Search Documents

By J. S. Miller

THIS paper describes the method of mining a steeply pitching anthracite seam on a heavy pitch in the Orchard vein in No. 1 Tunnel of the Lehigh Coal and Navigation Co. The Orchard vein in the Nesquehoning district has a thickness of about 15 ft. on the level of the gangway, which is sufficient thickness for the gangway to be driven full width in coal. Above the gangway, the vein becomes thinner and near the surface is about 8 ft. thick. The coal is of good hard quality and carries a fairly good roof. The pitch of the vein is between 65° and 70°. Usually the breast-and-pillar method has been employed in the mining of the steeply pitching veins in this section. This method produced good results as far as the mining of the breast was concerned but the recovery of the pillar was difficult as to full extraction and expensive as regards costs. To recover these pillars after the breasts were driven, three methods were commonly employed; they were known as the pillar-breast method, pillar-skipping method, and pillar-chute method. The pillar-breast method consisted in putting a battery in one corner of the pillar (Fig. 1), coupling the manways A and B of the two adjacent breasts for two or three lengths ahead of the working face of the pillar being cut, and working the pillar as a breast. This method was used by the more skilled miners of the earlier days but has practically been abandoned. A slight variation of this method is used to some extent. In this case, the pillars are left wider than ordinarily and of sufficient width for the full-width breast to be driven in and a small pillar left on each side of the pillar breast between it and the regular breasts. With the completion of the "pillar breast," the ribs are drilled full of holes, loaded, and fired.

Jan 3, 1925

By P. A. Boeck

(San Francisco Meeting, September, 1915) THE thermal insulation of high-temperature equipment for industrial purposes is a subject that has not received from engineers and designers the attention its importance deserves. This may be attributed to a number of causes: In the first place, heat flow is a rather difficult factor to measure under the working conditions of an industrial furnace, and until the comparatively recent introduction into certain operations of the heat balance sheet, with a systematic attempt to account for the discrepancies in the totals, the various causes of heat losses and the reasons for their existence were not brought to light. Moreover, such rapid advancement and radical changes in the design of equipment, especially in metallurgical lines, have occurred that practice has apparently outdistanced the theory of design. In the modern tendency toward greatly increased size of units, effort has seemingly been made to utilize the heat of fuel gases without proper. attention having been paid to conserving heat energy and confining it strictly to the points of maximum activity. The systematic study of the thermal properties of structural materials, which is being carried out by various government bureaus and also by a number of technical societies, is forming the basis for more intelligent and consistent work in the economically important subject of prevention of fuel waste.

Jan 8, 1915

By E. P. Shea

The Anaconda Co.'s Geological Department at Butte, Mont., was started early in the Company's history because of litigation involving vein ownership and extralateral rights. The problems, some of which were resolved in courts, were many because of the large number of veins and lode locations. Defensive action was required to prove ownership and protect against illegal exploitation of the downward and extra-lateral extensions of the ore bodies. In many cases it was necessary to define the outcrop of the vein and to show that its apex was within the boundaries of the lode claim. Exhibits illustrating geology were needed to present the cases clearly, and these could be made only after careful inspection and mapping of the underground workings by competent geologists. Also, The Anaconda Co. was one of the first companies to recognize the worth of skilled mining geologists and the value of accurate records in the search for new ore. The department was organized in 1900 by H. V. Winchell who, with D. W. Brunton, worked out the methods. Reno Sales was Chief Geologist from 1906 until 1948 when he was succeeded by V. D. Perry, the present Chief Geologist. Under their direction, F. A. Linforth, M. H. Gidel, C. H. Steele, E. P. Shea, C. C. Goddard, Jr., and W. A. O'Brien enlarged the scope of the work and improved the technique.

