Search Documents

By W. F. Hosford, E. W. Kelley

Deformation studies have been conducted at room temperature on single crystals of magnesium and magnesium alloys with thorium and with lithium. Single crystals oriented to suppress shear on the easily activated basal slip systems were deformed by plane-strain compression. Compression along the C axis was accommodated by {1011} banding. Compression perpendicular to the unconstrained c axis activated {1012} twinning, and, after virtually complete twinning, deformation continued by {1011) banding in the twinned material. Compression perpendicular to the constrained c axis was accommodated by the simultaneous operation of (1012) twinning against the constraint and (1011 ) banding. Although this orientation was favorable for {1010)(1210) prism and {1011}(1~10) pyramidal slip, these modes were not observed in pure magnesium or in Mg-0.5 pct Th. However, {10i0)(1~10) prism slip was observed in crystals of Mg-4 pct Li during compression perpendicular to the constrained c axis. Fracture in all materials occurred parallel to (1124) or {l~il) depending on the orientation and composition of the specimen. THE mechanical behavior of the hcp metals is strongly anisotropic. Although several slip systems have been reported the slip is cpmmonly in the directions of closest packing, the (1210),' and this does not produce strains parallel to the c axis. Hence the inherent anisotropy. The deformation mode most easily activated in magnesium at room temperature is (0001)(1210)- basal slip. Also {1010}(1~10) prism slip and {1011)(1210) pyramidal slip have been reported, primarily at elevated temperatures.2"4 However, at room temperature the shear stresses to activate the prism and pyramidal modes are roughly a hundredfold greater than that required for basal slip.'j4 Thus prism and pyramidal slip may be expected only under special conditions of loading. Strains normal to the basal plane can be produced by twinning, however. Many twinning modes have been reported for magnesium,' with (1012) twinning the most common and relatively easy to activate. Magnesium can deform by (1012) twinning when stressed along the c axis jn tension, but not in compression. In contrast, (1011) twinning is activated by compression along the c axis and not by tension. In addition to primary twinning, secondary twinning or slip can occur within the reoriented material of primary twins.' In general at least five independent shear systems must be active to bring about an arbitrary shape change such as that in the individual grains of a deforming polycrystalline material.' Because basal slip can_ provide only two independent shear systems and (1012) twinning can only accommodate an extension of the c axis, other deformation modes must be active in magnesium for an arbitrary shape change to occur. The purpose of this investigation has therefore been to study the various deformation modes in magnesium at room temperature, with special emphasis on those modes that are less easily activated. The effect of the alloying elements, thorium and lithium, has also been investigated. In polycrystalline aggregates, unambiguous identification of deformation modes is extremely difficult and the direct evaluation of the resolved shear stresses to activate them is not feasible. On the other hand, uni-axial tension and compression experiments on single crystals may not activate some of the- deformation modes because basal slip and/or {1012) twinning cannot be suppressed in most orientations. However, it should be possible to activate all possible deformation modes using oriented single crystals and plane-strain compression. Identification of active deformation systems and evaluation of the resolved shear stresses required to activate them should be facilitated. Wonsiewicz and Backofen have recently completed an investigation of the plasticity of pure magnesium crystals at various temperatures utilizing plane-strain compression and selected crystal orientations. This technique has also been used in the present work. The seven orientations selected for study are indicated in Table I. Plane-strain compression along the c axis (orientations A and B) should activate some deformation mode _other than basal, prism, or pyramidal slip, or (1012) twinning. In orientations C and D, prism or pyramidal slip would be expected to take place. When the compressive load is applied perpendicular to an unconstrained c axis (orientations E and F) the three slip modes should be suppressed but not (10i2) twinning. In orientation G, basal slip should occur.

Jan 1, 1969

By L. N. Cosner, C. F. Austin, J. K. Pringle

Shock wave attenuation studies with three igneous rocks are reported: a spessartite elastic to low intensity stress waves, a diorite which is anelastic, and a porous scoria. The level of shock passing through a given thickness of rock has been determined by donor-receptor methods using high speed streak cameras. Test results include shock propagation velocities adjacent to the explosive, the dependence of test results upon test geometry, and the variation in shock wave attenuation in these three common igneous rock fabrics. The utilization of explosives in rock mediums involves a series of interrelated phenomena. These are the detonation process within the explosive, the transfer of energy from the explosion products to the surrounding rock medium in the form of sound or shock waves, and the transmission of the resulting waves through the rock medium to create damage in the rock mass. The subject of this paper is the investigation of the close-in phenomena that occur in the intensely shocked rock immediately adjacent to a detonating explosive charge. The specific aspects studied include propagation velocities, free surface velocities, pulse attenuations and the determination of the equations of state for the test rocks employed. In addition, a series of tests was conducted to indicate the dependence of the test results on the charge diameter utilized. The equations of state for rock materials have been investigated by a number of authors. Lombard, ',' Grine and Fowles,3,4 Zharkov, 5 Hughes and McQueen,6 Chabai,7,8 and Bass9 have published equation of state data on rock materials similar in structure or composition to those investigated in the study. Rinehart10 has prepared a voluminous tabulation of the available equation of state data from these publications and in addition has included data on many other rock and earth materials in his compilation. The reader is referred to the extensive tabulations and bibliography of Rinehart for classical studies involving the equations of state of metals and other solids and liquids. The problems of sympathetic detonation between drill holes in hard rock environments has received the attention of various authors as have the problems of explosive rock coupling close-in stress wave attenuation and explosive diameter effects. 11 to 18 In particular, the don or-receptor geometry of this report is very similar to the geometry of adjacent drill holes in rock. Most published pulse velocity and attenuation work in rock has been devoted to velocities at much lower amplitudes than those associated with close-in explosives phenomena and most attenuation studies involve transmission and attenuation across large spans of material. Excellent work in these areas has been published by the U. S. Bureau of Mines and by many individuals and groups engaged in geophysical research. SELECTION OF TEST MATERIALS A series of rock materials was desired for this test program that would be meaningful industrially, and that would also yield comparative results from a research viewpoint. Based on the availability of a series of related petro-fabrics, for which there is an abundance of physical and shock response data, three igneous rocks were selected as the test series. The applicability of shock wave studies in igneous rocks to industrial problems is readily demonstrated. Hardrock tunneling, quarrying and mining take place in igneous rocks throughout the world. From a research point of view, igneous rocks exhibit a wide variety of grain sizes and considerable diversity in composition, yet the common igneous rocks have a general similarity in their constituent mineral structures and in their grain-to-grain bonding mechanisms. The latter is based on the concept of rock formation through magma cooling and crystallization, though the degree of liquefaction in granitic plutonic masses is indeed a moot question. Three specific types of igneous rock were chosen for study. A coarse-grained granitic textured rock was desired that would serve as a representative of the widely abundant intrusive rocks of the world and

