Search Documents

By W. F. Holbrook

In a previous paper1 a method for the measurement of the comparative desulphurizing power of slags was described and data were presented covering the range of likely slags containing up to 10 per cent MgO. In the present work the range is extended to include slags containing up to 20 per cent MgO, and the effect of temperature on 5 per cent and 15 per cent MgO slags over the range 1475' to 1525' C. is included. The method used was that described in the previous paper except that some of the temperature measurements were made with a noble-metal thermocouple instead of a tungsten-graphite thermocouple. Twelve-gram charges of 0.8 per cent sulphur-metal and 5-gram charges of slag were subjected to heating for 30 min. at a prescribed temperature. The charges were analyzed for sulphur content. For purposes of comparison, desulphurizing power is defined as the ratio of the percentage of sulphur found in the slag to that found in the metal. Six slag and metal charges were made coincidentally in 5/8in. holes in a section of an electrode graphite rod. One slag and metal charge was used as a control by means of which adjustment in the desulphurization value could be made for small variations in temperature and other factors. For convenient presentation of the data, the slags are arranged in groups in each of which one of the four main slag components is constant. Thus, the 15 per cent MgO slags are presented separately from those containing 20 per cent MgO. Slags with Magnesium Oxide Constant 15 Per cent Mg0.—The data on slags containing 15 per cent MgO cover a composition range of 24 to 50 per cent SiO2, 5 to 27 per cent A1203 and 24 to 53 per cent CaO. Variation in composition has been in steps of 2 per cent over much of the area. Because the change in desulphurization power is generally gradual with gradual change in composition, certain sections have been covered in steps of 4 per cent and even

Jan 1, 1938

By W. F. Holbrook

In a previous paper1 a method for the measurement of the comparative desulphurizing power of slags was described and data were presented covering the range of likely slags containing up to 10 per cent MgO. In the present work the range is extended to include slags containing up to 20 per cent MgO, and the effect of temperature on 5 per cent and 15 per cent MgO slags over the range 1475' to 1525' C. is included. The method used was that described in the previous paper except that some of the temperature measurements were made with a noble-metal thermocouple instead of a tungsten-graphite thermocouple. Twelve-gram charges of 0.8 per cent sulphur-metal and 5-gram charges of slag were subjected to heating for 30 min. at a prescribed temperature. The charges were analyzed for sulphur content. For purposes of comparison, desulphurizing power is defined as the ratio of the percentage of sulphur found in the slag to that found in the metal. Six slag and metal charges were made coincidentally in 5/8in. holes in a section of an electrode graphite rod. One slag and metal charge was used as a control by means of which adjustment in the desulphurization value could be made for small variations in temperature and other factors. For convenient presentation of the data, the slags are arranged in groups in each of which one of the four main slag components is constant. Thus, the 15 per cent MgO slags are presented separately from those containing 20 per cent MgO. Slags with Magnesium Oxide Constant 15 Per cent Mg0.—The data on slags containing 15 per cent MgO cover a composition range of 24 to 50 per cent SiO2, 5 to 27 per cent A1203 and 24 to 53 per cent CaO. Variation in composition has been in steps of 2 per cent over much of the area. Because the change in desulphurization power is generally gradual with gradual change in composition, certain sections have been covered in steps of 4 per cent and even