Jan 3, 1961

For some time attempts have been made to improve drilling efficiency (and therefore reduce costs) by introducing certain reagents to the flushing medium. Much of this interest is the result of the Russian book, Hardness Reducers in Drilling, by Rehbinder, Schreiner, and Zhigach, published in 1944. Before embarking on full-scale drilling tests, it was decided to investigate the effects on the tensile strength; these results would help in the selection of the proper reagent and its optimum concentration. Selection of Tensile Strength Testing A drilling system basically performs two separate operations: 1) Breakage of rock. 2) Removal of the broken pieces of rock. Both affect drilling and drill performance but are distinct and separate phases of the process. Causing rock to break during drilling is a matter of generating sufficient stress with a drill bit to exceed the strength of the rock. This strength of the rock may be termed its drilling strength; it is not equivalent to any of the well-known strength parameters. Various criteria have been employed to measure the efficiency of a given drilling system or for comparing different systems and one of the most important criteria is "speed of drilling." Speed of drilling is a function of drilling strength of the rock. Many researchers have tried to correlate the speed of drilling with the strength properties of rock and compressive as well as tensile strength values have been found to give reasonable correlation." As the strength of rock drilled increases, speed decreases. As the Brazilian testing requires the least amount of core, this test was selected. Material Tested Broken Hill lode quartzite has been used in these tests. It is composed chiefly of quartz with varying amounts of sericite, pyrrhotite, chalcopyrite, galena, and garnet. The total porosity of this quartzite is about 11%.

Jan 1, 1973

By Thomas S. Nye

Mineral exploration in the United States relies heavily on theoretical geologic concepts and indirect methods such as geophysics and geochemical prospecting, as there are few exposed areas of mineralization which have not already been explored. In Mexico, ore grade samples can be cut at the surface on vein, replacement, and disseminated types of deposits in many areas. The problem is not in finding a mineralized area but in deciding which mineralized area can be explored and developed at the least risk and cost, with the greatest profit potential within the framework of Mexican mineral economics and that nation's government policies. Socio-economic Posture Mexico, prior to World War II, had suffered from more than one hundred years of intermittent wars and exploitation by internal and foreign elements. Consequently, the basic facilities which today's society takes for granted were scarce or non-existent in most of the country. Travel was largely a matter of negotiating poor dirt roads, riding horseback or walking. Relatively few people were literate and medical facilities were luxuries for the wealthy. Mexico's leaders were, however, determined to improve the lot of their people, within a system of private enterprise and personal freedom. Long-range programs initiated at about the time of World War II to provide infrastructure-education, health and welfare, transportation, power, water, communication-are now established fully or in part for most of the country and are being continually expanded.

Jan 12, 1972

By Charles Hawes

WHEN sulfur is encountered in objectionable amounts, it is regarded as the most trouble-some element for the mine operator to control. It exists in two conditions in iron ores, as sulfide in iron pyrites and as sulfate in gypsum and barite. The sulfate radical (SO,) may also be linked to one or more of the several other elements found in the iron ore compound. The only dependable method for the de-termination of sulfur, particularly when found in the insoluble residue, has been the so-called fusion method. This is a long and tedious process involving several hours for its completion. In looking for a more rapid method which would be .applicable to all iron ores, the writer investigated the work of M. Groger1 who in 1881 showed that by heating pyrite with iron out of contact with air, the pyrite is reduced to iron sulfide and from the latter all of the sulfur will be given off as hydrogen sulfide gas on treat-ment with hydrochloric acid. FeS2 + Fe = 2 FeS FeS + 2 HCl = FeC12 + H2S In 1891 F. P. Treadwell2 not only confirmed the results of M. Groger but also found that iron powder would reduce to sulfide the sulfate radical of any substance, including barite, if not found in excessive quantities. The writer found this to be true and developed a method, in cooperation with F. J. Baker, chief chemist, mining department, of the Cleveland-Cliffs Iron Co., Ishpeming, Mich., for the determination of sulfur in iron ores which is not only very rapid but also accurate. Pure iron ore powder, reduced by hydrogen, gave good results but was found to be very slow in reacting. A high silicon iron with a low sulfur content of 0.012 per cent was found to be. much more active than the pure iron and gave excellent results.