Jan 1, 1967

By Nicholas J. Grant, A. W. Mullendore

Measurements of grain boundary sliding were made on polycrystal and bicrystal tensile creep specimens of Al-2 pct Mg at 500oand 700oF. Grain and pain boundary orientation factors were studied with respect to their effect on the magnitude and direction of grain boundary sliding. It was concluded that a large part of the observed sliding may be caused by the operation of slip crossing the grain boundaries. Supporting evidence for this model from other investigations is also given. GRAIN boundary sliding in metals during elevated temperature deformation has frequently been thought of as an independent mechanism with its own characteristic stress, temperature, and structure dependence. Further, it is common to regard the grain boundary as the weak link during creep deformation since: 1) the strength of apolycrystallinemetal, as meas-sured by creep rate or rupture life, decreases at\a more rapid rate when sliding comes into action, and 2) grain boundary sliding, as revealed by "boundary darkening" and fold formation is often the first visible deformation. On the other hand, more quantitative observations, in both polycrystals and bicrystals, have shown boundary deformation to be closely related to the over-all deformation of the specimen. The curve of grain boundary contribution to elongation vs time takes a shape similar to that of the total creep curve,',' and the apparent activation energy for sliding appears in most cases to have the same value as that for total creep.3 In order to reconcile these observations, one is left with these possibilities: 1) The grain boundary and grain deformation rates are both controlled by the same rate limiting processes. 2) The rate of sliding is limited by accommodation deformation in the grains. 3) Sliding is the consequence of grain deformation. 4) Grain deformation is dependent on prior grain boundary deformation. Alternatives 2) and 3) would view grain boundary sliding as occurring in series with another deformation process which could be rate controlling. McLean prefers item 3) as the sliding basis,4 where subgrain rotation results from dislocation accumulation in the substructure at the grain boundary. Crussard and Friedel's5 treatment of grain boundary migration considers that dislocations are forced into the grain boundary and are dissociated into dislocations with Burgers' vectors nearly parallel to the grain boundary. The movement of these partial grain boundary dislocations then produces the sliding. The results of this investigation have indicated alternative 3) to be the most appropriate and it is this aspect of grain boundary sliding which will be analyzed. EXPERIMENTAL PROCEDURE Three types of tensile creep tests were employed in this study: (I) A constant load test of one very coarsegrained polycrystalline specimen at 500° F, 3600 psi, 1 pct per/hr strain rate to examine the grain and grain boundary orientation factors in grain boundary sliding. (II) Constant strain rate tests of polycrystalline specimens at 510o and 715o F, 2 pct per/hr strain rate to determine the grain boundary contribution to elongation at very low total strains. (m) Constant strain rate tests of bicrystals of various grain and grain boundary orientations at 500°F, 2 pct per/hr strain rate to obtain further information on the orientation effects in grain boundary sliding. The material used in the tests was a high-purity Al-1'.92 mg alloy, kindly furnished by Alcoa. Its composition is given in Table I. The alloy is a solid solution at the test temperatures. The coarse grained polycrystalline specimen for test (I) was prepared by recrystallizingthe machined specimen, straining it about 1pct intension at room temperature and annealing at 900°F for 8hr. The constant strain rate specimens (11), with an 178 in. sq. by 1/2 in. long gage section, were cut from 1/8 in. thick sheet of cold rolled and annealed (8 hr at 1000oF) material. The latter specimens were supported in a special jig during the milling operations to avoid any bending, and the gage section was subsequently heavily electropolished to remove the cold-worked surface layer. The bicrystals (ID) were machined in the same

Jan 1, 1963

By G. E. Pellissier, C. W. Mason

Tin has long been cited as offering a classic example of polymorphism, second in repute only to the allotropy of sulphul.. The notorious "tin disease," which Cohenl has studied so exhaustively in terms of the enantiotropic transformation of tetragonal white P tin to cubic gray a tin, has apparently encouraged the expectation that one or more additional polymorphic modifications might exist. The search for confirnmntion of this idea has, as might be anticipated, led to the accumulation of a body of miscellaneous evidence, much of which would probably never have been sought, or taken seriously even by its discoverers, but fur previous assumptions. The ball apparently was started rolling iii 1880 by Trechmann,2 who reported a new modification of tin (7 tin), which was brittle and found in "hard head," a highly arsenical, slaggy material produced in a certain stage of tin smelting. A mixture of two kinds of crystals was obtained from a Cornish tin furnace, and those thought to be 7 tin were studied crystallographically. The results indicated that these crystals were rhombic and of different density from the tetragonal tin prepared electrolytically by Miller. Their analysis was given as 98.7 per cent Sn, 1.3 per cent Fe, and traces of As, Sb, Bi and S. In 1881 von Foullon4 obtained similar crystals from a Bohemian tin furnace. Headden5 examined crystals similar to those of Trechmann and von Foullon and reported them to be monoclinic, but of analysis corresponding to stannous sulphide. Later, Stevanovic,~ by goniometric measurements, proved that these crystals of SnS were really rhombic. Groth7 pictures and describes both "rhombic tin" (Fig. 9, vol. 1) ant1 stannous sulphide (Fig. 84, vol. 1); their faces and angles correspond within the accuracy of measurement. Spencers in 1921 examined the above evidence critically; lie lound similar crystals from Cornish tin furnaces, proved them to be SnS, and even was able to analyze some of Trechmann's original specimens, finding high sulphur content. (Apparently Trechmann's analysis had been based on :L second lot of crystals, not described crystallographically.)

