Search Documents

By R. H. Martinson, E. Teghtsoonian

The effects of magnesium-rich surface layers of varying thickness on the mechanical properties of LiF have been studied. The yield stress, critical tensile stress, and work-hardening slope increase linearly with layer thickness, while the strain to fracture decreases yapidly with increasing layev thickness. The results of tension tests, supplemente!d by metallogvaphic evidence, indicate that the yield stress and the critical tensile stress of LiF are not determined by surface-source operation. DESPITE many studies, which have recently been reviewed,' certain fundamental aspects of the plasticity of LiF remain obscure. For instance, one question still awaiting a satisfactory resolution is: does the nucleation and/or multiplication of dislocations in LiF occur preferentially near the crystal surface? It is now well-known that mobile dislocation half-loops are readily introduced into LiF by surface damage and that the mechanical properties of LiF are affected by such surface damage. However, it is not known whether, in the absence of large numbers of artificially introduced surface sources, dislocations arise more easily near the crystal surface than in the crystal interior. It is also not known to what extent existing mobile dislocations multiply preferentially near the crystal surface. The present work is an experimental study of these matters. A short investigation of the effect of magnesium -alloyed surface layers on the deformation of LiF single crystals has been published by Westwood.~ Some relevant conclusions drawn from this research are restated here for purposes of comparison with the present work. 1) Tests on as-cleaved, chemically polished, coated and uncoated specimens show that a coating can restrict the operation of artificially introduced surface sources, thereby raising the yield stress. A coating also decreases the initial rate of work hardening of as-cleaved LiF crystals by reducing the number of active dislocation sources, so that mutual dislocation interference effects are lessened. 2) A catastrophic breakthrough of groups of edge dislocations piled up against the coating can cause stress drops in the stress-strain curve. 3) A surface coating can act as a stable barrier to the egress of dislocations, causing pile-up,

Jan 1, 1965

By FRANK COLE

THE territory covered in this discussion includes all the states west of the Mississippi river. Agriculture is expanding each year in this section, but until recent years the application of commercial fertilizers as an aid to crop production was not practised to any great extent. The use of commercial fertilizers has increased somewhat, but is still on a small basis as compared with the tonnages used else- where in the United States. During 1928 these western states used 665,100 tons of all classes of fertilizer as compared 'with 7,933,600 tons used in the whole United States; or this western area, compromising near- ly two-thirds the land area, uses about 5 per cent of the total fertilizer. To show how large a tonnage one state may consume, North Carolina for the year 192s used 1,349,360 tons of commercial fertilizer or about twice the amount used by 22 western states.

Jan 1, 1930

By A. Keil

TO measure the absolute conductivity of metallic specimens it is generally necessary to have exact geometrical shapes and good electrical contact with the test-piece. To overcome limitations of the standard methods, an electronic conductivity-meter* Trade name, Sigmatest; model Dr. F. Forster; Reutlingen, Ger-many. has been developed, which works on the principle of inducing high frequency eddy-currents in the specimens and measuring the reaction of these curients on a measuring coil.',' To attach the instrument to the test specimen, a flat area of about 10 mm diam is all that is necessary. The reading is taken off a scale calibrated in pet of International Annealed Copper Standard. The induced eddy-currents are propagated in a circular motion parallel to the surface. Thickness of the layer included in a measurement depends on the frequency used. With a frequency of 60 kc per sec, the penetration of the currents was 0.8 mm at the upper limit of the scale, and 2 mm at the lower limit. The method is limited to nonferrous metals and other applications have been described elsewhere." The object of the present investigation was to detect the formation and growth of surface layers of differing conductivity, and to determine the depth to which these changes could be observed. A well known phenomenon which illustrates the problem is the internal oxidation of certain silver alloys containing base metal solutes, such as copper or cadmium, when they are annealed in an oxidizing atmosphere.4, 5 Until now, the only methods available for following these phenomenon have been metallo-graphic examination and hardness tests.0, 7 Changes in mechanical properties of copper alloys by internal oxidation were recently discussed in a more general way by Martin and Smith." When measuring these conductivity changes it must be remembered that the only absolute values of conductivity are those of 1) the nontreated homogeneous specimen, and 2) the final values obtained with a surface layer of depth comparable to the penetration of the eddy-currents. All intermediate values refer to the mixed conductivities of the transformed surface layer and the untransformed alloy, and are thus readings of relative value only. Experimental Results Specimens were annealed for 1/2 hr at 800°C in hydrogen, and the internal oxidation was carried out by thermal treatment in air at 800°C. Fig. 1 shows the results of the first series of experiments. With internal oxidation of a solid solution of 8 pet Cd in silver, the conductivity rises continuously until the surface layer formed has become thick enough to be the deciding factor (about 400µ). Precipitates of CdO are mainly in the form of points, Fig. 2, and, as a result, the electric contact between the silver crystals is not distorted by them. Brine11 tests were run with a 1.25 mm ball and a 7.812 kg load. The specimen annealed in hydrogen and oxidized to a depth of 400µ had a hardness of 40 Bhn,

