Search Documents

By Edward J. Way

+1KLEINFONTEIN GROUP CENTRAL ADMlNISTRATION, BENONI, TRANSVAAL, S. AFRICA. The cost and the speed of sinking a shaft are factors of so great importance in operating a mine, that the data given in Table I., herewith published, will be of interest and value to all engaged in practical mining; and for this reason the data are communicated for permanent and accessible record in our Transactions. The figures 'of cost cover the period from January 1, 1903, to May 31, 1903, during which time the total depth sunk was 858 ft. So far as I know, the cost of sinking per foot (£13,15s., 11.04d.) of a shaft of the dimensions 21 ft. by 6 ft. in hard rock, is the cheapest yet on record; and the speed of 213.5 ft. per month, which was attained during May, 1903, is also the best record for speed in sinking in rock so hard as that of this shaft. During the period from January 1 to May 31, 1903, there were 144 rounds worked, involving 4,032 holes, of a total depth of 28,963 ft. 2.4 in., which is equivalent to an average depth of 7 ft. 2.2 in. per hole bored. These data are of added interest from the fact that the work was done practically by native labor.

Jan 1, 1905

By A. K. Jena, M. O. Bever

The thermodynamic behavior of dilute solutions of copper, silver, and gold in liquid tin is not explained by current solution theories.1-3 The relative partial gram-atomic enthalpies, or heats of solution, of silver, gold, and platinum in liquid lead at 623°K have been measured in the investigation reported here. Their interpretation requires a modification of the regular-solution theory although lead-rich solutions may be expected to be simpler than tin-rich solutions. The liquid metal solution calorimeter used has been described.4 At the start of a run the bath consisted of 621 g of reagent-grade lead. Several calibrating additions of lead were made during a run; a value of 3.48 kcal per g-atom5 was taken for H623°K - H273°K Two runs were made with each of the solutes silver, gold, and platinum. Annealed wire samples of 99.999+ pct purity were used. Four to six samples each weighing 0.5 to 1,0 g were added from 273°K to the bath at 623°K and the associated heat effects were measured. The samples dissolved in approximately 3 min. No serious experimental difficulties were encountered. The heat effects of the additions in a run plotted against the average atom fraction of solute before and after each addition314 were linear functions of the concentration in lead of silver, gold, and platinum, respectively. By subtracting the difference between the heat contents of a solute element at 623° and. 273°K5 from the measuredheat effects, the partial gram-atomic enthalpy relative to the solid solute was obtained. The relativ: partial gram-atomic enthalpy at infinite dilution and the concentration dependence of the partial gram-atomic enthalpies obtained from the plots of vs atomic fraction x are listed in Table I. The relative partial gram-atomic enthalpy at infinite dilution of silver in lead of 5.46 kcal per g-atom at 623°K compares with values at 723°K of 5.74' and 5.765 kcal per g-atom. These data yield a temperature coefficient of 3.0 cal per g-atom-OK. The partial gram-atomic enthalpy at infinite dilution of gold in lead at 623°K is 0.89 kcal per g-atom compared with 0.85 kcal per g-atoms (obtained by extrapolation) and 0.95 kcal per g-atom.5 By combining these values for 623°K with those for several other temperatures5" the temperature coefficient of was found to be 3.2 cal per g-atom-OK. No thermodynamic data are

