Search Documents

By H. I. Aaronson, H. A. Domian

The self-diffusivity of Ag10 has been measured as a function of temperature and composition in AgMg. a CsCl-type intermetallic compound with a substitutional defect structure on both sides of the stoichiometric (50 at. pct Mg) composition. These measurements show that In D increases linearly, and both In Do and Q decrease linearly with deviation from stoichiometry. The slopes of these lines are significantly steeper in magnesium-rich alloys. Equations for the variation of Q with composition have been derived by application of the theory of random walk processes on the assumption that diffusion in compounds of this type takes place by the six-jump cycle mechanism of Huntington, Elcock, and McCombie. The favorable agreement obtained with experiment furnishes fresh support for the correctness of this assumption. A principal result of this treatment is that. although the concentration of vacancies is considerably higher in the silver sublattice than in the magnesium sublattice, the acfivation energies for movement of the magnesium sublattice vacancies are so much lower that these vacancies are responsible for effectively all diffusion of silver in this compound. A tendency for vacancies of both types to be kinetically bound to wrong atoms is also noted. THIS study was undertaken to examine the influence of substitutional defects upon self-diffusion in an intermetallic compound, AgMg, with a CsCl-type crystal structure. The CsCl structure is exception- ally simple. At the equiatomic or stoichiometric composition in a binary alloy, it consists of two interpenetrating simple cubic sublattices, each of which is exclusively populated by the atoms of one species. When atomic size and other factors are favorable, deviations from stoichiometry can be entirely accommodated by the substitution of atoms of the species present in excess of 50 at. pct on the sublattice of the other species on a one-for-one basis. Under this condition, the only vacancies present are those formed by thermal activation. The excess atoms thus incorporated into the sublattice of the minority species may be considered as substitutional defects in this sublattice. Several X-ray studies have shown that the defect structure of AgMg is entirely of the substitutional type on both sides of the stoichiometric composition.1"3 The thermodynamic investigation of Kachi indicates that, aside from a low level of thermal disorder and these constitutional defects, order is maintained to the solidus temperature. This compound is therefore a particularly useful vehicle for a study of the influence of substitutional defects upon diffusion kinetics. Other advantages of AgMg for this purpose include: the broad composition region, as much as approximately 10 at. pct on either side of the stoichiometric (50 at. pct Mg), in which the compound is stable; the comparatively low temperature range of the solidus (820°C and below),5 making diffusion anneals near this range experimentally convenient; the reasonably good machinability of the compound, permitting utilization of the standard sectioning method of radiotracer analysis; and the availability of a good tracer, A for one of the constituent species. While this investigation was in progress, Hagel and westbrooks reported data on the self-diffusion

Jan 1, 1964

By P. H. Mell

AMONG the minerals exhibited at the Atlanta Exhibition of 1881, soapstone, kaolin, and asbestos were well represented. The first two occur in large quantities, of very pure quality, throughout the South. The last is somewhat limited in amount, get in certain localities it exists in masses sufficiently large to pay for working; in North Carolina, Georgia, and Alabama it has ken mined with some profit. I would, in this paper, call special attention to the minerals soapstone and kaolin, because their many valuable qualities seem to have been almost entirely overlooked by our Southern manufacturers. Steatite, particularly, occurs in such large quantities, and generally in such close proximity to the great iron regions of Alabama and Georgia, that it is anlazing that the iron companies will persist in sending abroad under heavy expense for firebrick. It would require a much smaller sum of money to quarry this rock and place it at the various furnaces ; and the results obtained, I am sure, would prove its superiority over the majority of firebrick brought into this region. Soapstone, as well as kaolin, is found throughout the metamorphic regions of Alabama, Georgia, South Carolina, and North Carolina. Below will be found seven analyses that I have made of this mineral, taken from various points in the four States above mentioned. I have also subjected these same specimens to severe fire-tests, and the results were very satisfactory. The tests mere canducted in the following manner: Small portions of the compact variety were carefully weighed and placed in a Fletcher's new crucible furnace for gas, and subjected for half an hour to a heat that will in 12 minutes fuse iron. The only effect upon these specimens was a slight change in color to a darker shade, a small loss in weight, due evidently to the evaporation of water, and, in one or two specimens, a slight degree of fusion on the sharp edges. The first specimen subjected to investigation was taken from a large outcropping in Tallapoosa County, Alabama. Specific gravity, 2.88 ; hardness, 1.9; color, blue gray. Composition: Water,....2.68 Silica,..........65.48 Iron oxide,.........2.10 Alumina,.........15.02 Magnesia,... 15.35 10061

