Search Documents

By A. U. Seybolt, R. A. Oriani

The pressure and composition of the solid solution of nitrogen in chromium has been investigated as a function of temperature. The partial molal heat of solution, the activity of nitrogen in solid solution, and the partial molal free energy have been computed. The enthalpy of three reactions is summarized: N + 2Cr(3) = Cr2N(4), H° = —28,500 cal per mol 1/2N2(p) + 2Cr(8) = Cr2N(3)1 ?HO = —23,500 cal per mol 1/2N2(p) = N, ?H° = 5,000 cal per mol. WORKERS who have investigated the problem of the preparation of ductile chromium have been concerned with the effects of minor amounts of impurities upon this refractory metal. In particular, gaseous impurities such as oxygen and nitrogen have been suspected of causing trouble because of many known cases where brittleness in transition elements has been definitely traced to these elements. In order to evaluate the possible effects of the nitrogen impurity in chromium, it appeared desirable to learn something of the dependence of the nitrogen solubility upon temperature and pressure. Previous Work Maier3 in 1942 in his treatise on sponge chromium reviewed the thermodynamics of the chromium nitrides Cr2N and CrN, both of which are well-estab- lished compounds, but which apparently have not been studied in much detail. Maier presented some free energy-temperature expressions for the reactions 2 Cr,N = 4 Cr + N2 [1] and 4 CrN = 2Cr2N + N2 PI based mainly on the work of Satoh2 and Sano." Pearson and Ende3 in 1953 briefly reviewed the thermodynamics of Cr-N using the same data available to Maier, and also derived a free energy-temperature expression for reaction 1. Of the two nitrides mentioned previously, the present investigation was only concerned with Cr,N, since this nitride is in equilibrium with the metal phase, at least over most of the temperature range, Blix4 in 1929 established the structure of Cr2N (close-packed-hexagonal) by X-ray diffraction methods, and indicated that its homogeneity limits extend from 11.2 pet to 15.1 wt pet N. At a temperature of 1200°C, 38 mm Hg from the Maier expression and 43 mm Hg from the Pearson

Jan 1, 1957

By W. S. Hyler, L. W. Berger, R. I. Jaffee

Hydrogen additions of 390 ppm to A-55 titanium and 368 ppm to Ti-8 pet Mn have no deleterious Hydrogenadditionseffect on the unnotched and notched rotating-beam fatigue properties of these materials. 'These amounts of hydrogen, however, are sufficient to cause severe notch-impact thesematerials.embrittlement in A-55 titanium and pronounced loss of tensile ductility in Ti-8 pet Mn. The lack of embrittling effect in fatigue in the latter alloy is consistent with the postulated strain-aging mechanism of hydrogen embrittlement in a-ß alloys. There is a significant strain-agingincrease in the unnotched endurance limit of A-55 titanium with the addition of hydrogen. This increase may be explained as the result of internal heating effects which would dissolve the hydride and cause solid-solution strengthening. TITANIUM and its alloys may be seriously embrittled by relatively small amounts of hydrogen. The form which this embrittlement takes has been shown to vary with alloy type. The a alloys, for example, suffer most strongly from loss of notch-bend impact toughness' when sufficient hydrogen is added, and this effect has generally been associated with the presence of hydride phase in the micro-structure. In a-ß alloys, on the other hand, hydrogen is most detrimental to tensile ductility in slow-speed tests,2-1 and the embrittlement may be detected in a most convincing manner by means of rupture tests at room temperature. This particular kind of embrittlement has not been associated with a change in microstructure, but has been classified rather generally as associated with a strain-aging type of mechanism.' In the present paper, the effect of an embrittling amount of hydrogen on the rotating-beam fatigue properties of both an a and an a-ß titanium alloy is covered. For this study, annealed commercially pure (A-55) titanium was chosen as an a alloy, and equilibrated and stabilized Ti-8 pet Mn as representative of a typical a-ß alloy. Nominal hydrogen levels of 20 and 400 ppm were evaluated, the latter amount having been shown previously to be severely detrimental to the impact toughness of commercially pure titanium and to cause pronounced strain-aging embrittlement in the Ti-8 pet Mn alloy. The only report of the effect of hydrogen on the fatigue properties of titanium is given by Anderson et al.,° in which a push-pull type of fatigue test was conducted on as-received commercial-purity titanium sheet. Much scatter was found in the results, but generally the presence of hydrides slightly decreased the fatigue strength of unnotched specimens in the longitudinal direction. The results of notched tests were masked too greatly by scatter to be significant. Experimental Procedure Preparation of Materials—Analyses of the A-55 titanium and the Ti-8 pet Mn alloy used in this investigation are given in Table I, which indicates the 8 pet Mn alloy to be more nearly a 6 pet Mn alloy. This alloy will be referred to as Ti-8 pet Mn, however, since this is the commercially designated composition. Both alloys were received in the form of5/8-in. diam rod and, after suitable surface preparation, 5-in. lengths were vacuum annealed at 820°C. Half of the rods for each material were then hydrogenated at 820°C to a nominal hydrogen content of 400 ppm. The hydrogenated and vacuum-annealed A-55 rods were hot swaged at 700°C from 5/8-in. diam to 1/4-in. diam, and then annealed 1 hr at 800°C and air cooled prior to preparation into test specimens. Fabrication of the Ti-8 pet Mn alloy was by hot swaging to 3/8-in. diam at 760" and then 1/4-in. diam at 704°C. This material was then annealed 1 hr at 704", followed by furnace cooling to 593"C, and finally air cooling to room temperature. Evaluation—In order to examine more completely the effects of hydrogen on the particular materials studied, slow-speed tensile and notch-bend impact properties were determined in addition to fatigue data. Tensile specimens were of the standard ASTM type with a reduced section of 1/8-in. diam and a gage length of 1/2 in. A subsize cylindrical Izod specimen was used for impact tests. These specimens had a 45" notch with a 0.005-in. radius and a 0.150-in. root diam, and the stress concentration factor of this notch in bending was Kr = 3. Both the ten-