Jan 11, 1927

By W. A. Tiller, W. C. Johnston

A theoretical analysis of alloy solidification in which the effective partition coefficient, k, of the solute is allowed to vary as a function of interface position is performed. A variety of solute distm'butions in the solid is predicted depending upon the functional dependence of k with interface position. Conversely, the variation of k with interface position required to produce a particular solute distributzon in the solid can be calculated. These preciictions have been tested by controlling the width of the momentum boundary layer in the liquid as a function of interface position with a rotating mugnetic field. One of the objects of controlled solidification is to utilize the freezing process for the preparation of crystals of specific materials containing a predetermined distribution of solutes. For example, a thermoelectric power generation material may exhibit a figure of merit, 2,' as a function of temperature, T, and solute concentration, C, as illustrated in Fig. 1. If we wish to use this material in a device between the temperature limits T1 to T2 a significantly greater efficiency will result from the device if the thermoelectric element illustrated in Fig. 1 consists of a range of solute concentrations appropriately located with respect to the temperature distribution rather than using a sample of constant solute concentration. For this reason and many others2 we are interested in programming and controlling the solute distribution in a single crystal

Jan 1, 1962

By G. L. Craig

COPPER containing a small amount of arsenic has been used extensively abroad, and a number of reports, particularly those by English workers, have indicated that such copper is better suited for certain uses than high-conductivity copper. Inasmuch as a large percentage of the copper fabricated is used for nonelectrical purposes where high conductivity is not at all essential, it has been suggested that arsenical copper might be at least as suitable as high-conductivity copper for many purposes. An investigation spon-sored by the Calumet & Hecla Consolidated Copper Co. at Battelle Memorial Institute was therefore undertaken with the object of determin-ing the effect of small amounts of arsenic (up to 0.75 per cent) on the properties of copper. In this work the effect of arsenic on the basic properties of tough-pitch and of phosphorized copper have been critically studied and many data collected from laboratory experiments which have been supplemented by mill-scale tests. The results of these tests, with coppers of the type referred to, in the annealed condition and after various degrees of reduction, show that the basic properties of copper are not greatly affected by small amounts of arsenic, an increase in strength being observed with increasing arsenic with no corresponding decrease in ductility. It is well known that the evaluation of material for plastic deforma-tion, on the basis of laboratory tests, may not be directly comparable with its performance in commercial operations. In order, therefore, to substantiate the data obtained at the Institute, the cooperation of the Wolverine Tube Co. was obtained for a series of production tests on the fabrication characteristics of phosphorized arsenical copper in the manu-facture of seamless copper tubing. In these tests the behavior of the arsenical coppers was carefully observed in comparison with that of representative types of phosphorized arsenic-free copper, which were fabricated under the same conditions.

Jan 1, 1933

By D. R. Spink, D. N. Okuhara

Two reagents have been proposed for the commercial extraction of copper from leach liquors, namely LIX64N produced by General Mills Chemicals, Inc. and Kelex 120 produced by Ashland Chemical Company. Each of these reagents consists of an active extractant and an additive. In the LIX system, the additive improves the kinetics of the extraction reaction whereas for the Kelex system, the additive acts primarily as a third phase inhibitor. Equilibrium and kinetic studies have been conducted with both systems. In general, the Kelex system effectively extracts copper at a lower pH than LIX64N; furthermore, the rate of extraction with Kelex is considerably faster than with LIX which indicates that systems employing the Kelex extractants might also be able to employ agitated columns rather, than mixer- settlers which are absolutely necessary for effective extraction with the LIX reagents.