Jan 1, 1938

By Thomas A. Hendricks

The object of this paper is to give a brief description of the coals in the different districts of Arkansas and Oklahoma, their present commercial classification, and the need for a scientific classification that shall be more nearly in accord with their physical and chemical properties and shall place them in their proper position in a general scheme of classification. The paper is based on two seasons of field work in the Oklahoma coal field in 1930 and 1931 and on several weeks spent in visiting most of the operating mines in Arkansas in the same years. Most of the productive districts of the Arkansas-Oklahoma coal field lie in an east-west trending belt immediately north of the Ouachita Mountains, but the northwestern districts in Oklahoma trend northward toward Kansas. With the exception of the Muskogee district, where very little coal has been mined, the coal beds of the last-mentioned districts are all younger than those of the districts in the east-west trending belt. Description of the Coal by Districts Lehigh District, Oklahoma (5).1—In the Lehigh district mining has been extensive, but only three or four mines are operating at the present time. Two coal beds of workable thickness, Atoka and Lehigh, are known in this field. The greater part of the mining has been in the Lehigh, or younger bed, and all analyses available for the field have been of that coal. The Lehigh coal is very tough and blocky, the moisture and ash contents are fairly high, 6.5 and 10.7 per cent respectively, the volatile content is 39.5 per cent, fixed carbon 43.4 per cent, B.t.u. value 11,525, and the fuel ratio 1.1 (average 15 analyses). So far as the writer has been able to ascertain, laboratory attempts to coke this coal have been unsuccessful and no attempt has been made to produce coke commercially. Tulsa District, Oklahoma (l).—All commercial mining in the Tulsa district has been by stripping from the Dawson bed, and production has never been very great. The coal is blocky, contains 6.5 per cent moisture, 36.8 per cent volatile matter, 48.4 per cent fixed carbon, and 8.3 per cent

Jan 1, 1932

By Byron W. Cheever

While engaged in experimenting with the usual methods for estimating phosphorus in iron and steel, it occurred to me that potassium chlorate might be used to oxidize the carbon, and thus avoid the tedious and vexatious evaporations necessary for successfully carrying out the usual methods. After many trials, the following plan was adopted : Take, for analysis, of Bessemer or other low-carbon steels, from 3 to 5 grammes; of crucible steel, 10 grammes; of pig-iron, 1 to 5 grammes, according to the percentage of phosphorus supposed to be present. Of iron, high in phosphorus (1 per cent.), take 1 gramme. Place in a No. 4 evaporating dish the amount of iron or steel decided upon, cover with a funnel which will just fit inside the dish, and then add gradually HNO3, (1.20 specific gravity), using 12 C.C. of acid for each gramme of steel or iron taken. (A larger quantity of acid will be required for small samples.) When the full amount of acid has been added, and the violent action has ceased, place the evaporating dish on a sand-bath, add 10 C.C. HNO3, (1.40 specific gravity), and boil till the bulk of the solution is reduced about onehalf. Then add 10 C.C. HNO3, (1.40 specific gravity), continue the boiling, and add from time to time, during the next 15 minutes, small portions of pulverized KCIO3, till about 2 grammes have been added. (If the solution shows signs of going dry, more strong acid must be added.) This will precipitate the manganese, with some iron. Sometimes it happens that the manganese does not come down readily, and more KCIO3, or further concentration, or both, will be required. The process is not complete till the manganese is precipitated, which may be known by the appearance of a dark, mirror-like deposit on the dish, at the edge of the solution. Boil the solution 5 minutes after the last addition of KCIO3, and then add cautiously (to prevent sudden explosions) 5 C.C. strong HCl. This will dissolve the precipitated manganese and iron. Continue the boiling till the chlorine is all expelled, adding from