Jan 1, 1882

By K. O. Stamm, B. A. Rogers

Because it is the basis of the economically important operation of hardening steel by quenching, the A3 transformation in iron has been the subject of numerous investigations. Although the contributions to this subject are interesting, no general review will be given here. Readers who care to follow the matter further are referred to the comprehensive summary by Cleaves and Thompson,l which covers the literature to about 1935. Their references to 53 papers on the subject suggest that further investigation is hardly justifiable. However, considerable interest has devel oped recently concerning the reversibility of the transformation. From thermo-dynamic considerations, the transition ought to occur at the same point on heating or cooling, if the change of temperature is sufficiently slow. Yet all of the earlier investigators found a difference of several degrees. Burgess and Crowe,2 who used thermal methods, obtained average temperatures of 912" for Ac3 and 900°C. for Ar3 on electrolytic iron. Their data indicate a considerable range of temperature over which the change occurs, both on heating and on cooling. Terry3 measured the susceptibility in the critical range and estimated from the steepest parts of his curves that Ac3 came at 9I8° and Ar3 at 903°C. Ishiwara4 was one of the first investigators to report a shorter interval between the temperature of the change in the two directions. He measured the change of susceptibility of kaolin-coated samples of steel, in a hydrogen atmosphere, at rater of heating and cooling so low that about 3 or 4 hr. were required for the transformation to complete itself. His results show some variability between samples, but indicate that the difference between Ac3 and Ar3 is in the vicinity of 6°C. Roberts and Davey5 measured the space lattice in pure iron in the vicinity of 900°C. and concluded that a change occurs reversibly between 907' 3" and 910" 3°C., probably between 907" and 910°C. Wells, Ackley, and Meh16 made dilatometric determinations of the Ac3 and Ar3 points in samples of hydrogen-treated carbonyl iron maintained under a vacuum. They used three rates of heating and cooling: 2°, ½°, and .?°C. per min. and found the spread between the two points decreased with low rates. At the slowest rate, the Ac3 transition occurred at 909° to 909. 5°C. and the Ar3 change at 907°C. in three of the samples believed to contain the lowest percentages of alien elements. They concluded that if the rate of temperature change and the content of alien eiements were low enough, the A3 transformation would be completely reversible at 909.50 + 1°C. The question of reversibility is an interesting one and when some iron with especially small percentages of alien elements became available the opportunity to conduct an investigation was welcomed. This iron was prepared by the Division of

Jan 1, 1942

By B. A. Rogers, K. O. Stamm

Because it is the basis of the economically important operation of hardening steel by quenching, the A3 transformation in iron has been the subject of numerous investigations. Although the contributions to this subject are interesting, no general review will be given here. Readers who care to follow the matter further are referred to the comprehensive summary by Cleaves and Thompson,l which covers the literature to about 1935. Their references to 53 papers on the subject suggest that further investigation is hardly justifiable. However, considerable interest has devel oped recently concerning the reversibility of the transformation. From thermo-dynamic considerations, the transition ought to occur at the same point on heating or cooling, if the change of temperature is sufficiently slow. Yet all of the earlier investigators found a difference of several degrees. Burgess and Crowe,2 who used thermal methods, obtained average temperatures of 912" for Ac3 and 900°C. for Ar3 on electrolytic iron. Their data indicate a considerable range of temperature over which the change occurs, both on heating and on cooling. Terry3 measured the susceptibility in the critical range and estimated from the steepest parts of his curves that Ac3 came at 9I8° and Ar3 at 903°C. Ishiwara4 was one of the first investigators to report a shorter interval between the temperature of the change in the two directions. He measured the change of susceptibility of kaolin-coated samples of steel, in a hydrogen atmosphere, at rater of heating and cooling so low that about 3 or 4 hr. were required for the transformation to complete itself. His results show some variability between samples, but indicate that the difference between Ac3 and Ar3 is in the vicinity of 6°C. Roberts and Davey5 measured the space lattice in pure iron in the vicinity of 900°C. and concluded that a change occurs reversibly between 907' 3" and 910" 3°C., probably between 907" and 910°C. Wells, Ackley, and Meh16 made dilatometric determinations of the Ac3 and Ar3 points in samples of hydrogen-treated carbonyl iron maintained under a vacuum. They used three rates of heating and cooling: 2°, ½°, and .?°C. per min. and found the spread between the two points decreased with low rates. At the slowest rate, the Ac3 transition occurred at 909° to 909. 5°C. and the Ar3 change at 907°C. in three of the samples believed to contain the lowest percentages of alien elements. They concluded that if the rate of temperature change and the content of alien eiements were low enough, the A3 transformation would be completely reversible at 909.50 + 1°C. The question of reversibility is an interesting one and when some iron with especially small percentages of alien elements became available the opportunity to conduct an investigation was welcomed. This iron was prepared by the Division of

Jan 1, 1942

By D. A. Dukelow, G. Derge

THE Fe0-Mn0-Si0, system has many properties of fundamental interest besides its occurrence in steel-making. The system is the simplest ternary complication of the FeO-SiO, binary whose electrochemical properties have been explored. Therefore, knowledge of the conformance of Fe0-MnO-SiO, melts to Faraday&apos;s laws, as investigated by current efficiency measurements, would be of particular value in interpreting the observed variations of electrical conductivity, while at the same time furthering understanding of this type of molten oxides. Pertinent to the present study are conductivity data of FeO-SiO, and Fe0-Mn0-SiO2, and current efficiency data of FeO-SiO,. Concerning conductivity measurements, Inouye, Tomlinson, and chipman&apos; studied the specific conductivity, a, of molten wüstite as a function of temperature and oxide addition. Liquid FeO in equilibrium with an iron crucible was found to have a o whose magnitude and positive temperature coefficient were undeniably semiconductor in nature (o1400°C = 269 ohm-1cm-&apos;). Additions at 1400°C of 5 mole pct MnO decreased o to 227 while a similar addition of SiO2, dropped o to 125. Additional SiO2 produced an exponential decline of o. It was reasoned that because wüstite is known to be oxygen excess and since there is no pronounced change in oFeO upon melting, that UFeO(L)is p-type semiconduction. Björling2 gives o data for the ternary FeO-MnO-SiO, using fayalite, 2 FeO-SiO,, as the base substance. Upon addition of tephroite, 2 MnO-SiO, he noted a small decrease in o. Taking his data for 1400°C with one-half of the fayalite replaced by tephroite, o shows a decrease of some 40 pct relative to o for fayalite, i.e., 5 ohm-&apos; cm-&apos; to 3. In line with this observation, Mori and Matsushita3 reported that substituting MnO for FeO in the silicate de- creased o slightly except at high SiO, contents where the decrease was somewhat larger. Investigating the ionic nature of FeO-SiO2 melts, Simnad, Derge, and George4, found the anode current efficiency, C,, as calculated from iron anode weight loss, was temperature invariant and in general increased with SiO2 concentration. The authors suggested the possible presence of electronic conduction to explain why C+ < 100 pct. Fig. 4 includes their results as curve (b). EXPERIMENTAL METHOD Apparatus—Fig. 1 is a schematic section of the electrolysis cell used in all the current efficiency runs. The melt was contained in an iron crucible that rested on an alundum ring. A centered silica tube came within 1 in. of the surface of the melt and initially served as a thermocouple well and then as the guide for the anode.