Jan 1, 1973

By S. R. Elliott

THE Spies mine is located in the eastern half of the northwest quarter of section 24-43-35, near the village of Iron River, Mich., and is operated by The Cleveland-Cliffs Iron Co. Speaking generally, the jasper hanging walls of most of the deposits in the Iron River district dip at a steep angle and are exceedingly strong, standing without caving, even after mining has been continued for years and after large excavations have been made. The ore is fairly hard and tough and contains no slippage faces. It occurs in large masses, which are often egg shape, with the smaller end down, and can be mined in, open stopes without the use of timber. The common system employed in the district is the shrinkage stope, or some modification of it. The Spies system was developed to utilize the advantages of the open-stope method and to avoid the disadvantages of the shrinkage stope. The Spies shaft was sunk to such a depth that the bottom, or third level, was in rock at a short distance below the bottom of the orebody, the shape and extent of which had been previously determined by diamond drilling. This is shown in plan and by the ore contours at the first, second, and third levels in Fig. 1, and in section in Figs. 2 to 7. In order to provide the necessary mills and raises, three parallel crosscuts were driven on 25 ft. centers on the bottom level. Drifts on the second and first levels were driven to the orebody and followed the foot wall in a southerly direction to the end of the ore. In crosscut 3, Fig. 1, raises 30, 40, 50, and 60 were carried up on the foot wall and holed into the second level, and were ultimately carried up and holed into the first level. These foot-wall raises carry the pipes and ladders, provide a means of ventilation, and furnish safe communication to all working places in the stope.

Jan 3, 1922

By E. P. Bucklen, L. J. Prelaz, J. R. Lucas

Today, the future of the coal industry is extremely bright because coal can be produced at a cost which makes it competitive with other energy sources. However, the industry has been forewarned that further cost reductions must be made if it expects to remain a serious contender in the growing energy market. Surface as well as underground operations must be improved. The very same elements which affected production a few years ago still exist today and will continue to be present in the future. Improvements in production mining equipment, mining methods and auxiliary equipment have resulted in reduced costs over the past few years. Efforts must be continued toward further reducing costs in areas which have been previously improved and new areas should be investigated for possible improvements. Therefore, new techniques must be developed which will enable the industry to augment its current efforts in reducing the cost of mining. The logical place to begin evaluating the factors affecting production and cost is in the immediate face area where a substantial part of the total cost of mining is incurred. The coal industry stands to gain much through the development of new techniques for analyzing the numerous variables affecting production and by establishing methods for eliminating or minimizing the adverse effect of those variables which can be controlled. Intuition and trial-and-error methods have been the standard means used to resolve many of the factors which influence production. As a result, many elements are overlooked or ignored because their effects on production are not pronounced and cannot be readily resolved.

Jan 3, 1965

By Mark Malamphy

DURING the latter part of the year 1932, the Servico Geologico e Mineralogico do Brasil ordered four magnetic field balances with tem-perature-compensated magnetic systems and a photographic recording apparatus for the registration of the diurnal variation. These instru-ments were delivered during the early part of the year 1933 and a short time later were taken to Santa Catherina for use in the field. Before the field work was begun, a series of experiments was carried out to determine the behavior of these new instruments under existing field conditions. The recording instruments were mounted in an under-ground chamber and their sensitivities checked by means of a Helmholtz coil. The field instruments were then mounted at fixed stations and readings were taken to determine the diurnal variation and compare it with the photographic records. The data obtained with the horizontal field balances were concordant but that obtained with the vertical component instruments showed a considerable divergence. This divergence was of such a magnitude that it was necessary to spend considerable time in determining its cause and finding a means of improving the functioning of the instruments. This paper presents the results of our observations on these systems and the conclusions at which we arrived; also the means we took to partly elimi-nate the difficulty until new systems could be ordered from Germany.

