Search Documents

By J. L. Lummus, Frank O. Jones

A field procedure for determining graphite in drilling mud is presented which is sensitive to 0.25 lbs/bbl and accurate to 20 per cent. The method, utilizing oil flotation principles, is suitable for use in all oil-free water base muds except those containing ligno-sulfonates, lignites, or surface active agents. INTRODUCTION Graphite was proposed as a drilling lubricant as early as 1940, but has not been used extensively until recently.' Graphite has been substituted for oil in certain instances to avoid oil contamination of core samples since it has been found that graphite does not interfere with routine core analysis. A major difficulty in using graphite is the lack of a satisfactory field test for determining the concentration of graphite in mud. DISCUSSION OF METHOD Several possible methods of analysis were investigated, including chemical separation, density fractionation, radioactive tracers, and oil flotation.', ' The investigation indicated that a satisfactory method for field use could be devised using an oil flotation method. It was found that toluene shaken with a highly diluted mud sample would recover sufficient graphite to be apparent in the oil phase. Refinement and standardization of technique made it possible to detect as little as 0.25 lb/bbl graphite and to estimate graphite content to within 20 per cent by using a visual comparison method. The test is limited to oil-free water base muds. Quebracho, phosphates, or barytes in the mud do not interfere with the test but surface active agents, lignosulfonates' and lignites evidently render !he graphite water-wet so that none may be recovered by oil-flotation. PROCEDURE Instructions for determining graphite in mud: 1. Collect representative one gallon sample.- from mud stream. Transfer immediately 350 ml portions of this Sample into four mixing cans labeled A, B, C, and D. Measure out graphite (same as is used to treat mud) for addition to cans as indicated below, using either a specially designed scoop or a balance. Can: A B C D Grams Graphite to Add: none 2 4 6 Stir samples B, C, and D for 15 minutes with propeller type mixer. 2. Clean and rinse well with water four 250 ml volumetric flasks labeled I, 11, 111, and IV. Using a 5 ml hypodermic syringe, transfer the indicated volume of samples from cans A, B, C, and D into designated flasks as follows: From Can: A B C D To Flask: I II III IV Add This Volume of Mud: 4 ml 2 ml 2 ml 2 ml 3. Measure 100 ml fresh or distilled water to each flask and swirl gently to disperse mud. Add exactly 5 ml toluene to each flask. Stopper and shake each

Jan 1, 1953

By Edwin T. Myskowski, Alfred H. Hesse

THE development by the U. S. Bureau of Mines of a process for purifying manganese by electrolysis has stimulated interest in manganese alloys. While recent publications have shown some alloys of manganese and copper to possess rather unusual properties, none have included information on tensile properties, which have an important bearing on the usefulness of the alloys. Manganese-copper alloys can be heat-treated, since the single phases that exist at high temperatures may be retained by quenching. According to Persson,1 when quenched alloys containing from about 30 to nearly 100 per cent manganese are reheated, alpha manganese is precipitated (Fig. I). Calculations based on Persson's X-ray data indicate that this decomposition is accompanied by a change in volume of as much as 5 per cent. The reason that this large volume change has not been noted probably is the slow rate at which equilibrium is reached by these alloys. In an investigation on hardening by cold-work and heat-treatment, Dean and Anderson' found that quenched alloys increase in hardness with manganese content and that high-manganese alloys harden very slowly with cold-work, while high-copper alloys harden much more rapidly. Heat-treatment has little effect on manganese-copper alloys containing less than 40 per cent Mn, and affects those alloys containing more than 40 per cent in accordance with their manganese content and heat-treating temperature. Dean and Anderson4 also found that cold-work increased electrical resistance of alloys containing from 50 to 80 per cent Mn, and that heat-treatment of alloys containing from 40 to 96 per cent Mn altered the electrical resistance considerably. Dean, Anderson and Potter5 have shown that the high vibration damping capacity that characterizes manganese-copper alloys containing 40 to 90 per cent Mn is affected by cold-work and heat-treatments. Highest vibration damping capacity at low stresses was obtained by heating for 2 hr. at 450°C. (842°F.) after quenching from solution temperatures. Preparation of Alloys.-The alloys for these tests were melted in a 17-lb. basic-lined high-frequency induction furnace using electrolytic manganese, grade A ingot copper and a 70-30 Cu-Mn master alloy (69.80 per cent Cu, 0.12 Fe, 0.04 Si, 0.006 S, 0.07 C, balance Mn). The manganese was heated slowly to expel excess dissolved gases and melted before the addition of copper. No fluxes or covers were used. The melts were cast in tapered iron molds and the ingots were reduced 90 per cent when forged to ½ -in. rounds. These rods were given 2-hr. solution treatments at temperatures that depended upon the composition (Table I). Tensile Tests.-The tensile specimens, 0.313-in. diameter (1.25-in. gauge length), which were enclosed in evacuated Pyrex