Jan 1, 1961

By Roswell H. Johnson

The principle of sliding or graduation in royalties is accomplished either by the block, period, cumulative, or class method. The block method calls for a very low royalty rate on all oil produced up to a certain amount. This amount would normally be that which is believed to suffice to repay the cost of the well. A higher rate would be charged after the well is making a profit. This method, common in many industries, is peculiarly inadaptable to any industry such as this where the productivity per day of the units gradually and inevitably decreases. This, for reasons given later, is because it forces an early abandonment of the well and so offends against conservation. In the period method, the royalty rate is changed by some definite amount when the well produces less than a specified quantity per day or other given unit of time. While simple to explain, it operates badly because a great deal is made to depend upon a small reduction in production, whereas the reduction as a matter of fact declines rather erratically owing to the exigency of lease management, connecting of tankage, and vagaries of the gaugers. These disadvantages are obviated by the cumulative method. In this method, all the production less than a certain amount per week has one rate of royalty, or none at all, and the oil produced in excess of that amount pays an additional rate of royalty. In the long run the calculation is probably no greater than with the period method, for simple tables will be published and printed in the oil papers that can be cut out, enabling quick readings to be made. Even without the table the calculation is easy with the few royalty rates, two or three, which would be used. In this method, the amount paid in royalty declines gradually, rather than suddenly as in the period method. The following reasons might be advanced for the adoption oi cumulative royalties: 1. To distribute the burden in accordance with the capacity to pay. This principle is a unique one in business, although familiar in taxation. This is because it does not distribute reward in proportion to efficiency.

Jan 1, 1916

By R. J. Walter, W. T. Chandler

The Ch-H phase diagram was determined for by-drogen concentrations up to ChHo.9 at temperatures below 400°P&apos;. The phase diagram includes a mis-cibility gap and a eutectoid transformation. A peri-tectoid transformation is postulated at the hydrogen-rich end of the diagram, Phase diagrams were determined for two levels oj purity, of the columbium. A single solid solution exists in the Cb-H system above 400°F. There has been considcrable disagreement among investigators concerning the system at temperatures below 400°F. Albrecht, Goode, and ~allett&apos; proposed a miscibility gap containing two bcc phases with the two lattice parameters converging at about 140°C (285-F), and Brauer and ~erman&apos; found a two-phase room-temperature region between 10 and 41 at. pct H. At sufficiently high hydrogen concentrations in the one-phase region, the hydrogen-rich phase was found to be face-centered orthorhombic. Wainwright, Cook, and Hopkills3 recently reported that the face centered orthorhombic hydride phase is derived from a unit cell which is slightly tetragonal with a small departure from 90 deg of the angle (y) opposite the r axis. The orthorhombic hydride phase was observed for hydrogen concentrations between 0.2 and 0.8 H/Cb atom ratio. Paxton and coworkers4 found that needlelike hydride plates formed in a hydrogen-charged columbium single crystal and suggested that this transformation possessed the characteristics of a diffusionless phase transformation. On the basis of room-temperature, X-ray diffraction data, komjathy&apos; suggested that an order-disorder or martensitic transformation occurs. In the present study, the Cb-H system was investigated to resolve the discrepancies found in the literature for this system. PROCEDURE The columbium specimens were prepared from two heats of wrought 1/2-in.-diameter electron-beam melted columbium rod and from two columbium powders of -80 mesh size of different impurity contents. The columbium bar stock was pur chased from Urah Chmg Corp.; the 99 and 99.5 pct purity colulnbium powders were obtained from Fansteel Metallurgical Corp. and Kern Chemical Co.. respectively. The chemical analyses of the columbium bar and powders are listed in Table I. Hydrogen charging was performed by exposing the columbium specimens to hydrogen at 1 atm pressure at various temperatures. After exposure the specimens were quenched to prevent the hydrogen pickup which would take place if cooled in hydrogen, or the hydrogen loss that would occur if cooled in an inert gas. Adequate hydrogen purity was achieved by passing high-purity tank hydrogen (maximum 5 ppm total impurities) through an Engelhard catalytic Deoxo unit, magnesium per chlorate desiccant, and finally through activated charcoal at the temperature of boiling nitrogen. Activated charcoal at -321°F has been reported6 to remove impurities from hydrogen to a nondetectable level. A schematic representation of the heat-treating apparatus is shown in Fig. 1. A metal-sheathed thermocouple embedded in the colun~bium specimen was used to control the temperature during heat treatment and to pull the specimen boat into

