Search Documents

By T. A. Read, H. K. Birnbaum

STRESS-induced twin boundary motion in the AuCd ß'phase (52.5 at. pct Au 47.5 at. pct Cd having an orthorhombic structure (space group D h)' was discussed for the case of transformation twins.' Mechanical twinning, i.e., introduction of new twin orientations by the applied stress was sometimes observed in the ß' phase which contained two transformation twin orientations. (See Ref. 2 for experimental details.) The transformation twins terminated at the mechanical twin boundary; the two initial orientations having been twinned to the new orientation as shown in Fig. l. In a "hard" tensile instrument, formation of each mechanical twin was accompanied by a sharp drop in load (and an audible click) resulting in a typical serrated load-extension curve. The mechanical twins increased in width and additional twins were nucleated as the load increased until the entire specimen was occupied by the mechanical twin orientation. A restoring force2 caused the mechanical twin and transformation twin boundaries to return towards their initial configuration on releasing the load. In a stabilized specimen* the total strain introduced by mechanical twinning was recovered on releasing the applied stress. Initial and final microstructures were identical. After decreasing gradually to a critical width, mechanical twins suddenly disappeared accompanied by audible clicks and sharp increases in load (measured at a constant rate of crosshead motion in a "hard" machine). Mechanical twins could be stabilized in any position by maintaining the applied load for a sufficient time, indicating a decrease in restoring force with time similar to that observed for transformation twins.' Orientation relationships for mechanical and transformation twins were determined and are shown in Fig. 2. The mechanical twin, T3, was twin related to transformation twin, T,, by reflection in (1ll), and twin related to transformation twin, T2, by reflection in (111)T, . T, was related to T, by reflection in(ll1)T1 . The "average" mechanical twin composition plane lay several degrees from (1ll), . In every specimen which mechanically twinned, orientation T3 was most highly favored by the applied stress, i.e., it was the twin orientation which provided the greatest change in length compatible with the direction of applied stress

Jan 1, 1961

By Dix, E. H.

THE percentage of manganese used in commercial aluminum alloys is small, and yet this element is an important addition to some very valuable alloys. When used alone with commercial aluminum containing iron and silicon as impurities, the usual percentage in wrought materials is from 1 to 1.5 per cent., whereas castings may contain as much as 2 per cent. An aluminum-manganese alloy containing nominally 1.25 per cent. manganese is much used in sheet form for the manufacture of cooking utensils and other articles requiring a little greater strength and hardness than could be obtained with commercially pure aluminum. It is also used for various purposes in the form of rods, tubes and pipes. The aluminum-manganese alloys, both wrought 'and cast, offer excellent resistance to many kinds of corrosion attack. The U. S. Naval Gun Factory uses an aluminum alloy containing from 1 to 2 per cent. each of copper and manganese, for both castings and forgings. Manganese is also used, up to about 1 per cent., as a minor alloying .element in several of the strong aluminum alloys of the duralumin type. It is felt that the role of this element when thus used has not been fully understood, but it is believed that the results obtained in this investigation will throw additional light on the subject. The earlier work on the system aluminum-manganese was general in nature, and no detailed investigations of the relations existent in the useful aluminum-rich alloys have been reported. Guilletl1in 1902 surveyed the system, and Hendrichs2 in 1908 published an equilibrium diagram which, although based on .few data, is often used in the literature. Fragmentary work has also been done by other investigators."

Jan 1, 1927

By Raymond F. Gray, Victor J. Hoffman, Richard J. Bagan, Harold L. McKinley

The first indication of tungsten in the Bishop area was the discovery of scheelite concentrations in a gold placer operation in the ( since named) Tungsten Hills in 1913. After early intermittent production, the deposits of the district were slowly discovered and developed. The Pine Creek mine, located in 1916 and under the direction of Union Carbide Corporation since 1935, became the principal producer in the district. By the end of 1965, the total production of the district had reached 3,450,932 units of WO3, 17,071,242 pounds of molybdenum, and 19,599,110 pounds of copper. The topography of the district is characterized by its extreme relief, ranging in elevation from 13,986 feet to about 4400 feet in the Mount Tom quadrangle. The present topography is the result of the uplift and erosion of the Sierra Nevada and the great subsidence of the Owens Valley with its related deposition and volcanism. The general structure of the pre-Tertiary rocks consists of a series of tightly-folded metasedimentary and metavolcanic rock remnants surrounded by exposed plutons ranging in composition from hornblende gabbro to alaskite. The metasedimentary rocks consist of low- to intermediate-grade metamorphic equivalents of fine-grained sediments deposited during the Paleozoic era in a miogeosynclinal environment. Later volcanics were deposited in a eugeosyncline. The ore bodies in the Bishop district consist of scheelite-bearing tactite formed by the pyrometasomatic replacement* of calcareous sediments along the contact with an acidic granitic intrusive. A number of the metasedimentary remnants have had tungsten deposited along their edges.