Jan 1, 1942

By L. B. Slichter

After statement of the principles of similitude which apply to electromagnetic modeling, charts showing the inductive response of conducting spheres as dependent upon frequency, conductivity, and size are exhibited in this paper. The shape of the curve which relates intensity of response to frequency is significant in indicating the advisability of low frequencies in the exploration for conducting bodies, when consistent with the securing of a large percentage of the ideally possible response. Comparisons of theoretical response and that observed with models are shown, and relationships with the subject of applied electromagnetic prospecting are indicated. Maxwell Field Equations The Maxwell field equations summarize the physical laws that govern electrical field phenomena; they are the basis for the solution of electromagnetic problems. These concise equations, with adequately formulated boundary conditions, specify the complete electrical condition of continuous media, and the development of their solution amounts merely to a more convenient re-expression of phenomena already completely described. Thus, the immediate content of the field equations themselves is sufficient and sometimes convenient for the treating of certain questions (such as those relating to electromagnetic models) which are independent of the special factors of geometry, or the nature of an impressed field. The four Maxwell field equations are written below, in c.g.s. gaussian units: curl E = -B/c [21 div eE = 4pp [31 div B = 0 [41

Jan 1, 1932

By William F. Boericke

THE Christy Creek clay mine of the General Refractories Co., in the Olive Hill District, ranks with the most important producers in the north-eastern Kentucky fire clay field, both from production of high-grade flint clay, as well as unusual extent and thickness of deposit. The property is but one of a number controlled by the General Refractories Co. in this district, but is given first consideration among them by the operating staff. Its total area is over 5000 acres, owned in fee or by lease of clay mining rights, and although mining operations have been in progress for over five years, scarcely one per cent of the ground has been worked as yet. The mine is near the southwestern end of the clay field, which extends in a belt 12 miles wide and 55 miles long, in a southwestern direction from Kenova, W. Va., which, as the name indicates, is at the junction of Kentucky, Ohio, and West Virginia. Olive Hill, where there is one of the l1Ulin plants of the General Refractories Co., and to which the clay from the mine is shipped, is about 26 miles distant from the mine. Connection is made with the Chesapeake & Ohio R. R. by a spur line . 8 miles in length, owned and operated by the company.

Jan 1, 1929

By H. W. McCue, Henry Rogatz

Oil.—In the Texas Panhandle, 502 oil wells were drilled during the year 1940, with a total daily initial production of 139,187 bb1.—that is, 137 more oil wells drilled than in the previous year, with an increase in total daily initial production of 8219 bbl. The total daily potential of the field on Dec. 31, 1940, as determined by the Texas Railroad Commission, was 1,375,502 bbl., an increase of 30,825 bbl. over the previous year. On Dec. 31,1940, a daily allowable of 85,050 bbl., which was a decrease of 35 per cent over 1939, was assigned to the field to be produced from 4788 wells. The total amount of oil produced for the year was 26,788,590 bbl., making a cumulative total of 378,960,728 bbl. during the past 19 years. No new oil-producing acreage was discovered. Gas.—During the year, 92 gas wells were drilled, having a combined open flow of 2,402,900.000 CU. ft.; that is, 6 more than the number of wells drilled in 1939, with an increase in the open flow of 204,900,000 cu. ft. per day. The gas production for the year was 670,435,112,000 CU. ft., and the total gas removed from thc ground during