Jan 1, 1935

By William H. Pettee

A few weeks ago the Institute lost, by death, from its list of members one who in recent years, by frequent attendance at meetings, by the preparation of papers, and in many other ways, had shown a warm interest in Institute affairs; who had an extensive acquaintance among his fellow-members, and whose memory it is fitting to perpetuate by a permanent record in the volumes of our Transactions. Dr. Byron William Cheever, acting Professor of Metallurgy in the University of Michigan, died at his home in Ann Arbor, on the 6th of March, 1888. He was born September 17th, 1841, in Ellisburg, Jefferson County, New York. In 1844, the family moved to Geneva, Illinois, and thence, in 1857, to Dundee, Michigan. Two years later, a third removal was made to Ann Arbor to take advantage of the educational facilities there offered; and in 1859 the subject of this sketch, with his two brothers, entered the University of Michigan. In 1863, he took the degree of Bachelor of Arts. After a year or two of business life, he entered the medical department of the University, and graduated as Doctor of Medicine in 1867. A taste for scientific work had been developed in him in early life; and, even while carrying on undergraduate and medical studies, his proficiency in chemistry found recognition in his occasional employment as assistant in the University laboratory. The interval between the close of his course in Arts and the commencement of his course in Medicine was also devoted to chemical work, partly in the city of Philadelphia, and partly in the West Indies, where he was employed in the service of a commercial company engaged in the guano trade. Dr. Cheever never took up regular practice as a physician. After receiving his medical diploma he went again to Philadelphia, and for about two years was employed as an analytical and consulting chemist in that city. A favorable opportunity occurring for work in the Rocky Mountain mining region, he left Philadelphia and

Jan 1, 1888

By Walter P. Jenney

In the limestone area of Tintic and other mining districts of the Great Basin region of Utah, it has been observed that surface-outcrops of ore occur but seldom, and are mainly confilled to points of relatively low elevation, where the veins cross some basin or ravine. Nowhere does a considerable body of ore outcrop on the tops or high up on the slopes of the hills. Mining operations, on the other hand, have shown that large and continuous ore-deposits frequently occur in depth in the limestone, beneath large masses of barren rock. Such orebodies, when followed upward in the lodes, are found to terminate at well-defined levels, without reaching the surface. Yet the minerals-bearing fissures themselves extend above the top of the ore, being often traceable, though barren of all valuable minerals, for hundreds of feet above the stopes in the mines, and even observable in outcrops at the surface. This abrupt cessation of the ore at a uniform horizon does not appear to be connected with any change in the countryrock adjacent to the lodes. The strata above and below this horizon seem to be in every way equally favorable to ore-deposition. Explorations above it have developed an open-fissured country, barren not only of ore, but also of indications that minerals bearing gold, silver, lead or copper were ever deposited in the strata at that elevation. The height reached by the ore, while usually constant throughout the length of a given lode, may vary in particular sections, from the operation of local causes. Each lode in a district has its own distinct horizon, above which the oredeposits do not extend. Where the ore-bodies are continuous

Jan 1, 1903

By Ellen H. Richards

The water-supply of a country may be considered from three points of view: (1) its abundance and availability for agricultural purposes; (2) its chemical properties in their relation to manufacturing purposes; and (3) its quality and quantity as affecting domestic consumption. This paper concerns only those characteristics which may affect manufacturing and domestic uses. The so-called sanitary analyses deal not only with the common mineral elements found in water, but with organic matter and with those substances which, by their presence, indicate changes taking place through the agency of living organisms. Since these living organisms are frequently accompanied by others, capable, as are believe, of causing disease, the products of their action are looked upon with suspicion even when, as in the case of nitrates, that action may have taken place at a time long past. Therefore, upon the quality of the water-supply depends much of the history of a country, when rightly read, as well as much of its promise for the future. Thus, the hardness," or content of calcium and magnesium salts, gives a means of distinguishing at once between the waters traversing only igneous or other siliceous rocks and those coming from calcareous deposits. The presence of decomposing organic matter and intermediate products betrays a use of the water as the public carrier of refuse, which renders doubtful its fitness for domestic supply. In certain regions, one of the most valuable historical records is made by the relative amount of chlorine in the different waters. In the absence of rock-deposits carrying salt,, the chlorine present in rain and snow, and hence in mountainstreams and springs, appears to be derived from the air-borne, finely divided salt spray resulting from the beating of the ocean waves on the coast. If this be true, then the amount of chlorine found in a given water not contaminated with chlorides