Jan 1, 1965

An informal discussion on the application of physical chemistry to steelmaking was held during the Annual Meeting of the Institute in February, 1929. Alexander L. Feild presided. In opening the session, Mr. Feild said: We are all familiar with the cooperative mining and metallurgical studies that were begun in 1920 by the U. S. Bureau of Mines, the Carnegie Institute of Technology, and the Mining and Metallurgical Advisory Boards, and in particular with the work on the physical chemistry of steelmaking which was launched under the technical direction of Dr. C. H. Herty, Jr., in May, 1926. It was this work at Pittsburgh more than anything else that was the immediate cause of the formation within the Institute of a committee on the physical chemistry of steelmaking. During the latter part of 1927 a small group of Institute members interested in. the general subject of the physical chemistry of steelmaking undertook the organization of a subcommittee within the Iron and Steel Committee, to foster an active interest in this comparatively new field among the Institute membership and to obtain papers for publication in the Transactions, covering the various phases of the general subject. This plan was conceived by C. E. Meissner, to whose active efforts at the outset as well as during the past year is largely due whatever measure of success the plan has thus far attained. The subcommittee, now a committee of the Iron and Steel Division, was recognized and formally made a part of the Institute&apos;s organization at the February, 1928, meeting. As originally organized and as const,it,uted during the past year the committee has been made up as follows: C. H. Herty, Jr., C. D. King, A. B. Kinzel, John Johnston, C. E. Meissner, L. F. Reinartz, R. B. Sosman, and A. L. Feild, Chairman. Dr. C. H. Herty, Jr. has just been elected chairman for the coming year and C. E. Meissner has been reelected as secretary. From the outset it has been the settled policy of the committee to make membership an annual rather than a permanent matter and to reconstitute in part the membership of the committee each year by dropping a certain number of members and adding new members. In view of the fact that the work of the committee is still in a

Jan 1, 1929

By G. H. Anderson

Cadmium-coppeR precipitate, a byproduct of the purification stage of the zinc plant, is composed mainly of zinc, cadmium and copper in varying amounts depending on the efficiency of precipitation and the cadmium and copper contents of the impure solution treated. The composition range is approximately: cadmium 10-12 pct, copper 6-8 pct, and zinc 3&35 pct. As received at the cadmium plant, the precipitate is a dark gray to black press cake produced by filter pressing the flocculent cadmium-copper precipitate formed when impure zinc solution is agitated with zinc dust. The details of the cadmium-copper precipitation are to be found in the paper "Electrolytic Zinc at Risdon, Tasmania," by W. C. Snow. Transactions AIME, 121, 501. The treatment, in addition to recovering cadmium as metal, yields a copper product as a residue for realization and recovers in solution for return to the zinc plant, the excess of zinc dust used during purification. The recovery of cadmium metal is approximately 200 tons† per year, but, with the amount of copper residue recovered, varies with the zinc production tonnage, composition of the original concentrates, degree of roasting and other operational factors. The operations involved in the recovery of the foregoing materials are carried out in a building adjacent to the purification section of the zinc plant and can best be described by dividing the process into the following stages: 1. Oxidation and Grinding of the cadmium-copper precipitate. 2. Leaching and Filtering. 3. Precipitation of cadmium. 4. Oxidation and Grinding of the precipitated cadmium. 5. Leaching oxidized cadmium precipitate and Purification of leach solution. 6. Electrolysis. 7. Melting, Casting and Packing. A feature of the process is the use of two distinct solution circuits. Spent electrolyte from the zinc plant circuit containing about 10 pct sulphuric acid is used as the primary solvent of the cadmium and zinc present in the oxidized precipitate. When the cadmium is later separated by precipitation and filtering, the filtrate, originally zinc plant spent electrolyte and now fortified in zinc, is returned to the zinc plant. The precipitated cadmium, after oxidation, is redissolved in spent electrolyte from cadmium electrolysis which solution is in closed circuit within the cadmium plant except for discards to the zinc plant circuit as mentioned in Section 5 hereinafter. (Fig 1.) Details of the various operations follow. I. Oxidation and Grinding of the Cadminm-copper Precipitate The precipitate having had a preliminary drying by compressed air in Dehne filter presses in the zinc plant is trucked to a storage platform of sufiicient length to store 3 to 4 days&apos; production separately. After 48 hr exposure to atmosphere, oxidation is sufficient to enable all cadmium and zinc but only a portion of the copper to be dissolved in dilute sulphuric acid. The oxidized precipitate is shovelled into trucks and, after weighing and sampling, is broken in size by means of

