Search Documents

By James F. Lewis

THE hematite iron ore mines east of the Hudson River are confined to a strip of country ten to fifteen miles wide, commencing on the south, near Fishkill, running northeast through Dutchess County, and striking the southeast corner of Columbia County, extending into Litchfield County, Conn., known there as the Salisbury mines, cropping out again at and near West Stockbridge, Lanesboro, and Cheshire, Mass., also in Bennington County, Vermont. The ores are found in beds or deposits and in veins, with a limestone ledge on one side and slate on the other, from six to thirty feet from the surface. Portions of it are quite solid, called rock ore, but

Jan 1, 1877

By Carel Robinson

THE little coal mine at Otsego, in the Winding Gulf field of southern West Virginia was dying. In the history of coal mining thousands of mines have been successful at first, but usually a change occurred and profits ceased. Often be change was so gradual and extended over such a length of time that the fundamental causes did not stand out in sharp relief and their significance was not realized. Studies often reveal that the cause for failure was in the arteries that connect the producing places with the mine entrance. Profits continued so long as the working places were close to the tipple and while the thrill of newness aid ease of access resulted in effective supervision from day to day. The air- way and haulageway, the wire line and manway, may have been sufficient when the distance from the entrance was a few hundred feet, but were inadequate when this was extended for thousands of feet.

Jan 1, 1937

By David W. Pasho

The success of a collector vehicle, designed to recover manganese nodules under the conditions which exist in deep ocean mine sites will in part be determined by the effectiveness of pick-up and running gear mechanisms. For the purpose of qualitative comparison, some specific aspects of seafloor interactions with various concepts are reviewed utilizing existing data on seafloor characteristics and running gear/tool interaction with soils.

Jan 1, 1976

By Arthur A. Brant

Let us start back as far as possible, to the beginnings of this universe, some 5 billion or more years ago. This is a time interval that can be crudely underestimated by the moon-earth tidal friction effects that have increased the length of the day by about 1/1000 second per century-from a 5 to 7 hour day to its present 24-and have moved the moon away at 5 inches per year to its present 240,000 miles. The oldest stony meteorites from interplanetary space give an age dating of some 4.6 billion years, approximating the time of formation of our earth. Further, certain stars pulsate, the period of pulsation being related to their absolute brightness. Measuring apparent brightness and comparing, gives the distance away. Thus Hubble and Shapley of Harvard, from 1925 on, were able to show that the universe reached as far as our telescopes could scan. The Doppler shift of the hydrogen red lines could only mean that the nebulae, or galaxies, were moving away at velocities increasing with their distances, by 180 km/ sec velocity increase for every million light year's distance. In short, the universe is expanding like an exploded bomb.

Jan 4, 1964

By J. J. Mike

During the past few years the combination of continuous billet casting with in-line reduction has been studied and several machines have been built with this capability included in the design parameters. (1,2,3,4,5) In-line reduction and continuous casting in combination are obvious and attractive. As pinch rolls are already in place for the continuous casting operation, it can be readily seen that a redesign of the mechanical and electrical equipment of the pinch rolls is all that is necessary to have in-line rolling. There have been numerous in-line reduction experiments conducted by simply increasing the pinch roll pressure on existing machines. (6,7,8,9) These generally failed to produce quality billets and often resulted in internal metallurgical defects (Figure 1).