Jan 1, 1959

By Norman Goss

IT is generally agreed that cold-working mechanically refines the grains into smaller fragments and with continued working these are oriented with certain crystallographic directions bearing a relation to the direction in which the metal is worked. Some of the energy expended on the metal during plastic deformation appears in the form of heat, but a very small portion remains in the metal as stored energy. The entropy, specific heat capacity, temperature at which recrystallization will just begin, density, ductility, elasticity, tensile strength, and resistance to corrosion are affected. These properties have been studied extensively and some of the changes in the physical properties due to cold-working were attributed to lattice distortion.1-8 The broadening of the K. lines on the X-ray diffraction diagrams of plastically deformed metals is believed to indicate lattice distortion, and consequently the existence of internal stresses. The evidence supporting this theory rests solely upon the observed experimental fact that the dif-fraction lines are broadened and the K a doublets are completely diffused. Elam9 has reviewed the matter of lattice distortion in relationship to the hardening of metals by plastic deformation. The X-ray diagrams of plastically deformed metals differ in general from annealed metals. The hardening of a metal was believed due to lattice distortion.9 The resolu-tion of the doublet is lost when a metal is cold-worked and the Lane spots are elongated. At one time this elongation was thought to indicate the elastic bending of the crystal planes. However, more careful work showed that the asterism was due to new orientations developed within the fragmented grains during plastic deformation. Some theories attrib-uted the hardening to fragmentation of the grains into smaller units.

Jan 1, 1940

By D. W. G. White

The surface tension of zinc has been determined by the sessile-drop method in a progvam emphaszzing detailed experimental care. The surface tension oj. the pure metal was measured over a range of ternperature from the melting point (419.6"C) to 540°C. At the melting point, the suvface tension of zinc was found to be: 1) 99.99+ pct Zn - 757.0 5 dynes per cm 2) 99.999+ pct Zn - 761.0 5 dynes per CI 3) 99.9999 pct Zn - 76'7.5 5 dynes pev cna From experiments carried out in a closed, isothermal cell, the temperatuve coejyicient of the surface tension (6y/6T)p, , of zinc xas found not to be negative but to be postiue. A positive tenzperatre coefficient indicates a greater depee of order in the surface than in the body of the lquid. Houlezer, by delibevately inducing continuous zaporization, a temperature coefficient of su)face tension with a negative slope can be produced. The work reported herein was undertaken as part of a larger program of fundamental research on the properties of molten zinc and zinc alloys. This program grew out of a continuing interest at the Mines Branch in the behavior of liquid metals in the foundry and of a desire on the part of the zinc industry for reliable basic data. The work was originally begun in cooperation with the Consolidated Mining and Smelting Co. Ltd., Trail, B.C., and was subsequently continued from 1960 to date in association with the Canadian Zinc and Lead Research Committee and the International Lead and Zinc Research Organization. Although the surface tension of liquid zinc has of course, been measured before, as Table I and Fig. 1 demonstrate, there is not good agreement among the existing values. Such disparities arise because sources of experimental error are insufficiently controlled. This situation places the reader in doubt. One result may be correct within narrow limits—even fortuitously—yet, because there is not agreement between several values, none can be accepted with conviction and all become suspect. It seemed, therefore, in the circumstances, that there was room for further work embodying considerable emphasis on experimental care in order that, within a small margin of error, an accurate value might be obtained. It was in this spirit that the work was undertaken. METHOD The sessile-drop method -as adopted for this work. In this method, when applied to liquid metals at elevated temperatures, the outline of the meridional section through a drop resting freely on a horizontal surface is recorded photographically. Certain parameters

Jan 1, 1967

By Basil Prescott

A thorough knowledge of the peculiarities of this type of orebody is necessary in sampling these limestone replacement deposits. Oxidized ores are often overestimated because of error in determining specific gravity and actual cross-section of the orebody, and sulfide ores are often underestimated because it is difficult to scatter the samples so that they will accurately represent the area under consideration. This paper describes various methods of sampling and cites factors that enter into the estimation of these deposits. IN THE science of evolution of the species, there is a law which, simply stated, avers that the history of the individual repeats the history of the race. Similarly, if unassisted by the experience of others, each successful engineer would perfect and develop his methods and technique from the rough grab sample up to the carefully taken, recorded and studied samples and observations which now determine and decide the expenditure of the large sums required for modern mining. Hence real progress results from the interchange of experience, as in that way the entire experience of the profession can be made available to every engineer. The literature of this subject is already voluminous, but some progress has been made in the gathering of data and in their compilation or presentation.

Jan 3, 1924

By Jose J. Alvarez

INTRODUCTION Three major plant processes control the operation of an uranium in-situ mining plant. The three pro- cesses can be categorized under the headings termed - loading, elution, and precipitation. All other plant processes can be subcategorized under the three. In summary, the major plant processes in an in- situ mining plant are: 1. Loading - The pregnant lixiviant from the production wells flows through anion exchange resin. The loading of the uranium on the resin is controlled by various factors, such as ionic strength, valence, functional groups, etc. 2. Elution - The uranium-loaded resin is eluted or regenerated by a high ionic strength solution. The effluent from this process is de- fined as the pregnant eluate. 3 . Precipitation - The pregnant eluate is chemically treated to attain the ideal conditions for the selective precipitation of uranium. Hydrogen peroxide is an ideal precipitating agent under URI conditions. This paper will focus on two of the major processes: Elution and Precipitation. For the most part this relatively young industry has grasped the theory of liquids in continuous flow for the operation of the plant processes. Likewise, URI initially operated the two processes of interest with the continuous flow concept. Through laboratory experiments, URI has abandoned the flow concept and operates the eluting and precipitating stages with the concept of "batch" processes, whereby only one container, filled to a specified liquid level, is chemically processed. In the proceeding sections, each of the two pro- cesses will be discussed in detail, from their original concept to the present operation. Only minor modifications were made to the existing circuits for the conversion with results revealing a greater level of efficiency. ELUTION The elution of the loaded anion exchange resin can be achieved by different high ionic strength solutions. The selection of constituents is dependent on both chemical and economic considerations (i .e., efficiency and operating/restoration factors). The regenerant presently used is a pH 9.5 solution containing 7.5% NaCl and a mixture of Na2C03/NaHC03. expressed as 2.5% NaHC03.

