Search Documents

By F. W. Schroeder

AT the annual meeting of the Institute 2 years ago, a paper,1 " Requirements of Refractories for Open Hearths," was presented by F. W. Davis and G. A. Bole of the U. S. Bureau of Mines. In a brief foreword, D. A. Lyon stated that the paper was not to report the results obtained but rather to present an outline to serve as a basis for discussion. The essential parts of an open-hearth furnace were described and the conditions under which they operate. Some constructive discussion followed the reading of the paper. One of the first fellowship investigations undertaken by the Bureau of Mines in 1924 under the cooperative agreement with Carnegie Institute of Technology, through the Metallurgical Advisory Board, was to determine service conditions of open-hearth refractories. The present paper gives the results of this work which was done in the Pittsburgh district and was in charge of the authors. Material contributions in the form of data were contributed by E. N. Bauer, J. W. Campbell, G. H. Pfeiffer and A. Grodner, Carnegie Institute of Technology research fellows. The study covered 18 mos.

Jan 7, 1926

By S. B. Christy

Jan 1, 1902

[America,-Dear, G. C. Anniston.-Klugh, B. G. Auburn. *Poor, R. S. Bankhead.-Armstrong, W. D. Bessemer.-Creveling, J. G. Lindstrom, W. A. McKenzie, W. C. Mitchell, F. R. Birmingham.-Abbott, C. E. Armstrong, G. R. Austin, W. W., Jr. Ball, T. L. Beard, A. H. Benjamin, F. S. Blackburn, E. C. Blair, A. J. Blair, C. S. Blair. H. W.]

Jan 1, 1946

By M. M. Austin

PURE metallic tantalum, from a practical standpoint, is one of the newer developments in the metal field. Although it was used as filament in incandescent lamps in 1906, only within the last five years has the metal been available in sufficient quantity and suitable form for more general application. In addition to corrosion-resisting properties and high melting point, the metal has an ability to withstand unusual amounts of cold working. It affords some striking demonstrations of block movement during plastic flow.

Jan 1, 1930

By R. G. Davies, R. H. Richman

Several techniques, X-ray diffraction, transmission electron microscopy, conventional, metallography, and mechanical property measurements are combined to investigate decomposition in the suPersaturated solid solution Fe-27 at. pct Be. The following sequence of structures for aging temperatures below 400°C is established: massive short-range order, pseudo-FeBe (L2o) order, Fe3Be (DU3) order, sinusoidal modulation of composition, general or continuous precipitation, and discontinuous or cellular precipitation. In addition to this sequence itself, several features of the individual stages are noteworthy; for example, when coherent modulations occur, their development is parallel to (100) everywhere in the specimen apparently without incubation, and both the wavelength and the composition amplitude of the modulations increase with aging time. Two types of discontinuous reaction are observed, depending upon the aging temperature. At low temperatures (<550°C) the boundary-nucleated variety of discontinuous precipitate predominates; but at higher temperatures (>600°C) the crystallographic variety occurs instead. Hardness and flow-stress measurements clearly reflect the quoted structure sequence. Some qualitative aspects of the structure changes and of the relationship between mechanical properties and structure are discussed. BERYLLIUM in solid solution markedly strengthens iron.&apos;" A recent study demonstrated that not only were supersaturated single crystals of Fe-27 at. pct Be very strong, but they deformed primarily by mechanical twinning.3 Such behavior, coupled with the decrease in solid solubility of beryllium in a Fe from about 33 at. pct at 1165°C to about 10 at. pct at 500°C4 as shown in Fig. 1, leads naturally to questions about property changes with aging in this system. In 1929 roll,1 and later Seljesater and Rogers,5 reported that useful increases in strength could be obtained by aging quenched Fe-Be alloys, but it was not until quite recently that any of the details of precipitation in these alloys were studied. Richman6 observed that both an Fe3Be superlattice (with a DO3 crystal structure the same as Fe3A1, illustrated in Fig. 2) and a modulated structure preceded the appearance of a discrete second phase in the 20 at. pct Be composition. Here, a modulated structure refers to a periodic composition fluctuation within one crystal, while its lattice remains coherent. Subsequent work on a Fe-Be alloys by Heubner7 and von Heimendahl and Heubner8 confirmed the existence of the modulated structure, although only an FeBe (L20) ordered structure was detected (also shown in Fig. 2). Both Rich-man and Heubner corroborated the large increases in hardness during aging reported earlier, but other mechanical properties were not examined. Since modulated systems are encountered relatively infrequently, the influence of coherent modulation upon mechanical properties is not well-known. With the accumulation of information about age-hardening systems, it has become clear that many precipitation reactions cannot always be described by the concept of heterogeneous nucleation at some lattice discontinuity followed by diffusional growth. Rather, complex sequences involving prior "preparation" of the matrix are quite common; that is, a transition structure occurs in the parent phase, instead of in some "nucleus" form. Delineation of such subtle sequences appears to be a worthwhile step toward the understanding of solid-state precipitation. Since not many structural progressions of comparable nature have been reported, the objectives of the present survey are to identify and elucidate the various

