Search Documents

By Reginald S. Dean

THE widespread occurrence of manganese in low grade oxide and carbonate ores not amenable to mechanical concentration has led to extensive investigations of hydrometallurgical methods for producing a pure manganese compound suitable for further treatment. Manganese carbonate is the preferable compound. This product when fully crystalline and of not too fine crystal size is easily filtrable and stable in air. It can be converted to other compounds such as the oxides by heating in air or can be reacted with acids for producing salts. A useful hydrometallurgical process must produce relatively concentrated solutions that can be purified easily, reagents must be cyclically used, and heat requirements must be small. Neither the ammonium sulphate nor sulphur dioxide leaching processes that have been tested extensively fulfill these 'requirements. Other hereto-fore proposed processes have obvious limitations and have not been tried on a large scale. The present process is based on the discovery by the writer of a new group of aqueous manganese-ammonia complex solutions highly concentrated in ammonia, which permit rapid solution of manganous oxide to concentrations of 80 to 100 g Mn per liter and from which a fully crystalline, easily filterable manganese carbonate is precipitated by the addition of carbon dioxide and partial ammonia removal. Although the process may be carried out with many ammonium salts, commercial advantages dictate the use of ammonium carbamate, which is obtained when CO2 is passed into concentrated aqueous solutions of ammonia. If the carbamate is used, the only reagents, ammonia and C02, are volatile and may therefore be recovered from solutions and residues by heating, thus eliminating washing and extensive evaporation. Impurities are controlled easily as most metal oxides are either insoluble in the lixiviant or fail to precipitate with the manganese carbonate. Others are controlled by sulphide addition. The process has been tested extensively on a small scale on a wide variety of ores; including Three Kids, Artillery Peak, Cuyuna, and Chamberlain; as repre-

Jan 1, 1952

By Carle Hayward

THIS work was first undertaken in the metallurgical laboratory of the Massachusetts Institute of Technology in 1907 by L. A. Dickinson, E. Phelps, and V. S. Rood, under the author's direction. They attempted to determine the diagram for the system Cu2S-NiS, but several inexplicable results were obtained. The following year, P. H. Mayer with Mr. Dickinson carried, on some experiments with nickel sulphide and found that the molten material slowly lost sulphur until it reached a composition corresponding to the compound Ni3S2, established by Bornemann.1 At this point the composition remained stable. The freezing points of the mixtures gradually fell off with the loss of sulphur. Since the above facts seemed to explain the erratic results obtained in the first experiments, Mr. Mayer with F. Jaeger attempted in 1910 to establish a correct equilibrium diagram for the Cu2S-Ni3S2 series. They prepared pure Cu2S and Ni3S2 and determined the cooling curves for various mixtures. The fusions were made in a platinum resistance furnace and the temperatures were measured with a platinum-iridium thermocouple connected with a Sullivan galvanometer. The curve was established for mixtures containing more than 40 per cent. Cu2S, but they were unable to determine certainly the direction of the curve beyond that point. Nothing further was attempted with this series until the present year, when the work was carried to a successful conclusion with the assistance of A. Butts, Jr., and E. H. Weil. The results of this work are given in the following pages.

Jan 1, 1914

By James Norman, O. C. Ralston, John Dasher

Most mineral products are used in the finely divided state, but some are sold in larger sizes. Coal, gravel, metallurgical fluorspar, phosphate rock, hematite, chro-mite, and other products are sold in sizes coarser than can be treated by many mineral-dressing methods. Gravity separation of coarser sizes by log washing and jigging is probably as ancient as any process now in use. The performance of jigs on a feed with sufficient difference in density of the minerals is excellent, but many families of minerals are too similar in density to be separated effectively by this method. The use of heavy suspensions of fine solids to separate coarse coal from bone and slate has been in use for some years. This separation by sink-and-float was limited until recently to light minerals. Development of galena and ferrosilicon as suspension media, by Minerals Beneficia-tion, Inc., at Mascot, Tenn., Pitcher, Okla., and Crosby, Minn., under patents granted during and since 1938, has permitted excellent results to be obtained on minerals of very similar densities up to 3.3. This process has been put In the hands of American Cyanamid Co. for exploitation, and further research now in progress may increase the density of suspension obtainable so that separations at a density of 4.0 may be practicable before this is published. The Huntington-Heberlein dense-medium process, developed in England, is also being commercialized in the United States by Sink and Float Corporation. Du Pont has developed a sink-and-float separation using halogenated hydrocarbons as parting liquids; at this writing, the method is used commercially only on coal but has been successful in the pilot plant on many other minerals using tetrabrom-ethane at densities up to 2.95. While these processes were being developed to extend the range of separation by difference in density to the coarser sizes, the Bureau of Mines was engaged in developing a process that will extend the range of separation by difference in wettability up to 2-in. size. War work has pushed aside its further development indefinitely. The results are published here with the hope that some use may be suggested that will justify post-war development, and so that readers that may be able to make immediate use of the scheme may have the information. Earlier Work It has been known since the time of Herodotus (B.C. 484(?)-425) that water-repellent particles will adhere to sticky surfaces. That early historian reports the recovery of gold from the mud of a lake

