Search Documents

By D. H. Gieskieng

THE advent of curved jaw crusher wearing plates made an approach other than segmental layout analysis desirable for prediction of capacities. For some time it had been known that the drawing board capacities of crushers using these plates had to be considerably modified by complicated experience factors to achieve agreement with results. Because these apparent capacities could be readily increased severalfold by minor crushing chamber shape changes, it was necessary that the utmost precaution be taken in predicting capacities of jaw plates modified for nonchoking, special wear characteristics, or any other reason. To this end the laboratory and field tests outlined by the author in a previous paper1 were made on Blake-type jaw crushers. The results of these tests were summarized in a simple first degree equation applicable to crushers using either straight or curved jaw plates. This equation first outlines the maximum capacity potential of a given crusher, then reduces this figure in accordance with installation circumstances by means of a realization factor. It was found subsequently that this equation, with the addition of an eccentric throw factor, is applicable to standard types of single-toggle or overhead eccentric jaw crushers as far as maximum capacity potential is concerned. However, these crushers have realization factor curves somewhat different from those outlined for the Blake type. While this paper is concerned principally with standard type single-toggle crusher capacities, the evaluation of data obtained with these machines is simplified by comparative reduction to the 10 x 7 in. Blake-type equivalents upon which the summary of the preceding paper was made. Convertibility of data from one type of crusher to the other also tends towards confirmation of both. The agreement of these data is sufficient to be considered complimentary. Consequently the feed factors, f, previously reported for Blake crushers are slightly adjusted to an average with the single-toggle crusher results. Blake-type equation: C = f.d.w.y.t.n.a.r [I] Single-toggle type equation: C = f.d.w.y.t.n.a.e.r [21 where C is the capacity in short tons per hour through the crusher, f is a feed factor, dependent upon the presence of fines in the feed, and the surface character of the jaw plates used. Values of f : Smooth Plates Corrugated Plates With normal fines 0.0000414 0.0000319 Fines scalped out 0.0000368 0.0000252 Large pieces only . 0.0000312 0.0000215 d is the apparent density of the broken product in pounds per cubic foot. (If the true specific gravity of the feed is known, 40 pct voids may be assumed and d becomes 37.4 times sp gr). w is the width of crushing chamber in inches. y is the openside setting of the crusher, in inches. In the case of corrugated jaw plates it is measured from the tip of one corrugation to the bottom of the valley opposite. t is the length of jaw stroke in inches at the bottom of the crushing chamber. It is the difference between open and close-side settings. n is rpm, or crushing cycles per minute, a is the nip-angle factor. It is unity for 26" and 3 pct greater for each less nip-angle degree. A nip-angle of 20" has an a value of 1.18, and an angle of 30" has an a value of 0.88, see Fig. 1. r is the realization factor. It is unity for perfectly uniform choke feeding and usually less for actual operating conditions according to the method of feeding used and the probabilities of hang-ups involving the size of feed and crusher opening. Approximate values are given by the curves in Fig. 2. These values are further reduced by intermittent feeding, e is the throw or diameter of gyration of the single-toggle crusher eccentric in inches. As evident in Fig. 1A, variation of feed size will generally have little effect on nip-angle if both jaw plates have flat areas. Jaw plates having continuous curvature, as in Fig. 1B will have different nip-angles, depending upon the size of feed. For test work as described in this paper this effect was accounted. For general compilation of capacities for average feeds it is suggested that the nip-angle be taken at the various settings computed, at an arbitrary level, such as is indicated in Fig. 1C. Data Evaluation To bring the Blake and single-toggle type crusher capacity test results to common terms for evaluation, all data are converted to terms of 10 x 7 in. Blake-type performance at conditions of 100 lb per cu ft, 10 in. chamber width, 250 rpm, 0.65 in. stroke, 3-in. openside setting, and 18° nip-angle. (The nip-angle of the 10x7 in. Blake is 18° at 3-in. setting.) The single-toggle crusher performances are also divided by the eccentric throw to bring this effect to unity. As outlined,' laboratory and field tests made on Blake-type crushers ranging from 10 x 7 in. to 60 x 48 in. were summarized along the foregoing conditions of speed, stroke, etc. This resulted in groups of data which correspond to feeds with fines, feeds