Jan 1, 1939

By G. E. Pellissier, C. W. Mason

Tin has long been cited as offering a classic example of polymorphism, second in repute only to the allotropy of sulphul.. The notorious "tin disease," which Cohenl has studied so exhaustively in terms of the enantiotropic transformation of tetragonal white P tin to cubic gray a tin, has apparently encouraged the expectation that one or more additional polymorphic modifications might exist. The search for confirnmntion of this idea has, as might be anticipated, led to the accumulation of a body of miscellaneous evidence, much of which would probably never have been sought, or taken seriously even by its discoverers, but fur previous assumptions. The ball apparently was started rolling iii 1880 by Trechmann,2 who reported a new modification of tin (7 tin), which was brittle and found in "hard head," a highly arsenical, slaggy material produced in a certain stage of tin smelting. A mixture of two kinds of crystals was obtained from a Cornish tin furnace, and those thought to be 7 tin were studied crystallographically. The results indicated that these crystals were rhombic and of different density from the tetragonal tin prepared electrolytically by Miller. Their analysis was given as 98.7 per cent Sn, 1.3 per cent Fe, and traces of As, Sb, Bi and S. In 1881 von Foullon4 obtained similar crystals from a Bohemian tin furnace. Headden5 examined crystals similar to those of Trechmann and von Foullon and reported them to be monoclinic, but of analysis corresponding to stannous sulphide. Later, Stevanovic,~ by goniometric measurements, proved that these crystals of SnS were really rhombic. Groth7 pictures and describes both "rhombic tin" (Fig. 9, vol. 1) ant1 stannous sulphide (Fig. 84, vol. 1); their faces and angles correspond within the accuracy of measurement. Spencers in 1921 examined the above evidence critically; lie lound similar crystals from Cornish tin furnaces, proved them to be SnS, and even was able to analyze some of Trechmann's original specimens, finding high sulphur content. (Apparently Trechmann's analysis had been based on :L second lot of crystals, not described crystallographically.)

Jan 1, 1939

By R. Al-Hussainy, P. B. Crawford, H. J. Ramey

The effect of variations of pressure-dependent viscosity and gas law deviation factor on the flow of real gases through porous media has been considered. A rigorous gas flow equation was developed which is a second order, non-linear partial differential equation with variable coeficients. This equation was reduced by a change of variable to a form similar to the diffusivity equation, but with potential-dependent diffusivity. The change of variable can be used as a new pseudo-pressure for gas flow which replaces pressure or pressure-squared as currently applied to gas flow. Substitution of the real gas pseudo-pressure has a nrtmber of important consequences. First, second degree pressure gradient terms which have commonly been neglected under the assumption that the pressure gradient is small everywhere in the flow system, are rigorously handled. Omission of second degree terms leads to verious errors in estimated pressure distributions for tight formations. Second, flow equations in terms of the real gas pseudo-pressure do not contain viscosity or gas law deviation factors, and thus avoid the need for selection of an average pressure to evaluate physical properties. Third, the real gas pseudo-pressure can be determined numerically in term of pseudo-reduced pressures and temperatures from existing physical property correlations to provide generally useful information. The real gas pseudo-pressure was determined by numerical integration and is presented in both tabular and graphical form in this paper. Finally, production of real gas can be correlated in terms of the real gas pseudo-pressure and shown to be similar to liquid flow as described by diffusivity equation solutions. Applications of the real gas pseudo-pressnre to radial flow systems under transient, steady-state or approximate pseudo-steady-state injection or production have been considered. Superposition of the linearized real gas flow solutions to generate variable rate performance was investigated and found satisfactory. This provides justification for pressure build-up testing. It is believed that the concept of the real gas pseudo-pressure will lead to improved interpretation of results of current gas well testing procedures, both steady and unsteady-state in nature, and improved forecasting of gas production. INTRODUCTION In recent years a considerable effort has been directed to the theory of isothermal flow of gases through porous media. The present state of knowledge is far from being fully developed. The difficulty lies in the non-linearity of partial differential equations which describe both real and ideal gas flow. Solutions which are available are approximate analytical solutions, graphical solutions, analogue solutions and numerical solutions. The earliest attempt to solve this problem involved the method of successions of steady states proposed by Muskat.' Approximate analytical solutions' were obtained by linearizing the flow equation for ideal gas to yield a diffusivity-type equation. Such solutions, though widely used and easy to apply to engineering problems, are of limited value bemuse of idealized assumptions and restrictions imposed upon the flow equation. The validity of linearized equations and the conditions under which their solutions apply have not been fully discussed in the literature. Approximate solutions are those of Heatherington et al.. MacRobertsl and Janicek and Katz.' A graphical solution of the linearized equation was given by Cornell and Katz. Also, by using the mean value of the time derivative in the flow equation, Rowan and Clegg' gave several simple approximate solutions. All the solutions were obtained assuming small pressure gradients and constant gas properties. Variation of gas properties with pressure has been neglected because of analytic difficulties. even in approximate analytic solutions. Green and Wilts8 used an electrical network for simulating one-dimensional flow of an ideal gas. Numerical methods using finite difference equations and digital computing techniques have been used extensively for solving both ideal and real gas equations. Aronofsky and Jenkins"I " and Bruce et al.11 gave numerical solutions for linear and radial gas flow. Douglas et al." gave a solution for a square drainage area. Aronofsky 13 included the effect of slippage on ideal gas flow. The most important contribution to the theory of flow of ideal gases through porous media was the conclusion reached by Aronofsky and Jenkins" that solutions for the liquid flow case'" could be used to generate approximate solutions for constant rate production of ideal gases. An equation describing the flow of real gases has been solved for special cases by a number of investigators using numerical methods. Aronofsky and Ferris 10 onsidered linear flow, while Aronofsky and Porter 17 considered radial gas flow. Gas properties were permitted to vary as linear functions of pressure. Recently, CarteP 18 proposed an empirical correlation by which gas well behavior can be estimated from solutions of the diffusivity equation using instantaneour values of pressure-dependent gas