Jan 1, 1941

By Henry Rogatz, H. W. McCue

Oil.—In the Texas Panhandle, 502 oil wells were drilled during the year 1940, with a total daily initial production of 139,187 bb1.—that is, 137 more oil wells drilled than in the previous year, with an increase in total daily initial production of 8219 bbl. The total daily potential of the field on Dec. 31, 1940, as determined by the Texas Railroad Commission, was 1,375,502 bbl., an increase of 30,825 bbl. over the previous year. On Dec. 31,1940, a daily allowable of 85,050 bbl., which was a decrease of 35 per cent over 1939, was assigned to the field to be produced from 4788 wells. The total amount of oil produced for the year was 26,788,590 bbl., making a cumulative total of 378,960,728 bbl. during the past 19 years. No new oil-producing acreage was discovered. Gas.—During the year, 92 gas wells were drilled, having a combined open flow of 2,402,900.000 CU. ft.; that is, 6 more than the number of wells drilled in 1939, with an increase in the open flow of 204,900,000 cu. ft. per day. The gas production for the year was 670,435,112,000 CU. ft., and the total gas removed from thc ground during

Jan 1, 1941

By R. McDonald, B. C. Maine

CERRO'S power system consists of three main hydroelectric plants and one steam-electric plant. These are located on the eastern slope of the main Andes range at altitudes between 12,000 and 13,000 ft. The hydroelectric group utilizes the watershed which extends for about 150 kilometers south from Cerro de Pasco, divided into two catchment areas which lie adjacent. The northern area serve,, the medium-head plant of Mal¬paso. while the southern area provides for the high-head plants at Pachachaca and Oroya. The rainfall, as registered at the rain gauging stations of the three hydroelectric plants, averages 33 in. per year; all these stations are subject to the same hydrological conditions, and the bulk of precipitation occurs between October and March. Rainfall during the dry season, April till September, has no appreciable effect on the total annual runoff. Table 1 shows the storage capacities of the main reservoirs of the hydroelectric group. The four plants are tied together electrically by a 50-kv. transmission network, the system being 3-phase 3-wire at 60 cycles with a solidly grounded

Jan 1, 1945

By Orville R. Lyons, A. C. Richardson

DURING the past few years there has been a growing demand by coal operators for detailed information about the performance characteristics of the various dryers now being manufactured, preferably in such a form that the information could be used to determine the type of dryer best suited to a particular drying problem. A few operators have been desirous of going even further, because they are of the opinion that present-day dryers are not properly designed and that fundamental studies of dryer design should be undertaken. This growing demand for a method of dryer evaluation and the indicated need for fundamental research resulted in the sponsorship by Bituminous Coal Research, Inc. of a project at Battelle Memorial Institute to investigate the thermal drying of coal. In investigating this problem, the most feasible method of attack appeared to be a survey of active operations to determine the present status of the thermal drying of coal. Data were obtained, usually by actual plant tests with the cooperation of the various preparation engineers and their staffs, for Q screen-type dryers, 8 rotary- type dryers, 3 continuous-pallet-type dryers, 2 flash-type dryers, I tray-type dryer, and I cascade-type dryer. The testing program provided: (I) data for 24 coal- drying operations, (2) information about dried, (3) information about the previous treatment that the coal had received, and (4) information about operating costs. The data obtained through the dryer survey and relationships determined from the data make it evident that all of the types of dryers included in the survey can be operated with the same degree of effectiveness if each type of dryer is used to dry the sizes of coal for which it is best suited. It should be noted that it is usually undesirable and often impossible to dry different sizes of coal in one type of dryer. By use of the data in the report, any prospective dryer user, having determined the surface moisture percentage and screen- size analysis of the coal to be dried, the tons of water to be removed per hour, and the final surface moisture percentage desired, should be able to determine with a fair degree of accuracy: (I) the difficulty of the drying problem, (2) the approximate cost of drying, (3) the required dryer inlet gas temperature and volume and exhaust gas temperature and volume, (4) the type of dryer to use, and (5) the size of dryer required. The method of testing the dryers and determining the difficulty of drying can be used by operators already having dryers to check the performance of their particular dryer and determine whether they are operating effectively. Considerably more information was obtained from the survey of thermal drying than was anticipated when the survey was first considered. However, a great deal of work still remains to be done in the field