Jan 1, 1950

By J. T. Norton, J. G. McMullin

An 1820°C isothermal cross section of the Ti-Ta-C ternary diagram was prepared from X-ray diffraction and metallographic data. No phases other than those appearing in the three binary diagrams were observed. At temperatures above the titanium transition temperature titanium and tantalum form a complete series of solid solutions containing up to 2 atomic pct C. The phases Tic and TaC also form a continuous series of solid solutions extending across the diagram. PREVIOUS work on this alloy system was very limited. Of the three binary constitution diagrams involved, only one, the Ta-C system was available in the literature. Preliminary data on the other two systems was received from the investigators during the course of the investigation and both have been published in recent months. It had been shown that Tic and TaC formed a continuous series of solid solutions, but the range of carbon content in this phase was not known. While Ta2C had been described, its solubility for or reactions with other carbides had not been reported. It was not known whether or not any ternary compounds occurred in the system. The present program was undertaken to determine experimentally the general form of the ternary diagram. It is hoped that the results will be of value in furthering the development of sintered carbide cutting materials and high temperature ceramets, many of which contain combinations of Tic and TaC. The Binary Systems Of the three binary diagrams involved only that of Ta-C was available at the time this project was started. The diagram of Ellinger¹ redrawn in Fig. 1, shows a hexagonal phase Ta2C having a very small composition range and a cubic TaC phase having a composition range of from 40 to 50 atomic pct C. The authors made a separate determination of the composition range of TaC using lattice constant values and found the range to extend from 40 to 49.7 atomic pct C in good agreement with Ellinger&apos;s diagram. Two determinations of the Ti-Ta system have appeared recently.2,3 These two diagrams are in good agreement and show that ß titanium and tantalum form a complete series of solid solutions. The Ti-C diagram by Cadoff and Nielsen4 shows a very limited solubility of carbon in both a and ß titanium. The single carbide formed persists over a wide range of carbon contents. Several values for the upper limit of carbon content of this phase have been reported."&apos; The highest value obtained in the M.I.T. Laboratory was 47.5 atomic pct C with a lattice constant of 4.328?.5 Fattinger7 describes a gas carburization method which he claims produces stoichiometric Tic although he does not present any data showing that he actually had 50 atomic pct combined carbon. Several complete analyses on

Jan 1, 1954

By G. R. Rubly, H. J. Steele

LOCATION AND HISTORY THE San Manuel property is in townships 8S and 9S, range 16E, Gila and Salt River Base and Meridan, State of Arizona. This area is in the Old Hat mining district, southern Pinal County, and is about 3;2 miles southwest of the town of Mammoth on the San Pedro River and one mile south of the Mammoth mine at Tiger, Arizona. The property consists of over 150 contiguous lode claims. The Old Hat district was prospected prior to the Civil War, but there was little or no production until 1881.1 The chief producers have been the Mammoth and Mohawk mines, now consolidated and operating as the St. Anthony Mining and Development Co., Ltd. Production to 1936 was $5,200,000, of which 83 pet was gold.2 Since 1940 the production has been chiefly lead and zinc, and some molybdenum and vanadium. There are a few small properties in the vicinity that have produced very minor tonnages of copper ore. In the San Manuel group there are claims which have been held continuously from 1906 to the present time, and at least two churn-drill holes were put down on or near the outcrop in 1917. No logs for these holes are available, but it is assumed that the grade of copper encountered was not sufficient to encourage further exploration. A small amount of ore has been shipped from open cuts on the San Manuel outcrop area, but there is no record of the tonnage or grade. It is estimated that not more than 5o tons were mined. These cuts, plus a few shallow shafts and some short adits indicate limited and unenthusiastic prospecting at San Manuel. In 1942, through the efforts of James M. Douglas, R. B. Giffin, Victor Erickson, and Henry W. Nichols, owners of the San Manuel group, the Reconstruction Finance Corporation and War Production Board authorized the United States Geological Survey to investigate the property, and by their recommendation, the United States Bureau of Mines was authorized to put down a limited number of churn-drill holes. The Bureau of Mines carried on drilling from November 1943 to February 1945. Seventeen holes were drilled, varying from 305 to 1990 ft in depth. The property was brought to the attention of Magma Copper Co. in June I944 and an option agreement was made with the owners. Subsequently, a group of claims lying north of the original group and held by the Apex Lead Vanadium Mining Corp., and a group to the east held by the Quarelli family, were optioned. A drilling program was laid out to conform to the Bureau of Mines pattern, and drilling started in December 1944. San Manuel Copper Corp. was incorporated September 1945, and has carried on the exploration program to the present time. GEOLOGY General The mineralized outcrop, chief copper mineral of which is chrysocolla, is a tri-

Jan 1, 1947

By H. E. McKinstry

MOVEMENT on a fracture of irregular shape can cause local widening of the fissure and thereby offer freer channelways for circulation of ore-depositing solutions. This influence, coupled with large areas of wall rock available for reacting with ore solutions in brecciated and shattered ground can account for locally active deposition of metals and the resulting ore shoots. Such irregularities in the fracture system may be caused by local variations in the strength of rocks and by pre-existing lines of weakness, especially if these stand at favorable angles to certain components of the fracturing stress. Therefore correct interpretation of the mechanics of fracturing should permit deductions as to structurally favorable places on unexplored portions of the vein system. INTRODUCTION IT has long been recognized that movement on a curved or irregular fault surface is capable of separating the walls in certain portions of the fault, but until very recent years the importance of this mechanism as a factor in localizing ore shoots has escaped proper recognition. A short time ago W. H. Newhouse&apos; presented a careful analytical study of displacements and their corresponding open spaces. For reasons that will be discussed later, it frequently happens that portions of the vein which are favorably oriented are not merely wider but also richer than the average. In many cases the widening with its accompanying richness coincides with very minor changes in the dip or strike of the vein, irregularities that commonly escape notice unless the vein is mapped in detail and a careful geometrical analysis made. While the relationship between the width of the vein and the changes in dip or strike has been recognized as a matter of observation, the irregularities have been accepted as more or less the result of accident. There has been very little effort except in isolated cases to find out the causes of these changes in dip or strike. Yet it is clear that if the causes can be recognized and expressed in terms of geologic structure the geologist will know where to look for repetitions of these favorable conditions either on extensions of the same vein or on adjoining veins. Any lack of understanding of the causes is due to the limitations of our ability to interpret our observations and not to the sheer capriciousness of