Jan 1, 1968

The following is a list of members who died in 1928. It is compiled from reports to the Secretary's office. Biographical sketches published in Mining and Metallurgy are indicated in the last two columns. Issue Containing Year or Date or Biography Election Name Death 1928 Page 1914 Adams. David T.................... July 22 October 471 1905 Aguilera. Pedro................... May 3 October 469 1902 Althouse, H. W.................... NOV. 3 December 559 1920 Averill: C. C...................... July 9 October 471 1915 Baldwin, C. Kemble............... Aug. 9 October 471 1926 Barquist, Walter C............... NOV. 14 June 298 Barron,* Clarence Walker......... Oct. 2 November 511 1917 Beasley, Fred E.................... Aug. 31 October 471 1901 Belden, S. B....................... May 15 July 333 1927 Binney, Edwin, Jr.................. Dec. 29 February 96 1915 Bonsall, James Malcolm............ Feb. 12 June 284 1917 Boyle, John....................... July 12 December 561 1913 BradEn, Eugene B............. Jan. 29 March 157 1889 Bulkley, Frank.................... Mar. 25 May 240 1896 Callaghan, J. T., Jr............... Apr. 1 1892 Chalmers, George.................. Feb. 4 April 197 1898 Clark, Josiah H.................. May 7 July 333 1887 Copeland, F. K............. Nov. 10 December 561 1915 Cunningham, B. L11............... Dec. 6 August 294 1888 Dana, R. T........................ Aug. 20 December 559 1907 Dennis, Clifford G............... Dec. 28 March 1 1920 DeVenny, Thomas................ Feb. 13 April 197 1882 d'Invillier-, Edward V........... Jan. 4 March 157 1884 Duncan, M. M..................... Dec. 17 February 96 1924 Dyrssen, WaldemaR ............... Aug. 4 October 471 1906 Edmondson. H. W................ Dec. 21 February 1884 Emmerton, F. A.................. Oct. 9 June 298 1911 Eu, S. H............................ July 20 February 1917 Farrand, Ira W.................... Sept. 6 October 469 1900 Fell, E. Nelson...........•......... Mar. 25 May 231 1918 Fenton, Clarence M.............. October Junet 298 1908 Ferraris, Erminio................. Sept. 22 June 298 1914 Galloway. A. D. R............... December April 215 1924 Grant, A. W., Jr................... .4pr. 5 June 285 1917 Grant, Clifford G............... Jan. 26 January? 37 1918 Grant, Frank E.............. Jan. 14 September 417 1921 Gunderoth, C. J.................. Feb. 15 1897 Harms, Ernest..................... Aug. 12 November 512 1891 Hartrick, J. S..................... Feb. 9 June 285 1925 Hochschild, Berthold.............. Jan. 24 April 197 1917 Hutton, L. W...................... NOV. 3 January 37 1894 Jenning", S. J...................... NOV. 17 December 560 1925 Jones, J. Ravenscroft............... Jan. 29 March 157 1880 Jones, J. T......................... May 4 June 284

Jan 1, 1929

The Institute published a collective index of- Volumes I to XXXV inclusive, which has been very extensively purchased and used by the members of the Institute. It enables one to look, up any subject in the first thirty-five volumes and is useful to those who have the Transactions, as well as to those who have not, because it tells what subjects have been treated and enables one to look these matters up in his own library and then afterward either to procure the individual papers from the Institute at the price of $1 each, or to procure Volumes, or to consult the Trans-actions at a nearby library, if such a one is available. It now seems desirable to publish another collective index, and the Editorial Department, upon the authority of the Board of Directors, has prepared an index of Volumes XXXVI to LV inclusive. This will be sold in the Institute's standard half morocco binding at a price of $5 and in paper covers at a price of $4. It wilt be ready in a few weeks. Those who already have the first index and purchase the second one, and those who purchase both, will have a complete index of the Transactions from Volumes I to LV inclusive. The Institute will be glad to receive advance orders for this index to insure prompt delivery upon publication.

Jan 8, 1917

By R. W. Raymond

The important question of the metallurgical value of the coals of the Rocky Mountains and the Pacific Coast is to be settled, of course, by practical experiment. Meanwhile, as I have had occasion to point out, the proximate analyses of these coals throws little light upon it, and is, indeed, likely to mislead the metallurgist, if he compares it with the results of similar analyses upon bituminous and semi-bituminous coals. With the view of showing how large a proportion of the material usually classed as(" volatile matters " consists of combined water, or oxygen and hydrogen presumably in chemical combination, I have collected a number of ultimate analyses from various sources, in the following tables. The numbered analyses in the first table are as follows: No. 1. Monte Diabolo coal—Analyst, H. S. Munroe, Col. School of Mines. 2. Weber Canon, Utah, " " " 3. Echo Canon, " " " " 4. Carbon Stat'n, Wyoming, " " " 5. " " " " " 6. Coos Bay, Oregon, " " " 7. Alaska, " " " 8. " " " " 9. Canon City, Colorado, " Dr. T. M. Drown, Philadelphia. 10. Baker Co., Oregon, " " " 11. Blockcoal,SandCr'k,Ind., " Prof. E. T. Cox. This table affords some suggestive comparisons, to facilitate which a remark or two, explanatory of its construction, will be useful. In the ultimate analysis of coals, the proportions are frequently calculated (as, for instance, in the report for 1872 of Prof. Cox, State