Jan 1, 1968

By Lars Rossemyr, Terkel Rosenqvist

The equilibrium Mn + 2 IiCl = MnCl2(g) + H2 has been studied at 1090°C for pure manganese and for Mn-Si alloys. For this reoction a standard free energy of Fo1363, = - 19,700 i 300 col ioas found. Combined with other thermal data, the standard free energy of the reaction Mn(s, ß) + Cl2 = MnCl2(g) was derived: Fo=- 56,140 + 9.78 T log T - 40.10 T For the formation of the various manganese silicides the following free energies were obtained. 5 Mn + 3 Si - M1z5Si3 ?F°1363 = -41,500 i 1500 cal Mn + Si - h.lnSi ?F°1363= -10,000 i 500 cnl Mn + 2 Si = MnSiz ?F°1363= -11,500 ± 500 cal In the search for a method suitable for the study of thermodynamic properties of certain alloy systems, it was found that the heterogeneous equilibrium between the alloy and a gas mixture consisting of hydrogen chloride, hydrogen, and volatile metal chlorides has considerable advantages. In addition to giving thermodynamic information about the alloys, such measurements may be used to derive thermodynamic data for the volatile metal chloride itself. The present paper gives some results which were obtained for manganese silicides and manganous chloride. Similar studies are presently being carried out for the iron silicides. The phase diagram of the Mn-Si system is rather well known,' but no information exists to the authors' knowledge about the thermodynamic properties of manganese silicides or about the chemical activities in molten Mn-Si alloys. At elevated temperature, manganese may react with hydrogen chloride according to the equation: Mn(s, ß ) + 2 HC1 = MnC1, (g ) + H2 [ 1] with the equilibrium constant The value of K, may be determined from measurements of the gas composition in equilibrium with pure manganese. When this value is used in connection with measurements on manganese alloys, the chemical activity of manganese in the alloy may be derived. Initial calculations showed that around 1000" to 1200°C the equilibrium constant K1 has a value of a few thousand, i.e., the reaction is shifted far to the right. In order to study this rather unbalanced gas composition, a flow method was used in two slightly different modifications. For all experiments with manganese silicides and for some experiments with pure manganese the apparatus shown on Fig. 1 was used. A bed of the metal or alloy was placed in a tube furnace. The refractory tube had an internal diameter of 14 mm and the bed was 75 mm long. Electrolytic manganese of high purity and silicon, 99.95 pct Si, were used as raw materials. All alloys were prepared by melting weighed amounts of the elements in a high frequency induction furnace in argon atmosphere. The melting was done in a silica crucible which was placed inside a graphite shell. The alloys were crushed to - 10 +40 mesh and analyzed chemically. Also, for the pure elements, the same size fraction was used. A controlled gas mixture of purified hydrogen and from 3 to 12 pct HC1 was passed through the bed where it reacted with manganese according to Eq. [I]. The volatile manganese chloride was collected in a condenser placed in the cooler part of the furnace tube. The gas mixture before and after the furnace was sampled and analyzed by absorption of