Jan 1, 1967

By M. V. Lowry

This paper outlines the economic considerations that led to the recent installation of a thickener at St. Joseph LeadCo.&apos;s Balmat, N.Y. mill. To incorporate storage of concentrates, they decided upon a single, unusually deep tank to be used for both storage and thickening. The abnormally high rake lift required was achieved by the novel feature of having the entire drive platform raise and lower. Initial operating problems are described along with the satisfactory solutions. Total costs for concentrate handling before and after installation of the storage thickeners are compared. In Northern New York State, the St. Joseph Lead Co. conducts a 2100 tpd zinc mining and milling operation at its Balmat Plant. Conventional crushing, grinding, and flotation is used to produce a zinc concentrate. For 32 years, from 1930 through 1962, the plant operated with the concentrates going directly from flotation to the filtering, drying, and loading facilities. All of the concentrate handling equipment, therefore, had to operate 24 hrs per day. It also had to accommodate wide fluctuations in tonnage, due to variations in the grade of ore. Many problems were thereby encountered in filtering and drying, but it was never concluded that the cost could be justified for installing a conventional, large diameter thickener. Finally, in 1963, they installed an unconventional thickener that is unusual in several respects. The tank depth is 16 ft instead of the normal 8 ft. The rakes are raised and lowered by having the main drive gear located on a movable platform. Automatic controls are programmed to raise the drive platform and rakes during one shift of storage. During the next two shifts of withdrawal, the controls are programmed to lower the drive platform and rakes. After three years of operating this unique storage-thickener, the conclusion is that a correct choice was made from several alternative schemes for storing concentrates. The various considerations involved in the final selection will here be analyzed, and the design features and installation details will be de- scribed. Operating problems and modifications made to the equipment will next be considered, and finally the effects upon filtering, drying, and loading will be reported. SELECTION CONSIDERATIONS Even without a thickener, concentrate handling had become reasonably efficient at the Balmat Mill by the year 1962. A tonnage that varied between 6 and 25 tph was being handled fairly satisfactorily. The filter cake moisture of 8%% seemed quite respectable, except that two large filters were usually in service. Three filters often had to be operated in order to prevent excessive filter overflow with consequent loss of values. This situation occurred when zinc concentrates from flotation exceeded 20 tph and when filter cloth blinding developed. Over the years, numerous small improvements had been effected, such as: selection of a filter cloth with better flow characteristics; addition of flocculant to the filter feed; and, in 1953, the smallest of three drum filters was replaced by a five disc, 8&apos; 10" diam filter with a bottom agitator and snap blow. As another example of fairly efficient operation, the oil-fired dryer was doing a seemingly satisfactory job of further reducing the moisture content to an average of 3%. However, there were often considerable dust losses when the tonnage suddenly dropped off to 6 tph. At high tonnage rates, the resulting high moistures of 4% and 5% caused difficulties due to concentrates sticking and freezing in chutes leading to the box car loaders. (Drying of concentrates is justified because of the high freight rate for the long shipping distance to the company owned smelter at Josephtown, Pa. near Pittsburgh.) It was long realized that installation of a thickener would permit the subsequent steps of concentrate handling to proceed more smoothly and would alleviate the problems existing in the filtering, drying, and loading operations. It was also realized that even a slightly lower filter cake moisture could mean considerable savings in fuel oil. However, all these factors were never quite sufficient to warrant the expense of a thickener until three more considerations were added to the picture. First, the advent of flocculants meant that a thickener of relatively small area could now be considered. Secondly, a complete renovation of the zinc flotation circuit was made between 1957 and 1961. The