Jan 1, 1952

By M. C. Leverett, W. B. Lewis

The dynamic behavior of a multiple fluid system is completely describable in terms of driving forces and resistances to flow. The latter are proportional to the viscosity of the fluid under consideration and inversely proportional to a property of the system termed the " effective permeability " to that fluid, a property therefore defined by this relation. Since three phases are usually present in oil reservoirs, it is essential to know the effective permeabilities to the several fluid phases, and the relationship between the composition of the fluid in the pore space and that of the flowing stream, in order to handle satisfactorily certain problems of oil production. In this regard, there are many unknown factors and parameters, and many that can be evaluated only indirectly. However, it is expected that work along lines similar to this present undertaking will help materially in solving these problems. .. . . Previous workers in this field have investigated the two-phase systems, water-gas,' water-oil2 in unconsolidated sands, and water-gasg in consolidated sands. The extension of the study of the flow of heterogeneous fluid systems from two to three phases involved only slight changes in technique. The apparatus used in the present work, except for slight changes to be described, was that used by Leverett in his water-oil experiments.~ Correlation and interpretation of data were made by methods analogous to those used in two- phase work. The relative permeability to a phase—the effective permeability divided by the permeability of the system to a homogeneous fluid—was employed throughout in correlating the rate of flow of that phase with the composition of the pore space. Quantitative measurements of two independent physical properties of the system were required to determine the composition of the pore space. As in the two-phase work, the fraction of water was determined electrically, The gas fraction was determined by measuring changes in volume accompanying measured pressure changes. Suitable account was taken of the solubility of the gas in the liquid phases, and of the vapor pressure of the water phase. Since this work was exploratory in nature, no attempt was made to obtain highly accurate numerical results. Reasonable precision and reproducibility were sought. Experimental Procedure variables Considered.—Of the properties of the fluids, the oil viscosity is most likely in practice to vary widely. Variations in oil viscosity were therefore included in this work, but variations in other properties of the fluids are as yet unexplored. It appears unlikely that the normally encountered variations will produce significant changes. ~h~ observations were made at fairly high pressure gradients, no attempt being made to detect a variation of the relative permeabilities with pressure gradient. It should be pointed out also that since most of the data were taken on one sand size only, it call Only be assumed at present that changes in

Jan 1, 1941

By Richard P. Schoemaker

INTRODUCTION IN underground mining operations the effects of economic and mechanical factors on costs and profits can readily be appreciated and can perhaps be expressed in exact figures and percentages. Less apparent, but frequently more important, is the influence of physical stress. Stress causes failure of supports, collapse of openings, rockbursts, and other damage which directly affects the costs of maintenance, and also to a certain extent the accident rate. Stress can, however, if properly directed, be an aid to mining operations. The caving methods in metal mining and the long-wall method in coal mining are well-known examples. In large-scale mining operations it is almost impossible to neglect stress-control. A better understanding of the mechanism of rock pressure and the application of its principles to practical mining will inevitably lead to a reduction in operating costs. Many theories have been advanced to give the mining engineer a practical outline for stress-control but, although today most experts agree upon the principles of stress distribution around underground openings, there is still no generally accepted theory that explains all phenomena. The main reasons for this incomplete understanding of the problem are the lack of accurate knowledge of the physical properties of rocks under field conditions, and the great complexity of these conditions due to inhomogeneity of the rock, stratification, tectonic disturbances, and many other unknown factors. The research on the rock pressure problems has, however, yielded some valuable facts which, expressed in practical terms, and adapted to local conditions, may become a valuable aid for mining operations. The purpose of this paper is to give a review of the most important accomplishments of this research with respect to the stress phenomena around small underground openings, such as tunnels and shafts, so as to arrive at an outline of the problem as it stands today. Special emphasis is placed on a new theory by the German mining engineer, Rudolf Fenner, which has never before been published or discussed in English. THE PRESSURE DOME THEORY The formation of a dome-shaped space around underground openings is well known from field observations. When openings are made in rock under stress, the rock in the top of the openings will often fail, and caving will continue until the openings have assumed a dome-shaped form, after which equilibrium apparently is re-established. The oldest theory which attempted to explain the phenomenon is the "beam" theory, which postulates that the hanging wall consists of stratified measures that behave as independent beams with fixed ends and a uniformly distributed load. When failure of the beam occurs, inward shearing at the ends will cause the formation of a dome-shaped space. The pressure dome theory, which more or less evolved from the beam theory, merely