Jan 1, 1948

By R. W. Gurry

In the course of a series of measurements of the rate of diffusion of carbon in austenite at about 960°C. (1760°F.) and III0°C. (2030°F.), it became necessary to determine carbon concentration when austenite is saturated with graphite, because of indications that the hitherto accepted value of the solubility of graphite in this temperature range is too low. Specimens of carbonyl iron were saturated at temperature in a hydrogen-toluene atmosphere which was in equilibrium with graphite. The carbon conteDt of the steel was measured either by combustion or by the loss of weight after substantially complete decarburization in an atmosphere of hydrogen saturated at room temperature with water vapor. The absence of carbide or graphite as a phase at temperature was demonstrated by microscopic examination of saturated specimens that had been drastically quenched, The mean result of concordant ments-—taeats-is-^that gamma iron saturated with respect to graphite contains 1.39 per cent carbon at 957°C .(i755°F.) and 1.89 per cent at III0°C. (2030°F.). These two values, plotted along with what appears from the literature to be the best value (0.69 per cent) at the iron-graphite eutec-toid temperature (738°C. or I360°F.), yield a curve that is almost linear, and which, continued upward through a short interval, leads to a limiting solubility of 1.98 per cent at the iron-graphite eutectic temperature II35°C. (2075°F.) instead of the commonly accepted value of about 1.7 per cent. Experimental Procedure The samples of carbonyl iron, with the exception of those for microscopic examination, were cylinders 3.8 cm. long, 0.475 cm. in diameter. They were placed in a graphite holder and suspended in a vertical furnace, the temperature of which was controlled precisely by means of the resistance of the platinum winding.' In the empty furnace the range of temperature over a distance of 4 cm. at the heat center was 9°C. (I6°F.) but at a given location the temperature remained within +o.5°C. (o.9°F.); it was measured by inserting a platinum-rhodium couple calibrated at the melting point of palladium, 1555°C. Since the presence of the sample probably improved the uniformity of temperature, it was decided to consider the average temperature of the sample to be 3°C. lower than the maximum measured in the empty furnace with the same setting of the controller. Data were obtained in the vicinity of two temperatures, 960°C. (I760°F.) and III0°C. (2030°F.). The samples for microscopic examination, 2.2 cm. long, 0.475 cm. in diameter, were suspended individually on pure iron wire; for these no temperature correction was applied. The carburizing gas passed into the furnace was dry, oxygen-free hydrogen saturated at room temperature with toluene; this quickly produced on the

Jan 1, 1942

By R. W. Gurry

In the course of a series of measurements of the rate of diffusion of carbon in austenite at about 960°C. (1760°F.) and III0°C. (2030°F.), it became necessary to determine carbon concentration when austenite is saturated with graphite, because of indications that the hitherto accepted value of the solubility of graphite in this temperature range is too low. Specimens of carbonyl iron were saturated at temperature in a hydrogen-toluene atmosphere which was in equilibrium with graphite. The carbon conteDt of the steel was measured either by combustion or by the loss of weight after substantially complete decarburization in an atmosphere of hydrogen saturated at room temperature with water vapor. The absence of carbide or graphite as a phase at temperature was demonstrated by microscopic examination of saturated specimens that had been drastically quenched, The mean result of concordant ments-—taeats-is-^that gamma iron saturated with respect to graphite contains 1.39 per cent carbon at 957°C .(i755°F.) and 1.89 per cent at III0°C. (2030°F.). These two values, plotted along with what appears from the literature to be the best value (0.69 per cent) at the iron-graphite eutec-toid temperature (738°C. or I360°F.), yield a curve that is almost linear, and which, continued upward through a short interval, leads to a limiting solubility of 1.98 per cent at the iron-graphite eutectic temperature II35°C. (2075°F.) instead of the commonly accepted value of about 1.7 per cent. Experimental Procedure The samples of carbonyl iron, with the exception of those for microscopic examination, were cylinders 3.8 cm. long, 0.475 cm. in diameter. They were placed in a graphite holder and suspended in a vertical furnace, the temperature of which was controlled precisely by means of the resistance of the platinum winding.' In the empty furnace the range of temperature over a distance of 4 cm. at the heat center was 9°C. (I6°F.) but at a given location the temperature remained within +o.5°C. (o.9°F.); it was measured by inserting a platinum-rhodium couple calibrated at the melting point of palladium, 1555°C. Since the presence of the sample probably improved the uniformity of temperature, it was decided to consider the average temperature of the sample to be 3°C. lower than the maximum measured in the empty furnace with the same setting of the controller. Data were obtained in the vicinity of two temperatures, 960°C. (I760°F.) and III0°C. (2030°F.). The samples for microscopic examination, 2.2 cm. long, 0.475 cm. in diameter, were suspended individually on pure iron wire; for these no temperature correction was applied. The carburizing gas passed into the furnace was dry, oxygen-free hydrogen saturated at room temperature with toluene; this quickly produced on the