Jan 1, 1885

By R. E. Cech

Particles -3 to 30 µ diam of a 29.5 pet Ni, 70.5 pet Fe alloy after being melted and solidified while falling through a hydrogen atmosphere were found to contain a distortion-free body-centered-cubic phase. In most particles, the amount of body-centered-cubic phase approaches or equals 100 pet. It was shown by a series of experiments that this phase forms directly from the liquid. It is pointed out that a mechanism previously suggested in recent papers on the theory of the liquid-solid transformation can account for the solidification of body-centered-cubic phase in a temperature range where face-centered-cubic is the stable phase. IN the course of an operation to produce powders for a study of the martensitic transformation in Fe-Ni alloys, an unexpected phenomenon was observed. Powders of a 29.5 pet Ni alloy, which has a subzero M, temperature, were found to contain considerable amounts of a body-centered-cubic phase at room temperature. The experiments to be described were designed to elucidate the mode of formation of this unexpected phase. Experiments and Discussion An alloy containing 29.5 wt pet Ni, balance iron, was vacuum melted from high purity electrolytic iron and carbonyl nickel shot and solidified in the crucible. The metal was converted to oxide, ground to 100 pet <37µ, pressed to a cake, and homogenized 20 hr at 1350°C. To insure homogeneity the grinding, pressing, and homogenizing heat treatment was repeated a second time. The oxide was then ground to 100 pct <37µ and hydrogen reduced at 500°C. The reduced powder was given a spheroidizing treatment to produce spherical cast particles. The treatment consisted of dispersing the particles in hydrogen and allowing them to drop through a vertical hydrogen furnace set to a temperature higher than the liquidus of the alloy. This operation, commonly known as shotting, has been described more fully elsewhere.&apos; The powder produced by this method was found to contain approximately equal parts of body-centered-cubic and face-centered-cubic phases. A magnetic separation technique, previously described,&apos; was applied, and it was found that particles were either completely face-centered-cubic or nearly completely body-centered-cubic. The microstruc-

Jan 1, 1957

By W. M. Dressel, A. Visnapuu

The Bureau of Mines, U.S. Department of the Interior, has upgraded high-iron domestic chromite concentrate to high-chromium concentrate by a laboratory carbonyl process. The chromite concentrate product has a chromium-to-iron ratio in excess of 3:l compared with the starting concentrate ratio of 1.6:1. The high-iron chromite was first reduced to convert the iron oxides to the metal, and then treated with carbon monoxide at elevated pressures and low temperatures to convert the metallic iron fraction to iron pentacarbonyl. Carbonylation was accelerated by the addition of hydrogen sulfide in small quantities. A constant flow of carbon monoxide swept the iron pentacarbonyl formed in the reactor out through a pressure-reducing valve. The mixture of carbon monoxide and iron pentacarbonyl at atmospheric pressure was then passed through a heated section to decompose the iron pentacarbonyl to carbon monoxide and iron, whereupon the latter plated out on the heated surface. Carbon monoxide pressure, temperature, and promoter trends for enhanced carbonylation are presented.

Jan 1, 1984

By Robert C. Mackenzie

EXAMINATION by the differential thermal analysis technique of a large number of samples of soil and other clays from various parts of the world has demonstrated that the occurrence of cold-precipitated hydrated ferric oxide (the identification of which in soil clays has previously been reported5) is not confined to any limited locality; e.g., it has been found in varying amounts in clays from Britain, France, South Africa, and Mexico. The conditions necessary for its formation have not yet been elucidated in spite of the number of samples examined, and, since this mineral is so easily prepared in the laboratory, it has been considered that a study of its constitu¬tion and of the conditions under which it could be prepared might. lead to a better understanding of the factors involved. These experiments form the subject of this short paper, and while they do not supply a definite answer to the mode of formation of this mineral in nature, they may, it is hoped, add something to our knowledge in this direction. EXPERIMENTAL WORK Materials Employed The a-Fe2O3.H2O (goethite) and B-Fe2O3.H2O (Weiser and Milligan") were obtained from the Department of Geology, University of Aberdeen, and Rothamsted Experimental Station, respectively. The beta material had been prepared by the method described by Fernelius.1 y-Fe2O3.H2O (lepidocrocite) was prepared at the Macaulay Institute for Soil Research by the method of van Schuylenborgh.6 The method employed for preparation of the cold-precipitated hydrated ferric oxide* was as follows: 1: 1 NH4OH was added (moderately fast with rapid stirring) to a solution of 5 grams FeC13.6H2O in 250 ml distilled water at room temperature (ca. 15°C) until red litmus turned blue, and then 2 to 3 drops in excess. The resultant precipitate was filtered off on a Buchner funnel and washed free from Cl- with distilled water. Previous experiments having shown that drying over P2O5 at room temperature or drying at 105°C in the oven did not significantly affect the thermogram,5 samples were nor-