Jan 1, 1967

By Elmer A. Jones

Like the caboose on the end of a long freight train L made up of mineral and metal processing and consuming industries, the mining industry progresses according to the movement of the train to which it is coupled. Sometimes the caboose rolls smoothly; occasionally it bumps along on the ties; almost always it is under criticism from someone for being too small, too large, too expensive, foolishly progressive, or hopelessly out of date. We who ride in the caboose are used to the rough by now, but it is nice now and then to have a bit of the smooth. Last year the train of industrial production rolled ahead swiftly and smoothly, and, except for a hot-box caused by strikes in copper mines, so did the caboose. As is brought out elsewhere in this issue, the outlook for 1956 is for more of the same.

Feb 1, 1956

By William L. Boyd, Eugene L. McCarthy, Laurance S. Reid

Proper control of the moisture content of natural gas is essential to reliable operation of gas transmission and distribution facilities serving northern markets. The moisture content of natural gas is usually determined by dew point measurement at the existing pressure. For any gas of constant moistrire content. the dew Point varies with the pressure. A correlation of the data of several investigators is prezented in graphical form by the authors. These data were correlated by the authors and F. M. Townsend, C. C. Tsao. M. I). Rogers. Jr.. and J. A. Porter. graduate students in chemi(.a1 engineering at the University of Oklahoma. Of articular interest are the hitherto unpublished low temperature data observed by Wickliffe Skinner. Jr., which are included in this correlation. PRESENTATION OF DATA The problem of interpreting water dew points, or saturation temperatures. of natural gas in terms of specific moisture con-tent has increased in importance during the past decade bec.arl.;e of extensive development.; in the transmission and petro-chemical phases of the natural gas industry. Virtually all gas transported to northern and eastern markets must be dehydrated to a low water vapor content to prevent hydrate formation in transmission and distribution lines and resultant interruption.; in gas deliveries. Complete dehydration is required in certain phases of tile petro-chemical industry involving low-temperature operations. It is a well-known fact that the water vapor content of pure hydrocarbon vapors and their mixtures at superatmospheric pressures cannot be predicted with accuracy by assuming validity of the ideal gas laws." Earlier interest in the general problem was concentrated on the water vapor content of pure hydrocarhons and hydrocarbon mixtures in the pressure and temperature ranges common to gas and oil producing reservoirs in order to obtain fundamental data for the improvement of production techniques and the furtherance of reservoir studies. Excellent data are published for pressures ranging from atmospheric to 10,000 psig and for temperatures ranging from 100° to 460° F4,9,10,11 and are found to be in close agreement. However, experimental data at high pressures and temperatures below 100°F are comparatively limited in scope. Experimental data in the lower temperature range have been reported by Laulhere and Briscoe.8 Deaton, et al,2,3 Hammerscllmidt,5,6 and wade," In general, the pressures employed in these investigations ranged from atmospheric to 1.000 psig while temperatures ranged from 32° to 120°F; i.e., the usual conditions encountered in gas transmission line operations, Additional data were reported by Russell, et al,12 at pressures as high as 2.000 psig and covering a rather narrow atmospheric temperature range. In 1947, Hammerschmidt published a correlation of all available data,' in which the water vapor content of gases at saturation. under high pressure and low temperature. was predicted by extrapolation. In 1948, Wickliffe Skinner. Jr.. presented data on the moisture content of a low nitrogen content gas at low temperature and at pressures ranging upward to 1.500 psia.1-3 Comparison of Skinner's experimental data with the extrapolated data of Hammerscllmidt revealed an appreciable variation in the lower temperature range. emphasizing the need for a new correlation which would rely on Skinner's data at lower temperatures. Careful scrutiny of available data suggested that presence of an appreciable quantity of nitrogen in a gas mixture may affect its saturated moisture content so that data obtained from gases with more than three per cent nitrogen were not used in this correlation. CORRELATION OF DATA Data employed in this correlation are presented in Table I. The data of Dodson and Standing.4 McKetta and Katz,9 and Olds, Sage and Lacey10 were compared and found to be in close agreement so that the data of Olds. et al, re-plotted in a more convenient form by the Humble Oil and Refining Co.,' were used for temperatures of 100°F and above. Skinner's data were used for temperatures below 40°F. Between these intermediate temperature limits, the data of Hammerschmidt.7 Wade" and extrapolated data of Olds. et al.1 were tabulated