Jan 1, 1943

By V. H. Wilhelm

Drilling activity in California during 1939 decreased approximately 15 per cent from that of the previous year. New reserve discoveries were the lowest in many years, but extensions, development of deeper sands, and reappraisals, indicated enough new potential to more than equal 1939 withdrawals of about 223,644,000 barrels. On June 1 a new uniform method of allocation was adopted, which had the immediate effect of reducing production, so that approximately 6,000,000 bbl. of crude were withdrawn from storage during the year. Market demand averaged 628,845 bbl. per day as compared with a daily production of 612,945 barrels. The rate of drilling was slow during the first five months because of the unfavorable storage situation. Subsequent to the adoption of the new uniform method of allocation on June 1, drilling was speeded up and continued at a rapid rate throughout the remainder of the year. As a result of prospecting, four new fields were discovered and seven fields were measurably extended. All of the new discoveries were made in the San Joaquin Valley. Statistics of production and development arc given in Fig. 1 and Tables 1 to 3. New Discoveries Coalinga-Northeast.—The Amerada Petroleum Corporation discovered a second Eocene shore-line field north of the Coalinga Nose when it brought in well S.P.L. 7-17 in sec. 17-19-16, flowing 4230 bbl. of 32.4" gravity oil and 14,200,000 cu. ft. of gas at a depth of 8237 ft., from the "Gatchell" sand of Eocene age. This field, 2 miles north of the Coalinga Nose field, is considered to be a separate structure because it has a gas cap and a lower water table. The structure is a broad, gentle anticlinal nose probably separated from the southerly Coalinga Nose field by a shallow syncline. Production is sealed updip by the pinching out of oil sands. The average sand thickness is approximately 200 ft., the top 75 ft. containing mainly gas. The sand has an average permeability of 1000 millidarcys and an average porosity of 25 per cent. The productivc area of the field is estimated to be between 1200 and 1500 acres.

Jan 1, 1940

By M. J. Taylor

A common method of classifying non-water- impounding mine waste structures is necessary to facilitate professional comnunications within the industry and between representatives of industry and government. Camnon classifications can a1 so he1 p quickly create and maintain a mental picture of the structures being discussed. Three categories for classification presented in this paper include: (1) configuration and location with respect to existing topography. (2) material characteristics of waste, and (3) environmental sensitivity or characteristic; of the disposal area. Configuration and location classification involve terminologies typically utilized for waste dumps over the past several years. General classification categories for non-impounding structures include: (a) valley-fill, (b) cross-valley, (c) side-hill, (d) ridge, and (e) heaped. Material characteristics can govern the location, engineering details, and environmental sensitivity of the waste structure. Material classification includes: (a) hazardous, (b) non-hazardous, (c) inert, (d) fugitive dust susceptible and (e) leachate susceptible. A1 though many characteristics are potentially applicable, this paper will focus on the categories mentioned above. Environmental sensitivity of a waste structure encompasses many objective and subjective evaluations plus many multi-disciplinary considerations. Environmental sensitivity incorporates numerous factors in addition to those highlighted in configuration and location, and material characteristic classifications. A few examples of how this categorization can govern the engineering design and location of waste dumps are provided in this paper. In addition to the verbal descriptions of classifications, a simplified version of the combined classifications with an alphanumeric format and its methodology is discussed in this paper. Surface water controls often govern the classification or vice versa. In order to maintain a non- impounding status, water must be prevented from collecting behind the structures. Depending on material characteristics, water inflow to or over the site can cause significant environmental or human consequences. Finally, the access of water to the waste dumps can play a large role in the degree of environmental sensitivity to the site. This paper provides a framework in which to discuss the other aspects of this conference and also provides insights as to how the framework is based on actual practice.