Jan 1, 1942

By HUBERT O. De

IN December, 1936, several drilling tests were made at the Hubert O. De Beck feldspar mine at Green Mountain, N. C., to determine the most efficient type of hammier-drill bit and drilling method for use at this particular property. This mine is well recognized as having the hardest rock in the Burnsville - Spruce Pine feldspar district and drilling costs always have been high. Local structural deformation has greatly distorted and warped the normal crystalline structure of the feldspar so the rock is much tougher than usual. In studying drilling methods and bit types, available literature was re¬viewed but little specific data could be found on the direct comparison of four-point and six-point drill bits so the following results may be of some interest.

Jan 1, 1937

By H. W. Ahrenholz

Seven weeks of 1971 were devoted to a nationwide coal walkout resulting in lost production of some 70 million tons and leaving 1971 coal production at about 550 million tons. Compounding the problem, consumption of coal in 1971 by electric utilities rose by about 5% to 336 million tons. In the mean- time, numerous contracts were awarded for coal R&D including $24.8 million given by the Office of Coal Research to Bituminous Coal Research for the construction of a coal-to-gas pilot plant using the BIGAS process. Exports declined mainly due to Japan's decrease in steel production and to that country's increase in coal imports from Canada and Australia. The advances in equipment design and mining procedures made 1971 a noteworthy year. Introduction of the variable pitch I dipper, the trend toward wheeled vehicles, the greater use of scrapers in reclamation and battery-operated vehicles and oscil-mining, and the increased activity in the areas of ventilation and dust control were given widespread approval. There were also strides made in computerization, longwall mining, roof bolting, rock dusting, mine haulage and methane detection.

Jan 2, 1972

Members Dues Resignations, Suspensions and Expulsions Institute Meetings Board of Director?s Meetings Directors and Officers Duties of Officers Committees Nomination and Election of Officers Publications Divisions, Local Sections, Affiliated Societies Amendments [As REVISED FEBRUARY 21, 19281 ARTICLE I MEMBERS-QUALIFICATIONS AND ELECTION , SEC. 1. The membership of the Institute shall comprise six classes, namely: 1. Members; 2. Honorary Members; 3. Senior Members; 4. Associates; 5. Junior Associates; 6. Rocky Mountain Members. All shall be equally entitled to the privileges of membership, excepting that Junior Associates, and all Members and Associates whose residence shall be outside of the United States of America, Mexico and Canada shall not be entitled to vote. SEC. 2. Members: A person to be eligible for election or transfer into the class of Member must be at least 27 years of age and must have had at least six years' employment in the practice of engineering, mining, geology, metallurgy, or chemistry, during at least three years of which he must have held positions of responsibility in one or more of these fields. This shall not apply to Rocky Mountain members.

Jan 1, 1928

By Sadtler, C. B.

IT is generally assumed that in most metals and alloys a given tensile stress produces a given deformation irrespective of the length of time during which the stress is applied. This assumption is justified in most of the important engineering applications of metallic materials; however, in the case of some metals and alloys used or tested at temperatures over or slightly under that at which recrystallization can occur the assumption is not warranted.1 This paper deals with the variations of deformation produced by a constant tensile stress acting for varied lengths of time in the special case of thin aluminum alloy sheet of the duralumin type, which had been subjected to different thermal and mechanical treatments. The material investigated was in the form of a sheet approximately 0.002 in. thick, which had been cold-rolled from a thickness of 0.020 in. It has been found that at a sufficiently high constant tension such material deforms continuously with the elapse of time and that the rate at which this deformation occurs is greatly influenced by the previous thermal and mechanical treatments.

Jan 1, 1927

By L. R., McLeod

NO important changes in metallurgical practice are exhibited in the smelter that has been erected for treating the Morenci concentrate: the material is charged to reverberatory furnaces without roasting, and the matte subsequently blown in Peirce-Smith converters to separate the iron and sulphur from the copper. In fact the process is essentially the same, except for preliminary roasting of the concentrate, that was adopted in the new smelter that was built for the Arizona Copper Co. at Clifton, a few miles away, to treat Morenci concentrate just before the start of the first World War, and which went into service in October, 1913.