Jan 1, 1947

By W. B. Lewis, M. C. Leverett

The dynamic behavior of a multiple fluid system is completely describable in terms of driving forces and resistances to flow. The latter are proportional to the viscosity of the fluid under consideration and inversely proportional to a property of the system termed the " effective permeability " to that fluid, a property therefore defined by this relation. Since three phases are usually present in oil reservoirs, it is essential to know the effective permeabilities to the several fluid phases, and the relationship between the composition of the fluid in the pore space and that of the flowing stream, in order to handle satisfactorily certain problems of oil production. In this regard, there are many unknown factors and parameters, and many that can be evaluated only indirectly. However, it is expected that work along lines similar to this present undertaking will help materially in solving these problems. .. . . Previous workers in this field have investigated the two-phase systems, water-gas,' water-oil2 in unconsolidated sands, and water-gasg in consolidated sands. The extension of the study of the flow of heterogeneous fluid systems from two to three phases involved only slight changes in technique. The apparatus used in the present work, except for slight changes to be described, was that used by Leverett in his water-oil experiments.~ Correlation and interpretation of data were made by methods analogous to those used in two- phase work. The relative permeability to a phase—the effective permeability divided by the permeability of the system to a homogeneous fluid—was employed throughout in correlating the rate of flow of that phase with the composition of the pore space. Quantitative measurements of two independent physical properties of the system were required to determine the composition of the pore space. As in the two-phase work, the fraction of water was determined electrically, The gas fraction was determined by measuring changes in volume accompanying measured pressure changes. Suitable account was taken of the solubility of the gas in the liquid phases, and of the vapor pressure of the water phase. Since this work was exploratory in nature, no attempt was made to obtain highly accurate numerical results. Reasonable precision and reproducibility were sought. Experimental Procedure variables Considered.—Of the properties of the fluids, the oil viscosity is most likely in practice to vary widely. Variations in oil viscosity were therefore included in this work, but variations in other properties of the fluids are as yet unexplored. It appears unlikely that the normally encountered variations will produce significant changes. ~h~ observations were made at fairly high pressure gradients, no attempt being made to detect a variation of the relative permeabilities with pressure gradient. It should be pointed out also that since most of the data were taken on one sand size only, it call Only be assumed at present that changes in

Jan 1, 1941

By J. M. Locke

BRÜCKNER's revolving cylinders for roasting ores, etc., are now used at a number of the mills in Colorado and New Mexico, for the purpose of roasting and chloridizing silver ores, with highly satisfactory results, even from those cylinders of small size, erected before the many improvements of recent date. As examples of the larger improved cylinders, reference can be made to those erected at the Tennessee Reduction Works, Silver City, Grant County, New Mexico, and those which were built, in 1871, at the celebrated Caribou Silver Mill and Mines, Colorado, a mining enterprise which has proved so satisfactory as to have been lately sold to a Holland company for an enormous amount. These cylinders, as now constructed by Messrs. Lane & Bodley, of Cincinnati,, Ohio, are shown in Plate III, in which Fig. 1 is an elevation in perspective, Fig. 2 a longitudinal, and Fig. 3 a trans¬verse section. Fig. 4 is a sketch of a mill, with Brückner's cylinder. The exterior of the cylinder is a shell of boiler iron, 12 feet long by 5 feet 6 inches in diameter. The ends are partially closed with similar material, leaving in the centre a circular opening about 2 feet in diameter, bounded by a flange projecting several inches.. Upon one side is placed an opening closed by a hinged door. Upon the outside of the cylinder are bolted three bands, as shown in Fig. 1, in which the section of the first is square, and that of the third semi¬circular; the second, or middle band, is a strong spur gear. Passing through the cylinder are six pipes parallel to one another, in a plane at an angle of 15° to the axis of the cylinder; these pipes also lie in this plane at an angle of from 30° to 35° to the longitudinal, axis of the plane, as shown in Fig. 2, where the internal arrangement of the cylinder is seen, a perforated diaphragm being formed through part of the cylinder by means of perforated plates placed between