Jan 1, 1959

By Robert B Sosman

The relative temperature distribution within a coke oven and among the ovens in a battery can be obtained automatically for the operator's guidance by sighting a total-radiation pyrometer on the face of the coke as it is pushed out, and recording the surface temperature. Keeping the instrument clean and keeping its view of the coke unobstructed by smoke and dust are the principal problems. Typical records from three plants are presented in this paper, showing that the temperature patterns are reproducible. Development OF Method The method of coke pyrometry described in this paper was introduced in 1936 by E. A. Lee, then Assistant Superintendent, now Superintendent, of the Coke Plant at Lorain Works, National Tube Co., Lorain, Ohio. At the request of the Coke Committee of the United States Steel Corporation, the Research Laboratory of the Corporation undertook to adapt the method to the somewhat different conditions met with at the Gary Works of the Carnegie-Illinois Steel Corporation, Gary, Ind., and at the Clairton Works of the same Corporation at Clairton, Pa. This work was done in cooperation with the Leeds and Northrup Co. of Philadelphia and later with the Brown Instrument Co. Division of Minneapolis-Honeywell Regulator Co., Philadelphia. We of the Research Laboratory wish to express our appreci- ation of the courtesies extended by Mr. Lee, by A. N. Cole, Superintendent of the Gary coke plant, and by D. P. Finney, Assistant General Superintendent in charge of coke-plant operations at Clairton. We are also indebted to the instrument companies for the loan of a part of the equipment. At Gary and Clairton the instruments were installed and various experiments were made by J. W. Bain, of the Research Laboratory of the United States Steel Corporation. Pyrometry of Coke The coke inside a by-product oven is almost completely inaccessible to pyro-metric instruments. The temperature in the walls can conceivably be measured with thermocouples, but the atmosphere is usually strongly reducing, a condition well known to be destructive to the accuracy of the customary high-temperature couples. In some plants, periodic readings are taken with an optical pyrometer sighted into the top of the combustion flues. This is a useful measure for safety and general control, as it tends to prevent the damage that would result from overheating of the ovens. It does not, however, tell much about the temperature of the coke itself, because of the continually changing gradient in the wall between the coke and the combustion chamber. The best indication of the temperature of the coke itself must therefore be obtained by observation of the product as it is pushed out of the oven. The human eye is very sensitive to variations in brightness of a surface, and particularly to differences in brightness over a continuous hot surface.