Jan 1, 1952

By C. O. Burgess, A. B. Kinzel

Although vanadium is an important constituent of almost every brand of high-speed steel manufactured today, little is known as to its role in this series of alloys. The now standard 18 per cent tungsten and 4 per cent chromium constituents were the result of developments and improvements before 1903. In that year, vanadium was added to the steel by Dr. J. A. Mathews. This proved to be an outstanding contribution, so that the standard high-speed steel of today is generally referred to as the 18-4-1 type—18 per cent W, 4 per cent Cr and 1 per cent V. Various modifications have been attempted since then, but with the exception of the introduction of cobalt, no striking improvements have occurred. Vanadium has been increased to 2 per cent in many of the common brands, and at least one brand contains 5 per cent V in addition to the usual tungsten and chromium. The carbon has been gradually increased so that it is not uncommon to find 0.80 per cent in the standard grade, although the carbon in the 5 per cent vanadium steel mentioned above is approximately 1 per cent, and even 1.2 per cent has been made experimentally. The role of vanadium has never been well understood, and although vanadium has been increased to 2.5 and even 5 per cent in certain high speed steels, it has not been generally established that the higher vanadium contents result in superior cutting properties. However, in all of the investigations, of which the writers are aware, the interrelation of the vanadium and carbon contents was not considered as a prime factor. The carbon content was held at 1.2 per cent or less—generally at the usual 0.65 to 0.75 per cent. Theoretical Aspects Although the role of vanadium is not understood, there are theoretical considerations which indicate definite reasons for the improved cutting effciency due to vanadium. Refinement of the secondary grain is one distinct possibility. The well-known action of vanadium in limiting grain size might well be expected to operate in high-speed steels, and even though its action were not evident in the parent austenite grain.

Jan 1, 1932

By Albert F. Schneider

The peculiar conditions under which lead and silver ores are now smelted in Salt Lake Valley, Utah, render it advantageous to make slags that are siliceous and carry a high percentage of lime. The ores treated come from Utah, Idaho, Montana, and Nevada; nine-tenths coming from Utah. These ores are siliceous, and contain but little fluxing material; the iron present scarcely sufficing for the sulphur and arsenic. Formerly ores high in iron were furnished from Cottonwood Canons, but this supply is meagre. The ores from Idaho, Montana, and Nevada are high grade galenas, more or less impure. They generally require a large amount of iron for the sulphur, arsenic, and antimony. In the winter and spring of 1880—&apos;81, we were treating at the Germania Works principally Bingham Canon lead ores and silver ores from Tintic. The former contained 15 to 30 per cent. silica, and only 4 to 5 per cent. iron (generally as iron pyrites); they ranged high in lead and low in silver, and carried more or less alumina; the lead was present chiefly as carbonate. The silver ores from Tintic contained sulphides, and ran as high as 80 per cent. silica. We had been running on a slag approximating 40 per cent. FeO, 20 per cent. CaO, 10 per cent. other bases, and 30 per cent. SiO2, which had heretofore been very satisfactory; but with the class of ores then coming in it was of the utmost advantage to use less iron and more lime, especially as the iron ore (50-55 per cent. iron and 5-7 per cent. silica) cost four times as much as the limestone (50-55 per cent. lime, 3-5 per cent. silica). The large amount of alumina in the slag influenced them for the worse; the addition of lime to the charge helped them, and after many experiments regarding the proportion of FeO, CaO, and SiO2, a slag approximating 35 per cent. FeO, 25 per cent. CaO, 5 per cent. other bases, and 35 per cent. SiO2 seemed to answer