Jan 1, 1962

By Jack Washburn, E. R. Parker

Kinking in zinc single-crystal tension specimens was observed under conditions of low stress and high temperature. Kinking is discussed in relation to other plastic bending phenomena on the basis of dislocation theory. Experiments on the stress-induced motion of small angle boundaries are reported. KINKING was first reported by Orowan1 as a new deformation mechanism. He observed the phenomenon in cadmium single crystals loaded in compression. Glide lamellae in a local region of the rod were observed to snap over suddenly to a tilted position, resulting in a sudden shortening of the specimen. Between the tilted portion and the rest of the crystal there were fairly sharp boundaries, with the slip plane assuming approximately mirror image positions on opposite sides of these boundaries. Orowan considered the boundaries to be regions where dislocations had concentrated. Hess and Barrett' observed the formation of kinks in critically oriented zinc compression specimens. It was found that the sudden snapping over of the tilted region was not an essential part of the kinking phenomenon but rather was associated with the method of loading. Kinking was explained on the basis of the accepted mechanisms of slip and flexural glide. It was also suggested that a kink can be considered as a special type of deformation band. During a recent investigation of the effect of surface condition on creep of zinc single crystals," a similar phenomenon was observed in crystals which were loaded in tension. The specimens were 0.4 in. diam cylindrical rods with a free length of 4 in. between end connections. All of the crystals were tested at a constant load. adjusted to give an extension rate of approximately 0.05 pct per hr. Kinking, as shown in Fig. 1, occurred in some of the tests performed at temperatures above 200°C. Kinking was observed in specimens varying widely in initial orientation, scattering about a 45" angle between the slip plane and the specimen axis. The condition leading to kinking in tension appeared to be non-uniform distribution of flow along the gage length combined with the restraint imposed by the tensile load. At low temperatures and fast strain rates, the distribution of strain throughout the midsection of tension specimens was generally quite uniform; therefore, bend planes developed only near the ends as described by Miller.4 However, at high temperatures under creep conditions it was difficult to obtain specimens in which the distribution of flow was uniform. Some of the factors which may have caused differences in flow stress along the length of the crystals are: Nonuniform distribution of impurities, accidents of growth (lineage structure), slight bending or other damage during handling, surface conditions, and strain-aging characteristics due to dissolved nitrogen." Plastic flow, once started in a local region, often continued to a relatively large strain before other parts of the gage length became active. Under these conditions a series of kinks, such as those in Fig. 1, were produced. Fig. 2 illustrates how a nonuniform distribution of slip produces bending moments which- are responsible for kink formation. If no plastic bending were to occur while the rod extended by pure slip in two separate sections of the rod, it would assume a shape such as that in Fig. 2a. A specimen having this shape and being subjected to a tension load would have concentrations of stress at the concave surfaces C and lower than average stress would exist at the convex surfaces D. Therefore a bending moment is superimposed on the average stress in the regions between C and D. The positions of potential bend planes under these conditions are shown as dotted lines. Actually no such shape as Fig. 2a develops because plastic bending in the region C-D occurs simultaneously with pure slip in the intervening regions. The observed structure of a tension kink is indicated by Fig. 2b. Perhaps the best approach to an understanding of kinking as well as other related plastic bending phenomena, such as the bend planes discussed by Miller,' cell formation studied by Wood et al.,6 and polygonization,7 is consideration of the dislocation model of a bent lattice. Current theories of the slip process postulate generation or multiplication of dislocations at certain lattice imperfections. The mechanism proposed by Frank and Read8 results in continuous generation of concentric dislocation loops which spread out

Jan 1, 1953

By JAMES BRADLEY

THE Spanish mine is in Nevada County, California, 21 miles northeast of Nevada City by road, and 3 miles north of the town of Washington. The mill and surface buildings are on Poorman's Creek at an ele¬vation of 3,000 ft. About 35 men are employed at the property, which is producing 50 tons of ore per day. Electric power, purchased from the Pacific Gas and Electric Co., is brought in from Alleghany, seven miles away. In the early days the mine was operated by F. W. and P. R. Bradley. Between 1883 and 1899 the production was approximately $900,0)0 in gold. The ore treated during; that time yielded an average of 60 cents per ton and was mined and milled at a profit. The surface, oxidized, ore deposit was 30 to 100 ft. wide and was mined by the glory-hole method. The milling-plant at first consisted of a Blake crusher an-1 a small Huntington mill; later three large Huntington mills were added to the plant. In 1893 a new mill was built at a lower adit- It consisted of 10 stamps and four Huntington mills. The gold was secured by amalgamation, the recovery being about 50 per rent.

Jan 1, 1931

By C. A. Crawford

NICKEL and the nickel-copper alloy, the latter generally referred to as morel metal, are available in a variety of wrought and fabricated forums, of which the following are regular commercial products: Form Monel Metal Pure Nickel Roc Hot-rolled; round, hexagon, Same as morel metal square, and flat shapes Cold drawn; round, hexagon, square, and flat shapes Hot-rolled wire rod Cold-drawn wire rod Plates Hot-rolled Same as morel metal Sheets Hot-rolled annealed Same as morel metal Hot-rolled annealed, pickled Full-finished Full-finished, No. 3 grind one side Full-finished, No. 4 grind one side Cold-rolled (annealed) Cold-rolled, No. 5 polished finish Strip Hot-rolled (flat rods) Same as morel metal Cold-rolled (annealed) Cold-rolled (unannealed) Tubes and pipe Gas-welded tube Seamless tube Seamless tube in I. P. S. Gas-welded tube Forgings Bolts, rivets Same as morel metal Nuts and washers Forging to order Castings Sand castings Same as morel metal Centrifugal castings Electrolytic Cathodes of high purity Anodes Cast anodes Rolled anodes Shot and block for 25 to 50-1b. pigs 5, 25 and 50-1b. pigs melting. Shot Shot

