditions in and around the newer and later-developed coal mines and communities would compare favorably with those of manufacturing districts, and that where the mines and com- munities are old and not very attractive places to work, or live in, they carry with them other considerations, compensating for these conditions, and cannot be remedied by reason of a lack of sufficient coal to warrant economically any costly changes.

Jan 1, 1926

By Walter C. Lawson

The primary objective in laying track in panel sections is to reduce the number of track laborers required. This is possible because the work is mechanized. Moreover, because the work is mechanized and each of the operations needs only a few men, and each is self-contained, the work can be carried on at night as well as in daylight; therefore, the method provides a means of preparing tracks on more than one shift. The laying of tracks in open pits and quarries in panel sections is not new but new methods have been made possible by the introduction of new types of equipment. The purpose of this paper is to describe the methods that are followed in the Morenci open pit. General Mining Operations Full-scale ore production at Morenci is about 50,000 tons daily. The normal yearly output of ore and waste is 32,000,000 tons, of which 30,000,000 tons is handled by rail haulage. This requires the building of approximately 47 miles of loading and other temporary tracks during a 12 months' period (Fig I). Broken ore and waste is loaded into 90-ton capacity dump cars with 5-cu-yd full-revolving electric shovels. Shovel banks are uniformly 50 ft high. They are blasted with churn drill holes and the broken material from a blast is loaded out with two shovel cuts, the first one being called (locally) the "splatter" cut and the second one the "clean-up" or "face-up" cut. When a shovel is making its clean-up cut, the loading track is about 70 ft from the toe of the bank and, under normal conditions, a bank is blasted against it without removing the track. It is thus evident that each track is used for two shovel cuts before relocation is necessary, inasmuch as a single position serves for both the clean-up cut prior to blasting and for the splatter cut following the blast. The normal advance of a solid bench by a single blast is 40 ft (Fig 2). Preparation OF Panel Grade In preparation of panel grades bulldozers and rooters are used for the bulk of the work and an auto-patrol road grader for the final stage. At Morenci, bulldozers have always been used for track-grade preparation, but before the introduction of the other two types of equipment grades were uneven and irregular at best, and always necessitated a big gang of track laborers to hand-block under the ties with rocks after a track was laid into place. High blocking also made poor track because of instability and caused frequent derailments. Under these conditions derailments were generally bad as re-railing became difficult. Much track was torn up and many tics broken in the process. The inadequacy of the hand-blocked track, together with the inefficiency of hand blocking, constantly pointed, to the desirability of reducing the amount of labor required, so various means were tried to improve conditions, such as wood

Jan 1, 1949

By C. C. Wright, R. J. Day

ALTHOUGH data on the exact tonnage of recoverable coal silt are not known, the quantity produced in 1943 was estimated to be over five million tons for the anthracite region of Pennsylvania alone. Since that time the recovery of the No. 5 buck- wheat size previously included in silt estimates has increased greatly thus reducing the total silt tonnage. As a compensating factor, however, the methods of recovering silt previously escaping into the rivers and streams have been markedly improved so that the net figure may not have changed materially. Comparable estimates for bituminous coal are lacking, but undoubtedly the silt represents a significant tonnage. With the trend toward increased wet cleaning of the smaller sizes of bituminous coal, it is to be expected that even greater quantities of silt will be available in the future. The raw silt from anthracite collieries usually contains a high mineral matter content, but technological developments in fine coal cleaning have been making rapid advances and it appears probable that more extensive use of these methods will be employed in the near future. Bituminous coal silt in many instances contains a similar high mineral matter content. As with anthracite silt, however, the cleaning of this material, where necessary, appears both technologically and economically feasible. With a view to upgrading the size and value of silt, considerable laboratory and pilot plant work has been conducted by a number of organizations on what is commonly known as pelletization. Actually the process is one of extrusion in which the moist silt is extruded from a die in the form of rods, which usually break into relatively short lengths-a few inches long-as they fall from the die. Fig I is a photograph of some extruded 3/8-in. diam pellets and of the anthracite silt from which they were produced. This technique of producing larger sized material from fines is by no means new, having been used extensively by the industrial carbon and clay industries for years.' The application of the process to coal silt appears, however, to be relatively new. The first major program of investigation dates back only to July 1945, when a group of engineers representing the Anthracite Institute, The Pennsylvania State College and the J. F. Pritchard and Co. conducted preliminary tests on the extrusion of anthracite silt at the Floridin Co. plant at Warren, Pa. Since that time these three organizations-individually, together, and in co- operation with other interested groups- have actively pursued work on various phases of the problem. Much of the early history and details of the laboratory and pilot plant work by the Anthracite Institute, has been reported by Mulcey and Eckerd.2 It is the purpose of this paper to report additional information on the process, especially with respect to the factors influencing the quality and use properties of the product, and the current develop