Jan 1, 1967

By L. D. Clark

Pay-out, the ratio of capital expenditure to annual cash return can be very revealing when employed to gage the merits of a proposed mining venture. It is a quantity, numerically but not physically equal to a factor, by which cash return may be discounted to equal required investment. The fewer the pay-out years, the greater the average annual earning power of the project. Considerable material has been written in the past about the most important and difficult problem mining management faces in evaluation of a property: the optimum production rate for the venture. What daily capacity should be adopted for the proposed operation that it may be the most rewarding to those underwriting it? H.C. Hoover has said, "The most important objective is the least cost per ton mined; and minimum working costs can only be gained by the most intensive production." Theoretically and practically, the quicker the ore is removed, the more profitable should be the venture because of the saving in fixed charges, the consequent lower unit costs and the interest unearned by the profit from the unmined ore. Yet, such performance will be tempered by policy and a restraint imposed by the ratio of capital expenditure to annual cash return. * The &apos;Annual net profit after taxes but including depreciation and depletion allowances. former will be based upon an analysis of the economic climate anticipated, with its many ramifications including the demand for the product, prices, tax laws, the conduct of labor and related wage scales. The variables and intangibles involved in estimating the optimum production rate for a mine do not readily lend themselves to mathematical relationships or equations and the problem can become complex indeed. The more readily applicable and relatively faster appraisal method will be used which, in addition to being reasonably adequate in most cases, will serve as a guide, should a more expanded and detailed estimate be desired. The first question is what is company policy with respect to the rate of investment return? This will depend on that significant period of time referred to as the pay-out, which can be defined as the estimated interval during which capital investment is returned through application of annual cash return to its recovery. Expressed another way, it is the ratio of capital expenditure to the annual cash return. For example, if the capital investment is $C and the annual cash return is $A (after Federal tax), then $C/$A = the pay-out period in years. That is to say, if $C = $1,500,000 and $A = $214,000, then which is the mathematical expression for the period of time it takes to recover the funds originally invested in a mining enterprise. The relationship yp = $C/$A can be useful — an expression which requires only the significant tern yp to be fixed; in other words, the long range investment policy. For what is the pay-out period but an expression of that policy in terms of the speed, within practical limits, with which an individual or company may want to recover capital expenditure? A policy by which pay-out will be fixed is imperative. This ratio must lie within relatively narrow limits governed by what is economically feasible. It cannot be too low, rendering the ratio impractical or absurd, nor too great, delaying the return of capital for reinvestment beyond a commensurate interval. What pay-out will govern this policy? Federal corporate taxes would seem to present the best measure. Consider mining in Canada where new mines are exempt from Federal income tax for 3½ yr from date of first production. This exemption expressly allows The Act states: "A corporation . . . i s not required to include the profits . . . for the period of 36 months commencing with the day on which the mine came into production in reasonable commercial quantites." a company to recover capital expenditure during the early stages of production. With such an incentive, it is logical to strive for as much capital redemption as possible during this period. Thus, 3½ yr would be a major contribution to the pay-out in Canada. Furthermore, it generally takes from 1½ to 3 yr to develop

Jan 1, 1963

By J. T. Burwell

As is well known, the alloys of iron containing 18 ± per cent chromium, 8 ± per cent nickel and less than 1.2 per cent carbon exhibit the same allotropic modifications as iron. The face-centered cubic or gamma phase is stable at high temperatures and the body-centered cubic or alpha ferrite is presumably stable at room temperature. The transformation from the gamma phase to the alpha phase in alloys of the above composi-tion (18-8 or stainless steel) is sluggish; even moderately rapid cooling permits the retention of the gamma phase. Cold-work, however, causes the transformation from gamma to alpha to occur at room temperatures. It is difficult, nevertheless, to induce complete transformation regardless of the method of cold-working. Since metallographic polishing is very effective in transforming the surface austenite to ferrite, as indicated by the magnetic studies of Buehl and Wulff, 1 it was decided to investigate the phenomenon by electron diffraction methods.

Jan 1, 1939

By G. D. Boozer, W. H. Somerton

RESEARCH CORP., LA HABRA, CALIF. Thermal diffusivities of some typical sedimentary rocks have been measured by a rapid unsteady-state technique. Thermal data including diffusivity and conductivity are presented for the temperature range of 200" to 1,800°F. Diffusivities calculated from steady-state conductivity rneasurernents compared favorably with unsteady-state data at the lower temperatures. Unsteady-state data are less reliable at higher temperatures; reported values may be as much as 20 per cent high at temperatures in excess of 1,500°F. This is caused partly by the simplified method used in calculating diffusivity from experimental data and partly by the many thermal reactions which occur at the higher temperatures. The marked decrease in thermal diffusivity and conductivity at elevated temperatures indicates the importance of considering the temperature dependence of thermal properties in subsurface heat-transfer calculntions. Knowledge of the effects of liquid saturation, overburden and pore pressures, and heats of reaction of reservoir materials will be required before complete subsurface thermal analyses may be made. INTRODUCTION Heat-transfer calculations are becoming increasingly important in the analysis of in situ combustion and underground nuclear explosions. Thermal data for natural rock materials at elevated temperatures are generally unavailable. Calculations at high temperatures may be grossly inaccurate if temperature-dependent thermal properties of rocks are not considered. It is known that the heat capacities of rocks increase with temperature. Heat capacities may be calculated from chemical or mineralogica1 analyses of the rock system. Thermal bulk expansion of rocks is believed to be small, although few data are available. Thermal conductivities of most natural rock materials decrease with increased temperature. Thermal diffusivity, defined as the thermal conductivity divided by the product of the heat capacity and the bulk density of the material, is used in unsteadv-state heat-transfer calculations. It is apparent that thermal diffusivity decreases markedly with increased temperature. A new method, which gives a nearly continuous record of thermal diffusivity within the temperature range of 200° to 1,800°F and requires less than 1.5 hours for the run,&apos; was used to measure the diffusivity of several sedimentary rocks. Thermal conductivities were calculated from measured bulk densities, heat capacities calculated from chemical analysis and the measured diffusivity values. Thermal conductivities were measured at lower temperatures by a steady-state technique1 to test the agreement of data obtained by the two methods.