Jan 1, 1972

By J. C. Swartz

New measurements of graphite and cementite solubilities in ferrite have been obtained to resolve disagreements among previous data. To measure graphite solubility, specimens of iron were equilibrated with rarious carburizing atmospheres at temperatures be-twee~z 480" and 1435°C. The carbon activity of each atmosphere relative to graphite was taken from published data. After quenching from each equilibration treatment the concentration of carbon (typically 10 pprn by wt) was determined from the height of the Snoek peak in the internal friction spectrum. A few inclividual analyses by combustion support the reszdts of Smith on the solubility of graphite near the eutectoid temperature. Combination of these combustion and internal friction analyses determines In a, (at 0.01 wt pct) = 24,000/RT - 12.72, where a, is the activtity relative to graphite in ferrite at fixed cornposition. The same specimens were used to determine the solubility of self-stressed cementite precipitates. The results indicate solubilities of 6.3, 23.2, and 68 pprn carbon by wt at respectively 400°, 500". and 600°C. The once large discrepancy between the cementite solubility determined by internal frictiori and that calculated from flee energy data has been almost completely resolved. A recent study1 (hereafter designated I) on the solubility of cementite in a iron did not fully resolve the disagreement among previous data. The remaining disagreement is illustrated by the phase diagram in Fig. L The data of I are represented by the line labeled "stress-free" cementite. They determine a heat of solution of cementite of (14.8 * 0.2) kcal per mole which contrasts with the (20 * 1) kcal per mole derived from Smith's graphite solubility2 and the formation energy of cementite.3 Toward resolving this disagreement we have obtained new data on the solubilities of graphite and cementite. METHODS As in I the Snoek peak in the internal friction spectrum was used to measure the concentration of carbon dissolved in ferrite. This method relies on the relation C=kQ-1 [1] in which C is the concentration of dissolved carbon, Q-I is the Snoek peak height, and k is a proportionality factor which is a function of the peak temperature, polycrystalline texture, and other parameters characteristic of the ferrite lattice. To determine true heats of solution via Eq. [1], it is necessary to establish that k is independent of the temperature from which the specimen is quenched. Some evidence on this point is contained in a separate report.* Additional evidence is shown by the data points in Fig. 1. These represent the Snoek peaks of two specimens carburized to about 10 ppm C, copper plated, and quenched first from 888º then from 588°C. The copper plate was removed before each Snoek peak measurement. These data show that there is no detectable dependence of k on quenching temperature. The solubility of graphite was determined by repeatedly carburizing various specimens of iron wire with gas mixtures of known carbon activity relative to graphite. To cover a wide temperature range within the a phase boundaries it is desirable to use as low a carbon concentration as is compatible with reasonable precision. With the present internal friction apparatus the best compromise of these desires is a concentration near 10 wt ppm. The dashed line in Fig. 1 was used to approximate the activity of carbon* for

Jan 1, 1970

By E. C. Lee

THE safety of mine workers has received more attention from both State and Federal law-making bodies than any other industry, a fact that shows clearly the hazardous nature of the industry. The last, but by no means the least, of the measures adopted for the protection of mine workers, is workmen's compensation legislation. This is proving to be a powerful instrument for greater safety in the industries, from the fact that special stress is laid not on how the accident happened or who may have been responsible for it, but on how badly the employee is hurt by it. The injured person does not have to employ lawyers to prove his case, because the mere fact of his employment is proof of his right to compensation. The immediate effect of such legislation is the certainty confronting the mine operator that he must pay out large sums for every accident, regardless of its cause, thus adding materially to the cost of the production of his coal. This fact furnished to the operator the strongest incentive to reduce the causes of accidents; not that the operator has ever lacked reasonable consideration for the welfare of his employees and a proper humane interest in their safety, but his engrossment in earning his daily livelihood has been so great that he has not felt that he had the time to devote to the safety of the operation. This time he must now find because of the actual-cash value of the prevention of accidents in his mines. This agency alone proved inadequate to bring about a material improvement because operators have always been willing enough to improve safety conditions when possible to do so within reasonable limits of their financial ability. The requirement in the Workmen's Compensation Laws of several of the States, that the mine operator shall insure as a guarantee of his ability to meet his compensation obligations, has furnished the needed incentive, moral and financial, necessary to the prompt and effective dissemination of a more general knowledge of the causes and

