Search Documents

By J. D. Kalasky

Continuous mining has revolutionized the coal industry but intensified the problems of earlier mechanization. From the installation of the first miner, it was recognized that face ventilation would be one of these problems. To establish an efficient work cycle for the equipment being used, conventional mechanized mining provides four or more development faces. Continuous mining, relying on a single machine, requires only one face, although more than one can be driven alternately by the same machine. In gaseous areas mined by the older methods, the intermittent rate of exposure allows time for the face to bleed off or be cleared, and the width obtained with conventional units makes it possible to hang a brattice line almost to the face. Continuous mining increases the ventilation hazards; there is no margin of time, and very limited space. For all practical purposes, continuous miners available today can be grouped into two major types, rippers and borers. The two can be further classified, respectively, as flexible and rigid. Both types have been in operation in U. S. coal mines for the past five to ten years in a number of seams, under various conditions ranging from slightly gaseous to very gaseous. Common methods of face ventilation utilizing jute or plastic brattice material for line curtains, stoppings, and checks have so far met with success. Air volumes to operating sections are greater than for conventional mining, and specific instructions have been given to section crews stressing the precautions needed in dealing with a steady rate of gas emission and the importance of maintaining reasonably air-tight brattice to direct a good steady flow toward the face at all times. Operators of continuous miners, as well as the foreman on each section, are equipped with an approved safety lamp for gas testing. When the miner is in steady operation, tests for gas at the face are made at 15 to 30-min intervals, depending on the

Jan 1, 1960

By Edward Keller

Although the subject matter contained in this paper is presented under a new title, its writing was induced by the work of S. Skowronski and K. W. McComas.' A discussion of the latter is here combined with the presentation of new and independent data. The' physical constants quoted by the authors of that paper, such as melting and boiling points, as also the chemical reactions of the substances involved, are so well established that the numerous confirmatory experiments and their application to metallurgical conditions leave little or no room for criticisms. On the contrary, they will greatly aid to dispel any lingering skepticism as to possible considerable losses of copper accruing when the metal is melted in the presence of its own and, probably, other chlorides and when no provision is made for the recovery of volatile products. Exception may be taken, to some degree, to that part of the work under the caption Melting Drillings of Copper Mixed with Sodium Chloride. These experiments should have been extended in order to make the implied reactions clear and the results convincing. The latter are stated to be, "that when sodium chloride is present above certain minimum quantity relative to copper some of it is found to volatilize in the melt while another part reacts with the metallic copper to produce the volatile cuprous chloride, and that when smaller quantities of sodium chloride are present the reaction is complete and all chlorine is found to have volatilized as cuprous chloride." Metallic copper and sodium chloride are mentioned as the sole reagents in this chemical process, acting, according to the authors, in a neutral atmosphere of carbon dioxide. The chemist, quite naturally, wi11 inquire into the formula according to which that reaction takes place and will find that it presents itself as follows: 2Cu + 2NaCl = 2Na + Cu2Cl2 It would appear that the truth of this formula will be challenged and a more rational explanation of the reaction sought. Apparently, carbon dioxide is neutral relative to metallic copper in its molten state; whether it remains neutral in the presence of sodium chloride is quite another

Jan 1, 1921

By David R. Mitchell, R. B. Hewes

MANY processes for cleaning coal that are in use depend primarily on physical properties of coal and refuse other than specific gravity and surface conditions relating to froth flotation. These properties are' shape, coefficient of sliding friction, resilience, friability, magnetic susceptibility, and electrical conductivity. In many of these processes specific gravity does have some effect and many separators are designed to utilize more than one of the physical properties cited. Although the processes described herein do not have a widespread application, yet for specific coals and specific conditions, they are economically important. A problem confronting many coal-mining districts is the marketing of the slacks or screenings and dust passing the final sizing screens. Proc¬esses in commercial use installed primarily to increase the form value, and hence the market value, of these slacks and dusts include briquetting, packaging, and low-temperature carborization. MECHANICAL PICKERS Machines utilizing shape, frictional resistance, and differences in resilience of coal and impurities are usually called mechanical pickers. They require a closely sized feed, therefore their use is confined to the pea, nut, and egg sizes. Various types of these devices are described by Berrisford, 1. 2 Taggart, and Yeele.