Jan 1, 1943

By Robert B. Sosman

The relative temperature distribution within a coke oven and among the ovens in a battery can be obtained automatically for the operator's guidance by sighting a total-radiation pyrometer on the face of the coke as it is pushed out, and recording the surface temperature. Keeping the instrument clean and keeping its view of the coke unobstructed by smoke and dust are the principal problems. Typical records from three plants are presented in this paper, showing that the temperature patterns are reproducible. Development OF Method The method of coke pyrometry described in this paper was introduced in 1936 by E. A. Lee, then Assistant Superintendent, now Superintendent, of the Coke Plant at Lorain Works, National Tube Co., Lorain, Ohio. At the request of the Coke Committee of the United States Steel Corporation, the Research Laboratory of the Corporation undertook to adapt the method to the somewhat different conditions met with at the Gary Works of the Carnegie-Illinois Steel Corporation, Gary, Ind., and at the Clairton Works of the same Corporation at Clairton, Pa. This work was done in cooperation with the Leeds and Northrup Co. of Philadelphia and later with the Brown Instrument Co. Division of Minneapolis-Honeywell Regulator Co., Philadelphia. We of the Research Laboratory wish to express our appreci- ation of the courtesies extended by Mr. Lee, by A. N. Cole, Superintendent of the Gary coke plant, and by D. P. Finney, Assistant General Superintendent in charge of coke-plant operations at Clairton. We are also indebted to the instrument companies for the loan of a part of the equipment. At Gary and Clairton the instruments were installed and various experiments were made by J. W. Bain, of the Research Laboratory of the United States Steel Corporation. Pyrometry of Coke The coke inside a by-product oven is almost completely inaccessible to pyro-metric instruments. The temperature in the walls can conceivably be measured with thermocouples, but the atmosphere is usually strongly reducing, a condition well known to be destructive to the accuracy of the customary high-temperature couples. In some plants, periodic readings are taken with an optical pyrometer sighted into the top of the combustion flues. This is a useful measure for safety and general control, as it tends to prevent the damage that would result from overheating of the ovens. It does not, however, tell much about the temperature of the coke itself, because of the continually changing gradient in the wall between the coke and the combustion chamber. The best indication of the temperature of the coke itself must therefore be obtained by observation of the product as it is pushed out of the oven. The human eye is very sensitive to variations in brightness of a surface, and particularly to differences in brightness over a continuous hot surface.

Jan 1, 1943

On the Art of Metallography (Howe Memorial Lecture), by F. F. Lucas; Beneficiation of Iron Ore. Abstract of paper by C. E. Williams followed by Round Table Discussion; A Statistical Analysis of Blast-furnace Data, by R. 8. McCaffery and R. G. Stephenson; Air Discharge of Circular Tuyeres, by R. S. McCaffery and D. E. Krause; Open-hearth Steel Process as a Problem in Chemical Kinetics. by E. R. Jette; Carbon-oxygen Equilibrium in Liquid Iron, by H. C. Vacher and E. H. Hamilton; A Thermodynamic Study of the Phasial Equilibria in the Bystem Iron-carbon (Abstract), by Yap, Chu-Phay; Influence of Dissolved Carbide on the Equilibria of the System Iron-carbon (Abstract), by Yap, Chu-Phay; Inclusions and Their Effect on Impact Strength of Steel, I and 11, by A. B. Kinzel and W. Crafts: Method for Electrolytic Extraction of MnO, MnS, FeS and Si02, Inclusions from Plain Carbon Steels, by G. R. Fitterer; Permanent Growth of Gray Cast Iron, by W. E. Remmers; Some Notes on Blue Brittleness, by L. R. van Wert; Austenite-pearlite Transformation and the Transition Constituents, by A. Sauveur; Age-hardening of Austenite, by F. R. Hensel; Transformational Characteristics of Iron-manganese Alloys, by H. Scott; Composition Limits of the Alpha-gamma Loop in the Iron-tungsten System, by W. P. Sykes; Magnetic Properties Versus AUotropic Transformations of Iron Alloys, by T. D. Yensen and N. A. Ziegler; Dilatometric Study of Chrome-nickel-iron Alloys, by V. N. Krivobok and M. Gensamer; Low-carbon Steel, by H. B. Pulsifer; Bright Annealing of Steels in Hydrogen, by F. C. KeUey; Development of Continuous Gas Carburieing, by R. J. Cowan. Transactions, Institute of Metals Division, 1931. 500 pages. Index. Papers and discussions presented before the Division at Chicago, Sept. 22-26, 1930 and New York, Feb. 16-19, 1931. X-ray MetallograpIhy: X-ray Determination of Alloy Equilibrium Diagrams (Annual Lecture), by A. F. Westgren; Suppressed Constitutional Changes in Alloys. by G. Sachs; Texture of Metals after Cold Deformation; by F. Wever. Theoretical Metallurgy: Studies upon the Widmanatitten Structure. I.—Introduction. The Aluminum-eilver System and the Copper-silicon System; by R. F. Mehl and C. S. Barrett; Studies upon the Widmanstatten Structure, 11.—The Beta Copper-einc Alloys and the Beta Copper-alumnum Alloys, by R. F. Mehl and 0. T. Mareke; Application of X-rays in the Manufacture of Telephone Apparatus, by M. Baeyerts; Thermal Conductivity of Copper Alloys. 11.—Copper-tin Alloys; 111.—Copper-phosphorus Alloys, by Cyril Stanley Smith; Thermodynamic Study of the Equilibria of the Systems Antimony-bismuth and Antimony-lead, by Yap, Chu-Phay. Ganeral: Cemented Tungsten Carbide; a Study of the Action of the Cementing Material, by L. L. Wyman and F. C. Kelley; Influence of Casting Practice on Physical Properties of Die Castings, by C. Pack; Fabrication of the Platinum Metals, by C. S. Sivil; Effect of Certain Alloying Elements on Structure and Hardness of Aluminum Bronze, by 9. F. Hermann and F. T. Sisco. The WorkinG oF Metals: Metal Working in Power Presses, by E. V. Crane; Forming Properties of Thin Sheets of Some Nonferrous Metals, by W. A. Straw, M. D. Helfrick and C. R. Fischrupp; Die Pressing of Braas and Copper Alloys, by J. R. Freeman. Jr.; Plasticity of Copper-sina Alloys at Elevated Temperatures. by A. Morris: Directional Properties in Cold-rolled and Annealed Copper, by A. Phillips and E. 9. Bunn; Effect of Combinations of Strain and Heat Treatment on Properties of Some Age-hardening Copper Alloys by W. C. Ellis and E. E. Schumacher; Constituents of Aluminum-iron-silicon Alloys, by W, L. Fink and K. R. Van Horn; Equilibrium Relations in Aluminum-antimony Alloys of High Purity, by E. H. Dix, Jr., F. KeUer and L. A. Willey; Equilibrium Relations in Aluminum-magnesium Silicide Alloys of High Purity, by E. H. Dix. Jr., F. Keller and R. W. Graham; Constitution of High-purity Aluminum-titanium Alloys, by W. L. Fink, K. R. Van Horn and P. M. Budge; Experiments on Retarding the Age-hardening of Duralumin, by E. H. Dix. Jr. and F. KeUer; Aluminum-silicon-magnesium Casting Alloys, by R. S. Archer and L. W. Kempf; Modulurr of Elasticity of Aluminum Alloys, by R. L. Templin and D. A. Paul; Quenching of Alclad Sheet in Oil, by H. C. Knerr.