Jan 1, 1980

By R. W. Diamond

THREE mills are now operated by the Consolidated Mining & Smelting Co. of Canada, Ltd:: (1) The Sullivan concentrator, Chapman, B. C. (near Kimberley, B. C.), (2) the St. Eugene concentrator, Moyie, B. C., and (3) the Tadanac (customs) concen-trator, Trail, B. C. Differential flotation is the only concentration method employed in all three plants. Tables are used for pilot work only. Flotation equip-ment and control are similar in the three mills, and the flow sheets at the St. Eugene and Tadanac mills, while much simpler, are modeled after that of the Sul-livan concentrator. Successful differential flotation of Sullivan ore com-menced in the spring of 1920, in the pilot concentrator at Trail. During 1920, 193,804 tons were treated by this process. This operation continued without interrup-tion and with steady growth. For the first 7 months of . 1923, which concluded the pilot plant operation, ap-proximately 1100 tons were treated daily. I believe the Sunnyside plant of the United States Smelting &. Refining Co. was the only successful and large scale operation practising differential flotation prior to 1920. in North America. The Sullivan ore, because of its high iron content, was quite a different problem from that at Sunnyside. The entire tonnage of Sullivan ore had to be separated into three sulfide concentrate products-lead concentrate, zinc concentrate and iron concentrate. The choice and arrangement of equipment, and the original flow sheet for the Sullivan concentrator were controlled by the results of the exhaustive pilot mill test. These covered a continuous period of 3 1/2 years and involved the treatment of 1,076,368 tons of Sullivan ore. Satisfactory recoveries are made from feed; 11.0 per cent lead and 7.5 per cent zinc in the form of lead concentrate containing 69 per cent lead, 4.5 per cent zinc, and zinc concentrate containing 3.0 per cent lead and 49 per cent zinc. (The pure zinc mineral in Sulli-van ore is marmatite, 'containing approximately 54.5 per cent zinc and 10 per cent iron. It is apparent, there-fore, that 49 percent concentrate is high grade for this particular ore.)

Jan 8, 1927

By R. P. Rothwell

THE milling of silver ores has arrived at a great degree of perfection in the mining districts of our Western States and Territories, and I have thought the record of the practical results obtained at the present time, in a few of the principal districts, would prove of value and interest to many of our members, both at home and abroad. An American silver mill is composed, in descending order from where the ore is dumped, of: 1st. A rock-breaker, usually of the Blake or Alden pattern ; 2d. The battery of stamps, the number of which varies from 5 to 120, generally in batteries of 5 or 10 heads, so arranged that a single battery may stand while the others are running; 3d. The tanks where the crushed ore settles (if it is a wet stamping-mill), or of a drying-floor if the crushing is done dry; 4th. Amalgamating pans ; 5th. Settling pans ; 6th. Agitators or pans in which mercury escaping in the tailings is caught; 7th. Blanket sluices, over which the tailings run, and where mercury and unamalgamated sulphides are saved. A reference to the engravings (see plate), which show one of the latest forms of an 80-stamp silver-mill run by a turbine water-wheel, will show clearly the arrangement of the several parts. THE ONTARIO, UTAH, SILVER MILL. One of the best examples of a silver-mill, and at the same time one of the most successful concerns in the West, is the mill of the Ontario Silver Mining Company, near Salt Lake, in Utah. This mill treats the ore from the Ontario mine, ore which at present is very base, being composed of zinc, lead, and silver sulphides and silver chloride in a quartz gangue. This ore has become baser as the mine attained greater depth, though the vein holds its own, or rather increases, both in thickness and richness. The mill is man¬aged in a skilful and economical manner, though the necessity for * Read at the Montreal meeting, September, 1879.

Jan 1, 1880

By Leonard Greenburg

The American literature in the field of dust sampling and analysis has been growing rapidly since 1915. Studies made since that time clearly indicate that there are three fundamental factors that determine the production of lung pathology due to dust inhalation. These are the duration of exposure, the chemical and mineralogic nature of the dust and the concentration of the potentially harmful dust. In the estimation of the amount of the potentially hazardous dust there are essentially three problems involved: (I) a determination of the size of the hazardous dust; (2) determination of the most satisfactory apparatus and technique of sampling, and (3) the most satisfactory method of analysis. A complete study of the literature shows that industrial dust varies ill size from ultramicroscopic particles to those larger than lop in diameter and that relatively few particles are found over 5u in diameter. Approximately 10 to 25 per cent are less than 0.811 in diameter and the median size as a rule is found to lie between 1.25 and 1.75 microns. From the point of view of lung pathology the particle sizes of most importance lie between 0.5 and 5u. Of all the instruments for sampling dust the Impinger apparatus is the only one that will sample a larger body of air satisfactorily with small control errors and high efficiency in both low and high concentrations of dust. The Owens apparatus has the advantage of being more portable and somewhat easier to use but it does riot permit of the sampling of large volumes of air. It has a low efficiency in high concentrations of dust and does not permit dust weights to be obtained. From the point of dust-counting technique the author points out that in 1922 considerable experimentation with dark field and oblique illumination resulted in the conclusion that such methods were not readily duplicated from day to day and therefore yielded somewhat erratic results. Changes in the amount of illumination produced variations of several hundred per cent in dust counts obtained with dark ground