Jan 1, 1927

By Arthur F. Taggart

The following conclusions on the work of the Hardinge mill are based on data furnished to the writer by the Hardinge Conical Mill Co. in the form of the mesh cards hereto appended. Energy units (E. U.) and relative mechanical efficiencies (R. M. E.) are computed by the "volume method" of Stadler.' Screen apertures used are the average apertures of testing screeps of the meshes given. i . Card 122. June 28, 1912. Vipond Porcupine Mines Co., Ltd., Schumacher, Ont., Canada. Ore from mill bin. Gangue, quartz and basalt. 4.5 ft. by 13 in. ball mill, Capacity, 48 tons per 24 hr. Charge, 4,000 lb. balls. Speed, 33 rev. per minute. Horsepower, 15 to 17. Water, 100 per cent. by weight. (50 per cent. ?) Product deslimed and oversise reground in pebble mill, see Card 113. Feed to mill through 2-in. mesh. Mesh Feed, Per Cent. Discharge, Per Cent.. + 1in. 5.50 ....... + 3/4. 28.00 + in. 30.00 ...... + 1/4in. 19.72 ....... + 10 10.87 2.10 + 20 2.42 8.00 -20 3.51 .....,. + 40 ....... 22.68 + 60 ...___ 10.50 4-80 ....... 11.80 + 100 ....... 3.90 -100 ....... 40.15

Jan 1, 1916

By H. I. Aaronson, S. M. Kaufman, G. M. Pound

WHETHER the carbides associated with bainite precipitate from the ferritic component of bainite, as originally suggested by Davenport and Bain, or from the adjacent austenite at aus-tenite:ferrite boundaries, as proposed by Hultgren, 2 remains in dispute.3-5 A recent metallographic investigation in this laboratory has shown that the bainitic carbides formed in a plain carbon hypo-eutectoid steel nucleate entirely within ferrite at higher reaction temperatures3 and in both ferrite and austenite at lower temperatures." The present investigation was undertaken to ascertain the effects of alloying elements on the nucleation sites selected by bainitic carbides. The compositions of the steels studied were as shown in Table I. Specimens of these steels were

Jan 1, 1958

By W. L. Doyle

SLAG weights were taken on a series of twenty-eight 6-ton bottom-pour heats. These weights varied from 573 to 1050 lb. Of these, four were chosen for study of the effect of cleaned and uncleaned foundry scrap on the variations of slag weights. Data regarding the make-up and results of the heats are given in Table I. For heat No. 3 the actual slag weight was checked, using the Mn-MnO calculation method-weight 1050 lb. [5,600 X 0.0055 = 30.80 heads and gates 6,000 X 0.004 = 27.00 plate scrap 800 X 0.0083 = 6.64 pig iron 450 X 0.0034 = 1.53 iron ore]

Jan 1, 1947

By Dell P. Williams, Howard G. Nelson

The tensile behavior of magnesium single crystals at a temperature of 26º ± 2ºC was investigated at varying pressure levels from 760 to 8 X 10-8 tow. For crystals deformed at a constant linear strain rate of 0.061 min-1. there was no apparent effect of the vacuum environment down to 10-8 torr. However, from a vacuum of 10-5 torr down to the lowest pressure attained (8 x 10-8 tor,), the effect of the vacuum environment was to increase the strain at the end of the first linear (or easy-glide) stage and to decrease the slope of this stage; the magnitude of this effect was found to be dependent on pressure. The slope of the second linear stage was also decreased at the lower pressure levels; however, this effect appears to be caused primarity by the vacuum effect on the first linear stage. The magnitude of the vacuum-environmrnt effect was also found to be dependent upon strain rate. The reduction in flow stress at 5 x 10-8 torr, as compared to the stress in air, was obserced to be about 10 pct for a strain rate of 0.0250 min-' and 70 pct for a strain rate of 0.67 min-1. No systematic effect of pressure on the critical resolvled shear stress was observed. The data interpreted in terms of a modified form of Mott's work-hardening mechanism for hexagonal metals. It has long been known that surface conditions influence the mechanical behavior of materials. Roscoe 1 demonstrated the importance of surface conditions on mechanical behavior by testing cadmium crystals with oxide layers. He found that the "apparent" critical resolved shear stress for cadmium was increased approximately 2.5 times by the presence of an oxide layer 1000 atoms thick. The magnitude of this effect was dependent on film thickness with crystals having films less than 20 atoms thick still showing a definite increase. This observed strengthening could not be attributed to any strength of the oxide film because of 1) the thinness of the films and 2) an observed increase in the flow stress as deformation proceeded. Harper and cottrel12 obtained similar results on zinc crystals which had been etched and steamed to give artificially thick oxide films. However, in the course of this study, they also carefully examined the very early stages of plastic flow for zinc crystals which in one case had been electrolytically polished and in the other had been lightly etched to produce a thin film. They then found that the critical resolved shear stress for both surface treatments of the crystals was actually identical but that the etched crystal exhibited a much more rapid initial hardening rate. This had not been noted previously. This result indicated that, in fact, the film caused an increase in the stress for continuation of slip, rather than for the initiation of slip. Lipsett and King3 investigated the effect of evaporated gold films on the plastic behavior of cadmium single crystals. For large angles (=75 deg) between the specimen axis and the normal to the slip plane, they found that the stress-strain curve of the coated specimen always lies above that for a clean specimen. The shear strain at the end of the first linear stage was greater in clean specimens than in coated specimens and the slope of the second linear stage was