Jan 1, 1883

By J. Ostachowicz, B. Holynska, M. Lankosz

The paper presents an analyzer and the method for the continuous determination of weight percentage of ore grains with diameter smaller than 75 µm in mineral slurries. The method is based upon the measurement of characteristic x-rays of copper excited by primary radiation of two different energies 16.5 keV and 60 keV from Pu238 and Am241 sources respectively. Additionally the backscattered primary radiation is measured in order to correct the variations of the solids content in the slurry. Since the particle size distribution of slurry can be described by the Rosin-Rammler formula, some calculations have been carried out in order to evaluate the influence of distribution parameters upon the results of the measurements of weight percentage U75 of particles smaller than 75 µm. The influence of solids content and of the copper concentration variation on the results has been also evaluated.1 It resulted from the calculations that the ratio rl/rz, where rl and r2 are the relative intensities of copper characteristic x-rays excited with 16.5 keV and 60 keV photons respectively does not depend on the copper content within the range 1 % to 4% of copper and is slightly dependent on the solids weight fraction and its chemical composition. The change of the dispersion parameter of the Rosin- Rammler distribution from 0.5 to 0.9 results in a change of value of U75 of approximately 3.0%. The results of calculations have been confirmed by the results of laboratory experiments. Therefore, a prototype of industrial analyzer for continuous determination of weight percentage of particles smaller than 75 µm has been designed and made. Its schematic drawing is shown in [Fig. 1]. Slurry is flowing down through steel flow-cell of the length equal to approx. 2 m. In the center, two XRF measuring heads (1) and (2) are located. Each of the heads comprises a rigid waterproof cover (3) with the mylar window (4), in which a proportional counter of resolution 15% for 6.4 keV is mounted with a preamplifier (5). The low- energy isotope source (6) is centrally located above the detector

Jan 1, 1980

By E. M. Norris

In the summer of 1917 it was decided to fireproof the main Tramway hoisting shaft of the Anaconda Copper Mining Co. at Butte, Mont. The shaft has three hoisting compartments and one pump compartment; it is timbered with 12 by 12-in. (30.5 by 30.5-cm.) fir timber, and is 2475 ft. (754 m.) deep. Subsidence and displacement of the surrounding country rock had produced exceedingly heavy ground, and had carried the shaft out of line, in several places, by as much as 2 ft. (0.6 m.) displacement. Constant repairing and realigning of the timbers had been necessary in order to maintain clearance for the cages. The most feasible method of fireproofing, therefore, seemed to be to cover the timbers with a coat of concrete applied with the cement gun. The cement gun, which is operated by compressed air at ordinary mine pressures, feeds a mixture of sand and cement through a hose to a nozzle having a water connection. The mortar in fluid form is thus sprayed upon the prepared surface in thin layers, which can be built up to any desired thickness. The cement gun can be set up at any convenient point; satisfactory results have been obtained with the nozzle a distance of 500 ft. (152 m.) from the gun. The shaft was thoroughly overhauled and the timbers put in the best possible state of repair. Between the 1000 and the 1400 levels, much loose ground lay against the shaft timbers on the north side; this was breast-boarded back and a 30-in. (76-cm.) reinforced-concrete retaining wall was erected, leaving a space of 12 in. (30.5 cm.) outside the shaft timbers to allow for future movements of the ground. For convenience in handling men and materials, it was arranged to concrete the auxiliary hoisting-cage compartment and the pump compartment first, using the cages of the main hoist to serve the cementing crews. The auxiliary cage was then available while the remainder of the shaft was being concreted. A tight partition of 2-in. (5.08-cm.) plank was erected between the auxiliary and the adjoining hoisting compartments, for better protection of men riding on the cages. The application of concrete made this