Jan 1, 1934

By J. E. Korski

Quebec Cartier Mining Co. operates a low-grade iron ore deposit at Lac Jeannine, Que., which is located at the extreme southwestern end of the Quebec-Labrador Trough (Fig. 1). The facilities there include one of the world's largest concentrators, a hydroelectric plant of 60,000 hp, and the modern town of Gagnon. A 191-mile railway connects the mine to the seaport situated at Port Cartier on the St. Lawrence River. The harbor in Port Cartier can accommodate both lake and large ocean- going vessels and is also the site of a major grain terminal. The concentrator in Lac Jeannine is designed to produce some 8 million tpy (tons per year) of specular hematite concentrate, containing 66% Fe, from approximately 20 million tons of crude ore. An annual stripping program of 5 to 8 million cu yd of waste rock uncovers the required ore. Approximately 100,000 tons of ore and waste are removed daily on a year-round, 24-hr-per-day basis. The open pit covers an area with maximum dimensions of 8,000 x 2,600 ft (Fig. 2). Present mining plans call for an ultimate depth of approximately 1,000 ft below original ground level. The rocks in the pit area are typical of this portion of the Grenville geological province. They consist largely of marble, quartz rock, pegmatite, iron formation, and stratigraphically older gneisses. The iron-ore formation consists of medium to coarse-grained specular hematite in a quartz host rock. The formation occurs locally in a plunging, anticlinal form. The topography in the vicinity of the mine is rolling, with maximum variations in elevation of about 400 ft. The hills are thickly wooded with birch, black spruce, and some tamarack. Lakes and muskeg areas are plentiful. Precipitation and temperature records have been kept since 1959. The annual rainfall has ranged between a low of 23 in. and a high of 42 in.

Jan 1, 1969

By Thomas R. Stauffer

The principle that conventional schemes for taxing petroleum or mineral resources are "inefficient" is illustrated using simulation calculations tested against an "ideal" system. Inefficiency is defined as the relative success in maximizing expected government revenues from the resources. Most systems fail because: 1) they leave oil in limbo, i.e. unproduced because of excessive fiscal burden; or 2) they unnecessarily increase the variance in the explorationist'c, rate of return by undertaxing large fields and overtaxing smaller but infra-marginal fields. This increases his discount rate and reduces taxable surplus. An "ideal" tax system is specified which maximizes government revenues while minimizing risk to the operator. Two criteria are developed: 1) the tax falls to zero on fields which yield only the minimum necessary rate of return ("marginal" fields); and 2) the after-tax present value of all fields is the same for all fields above a threshhold size. In particular, marginal fields, while contrib- uting little to expected values, do contribute to reducing variance and hence risk praemia by distributing the exploration costs over a higher probability of successful outcomes.

Jan 1, 1982

By M. D. Banus, M. B. Bever, A. K. Jena

Measurements of the heat effects on addition of various solid phases of InSb to a solution calorimeter have confirmed the existence of a new high-pressure plzase InSbQII), which was jormed at 37 kbar and 623°K. The heats of formation of InSbQ), InSbfl), and InSb(111) have been measured and the heats of transjormation of InSb(1) to InSb(1l) and InSb(Iii) and of 'InSb(ll) to InSb(iiI) at atmospheric pressure and 78°K have been determined independently. Other thermodynamic properties of these phases, the phase boundary InSb(i)/InSb(ll), and the relative positions of the triple points are calculated. The pressure-Dolume term is shown to be more critical than the internal energy difference in making the phase InSbQ) less stable than InSb(II) at high pressures. Observations on partially transformed specimens suggest that the transformation of' metastable InSb (III) takes place in the two steps InSb(lll) — InSbQI) and InSbQI) — InSb(l). The compound InSb can exist as several phases depending on the temperature and pressure. The phase InSb(I), which is a semiconductor having the zinc-blende structure, transforms into the phase InSb(11) at a pressure of about 23 kbar and room temperature.'-3 The phase InSb(II) has the 6 tin structure,4-6 is metallic, and becomes a superconductor below 2.lok7 An orthorhombic phase of InSb has been reported to occur above a pressure of approximately 30 kbar at room temperature.' This phase is also a superconductor below about 3.4k9 The phase InSb(I1) is retained at atmospheric pressure if it is quenched to 78°K under pressure,6,7 but tends to transform at higher temperatures and does so explosively above approximately 210ok,7 A value of the heat of transformation of InSb(1) to InSb(II) at 210°K and atmospheric pressure has been reported.' A concurrent publication'0 reports evidence for a new solid phase InSb(III), which was formed by annealing InSb above 58 1°K at 37 kbar, above 560°K at 52 kbar, and above 473°K at 65 kbar. Specimens of InSb(II1) had a superconducting transition temperature of 4.lo ± 0.1oK. X-ray diffraction patterns also indicated the presence of a new phase. In this communication, thermodynamic properties of the phases InSb(I), InSb(II), and InSb(II1) are reported and discussed. The phase boundary InSb(I)/InSb(II) and the relative positions of the triple points are calculated. 1) EXPERIMENTAL 1.1) Preparation of Specimens. Specimens of the high-pressure phases of InSb were prepared in a belt-type high-pressure chamber by a tichnique described in detail elsewhere.'' Charges of 0.6 to 0.8 g of Cominco semiconductor grade InSb were used. The temperatures were measured with a chromel-alumel thermocouple, the hot junction of which was within 0.5 mm of the specimen. The specimens were heated under a pressure of 37 kbar for 1 hr at 723°K (which is well above the liquidus) and quenched to room temperature. One set was annealed at 523°K and another set at 623°K for 20 to 24 hr. These annealing temperatures were chosen because 523°K was below and 623°K was above the temperature of the transformation of InSb(II) to InSb(1Tl) at 37 kbar.10 The specimens were then cooled to 125°K by passing liquid nitrogen through the jacket of the belt die before the