Jan 1, 1948

By Charles E. Nelson

THIS paper will outline briefly the practices commonly followed in this country for the melting and refining of magnesium and its alloys. The processes used for the various forms of primary magnesium, as jar as there are differences in the physical shape or behavior, will be discussed. The refining of general fine scrap or secondary magnesium was presented in an earlier paper and will be discussed briefly.1 Inasmuch as the use of fluxes is an essential part of all the melting and refining processes, this paper will deal with these in sufficient detail to point out their unique characteristics, in order to make their use more effective. The outline of this discussion will closely follow that of an earlier paper,2 with such changes and additions as seem necessary to bring it up to date. TYPES OF MELTING PRACTICE All melting and refining processes for magnesium and its alloys require the use of fluxes. These fluxes have a magnesium chloride base and other halide salts or oxides are added to give a density or behavior exactly suited to the particular melting practice. The successful handling of magnesium depends upon the proper use of the correct fluxes. There are four general methods of melting, summarized in the following paragraphs and treated in more detail in the section on Melting and Refining. Open-pot Method The open-pot method makes use of No. 230 flux, which provides protection during melting and a molten pool of flux into which the solid magnesium melts. The flux is stirred through the molten metal bath and agglomerates oxide or similar foreign bodies;, on quiet standing, it separates away, leaving the refined metal ball floating in an encircling layer of molten flux. It forms only a thin fluid film over the surface of the molten metal, which may be parted for hand-ladling processes and tends to cover the metal again after the ladle is removed. A very light dusting of the pot surface with fresh flux immediately after the ladle is removed is desirable. The open-pot method is used generally in the following processes: (I) alloying and remelting in the production of ingot, (2) in sand foundries for premelting and to a smaller extent for the production of small castings, (3) in permanent-mold founding for premelting and also direct ladling to castings, (4) for continuous methods of preparing metal in the production of billets or ingots from which wrought products are fabricated, (5) in general scrap recovery. Crucible Process The crucible process makes use of No. 310 flux, which has the property of being thinly fluid at the start, to provide protection and refining qualities, and then drys out or thickens after a time, leaving a protecting crust on the pot surface until the time of casting. At that time it can be readily skimmed off or held back, thus allowing the contents of the crucible to

Jan 1, 1946

By Cyril Wells, Robert F. Mehl

The practical importance of a knowledge of the rates of diffusion of carbon and of alloying elements in steel has often been pointed out.l,13 This importance lies chiefly, though by no means only, in the study of carbufizing and in the study of reactions involved in the eutectoid inversion in steel. The present paper is one of a series in which the rates of diffusion of carbon and of alloying elements in ?-Fe and their mutual effects are measured with precision. The present paper reports the results of measurements of diffusion coefficients D of manganese in ?-Fe over wide ranges of temperature, and concentration, and of the effect of carbon and impurities and of grain size upon these diffusion coefficients.‡ Data on the rate of diffusion of manganese in ?-Fe have been reported by Fry2 and by Paschke and Hauttmann.3 Claussen4 calculated the diffusion coefficient D from Fry's data as 3 X 10-10 sq, cm. per set. at 960º, which will be shown to be incorrect by many orders of magnitude. Paschke and Hauttmann gave a rough value of 9.6 x 10-8 Sq. cm. per set. at 14000. Neither of these workers considered the variation of D with concentration and with temperature, and neither studied the effect of carbon. Method and Materials Method.—The method employed is identical with that used earlier.5 Owing to the volatility of manganese and the consequent loss of manganese from the outer surfaces of the welded diffusion bars, these surfaces were discarded. The diffusion anneals were performed in argon, except One (test 18) in which hydrogen was employed for purposes noted below. The temperatures reported are accurate to about 3" and constant within 1°C; the diffusion times are reported to the nearest half hour. The specimens were furnace-coo1ed after the diffusion ation, at about 2° per min. Layers, usually 0.004 in. thick, parallel to the welded interface, were machined from the specimens after the diffusion anneal and analyzed for manganese to 0.I Per cent Mn; the distances of these layers from the interface was measured to ±0.0002 in. The concentration-penetration curves obtained were analyzed by both the Grube and the Matano solutions.8 The D values calculated by these two methods do not differ appreci000. The Grube solution was used except in tests in which the effect of concentration upon D was greater than so per cent; in such cases the Matano method, which explicitly provides for the variation of D with concentration,' is the more reliable. In general, the number of layers machined from the zones of variable composition were large enough to permit the use of the average layer composition as that of the center of the layer. In 3 of the 3' tests, however, this is not justified, and the D values

