Search Documents

By J. Gurland

THE microstructure of sintered carbides consists of particles of metal carbides, such as WC and TiC, embedded in a metallic binder which is usually a cobalt—or nickel-rich solid solution. One of the important factors influencing the strength of the alloys is the degree of dispersion of the carbide particles in the binder matrix. While it is generally accepted

Jan 1, 1960

By N. H. Murlenberg, T. M. Drown

It is often a tedious matter to get a solution of pig iron or steel, for the determination of phosphorus, which is absolutely free from silica. Where pig iron rich in silicon is dissolved in hydrochloric or nitric acid in the usual procedure, it is necessary, not only to evaporate the solution to complete dry ness, but to heat the dry residue for some beam in an air-bath to a temperature of about 120° C. The oxide of iron is thus rendered insoluble in nitric acid, and is only slowly dissolved by hydrochloric acid. In the method of determining silicon by nitric and sulphuric acid, described in the Transactions of the Institute, Vol. VII, page 346, arid Vol. VIII, page 508, we obtain in one or two hours a solution of the iron in the form of ferric sulphate entirely free from silica, and containing free sulphuric acid. It occurred to Us that this solution might be made available for the determination of the phosphorus by the molybdate method. The following experiments mere tried with unsatisfactory results. 1st. The iron was precipitated by ammonia, the precipitate filtered, washed, and dissolved in nitric acid. 2d. The iron was precipitated as basic acetate and dissolved in nitric acid. 3d. The solution was neutralized by ammonia, and nitric acid added in small excess. In all these cases the phosphorus obtained by precipitating by ammonium molybdate and magnesia-mixture was too low. The following method was then tried with success. The filtrate from the silica and graphite was evaporated to small bulk and heated in a porcelain dish on a sand-bath. until fumes of sulphuric acid ceased to escape. The dry residue was taken up with dilute nitric acid and the solution precipitated by ammonium molyldate. The phosphorus was weighed as magnesium pyrophosphate. The results were satisfactory. To save time, the original solution of the iron in nitric and sulphuric acids was evaporated to dryness and heated as before until

Jan 1, 1882

By N. H. Muhlenberg

IT is often a tedious matter to get a solution of pig iron or steel, for the determination of phosphorus, which is absolutely free from silica. Where pig iron rich in silicon is dissolved in hydrochloric or nitric acid in the usual procedure, it is necessary, not only to evaporate the solution to complete dryness, but to heat the dry residue for some hours in an air-bath to a temperature of about 120° C. The oxide of iron is thus rendered insoluble in nitric acid, and is only slowly dissolved by hydrochloric acid. In the method of determining silicon by nitric and sulphuric acid, described in the Transactions of the Institute, Vol. VII, page 346, and Vol. VIII, page 508, we obtain in one or two hours a solution of the iron in the form of ferric sulphate entirely free from silica, and containing free sulphuric acid. It occurred to us that this solution might be made available for the determination of the phosphorus by the molybdate method. The following experiments were tried with unsatisfactory results. 1st. The iron was precipitated by ammonia, the precipitate filtered, washed, and dissolved in nitric acid. 2d. The iron was precipitated as basic acetate and dissolved in nitric acid. 3d. The solution was neutralized by ammonia, and nitric acid added in small excess. In all these cases the phosphorus obtained by precipitating by ammonium molybdate and magnesia-mixture was too low. The following method was then tried with success. The filtrate from the silica and graphite was evaporated to small bulk and heated in a porcelain dish on a sand-bath, until fumes of sulphuric acid ceased to escape. The dry residue was taken up with dilute nitric acid and the solution precipitated by ammonium molyhdate. The phosphorus was weighed as magnesium pyrophosphate. The results were satisfactory. To save time, the original solution of the iron in nitric and sulphuric acids was evaporated to dryness and heated as before until