Jan 1, 1965

By G. M. Ikeda, J. G. Sibakin

An investigation was carried out to determine the variables affecting the coiling temperature of strip in the 56-in. hot strip mill. After statistical treatment, equations have been derived to determine the temperature drop between mill and coiler for both full spray (top and bottom) and top spray only practices. The individual influences of each variable in the temperature drop were derived for both practices. Limitations of the present practices were shown and adjustments in cooling for increased rolling speeds were suggested. A method of estimating the required number of sprays, their spacing, pressure, etc., to achieve a desired temperature drop is developed. MAXIMUM finishing temperature of a hot strip mill is mainly determined by the rolling speed, gage, and the temperature of the bar entering the mill. This finishing temperature may be limited by the maximum admissible coiling temperature in cases when either the cooling facilities on the runout table are not adequate or, more generally, when the cooling capacity of the runout table and the production capacity of the continuous mill are out of balance. Some time ago, the balance between these two factors was not considered detrimental to production. Recently, a new drafting schedule was introduced which increased the production rate, the entry temperature, and hence the finishing temperature. Thus, the restriction of the maximum specified coiling temperature became an important factor for many of the thicker gages. An investigation of the factors determining the coiling temperature may be, therefore, of considerable importance. A brief description of the available equipment will be a useful illustration of the techniques and methods used for this investigation. The 56 in. continuous hot strip mill is composed of six 4-high stands each containing two 221/2-in. diam work rolls and two 45-in. diam back-up rolls. Either of the last two stands can be used as the finishing stand. Which stand is used is dependent on the total percentage of reduction to be taken over the whole train, i.e., on the entry thickness and the final gage. The characteristics of these last two stands are given in Table I. Table I. Operational Characteristics of Nos. 5 and 6 Stands No. .5 NO. 6 Maximum voltage GOO 600 Power, hp 30(10 W00 I normal, kilonmp 4.35 3.73 Rpm of motor and rolls ISO 15 0 ITS to 300 Spettl ot strip, fpm 333 6 to 376T.2 103) to 2062 The speed of the finishing stand varies with the amount of reduction, strip width, and the exit gage. Finishing speeds in general use for varying gages are shown in Table 11. These speeds may change with an increase or decrease in the entry temperature of the strip. Even though the maximum speed of No. 6 stand is shown as 2062 fpm, this has so far never been attained,

Jan 1, 1957

By Michel T. Halbouty

The area for which oil and gas developments in South Texas are reported for 1940 in this paper covers the same counties that were included in the reports for 1938 and 1939, with the addition of LaSalle County. LaSalle County is includcd in the Laredo district of South Texas, which totals seven counties for that district. The Corpus Christi district remains the same, with nine counties. The two districts together comprise what is known as the South Texas area for this report. Continued exploration along established trends and beyond proven field limits during 1940 provided South Texas with new fields and new producing levels at a rate of discovery fairly comparable with the high records set during recent years. The wells drilled in the counties within this district (including LaSalle) numbered 1656, approximately 8 per cent below the 1801 figure of last year. However, rank wildcats totaIed 336, an increase of 17.5 per cent compared to the 286 drilled in 1939. Therefore, since new field discoveries numbered 25 in 1940 against 29 in 1939, the rate of new field discoveries in 1940, based upon rank wildcats drilled, was I/I3.4 while that of 1939 was I/9.86, which shows a decrease of about 25 per cent in the rate of new fields. The rank wildcat tests in 1940 gave the following results: 18 produced oil, 4 produced distillate with gas, 3 produced. only gas, and 3r1 were dry holes (Table 5). Of the 1320 tests drilled in already proven fields or as extensions to pro+en areas (representing a decline of 12.8 per cent from last year's total of 1515 tests), 1048 produced oil or distillate, 60 produced gas and 212 were dry holes (Table 4). Of the producers, 50 found new sands or crude-in-distillate-sands in existing fields. Among the several fields subjected to extensive development were: Colorado, Jim Hogg County; East White Point, San Patricio and Nueces County; Rincon and Sun, Starr County; Glen, Webb and Zapata Counties; Wade City and Orange Grove, Jim Wells County; Stratton and South Clara Driscoll, Nueces County, and Aransas Pass, San Patricio and Aransas Counties. The development of important crude reserves on structures formerly considered primarily distillate fields has probably been the most important phase of the year's operations in South Texas. The Rincon, Stratton, Agua Dulce, Wade City, Odem and Robston fields provided the new crude sand discoveries. At some places crude production was opened by exploratory wells that found new sand horizons; in others by flank wells that found already discovered distillate sands sufficiently low to provide crude production. Rincon, Starr County, with its multiple sands, is now believed to be one of South Texas' largest crude-oil reserves. Offshore drilling showed important results during the year, including the discovery of two new submerged fields and the extension of the East White Point field into offshore Nueces County. The new marine fields are: East Flour Bluff) 76