Jan 10, 1917

By Elmer W., Pehrson

NOT much serious consideration was liven to the military aspects of raw materials before World War 1. Following the outbreak of war in Europe in 1914, however. this situation was promptly changed. Disruption of allied shipping and German submarine warfare soon cut off a substantial part of the material the United Staten was accustomed to receiving from overseas. At the same time, raw material requirements rose rapidly as the tempo of industrial preparedness was stepped up in anticipation of war. By April 1917, when we entered the war, serious shortages threatened and consideralde attention was being given to our "deficcient" raw materials. The term "war mineral," began to appear after we became active combatants. But there is no evidence that "strategics" and "critical." as now used, had entered the lexicon of our raw materials experts during the last war nor were there apparently any officially recog¬nized list or definitions of what con¬stituted war materials. According to G. A. Roush in his book, `'Strategic Mineral Supplies," C. K. Leith, while serving as mineral advisor to the War Industries Board. compiled the first unofficial list of deficient minerals in 1917.

Jan 1, 1944

By H. M. Wilten

THIS article presets a view of a problem encountered in petroleum refining in the deterioration of equipment used in condensation of vapors and cooling of liquids. Discussion is limited to the problems of shell- and tube-type exchangers and condensers. In this service shell- and .tube-type equipment is gradually displacing other types and, for this reason, its economic importance ill oil-refining practice is also increasing. Considering oil - refinery practice during the last two decades one can readily see many important improvements in the apparatus used. Briefly, the present equipment is safer, more efficient, and Ignore economical. Improvement in apparatus used for the condensation of distillates has, in my opinion, been less than that in other essential distilling apparatus. So it is hoped that this discussion will stimulate research among the producers as well as among the consumers of this equipment with a view to ameliorating this condition.

Jan 1, 1937

By JOHN D. SUMMER

THE Premium Price Plan for copper, lead, and represent, the approach of the Office of Price Administration to the urgent of wartime problem of securing increased output of nonferrous metals. Some of the problems encountered in too operation of the Plan and the considerations which led to it?s adopt it will here he reviewed. The Plan provides for extra payment by the Metals Reserve Co., to mine operators who exceed established quotas of production. Producers are thus directly, compensated for the higher costs of working ores that are not commercial at the ceiling price, although the metal obtained from these ores is directed into regular channels of distribution at the established prices for copper, lead, and zinc. Higher-cost metal is thus available to fabricators and to the government agencies at the regular ceiling price and the dual objective of increased production and table pries is achieved.

Jan 1, 1943

By Norman D. Fitz, Gerald

BOTH physical and economic factors are concerned in determining the optimum rate of depletion of a mineral deposit. The physical limitations are, in a large measure fixed by nature. Economic influences on the other hand, are man-made and subject to wide changes. Analyses of the interrelations of these two groups of factors are of major importance in selecting the optimum rate of production of petroleum and mining properties and in their valuation. Physical Influences PRIMARY limitations on the rate of mining are the rate of shaft sinking and underground development, the rate of hoisting, and the rate of sloping. These rates are largely determined by the physical features of a property. Technical methods which may be employed, and consequently the length of time required, are governed by the dimensions of the deposit, its attitude, depth, regularity, the unit value and character of the ore, the nature of the wall rocks, and similar factors.

Jan 1, 1938

By H. F. Haller

COLUMBIA-SOUTHERN'S Barberton limestone mine, 8 miles southwest of Akron, Ohio, is a million-ton-per-year producer from a depth of over 2200 ft in a district where other underground mining at this depth is unknown. Mining extracts 46 of the top 51 ft from a formation of Devonian limestone discovered by drilling in the 1890's. The same drilling revealed extensive salt deposits below the lime- stone, which led to the location of the chemical plant at Barberton as a division of the Pittsburgh Plate Glass Co. in 1899. Soda ash was the principal product of the plant, and as production increased the demand for limestone increased. Columbia's first attempt to secure a reliable all-weather source of stone was the development of a quarry at Zanesville, Ohio, in 1919. Zanesville production eliminated some of the stock- piling required by the use of Michigan stone, avail- able only during the lake shipping season. Stone from some Zanesville horizons, however, was found to be more suitable for cement production than for soda ash, and rail transportation remained an important factor. As demand continued to increase, plans were made to develop the Barberton deposit.