Jan 1, 1882

By John Fulton

Early in the year 1875, some difficulty was experienced in the " Old blast-furnaces " of the Cambria Iron Company, at Johnstown, Pennsylvania, arising from the increased use of native coke, prepared in Belgian ovens near the furnaces, in mixture with Connellsville coke, in the production of Bessemer pig-iron. This was the more surprising at that time, because a very caulplete coal-crushing and washing apparatus, after the Bradford plan, had just been put into successful operation, affording a pure coal for coke-making. It was confidently expected that this thorough cleansing of the coal would improve the quality of the coke and fit it for the increasing manufacture of Bessemer pig-iron. But the trouble with the native coke continued. Experiments in fuel charges-increasing and reducing them—failed to correct the irregular working of these furnaces. Increasing the charge of native coke produced abnormal heat at the top of the furnace, reducing it cooled the furnace below. At this stage of affairs, the Hon. Daniel J. Morrell, general manager of the Cambria Iron Company, requested the writer to make the requisite investigation to determine the nature of this coke-difficulty, and to ascertain why the Johnstown coke could not be used in blastfurnace work as well as Connellsville. This task at first did not appear to present any special difficulties, but subsequently it expanded into proportions that caused no little anxiety. The first effort was directed to procuring average samples of Johnstown and Connellsville coke. At this period of the investigation, it was assumed that the whole matter could be intelligently solved by comparing the chemical analyses of the two cokes: Johnstown Coke. Connellsville Coke. Moisture,.......... 0.30 Volatile matter,......... 0.46 Fixed carbon,.90.48 89.57 Ash,.8.96 9.11 Sulphur,.0.56 0.82 Phosphorus,..... 0.014 100.00 100.274 Analysts, T. T. Morrell. A. S. McCreath.

Jan 1, 1884

By John Johnston

The actual amount of any metal volatilized from a mixture of metals depends on the magnitude of its partial vapor pressure under the specified conditions of temperature, and on the circumstances attending the heating—in particular, on the duration of heating, the volume of gas coming into actual contact with the surface of the metal, the extent of this surface, and the rate of diffusion of the volatile metal from the body of the melt toward the surface.' If two (or more) metals are volatilizing from the same mixture of metals, the several conditions are identical except for the difference in partial pressure and in rate of diffusion of the volatilizing metals; the second of these two factors is without doubt only of secondary importance as it is probable that the rates of diffusion of the volatilizing metals would be very similar. Hence, in order to gain an estimate of the relative amounts of two metals that may be volatilized from a given mixture, it is necessary to know the vapor pressure, or, more precisely, to ascertain for each metal its partial vapor pressure in equilibrium with the liquid (or solid) alloy under the particular circumstances. The partial pressure of each constituent depends on the effective concentration of that constituent in the alloy2 as well as on the vapor pressure of the constituent when pure, and it can be calculated when both of the above factors are known. The first step, therefore, is to ascertain the vapor pressure of the several pure metals. Vapor Pressure of Pure Metals The experimental data on the vapor pressure of the several pure metals with which we are here concerned are not so accurate as could be wished, nor have the determinations been made in general at temperatures such that the results can be used directly. In a previous

Jan 1, 1919

By Ralph A. Sherman

In these days of intense competition for the domestic fuel market much is heard of the low efficiencies with which solid fuels, and most particularly bituminous coal, are burned in domestic heating equipment. In contrast to the every-day operating efficiencies of 85 and 90 per cent in large, central, electric-generating stations, efficiencies of 50 per cent and lower are cited for the hand-fired home furnace. Just as the miles per gallon of gasoline is only one of the factors that determine the cost of operation of an automobile, so the thermal efficiency is only one factor in the cost of domestic or other heating. The purpose of this paper is to analyze the total costs of domestic heating by various fuels and types of equipment, to determine the relative importance of efficiency and other factors, and to discuss what this signifies relative to the future of the use of fuels in the home. Factors That Govern the Choice of Fuel and Burning Equipment A rational, intelligent selection of fuel and equipment for heating the home would consider two groups of factors: Cost Factors Convenience Factors 1. Cost of potential heat in fuel 1. Attention 2. Efficiency of combustion and heat transfer 2. Dirt 3. Fixed charges 3. Noise a. Interest b. Depreciation c. Repairs 4. Power costs 5. Cost of handling ash and refuse. As just stated, the purpose of this paper is to analyze the relative importance of the five cost factors and not to discuss particularly the relative total costs of different methods of heating. However, to arrive at the percentage costs and to show clearly how they were determined, a statement of the total costs is unavoidable. One example only will