Jan 1, 1985

By H. J. Rose

Graphic methods have long been used to advantage in dealing with diverse phases of fuel technology and research. Not only are graphs convenient for presenting data and making calculations, but they are invaluable for deriving generalizations from a mass of data. This is particularly true when relationships are obscure and numerical correlation is poor. This paper describes a new form of graph, the Multibasic Coal Chart, which has been developed to facilitate the study and comparison of coals of all ranks from peat to anthracite on any moisture and purity basis. This type of chart is of unique value for coal classification purposes, since it permits a direct visual comparison of the results obtained when coals are classified by the various systems which have been proposed. Coals are highly variable in character as a result of wide differenees in original vegetal ingredients, degree of metamorphism, and nature and amount of associated impurities. For nearly 100 years, attempts have been made to devise a satisfactory method of classification, and many tables, formulas, ratios and graphs have been suggested. Many of the suggested systems possess considerable merit and have found a limited use, thus promoting a better understanding of coal. However, objections have been raised against each system, and none has received general adoption. When the various systems of classification are compared, it is found that there is an apparently almost hopeless confusion due to: 1. Serious lack of agreement as to the proper moisture and purity basis on which to classify coal. More than ten different bases have been proposed, each of which requires complete recalculat.ion of the analysis data used. 2. Lack of agreement as to what chemical and physical properties are most important and best to use for classification purposes. There is too little knowledge of the degree to which these properties can be correlated.

Jan 1, 1930

By G. F. Huff, G. R. Bailey, J. H. Richards

An improved bomb-sampling technique for obtaining samples for oxygen analysis from liquid steel is described. Analyses of samples taken from open-hearth furnaces by the improved method show sufficient agreement with laboratory data to indicate the accuracy of the method is better than that of other existing sampling methods. THE bomb-sampling method of determining the oxygen content of a liquid-steel bath was studied by obtaining and analyzing more than 200 samples from normal open-hearth heats. Of these samples, about 60 were obtained with a bomb of conventional design;' the remainder were taken with a somewhat modified bomb designed to give greater protection against slag contamination. In the new device, the contacting faces of the cast-iron mold halves are machined so that they fit closely; the opening at the top of the bomb is covered with a thin steel cap; and the top of the bomb is further covered with a wood block held in place by heavy steel wire. After the bomb has passed through the slag layer and has entered the steel bath, the wire melts and the wood block floats to the surface. Thereafter, the steel melts through the thin cap and flows into the bomb cavity where it is deoxidized with aluminum wire. An assembled bomb, ready for sampling, is shown in Fig. 1. To standardize sampling procedure, the samples were usually taken through the center door and at the bottom of the furnace; that is, the bomb was on the bottom when the metal cap melted. After each addition to the furnace, at least 20 min elapsed before a sample was taken. The oxygen contents of all the samples were determined by using the vacuum-fusion method, two or more specimens from each sample being analyzed. The specimens were cubes of metal cut from a region in the interior of the bomb sample, as shown in Fig. 2. Drillings for carbon analysis were obtained immediately above the oxygen-analysis region. Reproducibility of Results In determining the reproducibility of the results obtained with the modified bomb, the following four factors were studied: 1—variation in the oxygen concentration of duplicate specimens taken from a single sample; 2—variation in the oxygen concentration of duplicate samples taken in quick succession: 3—effect of the amount of aluminum wire

Jan 1, 1953

By G. C. Bateman

THE Workmen's Compensation Act of Ontario was passed in 1915 and Miners' Phthisis was added to the list of compensable industrial diseases in 1916. Under this provision of the Act only about two cases were compensated per year. In 1924, The Department of Public Health made a survey of miners in the four principal camps-Sudbury, Porcupine, Kirkland Lake and Cobalt--and the survey indicated that an alarming proportion of the men exposed to dust had silicosis in one or other of its several stages. A number of conferences were held between representatives of the Department of Mines, the Department of Public Health, the Compensation Board and the mine operators. The operators were advised that in the earliest stages of silicosis there was no physical disability and if men in that stage were removed from underground there would be little danger of permanent disability. They were further advised that if active steps were taken at once to compensate men that had some real disability and remove from the mines men in the early stages of silicosis, the first cost would be the greatest and thereafter their liability should decrease. As a result of this advice, and having at that time no reason to doubt the findings of the survey, the operators agreed to do all that was asked of them and cooperate with the Government in the steps believed necessary to meet the situation, and to provide compensation for the men affected. Amendments In 1926 Arrangements were made for the necessary amendments to the Mines Act and the Workmen's Compensation Act and these amendments were passed in 1926. The Amendment to the Mines Act provided that all underground employees must be the holders of certificates certifying that they were free from tuberculosis of the respiratory organs and further provided that the certificates must be renewed annually. The Government, however, at that time refused to adopt a form of certificate for applicants certifying as to their physical fitness for underground work. The Amendments to the Compensation Act defined both silicosis and