Jan 1, 1931

By Robert Glass Cleland

THE MEMBERS of the Phelps-Dodge, Phelps-James co- partnership differed widely from one another in certain aspects of temperament and personality; but in one thing Anson Phelps, William Dodge, and Daniel James were fundamentally alike. They were all bred in the English Puritan tradition. Their creed, moreover, was the stern, militant, uncompromising creed of John Calvin and John Knox. The present generation, harshly intolerant of such a creed, has little understanding of the authority it exercised on the thinking and conduct of its adherents or of the contributions that those same adherents made to human welfare and social progress. The men who accepted its authority "were characterized by a blend of strong individualism and an equally strong sense of social duty, and they submitted their own souls to the same searching scrutiny that they applied to their business ledgers." To all three of the immediate founders of Phelps Dodge, their religion was the most real and important thing in life. It was with them day and night, in joy and sorrow, in loss and prosperity, in their most trivial personal affairs, in business transactions of the greatest moment. It was with

Jan 1, 1952

Abadilla, Quirico A. Catanawan, Tayabas, P I '20 Abbey, Robert Graham, District Mgr., The W. W. Sly Mfg. Co, 50 Church St, New York, N. Y. '21 Abbott,-A. N., Mines Supt, Mazapil Copper Co., Ltd .. Concepcion del Oro, Zac., Mexico. '23 Abbott, Clarence E., Mgr, Mines & Quarries, Tenn. Coal, Iron & R R Co. 1242 Brown Marx Bldg, Birmingham, Ala. '04 Abbott, Louis Benjamin, Chief Engr, Consolidation Coal Co, Elkhorn Div . Jenkins, Ky. '15 Abeel, George H., Jr., Cons Min Engr... . Box 427, Santa Monica, Cal. '18 Abel, Albert E., Asst. to Pres., Valley Mould & Iron Corp Hubbard, Ohio. '19 Abel, Raymond L., Asst. Prof., Dept. of Pet. Refin , Univ. of Pittsburgh Pittsburgh, Pa. '28 Abernathy, George Elmer, Prof. of Geol. & Min., Kansas State Teachers College. Pittsburg, Kans '20 ||Abernethy, D. Carl, Jr. Min. Engr., Hudson Coal Co . Scranton, Pa '27 Abey, Hiroshi, Min. & Met. Engr., Min. & Met. Dept, The Higher Technical School, Osaka, Japan. '17 Aborn, Robert H., Instructor in Met, Harvard University Cambridge, Mass. '19 Abozeid, Mahmood, Pet. Production Engr., Marland Oil Co Ponca City, Okla. '20 Abraham, Arthur W., Geol, Richfield Oil Co. Box 788, Bakeisfield, Cal. '20 Abraham, W. E. V., Member, Geol Staff of Burmah Oil Co, Ltd Nyaunghla. Upper Burma, India. '23