Jan 1, 1941

By Michel T. Halbouty

The area for which oil and gas developments in South Texas are reported for 1940 in this paper covers the same counties that were included in the reports for 1938 and 1939, with the addition of LaSalle County. LaSalle County is includcd in the Laredo district of South Texas, which totals seven counties for that district. The Corpus Christi district remains the same, with nine counties. The two districts together comprise what is known as the South Texas area for this report. Continued exploration along established trends and beyond proven field limits during 1940 provided South Texas with new fields and new producing levels at a rate of discovery fairly comparable with the high records set during recent years. The wells drilled in the counties within this district (including LaSalle) numbered 1656, approximately 8 per cent below the 1801 figure of last year. However, rank wildcats totaIed 336, an increase of 17.5 per cent compared to the 286 drilled in 1939. Therefore, since new field discoveries numbered 25 in 1940 against 29 in 1939, the rate of new field discoveries in 1940, based upon rank wildcats drilled, was I/I3.4 while that of 1939 was I/9.86, which shows a decrease of about 25 per cent in the rate of new fields. The rank wildcat tests in 1940 gave the following results: 18 produced oil, 4 produced distillate with gas, 3 produced. only gas, and 3r1 were dry holes (Table 5). Of the 1320 tests drilled in already proven fields or as extensions to pro+en areas (representing a decline of 12.8 per cent from last year's total of 1515 tests), 1048 produced oil or distillate, 60 produced gas and 212 were dry holes (Table 4). Of the producers, 50 found new sands or crude-in-distillate-sands in existing fields. Among the several fields subjected to extensive development were: Colorado, Jim Hogg County; East White Point, San Patricio and Nueces County; Rincon and Sun, Starr County; Glen, Webb and Zapata Counties; Wade City and Orange Grove, Jim Wells County; Stratton and South Clara Driscoll, Nueces County, and Aransas Pass, San Patricio and Aransas Counties. The development of important crude reserves on structures formerly considered primarily distillate fields has probably been the most important phase of the year's operations in South Texas. The Rincon, Stratton, Agua Dulce, Wade City, Odem and Robston fields provided the new crude sand discoveries. At some places crude production was opened by exploratory wells that found new sand horizons; in others by flank wells that found already discovered distillate sands sufficiently low to provide crude production. Rincon, Starr County, with its multiple sands, is now believed to be one of South Texas' largest crude-oil reserves. Offshore drilling showed important results during the year, including the discovery of two new submerged fields and the extension of the East White Point field into offshore Nueces County. The new marine fields are: East Flour Bluff) 76

Jan 1, 1941

By E. O. Kirkendall

THE investigation reported herein was undertaken to obtain data to supplement those presented in an earlier paper,' particularly for longer times at a higher temperature. This information may further develop our knowledge of the mechanism of diffusion in substitutional solid solutions. Diffusion of solute atoms interstitially dissolved is not difficult to visualize; it can take place without much disturbance of the solvent atoms. The mechanism of diffusion of solute atoms substitutionally dissolved is not so easily understood. Many theories have been advanced. Rosenhain,2.3 Frenkel,4 Smekal,5 Langmuir,3,6 Steigman, Shockley and Nix,7 and Johnson8 all proposed theories to explain diffusion. Langmuir's proposed mechanism consisted of a simple cyclic interchange of atoms involving an interchange in lattice positions of four or more atoms. This mechanism, accepted by the author at the time of his previous publication,' and apparently quite generally accepted, required a net exchange in positions of both solute and solvent atoms in equal numbers. In other words, the rate of diffusion of the solvent and solute atoms would be the same. That this cyclic interchange in lattice positions of solute and solvent atoms in equal numbers is the only true mechanism of diffusion is denied by the evidence presented in this paper. EXPERIMENTAL PROCEDURE This modification of similar procedure1 will be outlined briefly. The method consisted of the following steps: I. A pure Muntz metal (60.6 per cent Cu, 0.1 per cent total impurities) that was almost all beta brass at 780°C. was chosen. 2. The brass was turned between centers in a lathe to a diameter of 0.5965 inches. 3. After the brass was cleaned, it was electroplated with pure copper to a diameter of about one inch. 4. The sample was heated slowly to 400°C. under reduced pressure and held at that temperature for 4 hr. to remove occluded gases. It was then cooled to room temperature. 5. The sample was heated to 780°C. ±3°C. and held at that temperature for different lengths of time; then quenched. Samples were cut off each time after quenching. Metallographic samples 34 in. thick were removed at I hr., 6 hr., 24 hr., 96 hr. and 701 hr. After 96 and 701 hr. samples of about I in. were removed for X-ray analysis. 6. The metallographic samples were polished on the cross section and photo-micrographs were taken. 7. The I-in. samples were polished and etched on both ends. With the aid of a microscope each was carefully mounted in a four-jaw chuck in a lathe, so that they could be accurately bored for an arbor. 8. Turnings were taken for each X-ray sample. After each set of turnings, the sample was heated in an oil bath for about 3a hr. at 300°C. It was then etched in 25