Jan 1, 1943

By Eben E. Olcott

The Mine.-For some years attention has been drawn to the copper deposits of the Appalachian range of mountains, and especially to those in that portion crossing the corners of Virginia, North Carolina, and Tennessee. Certain it is that in many places in this locality available deposits of copper await the miner, and one after another are being opened and worked. The parts of these three States alluded to are but sparsely settled, and communications are insufficient to meet the demand for transportation. Railroads are wanted, as the existing wagon roads are unfitted for heavy hauling; these circumstances increase very much the difficulties in the way of mining enterprises. Notwithstanding this, the success of some of the mines of this section is an established fact, and Ducktown has for some years held a high rank among the copper-producing localities of the United States. Of all these deposits, however, none is more interesting or more deserving of attention than the one now under consideration. The works of the Ore Knob Copper Company have been energetically pushed forward, since the reopening of the mine, in the spring of 1873, by Mr. J. E. Clayton, the superintendent and one of the chief owners of the property, and if one thing more than another can insure success it is the combination in this gentleman of rare business capabilities with the deepest personal interest in the pros¬perity of the undertaking. The copper vein -at Ore Knob* is a clearly defined fissure traversing the gneissic rocks of Pre-silurian age in a direction 61° east of north. * The reader is referred to a paper by Dr. T. Sterry Hunt, in the second volume of the Transactions of the Institute, on the "Ore Knob Mine, and some related Deposits," pages 123 to 129.

Jan 1, 1875

PHILIP D. WILSON,* Warren, Ariz. (written discussiont).-Mr. Tovote's idea of attempting to classify according to their broad geologic relations the ore deposits and prospects of the Southwest is an admirable one. Attempts have been made to evolve some comprehensive scheme of classification that would be of practical assistance in determining the possible value of prospects, but the ore deposits are too varied in type, form, genesis, and distribution to lend themselves readily to any definite, scientific pigeon-holing. The classification Mr. Tovote recommends, combining the age of the mineralization with the type of the rock supposed to be its source, is open to criticism even on the evidence he presents. The age of many deposits is not nor can be definitely determined because of the absence of sedimentary rocks in their vicinity. Furthermore, the character of the mineralizing solutions has, in a large majority of cases, no relation to the composition of the associated igneous rock. While the solutions may have originated in the same magma, they were usually a much later manifestation of it, often appearing after the intrusive rock had completely solidified and been subsequently crushed and fractured, and in many cases the chemical difference is very marked. It is true that igneous activity in the Southwest is definitely related to-certain geologic periods. The statement, however, that no ore deposits can unmistakably be referred to periods earlier than late Cretaceous is not supported by fact. The bonanza copper orebodies of the Jerome District are definitely pre-Cambrian. As suggested by J. R. Finlay,1 they are probably post-Beltian or late Algonkian in age, perhaps related to the same great mountain-making period as the copper deposits in the Keweenawan series of Lake Superior and the Sudbury, Porcupine, and Cobalt deposits of Ontario. The proof that they are pre-Paleozoic may be summarized as follows: 1. The pre-Cambrian complex in which they occur is overlaid by a great thickness of Paleozoic sediments with the Tonto or Tapeats sandstone at their base. The only primary mineralization in these sediments is an economically unimportant one connected with very recent basalt. 2. In the United Verde Extension mine, the gossan over the great orebody extends to the old pre-Cambrian surface where it is directly