Jan 1, 1968

By T. E. Davidson, A. P. Lee

It is known from the early work of Bridgman that the two lowest-pressure transitions (I-II and II-III) are accompanied by substantial and abrupt changes in resistivity and Volume. However, unlike the temperature -induced allotropic transformations observed in such elements as lithium, cobalt, tin, and so forth, there is little actually known about many of the characteristics of the pressure-in&ced transitions. This current work involves an examination of the structural and transformation characteristics of the bismuth I-II and II-III transitions under hydrostatic pressures. The relationship of initial structure to the transformation pressure, rate, resistivity change, and resultant structure is discussed. It is shown that the transition pressure and transformation rate are independent of the presence of grain boundaries and associated anisotropy-induced deformation. An observed hysteresis in both the I-II and II-III transitions is shown. BISMUTH is one of the most interesting of the elements exhibiting pressure-induced polymorphs since it undergoes several allotropic transformations at pressures below 90,000 atm. It is known from the early work of bridman1,2 that the two lowest-pressure transitions (1-11 and 11-111) are accompanied by substantial and abrupt changes in resistance and volume. However, unlike the temperature-induced allotropic transformations observed in such elements as lithium, cobalt, tin, and so forth, there is little actually known about many of the characteristics of these pressure-induced transitions. It is the purpose of this work to examine some of the structural and transformation characteristics of the bismuth 1-11 and 11-111 transitions under hydrostatic pressures. Another interesting characteristic of bismuth is that, in its polycrystalline form, hydrostatic pressures of sufficient magnitude will induce severe progressive plastic deformation in the region of the grain boundaries.3 This deformation, which has also been observed in several other metals, is attributed to the high degree of anisotropy in the linear compressibility of bismuth, resulting in shear stresses in the grain boundaries when it is exposed to hydrostatic pressure. Most thermally induced allotropic transformations in metals, whether of the diffusionless ather-ma1 (martensitic) or isothermal nucleation and growth types, are dependent upon structure and prior history,4 viz., grain boundaries, deformation, and so forth. One logically wonders then whether the transformation characteristics of the pressure-induced polymorphs in bismuth might also depend upon initial structure, particularly with respect to the presence of grain boundaries and associated plastic deformation. In this investigation, the role of grain boundaries and plastic deformation on the characteristics of the bismuth I-II and 11-111 transitions will be established. The rather unique residual microstruc-tural changes associated with these transitions will be presented and discussed. The occurrence of a measurable hysteresis in both the I-II and 11-111 transitions will be demonstrated. The type of transformation mechanism based on the observed transformation rate will be discussed. EXPERIMENTAL PROCEDURE A) Apparatus. The hydrostatic pressure system utilized in this investigation is similar to that previously reported by Bridgman' and Birch and Robertson,5 and has been previously described.3 For the purpose of this work, the pressure medium utilized was a 1:l mixture of pentane and isopentane. Pressure measurement was by means of a manganin coil in conjunction with a Foxboro Recorder. The manganin coil was mounted in the bottom closure and inserted inside the pressure cavity. Based on calibration against a controlled clearance piston gage at approximately 10,000 atm, the estimated error in the pressure measurement was +2 pct. Assuming the nonlinearity in the pressure coefficient of resistivity between 10,000 and 28,000 atm to be not greater than 1 pct, then the estimated error in the range of the I-II and 11-111 transitions was +3 pct. B) specimen Material and Preparation. The bismuth utilized throughout this investigation was of