By N. A. Tiner

A study was made of the effects of temperature, type of loading, and electric polarization on the fracturing behavior of copper and zinc coated with mercury. Copper showed an em-brittlement only in cyclic loading, whereas zinc showed an em-brittlenzent in both static and cyclic loading. The embrittle-ment of zinc in static loading was prevented by sub-zero cooling to a temperatzcre of about -70°F. The emhrittlement of both metals was sliglztly reduced by cathodic polarization of mercury. The basic processes involved in fracturing were discussed in the light of these observations. When a solid metal is in contact with certain liquid metals possessing high wetting characteristics, a weakening effect is produced, and the solid metal fractures in brittle manner at a relatively low stress. This lowering of the fracture stress generally is considered different from the stress cracking caused by a corrosive liquid environment and is attributed to the lowering of the solid-liquid interface tension at the grain boundaries.1-4 The purpose of this paper is to describe a number of observations on the special features of fracturing of copper and zinc coated with a liquid mercury film, and to analyze the basic processes involved in fracturing in the light of these observations. EXPERIMENTAL OBSERVATIONS I) Effect of Type of Loading—The evidence appears to indicate that in static loading, metals usually fracture by the initiation of microcracks in the interior preferentially at the grain boundaries or at the intersection of slip bands.&apos; In cyclic loading, cracks develop on the surface within the active slip zones, and gradually propagate with increasing num- ber of cycles.6&apos;7 Because of this difference in the manner of initiation of cracks, a series of bare and mercury coated copper and zinc specimens was subjected to static and cyclic loading, and their fracturing behavior was examined. The specimens were machined to 0.25 in. in diam and 1 in. in length from a high-purity commercial bar stock, and annealed at an appropriate temperature. Mercury was applied to the surface of the specimens by rubbing with cotton wool soaked in a saturated solution of HgCl2 or by etching with a dilute solution of HC1 and rubbing with purified mercury and by washing in water. The static tension load-extension curves were obtained by means of a Riele Screw Power Universal Testing Machine. The room-temperature load-extension curves for copper and zinc are shown in Fig. 1. The deformation behavior of copper, as judged from the general configuration of the load-extension curve, was not affected by mercury coating. The maximum load to fracture and the elongation at the maximum load were practically the same for both specimens. The mercury coated copper, however, showed somewhat less localized necking and had smaller reduction of area than the uncoated metal. The behavior of mercury coated zinc was radically different from the behavior of uncoated metal. The load-extension curves were the same at the

Jan 1, 1962

By Thomas Kesler

THE Cartersville mining district, 35 miles northwest of Atlanta, Ga., has been of varying but continuous importance in the southern mineral industry during the past century. Noted chiefly for its production of brown iron ore, manganese oxide ores, barite, sienna, and magnesian limestone, the district and its environs have produced brick and tile clays, slate, gold, bauxite, and graphitic schist. Minor deposits of serpentine, sericite schist, copper ore, and red iron oxide have been prospected. The obvious deposits of brown iron ore, together with some associated specular hematite, were mined out years ago, although a little ore was left in the workings. Moderately steady production of sienna reached a peak about 1930, then declined rapidly. Manganese mining passed through a relatively active period from the World War to 1931, but has subsided to a small but rather constant output for the Birmingham market. How-ever, the White Manganese Corporation has prepared for possible increased production by constructing a new washer capable of handling about 300 tons of ore per day. Principal activity in the district proper has centered for some years in the production of barite and magne-sian limestone.

Jan 1, 1940

By R. N. Stevens

GRAIN boundary sliding plays a part in the high-temperature deformation of polycrystalline solids, and many investigations1-11 have been carried out to determine the deformation contributed by this mechanism. The principal method employed has been to measure one of the components of the grain boundary displacement, see Fig. 1, at a large number of boundaries, and from the mean value so obtained to calculate the elongation contributed by sliding. A formula connecting these mean values and the elongation contributed is evidently required, and many have been derived. They are usually of the form where Egh is the tensile elongation contributed by sliding, is the mean value of the component, x, N is the mean number of grain boundaries intersecting a line of unit length, and K is a dimensionless parameter known as the averaging factor. Table I summarizes the equations used by various investigators. Examination of these shows that their derivations usually involve doubtful assumptions, and are often in serious error. The purpose of this note is to point out that rigorous solutions to the problem of calculating Egb from x have been available in the literature for some years.&apos; Since this is so little known, and also the original derivations do not make some important points clear, it is proposed to rederive the basic equations. These will be extended further, and the conditions in which the extended equations may be applied will be indicated. The mean values of the components of the sliding vector (I, d, and I:, Fig. 1) will depend on the method by which boundaries are sampled in order to make measurements.3,11 Boundaries are usually sampled by marker lines parallel to the stress axis, or lines perpendicular to the stress axis, the measurement being made at the point where the marker line intercepts the boundary. We will denote the mean values determined by these various sampling methods as follows. lT, dT and vT are mean values obtained by making measurements at pointswhere a transverse line intercepts the boundary while lL, dL, and vl, are the mean values from a longitudinal line. The number of boundaries per unit length also may depend on the direction of measurement, and so we define NT and Nl to be the number of boundaries per unit length, after creep, in the transverse and longitudinal directions, respectively.