By Perry Harrison

THE increased use of sintering for the beneficiation of iron ores and the reclaiming of flue dust creates a lively interest in sintering costs and, economics. The character of material sintered and geographical location of plants so radically alter sintering costs and economics that it is well to understand at least the basic elements which control such changes. The following cost factors are believed to be roughly approximated for large-scale Dwight-Lloyd 'continuously operated sinter-machine installations located anywhere. PER CRUDE TON Labor, supplies and repairs 0.15 Power 6.5¢ X kw-hr. rate ? Plant overhead and administration 0.05 Depreciation per ton annual capacity 0.05 Fuel: 6 per cent coke breeze or equivalent minimum ? 1 per cent coke breeze additional for each 5 per cent free and combined water in ore or dust ? Ignition distillate at 0.6 gal. per ton ? PER SINTER TON Royalty on Ore 0.10 Royalty on Flue Dust 0.15 PER CRUDE TON "Winter expense"; i. z., the cost of the five months enforced idle . period for plants tied in to Great Lakes transportation season 0.03 Using the foregoing data, it is possible to roughly approximate the cost of efficient sintering at any location for. any ore, viz:

Jan 1, 1932

One-half fare return rate again available to members of the Institute and dependent members of their families. DON'T FORGET YOUR RAILROAD CERTIFICATE Over 300 members of the A. I. M. E. and dependent mem-bers of their families attending the last annual meeting se-cured return railroad tickets at half price by means of the railroad certificate, thereby saving several thousand dollars. DIRECTIONS 1. Be sure to obtain your railroad certificate when pur-chasing your railroad tickets for the meeting or you will lose money. 2. Purchase your tickets at regular one-way adult tariff fare between the dates specified for your territory in the accom-panying table. 3. Present your certificate for valida-tion at Institute headquarters in New York immediately after registration. Certificates will be validated on Feb. 21 and 22 between 9 a. m. and 5.30 p. in. 4. You must use your return half-rate tickets not later than Feb. 27. 5. Use the same route for both going and return trip. PLEASE REMEMBER THIS 1. Unless-250 certificates are validated at headquarters it will be impossible for anyone to secure the reduced rate. 2. Unless you secure a certificate you cannot take advantage. of the half-rate return fare, even if the necessary 250 certificates are validated.

Jan 2, 1928

By Zay Jeffries

This paper will include a brief discussion of Prof. Howe's paper on The Supposed Reversal of Inheritance of Ferrite Grain Size from that of Austenite.l The general subject of grain refining in steel and iron will also be treated. The conclusions reached are stated in the following hypotheses which are discussed more in detail below. 1. The ferrite grain size in pure iron, the ferrite and pearlite grain size in hypoeutectoid steel, the pearlite grain size in eutectoid steel and the cementite and pearlite grain size of hypereutectoid steel are not inherited from the grain size of the mother austenite. 2. The only structural feature that is generally inherited from the austenite of hypo- and hypereutectoid steels on cooling through their transformation ranges is the position of the excess ferrite or cementite at the austenite grain boundaries, sometimes causing complete and sometimes incomplete networks which outline the old austenite grain boundaries. Rapid cooling through the transformation range will cause the non-inheritance of this structural (network) feature. 3. The austenite grain boundaries themselves are nearly always effaced in all steels and also in pure iron during the At transformations. 4. The grain-size refining of steel and iron is brought about by the combined effect of non-inheritance of the transformation products on either heating or cooling, i.e., the austenite transformation products do cst inherit their grain size from the austenite on cooling through the transformation range nor does austenite inherit its grain size from the products which form austenite on heating. 5. In general, in both iron and carbon steel the larger the austenite grain size, the larger will be the grain size of the transformation products on cooling. This, of course, assumes all other conditions constant except the austenite grain size. An exception is found to this general rule in very pure iron such as electrolytic iron. In this instance small austenite grains may form very large ferrite grains on cooling through Arg.

Jan 1, 1918

By Fred Bond

This paper is a continuation of two earlier papers,1,2 and presents new data on the grindability of various ores and other materials-the results of several years of intermittent research work on the nature of grinding and interpretation of test results. It is divided into five parts: 1. The tabulated results of several hundred grindability tests on a wide variety of ores. 2. A method of correcting screen analyses and calculating from them the surface and other properties. 3. A description of a. new method of measuring the "surface energy" of in ore by pendulum impact tests. 4. Test results. 5. A general discussion of the test results and their application to grinding problems.