Jan 1, 1941

By G. S. Cole

The temperature has been measured ahead of stationary solid-liquid interfaces under conditions approximating luzidirectional heat flow and therefore unidirectional solidification. Natural convection flow patterns may be deduced from the temperature distributions , temperature fluctuations, and shape of the interface. Fluid flow increases with the height and the rate of heat transfev through the interface and this is further manifested by a deviation of the interface from aflat vertical plane. The influence of fluid flow on solute inhomogeneity during alloy crystal growth can be inferred from the observed temperature distributions. A buoyancy force exists in the liquid ahead of a vertical solid-liquid interface, caused by a difference in density between cold fluid near the interface and warmer fluid in the bulk liquid. When the viscous and inertia forces in the melt exceed this buoyancy force, a flow of fluid takes place, termed natural or free thermal convection. Natural convection in purely liquid systems has been extensively studied for many years. 1"u On the other hand, fluid flow during horizontal crystal growth has oniy recently been the subject of experimental investigation."-25 The requirements for horizontal crystal growth differ from other heat flow systems. The small aspect ratio (ratio of height of cold wall to length of fluid) has never been considered. The uniform furnace gradient which supplies heat radially (and not necessarily symmetrically) differs from previous boundary conditions of uniform heat flux at the cold and hot ends. And most important of all an isothermal s/l interface is present which can adjust its shape and position to conform to heat and fluid flow. All of these boundary conditions involve complexities which cannot be readily solved analytically. Preliminary observation has demonstrated the penera1 shape of the natural convective flow pattern in transparent media.20&apos;24&apos;25 The flow is circulatory, directed toward the interface at the surface of the liquid, down and away from the interface at the bottom, and then up at the hot end of the melt. During crystal growth such a flow may interact with the solute boundary layer at the s/l interface to affect solute incorporation.M&apos;1B|28&apos;i!T Evidence has also been presented recently to show that thermal convective flow will affect the structure of ca~tin~s.~~-~~ The rate of heat transfer (conduction plus convection) in a given fluid system is a function of the temperature difference between the hot end of the liquid and the s/l interface and the height of the interface. At the lowest values of these variables* all heat is *It has been shown&apos; that adverse temperature gradients as low as O.OOS°C oer cm are sufficient to cause convection. transferred by conduction. When the temperature difference or interface height are increased, laminar fluid flow commences and heat transport takes place by laminar convection as well as by conduction; turbulent heat transfer takes place at higher values of these variables. In the transition region between laminar and turbulent flow, boundary layer separation takes place; fluctuations in temperature are also noted and increase in amplitude and frequency as turbulence becomes dominant. In this paper, fluid flow patterns in the melt ahead of a stationary interface are deduced from observations of temperature distribution and fluctuations, heat flow rate, and interface shape. The fluid flow ahead of advancing interfaces and the effect of such flow on solute incorporation may be inferred from these measurements on stationary interfaces. Observations during enforced fluid motion will also be considered. EXPERIMENTAL PROCEDURE The metal was contained in a lava boat 10 cm in length, 1+ cm in width, and 2 cm in height, as shown in Fig. 1. A water-cooled, molybdenum block heat-sink is at one end of the boat; surrounding this assembly is a slotted stainless-steel tube noninductively wound with a nichrome heating element. Temperature was measured by 38-gage Chrome1 vs Alumel thermocouples sheathed in 0.05-cm-diam graphite-coated stainless-steel tubing, which were moved longitudinally and vertically through the melt by means of a two-dimensional motorized micrometer stage. In some experiments the thermocouple junction was exposed, but in the majority of experiments the junction was welded to the sheath tip; no significant difference

Jan 1, 1968

By Gareth Thomas

The analysis of Kikuchi pattersns of exct ovientalions from single cryslals and paired Kikuchi lines from single and overlapping crystals is shown to be useful and quanlitalve and is applied to Phase transfovnzcitions including ordering, spinodals, mavten-silic, and nuclealion and growth pyocesses. 112 pinciple, the analysis of exacl orientations enables the crystal system and the Bravais lattice of a crystal to he determined. The advantages of the davk-field imaging technigure for detecting vevy small precipitates are also described. ALTHOUGH Kikuchi electron-diffraction patterns were first observed nearly 40 years ago,&apos; little systematic application seems to have been made of them, until fairly recently during electron microscopy, when their usefulness in contrast experimen and for determining exact orientations8&apos;9 has been pointed out. With the availability of gonio-metric specimen tilting stages it has now become possible to make much wider use of diffraction patterns, particularly the Kikuchi pattern, which is the main subject of this paper. The treatment presented here is not exhaustive but it is hoped that it will stimulate more use of Kikuchi patterns during electron-microscopy investigations. The Kikuchi pattern is formed as a result of Bragg diffraction of the inelastically scattered electrons produced during the interaction of the beam and thick specimens, The important feature of these patterns is that they give an accurate representation of the symmetry of the crystal being investigated, so that it is possible to identify crystal systems and even the Bravais lattice. This means that new structures, e.g., formed in phase transformations, may be identified during normal electron microscopy, so that Kikuchi-pattern analyses considerably extend the uses of the electron microscope. Recent work has also shown that dark-field images are more informative than bright-field images, particularly, for observing small precipitates. The second part of this paper discusses some applications and advantages of dark-field imaging in studies of two-phase systems. 1) DIFFRACTION PATTERNS 1.1) Spot Patterns. Electron-diffraction spot patterns have their limitations because of the importance of the form factor on the intensities and shape of the reciprocal lattice points. Because of the extension of these points into relrods, reflections are possible over a large angular range (+5 deg) and the patterns from thin regions can be complicated because second-layer relrods intersect the reflecting sphere. Spot patterns can thus give only an approximate idea of the crystallography unless the foil is tilted into exact orientation. In this case the spot pattern is symmetrical, with equal numbers of spots on the positive and negative zone directions about the origin. Such cases are necessary for structural analyses and have been used recently to determine the crystal structure of the ordered Ta64C phase." Exact orientation means that the plane of the reciprocal lattice lies exactly normal to the incident beam as shown in Fig. 1(b). It should be noted that in exact orientations the angle of reflection is less than the exact Bragg angle 9 so that the reciprocal lattice points lie to the outside of the sphere, Fig. 1(b). This deviation is denoted by the parameter s and in the usual convention4 s is negative for exact orientations and, of course, zero at the exact reflecting position shown in Fig. l(a). In order to avoid secondary reflections from thickness relrods it is advantageous to work in thicker regions of foils. Diffraction from thick regions may also produce Kikuchi patterns and as dis-