Jan 1, 1950

By Walter Renton Ingalls

Metallurgical literature has no record of any ore beneficiated for cadmium alone, and the cadmium of commerce is derived from zinc ore, with which cadmium is generally associated. Zinc ores free from cadmium—e.g., the ores of the Franklin and Stirling mines, New Jersey, and of Broken Hill in Rhodesia—are rare. Blende concentrates of 50 to 60 per cent grade have contained (in production of important tonnage) as much as I per cent Cd, which is unusually high. The concentrates from the Tri-State district average from 0.3 to 0.4 per cent Cd, which is high. The concentrates from mines west of the Rocky Mountains seldom are higher than 0.2 per cent. In the periodic system of the elements, cadmium is in the same group with zinc. Its properties and compounds are similar. Its metallurgy is also similar. Cadmium has a melting point of 320°C. and a boiling point of 778"C., while the melting point of zinc is 415'C. and the boiling point gos°C. These conditions, together with the lower reduction temperature of cadmium oxide, indicate means for. separating cadmium from zinc. Cadmium in spelter is viewed, if not as an impurity, at least as an alloying element that may be objectionable, its special effect being hardening. However, for some purposes, a little cadmium in spelter is desired, and 0.4 per cent may be permissible, even in spelter for rolling. Cadmium in spelter for brassmaking is completely volatilized at the temperature of that process, and in bygone days an immense quantity of cadmium must have been lost in the fumes from these furnaces. Pyrometalltjrgy—Early Cadmium compounds, sulphide and oxide, being more volatile than the corresponding compounds of zinc, loss of cadmium begins to occur from the first furnace operation. In normal roasting, even with Tri-State ore, this loss may not be very high. Raw ore, assaying 0.4 per cent Cd, may be expected to give a roasted product of the same assay, which would imply a cadmium loss of about 15 per cent. Roasted ore, assaying 0.4 per cent Cd when distilled at ordinary furnace temperature, yielded spelter containing about half of that in the ore charged. The first draw of spelter under these conditions may assay 0.8 per cent Cd (accounting for 22 per cent of the cadmium recovery) and after the several draws of spelter have been equalized the cadmium content may average 0.35 per cent. If, therefore, 2000 lb. of blende averaging 0.35 to 0.4 per cent Cd is roasted and distilled, there may be obtained 1000 lb. of spelter, assaying 0.35 per cent Cd or 3.5 lb. content, which entering into Prime Western spelter will be sold at the spelter price. It will be observed from the outline hereinbefore (summarizing conditions prior to the introduction of sintering) that the main loss of cadmium occurred in the distillation process and by failure to condense, which could be ameliorated by attaching a prolong to the condenser, thus collecting

Jan 1, 1944

By J. W. Spretnak, V. Kandarpa

Stress -induced ordering of carbon atoms is studied in a series of Fe-Mn-C alloys. A prominent peak is found in the vicinity of 280°C at frequencies of the order of 1.0 cps, with an associated activation energy of 37 kcal per mole. The height of the peak is linearly rekzted to the concentration of carbon in solution. The distortion of octahedral holes by manganese atoms appears to be predominant over carbon-carbon pair interactions. RELAXATION by stress-induced ordering of point defects is expected whenever the introduction of these point defects produces distortions which have a lower symmetry than that of the lattice. Under zero stress, the isolated point defects occupy the crystallographic-ally equivalent positions in the lattice, as these represent states of equal energy. However, if the defect sites are asymmetric, application of an uniaxial stress will split the energy states, and a redistribution of the defects among various states will take place. This is the case of the internal friction peak called the Snoek peak,1 resulting from isolated interstitials in bcc metals. The interstitial sites in this case have tetragonal symmetry. In the case of fcc and hcp lattices, such an effect is not expected from isolated point defects because of the symmetrical nature of the interstitial sites. However, internal friction peaks arising from interstitial diffusion have been reported both in hcp2,3 and fcc4-8 lattices. These peaks are often explained on the basis of stress-induced ordering of interstitial solutes, caused by the deviation of interstitial sites from their cubic symmetry through the presence of nearby defects. In the case of fcc lattices, evidence for interactions of both the substitutional-interstitial4,6,13 and interstitial-interstitial types5'798'14 have been presented by various investigators. The purpose of the present investigation was to study the internal friction peak attributed to the diffusion of interstitial carbon atoms in high purity austenitic manganese steels and to account for the peak in the light of the existing models. MATERIALS The Fe-Mn-C alloys used in the present investigation were made in two different ways, designated as Type I and Type 11. Type I alloys were made from high purity Fe-Mn alloys obtained in the form of 0.04- in.-diam wires from Materials Research Corporation, Orangeburg, N.Y. These alloys were carburized to different levels using gas mixtures of H2 and CH4 at 1000°C. Type I1 alloys were made in this laboratory starting with zone refined iron, spectrographically pure manganese, and spectrographically pure carbon. They were melted in an argon arc melting furnace and drawn into 0.04-in.-diam wires. All the wires were annealed at about 900°C for 3 hr prior to the internal friction experiments. After the measurements of internal friction, the phases in the samples were identified by X-ray diffraction and the carbon determined by the combustion method. EXPERIMENTAL PROCEDURE In the present work, a classical Ke-type pendulum was used. The details of the equipment were described previously by D. T. Peters.9 Dry helium at 40 torr was used in all the experiments. The internal friction, measured as the logarithmic decrement of the torsion amplitude of vibration was determined as a function of temperature, from ambient to about 500°C. The background internal friction was assumed to have the form of the exponential of the inverse temperature and was subtracted from the raw data. The height of the peak was measured at the position of the maximum in the plot of the internal friction versus temperature. The activation energies of the peaks were measured by the peak shift method. The internal friction values for an alloy were obtained as a function of temperature at different frequencies of vibration. The position of the peak changes with frequency, the higher the frequency the higher the peak temperature. The activation energy of the process associated with the peak is obtained using the formula

Jan 1, 1970

By Bailey Willis, George Otis Smith

I. Summary of General Features. Location.—The Clealum iron-ore deposits occur on Clealum river, a tributary of the Yakima river; in the eastern spurs of the Cascade range, Washington.† Mount Stuart, 9470 feet in altitude, is a dominant peak of the district, which will therefore be referred to as the Mount Stuart district. By way of the valley and cañon of the Clealum, the ores are 18 miles from Roslyn, the colliery-town, which is reached by a short branch from the Northern Pacific Railroad. Where they occur the valley has an elevation of 2900 to 8000 feet above sea; that of the end of the branch railroad at Ronald is 2345 feet. The grade of the valley from near Ronald to the junction of the Clealum and Salmon Lasac rivers, 144 miles, is 20 feet per mile; thence to the iron-ores it is 130 feet per mile, through a cañon 241/2 miles long. Abreast of the deposits the western wall of the valley is formed by precipices of sandstone; the eastern slope is comparatively gentle, being cut in easily eroded

Jan 1, 1901

Contents A - Metal Mining B - Minerals Beneficiation F - Coal H - Industrial Minerals I - Mining Geology L - Geophysics