Jan 1, 1874

By M. J. Mullikin, J. B. Conway

for use in describing combined first- and second-stage creep data. In the above ?o represents the instantaneous strain on loading, ?t the limit of transient creep, ?S the steady-state creep rate, t the time, and ? a constant leading to the exhaustion rate of transient creep. It was noted that this equation was similar in form to that proposed originally2 by McVetty. This type of equation was also suggested by Andrade and Aboav3 in studies of the shear strain of cadmium. Calculation of the constants ?o, ?t, ?, and ?s, in Eq. [ l] is somewhat involved due to the slight complexity of this relationship. In the paper by Garofalo a computer approach based on a least-squares analysis was recommended. Such an approach involves a trial and error solution but when a computer facility is available the difficulties in this calculation are of little consequence. It does mean however that the evaluation of this type of equation would become quite tedious if computer facilities were not available. Some recent studies have identified a fairly straightforward method for calculating the constants in the Garofalo equation. While not leading to a least-squares evaluation the approach is accurate and is recom-

Jan 1, 1967

By W. O. Borcherdt

THE 650-ton underground mill of The Empire Zinc Company of Colorado (a subsidiary of The New Jersey Zinc Co.) serves the Eagle mine at Gilman in the Battle Mountain mining district of Colorado, The topography is rough, the mine and mill being under Battle Mountain and the adit entrance in the north wall of the canyon of the Eagle River, which is here a steep gorge. The town of Gilman stands on a shoulder of the mountain at altitude 8975 ft., above sea level, along the Pike's Peak ocean to ocean highway and contains the company office and the usual facilities of a modern mining town. The railway contact is at Belden, altitude 8370 ft., at the bottom of the gorge directly below Gilman, where the westbound track of the Denver and Rio Grande Western Railroad is cut along the north bank and the eastbound track along the south bank of the river. A general description of the mine, mill and service facilities, with an account of the geology, character of the ore and methods of mining and milling having previously been published in a series of articles1, this paper will discuss with as little repetition as practicable the reasons for building the mill underground rather than as a conventional structure, the methods of construction employed and the experiences gained in what is apparently the pioneer plant of this type and extent. There is a large historical background for underground plant construction. From the dim past caves have been used for dwellings, stables, storage and shops. It was natural that where caves were available their many advantages led to their enlargement to suit convenience and where they were not available but the ground conditions, topography and drainage were favorable, to the construction of artificial caves. In the vicinity of Epernay, France, extensive underground chambers protect the manufacture and storage of champagne-an intricate and ingenious application of chemical engineering-and in recent years these plants have been mechanized by the installation of conveyor systems. In the

Jan 1, 1937

By Uwe Neis, K. Peter Kiefhaber

Whereas single particle flotation is considered to be evoked by physico-chemical bubble adhesion, floc flotation seems to be governed by other mechanisms. This study demonstrates that air bubble size does not affect the flotation efficiency of inorganic particles which have been destabilized by different means: 1. addition of simple salts and 2. polyelectrolyte dosage. The air-to-solids ratio A/S does not influence the solids removal efficiency within a broad range of examination. However, there is a significant difference between A/S-values necessary to obtain optimum flotation comparing both destabilization mechanisms. Polyelectrolyte concentration corresponding to complete particle destabilization at the isoelectric point leads to optimum sedimentation rates but not to optimum flotation efficiency. To obtain optimum solids removal by flotation higher polyelectrolyte concentrations are necessary resulting in a positive solids surface charge. These effects are explained on the basis of different floc structures.