Jan 1, 1938

By HORACE V. WlNCHELL

Location. THE St. Helens mining-district, indicated in sketch-map, Fig. 1, is chiefly in Townships 9 and 10 North, Ranges 5 and 6 East, of the Willamette meridian, in Skamania county, Wash. There is no railroad or even a wagon-road at present connecting it with any base of supplies; access is usually by wagon-road for FIG. I.-SKETCH-MAP OF THE STATE OF WASHINGTON. about 50 miles from the town of Castle Rock to Spirit lake, and from that point by pony-trail from 6 to 10 miles farther. History. Nearly 20 years ago two German farmers, totally inexperienced in prospecting, penetrated this region upon a hunting and fishing-trip. Their attention was drawn to numerous joints and crevices filled with black, glistening tourmaline, and con-

Oct 1, 1912

By C. S. Barrett, O. R. Trautz

PREVIOUS investigations have shown that lithium is body-centered cubic from near its melting point to the temperature of liquid air1,2,3 Nevertheless there was an incentive to search again for a transformation at low temperatures: C. Zener4,5 has remarked that the low value of the elastic modulus (11 - C12)/2 of body-centered cubic metals and alloys implies a rapid increase in free energy with decreasing temperature, which would favor the occurrence of a transformation; also the shear movement to which this modulus applies is one that can transform a body-centered cubic structure into a slightly distorted face-centered cubic structure. It was confirmed that lithium does not transform spontaneously at liquid nitrogen temperature, but it was found that a transformation can be induced at this temperature by cold working the metal,6 and at slightly lower temperatures a different transformation occurs spontaneously. Transformations were also found in solid solutions of magnesium in lithium. THE NATURE OF THE TRANSFORMATIONS Before presenting a detailed treatment of the technique used and the specific data obtained, it would be well to give a brief survey of the general characteristics of the transformations. A new crystal structure begins to form spontaneously in a specimen when it is cooled below a critical temperature. In lithium the structure appears to be close-packed hexagonal; in the Li-Mg alloys most of the diffraction lines (but not all) are near those for hexagonal lithium. The transformation proceeds as the temperature is lowered and soon stops if the temperature is held constant or raised. The course of the transformation on cooling is indicated by the curve at the lower left of Fig I. This curve is drawn in stepped fashion because the transformation goes by discrete steps with audible clicks. Because of the similarity to the decomposition of austenite into martensite in steels, it seems appropriate to designate the beginning of the spontaneous transformation on cooling as the Ms point. On heating to room temperature after the low temperature treatment only the usual BCC structure is found. On heating, the low temperature modification begins to disappear at a temperature which will be designated as Ac. The transformation on heating is halted when the rise in temperature is halted. The temperature must be raised 40 to 50°C above Ac before the reversion is complete-an interval which is sensitive to the rate of heating and to the time of holding at temperatures above Ac. This behavior on heating thus has similarities also to the formation of martensite in the cooling of steels.

Jan 1, 1948

By C. W. Allen, L. C. Moore

THE Mather mine, of the Negaunee Mine Co., is within the limits of the City of Ishpeming, on the Marquette iron- range in Michigan's Upper Peninsula. It is named for William G. Mather, who has served as President, and Chairman of the Board, of The Cleveland-Cliffs Iron Co. for well over 50 years. The property comprises nearly the square mile of section 2, T.47 N. R.27 W., which, except for 20 acres in the northeast corner, was leased by The Cleveland-Cliffs Iron Co. to the Negaunee company. The latter is a partnership of Cleveland-Cliffs and the Bethlehem Steel Co., organized to equip the property, retaining Cliffs in charge as operator. Shipments of ore from this area are mainly through Marquette, which is 16 miles to the northeast on Lake Superior, or through Escanaba, a Lake Michigan port, 65 miles to the south. Cleveland-Cliffs, in 1943, operated 12 mines in the Lake Superior district, with shipments of 6,635,576 tons for the year. GEOLOGY The north footwall of the Marquette Range synclinorium outcrops near the north line of sec. 2, the iron formation dipping to the south at an angle of about 40º. The south side of the trough reappears at a distance of 4 ½ miles on sec. 26 and the surface geology between shows iron formation or intrusive diorites. The latter are harder than most phases of the iron formation and, as a result of glacial action, appear as buttes or low-lying hills. The general elevation of sec. 2 is about 1450 ft. above sea level, or 850ft. above Lake Superior, and the higher diorite outcroppings about 1600 ft. above sea level. The geological structure has been complicated by a series of major and minor faults, one of which may be illustrated by the diorite sheet, which tilts south with the iron formation in the north half of the section and then reappears near the center to repeat this sequence. Sectionally the geological series includes a nearly eroded capping of Goodrich quartzite followed by the considerable thickness of Negaunee iron formation, which is cut by intrusive dikes or diorite sheets, and underlain by the Siamo slates grading into quartzites. The ore deposits occur mainly in troughs formed by the intersection of impervious dikes and the footwall slate, but include locally enriched lenses or bands in the iron formation and also interbedded with the Siamo slate. The ore is a soft red hematite with an indicated dried analysis from the surface drilling to date of 61.50 per cent Fe, 0.134 per cent P, 5.40 per cent Si, 2.87 per cent Al and 0.015 per cent S. EXPLORATION A diamond-drilling campaign started in 1937 actually had its inception in 1917, when a number of shallow test holes were put down for the purpose of locating ore that might be quickly developed and mined