Jan 1, 1967

By G. Sachs, E. P. Klier, W. Beck

HYDROGEN embrittlement of steels has recently attracted much attention because it is asso- ciated with a variety of failures, especially those of aircraft structural components.&apos; For instance, one of the undesirable properties of the ultra-high strength steels used for landing gears is their pronounced susceptibility to hydrogen embrittlement during plating. The presence of hydrogen in these steels becomes particularly apparent through delayed or sustained load failures of parts which have been subjected to low loads for an extended time. A number of variables are involved in causing a reduction of strength and ductility through hydrogen

Jan 1, 1957

By A. D. Hughes

A relatively small area in Malaya, about 200 miles long by 40 miles wide, is the most important source of tin in the world. Some tin is recovered in other parts of the peninsula. Of the tin mined, 98 pct is recovered from alluvial deposits. From 1935 to 1941 the average annual world production of tin was 190,000 tons. The average annual production from Malaya during the same period was 62,000 tons or about one third of the total. Other producing countries, in order of importance, were the Netherlands East Indies 34,000 tons, Bolivia 30,000, Belgian Congo, Nigeria, Siam, Burma, China, and a few others with smaller amounts. The serious shortage of tin during the war period was due to the fact that the Japanese were occupying Malaya, Netherlands East Indies, Siam, Burma, and China which, together, formerly were producing 65 pct of the world supply. Because of the importance of tin in the world economy, and because of the fact that little is generally known in this country regarding the methods of recovering the tin in Malaya, it is believed that a short description of the industry, as carried on there, may be of interest to many of the readers. In addition you may be interested in the effect of the Japanese occupation, subsequent recovery of the properties and conditions existing at that time. The Malay Peninsula lies at the southeast tip of Asia. Singapore, a British colony, is situated on a small island at the southern end of the peninsula. It is a city of nearly a million population, an important world port, the site of a large British naval base and of one of the tin smelters. The Federation of Malaya consists of nine states, plus Penang, Malacca, and other small areas formerly part of the Straits Settlements, and it now covers the entire peninsula. The civil administration is controlled by the British. A constitution was adopted recently after reaching agreement with the Malay Sultans of the various states, who retain control of religious matters. The Capital is at Kuala Lumpur, a city of about 200,000 population, 250 miles north of Singapore and about half way to Penang. The country covers an area of 51,000 square miles, an area about equal to that of Florida and about one third that of California. It has a population of about seven million consisting of Malays, Chinese, East Indians, and a relatively small number of Europeans. The principal products are tin and rubber. There are over three million acres of planted rubber. The country is not self-supporting agriculturally as about one third of the necessary food supplies is imported. Rice is the principal food of the Asiatic population and some of the recent unrest is caused by a shortage of rice and the consequent high price. Good highways have been built through the settled part of the country. A railway, Government owned, extends from Singapore northward through the entire peninsula. The climate is tropical but health conditions are good for a tropical country. I was in Malaya from 1939 until January 1942, during the time of the simultaneous air attacks on Pearl Harbor, Manila, Hongkong, and Singa-

Jan 1, 1950

By John W. Gabelman

Uranium exploration technology historically has followed the economic cycle of demand, exploration spurt, and trailing supply; but with a greater lag. Greatest progress was made during the wane of demand as geological investigation caught up with the flood of new discoveries made during relatively short periods of peak demand. Updating brought technology to a new level based on the deposits which were discovered and not on the total range of deposit types which might exist. The technology was seldom able to predict new deposit types or new districts, which have consistently been surprises. Yet each new cycle of increased demand was at a new higher level, occasioned by a new use, which required the discovery of previously unrecognized larger types of deposits. Hindsight shows that data sufficient to have predicted most discoveries were available. The predicted growth of uranium demand far in excess of estimated resources is an incentive to examine current technology for data or promising techniques that might foster discovery by technical prediction rather than by systematic drilling. The world could well be reexamined systematically with new geophysical techniques including gamma spectrometry, radon emanometry, and magnetometry. Known occurrences could well be reevaluated in the light of new data on mineralization process and supergene leaching. Less-leachable extrinsic elements associated with uranium might he sought as clues to unleached uranium at depth. Uranium is increasingly being noted in environments containing coal and petroleum which might become targets. High-temperature replacement disseminations are increasingly reported and particularly attractive as exemplified by the Rossing district. The number of formations containing uranium occurrences is growing so that new, not necessarily fluvial, formations might be productive. Enough drilling has been done to indicate that uranium is selectively distributed regionally under some control yet to be determined. Exploration should address those environments and areas where uranium could occur rather than only those where it is already known.