Jan 11, 1953

By Richard E. Chism

SAN DIMAS, in the State of Durango, Mexico, on the frontier of the State of Sinaloa, is the centre of an extensive and rich mining region, which has been exploited for over a hundred years; and the patio process for working silver ores has there attained the highest perfection of which it is capable. Local modifications have been engrafted upon the underlying principles of the process, but, as a whole, the San Dimas practice so fully illustrates its typical capabilities, that I have undertaken to describe its workings in the hope of lightening, to some degree, the labors of my professional brethren who may have occasion to visit Mexico." As is tolerably well known, the patio process, like all other systems of free amalgamation, is not successful with ores containing more than a trace of zinc or lead, the presence of zincblende being especially obnoxious. Iron and copper in small quantities are not particularly disadvantageous. The process succeeds very well with all sulphide ores which do not contain much more than a trace of arsenic and antimony, provided the tailings are concentrated, although, of course, it is best adapted for free milling ores. For suitable silver ores that contain small amounts of free gold the process is still a good one, but where the gold is combined with sulphurets, a considerable and even an excessive loss is inevitable. Hitherto the Mexicans have submitted to this loss, but, since the introduction of American mills, they are gradually abandoning the patio process in favor of the other. The San Dimas ores have a gangue of quartz and feldspar. They are composed principally of silver sulphides, with some chloride and

Jan 1, 1883

By E. C. W. Perryman

The recovery of X-ray line broadening, hardness, and electrical resistivity from cold worked AI-Mg alloys has been investigated. The results, together with those from density measurements, suggest that magnesium atoms freeze in the excess vacancies formed by cold working, and that this affects the climb of dislocations during the recovery process. PREVIOUS work1, " has shown that while 1 pct Mg increases the activation energy for recrystalliza-tion, it decreases the activation energy for the recovery of mechanical properties and decreases the subgrain size both after cold working and annealing. A similar result has been reported by Varley2 for an A1-2 pct Mg alloy. With plastic deformation at high temperatures, McLean and Farmer' and Rachinger have found that magnesium appears to retard the motion of dislocations and, furthermore, they find little or no effect of magnesium on the size of subgrains formed during high temperature deformation. In view of the apparent contradictions as to the effect of magnesium on subgrain size, the recovery process in Al-Mg alloys has been investigated more thoroughly by studying the annealing out of X-ray line broadening, hardness, and electrical resistivity from alloys cold worked at room temperature. Material Used—The chemical analyses of the alloys are given in Table I. Fabrication—The material used was cold rolled 20 pct at room temperature, the grain size prior to the last cold rolling operation being similar to that used in previous work; i.e., 230. The experimental procedure for annealing, determination of X-rav half-veak breadth. hardness measurement, electEica1 resistivity, and density and metallographic examination was exactly the same as previously described." Variation of X-Ray Half-Peak Breadth with Annealing Time—Isothermal annealing curves at 100°, 200°, and 250°C were obtained for material cold worked 20 pct. The half-peak breadth of the (333) Ka, line directly after cold working is shown as a function of magnesium content in Fig. 1. Only with the 2.87 pct Mg alloy was overlapping of the a, and n.. reflections observed to any appreciable extent. To separate these, Rachinger's method' was used. Typical isothermal annealing curves are shown in Figs. 2 and 3 for 100" and 200°C, respectively. These curves are similar to those obtained previously for super-purity aluminum except that the

Jan 1, 1957

By R. N. Upadhyay, M. Maleki, I. Fatt

Conventional laboratory core analysis tests on samples of two limestone reservoir rocks indicate that about 20 per cent of PV is in dead-end pores. These tests (electric logging formation factor, mercury injection capillary pressure and miscible displacement) were carried out on 1/4-in. diameter test plugs. Test results show a clear dilference between these samples and sandstone or homogeneous limestone reservoir rock. Although the amount of dead-end pore space can be only roughly estimated, the presence of such pore space seems clearly indicated. Pressure transient studies also show presence of deadend PV. Although they do not give quantitative results, pressure transient data yield a reasonable estimate of the size of the neck connecting dead-end pores to the main flow channels. INTRODUCTION Equations conventionally used to describe reservoir flow behavior contain the implicit assumption that all connected pore spaces contributed to both porosity and permeability. Several authors3-7 have pointed out the changes in pressure transient behavior and in electric log interpretation that may result if this assumption is incorrect and, instead, dead-end or cul-de-sac pores are present. There is a need for laboratory tests that can detect presence of dead-end pores in core samples. With such information on hand the petroleum engineer can make more rational use of the mathematical tools now available for analysis of reservoir flow behavior. This paper describes laboratory studies designed to detect and, if possible, give a quantitative measure of dead-end PV in laboratory-size core plugs. Three reservoir rocks were used, two of which were limestones suspected of having deadend pore spaces and a well-known sandstone, used as a comparison standard, in which there is believed to be little or no dead-end pore space. All the studies were designed to measure the natural dead-end PV; i.e., the pore space which is dead-ended because of rock structure. During multiphase flow in a rock without dead-end pores, some parts of one of the phases can become surrounded by the other, thereby giving (for certain flow behavior) an effective dead-end pV8,9. Such behavior will not be described here.

Jan 1, 1967

By C. D. Broadbent

INTRODUCTION The slope stability research plan at Kennecott was developed to serve the specific needs of large, open pit mines; primarily those developed in faulted and highly-fractured intrusive deposits. The program emphasis is on applied research; being defined in this case as research into the engineering mechanics of discontinuous rock and into the related rock property survey and slope design techniques. The program has been developed in phases, with each phase organized to explore more thoroughly the most significant findings of previous work and to improve on techniques found to be applicable. The current work is based on principles developed early in the program and that show promise of having engineering and economic value. A brief summary of the conceptual principles of the program is given to put our current work in context. This is followed by a review of the two cooperative programs done with the U. S. Bureau of Mines. Most recent work is described and interpreted in terms of practical slope design. Although failure-free slopes are a desirable goal, it is recognized that some failures will occur when overall slope designs approach a calculated safety factor of one. A discussion of failure control research is therefore offered. BACKGROUND In 1965 Kennecott management specified that a slope stability technology must be used to achieve optimum development of ore resources. The subject was carefully explored and by 1960 it had been established that there was no technology readily applicable to open pit slope design. Therefore, in 1962, Kennecott Copper Corporation and the U. S. Bureau of Mines agreed upon a cooperative research program having the objective of developing a mine slope stability science. One of the first decisions made by the cooperating groups was that the research must be conducted primarily in the field and not in the unrealistic environments of a laboratory. Accordingly, the Kimbley Pit, an abandoned mine once operated by Kennecott's Nevada Mines Division in Nevada, was selected for the full-scale research. Fortunately, there was near-universal agreement on the basic stability parameters and thus on the areas to be investigated. These parameters were acknowledged to be: (1) anisotropy (generally due to faults or joints), (2) stress, and (3) water; in that order of importance.