Jan 1, 1937

Christopher R. Corning was one of the ablest mining engineers and geologists in America and one whose name was well known also in Mexico, Cuba, South America and many European countries. He was educated at Zurich, Switzerland, and at the Bergakademie, Freiberg, where he was graduated in 1883 with the degrees of Markscheider and Bergingenieur. He continued his studies at Heidelberg until 1886, chiefly in chemistry, under Bunsen, and mineralogy and petrography under Rosenbusch. Although he received a Ph.D. in chemistry, he never used the title. During holidays of 1883-86, he traveled, seeing mines and studying geology in Spain, France, England, Italy, Germany, and Austria. In 1886, he returned to America and in 1887 he was in the Lake Superior iron ore country on the staff of John F. Stevens, then building the Duluth South Shore and Atlantic Railway. In 1889, Mr. Corning was at the Bunker Hill & Sullivan mines at Wardner, Idaho, with John Hays Hammond, and there met E. E. Olcott. Although Mr. Corning was not long connected with the Bunker Hill & Sullivan mines, he left the imprint of his ability and splendid personality upon the men and the property. That his friendship was cherished was manifested by the cordiality, hospitality and frequency of letters of good counsel and cheer. In 1897, Mr. Corning, with E. E. Olcott and Prof. Robert Peele of Columbia University, formed the firm of Olcott, Corning & Peele, consulting mining engineers. Pressure of university duties compelled Professor Peele to withdraw in 1904, and later Mr. Olcott was forced to retire by reason of other important business interests, but the friendship and high mutual regard of the three men continued undiminished. About 1902, Mr. Corning and Professor Peele translated into English Riemer's book on "Shaft Sinking under Difficult Conditions." Mr. Corning's knowledge of structural geology, mineralogy and ore deposits was extensive and accurate. He was a close and intelligent observer. When he became interested in a problem, no amount of trouble was too great in endeavoring to reach a satisfactory solution. He had professional experience in the West, notably in the Coeur d'Alenes, Mexico and South America, and several times was called on to attempt to straighten up mismanaged properties. In 1912, at the request of a large number of members, Mr. Corning headed the "Committee of FiveJ' that investigated the affairs of the American Institute of Mining Engineers and brought about beneficial changes in the organization and its policies. He was one of the organizers

Jan 1, 1924

By L. L. Foley, C. V. Millikan

The discovery of Bromide production in the Fitts field, shallow production in Jackson County of Southwestern Oklahoma, abundant production in the Edmond field, and discovery of many small pools in all parts of the state, were the events that made petroleum history in Oklahoma in 1934. Wildcatting was much more active, as evidenced by a number of new discoveries. There was no important development in the older fields. The rapid decline of the potential of the Oklahoma City field was an important feature of the history of the year. The accompanying tabulation of oil fields (Table 1) is not complete. Many of the early records of operators and pipe line companies are lost and it will be impossible to work up complete statistics for a number of the older fields. The table includes most of the important fields of the state and includes fields of a number of different types. It is hoped that a great many additional fields may be worked up for next year's report. Fitts Pool.—The Fitts pool, in Pontotoc County, was discovered in 1933. Before the middle of 1934, the Pennsylvanian sands yielded -some oil at depths ranging from 1400 to 2800 ft. The Hunton series (Siluro-Devonian) produced most of the oil with considerable gas. In July, 1934, a well in sec. 25, T.2N., R.6E. was completed in the Bromide (Ordovician " Wilcox ") with an initial production of about 300 bbl. a day. Less than a month later a second Bromide sand well was completed in sec. 30, T.2N., R.7E., which made over 200 bbl. an hour. This started an active drilling campaign, which was accelerated when some of the major companies paid good prices for adjacent acreage. At the end of the year, 23 wells had been completed and the rate of development was increasing rapidly. It is a major oil field. The Fitts pool opened a new geological province for oil production. The structure is a faulted anticline in a graben. The producing formation (Bromide) and the Arbuckle lime below it crop out about 2 miles south of present production. The Hunton lime crops out about 2½ miles north. The field is in a sharply folded and faulted area on the northeast side of the Arbuckle uplift. Heretofore, it was generally considered not favorable for oil production, although some gas had been found in various places. The play has extended east into the McAlester coal basin, and southeast toward the