Jan 1, 1920

By Gerald C. Dohm

INTRODUCTION After a mining company has discovered a mineral deposit, the problem is then how to mine and process that deposit the best way. The principal problem facing managers or engineers who must decide on mine plant size, equipment selection, and long-range scheduling is how one can optimize a property not only in terms of efficiency but also as to project duration. Mine opti¬mization is dependent upon the interaction of con¬tributing parameters which leads to maximizing the net present value (NPV) Realistic mine planning is the key, to the analysis. The process is to be used when evaluating undeveloped properties or when a complete revamping of existing facilities is scheduled The proc¬ess is not intended for detailed mine design but rather for property evaluation and feasibility studies. The derivation of the various input parameters will only be discussed to the point where a meaningful correlation can be made with the overall analysis. The interrelationship of the parameters will be the central point because most company guidelines and financial analysts have their own standards when deriving the various inputs. Assume that the data is totally acceptable and pro¬vides at least the following categories of information and guidelines- (1) mineral and waste inventory; (2) geologic, hydrologic, and geotechnical criteria; (3) topographic layout including property boundaries; (4) metallurgical flowsheet, recovery and design criteria; (5) access, water, power, and environmental base-line study; and (6) financial constraints (minimum rate of return, payback period, etc).

Jan 1, 1979

By Albert Sauveur

My first paper dealing with the theories of the hardening of steel by rapid cooling was published in the Transactions of this Institute in 1896— 30 years ago-under the title "The Microstructure of Steel and the Current Theories of Hardening," hence, also, the title of the present paper. It was extensively discussed and was, I believe, one of the starting points of many subsequent papers and discussions of the same subject, dis-cusssions which at times became almost violent and which led to the formation of different schools such as the "Carbonists" and the "Allo-tropists." Some of the older members of the Institute, who took part in the debate or who were interested observers, will, I am sure, have kept a vivid remembrance of it. The controversy gradually quieted down, apparently for lack of ammunition, without any side acknowledging defeat. Recently, however, interest in it ha been revived through the claims of some that these vexed questions had at last been solved. In an effort to ascertain if possible the prevailing view of those best qualified to express an opinion a questionnaire was submitted to the following gentlemen: J. 0. Arnold Sir Robert Hadfield Edgar C. Bain W. H. Hatfield Carl Benedicks Samuel L. Hoyt N. Belaiew Kotaro Honda H. M. Boylston Zay Jeffries Harry Brearley H. Le Chatelier G. K. Burgess H. H. Lester William Campbell Francis F. Lucas H. C. H. Carpenter John A. Mathews Pierre Chevenard A. McCance P. Dejean Albert Portevin C. A. Edwards Walter Rosenhain F. Giolliti Bradley Stoughton G. Grenet F. C. Thompson Leon Guillet

Jan 1, 1926

By Thomas Haight Leggett

I.—The Deep-Level Shafts. The gold-deposits of the Witwatersrand (Anglice, " White Waters&apos; Range ") are, as is well-known, more or less parallel and tilted sedimentary beds of quartz-pebble conglomerate impregnated with gold. These beds, however, are locally called "reefs"—a term equivalent in signification to the American "ledge"—and, like the latter, usually applied to lodes, though covering in practical usage all deposits of tabular form. The first developments of the reefs of the Rand were naturally made along their outcrops. Since the mining law of the Transvaal does not confer upon locators the "extralateral right," the property of each locator upon the outcrop or apex ends with the vertical planes drawn through the boundaries of the claim. Consequently those portions of the reefs which lie "on the dip," beyond these boundaries, are separately acquired by locating new surface-claims, and are usually to be mined only by means of vertical shafts, reaching the reefs at considerable depths. The term "deep-level properties " is given to such claims on the dip, and the " deep-level shafts " are the vertical shafts sunk in the hanging-wall of the Witwatersrand reefs, in contradistinction to the incline-shafts almost universally employed on the outcrop-properties. Number and Distribution.—The accompanying diagram, Plate I., shows the number and depth of these deeplevel shafts, completed or under process of sinking, up to January 1, 1900. A number of shafts already located upon new deep-level properties, but upon which no work has yet been done, are not included in this diagram.* Vertical shafts sunk upon outcrop-