Jan 1, 1976

By A. W. H. Morris, G. H. Laurie, J. N. Pratt

Using- galvanic cells of the form Sn(liq)/Sn" (LiCl-KC1-SnCl,)/Sn-Ag (alloy), measurements have been made of relative thermodynamic properties of the a, C, E, and liquid phases of the Ag-Sn alloy system. Partial heats of solution of the components in the liquid alloys lzave also been observed by direct cal-orimetric measurement in an isoperibol calorimeter. The thermodynanzic quantities are disczlssed in relation to structural and other properties and the existence of anomalous minor fluctuations in the partial heats and entropies of solution in liquid alloys is tentatively suggested. In the course of a recent electro motive-force study of the thermodynamic properties of Sn-Ag-Pd liquids,&apos; some measurements were also performed on the Ag-Sn binary system. Most previous thermodynamic studies of this system have been concerned with the liquid state. Measurements confined to the limiting heat of solution of silver in liquid tin have been made by many calorimetric workers2 while high-temperature calorimetric measurements of the heats of formation of the full range of liquid alloys are reported in the early work of Kawakami~ (1323°K) and more recently by Wittig and Gehrin~(1248°K). Electromotive-force studies on liquid alloys have been made by Yanko, Drake, and Hovorka&apos; (606" to 686°K; 86 to 99.4 at. pct Sn) and by Frantik and Mc Donald&apos; (900°K; 30 to 90 at. pct Sn). The only known measurements on the solid state are of heats of formation of the a, £, and c phases; these values were obtained using tin-solution calorimetry, at 723"K, by Kleppa,~ whose investigation also yielded heats of formation of liquid alloys containing more than 64 at. pct Sn. The present experiments on the Ag-Sn alloys include a re-examination of the liquid phase and, because of the dearth of free-energy data for the solid state, attempted measurements on the a, c, and E phases. The principal new feature of electromotive-force results obtained for the liquid phase was an indication of anomalous fluctuations in the partial heats and entropies of solution of tin at certain compositions. However, since the values for these thermodynamic quantities were determined from the temperature coefficients of cell potentials, which are commonly subject to considerable error, confirmation by calorimetric measurements was considered desirable. A detailed investigation of the partial heats of solution of the components in the binary liquids was made using a liquid metal solution calorimeter. I) GALVANIC CELL STUDIES a) Experimental Details. Measurements were made, as a function of alloy composition and temperature, of the potentials of reversible galvanic cells of the form: ~n(liq)/~n++/~n-Ag (solid or liquid alloy) Details of the apparatus and experimental techniques have been given elsewhere.&apos; so that a brief account will suffice here. Molten salt, 58 mole pct LiC1-42 mole pct KC1, containing small amounts (1 to 2 mole pct) of stannous chloride was used as the electrolyte. The salts were dehydrated by pre-electrolysis and vacuum -drying techniques. Cells were established under an argon atmosphere by immersing tin and alloy electrodes in the molten salt contained in a large silica tube, heated in a vertical resistance furnace. The tube was sealed at the top by a head plate provided with openings permitting the simultaneous insertion of six electrodes, a central thermocouple sheath, and connections to vacuum and argon lines. Temperatures were controlled to *0.2"C over prolonged periods, with maximum variation over the electrodes at any time of 0.l°C. Temperatures were measured with a standardized Pt/13 pct Rh-Pt couple. The electromotive force of this and the cell potentials were measured on a Cambridge Vernier potentiometer and short-period galvanometer. Alloys were prepared from Pass "S" tin (99.999 pct) and Johnson-Matthey high-purity silver (99.999 pct) by melting in evacuated silica capsules and quenching in cold water. For liquid phase experiments, pieces of the resulting alloys were remelted into prepared silica electrode units, while solid electrodes were prepared by remelting into 3-mm bore tubing, inserting a cleaned molybdenum lead wire, and quenching to produce uniform rods about 3 cm in length, with soundly attached leads. In all cases remelting was done under an argon atmosphere. The solid electrodes were subsequently annealed in evacu ated silica tubes for 14 days at about 20°C below the solidus and quenched. Analyses showed that these techniques produced uniform electrodes with no significant change from weighed out compositions. b) Results and Discussion. Measurements were made on about forty alloys in the solid and liquid states, over varying ranges of temperature between 550" and 1050°K. Stable, mutually consistent, and reproducible electromotive-force data were obtained with most liquid alloys and these are shown in Fig. 1. Investigations were extended below the liquidus tem-