Jan 1, 1934

By Janshi Sen

VERTICAL-INTENSITY magnetometers, such as the Hotchkiss Superdip and the Askania vertical field balance, are now [ ] widely used, because vertical-intensity charts give definite information for the location of upper pole, dip and strike, and approximate shape of the deposit. Again, a slow and steady increase of dip over a large area indicates a large deep-lying deposit, while a large dip limited to a small area and falling away rapidly suggests a small and shallow one. The complication comes more from the richness of the ore. A large body of lean ore near the surface might produce the same vertical-intensity chart as a rich ore at depth. This paper presents a method for calculating the maximum depth of a single-pole deposit and another for a two-pole mineral body, by utilizing data of both vertical and horizontal intensities as obtained by a Thalen-Tiberg magnetometer. As shown on the left side of Fig. 1, lean ore, rich ore and a single pole produce the same magnetic field. The depth of the pole, [ ] h, can be calculated from the following relation: [h=a=tan¢=G-F h=aXFy] where G is the vertical intensity at point A due to the pole; F, the horizontal intensity of the same; and a, the distance from the point of maximum vertical intensity or the vertical projection of the pole on the surface to the point of observation A. If an entirely covered deposit is indicated by magnetic measurements and boring cost estimated from the calculated depth is so reasonable as to encourage drilling, the ore should be struck somewhere within the limit of the calculated depth by the borehole. A number of such points as A should be taken for calculation, erratic results should be rejected and the average figure used for cost estimation.

Jan 1, 1944

By David, Cole

THE years 1914-15-16 were a pioneering period in mining, milling, and copper metallurgy generally. It was uncertain just what path the crushing, grinding, and concentrating processes would take. This situation was quite embarrassing to the directors of some of our large porphyry properties, then being equipped for production. Inspiration had already made several designs for its proposed 15,000-ton concentrator, incorporating in them the latest devices developed in the art of gravity concentration, only to have the work vitiated by the rapid march of events. In a little improvised plant, built on ground that is now in the crater of subsidence over the Inspiration- Miami orebodies, flotation was being experimentally ' applied to Inspiration ore by Minerals Separation engineers in 1914, with results indicating that this process would be of major importance in the concentration of the sulfides. How best to apply it, and especially how to crush and grind the ore to the very much finer sizes required for the new process, was a serious question, properly to be answered only by doing it, in full- sized machines, under regular 'operating conditions.

Jan 1, 1931

The early history of a country is linked with its topographic features. Mountains are barriers, rivers are avenues, the sea is a highway. The first Europeans to reach the northwestern corner of the American continent, now known as Alaska, came from Asia, for the Pacific Ocean provided an approach by means of the islands that like stepping-stones stretch far westward from the inhospitable shore of the mainland. The Russians crossed Siberia and explored the Arctic coast of Asia. In 1728 a band of Cossacks was driven by a storm eastward from Kamchatka, and landed in Norton Sound.* Others followed them, and settled on the islands and peninsulas of southeastern Alaska. The mountains guarding the coast discouraged any advance into the interior. Another range, the northern extension of the Rocky Mountains, barred the westward progress of the French voyageurs and the English fur-traders of the Hudson's Bay Company. After the Russians had obtained a foothold among the Indians, the viceroys of Mexico sent successive expeditions up the coast, such as that of Pérez in 1774 and of Heceta in 1775. If the English fur-traders had not interfered, the Spanish and Russian spheres of influence would have conflicted, and the contest for control might have ended in establishing a line of demarkation somewhere near the mouth of the Columbia river. The British navigator Captain James Cook landed near Sitka in 1778 while seeking a way by water to Hudson Bay. Fifteen years later his midshipman, George Vancouver, in command of another British expedition, surveyed the coast