Jan 1, 1964

By John P. Hager, Igor A. Wilkomirsky

The thermodynamic properties of the Pb-Ag system have been determined between 775° and 950°C by the cell: Electrotransport measurements on silica-saturated PbO-SiO2 melts established that the conduction was entirely ionic and that lead is present only in the divalent state. The activities of lead and silver exhibit Positive deviations from ideal behavior. In dilute solutions the activities of lead and silver follow Henry's law. The values obtained for yhb and yig at 1200°K are 1.49 and 1.69, respectively. Determination of a portion of the liquidus curve agrees well with the established phase diagram. provides an accurate means for the thermodynamic study of liquid alloy systems. However, Wagner and wernerl have shown that cells of type I are limited to alloy systems for which the reaction at the alloy-electrolyte interface will be extremely small. The traditional electrolyte for cells of type I has been a low melting point mixture of group IA chlorides, to which a small amount of the compound ACIZa has been added. However, the choice of a chloride electrolyte may not always be practical, in that the Gibbs free energies of formation of the compounds ACIZ, and BCIZb may not be sufficiently different to minimize Reaction [I]. On the other hand, the Gibbs free energies of formation of the oxides of metals A and B may be sufficiently different to minimize Reaction [I]. In this case, the use of molten oxide electrolyte would be clearly advantageous. In the present study, the thermodynamic properties of the Pb-Ag system have been investigated using the cell: Previous galvanic cell studies on the Pb-Ag system2'= are not reliable due to the displacement reaction between the alloys and the chloride electrolyte. Wagner and ~erner,' using Laitinen and Liu's' value at 450°C for the standard electrode potential of Reaction 111, have estimated the percent error in the activity of lead bPb) when using a chloride electrolyte. At 1000°C the error for xpb = 0.10 is 12 pct. Taking the Gibbs free energies of formation for PbClz and Ag cI,' and the equations of Wagner and Werner,' the error in apb at 1000°C and Xpb =0.10 was calculated to be 140 pct. However, using the Gibbs free energies of formation for Pb O' and an estimated value for Ag 20, the error in apb when using a molten oxide electrolyte at 1000°C was estimated to be less than 1 pct for The virtual reaction of cell I1 for the passage of n Faradays of positive electricity from left to right in the cell is: where 5 is the Faraday equivalent (23,063 cal per v equivalent), E is the electromotive force of the cell in volts, and n is the number of Faradays of electricity required for the transfer of 1 g-atom of lead through the cell. The value of n should be equal to 2 since lead is generally divalent in oxide melts. However, the presence of either tetravalent lead ions or electronic conductivity through the molten oxide electrolyte will result in a value of n greater than 2. Bockris, Kitchener, and Davies' have determined the amount of ionic conductance in a liquid PbO-SiO2 mixture (xPbO= 0.50) at 920°C by measurement of the volumes of CO and C& evolved at a carbon anode during electrolysis. From their data a value of 2.13 * 0.16 was calculated for n. Although their measurements indicate the possible presence of multivalent lead ions and/or electronic conductivity, their measurements were not at silica saturation and no definite conclusions can be drawn. However, as a result of the electrotransport measurements described in the next section the ;due of n can be taken as equal to 2.

Jan 1, 1969

By M. Prats

This paper presents a method for obtaining the correct values of the breakthrough sweep efficiency of the staggered line drive, taking into account the proper shape of the breakthrough streamline. Results obtained were different from those previously published, which were obtained by using an inexact shape of the breakrhrough streamline. INTRODUCTION In Section 9.31 of Muskat's' The Flow of Hotnogeticous Fluids Through Porous Media, it is stated that in a staggered line drive flood "the streamline of highest average velocity [is] the line of centers between input and output wells" (see Fig. I). Muskat used this concept to determine the relationship between the breakthrough sweep efficiency and the geometry of the staggered line drive pattern. Although it is clear from symmetry considerations that the breakthrough streamline passes through the midpoint between input and output wells, it is equally clear, as shown in Fig. 239 of Ref. 1, that the breakthrough streamline is not represented very well by the straight line joining the input and output wells. Therefore, it is desirable to determine the proper relationship between the breakthrough sweep efficiency and the pattern geometry by using the proper shape of the breakthrough streamline. METHOD OF SOLUTION It was found that the effect of the geometry of the staggered line drive on the breakthrough sweep efficiency can be investigated easily by making use of the method developed in Ref. 2. With this method, it can be shown that the general complex potential for the staggered line drive, which can be considered as a rectangular five-spot, is given in the coordinate system of Fig. 1, by O(z) = In cn(z\m) = +(x,y) + i $(x, y) . (1) where z = x + iy, +(x, y) is the potential distribution and $(x, y) is the stream function. The function cn (zm) is a Jacobian elliptic function of parameter m and has simple zeros at z,. = (2n + 1) K + 21iK and simple poles at z, = 2nK + (21 + 1)iK. Thus, the complex potential behaves like a(z) = ln(z - zr.) in the neighborhood of the production wells and behaves like a(z) = - ln(z - Z,) in the neighborhood of the injection wells. Since (z - z1.v) = rll.ei, we note that the potential + has the proper logarithmic behavior near the two wells, while the stream function $ varies with the angle, decreasing clockwise around the production well and increasing clockwise around the injection well. The functions K(m) and K'(tn), related by K(m) = K'(m,), where m + m, = 1, are known as the complete elliptic integrals of the first kind. By use of other properties of the Jacobian elliptic functions, the general stream function distribution for the staggered line drive can be obtained from Eq. 1: From the Jacobian elliptic function values, sn(0lm) = 0 dn(O(m) = cn(0jm) = 1, and f[K'(m)Iml = 03, it follows that the stream function given by Eq. 2 satisfies the proper symmetry conditions near a production well P located at [K(m), 01 and an injection well I located at [0, K' (m)]. That is, the line IOP in Fig. 1 is a streamline with value G (0. 0) = -0. and the straight lines connecting I and P to the point [K(m), K' (m)] is a streamline of value $[K(m), K' (m)] = -7/2. Similar symmetry conditions are obtained near other wells. It should be nuled that for m = m1, = 0.5, Eq. 2 reduces to the stream function distribution of the regular five-spot given in Ref. 7. SHAPE OF THE BREAKTHROUGH STREAMLINE It is apparent, from symmetry considerations, that the breakthrough streamline ($,) passes through the point [K(m)/2, K' (m)/2]. Its value there is so that the shape of the breakthrough streamline $,, is given by