Jan 1, 1942

By William Brewster

DATING back some five years ago, various foundries made inquiries as to the probable total carbon content in a given specification and grade of pig iron. Up to that time we had no data, and except for a few occasional determinations of total carbon, no attempt had ever been made to set up routine determinations of total carbon. In fact, at that time, a cast analysis was considered sufficient, without examining at further length into possible variations of analysis between ladles of the same cast. In view of the various inquiries as to total carbon, we sampled all piles of all grades of pig iron, making complete analyses. Finding some variation in carbon content, we secured more samples and plotted the carbon content with respect to silicon in each grade of iron except for the higher phosphorus foundry iron, where it was necessary to divide the group into twenty-point phosphorus ranges. This is easily understood, owing to the falling off of carbon content with the increase in phosphorus con-tent, silicon in each case being the same. In addition, these curves clearly demonstrate the lowering of the carbon content as the silicon is increased. In order to insure accuracy and reliable determinations the following method of sampling and analysis was employed: Two pigs selected from each end of the car, each car containing iron from one 50-ton ladle, are drilled with a 5/16-in. drill all the way through from top to bottom in the center of one section of the pig. The drillings are collected and transferred to an 80-mesh sieve; the portion passing through and the portion retained are placed in separate envelopes and labeled accordingly. The amount of sample in each envelope is weighed to obtain the proportionate amount of coarse and fine drillings, then a factor weight of sample (1.3636 grams) made up of proportionate

Jan 1, 1936

By A. E. Jenkins, L. A. Baker, N. A. Warner

Rates oj decarburization of levilated Fe-C droplets conlaining 5.5 to 0 pct C have been measured at 1660°C. Gas mixtures of 1, 10, and 100 pct 0, with helium diluenl were used at velocities of 12.5 and 62.5 cm per sec. Rates were independent of carbon concentration in the mell and in good agreement with the calculated rule of oxygen diffusion through the gas boundary layer. The effects of flow rale and total pressure are as predicled and the rates are approxitnalely 2.5 times those with CO2 as oxidant. The mass-transfer correlation used incorporaled the efject of natural convection as well as forced conrection. Graphile spheres are shown to oxidize at the same rate as Fe-C droplets under the same experimental codlions. It is concluded that, for high carbon concentrations in the melt, the rate of- decarburizalion is controlled wholly by the rate of gaseous diffusion. Rate measurements with pure CO, are reported for low carbon concentrations where CO bubbles nucleate within the droplet. Under these circumstances the decarburi-zation decreased with carbon concentration and it is proposed that carbon diffusion is significant in conlrolling the decnvburization rate. In an earlier paper1 decarburization rate measurements were reported for levitated Fe-C alloys at 1660°C but with CO2 as the oxidant. The decarburization rate was found to be independent of carbon concentration in the melt but slightly affected by total pressure. The authors were unable to explain the slight pressure effect but in all other respects the results were consistent with control by diffusion in the gas boundary layer. Subsequent work has been directed at finding the reason for the slight pressure effect and whether the kinetics with oxygen as oxidant parallel those with CO2. Recently Ito and Sano2 have shown that with water vapor-argon atmospheres the decarburization rate is gaseous diffusion controlled until an oxide film appears on the surface. In this work the melts were contained in crucibles. MASS TRANSFER IN THE GAS PHASE In the earlier analysis1 only forced-convection mass transfer was considered. Subsequent recognition of the existence of some free-convection mass transfer explained the observed small effect of total pressure on the decarburization rate. Steinberger and Treybal3 and Kinard, Manning, and Manning4 have developed correlations involving the linear addition of the contribution of radial diffusion, free and forced convection. Steinberger and Treybal&apos;s correlation was chosen as the most applicable to the present work since it correlated most of the data available in the literature and handled the low Reynolds number region exceptionally well. The correlation for (Gr&apos;Sc) < 108 is where Nu&apos; is the Nusselt number for mass transfer based upon the total surface of a sphere in an infinite medium, G&apos; is the mean Grashof number for mass transfer defined by Eq. [2], Sc is the Schmidt number (µ/pDAB)f, Re is the sphere Reynolds number (dpu,pf/µf), p is the viscosity of the gas (poise), p is the density of the gas (g cm-3), Dab is the binary diffusivity for the system A-B (sq cm sec-&apos;), dp is the sphere diameter (cm), u is the approach velocity of the gas (cm sec-I), and subscript f denotes the property value is computed at the film temperature Tf defined by Tf = +1/2(To + Tr) where To is the specimen temperature and T, is the approach gas temperature (oK). Natural convection occurs when inhomogeneities exist in gas density. These may be caused by concentration gradients, temperature gradients, or both. In the present work the temperature gradient between the sphere and the bulk gas was very large and in some cases, for example the runs with pure oxygen, the concentration gradient was also appreciable. The Grashof number defined by Mathers, Madden, and piret5 was used since it took account of both temperature and concentration gradients: where Gr&apos; is the Grashof number for mass transfer (p2fgd3|-yA-yA|/µ2f), Gr is the Grashof number for heat transfer (p2f gd3p|To - T,]/µ2fTf), Pr is the Prandtl number (cpµ/k)f, g is the acceleration due to gravity (cm sec-&apos;f, a is the concentration densification coefficient (1/p)(ap/ayA)T, yA is the mole fraction of component A at the gas-metal interface, yA is the mole fraction of component A in the bulk gas stream, cp is the heat capacity of the gas per unit mass at constant pressure (cal g-I OK-&apos;), and k is the thermal conductivity of the gas (cal cm-&apos; sec-1 OK-1). Mathers et al. tested this combined Grashof number

