Search Documents

By H. W. Clark

Electricity must be safeguarded everywhere that it is used. The conditions that exist underground make the use of safeguards more essential there than almost anywhere else. Electric Shock Electric shock is the greatest danger in connection with the use of electricity in mines, because conditions existing underground are so favorable to its occurrence. Men are often obliged to work in more or less uncertain light near bare wires that are carrying dangerous potentials. The fact that the men are standing on the earth practically connects them to one terminal of the electric generator. The moat dangerous piece of electrical equipment underground is the trolley wire. It is necessarily bare and extends for long distances throughout a mine, often less than a man's height from the track rail. Sometimes the making up of trips of cars must be done near low-hanging trolley wires. All 'bare wires offer the same danger that troIley wires do, although not to the same extent. Apparatus that has accidentally come in contact with the ungrounded side of an electric circuit is almost as dangerous as the trolley wire. A severe and even fatal shock may be obtained by coming in contact with the frame of a motor or a switch box that has become charged with electricity, or "alive," as it is usually termed. It is also possible to obtain . shocks from the frames of locomotives and cars if track sanding, poor bonding or a similar cause has put a high resistance to earth in the path of the current. Fires Caused by Electricity The danger from fires caused by electricity arises principally from defective installation and careless upkeep or from injuries to equipment resulting from falls of roof or similar causes. Fires may be started by unrelieved short cifiuits, or grounds, by the blowing of open fuses, and by the overheating of resistances. Incandescent lamps can produce heat enough to ignite combustible materials if the dissipation of the heat from

Jan 1, 1915

Silver ore was first discovered in 1866 at Manhattan, and a few ore shipments were treated in a mill at nearby Belmont. The district was abandoned from 1869 to April 1, 1905, when rich gold float was discovered on what was to be called the April Fool claim. By early 1906, 4, 000 people lived in Manhattan. The San Francisco earthquake, in April of 1906, caused the withdrawal of capital from Manhattan and most of the mines were shut down. Later that year and in 1907, however, more strikes were made. The camp prospered until the mid-1920s, but a steady production of several hundred thousand dollars per year was sustained even during the great depression. Then, in 1939, Nevada's first bucket-line dredge was installed below the town and operated until 1947, producing $4.6 million in gold. The Houston International Minerals operation at Manhattan was started in July of 1980 at a throughput of about 545 mt per day (600 st per day). In contrast to the early day underground operations, Houston's mine is open-pit and processes low-grade disseminated ores. The ore is a metamorphic schist containing 2. 7 g Au and 1. 03 g Ag per mt (0. 08 oz Au and 0. 03 oz Ag per st). Some coarse gold, up to 1 mm in size, is present. Mining and haulage is done by a contractor. Stockpiled mine-run ore is crushed in three stages comprising a jaw crusher and two cone crushers, with screens ahead of the cone crushers. Crushed product, at about 19 mm (3/4 in.) size, is stored in a silo. Grinding is by single stage ball mill with the discharge passing over two hydraulic traps for coarse gold removal. These traps will be replaced in late 1980 by a two-cell Pan American jig treating the cyclone underflow. The jig hutch product, along with the hydraulic trap product that has been stored, will be treated further for gold recovery. The gravity tails will then be cycloned with the underflow being recirculated in the ball mill and the overflow being treated by flotation. A rougher concentrate is made in twelve No. 48 Galigher cells with the float tails being cycloned. Cyclone underflow is refloated in another four No. 48 cells; the overflow is treated in sluice boxes for further gold recovery before being sent by gravity to the tailings pond. Bulk flotation concentrates are cleaned three times with the final concentrate being thickened. The thickener underflow is then batch cyanided in mechanically agitated tanks and washed with barren liquor

Jan 1, 1981

INTRODUCTION TO SAMPLING THEORY Before specifically discussing mineral sampling and sampling procedures, let us briefly consider broader and more universal concepts of modem sampling theory. A sample is de- fined as a representative part or a single item from a larger whole, being drawn for purpose of inspection or shown as evidence of quality. In modem theory the sample is a part of a statistical population whose properties are studied to gain information about the whole. The theory of sampling is built around the concept that if enough representative units of a larger overall population are selected without bias, the average value of the units will approximate that of the total population. Modem theory attempts to answer the question of how many samples are enough, given certain limits and constraints, and seeks to apply methods of sample selection and of estimation that provide, at the lowest possible cost, estimates that are precise enough for the purposes at issue. In order to meet these objectives the designer of a sample survey must rely heavily upon statistical theory. Statistics has been defined as the collection, presentation, analysis, and interpretation of numerical data. Statistical methods are primarily concerned with making valid inferences about a population based upon samples taken from the population. For most statistical applications, the total sample is in terms of number of items, attributes, or things; whereas mineral samples are usually in terms of weight or volume of mineral particles. Certain steps are involved in a well designed sample survey without regard to the particular field of application. Because the desired characteristics of an unmined mineral deposit can- not be known other than by sampling, we will consider these principle steps in terms of a mineral sample survey: 1) Clear definition of the objectives of the survey. In the case of mineral sampling this step is so apparent as to be almost ridiculous. However, it is surprising how often the overall objective of a sampling program is overlooked when decisions are made on a day-today basis. 2) Definition of the population to be sampled. The word population is used to designate the aggregate from which the sample is chosen. A sampling program may be designed to determine the grade of a single stope within a mine, the grade of a particular zone within a complex ore body, or the total value and extent of a mineral deposit. Since mineral sampling is usually done in phases, it is well to