Jan 2, 1919

By Horace Williams

IN VIEW of the frequent occurrence of petroleum in other parts of the world, it seems odd that so large an area as is contained within the borders of Brazil should be without this product. This apparent deficiency may be due, however, to our ignorance of the regions in which-it, may exist. In some places, indications point to the probable existence of petroleum in ages gone by; and while the presence of petroleum pools may be problematic, in several regions conditions not unfavorable to their occurrence exist. Yet, Brazil has enormous oil resources in the rich oil-shales in different parts of the country. Many of these shales are very rich and only suitable processes for the extraction of the oil are lacking. At the present time, only a few small experimental plants are producing oil by distillation from these shales. These plants have been the subject of recent investigations by the Geological and Mineralogical Survey, a. pre-liminary report of which is in the hands of the printer. The only regions where studies have not been made are the upper Amazon, the Acre, the Rio Negro, and the Peruvian frontier, which really seems to be the most promising field for, explorations of any in the country. In the vast plateau region of the interior north of the 20th parallel of latitude, granites, gneiss, mica schists, and, very old metamorphosed sedimentaries predominate. Later, sedimentaries occupy a minor position and, where found in the interior, represent a thin veneering resting on the older rocks. At several places near the coast they have a greater development and contain considerable beds of oil-shale and may, in some cases, offer conditions favorable for the occurrence of oil. Such deposits are found in the Permian rocks of central-and southern Maranhão; in the Tertiary and Cretaceous beds along the coast of Alagôas Sergipe, Bahia, and perhaps farther south in Espirito Santo; and in the Parahyba embayment north of Cape Frio and in the interior Tertiary basin of eastern Sao Paulo.

Jan 9, 1920

By K. L. Ludeke, A. D. Day

For many reasons, it appears that deep rooted, perennial shrubs offer potential for improved stabilization and provide maintenance free vegetative cover to harsh sites where perennial grasses have not been successful. The major objective was to select various shrub species of arid plants for initial soil stabilization of disturbed mining areas. The very fact that a drought-adapted shrub has a massive root system that can use moisture from a greater volume of mineral waste soil materials suggests that arid environment disturbed soils may be vegetatively stabilized using desirable forage shrubs. A secondary effort is underway to assemble information and plant materials of promising species from many arid regions of the world for reclamation of mined lands. Surprisingly, many of the better plants for arid sites are quite high in protein content. With proper management, breeding, and selection, they may prove to be very desirable livestock feed when mined lands are used in range land areas. Advancements in arid land solid waste stabilization hold favorable promise for many industries that mine and mill in arid regions for effective reclamation of disturbed areas. Particularly exciting is the possibility of establishment of high density maintenance free vegetative cover of climax vegetation that reclaims the disturbed area back to its original land use. Due to high shrub productivity, stabilization potential, nutritional quality, and reclamation success, greater use should be made of shrubs in disturbed land reclamation associated with mining and milling operations in harsh aril environments.

Jan 1, 1986

THE great event in American affairs was the sudden death of President Harding, on Aug. 2, in San Francisco. A few hours later Vice-Presi¬ dent Coolidge took the oath of office while in his father's farmhouse in Vermont and forthwith proceeded to Washington as the 30th president of the United States. The French and Belgian governments' replied to the British refusing the proposed discussion of the German offer and declaring that they would pursue their policy in the Ruhr until the German government abandoned its resistance and surrendered unconditionally. The economic collapse of Germany .appears to be nigh. Chancellor Cuno and his cabinet resigned the govern-ment of Germany on August 12, and Gustav Strese-mann, head of the People's party, accepted the task of forming a four-party coalition government. Coinci-dentally, there were food riots throughout Germany, and many persons were killed and wounded. The , National Assembly of the Turks at Angora ratified the Lausanne treaty, in the latter part of August, whereupon the retirement of the military forces of the Allies from Constantinople and the Straits began. Thus, Turkey was fully reinstated as a European power. The Greek government also ratified the Lausanne treaty and commenced to put its army on a peace basis. The number of unemployed persons in Great Britain is again increasing, which is causing much concern. The flood of crude oil and gasoline, which is severely taxing storage capacity, had its natural economic effect. Some small refiners were constrained to liqui-date in distress. The Governor of North Dakota, having acquired a supply of such cheap gasoline, insti-tuted a drastic cut in price, deliberately egging on the big refiners to do likewise. The Standard Oil Co. of Indiana accepted the challenge with enthusiasm, say-ing that it had always been its policy to sell as cheaply as any competitor. There was a humor in this situation which paved the way for the Standard to extinguish its small competitors and do by invitation of the State exactly what the muck-rakers had always charged as its greatest crime. The gasoline war spread to other states and reductions in price were made even on the seaboards. All of this was purely economic.