Jan 1, 1932

By C Gunther

Ore deposits are commonly divided into two classes, syngenetic and epigenetic, according to whether the ore was deposited together with the enclosing rock or was introduced after its deposition or solidification. Epigenetic deposits, which are by far the more important class, owe their formation to the channels that permitted the ingress of their metals, and both classes are subject to great modification by post-mineral changes in the containing rocks. A discussion of the structural features of rocks, therefore, necessarily precedes any consideration of ore deposits or processes of ore deposition. The arrangement of sediments in parallel and approximately horizontal layers is called stratification, and is an original prop¬erty of sedimentary rocks. Successive strata of the same sedimentary bed commonly differ from each other in some minor characteristic, such as texture or color, which results in a bedded or stratified appearance. The subjection of a rock to pressure develops within it parallel planes of weakness, called cleavage planes, along which the rock breaks into relatively regular slabs or blocks; the direc¬tion of these cleavage planes, which bear no relation to stratifica¬tion, is determined by the direction of the pressure that produced them. Where there are more than one set of cleavage planes, one of them is likely to be more prominent than the others. In sedimentary rocks, the cleavage may coincide with the stratifica¬tion but more commonly cuts across it. Van Hise has defined cleavage as the "capacity present in some rocks to break in some directions more easily than in others." Cleavage, therefore, does not imply the existence of subdivisions, but rather the tendency to subdivide along certain planes.

Jan 1, 1932

By W. A. Barrows, Carl Zapffe

Jan 1, 1913

By James K. Greenlee, David W. Wisecarver

It is estimated conservatively that some 14 billion tonnes of coal reserves in the United States exist in beds considered steeply dipping, i.e. at pitches or slopes in excess of 15O - a slope too steep for practical use of mobile wheel or crawler drive mining equipment. Past attempts to mine these steep reserves are limited owing to production difficulties and high costs, an expected result when mining of slopes must be done conventionally and mining on strike with mobile mining equipment is restricted because of limited cross sectional opening and operating room. In Europe, these adverse conditions are countered through the use of the longwall mining method. In fact, longwall mining is employed along pitches up to 55°. However, both operating and administrative - conditions in foreign steep seam coal mines differ from ours in that (1) the mine does not necessarily have to make a profit and (2) single entry development of retreat mining panels is acceptable practice. In the United States development can be done with a minimum of two entries only, provided belt haulage is not used during development.

Jan 1, 1981

By Carl Scholz

DURING November And December, 1907, Four Serious Mine-explosions Occurred In The Appalachian Coal-Field, Which Resulted In The Loss Of Nearly A Thousand Lives And Caused An Enormous . Damage To Property. These Accidents Attracted More Than The Usual Attention; Coal-Trade And Engineering Papers Contained Many Comments And Suggestions On The Cause And Prevention Of Accidents; The Daily Press In Many Instances Condemned The Coal-Operators And Charged These Accidents To Their Negligence, Or Their Anxiety To Make Money Without Adopting Precautionary Measures. Immediately After Each Accident The Respective State ..Authorities Ordered Close Investigations To Be Made, With The View Of Establishing The Cause And Suggesting Remedies To Prevent Recurrence. Representatives Of The Technologic Branch Of The U. S. Geological Survey, To Whom The Investigation Of Mine-Accidents Had Recently Been Delegated By The Secretary Of The Interior,. Visited The Mines And Co-Operated With The Local Authorities In Their Determinations. It May Be Safe To Say Here That An Investigation Of A Mine After An Explosion Has Occurred Discloses But Little, Because. The Causes Have Been Removed And Conditions Have Been Entirely Changed. On Jan. 8, 1905, The Coal-Operators Of West Virginia Organized An Association At Washington For The Purpose Of Making Extensive Investigations, And Sufficient Funds Were Pledged To Carry Out This Work. At This Organization Meeting, The Representatives Of The Geological Survey Present Had No Suggestions To Offer As To The Cause Of These Accidents. An Examination Of The Various Reports Concerning These Accidents Indicates That The Explosions Were Caused By The Ignition Of Gas Or Dust; They Show The Point Of Origin And The Direction In Which The Force Was Expended, And Give A Detailed Description Of The Damage Done. Very Little Has Been Said As To What

Jan 7, 1908

The Library of the above-named Societies is open from 9 A.M. to 9 P.M. on all week-days, except holidays, from September 1 to June 30, and from 9 A.M. to 6 P.M. during July and August. The Library contains about 55,000 volumes, including sets of technical periodicals and the publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library can render valuable service through correspondence; letters requesting information will receive special attention. The Library is prepared to furnish references and copies of articles on mining and metallurgical subjects; to determine the existence of mining-maps, and to furnish general information as to the geology and mineral resources of all countries. All communications should be made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable-shape. The members of the Institute can be of service to the Library by forwarding copies of mining-reports, maps privately issued, and similar material, which will be classified, indexed, and made available to other members. Suggestions for additions to the Library, either by purchase or personal solicitation as gifts, will be welcomed. It is hoped that members while in the city will use the Library freely, and assurance is given that most careful service will be rendered to them.