Jan 1, 1923

By Robert T. Howard, Morris Cohen

IT has long been realized among metallurgists that a fast, reliable method for the quantitative determination of the percentage of microconstituents in an alloy would be of great benefit in studies of equilibrium and transformation in the solid state. For example, Polushkin1 has shown that the compositions of two coexisting phases in a a binary system at a given temperature may be calculated very simply with the aid of two alloys lying in the two-phase field if the relative amounts of the two phases in each alloy can be determined. Recently, Grange and Stewart2 have traced the course of the austenite-martensite reaction in a series of commercial steels by making visual estimates of the percentage of martensite formed as a function of cooling temperature. The correlation of mechanical properties with structure, a subject of wide-spread current interest, is likewise dependent upon quantitative microanalysis.3 Yet, there are very few investigations described in the metallurgical literature, wherein methods of quantitative microscopy are employed. Usually, the relative amounts of the microconstituents are estimated in a qualitative or semiquantitative way. The authors were faced with this problem some time ago in studying the kinetics of austenite decomposition. Several aspects of, this research could not be treated satisfactorily by other quantitative tools, such as specific volume,4 magnetic,5 dilatometric,6 electrical resistance7 or x-ray measurements.8 It became necessary to find an impersonal quantitative method that could be applied to microstructures. Fortunately, it was noted that geologists and petrographers had coped with quantitative microscopy to a considerable degree in their attempts to evaluate the mineral contents of rocks. A number of excellent articles were found on this subject, and since they appear to be unknown generally to many metallurgists, the first part of the present paper is concerned with a review of the literature in some detail. With this survey as a background, the authors have adapted the so-called methods of point-counting and lineal analysis to metallography, as described in the second part of the paper. Austenite-martensite structures were selected for illustration not only because they are important in many ways, but because such fine intermixtures are notoriously difficult to estimate visually. LITERATURE SURVEY Perhaps the earliest work on quantitative microscopic analysis goes back to Delesse9 (1848) who proved mathemati-

Jan 1, 1947

By C. E. Lesher

THE Disco* process for the production of low temperature coke and its immediate predecessor, the Wisner or Carbocite process have been described in the voluminous literature of low temperature carbonization.1 This paper will describe the development of the process from the first attempt at commercial operation by the American Gas and Electric Co. at Philo, Ohio, Yn the 1920's to the successful operation in 1949 by the Disco Co., a division of the Pittsburgh Consolidation Coal Co., of the 1000-ton per day Disco plant near Pittsburgh, see Figs. 1-2. In the 1924 coal industry depression following the hectic post World War I expansion, the northern Appalachian, unionized bituminous coal fields were affected first and foremost, and Western Pennsylvania as hard as any. Competitive market pressure was heaviest on the lower grades of steam coals, notably the from the Panhandle district where ash and sulphur are inherently higher than in the same Pittsburgh coal bed to the east along the rivers. The firm structure of Panhandle coal while favoring the prepared sizes, depressed the usefulness and value of the finer sizes. Panhandle slack and nut slack were marketed with difficulty at consistent, and at times considerable, loss. Many solutions were suggested, and the Pittsburgh Coal Co. investigated all. Lower delivered prices through lower mine costs and more advantageous freight rates were obvious goals, but equally obvious were the difficulties of self attainment of either in any substantial measure. Selling Btu's in pipes was abandoned as an idea after a thorough study of the economics of distribution of what was then, and is even now, the only developed continuous process of complete gasification of bituminous coal-producer gas. Although the coal company purchased huge blocks of electric power, it sold not a car of coal to the central power stations. Public utilities controlled the markets for electric current, and it was found that no matter at how low a cost current might be put on the bus bars by the coal company, distribution to its widely scattered coal mines made such an enterprise practically impossible. Consolidation of underground operations and a huge modernization program of mining operations in the 1920's were but preparation for the introduction of mechanical cleaning of the coal for market, particularly the smaller sizes of steam, gas, and by-

Jan 1, 1953

By C. E. Lesher

THE Disco* process for the production of low temperature coke and its immediate predecessor, the Wisner or Carbocite process have been described in the voluminous literature of low temperature carbonization.1 This paper will describe the development of the process from the first attempt at commercial operation by the American Gas and Electric Co. at Philo, Ohio, Yn the 1920's to the successful operation in 1949 by the Disco Co., a division of the Pittsburgh Consolidation Coal Co., of the 1000-ton per day Disco plant near Pittsburgh, see Figs. 1-2. In the 1924 coal industry depression following the hectic post World War I expansion, the northern Appalachian, unionized bituminous coal fields were affected first and foremost, and Western Pennsylvania as hard as any. Competitive market pressure was heaviest on the lower grades of steam coals, notably the from the Panhandle district where ash and sulphur are inherently higher than in the same Pittsburgh coal bed to the east along the rivers. The firm structure of Panhandle coal while favoring the prepared sizes, depressed the usefulness and value of the finer sizes. Panhandle slack and nut slack were marketed with difficulty at consistent, and at times considerable, loss. Many solutions were suggested, and the Pittsburgh Coal Co. investigated all. Lower delivered prices through lower mine costs and more advantageous freight rates were obvious goals, but equally obvious were the difficulties of self attainment of either in any substantial measure. Selling Btu's in pipes was abandoned as an idea after a thorough study of the economics of distribution of what was then, and is even now, the only developed continuous process of complete gasification of bituminous coal-producer gas. Although the coal company purchased huge blocks of electric power, it sold not a car of coal to the central power stations. Public utilities controlled the markets for electric current, and it was found that no matter at how low a cost current might be put on the bus bars by the coal company, distribution to its widely scattered coal mines made such an enterprise practically impossible. Consolidation of underground operations and a huge modernization program of mining operations in the 1920's were but preparation for the introduction of mechanical cleaning of the coal for market, particularly the smaller sizes of steam, gas, and by-