Jan 1, 1980

By J. B. Newsom

In the Indiana limestone district, some 50 or 60 per cent of the merchantable stone in a quarry opening is waste, and only about 40 or 50 per cent of the stone from the opening is finally sold. So long as the present system of 'quarrying is used, the wastes measured and reported in this paper will continue. Comprehensive development of an entirely different method of quarrying, using wire saws for cutting, promises great improvement. Some of the savings to be expected are pointed out in the following pages. No attempt has been made to measure losses due to variations and natural flaws in the stone, since these vary greatly in different quarries, and accurate measurement would be difficult. The wastes that have been measured account for about 30 per cent of the total ledge, which leaves 20 or 30 per cent chargeable to unmeasured sources of loss. General Causes of Waste There are four general reasons for quarry waste: (1) the structure of the deposit, such as its shape, bedding planes, solution cavities and strain fractures; (2) efforts to quarry blocks which do not contain distinct color or textural variations; (3) the trade custom which permits purchasers to specify the size of the quarry blocks which they will buy, which is a matter of competition for business on the part of stone producers; (4) quarry methods, which cause the greatest amount of waste. Wide channeler cuts, hook holes, crooked splitting and uneven breaking on quarry floors are included in this category. Waste Due to Structure of Deposits The peculiarities of structure cannot be eliminated, but a chance for saving lies in quarrying to take advantage of them. The commercial deposits of Indiana limestone are lenticular masses from 20 to 70 ft. thick, and nearly horizontal. All of these deposits of good stone are in the Salem limestone, a bed in the sub-Carboniferous. The Salem is traversed by two systems of vertical fractures, a major system running from northeast to southwest and a minor system running from northwest to southeast. Where the stone is covered by an over-

Jan 1, 1932

By John G. Hall

The unstable metal market during 1949, with resulting lower metal prices, has focused every mine operator's attention on the problem of reducing operating costs. Improvement in mining, methods, use of modern mechanical mining equipment, and increasing the efficiency of the labor force are the tools with which we will have to work. Careful planning is necessary to coordinate all phases so that no one phase is overdone. A mine may become over-mechanized if, for instance, capital charges against new equipment exceed the savings in labor costs, or where a large enough tonnage is not produced. The cooperation, of labor is essential to any mechanization program. There have been too many instances where mechanization and improvements have done nothing more than make up for a decrease in labor efficiency, thus bringing the production of labor back to its old standard. The operator has gained little and labor has gained only a "softer job." In any mechanization program there are gains to be had by both the operator and labor. By the efficient application of modern equipment and improved mining methods the operator should gain by decreased costs, and labor may profit by receiving a share of these decreased costs.

Jan 1, 1950

Rooms With Bath Rooms Without Bath Name Location Double Single Double Single Astor Times Square, 43d St. and $5.00 up $4.00 up $4.00 $2.50 up Broadway Belmont 42d St. and Park Ave. 6.00 up 5.00 tip 5.00 3.00 up Breslin 29th St. and Broadway 5.00 up 2.50 up 4.00 up 2.00 up Hermitage 42c1 Street and Broadway 4.50 up 2.50 up 3.50 up 2.00 up Imperial 32d St. and Broadway 4.50 up 3.00 up 3.50 up . 2.50 McAlpin 34th St. and Broadway 4.00 up 3.00 up 3.50 up 2.50 up Manhattan 42d St. and, Madison Ave. 6.00 tip 4.00 up 4.50 up 3.00 up Martinique 32d St. and Broadway 4.00 up 3.00 up 3.00 up 2.00 up Monticello 35 West 64th St. 2.50 up 2.00 up Navarre 38th St. and Seventh Ave 3.00 up 1.50 up 2.50 tip 1.50 up Plaza 58th St. and Fifth Ave. 6.00 up 4.00 up, Prince George.... 28th St. anti Fifth Ave. 3.00 up 2.00 up York 36th St. and Seventh Ave. 3.50 2.50 up 2.50 1.50