Jan 1, 1945

By S. E. Szasz, E. J. Moore, B. F. Whitney

An accurate value of formation water resistivity R, is essential in calculating formation porosity and fluid saturation from electrical well logs. In the cases where R, has not been measured directly, it must be obtained from other data, e.g., the SP curve. This paper deals with another approach: how to calculate R, from the chemical analysis of the formation water. INTRODUCTION It is known that the resistivity of aqueous solutions of pure salts depends on their concentration and on the temperature; the concentrations are given in MPL (mg of solute per liter of solution), or sometimes in ppm (mg of solute per kg of solution): MPL = ppm X specific gravity. Values for different pure salts are available in the literature, but not for solutions of mixtures which are of practical interest. The major component of the dissolved material in almost all formation waters being sodium chloride, it is customary to express the resistivity of formation waters in terms of equivalent sodium chloride concentration, i.e., the concentration of a solution of pure NaCl which has the same resistivity at a given temperature as that of the formation water under consideration. Thus, the problem of calculating R, from the chemical anaylsis can also be stated as how to convert the other constituents of the solute into equivalent NaCl concentration. Salts dissolved in water are at least partly dissociated into ions, and do not conserve their identity. If known amounts of several salts are dissolved in water, the solution does not necessarily contain the same salts in the original proportion, but perhaps some other combination of the ions, along with free ions in solution. This is why the chemical analysis of formation waters is often given in terms of ions, as if all dissolved salts were completely dissociated. Our problem then boils down to how to convert the concentrations of the various ions to equivalent concentrations of Na' and C1-. Dunlap and Hawthorne' have proposed to convert the concentration of all other ions to equivalent Na' and C1-concentrations by means of constant multipliers; e.g., 0.95 for Ca"; 2.0 for Mg"; 0.27 for HCO 3-; 0.5 for SO, -, etc. Their factors were based on measurements made at 68F on 26 formation water samples from the Texas Gulf Coast, ranging in concentration from 1,500 to 75,000 ppm. The Dunlap method is widely used in electric log interpretation, and is often extrapolated beyond its original concentration range. A comparison of R, values calculated by this method and values actually measured on formation water samples has shown large discrepancies, especially at higher concentrations. Therefore, two new methods were developed at Sinclair Oil Corp.'s Tulsa Research Center to calculate equivalent sodium chloride concentration from the chemical analysis of formation water samples. FUNDAMENTAL CONSIDERATIONS The resistivity of a solution, or its reciprocal the conductivity, at a given temperature is determined by the charge, concentration and mobility of the ions actually present. Monovalent ions such as Na' or C1- always carry the same charge. Compounds of polyvalent ions, however. may show incomplete dissociation, e.g., NaSO; + Na' instead of SO,-- + 2Na'. This happens especially in more concentrated solutions. Only very dilute solutions are completely dissociated, as assumed in the chemical analysis report. At higher concentration, the degree of dissociation depends not only on the nature and concentration of the particular salt under consideration but also on the nature and concentrations of the other solutes. Mobility of the ions depends on the viscosity of the solution. It also depends on the degree of hydration of the ions, which in turn is a function of the nature and the charge of the ions and also of the amount of free water available per ion, i.e., the total ionic concentration. The net effect is that the conductivity increases slower than proportional to the concentration, even if a solution contains only one salt such as NaC1, and is different for different salts (Fig. 1). Conductivity can even decline with a further increase in concentration, e.g., if additional salt is little dissociated but ties up some of the free water and/or causes an increase in viscosity. In solutions containing more than one salt, the contribution of one salt to the total conductivity depends not only on the fractional concentration of this same salt, but also on the concentration of all other solutes. A perfect method would give the conductivity or resistivity of a solution as a function of the concentrations of all solutes present. This is so complicated as to be impractical, and a simpler method must be found which is of acceptable accuracy. The Dunlap method, on the other hand. is too simple because it askmes that at any concentration the contrih-