Jan 1, 1967

By N. Nakanishi, C. M. Wayman

The effect of small copper additions on the mar-tensitic transformation behavior in Au-47.5 at. pct Cd was studied by measuring electrical resistivity as a function of temperature. The transformation behavior was found to change and transformation start (M,) temperatures for both the ß to ß&apos; and ß to ß&apos; transformations were depressed substantially by the addition of small amounts of copper. Both M, temperatures were lowered approximately 70°C per at. pct Cu. Copper also had the effect of narrowing the transformation hysteresis region (resistivity us temperature), and for the alloy Au-47.5 Cd-1.5 Cu there was little or no hysteresis; in this alloy, the reverse transfmmation upon heating apparently occurs below the thermodynamic equilibrium temperature, To. THE ß phase in the Au-Cd system occurs at the electron/atom ratio 3/2, and is similar to other ß phases in alloys based on copper, silver, or gold. It is of the CsCl type, in which a considerable degree of long-range order persists to the melting temperature.&apos; The phase boundaries of the ß phase are not known precisely below 300° C, but at room tem- perature the phase exists from approximately 46 to 52* at. pct Cd.2 At low temperatures, the ß phase transforms in a diffusionless (martensitic) manner. Alloys having a composition near 47.5 pct Cd transform upon slow cooling to an orthorhombic3 phase, ß&apos;, at - 60°C. Alloys having a composition near 49.0 pct Cd, transform at - 30°C into a phase, ß", which has been recently identified as trigonal.4 Alloys having compositions near 48.5 pct Cd will transform into both the 0&apos; and 0" phases over a range of temperatures. The progress of transformations can be observed

Jan 1, 1963

By S. LeFevre

THE solution of the housing and sanitation problem in mining communities, keeping in view both economic and humanitarian aspects, demands the best thought of the management of such enterprises. Upon the solution depend the health and comfort of the employee and his family, and as a consequence his contentment and efficiency. The following description covers briefly the methods installed for Witherbee, Sherman & Co. The operation of the system has been for about two years under the direct supervision of T. A. Hammond, Land Agent, and I am indebted to him for a compilation of the results.

Jan 2, 1915

By Ralph Hultgren, Prodyot Roy

Manganese vapor pressures from 1250° to 1500°K were measured by conventional Knudsen and torsion-effusion methods in twelve Fe-Mn alloys with compositions from 9 to 80 at. pct Mn. The Knudsen re-sults agveed approximately with previous measurements found in the literature which indicated the solutions were nearly ideal. However, except for the higher manganese compositions, the initial torsion readings indicated much (up to 50 pct) higher vapor presszcres than the Knudsen method. These high readings decreased steadily with time. The results are interpreted as due to depletion of surface concentration of manganese during evaporation. Thus the initial torsion readings are the most nearly correct and Knudsen methods on alloys are to be regarded with suspicion unless it can be demonstrated that diffusion rates are rapid enough to replenish surface concentrations depleted by evaporation. For the lowest manganese contents and highest temperatures, depletion causes initial torsion readings to be too low. FEW thermodynamic data are available for alloys of the high-melting transition metals due primarily to experimental difficulties at the high temperatures involved. Measurement of vapor pressure is one of the most promising techniques to be applied to this problem. From the vapor pressure of a component of an alloy phase, its activity or its partial molar Gibbs energy can be directly calculated. From measurements over a sufficient range of temperatures and compositions the partial and integral Gibbs energies, enthalpies, and entropies may be determined through Gibbs-Duhem integration. For solid phases of variable composition, which commonly are found in alloys, measured vapor pressures are low because of depletion of the surface concentration of the more volatile component as it is selectively vaporized. Diffusion from the interior tends to restore the depleted concentration. The seriousness of the effect depends on the relative rates of diffusion and vaporization. Although depletion has been recognized as a factor,&apos; direct measurements of its rate are lacking and quantitative estimates of its effect on measurements are uncertain. In the present work the vapor pressures above a series of Fe-Mn alloys have been measured by the torsion-effusion method. This method permits a measurement of the vapor pressure of manganese as soon as the sample comes to temperature and continuously throughout the run. The rate of decline of the apparent vapor pressure measures the rate of depletion and the torsion reading at zero time should be correct. At high manganese concentrations (70 and 80 at. pct Mn), the torsion reading remained nearly constant; surface depletion was negligible. There was a slow drop in measured pressure due to bulk loss of manganese from the sample. However, for lower manganese contents, especially at high temperatures, the depletion effect was considerable and the apparent vapor pressure decreased steadily with time. For these alloys the Knudsen method should give pressures which are too low. The measurement of pressure in the Knudsen method cannot be made until enough manganese has been vaporized to be weighable. The Knudsen result is therefore an integrated average between the initial and final vapor pressures. To verify this, conventional Knudsen measurements were also made with results in approximate agreement with previously published Knudsen measurements for these alloys. As expected, for the lower manganese contents the initial torsion readings of pressure were as much as 50 pct higher than the Knudsen. THE APPARATUS The apparatus, shown in Fig. 1, is capable of operating to temperatures up to 2000°K. A vacuum of 5 x 10"6 mm Hg can be maintained. Temperatures were measured to +3° by a W-Re thermocouple placed in the dummy cell, N. The torsion cell consisted of two alumina crucibles with holes in their covers. They were placed in the molybdenum holder shown suspended from the torsion wire. Rectangular torsion wires (1 by 4 mm) were found to have superior sensitivity and less residual distortion than circular (2-mm-diameter) wires. The precision of angular measurement was found to be *0.025 deg; the variation is no doubt due to temperature fluctuation and vibration. For the Knudsen experiments the alumina cell was set on the support, N. SAMPLE PREPARATION 800-g samples were prepared by melting together electrolytic iron and electrolytic manganese and pouring the melt into a water-cooled copper mold. Melting and pouring were done under a helium at-