Jan 1, 1941

By Cyril Wells, Robert F. Mehl

The practical importance of a knowledge of the rates of diffusion of carbon and of alloying elements in steel has often been pointed out.l,13 This importance lies chiefly, though by no means only, in the study of carbufizing and in the study of reactions involved in the eutectoid inversion in steel. The present paper is one of a series in which the rates of diffusion of carbon and of alloying elements in ?-Fe and their mutual effects are measured with precision. The present paper reports the results of measurements of diffusion coefficients D of manganese in ?-Fe over wide ranges of temperature, and concentration, and of the effect of carbon and impurities and of grain size upon these diffusion coefficients.‡ Data on the rate of diffusion of manganese in ?-Fe have been reported by Fry2 and by Paschke and Hauttmann.3 Claussen4 calculated the diffusion coefficient D from Fry's data as 3 X 10-10 sq, cm. per set. at 960º, which will be shown to be incorrect by many orders of magnitude. Paschke and Hauttmann gave a rough value of 9.6 x 10-8 Sq. cm. per set. at 14000. Neither of these workers considered the variation of D with concentration and with temperature, and neither studied the effect of carbon. Method and Materials Method.—The method employed is identical with that used earlier.5 Owing to the volatility of manganese and the consequent loss of manganese from the outer surfaces of the welded diffusion bars, these surfaces were discarded. The diffusion anneals were performed in argon, except One (test 18) in which hydrogen was employed for purposes noted below. The temperatures reported are accurate to about 3" and constant within 1°C; the diffusion times are reported to the nearest half hour. The specimens were furnace-coo1ed after the diffusion ation, at about 2° per min. Layers, usually 0.004 in. thick, parallel to the welded interface, were machined from the specimens after the diffusion anneal and analyzed for manganese to 0.I Per cent Mn; the distances of these layers from the interface was measured to ±0.0002 in. The concentration-penetration curves obtained were analyzed by both the Grube and the Matano solutions.8 The D values calculated by these two methods do not differ appreci000. The Grube solution was used except in tests in which the effect of concentration upon D was greater than so per cent; in such cases the Matano method, which explicitly provides for the variation of D with concentration,' is the more reliable. In general, the number of layers machined from the zones of variable composition were large enough to permit the use of the average layer composition as that of the center of the layer. In 3 of the 3' tests, however, this is not justified, and the D values

Jan 1, 1941

By Margaret G. Scroger, Luke L. Y. Chang, Bert Phillips

Using the sealed-system technique, isothermal sections at 1000°, 1400°, and 1700°C for the system Co-W-O hare been determined. The equilibrium data were obtained by microscopic and X-ray diffraction examination of samples winch had been equilibrated in pellet form fit sealed capsules and subsequcelly quenched. The only ternary phase in the system is CoWO, which mells congruentlly at approximately 1280°C. At 1000°C, this ternary phase exists in equilihrinm with all the allows and oxide compounds in the hounding binary systems. At 1400°C, liquid forms in thin oxygen-rick region near the CoWO4 composition and only one phase assemblage in the system (W + WO2 + H'5CV7) contains no In order for tungsten to be used to its full potential as a refractory metal. it is necessary that coatings be developed which will preclude oxidation of the metal. It is true that coatings now in use do protect tungsten for short periods at temperatures near 1700 °C. but no coating has been developed which protects adequately at or above this temperature where the use of tungsten is most required. This situation exists despite the great effort in recent years to develop such coatings. and it has become evident that success in this area can be achieved only after a more fundamental knowledge of the thermochemical and therrnophysical propertics of tungsten oxidation and tungsten -metal oxidation is obtained. In our 1aboratories. a project liclrriel. At 1700°C, tungsten is the ouly solid phase which is stctble, and a large range of compositions melt to two liquids, one metallic and one oxidie. The sealed-system method of etjuilibra lion prevents the determination of the partial pressure of oxygen and the total gas pressure orer the condensed phases at equilibrium. This data is not available and can be obtained only by some other method. We can generalize on these unknowns and indicate that both partial pressure of oxygen and total pressure of the gas phase must increase as compositions change from the W-Co binary toward the oxygen apex and as temperatures increase. has been initiated which is directed at providing some of this fundamental information through a study of metal-tungsten-oxygen reactions and equilibria and the properties of any intermediate phases which result. This paper is based on a part of this program in which the system Co-W-O was studied between 1000° and 1700°C. I) RELEVANT INFORMATION FROM THE LITERATURE A) The Notable Lack of High-Temperature Work on Metal-Tungsten-Oxygen Systems. It should be pointed out that there has been no published report (of which we are aware) which deals with the study of a metal-metal-oxygen system at 1700°C. Also, there has been no report on a complete metal-luugsten-oxgen system at any temperature. As a matter of fact. before this program started. The