Jan 1, 1919

By Charles N. Becker

The practice of drying phosphate in Florida is as old as the industry, which began a little more than half a century ago. The methods, however, have changed considerably. At first, the natural process of exposure to the sun and air was used, later supplemented by wood fires beneath open-air stationary dry kilns and drying towers of various designs. It was not until the early nineties that rotary driers came into use, and at first they were of very small design and fired with wood. As the industry grew and tonnage increased, so likewise grew the number and size of rotary driers, until today the largest installations are 6 ft. up to 7 ft. 6 in. in diameter, and 55 to 60 ft. long, fired with crude oil. The reasons for drying phosphate rock are: (1) to eliminate freight on water in the shipment and (2) to facilitate the good grinding qualities required by the buyers in their acidulation. Phosphate pebbles vary materially in natural characteristics and each property has a direct bearing on the processing. In making comparisons of cost and operating conditions, the following are usually taken into consideration: 1. The hard dense pebbles, which contain very little interior moisture and 6 to 8 per cent total moisture, usually produced from the low-grade deposits. 2. The lighter, porous pebbles, which contain 4 to 5 per cent interior moisture and a total moisture ranging from 9 to 15 per cent. 3. The product of recovery operations using oily reagents, containing from 15 to 25 per cent moisture. 4. The size of the pebbles Usually the plus 5-mesh material is considered as "coarse rock"; the minus 5-mesh plus 24-mesh is "fine rock," and the minute particles below 24 mesh are called "concentrate." 5. The amount of moisture allowed in the dried product. The practice is generally to dry down to 1.5 to 2 per cent moisture. There is, however, an actual range in guarantee of from 1 per cent maximum to 3 per cent maximum.

Jan 1, 1938

By Charles N. Becker

The practice of drying phosphate in Florida is as old as the industry, which began a little more than half a century ago. The methods, however, have changed considerably. At first, the natural process of exposure to the sun and air was used, later supplemented by wood fires beneath open-air stationary dry kilns and drying towers of various designs. It was not until the early nineties that rotary driers came into use, and at first they were of very small design and fired with wood. As the industry grew and tonnage increased, so likewise grew the number and size of rotary driers, until today the largest installations are 6 ft. up to 7 ft. 6 in. in diameter, and 55 to 60 ft. long, fired with crude oil. The reasons for drying phosphate rock are: (1) to eliminate freight on water in the shipment and (2) to facilitate the good grinding qualities required by the buyers in their acidulation. Phosphate pebbles vary materially in natural characteristics and each property has a direct bearing on the processing. In making comparisons of cost and operating conditions, the following are usually taken into consideration: 1. The hard dense pebbles, which contain very little interior moisture and 6 to 8 per cent total moisture, usually produced from the low-grade deposits. 2. The lighter, porous pebbles, which contain 4 to 5 per cent interior moisture and a total moisture ranging from 9 to 15 per cent. 3. The product of recovery operations using oily reagents, containing from 15 to 25 per cent moisture. 4. The size of the pebbles Usually the plus 5-mesh material is considered as "coarse rock"; the minus 5-mesh plus 24-mesh is "fine rock," and the minute particles below 24 mesh are called "concentrate." 5. The amount of moisture allowed in the dried product. The practice is generally to dry down to 1.5 to 2 per cent moisture. There is, however, an actual range in guarantee of from 1 per cent maximum to 3 per cent maximum.