Jan 1, 1967

By David L. Holt

It is well-established that hydrostatic pressure distribution is hardly achieved during uniaxial compaction of powders. All the previous investigations1-4 give consistent results and this variation is attributed to the die-wall friction. The conclusions are based on measurements of the density of very small portions of the compact. Although the analysis of the density or the strain distribution in the compact is very helpful in obtaining information about the stress distribution within a powder compact, it does not describe the problem from a more fundamental point of view. The densification in metal powder compacts takes place chiefly by plastic deformation (ignoring particle rearrangement) at the points of contact of the powder particles. The onset of yielding and subsequent growth of the contact areas (for spherical powders) take place fixed by a constant stress equal to three times the yield stress in tension or compression,5-7 assuming little or no work hardening. Therefore, by deforming spherical powders in the die and measuring the contact areas on each particle, the load at each contact point can be determined. In the present investigation, this was done by hot-pressing uniform spheres of lead, K-Monel, and sapphire. The details of the experiment have been described elsewhere.' The spheres were studied for the size and the number of contact points on each particle using a specially designed goniometer. It was found that the deformed faces that were approximately normal to the direction of pressing were about 2.2 times larger than those parallel to the direction of pressing. Fig. 1 shows the typical deformed sphere. A detailed study showed that the mean value of the contact areas on each sphere was within 5 pct for all the spheres in the die (ignoring those touching the die walls and the top and bottom of the die).' The spheres touching the die walls and the top and bottom of the die were found to have larger contact areas (8 to 10 pct) which indicates higher pressures in these regions of the compact and thus higher compact densities in these regions. These results show that density distribution calculated from such an experiment will give results consistent with the previous investigators. It is concluded, therefore, that the pressure distribution in the die is better understood by studying contact areas on each particle. 'R. Kamm, M. A. Steinberg, and J. Wulff: Trans. TMS-AIME, 1947, vol. 171, p. 439. 'Pol Duwez and Leo Zwell: I. Metals, 1949, vol. 1, p. 137. 'G. C. Kucynski and I. Zaplatynskyj: Trans. TMS-AIIME, 1956, vol. 206, p. 215. 'R. P. Seelig and J. Wulff: Trans. TMS-AIME, 1946, vol. 166, p. 492. 'H. Hencky: Z. Angew. Math. Mech., 1923, vol. 3, p. 241. "J. Ishlinsky: I. Appl. Math. Mech. USSR, 1944, vol. 8, p. 233. 'D. Tabor: Proc. Roy. Soc. (London), Ser. A, 1948, vol. 192, p. 247. 'Ashok K. Kakar and A. C. D. Chaklader: 1. Appl. Phys., 1967, vol. 38, p. 3223. Superplasticity in 60Zn-40Al David L. Holt THE occurrence of superplasticity in Al-Zn alloys is of interest because of its possible industrial exploitation.' The eutectoid composition (78Zn-22A1) has been the most extensively studied;'-= neck resistant flow and high strain rate sensitivity of flow stress (characteristic of superplasticity) are associated with a micron-size grain conferred on the alloy by an homo-genization and quench.5'6 Compositions away from the eutectoid have received comparatively little attention, especially from the viewpoint of relating the structural

Jan 1, 1969

By Ernest Burchard

A RECONAISSANCE of the chrome and manganese'1ore deposits of Culm was made in the spring of 191s by Albert Burch representative of the U. S. Bureau of Mines and the writer representing the U. S. Geological Survey. The object of the study was to obtain authentic information for use of the: United States Government as to the location, character, size, and availability of the Cuban deposits of the ores of these important steel-alloy metals. The Cuban Government courteously detailed Sr. E. I. Montoulieu, a mining engineer connected with the Treasury Department, to act as escort and associate throughout the work on the Island. Mr. George A. Wright, of Baracoa, Cuba, a mining engineer especially familiar with the chromite deposits of Oriente Province, was a member of the party from Feb. 25 to Mar. 20. It was possible to visit most of, the chrome-ore deposits that seemed to be of promise, but there was not sufficient time to visit all that were brought to our attention, some of which may have merit. Furthermore, no attempt was made to examine the extensive chromiferous iron-ore deposits of the Mayari, Moa, and Cubitas districts, as these deposits cannot be regarded as sources of chromium except indirectly. At the close of the field work the essential data concerning the quantity and quality of ore probably available for shipment during 1918 and 1919, in the event of the continuation of the European war, and of the tonnage of ore in reserve, were furnished to such Government bureaus as were interested, including the Shipping Board and the War Industries Board, and as soon as chemical analyses of the chrome ores could .be obtained, a press bulletin on the subject was published by the Geological Survey. In the present paper the engineering data, and tonnage estimates contained in the unpublished notes of Mr. Burch have been freely used, and their helpfulness is hereby gratefully acknowledged. Many thanks are due Senor Montoulieu and Mr. Wright for their valuable work in the field; to the officials of the Spanish American Iron Co. and of the various other companies; and to individuals holding chromite claims, for courteously facilitating the work of the party. In the study of material for the present paper, chemical analyses have been made by R. C. Wells and petrographic determinations and descriptions were furnished by Miss E. F. Bliss, both of the U. S. Geological Survey.