Jan 1, 1953

By W. L. III McMorris, R. E. Zimmerman, Michael Sokaski, E. R. Palowitch, M. R. Geer, C. E. Capes, A. W. Deurbrouck, S. C. Sun

PART 1: DENSE MEDIUM SEPARATION by M. SOKASKI, M. R. GEER, and W. L. MCMORRIS III INTRODUCTION In the early days of coarse-coal treatment by the dense-medium process in Europe, loess was one of the materials used for medium solids. Newly developed cyclones were used to reclaim and thicken the loess suspension. On occasion, when the cyclone thickener at the Maurits mine in the Nether- lands plugged, the overflow was found to be filled with clean coal free of impurity. From this observation stemmed the concept of the cyclone as a cleaning device. Development took place during World War I1 in the lab- oratory of the Dutch State Mines under the direction of M. G. Driessen. A 15 tph (13.6 mt) pilot plant was in operation in the laboratory by 1945, when, in September, Driessen made the first public disclosure of the process in a paper presented to the Institute of fie1 in London. In April 1945 operation of this pilot plant was observed by H. F. Yancey, who was so

Jan 1, 1979

By Charles B. Dudley

THEO. N. ELY, Esq., Superintendent of Motive Power. DEAR SIR: It is now nearly three years since my first report to you on the subject of steel rails was written. That report, as you will remember, dealt principally with the question of the relation between the chemical composition and physical properties of steel rails and their power to resist crushing and fracture in actual service. Other matters were referred to or touched upon in that report, but the main question was, Why do some rails crush or break in service while others do not? You will doubtless remember that the principal conclusion arrived at was, that the softer rails are less liable to crush or break in service than the hard ones. Or, in other words, so far as conclusions could be drawn from the chemical analysis and physical test of 25 samples of steel rails which had actually been in service, these conclusions were that those rails which have the smaller amounts of carbon, phosphorus, silicon, and manganese are less liable to crush or break in service than those which have larger amounts of these elements. Or, again, looked at in the light * At the Lake George meeting of the Institute in October, 1878, I had the honor of presenting to the Institute, through the kind permission of the officers of. the Pennsylvania Railroad Company, the results of a study of twenty-five samples of steel rails, which had all been in actual service. Considerable discussion followed the publication of that paper, and there seemed to be a strong disinclination, especially on the part of the steel-rail manufacturers, to accept the conclusions presented. One of the principal objections urged against the conclusions drawn was, that they were based on too few samples; in other words, that no conclusions safe to act upon could be drawn from the examination of twenty-five rails. In view of this criticism it was decided to repeat the investigation with a larger number of samples, and with the aid of the experience gained in the first investigation. The results of this second study of steel rails are, by the permission of the officers of 'the Pennsylvania. Railroad Company, herewith presented to the Institute, with the sincere desire that they may aid in adding to our knowledge of this most important product. Like the previous paper, this is in the form of a report to one of the officers of the company, which will account for the style, and the manner of presenting the data

Jan 1, 1881

Thirty years ago a party of American Engineers, with members of their families, belonging to the four national engineering societies, sailed for Europe and visited England and the Paris Exposition of 1889 and received many courtesies, official, professional, and individual. Plans: have been made for a reunion dinner to be held in New York City, about May 26, at which it is hoped that all survivors, ladies as well as men, of that trip may meet again. It is, therefore, urgently requested that anyone who was of that party communicate immediately with the Secretary of the Committee, Jesse M. Smith, Engineers' Club, 32 West 40th St., New York, N. Y. Announcement of the precise date and place, and full details, will he sent to every individual who can he reached.

Jan 5, 1919

By John V. Beall

Early this year at the University of Arizona in Tucson, a survey was made of student opinion about the minerals industry. Over 100 of the three page questionnaires were completed and these were analyzed by the following categories: 40 Mining Engineering students, 20 Geological Engineering with 2 Geophysical Engineering students, 15 Geology students, 7 Metallurgical Engineering, 26 Underclassmen, 29 Graduate students and a composite of 84 total students. Not all of the results of the survey were predictable. After graduation there is a strong preference toward going to work in the mineral industries. The next most popular options, but trailing the first choice greatly, was graduate work or employment in another industry. A smattering of other choices were for teaching, government or research. None checked the box for drop out.