Jan 1, 1935

By Duncan MacVichie

The iron fields described here are located in the Iron Springs and Pinto mining districts, Iron County, Utah. This region is in southwestern Utah, about 260 miles south from Salt Lake City, and is reached by the Los Angeles & Salt Lake railroad of the Union Pacific system. The iron fields lie at an elevation of 5500 to 7500 ft. above sea level, and are essentially desert in character. They are covered with a light growth of sage brush, piñon pine, and scattered cedar. Weather conditions are unusually favorable for all-year mining operations, the winters being mild with little or no snow; and the summers not excessively hot, the temperature rarely rising to 100 during the day, while the nights are invariably cool. The iron-ore bearing area extends from the Iron Springs district to the Iron Mountain mining district, being approximately 25 miles long in a northeast-southwest direction, and from 1 to 3 miles wide in a northwest-southeast direction. In the Iron Springs and Pinto mining districts, the ore occurs at various points around three sides of Granite Mountain and Iron Mountain. This is readily understood by reference to Figs. 1-4. These mountains are composed of andesite, which has been forced up through the surrounding sedimentary formation, in the form of laccoliths. An extensive report on the geology of these districts was made by Leith and Harder,' who state: The three dominating geological features of the district are three large andesite laccoliths which constitute the Three Peaks, Granite Mountain, and Iron Mountain; lying in a northeast-southwest line across the area in question. Three unconformable sedimentary series, aggregating 4000 ft. in thickness, outcrop in successive rings around these laccoliths, dipping outward asymmetrically, very steeply at the contact, less steeply farther away. Still farther from the laccoliths, lava-flows 2000 ft. thick rest in nearly horizontal attitudes on the tilted sedimentary rocks. These general relations are modified by faulting. All of the rock formations of the district are more or less covered on the middle and lower slopes by unconsolidated and partly consolidated erosion debris, both aqueous and subaerial, which spreads out on the lower ground to make the deserts.

Jan 1, 1927

By V. R. Garfias

. EVEN before the arrival of Cortes in 1519, the history of Mexico was closely linked to that of its mineral production; the mining activities of the Aztecs being thus described by Clavigero, one of the early historians: In the mountains of Anahuac there abound in veins all kinds of metals, and infinite variety of other fossiliferous products. The Aztecs obtained gold from the countries of the Cohuijques, of the Mixtecas, of the Zapotecas and from various other places. They gathered that precious metal usually in grain, from the sands of the rivers, keeping a certain portion for the crown. They obtained silver from the mines of Taxco, of Tzumpango and others; however, this metal was not as esteemed by them as by other neighboring nations. They had two kinds of copper; one hard, which they used instead of iron to make sickles; lances and all kinds of rural and military instru-ments and another, soft, with which they made kettles, goblets and other receptacles. This metal abounds mainly in the province of Zacatula and in that of Cohuijques, which at present is in the kingdom of Michoacan. They obtained tin from the mines of Taxco and lead from those of Izmiquilpan, located in the country of the Otomies. From the tin they made money, and the lead, we know they sold in the market places, but we ignore the uses to which they applied it. They also had mines of iron in Tlaxcala, in Taxco and in other places; but they either had not discovered them, or did not know how to make use of the metal they contained. In Chilapa there were mines of mercury, and in other places there were mines of sulphur, alum, vitriol, cinnabar, cohre and of a white earth which they esteemed highly. As regards mercury and vitriol, we do not know of what use (they were to them; the other metals they used in paintings and dyes. There were then great abundance of amber and asphalt-bitu-men of Judea-on the coast of the seas and many cities of that territory paid tribute of one and the other to the kingdom of Mexico. They mounted the amber in gold, and it was only used as ornament and display by them. With the asphalt they made certain perfumes.

Jan 1, 1937

By E. H. Crabtree

THE heavy-media separation plant at the Central mill of the Eagle-Picher Mining and Smelting Co., near Picher, Okla., was started in February 1939. Since that time twenty-four million tons of lead-zinc ore has been treated in the mill, of which approximately 70 pct has been treated by heavy-media separation. Until January 1945, galena concentrate from the flotation plant was used as the sink-float medium. At that time minus 100-mesh ferrosilicon was substituted for the galena, and its use has been continued. The purpose of this paper is to compare the operating results and the costs of operation of the two media. For the purpose of this comparison the period Jan. 1, 1943, to Jan. 29, 1945, has been taken to represent the operation using galena medium; the period Jan. 29, 1945, to Sept. 1, 1946, to represent the ferrosilicon medium. During the first of 'these periods about seven and one-half million tons was milled; during the latter, or ferrosilicon period, more than five million tons was milled. It is believed that these tonnages are large enough to give representative data. FLOWSHEET The Central mill has a capacity of 15,000 tons per day. Briefly, the treatment used consists of crushing the ore through 11/2-in. and wet-screening out the minus 3/16in. portion. The minus 1 1/2 plus 3/16in. washed product is treated by the heavy medium; the minus 3/16-in. product is deslimed and jigged. The heavy-media cone tailing is discarded and the cone .concentrate is recrushed and jigged for the production of a coarse lead concentrate. The cone concentrate, impoverished of lead, is then ground in ball mills and treated by differential flotation. The minus 3/16-in. jig product is similarly treated. HEAVY-MEDIA PLANT The heavy-media cone plant treating the minus 1 ½ plus 3/16-in. product consists of one open-top cone 20 ft in diameter by 20 ft deep, equipped with a central airlift. Concentrate is discharged from the top of the airlift to a 3 by 14-ft low-head Allis-Chalmers drainage screen. Medium drains back into the cone, from the first half of this screen. The last half of the screen is provided with washing sprays for further removal of medium. Cone tailing is similarly drained and washed. Undersize from the washing screen is thickened and then cleaned in the medium-cleaning plant. When galena was used as a medium, cleaning was done in Fagergren and Denver flotation machines. The ferrosilicon is cleaned in three 36-in. and one 24-in. Crockett magnetic separators. A flowsheet of the cone plant is shown in Fig 1.