Jan 1, 1902

By Luther W. Lennox

During the last few years, one of the great problems in the milling of all ores has been that of grinding. This subject involves not merely the cost of the operation, but also the selection of the proper degree and character of grinding to yield the best metallurgical results on the given ore. Considering the diversity of machinery, one is led to wonder at the variety of grinding methods employed, even when realizing that metallurgy demands varying products. In an attempt to investigate the relative grinding resistances of a number of ores now being milled in this country and Alaska, the manage-mxitofthe Portland mills requested Samples of average mill-run of ore from various companies. The request met with a ready response, indicating the desire of all operators to gain information on the subject. The difficulties involved in this investigation were numerous, lack of time for outside problems during this strenuous period being a serious one. Also, we were unable, in the time, to obtain a correct 150-mesh screen; in the screen analyses tabulated and plotted herewith, the 150-mesh screen was used merely to protect the 200-mesh screen, not to ascertain points on the curves. The experimental grinder was a small iron tube-mill, 8 by 121/2 in., in which was placed a definite number (74) and weight (3450 gm.) of 3/4-in. steel balls, 1 Ib. water and 1 Ib. ore. To obtain uniform conditions, each ore was first crushed and screened, and from the sized products a "standard feed" was artificially prepared, the same standard being adopted for all tests in that particular series. The prepared feed was

Jan 1, 1920

By J. Marvin Weller, M. King Hubbert

Preliminary investigations were undertaken with a Megger Ground Tester in 1931 by Hubbert to determine whether the faults in Hardin County, Illinois, could be located by earth-resistivity surveys. The results of these investigations, which were in part presented before this Institute in 1932,1 were sufficiently promising to warrant a more extensive field program in the same general area the following summer. During the second season an apparatus of the Gish-Rooney type was employed because of its greater sensitivity and to avoid the troublesome correction for resistance of potential electrodes necessitated by the use of a Megger instrument. The discussion of earth-resistivity traverses which constitute the main part of this paper is based entirely upon the results of the second season's work. All of the traverses were made with a constant electrode spacing of a equal to 100 ft., and the four-electrode technique was employed. Successive stations in these traverses were spaced at intervals of 100 ft. and the line of electrodes was carried parallel to the line of traverse. The graphs of resistivity profiles presented here (Figs. 1 to 3) are plotted with resistivities in ohm-centimeters as ordinates and with distance divided into stations at 100-ft. intervals as abscissas. After the traverses were run by Hubbert the results were computed, the profiles plotted, and tentative interpretations were made by him. These curves and interpretations were then taken into the field by Wellcr, who made a careful geological examination along the lines of traverse for the purpose of checking and supplementing Hubbert's interpretations. Weller then constructed a geologic cross-section extending along the line of each traverse. The accompanying diagrams graphically illustrate the correlation that can be made between earth resistivity and geology in this area.