Jan 1, 1901

By Joseph W. Roe

MANY questions arising in the work of the mining engineer may be solved quickly and with sufficient accuracy by the methods of descriptive geometry; but, unfortunately, this subject is more often considered from a mathematical view-point than as an effective tool. for solving practical problems. Some of the principles involved are merged into the ordinary operations of mechanical drawing, and are used unconsciously by the engineer in his every-day work. The rest are stowed away on the book-shelf with his forgotten or rarely-used college text-books. One reason for this condition of "innocuous desuetude " may lie in the unfortunate and often cumbersome notation which it has been found necessary to introduce. If some of these principles can be recalled to the engineer&apos;s attention in terms of every-day use they may prove of practical bearing. Recently, in talking with several mining engineers, I used some of the drawing-room methods of a machine-designer, to the evident surprise of those around me. These men were perfectly familiar with the methods, but their application to mining-work had not occurred to them. At their suggestion the present paper is offered, not in any way as a treatise, but merely to suggest a certain point of view, in hope that it may lead others far more familiar with mining-problems to pursue the subject further. I. To FIND THE STRIKE. As the simplest and most fundamental problem, let it be required to find the strike of a vein when the location and elevation of three points on the outcrop are known. It will be assumed for the present that the vein is a plane.

Mar 1, 1910

By B. Silliman

The regions of New Mexico referred to are in Socorro, Grant, and Dona Ana counties, and a portion of Lincoln County, embracing in the aggregate a very large area, of most of which our knowledge is as yet very fragmentary and superficial. It is only very recently that large portions of this region have been accessible. It has been full of danger from hostile bands of wandering Apaches, whose murderous raids have slain many adventurous miners and seriously prevented developments. But this evil has now been largely abated, and in many of the mining camp of this region there is no longer any danger from this cause. SOCORRO MINES. About three and a half miles back of the old Mexican town of Socorro, on the Rio Grande, chief town of the County of Socorro, are two or more large veins of heavy spar, cutting across the fat* of Socorro Mountain in a northeast and southwest direction, and dip ping at an angle of about forty degrees into the body of the mountain. These veins are in rhyolite, and, so far as could be seen in openings on the Torrence Mine, which I examined, are without any clay parting or selvage. The average thickness of the Torrence rein may be about five feet, the thickness varying from pne or two feet to thirteen feet. Upon the cleavage planes of the heavy spar occurs, in visible patches, of a waxy Iustre and gray color, silver chloride, which gives value to the vein, from a few ounces up to one hundred and twenty ounces to the ton, averaging about forty ounces, as I

Jan 1, 1882

By Frederic P. Dewey

At the Seventh International Congress of Applied Chemistry I presented a paper,&apos; The Assay and Valuation of Gold-Bullion, in which are briefly mentioned a few illustrations of different methods of sampling gold-bullion, particularly cyanide-bars. Since then I have carried on an extensive investigation upon the sampling of gold-bullion in relation to its effects upon the assay-results, in connection with the statement of accounts between the smaller assay-offices of the United States which purchase gold-bullion and the mints where the purchases are re-deposited. Under the name of gold-bullion are included metals of widely different composition. We may have practically pure metal, 999.75 fine or even more in gold; alloys of .gold and silver with only trifling amounts of base metal; alloys of gold and copper with trifling amounts of other metals; ternary alloys of gold, silver, and copper, or gold, silver, and lead; and most complex alloys of from five to eight or more constituents of ordinary occurrence, besides some of the rarer metals occasi&apos;onally. In any one or all of these classes we may have one or more of the metalloids, which may add to our difficulties. Of course, with metal 999.75 fine in gold there is only slight opportunity for different samples to differ in fineness, but on such fine metal we expect the assays to agree very closely, and the sampling must be done with the utmost care. When possible, dip- or granulation-samples of the molten metal should be taken; but when it is necessary to sample bars, the chief point to guard against is surface-dirt.