Jan 9, 1919

By Arthur T. Allen

THE Kingsport formation, a part of the Knox dolomite of Ordovician age, is composed of 538 ft of dolomitc and limestone. Numerous bands, layers and nodules of chert, arenaceous and shale zones are present. The characteristics displayed by these features have been useful in mapping, prospecting and mining. Perhaps a better understanding of the origin of these zones will increase their usefulness. Introduction The presence of numerous bands, nodules, and irregular bodies of chert within the Kingsport formation in the Mascot locality has long been recognized. Oder and Miller1 mention the general characteristics, but do not deal with the chert occurrences in detail. When the occurrence of chert is studied in fresh exposures underground, a variety of characteristics is noted which has been useful in correlation and in detailing the sub-surface stratigraphy. Although the writer has no desire to enter into a controversy over the origin of chert, many observations have been made of its local characterigtics. A detailed stratigraphic section is included which shows the position of the individual horizons discussed in the following paragraphs. The term "chertification" has been adopted from Fowler and Lyden2 for use here. It refers to the replacement of lime- stone by introduced silicic acid. The writer uses it to refer to the occurrencc of introduced or original chert in limestone and dolomite. In this writing "syngenetic chert" refers to chert which has been deposited contemporaneously with the enclosing limestone or dolomite. Also, it is considered to include interstitial silica shown by chemical analysis and insoluble residues. The term "epigenetic" is applied to all chert which has been introduced after consolidation of the rocks in which it occurs, regardless of the nature of the depositing solutions. Syngenetic Chert It is the belief of the author that a large percentage of the chert found in the Kingsport formation is syngenetic. The widespread occurrence of similar nodules and bands of chert in the same horizon far from one another and far from areas of deformation or alteration of the enclosing rocks is difficult to explain by infiltration of the silica after compaction of the enclosing rocks. When chert of this type does occur near zones of movement it is likely to be involved in faulting and brecciation which indicates that it was deposited prior to deformation. Older Epigenetic Chert There are several occurrences of nodules in the Kingsport which seem to be epigenetic as pointed out in the following examples: A cherty zone occurs 26 ft above the o bed (Fig =). This is not always present but is found in the greater part of mine work-

Jan 1, 1949

By Arthur T. Allen

THE Kingsport formation, a part of the Knox dolomite of Ordovician age, is composed of 538 ft of dolomitc and limestone. Numerous bands, layers and nodules of chert, arenaceous and shale zones are present. The characteristics displayed by these features have been useful in mapping, prospecting and mining. Perhaps a better understanding of the origin of these zones will increase their usefulness. Introduction The presence of numerous bands, nodules, and irregular bodies of chert within the Kingsport formation in the Mascot locality has long been recognized. Oder and Miller1 mention the general characteristics, but do not deal with the chert occurrences in detail. When the occurrence of chert is studied in fresh exposures underground, a variety of characteristics is noted which has been useful in correlation and in detailing the sub-surface stratigraphy. Although the writer has no desire to enter into a controversy over the origin of chert, many observations have been made of its local characterigtics. A detailed stratigraphic section is included which shows the position of the individual horizons discussed in the following paragraphs. The term "chertification" has been adopted from Fowler and Lyden2 for use here. It refers to the replacement of lime- stone by introduced silicic acid. The writer uses it to refer to the occurrencc of introduced or original chert in limestone and dolomite. In this writing "syngenetic chert" refers to chert which has been deposited contemporaneously with the enclosing limestone or dolomite. Also, it is considered to include interstitial silica shown by chemical analysis and insoluble residues. The term "epigenetic" is applied to all chert which has been introduced after consolidation of the rocks in which it occurs, regardless of the nature of the depositing solutions. Syngenetic Chert It is the belief of the author that a large percentage of the chert found in the Kingsport formation is syngenetic. The widespread occurrence of similar nodules and bands of chert in the same horizon far from one another and far from areas of deformation or alteration of the enclosing rocks is difficult to explain by infiltration of the silica after compaction of the enclosing rocks. When chert of this type does occur near zones of movement it is likely to be involved in faulting and brecciation which indicates that it was deposited prior to deformation. Older Epigenetic Chert There are several occurrences of nodules in the Kingsport which seem to be epigenetic as pointed out in the following examples: A cherty zone occurs 26 ft above the o bed (Fig =). This is not always present but is found in the greater part of mine work-