Jan 1, 1938

CONTENTS PAGE DANIELS, SAMUEL, LYON, A. J., and JOHNSON,. J. B.-Casting and Heat Treatment of Some Aluminum Copper-magnesium Alloys 1 ELLIS, O. W. and SCHEMNITZ, D. A.-Experiments on the Heat Treatment of Alpha-beta Brass : 4 ENOS, GEORGE M. and ANDERSON, ROBERT J.-Coatings. Formed on Corroded Metals and Alloys 5 COMSTOCK, GEORGE F.-Notes on the Hardness of Heat-treated Aluminum Bronze 6 Casting and Heat Treatment of Some Aluminum Copper-magnesium Alloys Discussion of the paper of SAMUEL DANIELS, A. J. LYON, and J. B. JOHNSON, presented at the Milwaukee Meeting, October, 1924, and issued, as Paper No. 1350-N, with MINING AND METALLURGY, July, 1924. D. HANSON and M. L. V. GAYLER, Teddington, England (written discussion).-At the National Physical Laboratory, the writers have made a number of researches on the relation between the constitution and mechanical properties of aluminum alloys of various types; the results obtained were in good general agreement with those of the authors. The writers, however, did not think that increasing the copper content of sand-cast low-copper duralumin to 4 per cent. necessarily caused a drop in the elongation to 1.5 per cent., as stated on page 9. In the case of sand-cast copper-aluminium alloys they had obtained much greater elongation, in some cases as great as 13 per cent. in heat-treated castings. For example, in a sand casting containing 3.5 per cent. of copper, a strength of 12 tons per square inch and an elongation of 13 per cent. were obtained; in a casting containing 4.5 per cent. copper, a tensile strength of 13 tons, and an elongation of 9 per cent. were obtained. These values were the maximum; the elongation varied considerably, being as low as 5 per cent. in some cases. In the writers' opinion, such variations are due more to unsoundness in the sand casting than to any other cause.

Jan 1, 1925

By Charles Becker

THE practice of drying phosphate in Florida is as old as the industry, which began a little more than half a century ago. The methods, however, have changed considerably. At first, the natural process of exposure to the sun and air was used, later supplemented by wood fires beneath open-air stationary dry kilns and drying towers of various designs. It was not until the early nineties that rotary driers came into use, and at first they were of very small design and fired with wood. As the industry grew and tonnage increased, so likewise grew the number and size of rotary driers, until today the largest installations are 6 ft. up to 7 ft. 6 in. in diameter, and 55 to 60 ft. long, fired with crude oil. The reasons for drying phosphate rock are: (1) to eliminate freight on water in the shipment and (2) to facilitate the good grinding qualities required by the buyers in their acidulation. Phosphate pebbles vary materially in natural characteristics and each property has a direct bearing on the processing. In making comparisons of cost and operating conditions, the following are usually taken into consideration: 1. The hard dense pebbles, which contain very little interior moisture and 6 to 8 per cent total moisture, usually produced from the low-grade deposits. 2. The lighter, porous pebbles, which contain 4 to 5 per cent interior moisture and a total moisture ranging from 9 to 15 per cent. 3. The product of recovery operations using oily reagents, containing from 15 to 25 per cent moisture. 4. The size of the pebbles. Usually the plus 5-mesh material is considered as "coarse rock"; the minus 5-mesh plus 24-mesh is "fine rock," and the minute particles below 24 mesh are called "concentrate." 5. The amount of moisture allowed in the dried product. The practice is generally to dry down to 1.5 to 2 per cent moisture. There is, however, an actual range in guarantee of from 1 per cent maximum to 3 per cent maximum.

Jan 1, 1936

By F. A. Loving

This paper describes experiments which represent an effort to measure preciscly the pressure-time history in detonating condensed commercial explosives. The performance of explosives in mining has been a favorite subject for experimentalists and theorists for many decades. Much useful empirical information has been developed; but it has not yet been possible to predict, or even to account for, the behavior of explosives in mining on the basis of fundamental physical principals. A basic piece of information that would appear necessary for any rigorous analysis is the pressure-time history in the detonating condensed explosive. The experiments described here represent an effort to measure this relationship precisely in commercial explosives. THE EXPERIMENTAL METHOD The experimental method, first described by Cowan and Jacksonl has been extensively evaluated by Cowan and Balchan for relatively simple explosives. The experimental procedure involves the detonation of a layer of explosive between metal plates whose external surfaces are polished to a mirror finish (Fig. 1). Precise measurements of the deflection of