Jan 1, 1980

By Tormod Forland

FROM equilibrium measurements on the system NaF-Na 3A l Fo-A 1 2 O 3-Na CO 3-CO 2 with high contents of NaF, Forland, Storegraven, and Urnesl concluded that complexes are formed containing two oxygen, three aluminum, and a less defined number of fluorine per complex. The same number of oxygen atoms per complex was also found by cryoscopic measurements for mixtures high in NaALF 6. In a recent paper by Stokes: some other complex ions, Al2O2F42- and AlOF2-, have been suggested. Here an additional argument in favor of the complex ALO2F. suggested by Forland, Storegraven, and Urnes will be given. When fused Na3AlF6 containing some A12O3, is cooled slowly, the solid phase will consist of the two components as separate phases. The melting point and the heat of fusion of Al2O3 are so high that this component will form the stable solid phase even though in the liquid state the complex may have a high stability. If, however, the fused mixture is quenched, the decomposition of the oxygen-containing complex and the formation of solid Al2O3 does not proceed fast enough, and a solid solution of A12O3 in Na3AlF6 is obtained. Zintel and Morawietz3 obtained cryolite containing 10 pct AL2O3 in this way. The density and the lattice parameters of the A12O3 containing cryolite were also measured, and from this it was concluded that the Al2O3 enters the cryolite lattice as Al3AlO0 groups replacing Na3AlF6 groups. However, the experimental data could as well be explained by assuming that one Na+ ion and two of its neighboring F- ions are replaced by one Al3+ ion and two O2- ions. This may be pictured schematically as: F F F F F F F Al F Na F Al F ,-Na+ + Al8+ F Al 0 A1 0 A1 F F F F —2 F- + 2O2- F F F solid cryolite cryolite-alumina solid solution This means that the complex in the solid solution, derived from X-ray and density measurements, is the same as that which Forland, Storegraven, and Urnes derived from equilibrium measurements in the liquid state. References IT. Forland, H. Storegraven, and S. Urnes: Ztsch. fur anorgan-ische und allgemeine Chemie, 1955, vol. 279, p. 205. 2J. J. Stokes: AIME Trans. To be pubhshed. s E. Zintel and W. Morawietz: Ztsch. pubhshed.fur anorganische und allgemeine Chemie, 1939, vol. 240, p. 145.

Jan 1, 1958

By Joseph M. Dawson

Although there was a very great increase in drilling activity along the fault line of south Texas during 1937 as compared with the previous three or four years, and although seven new fields were discovered, it cannot be said that any major development of importance took place. There were slightly over 550 completions during 1937, of which nearly 350 were oil wells as compared with some 275 the preceding year, of which 169 were oil wells. This increase in drilling activity was occasioned almost entirely by the greater interest in and development of Austin chalk production, principally in Caldwell, Guadalupe and Bastrop Counties. Seven fields were found, of which a brief description is given in Table 3. None has as yet assumed anything of major importance, and it is doubtful whether any will be classified as major discoveries through further development. Two were producing from the Edwards limestone, one from serpentine and the other four from the Austin chalk; the latter may be classified as extremely erratic in nature. The major discouraging feature of the year was the rise and subsequent fall of interest and importance of Austin chalk production. Many new operators came into this district to drill and produce Austin chalk oil toward the first of the year, but in the latter months the production decline from this formation was so rapid and the production so erratic that drilling operations fell off materially and interest largely abated. This was particularly true of the Branyon field in Caldwell County, and the same statement is applicable to the Pearsall field, Frio County. The latter field, covering some 5000 acres and owned and controlled entirely by the Amerada and Rycade, had early completions from the Austin chalk as high as 22,000 bbl. per day. The decline was extremely rapid and the maintained production from 17 wells is only around 700 bbl. per day after a total recovery of less than one-half million barrels. Present estimates of recoverable oil from Chalk vary from 2000 to 5000 bbl. per acre. A new process for the completion of producing wells from the Edwards limestone, particularly applicable to old producing areas, was developed, in that the penetration of the Edwards lime in drilled wells is now only 1 or 2 ft. as compared to between 15 and 75 ft. in wells drilled several years ago. Many new wells have been drilled in old Edwards lime producing

Jan 1, 1938

By F. P. Donohue

The observations and data presented in this paper are the result of extensive study of flowing wells, most of which were in the Maracaibo Lake Basin of Venezuela. The Lago Petroleum Corpn. had extensive production in this area, gas-oil ratios were low, and the problem was to determine whether by careful handling of the wells with respect to flowing conditions and by conserving the gas, the oil production of the wells could be maintained by natural flow until it had declined to a rate which could be handled with an ordinary working barrel, thereby avoiding the high cost of gas-lift equipment installation in the lake bed. The problem was complicated by the nature of the wells themselves. Production is from soft, comparatively unconsolidated sands, necessitating screen pipe in all wells. It was not only necessary to keep the wells flowing but to keep them flowing without heading, as the release of pressure upon making a head brought large quantities of sand into the wells, sanding them up or possibly cutting out the screen pipe. In furtherance of the plan of keeping wells flowing as long as possible, each well was equipped with a casinghead and tubinghead recording pressure gage, and an oil and gas separator set. About one-half of the wells were equipped with gas meters. All wells were tubed before bringing into production. Frequently individual gages were taken on each well. A large scale chart was plotted for each well, showing daily oil production, gas production, gas-oil ratio, tubinghead pressure and casinghead pressure. Any deviation from the normal was immediately checked and the condition remedied if possible. Theory of Flowing Wells Based upon considerable study of these records, it is believed that the flow of a well actuated by gas is mainly a problem in velocity, a certain minimum velocity in the flow string being necessary for the gas to carry the oil. If this minimum velocity is not obtained the oil drops back and the well heads or goes dead. The point of minimum velocity is of course at the bottom of the tubing, where the gas is under the highest pressure and therefore occupies the least volume. Some years ago when the success of the gas-lift at Seminole was so pronounced, there was considerable broadcasting of the statement that