Jan 1, 1942

By E. O. Kirkendall

The investigation reported herein was undertaken to obtain data to supplement those presented in an earlier paper,l particularly for longer times at a higher temperature. This information may further develop our knowledge of the mechanism of diffusion in substitutional solid solutions. Diffusion of solute atoms interstitially dissolved is not difficult to visualize: it can take place without much disturbance of the solvent atoms. The mechanism of diffusion of solute atoms substitutionally dissolved is not so easily understood. Many theories have been advanced. Rosen-hain,2,3 Frenkel,4 Smekal,5 Langmuir,3,6 Steigman, Shockley and Nix,' and Johnson8 all proposed theories to explain diffusion. Langmuir's proposed mechanism consisted of a simple cyclic interchange of atoms involving an interchange in lattice positions of four or more atoms. This mechanism, accepted by the author at the time of his previous publication,1 and apparently quite generally accepted, required a net exchange in positions of both solute and solvent atoms in equal numbers. In other words, the rate of diffusion of the solvent and solute atoms would be the same. That this cyclic interchange in lattice positions of solute and solvent atoms in equal numbers is the only true mechanism of diffusion is denied by the evidence presented in this paper. Experimental Procedure This modification of similar procedure1 will be outlined briefly. The method consisted of the following steps: I. A pure Muntz metal (60.6 per cent Cu, 0.1 per cent total impurities) that was almost all beta brass at 780°C. was chosen. 2. The brass was turned between centers in a lathe to a diameter of 0.5965 inches. 3. After the brass was cleaned, it was electroplated with pure copper to a diameter of about one inch. 4. The sample was heated slowly to 400°C. under reduced pressure and held at that temperature for 4 hr. to remove occluded gases. It was then cooled to room temperature. 5. The sample was heated to 780°C. ± 3°C. and held at that temperature for different lengths of time; then quenched. Samples were cut off each time after quenching. Metallographic samples 1/4 in. thick were removed at I hr., 6 hr., 24 hr., 96 hr. and 701 hr. After 96 and 701 hr. samples of about I in. were removed for X-ray analysis. 6. The metallographic samples were polished on the cross section and photomicrographs were taken. 7. The I-in. samples were polished and etched on both ends. With the aid of a microscope each was carefully mounted in a four-jaw chuck in a lathe, so that they could be accurately bored for an arbor. 8. Turnings were taken for each X-ray sample. After each set of turnings, the sample was heated in an oil bath for about 1/2 hr. at 300°C. It was then etched in 25

Jan 1, 1942

By E. O. Kirkendall

The investigation reported herein was undertaken to obtain data to supplement those presented in an earlier paper,l particularly for longer times at a higher temperature. This information may further develop our knowledge of the mechanism of diffusion in substitutional solid solutions. Diffusion of solute atoms interstitially dissolved is not difficult to visualize: it can take place without much disturbance of the solvent atoms. The mechanism of diffusion of solute atoms substitutionally dissolved is not so easily understood. Many theories have been advanced. Rosen-hain,2,3 Frenkel,4 Smekal,5 Langmuir,3,6 Steigman, Shockley and Nix,' and Johnson8 all proposed theories to explain diffusion. Langmuir's proposed mechanism consisted of a simple cyclic interchange of atoms involving an interchange in lattice positions of four or more atoms. This mechanism, accepted by the author at the time of his previous publication,1 and apparently quite generally accepted, required a net exchange in positions of both solute and solvent atoms in equal numbers. In other words, the rate of diffusion of the solvent and solute atoms would be the same. That this cyclic interchange in lattice positions of solute and solvent atoms in equal numbers is the only true mechanism of diffusion is denied by the evidence presented in this paper. Experimental Procedure This modification of similar procedure1 will be outlined briefly. The method consisted of the following steps: I. A pure Muntz metal (60.6 per cent Cu, 0.1 per cent total impurities) that was almost all beta brass at 780°C. was chosen. 2. The brass was turned between centers in a lathe to a diameter of 0.5965 inches. 3. After the brass was cleaned, it was electroplated with pure copper to a diameter of about one inch. 4. The sample was heated slowly to 400°C. under reduced pressure and held at that temperature for 4 hr. to remove occluded gases. It was then cooled to room temperature. 5. The sample was heated to 780°C. ± 3°C. and held at that temperature for different lengths of time; then quenched. Samples were cut off each time after quenching. Metallographic samples 1/4 in. thick were removed at I hr., 6 hr., 24 hr., 96 hr. and 701 hr. After 96 and 701 hr. samples of about I in. were removed for X-ray analysis. 6. The metallographic samples were polished on the cross section and photomicrographs were taken. 7. The I-in. samples were polished and etched on both ends. With the aid of a microscope each was carefully mounted in a four-jaw chuck in a lathe, so that they could be accurately bored for an arbor. 8. Turnings were taken for each X-ray sample. After each set of turnings, the sample was heated in an oil bath for about 1/2 hr. at 300°C. It was then etched in 25