Jan 1, 1965

By R. B. Hoy, Stanley J. LeFond, K. Reckling

Reported world production of natural diamonds approximates 40,000,000 carats a year (1980). The Republic of Zaire is the leading producer, with an output which is primarily industrial rather than gem grade. The USSR ranks second, the Republic of South Africa third, and Botswana, fourth. Diamonds are also mined in South-West Africa (Namibia), Angola, Ghana, Sierra Leone, and other African countries. In the western hemisphere, Brazil and Venezuela are the principal producers (Fig. 1). A very small output of diamonds is mined today it India, which was the first source of commercial production. In the US, efforts at commercial diamond mining have been confined to a small area near Murfreesboro, AR. The first diamond was found in a kimberlite pipe there in 1906. Small-scale trial mining has not, however, proved economical. Since diamonds were first discovered over 2,000 years ago, only about 260 tons have been mined. In order to obtain I g (5 carats) of diamonds, it is necessary to remove and process approximately 25 tons of rock. Recovering this small percentage involves a combination of highly developed techniques in mining, quarrying, and earth-moving, and extremely sophisticated recovery processes. End Uses Diamonds are used for two unrelated end uses; gem diamonds are jewels of great beauty while industrial diamonds are essential materials of modern industry. Although imitation stones are substituted for the gem diamond, none of these matches its properties sufficiently well to offer real competition. Synthetic industrial diamonds are now of a quality and size that permit them to be substituted for natural diamond in numerous industrial applications. For example, synthetic diamonds are available today in sizes up to 100 stones per carat (14/16 US mesh size). In addition, polycrystalline synthetic diamond inserts, such as De Beers Syndite®, General Electric's Compax® and Stratapax® and Megadiamond's Megapax® have replaced natural diamond in turning tools, mining and oil drilling bits and dressing tool applications. Gem Diamonds A diamond is a natural prism. It has the ability to bounce light rays (reflection), to bend them (refraction), and to break them into all colors of the rainbow (dispersion). This ability to modify light gives the diamond three characteristics for providing beauty. First is brilliance, the reflection of light back to the eye. Second is fire, dispersion of light into the colors of the spectrum. Third is scintillation, the "twinkling" that occurs when the diamond is moved (Bauer, 1969). The skill of the diamond cutter is required to unlock the brilliant, fiery beauty of a gem diamond (Fisher, 1966). Diamond-cutting skills have gradually developed over the centuries. The first cutters, in India, learned how to grind one rough diamond against another to remove their "skins" and to give them various shapes. This revealed some fire and beauty, but little compared to that of the diamonds that are cut today.