Jan 1, 1947

By Fred H. Kan

The production of petroleum in Venezuela during 1931 was approximately 118,767,000 bbl., a decrease of 18,904,000 bbl., or 13.7 per cent, compared with the previous year. This is the first break in production, which has risen steadily since 1920, and is attributable to restriction of output and drilling operations, in harmony with lessened demand, rather than to any real decline in potential production. Venezuela ranked third among the world's producers, having lost second place to Russia. The Bolivar coastal fields, which were extended approximately 14 miles southward during the year, continued to supply most of the oil. La Concepcion, Los Manueles and Quiriquire all showed marked increases. A new field of light oil was discovered on the north coast near Puerto Cumarebo, State of Falcon. Exports declined 15.7 per cent, from 137,377,000 bbl. in 1930 to about 115,800,000 bbl. in 1931. Crude oil in storage at the end of the year amounted to 7,450,000 bbl., a decrease of 2,150,000 as compared with 1930. Tankage utilized is about 40 per cent of the available space. A drastic decline in drilling activity reduced the number of wells completed in producing areas from 401 in 1930 to 116 in 1931. Only three wells were drilled in the Lagunillas field proper, but, the amount of closed-in production and proven acreage gave assurance of a satisfactory potential output. Of the 1580 wells drilled to the close of 1931 in the producing areas of the Bolivar Coast, 631 were active and 853 were closed in; 96 had been abandoned. The status of the active wells at the end of 1931 was as follows: flowing, 331; pumping, 99; gas-air lift, 201. Producing wells closed in numbered 452; workovers, 8; totally inactive, 393. Lago Petroleum Corp. and Venezuela Gulf Oil Co. placed in operation the first units of their electric power plants, the former at Punta Gorda and the latter at Las Morochas, and are replacing steam power in their operations as rapidly as possible. Compressor stations were also installed for use in connection with air-gas lift operations. A considerable volume of gas was treated in gasoline extraction plants, the tail gas being recom-pressed and utilized together with natural high-pressure gas, for stimulation of production.

Jan 1, 1932

By G. Mempel, D. C. Yang, D. W. Fuerstenau

This paper describes details of the design and operation of a batch tumbling mill which has been used for a number of years in the laboratories at the University of California. In order that the energy expended for grinding can be measured accurately, this specially constructed laboratory mill has sensitive torque measuring apparatus. Torque measurements are given for a variety of conditions with this particular mill. In recent years, there have been numerous and fairly extensive investigations of grinding in tumbling mills reported in the literature. Most of these investigations have been carried out in mills with widely differing dimensions. As a result, comparison of results obtained from various investigations has been virtually impossible. If similar mills were used by different investigators, a considerable step forward would be taken in grinding research. A specially constructed laboratory mill with sensitive torque measuring apparatus has been used for a number of years in the laboratories of the University of California. The purpose of this paper is to describe details of the design and operation of this batch tumbling mill so that other researchers, who might be interested in obtaining data for intercomparison, could construct a similar device for their own research. Furthermore, since torque instrumentation is quite expensive, torque measurements are given for a variety of conditions with this particular mill so that those who may not wish to duplicate torque measuring apparatus can make reasonably accurate torque estimates merely by duplicating the loading conditions. It is not intended in this paper to present theoretical derivations of energy consumption in ball mills. This has been done e1sewhere.l-3 CONSTRUCTION OF THE MILL In order to eliminate rust problems with wet grinding, the mill and grinding media are made of stainless steel. The mill shell was rolled from 1/2-in. steel plate. The inside dimensions are 10-in. diam and 11-1/2-in. length, similar to the mill used by Charles.4 It is equipped with eight lifter bars (1/4-in. in height) whose dimensions are given in Fig. 1. The lifter bars have been bolted into the shell so they can be removed for experiments without lifter bars; however, all data presented here are for the mill with lifters. One end of the mill is fitted with two 1/2-in. diam removable plugs for filling the mill with liquid for wet grinding experiments. The mill is mounted on ball bearing rollers as can be seen in Fig. 2. The pillow block bearings are single-row self-aligning sealed ball bearings with 1-1/4 in. hole diam. The bearings supporting the mill shell are single row sealed ball bearings with