Jan 1, 1949

By F. E. Lathe, L. Hodnett

This paper summarizes extensive data supplied by 40 copper converter plants in 18 countries, and includes a partial analysis and comments on the effect of converter slag composition and temperature on the fomzation and elimination of magnetite and the life of basic and neutral refractories. APRELIMINARY draft of this paper, including data from 26 companies which had submitted replies to a questionnaire, was presented at the Annual Meeting of the AIME held in New York in February, 1956. Publication was delayed in the expectation that additional replies would be received, and justification for the subsequent delay may be found in the fact that the present revised paper contains data from 40 converter plants situated in 18 different countries. The suggestion that a questionnaire be sent to the major copper and copper-nickel plants outside the U.S.S.R. and associated countries arose at the Los Angeles Annual Meeting in February, 1953, where several papers dealing with converter construction and operation were presented. In private discussions which followed, a group of metallurgists and refractories engineers raised the question why practices varied so much at different plants. Why did magnesite brick give superior service to chrome-magnesite in some plants but chrome-magnesite prove superior in others? Would metallurgical studies point the way to the development of still better refractories? Could magnetite formation be prevented in converter slags and reverber-atory furnace mattes? If this was feasible, why was a heavy circulating load of magnetite tolerated, when, in all probability, it increased copper losses in the reverberatory slags and, in some cases, made it necessary to shut down the furnaces periodically to clean out the accumulated magnetite? Was the sole purpose of coating brick with magnetite that of

Jan 1, 1959

By Samuel S. Wyer

THE installation of the gas-producer power-plant in America has been so unusual that all engineers have viewed it with in¬terest; a large majority, however, regard it with a lack of con-fidence and many with positive distrust. Despite the fact that European engineers have usually been less inclined to take the initiative along experimental lines than are Americans, they have, nevertheless, developed the gas-producer plant to a very high state of efficiency to which they were forced by the neces¬sity of economy in fuel-consumption. The gas-producer power-plant is so common in Europe that engineers as well as the general public regard it with the same degree of confidence that is now universally placed in steam¬plants. Gas-engines, both small and large, are in general use there, and central stations, aggregating several thousand horse¬power, are quite numerous. The fact that gas-producer power-plants have received so little attention in America may be attributed to five conditions:-1', ignorance and prejudice; 2, newness of work; 3, in-

Mar 1, 1905

By Earl E. Hunner

At the end of the year 1914, the main North Star incline shaft had reached the 6300-ft. level, and encountered a vein dipping southwest, or exactly opposite to the North Star. Subsequent development failed to find the North Star vein continuing beyond this intersection, so the 6300-ft. level proved to be the bottom level of the North Star vein, and very little ore was found below the 5300-ft. level. The new vein was called No. 1 vein. Development work carried on for the next 10 years discovered a third vein, called No. 2, branching off about 1200-ft. to the east, with a north-south strike and a west dip. No. 1 vein had about 900 ft. of backs above the 6300-ft. level before reaching the boundary line of the property, and No. 2 vein died out about 800 ft. above. During these 10 years, the money spent on development was increased from $54,000 in 1914 to $184,000 in 1924; the ore reserves steadily diminished until it was evident that the mine must close down unless by some means a large tonnage of ore could be developed quickly. Problems and Plans In order to understand what follows, the general layout and equipment of the mine as it was at this time must be briefly described. Fig. 6 indicates the relative positions of the shafts. The North Star (incline) shaft extends from the surface to the 6300-ft. level following the vein, with an average pitch of 26", between limits of 11" to 38. There is at present no hoisting equipment in this shaft between the 2700 and 4000-ft. levels. The Central (vertical) shaft connects with the North Star shaft at the 4000-ft. level, at a vertical depth of 1600 ft. In two compartments of this shaft 4-ton skips made a vertical turn of 15 ft. radius at the 4000-ft. level and ran down the incline to the 6300-ft. level. A cage operated in the third compartment to the 4000-ft. level. Men and supplies were transferred to a truck running on a third track down the incline shaft to the 6300, operated by an electric hoist on the 4000-ft. station. When the shifts changed double-deck cages were substituted for the skips in the vertical shaft, but they stopped at the 4000-ft. station. The truck to 6300 carried 22 men, and it required 8 min. to make a trip down and back. This arrangement was satisfactory as long as a fairly large proportion of the work was

Jan 1, 1930