Jan 1, 1930

By F. Lynwood Garrison

The future of the Witwatersrand depends upon the possibility of mining and milling profitably the large tonnage of relatively low-grade gold ores known to exist in that area. The problem must be solved if the existence of the gold-mining industry in South Africa is to be saved and continue. To show that this disaster may be avoided, or at least postponed for another decade or longer, the following official statement is of interest: "There is a fairly large area of possible orebody on the East Rand of whose value and depth from the surface we have some though not very accurate knowledge. There is a far larger area south of the Central Rand which probably carries much payable ore, but at depths that at present appear too great to mine. Finally, there is a narrow strip of country over 100 miles in length stretching south from the Rand to Klerksdorp and beyond, which may contain large ore-bodies. The Witwatersrand rocks outcrop over portions of this ground and in places conglomerates occur in it that carry small bodies of payable ore. There is reason to believe that conglomerates of the Witwatersrand system exist over all this strip, though they are for the most part covered by later sediments. It seems probable also that there are large blocks of payable reef in this belt, at any rate in the area that lies close to the present western limit of the developed mines. The structure in this neighborhood is however very complicated and to prove the orebodies will be both difficult and costly." Ores in the Witwatersrand It should be explained in this connection that the conglomerates mentioned here were originally old gravel beds now consolidated into bedded sedimentary rocks, very hard because strongly cemented with secondary silica. The gold exists in this cement and is rarely found in the pebbles composing the rock or bed called locally reef. It is important to realize that these gold deposits are beds; not veins as generally understood by mining engineers and geologists. In addition to these low-grade ore reserves we have also to consider the ore left behind in the old stopes of the upper levels near the surface,

Jan 1, 1931

By A. Gatti

A dispersion of AI2O3 was produced within chromium by the hydrogen reduction of a solid solution of Cr2U3-A1203. The yesulting powder. was compacted, extruded, and the material tested in tension at various temperatures and in creep at 1800°F. The material is ductile above 1200°F and is at least twice as strong as electrolytic chvomium at all temperatures. Its creep resistance, rupture strength, and ductility at 1800°F warrant further work to improve its Low -temperatutre properties. BECAUSE of its high melting point and excellent corrosion resistance, chromium has long been considered as a base for high-temperature alloys. Most chromium base alloys, however, are extremely brittle at low temperatures. Elements such as nickel and iron lower the melting point of chromium and thereby limit its high-temperature usefulness. Chromium-alumina materials made by othersl, 2 have shown good high-temperature creep resistance but poor ductility and thermal shock resistance. Pure ductile chromium3 is weak at high temperatures and reverts to a brittle state if exposed to nitrogenous atmospheres. In sintered aluminum powder (SAP)4 and internally oxidized alloys of silver, copper, and nickel, fine dispersions of oxide phases can control hardness, recrystallization, and yield stress. The possibility of formation of a ductile, high-strength material by precipitating dispersions of alumina in a chromium matrix appears worthy of investigation. MATERIAL Powder Production—Chromium oxide and alumina in amounts to produce a final alloy of Cr + 16 pct AI2O3 by weight were colloid milled, filtered, dried and high fired for 16 hr at 1600°C in air. The resulting solid solution of oxides was ball-milled to a fine powder and the chromium oxide reduced to chromium by heating in pure dry hydrogen for 64 hr at 1400°C. Final Materials Produced by Powder Metallurgy Techniques—-Chromium powder, containing a disper-sion of alumina, was pressed into 1 1/8-in. diam slugs at 25 tons per sq in. and sintered 16 hr at 1400° C in pure dry hydrogen. The sintered slugs were encased in a stainless steel can, 2 in. in diam, and extruded at 1200° C through a 1/2-in. die. The 16 to 1 extrusion ratio produced a final chromium-alumina rod 1/4 in. in diam about 30 in. long. Samples of the rod were plunge-ground to small rupture bars of 0.82-in. gage length with a 0.01-sq-in. cross section. RESULTS Microstructure Studies—Fig. 1 is the microstruc-ture of the material in the as-sintered condition while Fig. 2 is the microstructure of the material as-extruded. Comparison of the as-sintered and as-extruded micrographs show the redistribution and realignment of the alumina inclusions by the extrusion