Jan 1, 1972

By Marcel Daly

THE writer has devoted a number of years to practical operations and to the study of geology in the oil fields. In consequence, he has been brought to investigate the theories advanced to account for the accumulation of oil and gas in commercial deposits. It is the result of these investigations and his personal conclusions that he wishes to sum up in this paper. The writer is an advocate of the organic origin of petroleum found in pools. He has been led to believe that the present theories of oil and gas accumulations are incomplete and, in certain respects, incorrect, although they may embody certain elements of truth; that the forces that are called upon to explain the movement are only secondary forces in the process, and insufficient, by themselves, to cause this movement; and that the phenomenon of accumulation is of much larger order than heretofore admitted and bears an intimate relation with the general as well as with the local deformations of the crust and is a direct consequence and a mechanical effect of these deformations to which the term "diastrophic" has been applied. As a complement to this theory, the writer offers a new interpretation of the "rock pressure" and of the mechanism of the "sealing up" of this pressure in oil and gas pools.

Jan 7, 1916

By Aureal T. Cross

THIS paper is a review of the published literature on research in coal geology, principally exclusive of resource studies, which appeared or became available during 1950 and the latter part of 1949. This report is not to be construed as being complete. The papers referred to in the bibliography are those among many more, which were read either in full or in abstract. Undoubtedly other papers were published which either escaped the author's notice or were not available to him. Those which were seen in abstract only (about one fourth of those listed) were not available in time for the inclusion of more than a notice. An outline of all papers listed in the bibliography has been arranged by subjects and reasonable subdivisions with some papers cited under more than one subject. Most papers are indexed according to the principal subject of discussion or research only as to an unusual or noteworthy section of the entire report. There will likely be some disagreement as to the quality or merit of some of the papers selected and the specialist may be supercritical of the outline or organization of papers in his field. It may be that attention has occasionally been drawn to papers reporting old information or conclusions of questionable value. Conferences and Meetings One of the best indications of the growing interest in coal geology problems in the United States is the increasing number of times this field has been the focus of attention at conferences and meetings. Notable among these are the joint meeting of the Society of Economic Geologists and the Geological Society of America at El Paso, November 1949, at which the principal thesis was concerned with low rank carbonaceous fuel deposits, especially of western United States. Among the papers given which are already available were those presented by Barghoorn,'" Parry? Roe? and Parks."' At the annual meeting of the Botanical Society of America in New York, December 1949, a joint meeting of the Paleobotanical and Microbiological Sections was held for which a symposium on Microbiology in Relation to the Geologic Accumulation of Organic Complexes was organized. Publication of the six papers presented by Ralph G. H. Siu, Elso S. Barghoorn, Irving Breger, Claude E. ZoBell, James M. Schopf, and A. C. Thayson is anticipated. At the regular meetings of the Paleobotanical Section at the same time, several other papers of interest reported on coal ball studies, partial coalification of petrified wood, and floras. In Chicago, April 1950, a symposium on Applied Paleobotany was held by the Society of Economic Paleontologists and Mineralogists in conjunction with the American Association of Petroleum Geologists. The five papers presented at this meeting dealt with the use of Paleozoic plant microfossils for stratigraphic work, J. M. Schopf, Devonian-Missis-sippian fossils of the black shales, Aureal T. Cross, Mesozoic plants of stratigraphic value, Th. Just, plant microfossils of the Tertiary, L. R. Wilson, and studies of the Brandon lignite, Elso S. Barghoorn. Early publication of these in the Journal of Paleontology is expected. The Nova Scotia Research Foundation and the Nova Scotia Dept. of Mines sponsored an excellent 3-day conference in June 1950, which dealt with several aspects of coal geology. Papers on coal classification, P. A. Hacquenbard, structure and sedimentation problems in Nova Scotia, T. B. Haites, new techniques of thermal analysis, W. L. White-head, geochemical investigations of Nova Scotia coals, Irving Breger, the role of fossil plant spores in coal correlation and the stratigraphy of the coal-bearing strata of the Appalachian Region, Aureal T. Cross, were given. Some discussions of these papers by those in attendance were recorded, and the entire proceedings is being prepared for publication. In September 1950, an unusual 3-day field conference was held by the Ohio and West Virginia Geological Surveys under the sponsorship of the Coal Geology Committee. This study of the stratigraphy, sedimentation, and nomenclature of the Upper Pennsylvanian and Permian coal-bearing strata of southeastern Ohio, southwestern Pennsylvania, and northern West Virginia was augmented by two discussions on associated rocks (clays and shales) and stratigraphic nomenclature at Wheeling and Morgantown, West Va. An extensive guidebook was prepared, and transcriptions of the Morgantown meeting were made. As a follow-up of the September field conference, a round-table discussion was held on this general topic at a special open meeting of the Coal Research Committee in conjunction with the November meeting of the Geological Society in Washington. Short prepared statements to invite discussion were given on each of several topics by L. M. Cline, Carl 0.