Jan 1, 1965

By J. B. Clark, A. J. McEvily, R. L. Snyder

The nonuniform distribution of precipitate particles has been recognized as a leading factor contributing to the relatively low fatigue resistance of aluminum alloys. The structure of many of these alloys is characterized by narrow precipitate-free zones adjacent to the grain boundaries. Alloys with such zones exhibit a tendency for brittle inter crystalline fracture. The interrelation between this type of structure and mechanical properties was investigated in an Al-10 wt pct Mg alloy. It was found that deformation during fatigue occurs preferentially along these zones and cracks initiate there. In Al-10wt pct Mg, the zones were found to be supersaturated even after extensive general precipitation and are due to the absence of proper precipitate nuclei in the region near the grain boundaries. Cold working the alloy prior to aging improves the mechanical properties by inducing precipitation within the zones and also by jogging of grain boundaries. The mode of fracture is changed from brittle inter crystalline to more ductile trans granular fracture. THE process of fatigue is highly structure sensitive, with the strength of the whole often dependent upon some localized discontinuity, either geometrical or metallurgical in nature. Much has been learned about the role of geometrical discontinuities, e.g., notches, in fatigue, but with the exception of the effects of inclusions or the shapes of carbides, relatively little is known about the specific effects of discontinuities in metallurgical structure such as nonuniform precipitation. In most age-hardening aluminum alloys, metallo-graphic studies have shown that the extent of precipitation adjacent to grain boundaries is much less than that which occurs in the interior of the grains. The width of these almost precipitate-free regions, which are sometimes called denuded zones, and the extent of solute depletion within them, are dependent upon the particular alloy and its aging treatment. It has been observed1 that these zones are relatively soft with the result that plastic deformation takes place preferentially within them. It has also been shown 2-4 that there exists a tendency for intercrys- talline cracking in fatigue when such zones are present. It is of interest to note that Broom et al.2,3 were able to reduce the incidence of this type of failure in an A1-4 wt pct Cu alloy by stretching the material 10 pct prior to aging. In the present study, the effects of precipitate-free regions on the fatigue properties of an A1-10 wt pct Mg alloy were studied in detail, and the effects of deformation prior to aging on the nature of the precipitation process as well as on fatigue properties were also investigated. MATERIAL AND PROCESSING An A1-10 wt pct Mg alloy was selected for this study, because it was known that well-defined precipitate-free regions along the grain boundaries are readily obtained in this alloy after aging at 200oC.5 The starting materials were 99.998 pct A1 and singly sublimed magnesium of about 99.9 pct purity. The aluminum was induction melted in a graphite crucible, and then the magnesium addition was immersed until dissolved. Chlorine gas was then bubbled through the molten alloy for 4 min to degas the melt, after which the melt was cast at a pouring temperature of 730" to 760°C into a cold, graphite-coated, tapered steel mold. Since A1-Mg alloys are difficult to homogenize,5 special care was taken to obtain a uniform composition. Two-in. cubes were cut from the ingot and heated at 446°C for 30 min. These cubes were then hot forged approximately 35 pct in each of the three cube directions and homogenized for 16 hr at 446°C. Sheet specimens were then obtained by pressing 40 pct and rolling 35 pct per pass with reheating between reduction steps to a final thickness of approximately 0.10 in. The sheet was then solution treated for 16 hr at 446°C and water quenched. The age hardening behavior of this material at 200°C was then determined, and the results are shown in Fig. 1. The age hardening of this alloy when subjected to cold work prior to aging is also shown in this figure. Preliminary work indicated that extensive deformation after quenching was required to affect drastically the precipitate-free regions in this alloy, and a rolling reduction of 50 pct was chosen. For purposes of comparison the following three conditions were studied: a) Solution treated, quenched, and aged 20 hr at 200°C

Jan 1, 1963