Jan 1, 1968

By Horace Knerr

The term. "high-yield-strength," used in the title of Dr. Gillett's paper (p. 40) is obviously relative. His discussion is limited to improved steels intended to compete with the low-cost, low-carbon, hot-rolled, sheet and plate steels of commerce made and used on a tonnage basis, without heat-treatment. In his list of about three dozen steels, only three have a yield strength of 70,000 lb. per sq. in., or over. Double such values are not uncommon in aircraft steels. Dr. Jeffries (p. 21) refers to "light-weight metals," obviously meaning strong alloys of low specific gravity; namely, aluminum alloys of the duralumin type and certain magnesium alloys. In a structural material, "lightness" is determined by two factors, strength and specific gravity. They must always be considered jointly. The basis of comparison is a strength-weight ratio, obtained by dividing the desired strength value, such as tensile strength, yield strength, or endurance limit, by weight per unit of volume, such as specific gravity or pounds per cubic inch1. For example, aluminum is a heavy metal, structurally, unless alloyed and heat-treated to give it high strength. When the strength of a structural metal is raised by heat-treatment or by cold-work, its specific gravity is not appreciably changed, but it is made lighter in direct proportion to the increase in strength because less of it will be required to carry the load. The lightness of the finished structure of adequate strength is the real point of interest. This structure must not only carry designed load, but "stand the gaff" of service, which includes the effects of accidental overload, fatigue, corrosion, loosening of joints, and so forth. Neither Dr. Gillett nor Dr. Jeffries mentions the true "lightest material of construction," which is alloy steel, tubular in form (Fig. 1), assembled by welding and heat-treated to a yield strength in excess of 150,000 lb. per sq. inch.

Jan 1, 1936

By V. H. Wilhelm

Drilling activity in California during 1939 decreased approximately 15 per cent from that of the previous year. New reserve discoveries were the lowest in many years, but extensions, development of deeper sands, and reappraisals, indicated enough new potential to more than equal 1939 withdrawals of about 223,644,000 barrels. On June 1 a new uniform method of allocation was adopted, which had the immediate effect of reducing production, so that approximately 6,000,000 bbl. of crude were withdrawn from storage during the year. Market demand averaged 628,845 bbl. per day as compared with a daily production of 612,945 barrels. The rate of drilling was slow during the first five months because of the unfavorable storage situation. Subsequent to the adoption of the new uniform method of allocation on June 1, drilling was speeded up and continued at a rapid rate throughout the remainder of the year. As a result of prospecting, four new fields were discovered and seven fields were measurably extended. All of the new discoveries were made in the San Joaquin Valley. Statistics of production and development arc given in Fig. 1 and Tables 1 to 3. New Discoveries Coalinga-Northeast.—The Amerada Petroleum Corporation discovered a second Eocene shore-line field north of the Coalinga Nose when it brought in well S.P.L. 7-17 in sec. 17-19-16, flowing 4230 bbl. of 32.4" gravity oil and 14,200,000 cu. ft. of gas at a depth of 8237 ft., from the "Gatchell" sand of Eocene age. This field, 2 miles north of the Coalinga Nose field, is considered to be a separate structure because it has a gas cap and a lower water table. The structure is a broad, gentle anticlinal nose probably separated from the southerly Coalinga Nose field by a shallow syncline. Production is sealed updip by the pinching out of oil sands. The average sand thickness is approximately 200 ft., the top 75 ft. containing mainly gas. The sand has an average permeability of 1000 millidarcys and an average porosity of 25 per cent. The productivc area of the field is estimated to be between 1200 and 1500 acres.

Jan 1, 1940

By J. F. McLaughlin

The installation of the Chance flotation system for the preparation of anthracite demonstrated the need for some means by which the specific gravity of the fluid mass in the separating cone could be determined with a fair degree of accuracy. The means used (with the original cones) was a set of wooden balls attached to ropes or chains, each with a different specific gravity. In the Northern Anthracite field, where the cones are generally operated with the specific gravity at 1.65, these gravity balls are provided with a range of 1.6, 1.65, 1.7 and 1.75. The operator of the cone from time to time would place one or more of these balls in the cone and estimate its specific gravity by the action of the balls. The margin of error with this system was very great, because there was the possibility that the test ball might be held in suspension and carried around by material floating beneath the surface of the cone in what is known as "island " formation—a formation resulting from a low sand line in the separating cone. The inaccuracy of this system of determination of specific gravity was indicated also by periodic tests of the final refuse bank, which showed excessive losses of coal to the refuse. Further evidence of the unsatisfactory operation of the cone was the uneven appearance of the market product, which caused spasmodic condemnation. Maintenance of Even Preparation With the critical market condition of today, it is essential that the preparation units operate consistently to maintain an even preparation. If a plant wishes to maintain a 1.65 specific gravity preparation, which means that all material of a specific gravity greater than 1.65 is classed as "reject," if the specific gravity of the fluid mass runs to 1.70, the market product will not be satisfactory; or if the specific gravity of the fluid mass is 1.60, the market product will be entirely satisfactory but the losses at the slate ends will be excessive. The desired specific gravity of the fluid mass in the Chance cone is maintained by agitating the sand within the separating cone by means