Jan 1, 1961

By Norman Ketzlach

ANGANESE today overshadows all strategic materials in our planning for national se-curity," according to a report issued recently by the American Manganese Producers Association. By far the greater part of the manganese ore used in the United States is imported. "We have enough manganese ore in the United States to last from one hundred to three hundred years and longer, but most of the deposits are undeveloped. As in the case of copper, lead, and zinc, manganese ore, both foreign and domestic are low grade. Manganese ores have to be concentrated and processed. After being processed, domestic ores are higher grade than foreign." Most of the manganese ore found in this country, however, is not amenable to concentration by ore-dressing methods. Manganese Products, Inc. has developed a sulphurous-sulphuric acid leaching process for the recovery of manganese from low-grade, intermediate manganese ores. By the term "intermediate manganese ores" is meant those ores in which the manganese in the form of manganese oxides is found to have two different valences, usually two and four, as is probable in Mn,O, or the ore may be a mixture of manganous and manganic oxides. "Intermediate" manganese siliceous ores are ores in which the silica is a constituent of the ore and is loosely linked to the manganese by water of crystallization. This process has been carried out with the type of manganese ore found in the Olympic Peninsula of western Washington; Clough, N. C.; and Lava Hot Springs, Idaho, as well as just recently with manganese ore from Las Vegas, Nev. As far as the manganese leaching process is concerned, these ores differ primarily in the form in which the manganese oxides occur. The tetravalent manganese, the manganese existing in the dioxide form, is soluble in a sulphurous acid solution. To dissolve the divalent manganese, sulphuric acid is required. To dissolve the type of ore found in Washington and North Carolina, a mixture of both sulphurous and sulphuric acid is used. Whereas to dissolve the type of manganese ore found in Idaho and also in Montana, sulphurous acid alone is sufficient. The Nevada manganese ore is of the same type as that found in Idaho as far as the leaching process is concerned. It has long been known that manganese ores, with the exception of rhodonite, which is a true manganese silicate ore, can be dissolved readily in sulphurous and sulphuric acids.' The removal of the impurities such as silica, iron, and alumina from the resulting solution is the step that has been difficult. The process worked out by Manganese Products has been carried through pilot-plant equipment. This process has also been extended to the production of ammonium sulphate. Leaching of Ore: The manganese ore, ground to —-65 mesh is leached with sulphurous acid and sul-

Jan 1, 1951

By Theron Wasson

The year 1942 in Michigan was devoted largely to the development of fields discovered in 1941 but was also characterized by a great increase in prospecting for new productive horizons below the Dundee limestone. Some new fields were discovered but as yet these have shown few signs of being of major importance. Michigan's total production for 1942, of 21,754,000 bbl. of oil, as reported by the U. S. Bureau of Mines, was second only to the record year of 1939 when 22,799,000 bbl. of oil were produced. All important fields were prorated throughout the year, and it is obvious that without proration a new all-time high would have been established for the state this year. From 1925 to the end of 1942, Michigan has produced annually the following amounts of oil: Year Barrels Source 1925 4,000 1926 94,000 1927 435,000 1928 592,000 1929 4,641,000 1929 Michigan Geological Survey 1930 3,928,000 3,785,000 1932 6,925,000 1933 7,942,000 1934 0,603,000 1935 15,776,000 U.S. Bur. Mines, 1937 1936 11,928,000 U.S. Bur. Mines, 1938 1937 16,628,000 U.S. Bur. Mines, 1939 1938 19,211,000 U.S. Bur. Mines, 1938 1939 22,799,000 1940 19,764,000 1941 16,361,000 1942 21,754,000 Total 183,170,000 This tabulation shows the steady growth of the industry in Michigan since the first discovery of oil in 1925. Maes A map of the oil and gas fields of Michigan in 1941, published in the report for 1942, shows the main producing areas and should be referred to if information in regard to their location is desired.* The main producing zones were shown in the columnar section in the same publication. Development in Fields Reed City Field.—During 1942 the Reed City field, which ended 1941 with 112 producing oil wells, added 70 new producers to bring the total at the end of the year to 182 wells and 4700 proven acres. A south extension of the field developed during the year was in large part responsible for the increase. Approximately 9,000,000 bbl. of oil was produced from the field during the year, bringing the total accumulated production to the end of the year to roughly 11,750,000 barrels. Headquarters Field.—The Headquarters field, which started the year with ro producing oil wells, ended the year with 41 wells aid 1240 proven acres. Approximately 2,300,000 bbl. of oil was produced in 1942. Kawkawlin Field.—Although not a 1941 discovery, the Kawkawlin field has been actively developed on the 40-acre spacing plan during the last year, 42 producers having been completed, bringing the total number of wells at the end of the year to 77. Nearly 500,000 bbl. of oil was produced during the year.

Jan 1, 1943

By W. J. Kroll

W. J. Kroll (Belgium)—Those who are acquainted with the metallurgy of our forefathers may have occasionally a good time when glancing at recent publications in which aged discoveries are unconsciously reported as novelties. We know very well, that oxygen blowing of iron has been described by old Bessemer. The author of the present article is, however, not aware of the fact that the process he describes, the fused salts scrubbing, was already used in the middle of the last century by St. Claire Deville in his attempts at making higher-purity aluminum from raw AlCl3 by sodium reduction. The same fact escaped the three investigators to whom the author refers. The technical grade AlC13 produced by St. Claire Deville from impure oxide, chlorine, and carbon (Oersted process) was contaminated with Sic4 and FeC13, which he removed on an industrial scale by various methods.' He sublimed, for instance, his chloride in contact with iron nails, or aluminum chips, or in hydrogen, which reduced the FeC13 to the less volatile FeCl2. He used also alkali-alkaline earth chlorides as a solvent for A1C13 and FeC13 in presence of iron as a reducing agent, and sublimed his purified AlC13 from solvent salts. The successors of Deville used also zinc or lead as a reducing agent. These methods were later used currently for the purification of BeCl2 and for collecting this compound in a salt bath, suitable for fusion electrolysis. More recently, the same Deville process has been described as applied to the purification of ZrCL4, as part of a method of extraction of ZrCL4 from silico zirconium, which later was reacted with FeC12 in a separate part of the equipment. According to the patent referred to3 the ZrCL4 is dissolved as a gas in a carrier salt such as alkali-alkaline earth chloride, from which it can be reclaimed in a purified form by distillation. A bath of NaCl/KCl is recommended in the specifications. The FeC12-FeC13 go in the salt solution in which raw ZrCl4 is introduced by bubbling, while Sic4 and Tic4 pass through the bath and escape in the atmosphere. purification by this salt-solvent method is thus well described. It may be worth while insisting on some minor details about which the author did not bother too much. One of these concerns the material of construction for the container. If iron is used, and if no other reducing agent is added, then it is the iron of the pot that acts as a reagent in the breakdown of FeC13 to FeCl2, and corrosion can be expected. This shows the importance of using extraneous large surface-reducing agents, of which there is a choice. Zir-