Jan 1, 1913

By David W. Brunton

The list of our past-Presidents comprises the names of many who, in their official addresses, have sketched the current progress of the arts and professions with which they were familiar. Such addresses are, in my judgment, highly useful, setting forth the results of our own work as a society, and recalling to our minds the particular lines in which discussion would prove most fruitful. Following this course with some hesitation, I venture to offer an outline of the recent improvements and the present situation in mining and metallurgy in the Western United States. The wonderful advances in mechanics, chemistry, and electricity have all combined to aid these arts to such an extent that progress during the last decade has undeniably been more rapid than ever before in the history of the profession. In all mining countries improved transportation-facilities, in many instances called into existence by the traffic created by the mines themselves, have done much to enlarge the field of operations by the reduction of freight-, operating- and living-expenses, thereby bringing lower-grade properties into the producing class. Under normal conditions, as the age of a district increases, all these different factors should combine to off-set the augmented costs attendant on deep mining, and greatly tend to prolong the profitable life of the mines. The more recent and important improvements in our Western mining-practice which have contributed most towards the advancement of the art may be briefly summarized as follows; but, before beginning this portion of my address, I wish to thank most heartily the many engineering friends who have so

Jan 1, 1910

By Henry Howe

THE brilliant and very original matter in Professor Jeffries&apos; discussion ? should rank not only as an independent paper, but as a most important one. In particular, the explanation which it gives of the remarkable Sauveur phenomenon, over which so many of us have puzzled long and hard, is so clear, complete, and cogent as to go far toward establishing Professor Jeffries&apos; hypothesis. The very features of Professor Sauveur&apos;s photographs which fit this hypothesis so exactly are reproduced in Chappell&apos;s photographs of steel coarsened under somewhat different conditions. 1 The ideas developed by these discoveries are so novel that conven- ience of language seems to call for new conventional terms for expressing them. In, what follows here I propose certain terms for this end, for criticism and improvement, and I attempt to generalize from Professor Jeffries&apos; hypotheses. Generally speaking, a given set of grains which undergo no growth in the cold will, when the temperature is raised progressively, start to grow on reaching a certain temperature, and will continue growing at all higher temperatures. The "germinative" temperature is that at which growth begins, quite as the conditions which cause a seed to grow are "germinative." We have then. an inert temperature range below the germinative temperature, and a growth range above it, the germinative temperature being the limit between these two ranges. So, too, a germinant grain is one which is at its germinative temperature, and hence beginning to grow, while inert grains are those below their own germinative temperature, and the term "growing grains" includes those which are germinant and those which are above their germinative temperature. These last could be called "supergerminant" if the distinction should be needed.

Jan 12, 1916

By James E. York

At a meeting of the American Society for Testing Materials at Atlantic City, June, 1908, Dr. C. B. Dudley, in his presiden-tial address,&apos; showed the vital necessity of not only making a steel rail as good as in the past, but of making it considerably better in order to meet the present and prospective requiremeuts of railroads. Doctor Dudley requested the co-operation of all who from personal experience could give information that would result in bringing about the production of a steel rail that could be relied upon to meet the present requirements. I have had considerable experience in the practical manufacture of steel of almost every grade, during the past 40 years, and I shall suggest changes that will bring about the results desired. Doctor Dudley has had a long experience as chemical and metallurgical expert for the Pennsylvania railroad, but he frankly admits that up to the present time both he and other metallurgical authorities lack the practical knowledge of steel-making that is necessary to state correctly the reasons for the unreliability of the steel rails now produced. The necessity is self-evident for more positive practical knowledge on the part of these experts of what is possible and what is impossible regarding the practical manufacturing of steel rails from the ingot to the finished product. Chemical knowledge in steel-making is far ill advance of what it was years ago, and might be said to cover every requirement (in that department) for producing reliable steel. The study of the metallography of steel has been of great value, also the physical testing of steel, but this knowledge will only de-

Jan 1, 1910