Jan 1, 1934

By Charles Waidner

IN response to many urgent requests for a concrete realization of a series of standard temperatures that would be available to any one anywhere for the standardization of pyrometers and the reproduction of the standard scale of temperature for use in laboratories and industrial works, the Bureau, in 1916, made arrangements with several manufacturers to prepare a series of- pure metals that could best serve this purpose. After the necessary preliminary work of chemical analysis, as a check on the purity, together with exact determinations of melting or freezing points, the Bureau began, in 1917, the issuing of melting -point standards of tin, zinc, aluminum, and copper. At the outset, it was decided to secure metals of the highest purity and of American manufacture, and this was accomplished in a more satisfactory manner than anticipated. In the preparation of these temperature standards, the Bureau has had the hearty cooperation of several American companies, which have succeeded in producing metals highly satisfactory for the purpose and of as high a state of purity as could have been obtained anywhere. Each company that undertook the responsibility of furnishing a metal for this series of standards exercised most painstaking care to produce the best possible product as to purity and uniformity. A representative of the Bureau witnessed the actual preparation of each metal. The 300 and 400-lb. (136 and 181-kg.) samples making up the first series were all used up, with the exception of the aluminum, early in 1919. The Bureau has taken steps to replenish its stocks of metals serving as pyrometric standards and to the list has been added lead. The copper and lead are being ordered this time in 1-ton lots and the zinc and tin in 300-lb. (136 kg.) lots as before. The wide dissemination of these samples will be appreciated when it is noted that the metals are distributed by the Bureau inn quantities of 50 cu. cm. each, at $2 a sample and accompanied by a certificate which gives the melting point as determined by samples from the same lot. The manufacture and detailed description of chemical analyses, physical measurements, and precautions in use of these pyrometric standards, are described in detail in the Bureau Circulcar No., 66.

Jan 8, 1919

By J. M. Davey

Lead-zinc sulphide ores at Mount Isa are currently treated at the rate of 180,000 long tons per 28 day period in the No. 2 Concentrator of Mount Isa Mines Limited. Prior to June 1966 lead-zinc ore was treated in part of the No. 1 Concentrator up to a rate of 70,000 long tons per period. Since 1955, two major changes in ore type being processed have occurred. Because of these changes, problems arising from treatment of the ore have altered and during the period several major changes in practice have been advocated and experimentally tested. Most of these flow sheets were developed with a view to overcoming one major problem in the ore. These were invariably abandoned as the Mount Isa lead-zinc ore contains a number of equally major problems all of which must be overcome in the treatment process. MINERALOGY The orebodies are situated in the Mount Isa Shale Group which is Proterozoic in age (Carpentarian System). The sediments consist dominantly of fine grained dolomitic, quartzo-feldspathic shales and siltstones. Specifically, the Mount Isa orebodies lie in the Urquhart shale formation which is characterised by sediments of high albite and orthoclase content denoting a large volcanic component. The Urquhart shales are approximately 3,500 feet thick and extend at least north and south of Mount Isa for 20 miles in each direction. In the area of the silver-lead-zinc orebodies the Urquhart shales are highly pyritic and have a relatively high carbon content. The

Jan 1, 1970

By Enrique Touceda

As IN the case of steel and the non-ferrous alloys in general, the use of the microscope in connection with the manufacture of malleable cast iron has proved of inestimable value to the industry. Had its use not been invoked, many facts either would not be known at all or, if suspected, would be confined to the realms of conjecture. No fairer statement could be made than that the start of real progress in the industry was coincident with the application of metallography to the product, though the full significance of this statement can hardly be appreciated except by those who not only are conversant with conditions as they existed at the time referred to, but are familiar with the character of works' practice at the present time. A few years ago, about the only test made to ascertain the physical properties of the product, t except in the case of certain plants, was the bending of a casting to destruction, not only with the object of discovering whether or not the metal was ductile, but for the purpose of inspecting the fracture. The characteristics of the fracture, if correctly interpreted, were known to be of value in locating the trouble in, castings that were inferior. In general, it was found that if a casting of medium or heavy section would bend through a wide angle before failure took place, the fracture in the majority of cases would have a black velvety appearance; while if it was held at different angles to the direction of the rays of light, it would show a change of color and an iridescent sheen. But an inferior air-furnace heat or anneal might yield castings which, if thin and consequently largely decarburized, could be bent double on themselves and still not possess the fracture described. If, on the other hand, a casting broke short, its fracture might have one of a great many different color and structural peculiarities. Depending on the cause of the trouble, such castings might have any of the fracture characteristics, of which the following is but a partial list.

Jan 2, 1920