Jan 12, 1954

By A. Heim, M. Gondouin

Invasion experiments were run on Berea sandstone cores to get laboratory measurements of resistivity and saturation profiles characteristic of water and oil sands invaded by mud filtrate. Injection rates were as low as 1.13 cm/D, and the cores were 30 to 36 in. long, cut parallel to the bedding planes. In the water-sand case, the resistivity profiles revealed the existence of an extensive transition zone between flushed and uncontaminated zones. In the linear geometry of the experiment, the width of the transition zone increased as the square root of the injected fluid volume. For the oil-sand case the core was prepared by displacing the formation water with kerosene to minimum water saturation. During the subsequent invasion experiment. oil saturation was measured directly by means of an oil-soluble radioactive tracer, and resistivity profiles along the core were taken at the same time. These data were interpreted in terms of an oil-water front, followed by a formation water bank, a zone of mixed waters, and finally, invaded mud filtrate near the borehole. Micro-fingering and capillarity seemed to affect considerably the resistivity profiles observed in the invaded oil-sand experiment. Beyond the regular conductive annulus or "low zone", it was found that a resistive "anti-annulus" could also be formed. As a result of these experiments, some simplified invasion profiles have been accepted and are being used in Grand Slam* interpretations. INTRODUCTION The importance of the mud filtrate-invaded zone in interpreting electrical logs has long been recognized.',* In trying to account for its effect, only very simple models of the resistivity profiles in the radial direction from the borehole have been used. In fact, most log interpretation charts have been based on resistivity models consisiting of two media of uniform resistivity (R, and R,) abruptly separated at the diameter of invasion. Such a clean separation of the media of different resistivities seems unrealistic, since flushing may not be perfect and may vary with radial distance into the formation.3** The nature of the transition zone, when it is within the radius of investigation of the surveying devices, may affect the log readings. Campbell and Martin' verified that a conductive annulus containing a high percentage of formation water may be formed when mud filtrate invades an oil-bearing sand. Interpretations which are to include the effect of such an annulus require the addition to the model of a conductive zone located at the outer rim of the invaded zone.' Using the Buckley-Leverett relations,6 aturation profiles may be derived, from which resistivity profiles can be calculated. Results of such computations by K. S. Kunz and J. H. Moran were given in a paper by Dumanoir. Tixier and Martin,7 and led to the construction of log interpretation charts which were based on a representation with three media of resistivities R, R0 and R1. Fig. 1 shows a schematic representation of a resistivity profile which includes an annulus. Campbell and Martin realized that, during the invasion of an oil sand, both capillarity and mixing would contribute to rounding of the profile shown in Fig. 1. Capillarity tends to draw some of the formation water from the annulus into the uncontaminated (Rt) zone, whereas mixing of the mud filtrate with formation water of the