Jan 1, 1983

By J. E. Ostberg, G. Phragmen, A. Hultgren, S. Wohlfahrt

Detailed study was made of a number of rimming ingots, both low and high carbon, and especially upon effects of superimposed air pressure. Requirement to suppress core bubbles is between 10 and 15 atm; at 6.5 atm freezing was in semikilled manner and at 3 atm, steel was of rising type. Probable mechanism of freezing under various conditions is discussed. AN earlier paper' reported an investigation made by a committee for studying rimming steel ingots appointed by Jernkontorets in Stockholm. The present paper is the outcome of some further work done by the same committee. Since the characteristics of ordinary rimming steel are connected closely .with the amount of gas liberated during freezing and since this amount of gas is governed by the pressure, it was considered of interest to ascertain in what manner and to what extent definite pressures applied to the top of the liquid steel in the mold would affect the solidification process and the consequent structure of a rimming steel of ordinary composition. The experiments were made at the Domnarfvets Steel Works. The steel was made according to normal practice in a 4-ton Rennerfelt electric furnace. Ferromanganese was added in the furnace; no aluminum was added, with one exception. Analyses of the four heats are given in Table I. The top-poured ingots measured about 12 in. sq x 48 in. and weighed about 1300 lb. One or two ingots of each heat were allowed to solidify under pressure, using a special device for admitting compressed air to the upper closed part of the mold, as shown in Fig. 1. A heavy plate sealed with asbestos was bolted to the top of the mold. The plate had a tapered aperture for pouring. Immediately after pouring the hole was closed by a wedged plug, and compressed air was admitted through a hole in the plug. Because of some delay in applying the plug, full pressure was not reached immediately. The pressure was adjusted to the desired value as indicated by a manometer. In order that the interior of the ingot might have the benefit of the pressure, the freezing of the top crust was delayed by a refractory lining applied to the top part of the mold, Fig. 1. Ingots were also cast from each heat without applied pressure, and with and without refractory lining at the top. Axial sections of ingots were cut either of the whole ingot or of some part of it of special interest; sections were polished and usually etched.' To facilitate description of structures the following terms may be used for different types of ingots solidified under gas evolution: 1. Box-hat or boot-leg ingot: Abundant gas evolution during casting and during rimming; no rim holes. 2. Normal rimming ingot: Lively gas evolution during rimming; usually rim holes in lowest part of

Jan 1, 1952

By L. G. Schulz, P. Spiegler

The electrical resistivity and the temperature coefficient of resistivity were measured with a potentiometric method using pure mercury as a reference material. Measurements were made nea,v roorn temperature. A detailed study was made of Hg,TI, near its melting temperature. THE work to be described was originally undertaken to provide the necessary data for interpreting the results of some optical experiments,' but because of the growing importance of liquid metals,273 it appeared that the results of the resistivity measurements should be published separately. For convenience the alloys selected were those which are liquid at room temperature. Special consideration was given to the Hg-T1 alloy closely corresponding to Hg,Tl, because recent X-ray diffraction results of Smallman and Frost seemed to show that the solid structure may persist to some extent into the 1iquid. EXPERIMENTAL PROCEDURE A potentiometric method was employed in which the resistivity of mercury was used as a reference. The essential features of the samples are shown in Fig. 1. A capillary tube CT with a bore of approximately 1.5 mm was fitted into two end cups, T, which were made of Teflon. A pair of current electrodes CE were immersed into the excess liquid metal which partly filled the end cups. The potential electrodes PE were inserted into CT through short pieces N of a no. 18 hypodermic needle held in place with Saureisen cement SC. As shown, the lower ends of the PE7s were reduced in diameter to 0.25 mm to minimize the distortion of the liquid metal cross section. Several methods were used to insert an alloy into the sample, but the usual one with mercury alloys was to fill the sample container with a weighed quantity of pure mercury* and then add weighed the sample tube in a vacuum. Because of rapid corrosion, samples containing gallium were of necessity prepared in a vacuum. To obtain the specific resistivity of an alloy the resistance of the sample containing the alloy was measured and compared with the resistance when the container was filled with mercury. Resistances were measured in the temperature range of 20" to 60°C to obtain the temperature coefficient of resistance. The electrical measurements were made by connecting the sample in series with the standard one-ohm resistance, and the potential drop measured alternately over the sample and the standard resistance. To correct for stray thermoelectric effects provision was made for reversing the direction of the current, and the true potential drop was taken to be the average of that obtained for the two directions of current flow. Various materials were used for the electrodes, the most uniform results being obtained with nickel. EXPERIMENTAL RESULTS The numerical results are presented graphically in Figs. 2 and 3 and in tabular form in Tables I and 11. Following are remarks on results of individual alloys. 1) Hg-In—This was the first alloy studied, and