Jan 1, 1942

By Samuel S. Wyer

Bethlehem Meeting, February, 1906 THE following abbreviations have been used in the text:¬ Am. MF. and Iron World. American Manufacturer and Iron World, Pittsburg, Pa. Can. Min. Rev. Canadian Mining Review, Ottawa, Can. Cass. Mag. Cassier's Magazine, New York, N. Y. Col. Eng. Colliery Engineer, London, Eng. Col. Guard. Colliery Guardian, London, Eng. Eng. and Min. Jour. Engineering and Mining Journal, New York, N. Y. Eng. News. Engineering News, New York, N. Y. Engr. Engineering, London, Eng. J. I. and S. I. Journal of the Iron and Steel Institute, Lon¬don, Eng. Jour. W Soc. of Engrs. Journal Western Society of Engineers, Chicago, Ill. Lond. Eng. The Engineer, London, Eng. Mines and Min. Mines and Minerals, Scranton, Pa. North of Eng. I. M. E. North of England Institute of Mining Engineers, Newcastle-on-Tyne, England. Oester Zeitsch f. Berg u. Hüt. Oesterrcichische Zeitschrift für Berg. und Hüttenwescn, Vienna, Austria. Pract. Engr. Practical Engineer, London, Eng. Proc. I. C. E. Proceedings Institution of Civil Engineers, London, Eng. Trans. A. I. M. E. Transactions American Institute of Mining Engineers, New York, N. Y. Trans. A. S. M. E. Transactions American Society Mechanical Engineers, New York, N Y Trans. Fed. I. M E. Transactions Federated Institute Mining Engineers, Newcastle-on-Tyne, England. Trans. I M E Transactions Institute Mining Engineers, Newcastle-on-Tyne, England.

Mar 1, 1906

By Larry Dale

An approach for predicting the development of mineral resources on public lands has been developed as an aid to resource agencies. It consists of new techniques for evaluating the economic potential of the resource, the uncertainty about mine cost estimates, and the uncertainty about the occurrance of mineral deposits. New mineral sup- plies from inferred and hypothetical resources can be predicted by using these techniques. A case study illustrates their application in predicting development of copper resources in western Montana.

Jan 1, 1982

By C. H. Mathewson, P.W. Bakararian

The greatcr part of the literature on the plastic behavior of magnesium dates back to that active period of research in crystal mechanics immediately following the widespread preparation of isolated metallic crystals large enough for the application of conventional methods of mechanical testing. These investigations, performed on single crystals, revealed an analogy between zinc and magnesium with respect to their fundamental mode of deformation. in the operation of glide and twinning, respectively, on crystallographically similar planes. Mathewson and Phillips (1928)' by geometrical analysis identified the plane in magnesium as the twinning plane. Schiebold and Siebel (1931) confirmed this twinning planc, established the basal plane as the plane of slip, and a digonal axis I as the slip direction. They also rcported twin formation in a secondary role on the {IOI} plane. Schmid (1931)³ summarized and discussed the earlier evidence and presented the results of his own experiments on the effect of temperature and small amounts of soluble elements. From X-ray studies on extended wire single crystals, he concluded that slip along the basal plane in the direction of the digonal axis I closest to the stress direction was the sole slip system operating at atmospheric temperature. This conclusion was based on experiments with crystals of many different orientations relative to the stress axis. Special attention was directed to the basal plane and the digonal axis I, as the plane and direction of greatest atomic density. Determinations of resolved shear stress at the onset of plastic yielding-—i.e., the critical resolved shear stress—were also made; the average of these calculations showing 82.9 grams per sq. mm. This value varied only slightly up to 300°C. at which temperature it was found to decrease to 70.5 grams per sq. mm. The extension of his crystals at temperatures above 225°C. further disclosed the presence of new slip systems. After the origince specimens of circular section had been

Jan 1, 1943