Jan 1, 1965

By Arthur L. Walker

In June, 1893, while I was with the Old Dominion Copper Co. at Globe, Ariz., I received an offer to take charge, as manager, of the Baltimore Electric? Refining Co. which had recently built a plant at Baltimore, Md., having a capacity of about 1200 tons of electrolytic copper per month, using the Hayden series system. This was a very large output, for in those days the plants were small and the art was in its infancy. At the beginning of 1893 there were 11 electrolytic refineries in the United States, most of them using the multiple system. The Hayden series system was used at Baltimore and Bridgeport and the Smith series system was in operation at the Electrolytic Copper Co. at Ansonia, COM., and at the Pennsylvania Salt Co. at Philadelphia. In the latter system the plates were placed in a horizontal position, but the operating difficulties were so numerous it was soon discarded. The total production of these 11 plants in 1892 was very small; I have not been able to discover reliable figures of production. There were about thirty electrolytic copper refineries in the world that year, according to Titus Ulke, and the entire production of these

Jan 1, 1932

By F. S. Crawford

IRON and copper are mined in the Lake Superior district. The iron mines of the district have the best safety record for that industry in the country as a whole, while the copper mines of the district rank second in two of the four years recorded (Table 1). In Utah copper comes mainly from open-pit mines, which enables that state to lead easily in safety. All of the Michigan production comes from deep underground workings. About 60 per cent of the iron miners in St. Louis County, Minnesota, are employed at open-pit mines; this favorably affects the combined open-pit and underground accident-frequency rate, as this county provides most of the Minnesota-mined iron ore. In Michigan, however, there are few open-pit mines, the bulk of the production coming from underground mines, while all of the Wisconsin production, just across the state line from Michigan, is from underground mines. In spite of the fact that fewer mines in Michigan use the safer open-pit method, the iron-mining industry of that state maintained a consistently low record from 1931 to 1934; however, it was many points behind its nearest competitor, Minnesota, with its much greater production from open-pit mines.

Jan 1, 1939

By J. W. Koger, R. E. Hurnrnel

QUENCHED, bcc p brass, P1, transforms to a mar-tensitic phase, when it is cooled below room temperature.&apos; This transformation can be followed using resistance measurements since the resistivity of the martensitic phase is considerably larger than that of the parent phase, Fig. 1.&apos; phillips3 first reported that, when Cu-Zn alloys containing between 37.0 and 39.0 wt pct Zn were quenched from the 0 region to room temperature, variable amounts of a phase could be observed depending on the mode of quenching. If the quench occurs very rapidly, the a phase forms by a "massive transformation". The resultant phase has the same composition as the high-temperature P phase from which it was formed. If the quench is less severe, the alloy is retained largely in the p form; however, some a is formed by precipitation. In this case, a contains more copper than the high-temperature 0 phase from which it has formed. The a phase most probably does not undergo a transformation in the temperature range where p transforms to low-temperature martensite. This can be deduced from the Eesistivity-temperature relation which is linear in this temperature range, Fig. 2. The stable a phase which is present along with R. E. HUMMEL is Assistant Professor, Department of Metallurgical and Materials Engineering, University of Florida, Gainesville, Fla. J. W. KOGER, Junior Member AIME, formerly with University of Florida, is now with Oak Ridge National Laboratory, Oak Ridge, Tenn. Manuscript submitted December 13, 1967. IMD.

Jan 1, 1969

By T. Johnston, B. Cox

The results of oxidation and corrosion experiments on niobium in oxygen and steam at temperatures of 350° to 650°C, and in dilute sulphate solutions at 300°C are presented. The oxidation of niobium in oxygen can be explained in terms of a pre-transition period, which obeys an approximately parabolic rate law, and a post-transition period in which a more rapid linear rate is partially stifled by restriction of the gas flow due to the gvowth of the porous outer film. Due to changes in the porosity of the outer layers the restriction presented by the porous outel. film attains a limiting value. Subsequent oxidation obeys a linear rate law and shows an almost linear dependence of the rate on gas pressure. liltimately a second failure of the protective film may take place leading to a further acceleration in the oxidation rate. In water vapor the oxidation of niobium follows a parabolic rate law and does not show a transition to linear kinetics. The higher oxide, Nba05, was usually absent from the NbO/NbO2 film which was formed. The addition of a small partial pressure of oxygen to the water vapo3, resulted in accelerated oxidation according to the normal kinetics for oxidation in oxygen. The oxygen reacted preferentially with the niobium, and the protective oxide film was reformed when all the oxygen had been consumed. This behavior supports the theory that nucleation of Nb205 on the surface of the protective NbO/NbO2 film is the cause of the accelerated oxidation. After oxidation in steam at high-pressure Nb2Os was found in the protective film. The mode of formation of Nb2O5 under these conditions did not produce a change in kinetics, but was thought to explain the comparatively large dependence on pressure of the oxidation rate. The kinetics of oxidation in oxygenated aqueous solutions at 300°C were similar to those for oxidation in oxygen. A penetrating attack on niobium sheet may be related to the second breakaway observed by some investigators of oxidation in oxygen.