Jan 2, 1914

By L. D. Anderson

WHEN, after years of troublous experiences in roasting sulfide ores with heavy dust and fume losses resulting from the equipment and methods first available, there appeared on the, scene of metallurgy that revolutionary process known as sintering, it was felt that at last there had been found the ideal method for preparing sulfide ores for blast-furnace reduction. Not only were the sulfides roasted but also the fine oxidized ores were bound together with them in strong porous cellular masses which were in the best possible condition for reduction. With the experiences gained in the manipulation of the Huntington-Heberlein, Carmichael-Bradford, and Dwight & Lloyd processes there developed a refinement of detail which brought the whole plan of roasting by sintering to a high plane of perfection. But that metallurgy is never stationary is revealed by the fact that changes in milling practice, particularly the development of flotation, have introduced a new set of problems in sintering itself. Inasmuch as it is felt that these problems have not yet been solved in an entirely satisfactory manner this paper is written to record the present practice of the Salt Lake Valley smelters with the hope that there will be brought forth such discussion as may perhaps lead to still better practice. By far the greater proportion of the sulfides smelted today are flotation concentrates. Usually they are high grade, sometimes as high as 70 per cent. and more in lead. They are extremely fine, many mills grinding the ore so that from 60 to 80 per cent. will pass through screens of 200 mesh. The physical condition in which many of these concentrates reach the smelters is disconcerting to the metallurgists. Some are of about the consistency of putty. Others are of a sticky, slimy nature. Others again, dried to the limit, are veritable powders. Remembering that the down-draft sintering charge for the best results must be porous enough to let air be drawn through it reasonably well, must be thoroughly mixed, and must have some coarse material in it to segregate out and form a layer on the grates, it will be understood that the advent of this extremely fine material has made necessary still further elaboration in the equipment and processes of preparing sulfides for the blast furnaces, all of which is expensive. The high metal contents of the concentrates

Jan 1, 1929

By Don B. Carson, Donald L. Katz

NATURAL gases under pressure form crystal-line hydrates with water. Experimental data are reported on four-phase equilibrium for the methane-propane-water, methane-pentane-water, and methane-hexane-water systems. Temperatures and pressures for equilibrium between gas, water-rich liquid, hydrocarbonrich liquid, and hydrate were measured, as well as the percentages of methane and propane in the hydrate. The data indicate that natural gas hydrate behaves as a solid solution and that pentanes and heavier hydrocarbons do not enter into the solid phase. Vapor-solid equilibrium constants are presented that permit the approximation of the conditions for hydrate formation, from the composition of a gas. INTRODUCTION Natural gas hydrates have been the object of considerable research in recent years, because of the trouble they have caused in the natural-gas and natural gasoline industries. Natural gas hydrates are white crystalline compounds of water and gas, which, under pressure, exist at temperatures considerably above the freezing point of water. Because of the relatively high temperatures at which the hydrates exist, they become a nuisance in high-pressure gas operations where water is present, since their formation causes partial or complete plugging of valves and pipes. From a practical standpoint, the trouble incident to hydrate formation has been solved by dehydration of the gas before it enters the plant or pipe line, or by other remedial measures. Extensive work on gas hydrates in the latter part of the nineteenth century, by Villard1 and others, gave data on methane hydrate and on ethane hydrate. Schroeder summarized these theoretical studies.2 Hammerschmidt3 introduced the information on gas hydrates to the gas industry and Deaton and Frost4-6 gathered a considerable number of data on the behavior of natural gas hydrates. Recent papers7,8 have extended both the data and the theory of these hydrates. At present, data are available on temperatures and pressures of hydrate formation for pure methane, ethane, propane, n-butane, methane-ethane mixtures, methane-propane mixtures, methane-butane mixtures, and some 15 natural gases, all in the presence of excess water. However, up to the present time no method has been available for predicting the temperature at given pressures or the pressure at given temperatures at which natural gases will form hydrates if saturated with water. This paper pre¬sents data on the methane-propane-water, methane-pentane-water and methane-hexane water systems in four phases, one of which is the hydrate. The application of the phase rule to the methane-propane-water data proves that hydrates behave as solid solutions. The data of this paper and those in the literature were used to develop vapor-solid equilibrium constants,8 which permit prediction of conditions of hydrate formation from the analysis of a natural gas.