Jan 1, 1963

By D. H. Polonis, M. B. Kasen

AN unusual thermal etching phenomenon has been observed on the surface of a Cu-Si alloy. The observations were made during studies of vacancy condensation pit formation which were reported in previous papers.1,2 Figs. 1 and 2 are photomicrographs of the surface of a Cu-4.8 pct Si alloy after heating in vacuo (3 x X mm Hg) to 525°C and subsequently holding at that temperature for 16 hr in an impure (air-contaminated) argon atmosphere. Under these conditions preferential removal of silicon from the matrix by oxidation results in a surface which is entirely a phase overlying an a plus y structure. The light areas of Fig. 1 are regions in which very little thermal etching has occurred, while the majority of the surface has experienced severe etching. Similar regions in Fig. 2 are seen as plateaus above contours produced by net transfer of material from the specimen surface. Twin boundaries are also visible in Fig. 2. The difference in matrix mi-crostructure between Figs. l and 2 reflects the par- ticular orientation of low-index planes with respect to the surface of observation. Thermal etching contours of this type have been studied in detail by Hondros and Moore Both of the photomicrographs show that one or more dark spots are located approximately at the center of every protected area; where two spots are in close proximity, the protected areas have merged. The microstructures indicate that the anomalous resistance to thermal etching is related to the presence of these spots. Williams and Hayfield have shown that local regions of unusually high oxidation resistance can be caused by a surface monolayer of atoms with a work function higher than that of the base material. The result is an inhibition of the rate of electron removal from the base material and a decrease in the oxidation rate. The source of the protected layer may be either surface diffusion from contaminants on the specimen surface or pipe diffusion of solute atoms followed by migration across the surface. In the latter case the driving force is a difference in chemical potential resulting in a Gibbs adsorption phenomenon. In the present case, chemical polishing of the specimen surface precluded contaminants of a strictly surface nature. Consequently, diffusion of impurity atoms from within the lattice appears to be the most tenable explanation of the observed phenomena. The authors propose that the structures of Figs. 1 and 2 reflect the diffusion of impurity atoms along extended dislocations within the individual a phase grains prior to surface oxidation. The central spots within the protected regions are seen as sites of dislocation emergence which have become locally decorated with oxide in the manner discussed in Ref. 1. Williams and Hayfield observed protected regions adjacent to the grain boundaries of iron-contaminated copper which they attributed to the segregation of iron to the grain boundaries coupled with high dif-fusivity along the complex dislocation array at such boundaries. No evidence of such grain boundary protection was observed in the Cu-Si alloy; this

Jan 1, 1964

By W. A. Thomas

Steam is, and doubtless always will be, the basic power in the anthracite industry, either directly applied through engines and pumps or electrically. The rapidity with which electric power is being applied to the mining and preparation of anthracite leaves little doubt as to its utility and economy. There is practically no operation, except possibly the drilling of hard rock, that has not been successfully electrified and the matter of drilling is handled economically with electrically driven compressors and the standard compressed-air drills. Conservation and the seemingly ever-increasing cost of production, justify careful consideration of the possible results of the more extensive use of electric power in the industry. It is not planned to discuss, herein, the relative economies of individual applications but to consider the relative economy and flexibility of steam and electric power. The reports available for the year 1920 indicate a production of slightly over 80,000,000 tons of anthracite, of which 8,843,500 tons were used for power and heating purposes; in other words, over 11 per cent. of the production was used at the mines. Some of this was used to generate electric power at the mines, about 160,000,000 kw-hr., while 150,000,000 kw.-hr. was purchased from the public utility companies. One large producer, who is buying some electric power and generating some, used over 13 per cent. of the production for power and heating at the mines. Another producer, where considerable electric power is generated on the properties, is using less than 9 per cent. of the output for power and heating. One of the largest producers has a fuel consumption of over 15 per cent. of the output, besides which considerable power is purchased. A careful study of the field indicates that steam-operated plants use upwards of 13 per cent. of the production for power and heating, while electrically operated plants use about 1 per cent. for heating; so that, for steam-power purposes at least 12 per cent., or 268.8 Ib., are used for power out of each ton produced. In the complete electrification of anthracite mining operations, no set rule can be given for the power requirement, in kilowatt-hours per ton, as conditions vary widely in the matter of pumping, ventilation, and transportation, but the following cases are given as a basis of determining a range and a possible average power requirements:

Jan 1, 1922

By M. Van Siclen

THE outstanding fact in connection with dust disease in. the United States at present is the growing recognition of its seriousness by state officials and by the more progressive operators of mining, metallurgical and allied industrial plants. The same may perhaps be said of labor in some. of its better organized centers, but the average independent non-. union workman continues, as of yore, to suffer the toll of disability and. even of death from dust inhalation without realization of the source of his ill-being. Progress in the betterment of the handling of sufferers from dust disease and of the conditions creating dust hazards in mining and allied industries is pursuing a course similar to that of the now widespread campaign against accidents, in which the risk is more obvious, more severe, and was naturally recognized sooner. The coming on of dust disease is generally relatively slow and its immediate effects not infre-quently masked by or attributed to other diseases. Marked exceptions to this general rule have occurred in districts where the dust is particularly pernicious, such as the Rand and Joplin; yet such exceptions, unhappy in themselves, opened the eyes of medical men, and of those in other localities charged with the responsibility for the welfare of industry, to the much more widespread if less spectacular hazard existing from the inhalation of. dust in all rock-excavating operations and all industrial operations creating inorganic dust, whether it be crushing and grinding, sand-blast-ing, granite-cutting, or what not. Advancement to date in the United States in prevention and treat-ment has been slow, yet the record shows that quantitative methods for determining the degree of hazard and means for decreasing it were being developed as far back as 25 years ago; and that more rapid progress may be looked for from now on. In 1908, in this country; F. L Hoffman?(1) discussed the mortality from consumption in dusty trades, especially brass foundries; and in 1913.E. R. Hayhurst(2) described the effects of inhalation

Jan 1, 1933

By Irving Fatt, Robert J. S. Brown

INTRODUCTION The wettability of reservoir rocks is recognized as one of the major factors that determines their multiphase flow properties. Multiphase flow properties in turn govern reservoir performance. For this reason, the reservoir engineer is vitally interested in the wettability of reservoir rock. The production research scientist is interested in wettability because the solution of the problem of improving waterflood recovery by use of surface-active additives may hinge on a detailed understanding of the wettability of reservoir rock. Early workers believed that all reservoir rocks were preferentially water wet. Continued study soon uncovered certain rocks which had flow properties that indicated that they were preferentially oil wet. Recent studies show that there is a spectrum of wettability. Some reservoir rocks have multiphase flow properties which indicate that they have an intermediate wettability. The differences in recovery observed among different reservoirs may, in part be the result of small differences in wettability. Differences in wettability amcng reservoir rocks may be the result of differences in the fraction of the total surface area that is preferentially oil wet and preferentially water wet. Nuclear magnetic relaxation measurements may provide a method for determining the fraction of preferentially oil wet and preferentially water wet area in porous media. Measurements to be reported here were made on water-saturated unconsolidated sand packs which were mixtures of preferentially oil wet and preferentially water wet sands. The resulting data show definitely that the fraction of each wettability in these sand packs can be determined by this nondestructive method of measurement. THEORY OF NUCLEAR MAGNETIC RELAXATION The details of the theory of nuclear magnetic relaxation have been presented previously1. In this paper, only a very brief review of the theory will be given to show its application to the measurement of fractional wettability. Nuclear magnetic relaxation is a process of adjustment undergone by certain atomic nuclei when their magnetic environment is changed. They adjust, or relax, to be in equilibrium with a new magnetic field. The reason that some atomic nuclei are affected by a magnetic field is that they themselves behave in some respects like tiny magnets. In particular the proton, the nucleus of the hydrogen atom, behaves as a magnet. The proton spins, somewhat as the earth spins on its axis. The spinning charge produces a magnetic field just as current traveling in a loop of wire produces a magnetic field. No net charge is required, however; for instance, the neutron has spin and magnetic moment. When the spinning proton is subjected to an externally applied magnetic field, its axis tends to line up with the magnetic field, somewhat as a compass needle tends to line up, but the spinning proton cannot do this as easily as the needle can. The proton also has mass, and its spinning mass makes the proton behave somewhat like a gyroscope. As is well known, a force which tends to change the axial direction of a gyroscope merely causes the gyroscope to precess: lhat is, the axis begins to trace out a conical surface. The gyroscope cannot actually assume the position suggested