Jan 1, 1965

By N. F. Fiore, M. C. Mangalick

DISLOCATION damping in single crystals is orientation dependent.&apos; If dislocations are distributed uniformly over all the slip systems in a crystal, and if each dislocation contributes identically to the damping process, then a damping loss or decrement 6 arises. In fact, however, for a crystal of axial direction (hkl), dislocations on certain slip systems are oriented to make a larger contribution to the damping loss than are dislocations on other slip systems. Thus the measuring damping, 6 (hkl) is proportional to an orientation factor (hkl), which weights the ability of each slip system in the crystal to contribute to the total damping. If it is assumed that dislocations are distributed uniformly on all slip systems, then for a given orientation of an fcc crystal this factor is determined2,3 by the three nonzero elastic constants Cll, C12, and C44 and the density p. In this communication measured values of elastic constants for two Fe-18Cr-Ni alloys are reported, and the dislocation damping results on two different orientations of each alloy are analyzed for orientation dependence. Elastic constants were determined by measuring the ultrasonic velocities of one longitudinal and two shear waves in (110) direction of the fcc crystals.4 Variation of velocities with the change in orientation is very small for (110) orientation,3 and so this direction is ideal for orientation factor and comparative damping measurements. Experimental Procedures. The nominal compositions of the alloys studied are given in Table I. These alloys were vacuum-melted and vacuum-cast from high-purity materials at U.S. Steel Applied Research Laboratories. The single crystals were grown by the modified Bridgeman technique. The specimens were homogenized at 1350°C for 20 hr, cut to shape and size with a spark cutter, and then annealed at 1100°C for 20 hr prior to use. In the KHz frequency range, the Marx composite piezoelectric oscillator was used to obtain the damping. The ultrasonic pulse technique was used to measure the ultrasonic velocities and the attenuation in the MHz frequency range. M.c.mANGALICK,-- StudentMemberAIME,formerly Research Assistant, University of Notre Dame, is now with Casting Laboratory, Chase Brass and Copper Co., Cleveland, Ohio. N. F. FIORE, Associate Member AIME, is Assistant Professor, Department of Metallurgical Engineering and Materials Science. University of Notre Dame, Notre Dame, Ind. This communication is part of a Ph.D. thesis presented by M. C. MANGALICK to the Graduate School of the University of Notre Dame. Manuscript submitted May 20. 1968. IMD Elastic Constants. Table I gives the values of the ultrasonic velocities. Values of C11, C12, and C44 calculated from these velocities are also given in Table I, and it is evident that there is very little variation in C11, C12, and C44 with nickel content. This slight variation may be attributed to inaccuracies in velocity measurements and practical differences in the orientations of the specimens. For example, in B the time interval for vl was 2.4 ± 0.05 sec giving an error in v1 of 0.235 x or 0.005 in. per sec. The elastic constants obtained by pulse technique were tested by calculating E<110>, Young&apos;s modulus for the (110) direction, from the equation: This value was compared with the value computed from the resonance bar measurements in which where fr is the resonance frequency and I, is the length of the specimen. In all cases, the values calculated from the ultrasonic velocity measurements

Jan 1, 1969

By William P. Lohden

INTRODUCTION It is recognized that, for a variety of reasons, some companies in the mineral industry today are by no means cash-rich and, in fact, are reporting a growing proportion of long-term debt in their capital structures. A review of recent balance sheets of small, medium-size, and some larger companies, indicates that a fair number still have substantial positions in cash equivalents such as U.S. government issues and other short-term money market instruments. In part, this paper concerns itself with companies which have sufficient cash and equivalents and/or cash generation to internally finance mining projects or expansions but which, for some reason, choose to borrow funds. Misconceptions which appear to frequently underlie so-called "leveraging" decisions are explored in this paper. Also considered arc&apos; those circumstances under which any company, including one that is cash rich, should consider borrowing for a project in an amount beyond what would otherwise be necessary based upon its internal financing ability. I do not attempt to cover the raising of equity capital in public markets in this paper. OVERALL RETURN ON INVESTABLE CASH If you approach an individual with an investment which can be financed from savings, or by borrowing at a rate higher than one is earning on savings, that individual will quickly tell you that to pay interest at a rate higher than is being earned on savings would reduce overall income. Assuming that additional investment opportunities are not currently being considered, the individual concludes that a draw-down on savings, leaving a cushion for contingencies suited to individual circumstances, is the correct financial decision. For reasons discussed later, the simple mathematical logic leading to this conclusion tends to become obscured at the corporate level. When Leveraged Studies Are Inappropriate or Premature Surprisingly, I have heard of a number of companies that could afford to finance an investment solely with internal funds, which have made DCFROR (i.e. discounted-cash-flow rate-of-return) studies not only on a 100% equity basis but also on a leveraged basis. Certainly, a leveraged study would be appropriate if additional projects were competing for more capital than was available internally. Often, however, other projects are not far enough along to warrant a leveraged study and there is some danger that a project may be undertaken because it has an estimated acceptable rate of return, on a leveraged basis, that is not ultimately earned because some of the other projects are postponed or abandoned and borrowing is less than expected. For the above reasons, until it has been determined that (1) borrowing is a reasonable certainty for a particular project and (2) the timing and amount to be borrowed has been determined within a reasonable range of accuracy, I believe it is inappropriate and misleading to calculate DCFROR for a project other than on a 100% equity basis. Even when there are several projects currently competing for funds and borrowing will be required to finance one or more of them, using the common yardstick of calculating DCFROR on a 100% equity basis is a safer method to initially evaluate and compare the attractiveness of the projects. Many companies, whether they would have to borrow or not, will reject projects that on a 100% equity basis do not meet their minimum rate of return standards. Some companies which have to borrow will undertake a project provided the project&apos;s DCFROR on a leveraged basis meets its minimum return standards. The danger of this approach is that even moderate shrinkages of estimated cash flows could plunge return below