Jan 1, 1963

By O. Chanute

In discussion of Mr. Macdonald&apos;s paper, I can say little more thau to add t~ the general acknowledgments of iguorae, and like several of the gentlemen who have preceded me, make one of those confessions which are thought to be good for the soul. Having had some experience in the erection of bridges during past years, I am aware that We yet need much information in order to proportion them to the best advantage. I would more especially like to emphasize three of the points mentioned by Mr. Macdonald, as among those upon which we lack knowledge; these are: first, the behavior of steel; second, the proportions of compression members; and, third, the influence of the size of a bar upon its strength per square inch. First, as to steel. While we all acknowledge this as the material of the future, our position map be said to be still one of expectaucy. Feu? engineers are bold enough to employ it largely in bridges, and those who do, find such serious difficulties in obtaining uniform grades of it, are so puzzled by apparent anomalies and unexpected phenomena, that it requires considerable faith and courage to apply it in large structural masses. A series of systematic experiments,

Jan 1, 1882

By J. E. Ryan

TRONA, Calif., is a miniature urban community of some 3500 people, located on the northwest shore of dry Searles Lake in the extreme northwest corner of San Bernardino County, approximately 186 miles north and east of Los Angeles. Since it is situated on the Mojave Desert, a typically desert climate prevails with wide variations in temperature between day and night, extreme daytime summer heat, and cool to cold winters. Rainfall averages somewhat less than 4 in. per year, and dust storms are common. The rate of evaporation, .however, is great, amounting to 6 to 9 ft of water per year. The extremely low humidity makes the summer heat of 110°F tolerable with only a mild, temporary discomfort. Nature of Deposit During the periods when Searles Basin was flooded, the waters that passed through Indian Wells Valley spread out to form a broad, shallow lake providing, in effect, a settling basin for suspended sediment. The drainage into the deeper and more isolated Searles Basin thus was clarified to a great degree before concentration began. Today, the elevation of the dry surface of Searles Lake is 1618 ft, and the salt deposit measures 5x7 miles. At the eastern and northeastern margins of the main playa zone and just at the foot of the alluvial slope of sand and coarser wash from the Slate Range mountains, a rim of crusted salts rises a few feet above the level of the flat. The deposit is a saline efflorescence composed of salts that were presumably brought up with rising ground waters to be deposited at the surface by solar evaporation. This deposit consists chiefly of trona, and it is after this Trona Reef that the town Trona was named. Strip mining operations have been conducted in the past at infrequent intervals for the recovery of crude trona salts. The main focal point of interest in Searles Lake from a commercial standpoint is the main salt body located almost centrally in the basin. The exposed portion of this porous saline deposit covers approximately 12 sq miles and averages 71 ft deep. Its interstitial voids, which constitute 50 pct of the total volume, are permeated with a brine, which is in equilibrium with the soluble salt deposits. The brine is the raw material for the operations of the American Potash and Chemical Corp. plant at Trona, shown in Fig. 1. The soluble salt deposits are of interest for their potential values in future technologic development. The brine, which is stratified according to slight differences in density, stands usually within 6 in. of the surface of this exposed, firm, salt body. The surface is usually dry and will support the weight of heavy mobile units and drilling equipment. Occasionally, however, surface waters from the higher watersheds encroach upon the main salt body during infrequent periods of precipitation on the surrounding mountains. This water dissolves surface salt, becomes a dilute brine, and has been observed to stand as high as 18 in. above the salt surface when undisturbed. Windstorms will shift the water back and forth across the lake surface. The exposed salt body is surrounded by additional submerged areas of commercial soluble salt deposits covering some 20 sq miles, hidden from view by marginal playa mud. These vary in depth up to as much as 30 ft. Thus, the outline of exposed and submerged salt deposits of commercial value is estimated to cover a total area of 32 sq miles, which is roughly circular but slightly elongated from northwest to southeast. It has been estimated that each square mile contains about 100 million tons% f alkali salts. The results of drill borings in the past 15 years have brought to light the interesting fact that the main salt body lies superimposed on an impervious mud deposit from 10 to 15 ft thick containing relatively little soluble salt. Under this deposit lies a second soluble salt body 35 ft deep. The lower salt body is interspersed with numerous insoluble mud lenses and its composition is considerably different from that of the primary, or main salt deposit. Recent drill borings have not penetrated beyond 300 ft. They have, however, revealed that underlying the lower salt body, the mud sediments carry deposited minerals of trona, nahcolite, mirabilite and much less soluble carbonates or sulphates of calcium and/ or magnesium. This structure is shown in Fig. 2. Current Lake Survey Program Several hundred holes have been drilled in the deposit. However, to carry out a thorough and carefully correlated study of the composition of the soluble salts and other minerals in the dry lake basin, a drilling program was inaugurated recently and is now nearing completion. In this survey, pattern drill holes are sunk at regular lh-mile intervals to a depth of approximately 150 ft. Drilling equipment consists of a No. 51 C. P.

Jan 1, 1952