Jan 1, 1968

By A. H. Grobe, F. N. Rhines

THE constitution of the indium-zinc alloy series has been investigated by Wilson and Peretti,1 who determined the liquidus and eutectic temperatures by the conventional method of cooling curves and the eutectic composition by analyzing eutectic exudations. Recent developments affecting the availability of indium and consequent increased interest in its applications make a more complete knowledge of the constitution of its alloys desirable. As a part of a program for the reexamination of the constitution of indium alloys by precision methods, the indium-zinc phase diagram [ ] (Figs. I and 2) has been redetermined in its entirety. The eutectic temperature (143.5°C.) reported by Wilson and Peretti has been confirmed exactly, but their value of the zinc concentration at the eutectic, 4 per cent, was found to be high; the new value is 2.8 per cent of zinc. There is also a rather large difference between the forms of the liquidus curves of Wilson and Peretti and those found in the present studies. The solidus curves herein have been located for the first time and the limits of solid solubility have been tenta-

Jan 1, 1944

By E. J. ENGEL

The New York talc deposits of commercial importance are in St. Lawrence and Lewis counties, in the northwest Adirondack Mountains (Fig 1). All of the deposits are of pre-Cambrian age and occur within highly deformed and recrystallized marble of the Grenville series. The deposits in St. Lawrence County, near Gouverneur, are the largest and most productive of their type known in the Western Hemisphere. In 1948 the seven mines which are in operation will produce about 130,000 tons of ground talc. All talc production in Lewis County is from one mine. There the annual production ranges from 15,000 to 30,000 tons. These so called talcs of New York State include earth materials of differ- ent chemical and mineral compositions. In general the mineral talc is sub- ordinate in amount to other minerals in both the Gouverneur and Natural Bridge deposits.

Jan 1, 1949

By John E. Sherborne, William M. Newton

THE relation between the properties of electric logs and the fluid used in drilling a well is briefly discussed in this paper, and the fact that the resistivity of the drilling mud and its filtrate can appreciably affect such logs is shown. Apparatus was designed and a procedure established to determine the effect of various factors on the resistivity of drilling mud. Five muds commonly employed in California were tested and the following observations were made: I. The effect of raising the temperature from 80°F. to 180°F. is to decrease the resistivity of the mud or filtrate approximately 50 per cent. 2. The resistivity of the mud in most cases closely approximates that of its filtrate. 3. The change in the resistivities of muds caused by the addition of chemical is not the same function of the amount of chemical added for each mud. 4. The effect produced by increased sodium chloride content is to reduce markedly the resistivity of the mud and its filtrate. 5. Weighting materials, such as Baroid and limestone, tend to increase the resistivity of drilling mud. 6. Cement and counteracting reagents reduce mud resistivity.

Jan 1, 1942