Jan 1, 1953

By Aureal T. Cross

THIS paper is a review of the published literature on research in coal geology, principally exclusive of resource studies, which appeared or became available during 1950 and the latter part of 1949. This report is not to be construed as being complete. The papers referred to in the bibliography are those among many more, which were read either in full or in abstract. Undoubtedly other papers were published which either escaped the author's notice or were not available to him. Those which were seen in abstract only (about one fourth of those listed) were not available in time for the inclusion of more than a notice. An outline of all papers listed in the bibliography has been arranged by subjects and reasonable subdivisions with some papers cited under more than one subject. Most papers are indexed according to the principal subject of discussion or research only as to an unusual or noteworthy section of the entire report. There will likely be some disagreement as to the quality or merit of some of the papers selected and the specialist may be supercritical of the outline or organization of papers in his field. It may be that attention has occasionally been drawn to papers reporting old information or conclusions of questionable value. Conferences and Meetings One of the best indications of the growing interest in coal geology problems in the United States is the increasing number of times this field has been the focus of attention at conferences and meetings. Notable among these are the joint meeting of the Society of Economic Geologists and the Geological Society of America at El Paso, November 1949, at which the principal thesis was concerned with low rank carbonaceous fuel deposits, especially of western United States. Among the papers given which are already available were those presented by Barghoorn,'" Parry? Roe? and Parks."' At the annual meeting of the Botanical Society of America in New York, December 1949, a joint meeting of the Paleobotanical and Microbiological Sections was held for which a symposium on Microbiology in Relation to the Geologic Accumulation of Organic Complexes was organized. Publication of the six papers presented by Ralph G. H. Siu, Elso S. Barghoorn, Irving Breger, Claude E. ZoBell, James M. Schopf, and A. C. Thayson is anticipated. At the regular meetings of the Paleobotanical Section at the same time, several other papers of interest reported on coal ball studies, partial coalification of petrified wood, and floras. In Chicago, April 1950, a symposium on Applied Paleobotany was held by the Society of Economic Paleontologists and Mineralogists in conjunction with the American Association of Petroleum Geologists. The five papers presented at this meeting dealt with the use of Paleozoic plant microfossils for stratigraphic work, J. M. Schopf, Devonian-Missis-sippian fossils of the black shales, Aureal T. Cross, Mesozoic plants of stratigraphic value, Th. Just, plant microfossils of the Tertiary, L. R. Wilson, and studies of the Brandon lignite, Elso S. Barghoorn. Early publication of these in the Journal of Paleontology is expected. The Nova Scotia Research Foundation and the Nova Scotia Dept. of Mines sponsored an excellent 3-day conference in June 1950, which dealt with several aspects of coal geology. Papers on coal classification, P. A. Hacquenbard, structure and sedimentation problems in Nova Scotia, T. B. Haites, new techniques of thermal analysis, W. L. White-head, geochemical investigations of Nova Scotia coals, Irving Breger, the role of fossil plant spores in coal correlation and the stratigraphy of the coal-bearing strata of the Appalachian Region, Aureal T. Cross, were given. Some discussions of these papers by those in attendance were recorded, and the entire proceedings is being prepared for publication. In September 1950, an unusual 3-day field conference was held by the Ohio and West Virginia Geological Surveys under the sponsorship of the Coal Geology Committee. This study of the stratigraphy, sedimentation, and nomenclature of the Upper Pennsylvanian and Permian coal-bearing strata of southeastern Ohio, southwestern Pennsylvania, and northern West Virginia was augmented by two discussions on associated rocks (clays and shales) and stratigraphic nomenclature at Wheeling and Morgantown, West Va. An extensive guidebook was prepared, and transcriptions of the Morgantown meeting were made. As a follow-up of the September field conference, a round-table discussion was held on this general topic at a special open meeting of the Coal Research Committee in conjunction with the November meeting of the Geological Society in Washington. Short prepared statements to invite discussion were given on each of several topics by L. M. Cline, Carl 0.

Jan 1, 1953

By R. E. Zimmerman

THE separation of fine sizes of coal from its impurities by means of various flotation methods has become of increasing importance in the coal industry. This, no doubt, will be even more so in the future as the quantity of high grade coal is depleted, particularly that used for metallurgical purposes. The purpose of this paper is to describe and report the results of research work done under the auspices of the Pittsburgh Coal Co. to determine the amenability of their bituminous fine sizes of coal to flotation, to investigate the value of various reagents and factors affecting their use, and compare the results between froth flotation and bulk oil flotation. Compared with the preferential flotation of complex minerals, or ores, the flotation of coal is comparatively easy. However, this statement should not lull one into the feeling that there are no special problems involved. For instance, the separation of coal from pyrite in high sulphur coals is still far from being 100 pct successful. Size consist has considerable effect on reagent consumption and recovery. Other factors will be described and finally it must be remembered that in the flotation of coal a low priced material is being treated and thus economic considerations govern more closely its application than is generally the case in treating other minerals. As a result of the research work done by the Pittsburgh Coal Co. on the flotation of coal, it was concluded that it was practical to clean the -48-mesh coal commercially by froth flotation and after several different types of flotation units and circuits were investigated by means of pilot plants, large scale units were installed at their Champion Nos. 1, 4 and 5 Preparation Plants for the cleaning of -48-mesh slurries. These large scale operations have been recently described by D. H. Davis. 1 C. P. Proctor and C. B. Carlson2 in their chapter on Froth Flotation of Coal in the AIME Seeley W. Mudd series book on Coal Preparation describe some of the practical applications of our Pittsburgh Coal Co. laboratory work in actual plant practice as well as summarizing part of the investigational work. The author presents this paper, however, as a supplement to their reports, and records the basic research accomplished in the laboratory investigational work as well as the results of experi¬ments using bulk oil flotation. In presenting this work the author wishes to state much more work must be done in applying the principles of flotation to cleaning coal, especially in view of recent studies and practices in other mineral beneficiation fields. METHODS OF CONDUCTING LABORATORY TESTS The bulk of the research work was conducted in the laboratory of the Champion No. r Preparation Plant. This plant has elaborate facilities for sampling and analyzing coal and proved to be an admirable location

Jan 1, 1948