Jan 1, 1971

By James D. Reilly

13.1-1. Introduction. COAL RESERVES OF THE UNITED STATES. Bituminous coal is the most abundant fossil fuel in America. With reserves of 1,660 billion tons and assumed recovery of 5070, there is more than 830 billion tons of recoverable coal--enough to assure ample supplies of energy for centuries. Looking at Fig. 13.1-1, coal is found in a majority of the states, including [ ]

Jan 1, 1968

By P. F. McIntyre

Electrolytic refining of lead was first carried out on a commercial scale at Trail, B. C., in 1903. The capacity at that time was small, and cell-changing operations were managed with chain block and monorail. Development up to 1922, utilizing crane installations and cell additions, attained a production of 100 tons per day. Successive additions from 1922 to 1926 further increased the rated capacity to 396 tons per day. Other improvements in metallurgical practice have gradually increased production, until for the year 1935 it was 448 tons per day. During the first five months of 1936, an average daily production of 504 tons was maintained without increasing the size of the plant. Lead Refinery Buildings.—The tank room and the lead-melting and casting equipment are housed in two buildings, which parallel each other and which for the greater part of their lengths are joined by a connecting aisle. All basements, walls, sumps and floors are of concrete. Where exposed to the electrolyte, the concrete has a protective coating of asphalt (220" melting point) over a coat of asphalt paint as a primer. Buildings erected before 1924 are of wood. More recent additions are made of structural steel with gunite siding. A brick building, adjoining the older section of the tank room, houses the slimes-treatment plant. The power house, containing motor generators, air compressors and rectifiers, is constructed of tile. Cell Construction.—The electrolytic cells are of reinforced concrete lined with asphalt. They are cast in pairs, the outside dimensions of a double cell being 113 in. long by 73 in. wide by 48 in. deep. The bottom is 6 in. thick and the sides, ends and center wall are 4 in. thick. A ledge 3 in. wide and 2½ in. deep is left along the top of the side walls to carry the insulators and bus bars. Reinforcing consists of ½-in. round iron rods. Cell inspection and repair work is done in conjunction with the cell-changing operations. The repair work necessary is usually confined to renewing chipped asphalt, unless a tank has been accidentally broken. Minor concrete repairs can be easily made in place. The broken concrete

Jan 1, 1937

By Robert S. Dewey

More wells were drilled in West Texas† during 1944 than in any year since 1941. As compared with 1943, there was an 82.5 per cent increase in the total number of completed wells. The 1646 wells required an estimated 140,715 days to complete for a total of 7,632,249 ft. An average of 85 completion days was required to drill to an average of 4630 ft. This depth is approximately 100 ft. greater than that of the previous year. It is estimated that $100,000,000 was invested in drilled wells. As of Dec. 31, 1944, there were 270 field and 91 wildcat wells being drilled. While an identical number of wells were drilling Dec. 31, 1943, the proportion of wildcats increased in 1944 from 19.7 to 25.2 per cent. During 1944, oil wells were completed in 103 of the 164 fields in West Texas. Of the 1361 oil wells, 385 were in Slaughter, 116 in Fullerton, 63 in North Cowden, 62 in Fuhrman-Mascho, 59 in Wasson, 52 in Westbrook and 47 in North Ward. Approximately 22 per cent of the wildcat drilling was to pre-Permian formations. Despite the increasing proportion of wildcat wells drilled, the wildcat discovery rate has declined since the year 1942. AS compared with 1943, the number of wildcat wells drilled increased from 11.7 to 12.7 per cent and the footage in wildcat exploration increased from 13.3 to 13.8 per cent of the total. The monthly production of crude continued to increase to a peak of 15,336,000 bbl. in October 1944. As compared with a similar peak production in October 1943, there was a 37.3 per cent increase. The yearly production increased from 98,165,-ooo bbl. in 1943 to 159,943,000 bbl. in 1944, an increase of 62.8 per cent. Based upon an assumed average price of $1.00 per barrel and less 1/8 royalty, the gross return to the producer amounts to $140, 000,000. From 1943 to 1944, the average number of producing wells increased 6 per cent while the average daily production per well increased 53.1 per cent. The average daily production per well increased from 17.5 bbl. in 1943 to 26.8 bbl. in 1944. The proportion of flowing wells decreased from 50.5 per cent in January to 49.1 per cent in December 1944. Drilling With the continued shortage of labor and materials, drilling costs have risen sharply. Just how much is difficult to ascertain. Owing to competition for available drilling rigs, contractors are reluctant to assume drilling risks. In consequence, some contracts are let on a cost plus basis, or day work below some specified depth with the operator furnishing part of the consumable materials, such as mud and drilling bits. Contractors are having difficulty in maintaining full and effective drilling crews with insufficient and inexperienced labor. Service companies have inadequate labor and equipment to meet their appointments promptly. Pipe Lines The Gulf Pipe Line Co. increased the capacity of its 10-in. main line by filling in gaps amounting to 75 miles on the loops between Judkins and Weatherford, Texas.