Jan 1, 1985

By William B. Plank

ENROLMENT data given in this report of the seventh study of the schools by the Mineral Industry Education Division reveals the critical situation in the mineral engineering schools of the United States. Complete figures for the year 1942-43 show that at that time, about one year after Pearl Harbor, the enrollment of mineral engineers was 6385 or 30 per cent less than in 199441. By October 1943, however, enrollment had dropped to 2050, as reported in the Journal of Engineering Education of January 1944. This was a further reduction of 68 per cent in one year, or 77 per cent in three years. With accelerated programs in effect during the current year, with many graduations since last October, and with the military forces taking practically all the high school graduates, the present enrollment is, of course, much lower than the 2050 above given. There are no late data on the exact situation. In Canada, the same situation exists in the mineral engineering schools, only

Jan 1, 1944

By C. E. Lawall

ONE of the most important developments in the coal industry during 1940 was the continued uptrend in the production of bituminous coal. Estimated production for the year is 450,000,000 tons, with an additional production of anthracite of 50,000,000 tons making a total of approximately 500,000,000 tons. This is an increase of 12.5 per cent over 1939. Despite an estimated decrease of about 3.5 per cent in anthracite production, all of the major coal-producing states had increases in production for 9140. The national defense program, with the consequent increase in industrial activity, undoubtedly had an important effect on the increased demand for coal.

Jan 1, 1941

By C. B. Murray

Our experience from time immemorial has been that the furnace sampler and analyst usually find one or two, and sometimes more, points less iron than the Lake Superior shippers, but, fortunately, their contracts are iron bound…

Jan 1, 1915

By D. J. Blickwede

WHEN iron is dipped in molten zinc at temperatures in the range 840" to 930°F, the two metals react to form layers of Fe-Zn compounds which adhere to the iron. At the galvanizing tem- perature, the successive layers are:&apos; y (Fe5Zn21), 61 (FeZn;), and 5 (FeZn13), in conformity with the Fe-Zn constitution diagram. There is no quantitative information in the literature on the rates of growth of the individual alloy layers over the temperature range 840° to 930°F. Rather all the past experiments have studied the loss in weight of iron as a function of galvanizing

Jan 1, 1954

By J. Leja, N. Sheikh

The stability of lead ethyl xanthate precipitate in aqueous environment of different pH (4.5 to 10.5) and at temperatures 25°C-60°C was investigated. Dissolution leads to a wide variation of pH, xanthate, and lead ions concentration in solution and to a deposition of solid products of reactions. X-ray diffraction patterns of these solids enabled identification of Pb(OH)3, PbCO3, and PbS as constituents of the remaining undecomposed Pb(EtX)1, together with some unidentified compounds (which give rise to intensive peaks with d values of 2.82A and 1.71A, and numerous peaks of lesser intensity).

Jan 1, 1974