Jan 1, 1957

By Theron Wasson

The year 1942 in Michigan was devoted largely to the development of fields discovered in 1941 but was also characterized by a great increase in prospecting for new productive horizons below the Dundee limestone. Some new fields were discovered but as yet these have shown few signs of being of major importance. Michigan's total production for 1942, of 21,754,000 bbl. of oil, as reported by the U. S. Bureau of Mines, was second only to the record year of 1939 when 22,799,000 bbl. of oil were produced. All important fields were prorated throughout the year, and it is obvious that without proration a new all-time high would have been established for the state this year. From 1925 to the end of 1942, Michigan has produced annually the following amounts of oil: Year Barrels Source 1925 4,000 1926 94,000 1927 435,000 1928 592,000 1929 4,641,000 1929 Michigan Geological Survey 1930 3,928,000 3,785,000 1932 6,925,000 1933 7,942,000 1934 0,603,000 1935 15,776,000 U.S. Bur. Mines, 1937 1936 11,928,000 U.S. Bur. Mines, 1938 1937 16,628,000 U.S. Bur. Mines, 1939 1938 19,211,000 U.S. Bur. Mines, 1938 1939 22,799,000 1940 19,764,000 1941 16,361,000 1942 21,754,000 Total 183,170,000 This tabulation shows the steady growth of the industry in Michigan since the first discovery of oil in 1925. Maes A map of the oil and gas fields of Michigan in 1941, published in the report for 1942, shows the main producing areas and should be referred to if information in regard to their location is desired.* The main producing zones were shown in the columnar section in the same publication. Development in Fields Reed City Field.—During 1942 the Reed City field, which ended 1941 with 112 producing oil wells, added 70 new producers to bring the total at the end of the year to 182 wells and 4700 proven acres. A south extension of the field developed during the year was in large part responsible for the increase. Approximately 9,000,000 bbl. of oil was produced from the field during the year, bringing the total accumulated production to the end of the year to roughly 11,750,000 barrels. Headquarters Field.—The Headquarters field, which started the year with ro producing oil wells, ended the year with 41 wells aid 1240 proven acres. Approximately 2,300,000 bbl. of oil was produced in 1942. Kawkawlin Field.—Although not a 1941 discovery, the Kawkawlin field has been actively developed on the 40-acre spacing plan during the last year, 42 producers having been completed, bringing the total number of wells at the end of the year to 77. Nearly 500,000 bbl. of oil was produced during the year.

Jan 1, 1943

By J. C. M. Li

A dislocation model is constructed for a cylindrical tilt boundary of which the axis of tilt is parallel to the axis of the cylinder. The strain energy per unit area calculated from this model agrees with thut of an infinite vertical wall of edge dislocations. Based on this model, a dislocation mechanism for the shrinking of such a cylindrical boundary is proposed. The power relation between the grain boundary velocity and the driving force is accounted fm by the stress dependence of dislocation velocity. The activation area for grain boundary motion is found to correlate with that .for Creep in aluminum. In the preceding paper' the velocity of a curved grain boundary is found to be a power function of the driving force, [1] where M is the velocity at unit driving force, y is the grain boundary energy, and p is the radius of curvature. This finding adds another nonlinear rate equation to metallurgical phenomena. While a macroscopic theory for the steady state as just presented2 can be used to understand the shape of the moving boundary, such theory usually does not provide any information about the atomistics of the process. It is attempted in this paper to discuss the nonlinear rate equation in terms of a dislocation mechanism. A DISLOCATION MODEL FOR A CYLINDRICAL TILT BOUNDARY Before a dislocation mechanism can be proposed for the motion of a cylindrical tilt boundary, it is necessary to construct a dislocation model for the boundary. For simplicity, a tilt boundary in a simple cubic lattice will be examined. Although this does not represent the situation in aluminum, it is expected that the general features will be similar. The details of the model in the fcc lattice can be constructed when a refinement of the simple model is called for. A cylindrical low angle tilt boundary in a simple cubic lattice is shown in Fig. 1. Two sets of edge dislocations are needed as shown. A schematic representation is shown in Fig. 2(a). In terms of a continuous distribution of dislocations, the density of dislocations n, of Burgers vector b, in the small segment ds of the grain boundary is Similarly the density of dislocations n, of Burgers vector bz in the same segment ds is where is the tilt angle of the grain boundary. Based on this continuous distribution of dislocations in the grain boundary, it can be shown that the interaction between a small segment of the boundary and the rest of it is zero. Furthermore, the stress produced at any point inside or outside the cylinder is also zero. This shows that the model is acceptable in the sense that the boundary has no long-range stresses. Since the model of continuous distribution of dislocations in the grain boundary does not reveal the interactions among individual dislocations, a discrete dislocation model has to be used for such purpose. For simplicity, an equivalent model is shown in Fig. 3. This arises because the total Burgers vector is, from

Jan 1, 1970

By W. C. Ellis, E. S. Greiner

WHEN metallic materials are deformed plastically, the process may be considered as one in which hardening and recovery occur simultaneously. The net hardening is that produced by deformation in the absence of recovery lessened by recovery during and immediately following deformation. Strain hardening takes place through movements of large groups of atoms acting to a degree as an entity. A complex microstress system is developed. Recovery is a diffusive-type process involving single atoms or, at most, only a few atoms in concerted action. This is accompanied by elastic strain relaxation. Recovery is strongly temperature-dependent. The driving energy for the process resides in thermal fluctuations of the atoms augmented by the energy of the stress field producing the deformation, and by that produced by the deformation. At very low temperatures recovery is essentially absent, or very small. At high temperatures in the hot working range, recovery is so rapid that deformation results in no appreciable net hardening. The interplay of strain-hardening and recovery results in differing end structures depending on the temperature and the strain rate of the process. For example, there is a prominent difference in the spacing of the slip markings and in the detail of X-ray diffraction patterns. High temperatures and slow strain rates favor a wide spacing of slip markings and sharp reflections.',' This suggests that change in rate of the recovery concurrent with deformation modifies to a degree the manner of the deformation. Different slip systems may operate. For very slow rates, the mechanism may, as has been suggested, differ from that of "classical slip." In the experimental work that follows the findings will be interpreted from the point of view developed in this section. Recovery and Electrical Conductivity Electrical conductivity is a sensitive indicator of the state of strain in a material3' * and was used in this investigation. The materials studied in wire form were: OFHC copper, a high purity (99.99 pct) and 2s grade aluminum, and grade A nickel. Wire annealed and initially 0.050 in. in diam was drawn through diamond dies in a simple holder maintained at 25", —75°, or — 195°C. Precautions were taken that for each material all conditions of drawing were the same except the temperature. Electrical resistivity was measured for each condition at 20°C. This was done as soon as practical after drawing to minimize possible room temperature recovery. The data for the four materials are plotted in Fig. 1 in terms of the change in resistivity for drawing at the several temperatures. The effect of temperature of drawing on the increase in resistivity is most pronounced for copper. Drawing at 25°C to 80 pct reduction in area increases the resistivity approximately 2 pct; drawing at —195°C to the same reduction increases the resistivity about 6 pct. The increase in resistivity" & in this metal is due to extra scattering of conduction electrons originating in the lack of orderly arrangement of the atoms induced by the deformation process. It has been suggested