Jan 1, 1931

By Willard R. Jillson

Within the last ten years Kentucky has become celebrated for its low-sulfur bituminous coals. Prior to this time, many investigators had discnvered the abundance of this coal but the fact was unknown to the general public until the last extension of Kentucky's mountain railroads' was completed. The coals of. Kentucky are, broadly, separated into two geographic units—the eastern and the western coal fields. On a basis of their sulfur content these coal fields fall into three units, which are indicated on the accompanying map, by numbers, 1, 2, and 3. The area marked 1, the very southeastern part of the state, shows the lowest sulfur, all coals being averaged. In this field the maximum is 1.04 per cent. and the minimum as low as 0.68 per cent.—both averages and not individual analyses, which would of course show much greater variation. Included in this group are the following counties: Lawrence, 0.87 per cent.; Martin, 0.75 per cent.; Johnson, 0.73 per cent.; Magoffin, 0.87 per cent.; Floyd, 0.88 per cent.; Pike, 0.68 per cent.; Knott, 1.04 per cent.; Perry, 0.77 per cent.; Letcher, 0.80 per cent.; Leslie, 0.70 per cent.; Harlan, 0.79 per cent.; Knox, 0.86 per cent.; and Bell, 0.92 per cent. The total average sulfur content for these thirteen counties is 0.82 per cent. Bordering the restricted low-sulfur field of eastern Kentucky is the No. 2 belt (slightly darker), 'which is commonly known as the western border of the eastern coal field. Here the maximum sulfur is 2.91 per cent. and the minimum 1.05 per cent. Again these are averages and not individual analyses. The counties in this group are: Greenup, 2.60 per • cent.; Boyd, 1.67 per cent.; Carter, 1.07 per cent.; Morgan, 1.40 per cent.; Wolfe, 1.83 per cent.; Lee, 2.93 per cent.; Breathitt, 1.85 per cent.; Owsley, 1.09 per cent.; Jackson, 1.06 per cent.; Rockcastle, 2.30 per cent.; Clay, 1.09 per cent.; Laurel, 1.08 per cent.; Pulaski, 2.24 per cent.; Whitley, 1.05 per cent.; McCreary, 1.50 per cent.; and Wayne. The sulfur percentage average for this area including fifteen important counties is 1.65 per cent. In the western Kentucky field, the great increase in the percentage of sulfur is at once apparent. Ohio County with 3.78 per cent. is the highest and Hancock with 2.87 per cent. is the lowest. The percentages by counties is as follows: Hancock, 2.87 per cent.; Henderson, 3.22 per cent.; McLean, 3.27 per cent.; Muhlenberg, 3.31 per cent.; Hopkins,

Jan 1, 1920

By W. H. Kantner

IN this paper, no attempt will be made to theorize on subsidence. Only known data and actual facts will be given, with a few exceptions noted where other factors and outside influences tend to change sub-sidence directly resulting from porphyry caving. The area under observation is known as the Southeast Extension of the East orebody. The orebody is irregular in outline and dips to the south and the east, extending in depth from about 425 ft. below the sur-face to 1050 ft. below the surface. In the upper horizon, the orebody is about 400 ft. long and 150 ft. wide. At 720 ft. below the surface, the ore outline is approximately 450 by 170 ft.; 70 ft. below this, it is 500 by 110 ft., with an extension at the north end to the east 270 by 120 ft. From this elevation to about 900 ft. below the surface, the ore spreads out to the east and south, being about 700 by 500 ft. between these vertical limits. Below this it pinches out and at 1060 ft. below the surface is only 100 by 100 ft. The nearest point of the orebody-which is on the northwest side-is 600 ft. southeast of the Sacramento shaft. The country rock is all porphyry. Fig. 1 is a vertical east-west section showing orebody and original surface. The surface over the orebody was fairly regular and in this area and adjacent to it were portions of the surface plant, roads, and the main plant railroad to the concentrator. Fig. 2 is a map of the surface over the porphyry area. Caving operations started in April, 1925, at the approximate top of the orebody. The first lift was on the 600-ft. level; the ore was extracted by means of the Morenci timbered slide method and was from 425 to 455 ft. below the surface over an area of about 22,000 sq. ft. This lift was finished in May, 1926. The second lift, on the 650-ft. level, was already in production by May, 1926, so extraction of ore was continuous. This lift was 48 ft. high and covered an area of about 30,000 sq. ft. The ore from this lift was extracted by means of a modified Morenci timbered slide method. This lift was finished in March, 1927. The direction

Jan 1, 1934