Jan 1, 1957

By Paul L. Russell

THIS is a progress report of an experiment being undertaken in cooperation with the Bethlehem Steel Corp., the Crucible Steel Co., and the Rock Bit Sales and Service Co., involving heat treatment of the shank ends of drill steel. This experiment is being conducted by the U. S. Bureau of Mines in its experimental mine, Mining Research Branch, Bluemont, Va. The purpose of the experiment is to determine the effect of an increase in the time the steel soaks in the furnace during the hardening heat. It has been thought that increasing this time produces a soft zone below the lugs resulting in a metallurgical notch that causes early failure. Each of the steel companies furnished enough 11/4 - in. straight carbon, hollow, round steel to make up 10 sets of drill steel, in each instance the steel bars were from the same heat. These sets of drill steel, consisting of 2-ft, 4-ft, 6-ft, and 8-ft lengths were fabricated by the Rock Bit Sales and Service Co. Special attention was given to the forging of the steel to produce the best rods possible. The heat treatment of all thread ends was identical and followed the best practice. The heat treatment of the shank ends of five sets of steel from each company produced a soft zone 2 to 4 in. in front of the lugs. It was decided that possibly the best way to obtain this effect was not to overlap the hardening heat but to let the steel soak for an additional 30 min before quenching. Therefore the only variable in the test steels is the length of time the shank ends were in the furnace. The remaining drill steel shanks were treated as follows: Heat treatment in pyrometer-controlled furnace at 1550°F. Quenching oil at 105°F to 125°F temperature. Areas for heat treatment were; shanks, 11 in.; threads, 9 in. Time at heat, standard practice, 20 min for 11/4-in. steel. Actual drilling tests were made in greenstone, (a metamorphosed basaltic rock), and in epidosite. Greenstone has a specific gravity of 2.96 and a compressive strength of 44,200 psi. Epidosite has a specific gravity of 3.26 and a compressive strength of 63,100 psi. All drilling tests were made using a 31/2-in. column-mounted, automatic feed drifter, with a controlled air pressure of 90 psi at the throttle. Tungsten-carbide bits of 2 in. diameter were used for all drilling. Contrary to expectations the drill steels that were allowed to soak for the additional 30 min before quenching performed better than the steels that were heat treated according to standard practice. This performance, as shown in Table I, was especially noticeable in the drilling of epidosite. The "longheat" drill steels furnished by Company "A" drilled 154 pct more minutes than the "standard-heat" steel. Expressed in feet, the "long-heat" steel drilled 114.60 ft more before failure than the "standard-heat" steel. The "long-heat" steel furnished by Company "B" drilled 37 pet more minutes or 60.39 ft more before failure than the "standard-heat" drill steel. The effect of the long heat treatment was not as evident when the steels were drilling in greenstone (Table II). In greenstone, the increase in minutes drilled by the "long-heat" steel over the "standard-heat" steel was 47 pet and 1 pet, respectively, for Companies "A" and "B."

Jan 1, 1952

By Albert G. Anderson

I'm sure many of you have wondered what the term "Cross Flow Filtration" means. I shall explain it so that you more clearly understand it, and I hope you will be able to make it a useful tool for you in the future. In the simplest form of cross flow filtration contaminated fluid. or feed stream, is fed at a high velocity down the center of a porous tube, clear fluid weeps through the porous wall of the tube while the suspended solids concentrate in and are swept away by the feed stream. (See figure A). The high velocity flow of the feed stream tends to keep the inside of the tube free from a build up of contamination. By utilizing this cross flow approach to filtration, we have been able to concentrate such things as paint pigments, titanium dioxide, iron oxide, precipitated metals such as uranium yellowcake or silver, cadmium, some metal hydroxides, as well as gelatinous particles such as yeast cells. You will recognize that cross flow filtration lends itself to a recirculation loop system due to the necessity of maintaining a high velocity on the inside of the tube. This means that we generally have a storage tank from which we are recirculating, and the solids will concentrate in the storage tank. (See figure B). The storage tank design becomes an integral part of the total system and is very important to the total function of the system. The cross flow filter system requires only low pressure, and will work with centrifugal pumps, diaphram pumps or in some cases no pump at all. As an example, if we wanted to filter a 10 GPM (37.8 liters/min.) stream that contained 1% of submicronic particulate, we would flow the 10 GPM (37.8 liters/min.) into the storage tank and recirculate through the filter at a flow of anywhere from 30 GPM to 100 GPM (113.6 to 378.5 liters/min.) depending upon the filterability of the particles from the liquid. As the contaminated fluid recirculates, the solids will build up in the storage tank and loop until they reach a level, which is dependent upon the design of the tank. Then the settling rate in the tank becomes equal to the amount of the solids being fed to the tank, and as a result you reach an equilibrium in the amount of solids being presented to the inside of the porous tubing. We have in effect created a dynamic settling tank or thickener. A flow of 10 GPM (37.8 liters/min.) of clear filtrate comes off for either recycle or disposal with periodic removal of thick mud from the bottom of the tank. The thick mud can be either processed through a centrifuge, a rotary drum filter. a flat bed pressure type filter, or other means. Often the small volume of filtrate from the mud de-watering stream can be recycled back into the recirculation tank so that any fines in the feedback are again concentrated, thus closing the loop on the continuous process 100% removal system. Cross flow filtration will not do efficient molecular separation. We work primarily with discrete solids but we do separate them totally from the liquid carrier fluid. I know some of you will raise your eyebrows when I say that we remove 100% of the particulate, but in measurement tests, we have measured the filtrate cleanliness with instruments that record as low as .05 ppm and the instruments read zero, so that it is less than .05 ppm.