Jan 1, 1953

By L. C. De Jong, J. F. Shirley, M. L. Campbell

At the Southern Peru Copper operation in Toque-pala, Peru, a new process flowsheet for the recovery of byproduct molybdenite has proved successful in dealing with complex and highly variable ores. This paper describes the process and the functions of each of the chemicals used. The Toquepala concentrator of the Southern Peru Copper Corp., located approximately 720 miles southeast of Lima near the Chilean border, processes a daily 36,500 tons of ore containing between 0.50 and 3.00% copper. The molybdenite content in the ore also varies greatly ranging from essentially nothing to as high as 0.15%. The 1966 yearly averages were approximately 1.20% copper and 0.03% molybdenite. The Toquepala porphyry deposit is a mushroom-shaped ore body consisting of a flat-lying enriched zone of predominant chalcocite with a stem-like extension of hypogene chalcopyrite ore in depth within and around a large breccia pipe.1 The underlying chalcopyrite ore has not been reached; however, due to the presence of a major post orebody fault, predominantly chalcopyrite ore is present in the north side of the pit. Most of the molybdenite occurs either as small, fine granular, pulverulent masses in vugs or empty voids of breccia, or as thin foliated masses and narrow thread-like filling in rock joints and fractures. The normal occurrence of quartz gangue with the molybdenite gives some basis for correlating the molybdenite mineralization to some later periods of silicification. On April 18, 1962, the molybdenite recovery plant at Toquepala went on stream, approximately 27 months after the copper concentrator had been in production. The plant was designed and built by Southern Peru Copper Corp.'s engineering and mechanical departments. The basic method chosen for separating the molybdenite from the copper concentrate was the sodium hypochlorite-sodium ferrocyan-ide process. The selection of this process was based on the results of an extensive testing program performed by the Colorado School of Mines Research Foundation, Inc. and the economic conditions of the area. The originally designed process could never be fully implemented due to a lack of sodium hypo-chlorite and has had to be continually modified to satisfy the requirements of the kaleidoscope of ores from the mine. The three basic problems that plague the operation of any molybdenite recovery plant are all present at Toquepala in large measure. Both the quantity of plant feed and the quantity of molybdenite contained in the plant feed are continuously changing. Even more detrimental to an efficient operation is the fact that the copper mineralization in the feed frequently changes once in every 24 hours and occasionally once a shift. From the point of view of the molyb-

Jan 1, 1968

By Norman Ketzlach

ANGANESE today overshadows all strategic materials in our planning for national se-curity," according to a report issued recently by the American Manganese Producers Association. By far the greater part of the manganese ore used in the United States is imported. "We have enough manganese ore in the United States to last from one hundred to three hundred years and longer, but most of the deposits are undeveloped. As in the case of copper, lead, and zinc, manganese ore, both foreign and domestic are low grade. Manganese ores have to be concentrated and processed. After being processed, domestic ores are higher grade than foreign." Most of the manganese ore found in this country, however, is not amenable to concentration by ore-dressing methods. Manganese Products, Inc. has developed a sulphurous-sulphuric acid leaching process for the recovery of manganese from low-grade, intermediate manganese ores. By the term "intermediate manganese ores" is meant those ores in which the manganese in the form of manganese oxides is found to have two different valences, usually two and four, as is probable in Mn,O, or the ore may be a mixture of manganous and manganic oxides. "Intermediate" manganese siliceous ores are ores in which the silica is a constituent of the ore and is loosely linked to the manganese by water of crystallization. This process has been carried out with the type of manganese ore found in the Olympic Peninsula of western Washington; Clough, N. C.; and Lava Hot Springs, Idaho, as well as just recently with manganese ore from Las Vegas, Nev. As far as the manganese leaching process is concerned, these ores differ primarily in the form in which the manganese oxides occur. The tetravalent manganese, the manganese existing in the dioxide form, is soluble in a sulphurous acid solution. To dissolve the divalent manganese, sulphuric acid is required. To dissolve the type of ore found in Washington and North Carolina, a mixture of both sulphurous and sulphuric acid is used. Whereas to dissolve the type of manganese ore found in Idaho and also in Montana, sulphurous acid alone is sufficient. The Nevada manganese ore is of the same type as that found in Idaho as far as the leaching process is concerned. It has long been known that manganese ores, with the exception of rhodonite, which is a true manganese silicate ore, can be dissolved readily in sulphurous and sulphuric acids.' The removal of the impurities such as silica, iron, and alumina from the resulting solution is the step that has been difficult. The process worked out by Manganese Products has been carried through pilot-plant equipment. This process has also been extended to the production of ammonium sulphate. Leaching of Ore: The manganese ore, ground to —-65 mesh is leached with sulphurous acid and sul-

Jan 1, 1951