Jan 1, 1941

By Frederick Burbridge

The Morning silver-lead-zinc mine of the Federal Mining & Smelting Co. is about 'two miles northwest of Mullan, Ida. The lode is a metasomatic fissure vein. The orebody is approximately 2000 ft. long within the bounds of the property and varies in width from knife edge stringers to 50 ft. It has been developed to a depth of 3600 ft. and stands nearly vertical in Revett quartzite, which .strikes north 65" west. The high-grade veins and lenses are generally mixed with waste (siderite, quartz, and quartzite). The average grade of ore to sorting plant in 1921 was 4 oz. silver per ton, 8.6 per cent. lead, and 4.1 per cent. zinc. Wall rock stands only a short time without timbering. The minimum angle of gravity flow is 45". The ratio of waste sorted out to ore is 6 per cent. No gases are generated underground and temperature has no influence on mining operations. Fresh air is forced down the air raise and up the main shaft. Drifting and Stoping Main drifts 12 ft. wide and 13 ft. high are driven every 200 ft. (vertically) and are connected by raises 125 ft. apart. These raises consist of three compartments (chute, tramway, and timber slide) and are for the purpose of ventilation, access, and hoisting supplies to stopes. Ground is stoped between raises. Chutes are placed every 25 ft. for drawing off ore broken in stopes. Waste for filling is obtained from waste raises off the stope in walls or waste is dumped from the level above down the chute compartment of raises, which is bulkheaded so that waste can be drawn off at any floor as required. Timbering Posts and caps for square sets (varying in diameter from 6 to 24 in.) are cut to length in a sawmill on the surface. No preseratives are used. Timber is taken on a flat car along drifts to a raise nearest the working place and hoisted as required. Practically no timber is salvaged for

Jan 1, 1925

By Donald M. D. Stuart

It gives me great pleasure to accept the invitation I had the honor of receiving through the Secretary of the Institute, to reply to the criticisms made in discussion of the theory advanced in my work entitled, Coal-Dust an Explosive Agent; and to lay before the Institute a further statement of the views which investigations have led me to form upon this subject,

Jan 1, 1897

By Roy C. Kirkman

It is with great pleasure that I read Mr. Howard M. Wells article in the December 1978 issue of MINING ENGINEERING entitled: "Optimization of Mining Engineering Design in Mineral Valuation." Mr. Wells very adequately presents the case and point that there are a great number of variables which must be analyzed during an economic evaluation of an FUND RESOURCE, such as copper or uranium.

Jan 4, 1979

By O. I. Deschon, Ralph Arnold

Deep drilling was the keynote of the more important developments in the North Rocky Mountain region during 1929, with Montana recording the most important achievement through discovery of three new oil fields. Alberta produced 1,000,000 bbl. of 74 gravity naphtha, showing a considerable gain over 1928, developed a commercial oil pool in Turner Valley and extended that field 8 miles southward. Wyoming's discovery field was deepened to a second producing horizon, giving impetus to deeper drilling, and practically every Wyoming oil field will have a deep test either this year or in the near future. Whereas Montana prospecting has been confined to the shallow plains structures, since the discovery of Kevin-Sunburst field, the coming year will see an active search for new oil and gas pools in sharp-dip structures, following the success of prospecting in the Sweetgrass Hills during 1929. A dozen or more structures have been mapped in North Central Montana, several of these straddling the Alberta border. Four structures tested thus far have all shown commercial oil or gas or both. Sweetgrass Hills The first important development in the Hills area was the Rogers-Imperial gasser, which had an initial of 51,000,000 cu. ft. of dry gas per day, with a rock pressure of 1080 lb. This well is located on a sharp nose running north from the hills into Alberta. Several wells drilled by independent operators on the American side, on the west flank of reserve structure, have developed a total open flow capacity of 30,000,000 cubic feet. The third structure tested in the Hills area is known as Bears Den, where commercial oil was found at the base of the Cretaceous at 2470 ft. The existence of oil in three lower sands has been established by two wells on the top of the structure, these two wells finding gas flows of 10,000,000 and 15,000,000 cu. ft., respectively, in the horizon where

Jan 1, 1930