Jan 1, 1945

By C. C. Griggs

FROM its inception, a limestone quarry or mine should be under the direction of a capable engineer. Before it becomes a reality, he should outline the future results, plan the most economical methods for moving the materials and the most efficient equipment, and pilot the undertaking along the narrow pathway of success, avoiding the pitfalls of uneconomical production and the precipitous walls of scanty profits. Inspection of successful limestone properties shows that all have had difficult engineering problems, the solution of which have required keen engineering ability. In approaching a subject of this nature, it is logical to follow the progress of the limestone operation from its inception to the end, as reflecting the engineering required. There are four major divisions: Investigation, equipment, development, and operation.

Jan 2, 1925

By A. H. Geisler, R. F. Mehl, S. Barrett

The studies of the mechanism of pre= cipitation and of the resulting property changes in aluminum-silver alloysl-3 have presented some new concepts of the aging reactioxl—concepts that may be fundamental in establishing a complete quantitative theory of age-hardening. With both aluminum-copper and aluminum-silver alloys, thin platelike aggregates form parallel to the Widmanstätten planes of precipitation.l,4 These platelets grow in lateral dimensions and in thickness with aging time until they arc thick enough to produce an X-ray diffraction line pattern. Their structure is that of a transition lattice which is coherent with the matrix, since the atomic spacings in the matrix and the precipitate are the same on each side of their common interface.2,4 The equilibrium precipitate forms later from and at the expense of the transition lattice. Since age-hardening occurs during the formation and growth of the transition lattice, the major contributor to the hardening no doubt is the stress condition in the matrix resulting from the matrix holding the precipitate in the coherent condition. The development of these stresses also appears to be responsible for an increase in the electrical resistance superimposed on the normal decrease resulting from a change in the concentration of the matrix during aging.3 The two consecutive reactions constituting the aging process are accompanied by characteristic microstructural alterations. The initial precipitation process results in the formation of a Widmanstatten figure, while the later transformation of the transition lattice to the equilibrium lattice is accompanied by a coalescence, in the case of aluminum-copper alloys,5 and by the appearance of light areas at the grain boundaries with aluminum-silver alloys showing a structural rearrangement of matrix and precipitate.3 This latter reaction is similar microscopically to the so-called "discontinuoils precipitation." Possibly discontinuous precipitation is a process that often if not always follows true precipitation of a coherent lattice and during which the transformation of the coherent transition lattice to the equilibrium lattice takes place accompanied by matrix recrystallization.3 Expermental Procedure The alloys were made using 99.97 per cent A1 or distilled magnesium, with

Jan 1, 1943

By R. F. Mehl, A. H. Geisler, S. Barrett

The studies of the mechanism of pre= cipitation and of the resulting property changes in aluminum-silver alloysl-3 have presented some new concepts of the aging reactioxl—concepts that may be fundamental in establishing a complete quantitative theory of age-hardening. With both aluminum-copper and aluminum-silver alloys, thin platelike aggregates form parallel to the Widmanstätten planes of precipitation.l,4 These platelets grow in lateral dimensions and in thickness with aging time until they arc thick enough to produce an X-ray diffraction line pattern. Their structure is that of a transition lattice which is coherent with the matrix, since the atomic spacings in the matrix and the precipitate are the same on each side of their common interface.2,4 The equilibrium precipitate forms later from and at the expense of the transition lattice. Since age-hardening occurs during the formation and growth of the transition lattice, the major contributor to the hardening no doubt is the stress condition in the matrix resulting from the matrix holding the precipitate in the coherent condition. The development of these stresses also appears to be responsible for an increase in the electrical resistance superimposed on the normal decrease resulting from a change in the concentration of the matrix during aging.3 The two consecutive reactions constituting the aging process are accompanied by characteristic microstructural alterations. The initial precipitation process results in the formation of a Widmanstatten figure, while the later transformation of the transition lattice to the equilibrium lattice is accompanied by a coalescence, in the case of aluminum-copper alloys,5 and by the appearance of light areas at the grain boundaries with aluminum-silver alloys showing a structural rearrangement of matrix and precipitate.3 This latter reaction is similar microscopically to the so-called "discontinuoils precipitation." Possibly discontinuous precipitation is a process that often if not always follows true precipitation of a coherent lattice and during which the transformation of the coherent transition lattice to the equilibrium lattice takes place accompanied by matrix recrystallization.3 Expermental Procedure The alloys were made using 99.97 per cent A1 or distilled magnesium, with

Jan 1, 1943