Jan 1, 1980

By Bunting S. Crocker

Bunting S. Crocker (Executive Vice President, Kilborn Engineering Ltd., Toronto, Ont., Canada)-This is an interesting report on laboratory-scale testing with pebble charges in 12-in.-diam mills, and the author correctly concludes that useful laboratory testing can be done. In the opening paragraphs he states, "laboratory pebble-milling tests have been considered too difficult to perform and not relevant enough to the actual grinding situation"!! This is definitely not so! The writer published detailed tests done in a 12-in.-diam mill comparing pebble and steel balls in 1952 6 and again in 1954 7. We note that our review paper in 1963 was the only one mentioned in the References. The author states that "a smooth lining is more frequently used in commercial-scale pebble grinding." The writer has designed some 22 plants treating 134,000 tpd in North America and Australia. He has also visited pebble installations in Norway, Sweden, Finland, and South Africa. All these plants correctly use heavier lifters than would be considered standard for ball mills of a similar size. Smooth liners are not recommended in wet ore treating plants. In the 1952 paper6 it was clearly demonstrated in the test work that the individual ore pebbles had to be the same weight-not the same diameter or size-as the steel balls if comparable grinding results were to be obtained. In the tests performed in this study most of the pebbles "passed 50-mm round hole screen openings and remained on a 40-mm round hole sieve. Correspondingly most of the ball mill experiments were performed with 50 or 40-mm steel balls". Thus, the balls and pebbles were essentially the same size or diameter. This means we are comparing apples and oranges. When the feed being ground is fine enough the pebbles will be superior. When the feed is coarse the steel balls will be the better. This is similar to grinding tests in which two sizes of steel balls are compared. In the middle of the article, "Crocker5 has reported that equal weights of pebbles and steel balls achieve the same grinding capacities under similar conditions …", then he proceeds to question this postulate. In the eight reports that I have published, I have never made this statement. What I have said is "for comparable grinding, the individual pebbles in the mill charge should be the same weight as the individual steel balls." This is not the first time that I have been misquoted on this point! It is most unfortunate that this test work has been done with a ball and pebble of the same diameter and not the same weight. It is impossible to properly evaluate the results. I also regret the fact that the screen analyses of the tests were not shown. Many of us who have been 40 years or less in the grinding game can easily read screen analyses at a glance. We can tell whether the top meshes are being ground by the ball charge, etc., etc. The graphs are fine for the summary or to illustrate conclusions but are often misleading in the report itself. However, we do agree that useful pebble grinding tests can be done in a 12-in. mill.

Jan 1, 1973

By C. S. Barrett

THE crystal imperfections known as faults in stacking (stacking disorder) are of importance to both fundamental and applied science and are receiving increasing attention. On the theoretical side there have been recent advances in the analysis of diffraction patterns in terms of stacking faults, and on the experimental side it has been found that certain metals develop a faulted structure on cooling through a phase transformation. Beyond this, little is known of what may be called the physical and mechanical metallurgy of faulting, although there has been no lack of discussion and conjecture as to the presence of faults in metals and the effect of faults on mechanical properties and microstructures. In the close-packed metals the nature of faults can be described very simply. Face-centered cubic (FCC) crystals consist of close-packed layers of atoms, (111) planes, stacked above each other in a definite manner. If one layer is designated as the A layer, the next must be a B or a C layer; that is, every atom of the second layer lies not above the atoms of the A layer, but nestles in the hollows between these, using the hollows designated as the B positions, or the equivalent hollows designated as C. If the sequence of layers is ABCABC...., so that layers three spacings apart are directly over each other, the crystal is FCC; if CBACBA ... it is an FCC crystal that is a twin of the former; if ABAB........or BCBC..it is hexagonal close-packed (HCP). A fault is a break in the sequence, such as ABCABABC .. . which has the effect of inserting an HCP lamella into an FCC crystal. Regularly spaced faults spaced two layers apart would convert an FCC crystal entirely to HCP, or an HCP to FCC. A fault in an FCC crystal is also equivalent to creating an FCC twin of minimum thickness; in fact, the entire crystal would be converted to its twin if faults were introduced regularly. (In HCP crystals, however, twinning does not occur on the basal plane and a fault on this plane is not identical with a thin twin). Faults are one of the possible causes for annealing twins,' for the strain markings that are brought out by etching deformed metal,'," for the altered X ray reflecting power of metal at slip bands that is revealed in X ray reflection micrographs,' for the extinction of Kikuchi lines in electron diffraction patterns, and for the hardening of latent slip planes.' Since other explanations of these effects are also available," there has been no direct proof of faults from deformation; yet it has appeared likely that they would occur. Faults resulting from phase transformations in metals, however, have been clearly revealed by diffraction in cobalt" and lithium. It is to be expected that the faulting tendency is greatest

Jan 1, 1951