Jan 1, 1960

By J.B. Pullen

The United Verde mine is in the north central part of Arizona, on the northeasterly slope of the Black Hills, near the town of Jerome. Ore was first discovered in the district about 1875, and the first mining claims were located by M. A. Ruff-ner and associates in 1877. In 1888 the late Scnator William A. Clark secured control of the property and under his ownership it developed into one of the country's most important copper producers. The property was sold to the Phelps Dodge Corporation in 1935, and since then has been under this Corporation's management. Except for shutdowns caused by general world-market conditions, production has been continuous from 1890 to date. Geology The mineralized zone ranges in area from approximately 12 acres to less than 5 acres. All mineralization occurs in the pre--Cam-brian intrusives. The first intrusion, according to geologic records, was the quartz porphyry, which later was intruded by augite diorite. Following the diorite intrusion through a series of intrusions of lesser magnitude, a pipelike mass of massive sulphide, quartz and rock was formed. The diorite forms the hanging wall of this mass, and the porphyry the footwall. Between the footwall and the sulphide a band of chlorite schist was formed, probably owing to metamorphic conditions. Commercial ore occurs along the contact of the schist and sulphide extending into the sulphide, sometimes entirely through the schist, and fingering out into the porphyry. The ore deposit was formed by replacement similar to deposits formed in limestone areas. Faulting and deformation occurred in pre-Cambrian times and again in the Tertiary period, removing approximately 2000 ft. from the top of the main United Verde ore body, forming the United Verde Extension ore body, the only other major ore body in the district. Major development work has shown that the sulphide mass extends to the 3300-it. level, and diamond drilling below this level has indicated that the mass might extend below the 3700-ft. level, but in a diminished quantity. While many copper minerals exist in the mine, the chief commercial mineral is chalcopyrite. Aplan and vertical section of the mineralized zone showing the principal geological eatures is shown in Figs. I and 2. General Description and Physical Condition or Mine After over 50 years of active production, ore still exists on almost every level of the mine. This condition is due to many causes —-mine fires, which broke out as early as 1894, caused the abandonment of certain areas; subsidence and ground movements retarded the cleaning up of others. Furthermore, in the early days there was such an abundance of ore that when mining became dificult it was a simple matter to replace the production by going to a deeper level. Several attempts were made to recover the ore in the fire zone, both by glory-holing

Jan 1, 1943

By J. B. Pullen

The United Verde mine is in the north central part of Arizona, on the northeasterly slope of the Black Hills, near the town of Jerome. Ore was first discovered in the district about 1875, and the first mining claims were located by M. A. Ruff-ner and associates in 1877. In 1888 the late Scnator William A. Clark secured control of the property and under his ownership it developed into one of the country's most important copper producers. The property was sold to the Phelps Dodge Corporation in 1935, and since then has been under this Corporation's management. Except for shutdowns caused by general world-market conditions, production has been continuous from 1890 to date. Geology The mineralized zone ranges in area from approximately 12 acres to less than 5 acres. All mineralization occurs in the pre--Cam-brian intrusives. The first intrusion, according to geologic records, was the quartz porphyry, which later was intruded by augite diorite. Following the diorite intrusion through a series of intrusions of lesser magnitude, a pipelike mass of massive sulphide, quartz and rock was formed. The diorite forms the hanging wall of this mass, and the porphyry the footwall. Between the footwall and the sulphide a band of chlorite schist was formed, probably owing to metamorphic conditions. Commercial ore occurs along the contact of the schist and sulphide extending into the sulphide, sometimes entirely through the schist, and fingering out into the porphyry. The ore deposit was formed by replacement similar to deposits formed in limestone areas. Faulting and deformation occurred in pre-Cambrian times and again in the Tertiary period, removing approximately 2000 ft. from the top of the main United Verde ore body, forming the United Verde Extension ore body, the only other major ore body in the district. Major development work has shown that the sulphide mass extends to the 3300-it. level, and diamond drilling below this level has indicated that the mass might extend below the 3700-ft. level, but in a diminished quantity. While many copper minerals exist in the mine, the chief commercial mineral is chalcopyrite. Aplan and vertical section of the mineralized zone showing the principal geological eatures is shown in Figs. I and 2. General Description and Physical Condition or Mine After over 50 years of active production, ore still exists on almost every level of the mine. This condition is due to many causes —-mine fires, which broke out as early as 1894, caused the abandonment of certain areas; subsidence and ground movements retarded the cleaning up of others. Furthermore, in the early days there was such an abundance of ore that when mining became dificult it was a simple matter to replace the production by going to a deeper level. Several attempts were made to recover the ore in the fire zone, both by glory-holing

Jan 1, 1943