Jan 1, 1967

By Charles Becker

THE practice of drying phosphate in Florida is as old as the industry, which began a little more than half a century ago. The methods, however, have changed considerably. At first, the natural process of exposure to the sun and air was used, later supplemented by wood fires beneath open-air stationary dry kilns and drying towers of various designs. It was not until the early nineties that rotary driers came into use, and at first they were of very small design and fired with wood. As the industry grew and tonnage increased, so likewise grew the number and size of rotary driers, until today the largest installations are 6 ft. up to 7 ft. 6 in. in diameter, and 55 to 60 ft. long, fired with crude oil. The reasons for drying phosphate rock are: (1) to eliminate freight on water in the shipment and (2) to facilitate the good grinding qualities required by the buyers in their acidulation. Phosphate pebbles vary materially in natural characteristics and each property has a direct bearing on the processing. In making comparisons of cost and operating conditions, the following are usually taken into consideration: 1. The hard dense pebbles, which contain very little interior moisture and 6 to 8 per cent total moisture, usually produced from the low-grade deposits. 2. The lighter, porous pebbles, which contain 4 to 5 per cent interior moisture and a total moisture ranging from 9 to 15 per cent. 3. The product of recovery operations using oily reagents, containing from 15 to 25 per cent moisture. 4. The size of the pebbles. Usually the plus 5-mesh material is considered as "coarse rock"; the minus 5-mesh plus 24-mesh is "fine rock," and the minute particles below 24 mesh are called "concentrate." 5. The amount of moisture allowed in the dried product. The practice is generally to dry down to 1.5 to 2 per cent moisture. There is, however, an actual range in guarantee of from 1 per cent maximum to 3 per cent maximum.

Jan 1, 1936

By W. D. Robertson, R. E. Reed-Hill

Slip on (11221 planes, which do not contain a close-packed direction, has been identified on crystals strained at —190°C. Evidence is also presented to show that (1071) pyramidal slip is a mode of deformation at 25ºC in a limited orientation range. PYRAMIDAL slip (l011) <1120> in magnesium at elevated temperatures has been established for some time.1-2 More recently, Burke and Hibbard reported this mode of deformation at 25ºC, but their results were questioned by Craig.&apos; Also, as far as the present authors know, slip in magnesium on pyramidal planes of the second order, Type II (1122)) has not previously been reported, although Gilman"," identified (1122) slip in another hexagonal metal

Jan 1, 1959

By R. Rocca, M. B. Bever

THE adiabatic elastic deformation of a body is accompanied by a change in temperature. This phenomenon is known as the thermoelastic effect. Under adiabatic conditions the temperature of a metal bar is decreased by an elastic elongation and is increased by an elastic compression. All materials which elongate on heating behave in this manner. The sign of the thermoelastic temperature change is reversed for the few materials which have a negative coefficient of thermal expansion. The following equation for the thermoelastic effect can be derived from fundamental thermody-namic theorems, as shown in the Appendix: dT8 =-a1/cs T dss [1] Cs In this equation, T is the absolute temperature, S is the entropy, a, is the coefficient of linear thermal expansion, cs&apos; is the heat capacity per unit volume at constant stress and s is the stress (positive in tension). Eq 1 can be applied to small, but finite changes in stress in the following form: ?Ts =- a1/cs T?ss [2] The sign of the temperature change AT is opposite to that of the change in stress s for materials which have a positive coefficient of thermal expansion. Eq 2 has been verified for many different materials and stresses at room temperature. No previous publication appears to have been devoted to an in- vestigation of the thermoelastic effect over a range of temperatures. Review of Literature Lord Kelvin (W. Thomson) presented a general theory of the thermoelastic effect in 1851&apos; and later applied it to a solid, subject to an arbitrary system of stresses&apos;. His analysis was based on a cycle of isothermal and constant-strain transformations and led to Eq 2 above. Even today, one of the clearest expositions of the thermoelastic effect is found in Lord Kelvin&apos;s article on elasticity in the Ninth Edition of the Encyclopedia Britannica (1878). R. ROCCA, Junior Member, and M. B. BEVER, Member AIME, are Research Assistant in Metallurgy and Associate Professor of Metallurgy, respectiuely, Massachusetts Institute of Technology, Cambridge, Mass. AIME New York Meeting, Feb. 1950. TP 2760 E. Discussion (2 copies) may be sent to Transactions AIME before APT. 1, 1950, and is scheduled for publication Nov. 1950. Manuscript received Oct. 15, 1949.

Jan 1, 1951

Jan 1, 1954