Jan 8, 1923

Butte Meeting. It is expected that the technical program of the Butte meeting will be a sufficient attraction to draw to that point every member who can possibly get away long enough to attend. Attention is particularly called to the papers already sent in by the Committee on Precious and Base Metals, and the papers which they are undertaking to secure for the meeting, as published on pp. ix and x. In addition to these papers, and in addition to those published in this Bulletin, the office of the Institute already has in hand several papers, which will be published at an early date, and presented in abstract and discussed at the meeting. Of the discussion of these papers a special feature is being made. Therefore, let every member come to Butte who can do so. A meeting of the Board of Directors of the Institute will also be held at Butte. In the May Bulletin, we stated for the information of members the railway excursion rates for two suggested tours in connection with the meeting, which included Glacier Park before the meeting and Yellowstone after it. The itineraries there given and rates quoted were planned and offered by the railway agent bureaus in New York. Circulars have been sent to the members of the Institute by A. E. Vaughan & Co., a tourist trip agency of New York City, containing details of tours nearly identical with those outlined in the Bulletin, and quoting rates covering, the expenses of the whole trip. Members can easily compare these rates with the rates offered by the railroads, and published in the last Bulletin. In order that no misapprehension may exist, the statement is here made that the Institute and its officers have no connection whatever with Vaughan & Co.'s proposals and that any such tours will be strictly personal matters between said company and the members of the Institute who take them. Nevertheless, the Board of Directors calls to the attention of members the circumstance that tours such as these will afford an opportunity for members to travel together to the meeting.

Jan 6, 1913

By Guilliaem Aertsen

THE derivation of the word tire (or tyre, as it is spelled in England) is obscure. Some dictionaries suggest that it is the aphetic form for "attire, covering," so called as being the outside covering or band of a wheel; also as a corruption of "tier," the band which holds, or "ties," the rest of the wheel together. One dictionary states: "The supposed derivation of the word is that bands were first used on wheels in the City of Tyre, Syria. " In the infancy of railroads, the tracks consisted of flat baits of iron, spiked or bolted to the upper surfaces of longitudinal timbers, which; in turn, rested upon masonry foundations. Stone blocks installed for this purpose on the old Germantown & Norristown Railroad, now the Chestnut Hill branch of the Philadelphia & Reading Railway, were to be seen for many years on the right-of-way, north of what is now. Wayne Junc-tion, Philadelphia, Pa. The "cornerstone" of the Baltimore & Ohio Railroad was laid Apr. 4, 1828, and the first locomotive in America was built by Peter Cooper at the St. Clair Works, Baltimore, Md., in 1829 "to demonstrate its adaptability to a curved road." It is believed that the first successful locomotive was built in Philadelphia by Tyler & Baldwin in 1832 for the Germantown & Norristown Railroad. Rufus Tyler-and Matthias Baldwin were brothers-in-law; the latter's name will he identified with American locomotives until locomotives are forgotten. The Wheels on these first locomotives, designed to run on this primitive rail, were shod with plain iron bands, bent and welded. The flanges consisted. of separate iron bands, bent sidewise, welded, and, bolted to the sides of the wooden follies, or rings. Before many years had elapsed the tires were fabricated of iron bands, rolled in one, piece with the flange projection on the side. The tire for each wheel was bent and welded and subsequently attached to the wheel center by shrinkage, bolts, rivets and various mechanical devices.

Jan 1, 1917

By H. C. Heard

The review by Professor J. C. Jaeger (Chapter 1) briefly summarizes and discusses a select group of papers by various workers dealing primarily with aspects of fracture in brittle rock materials. Professor Jaeger's treatment is primarily concerned with the correlation of phenomenological and theoretical failure criteria with empirical results from short duration tests at ambient temperatures and generally at low lithostatic and interstitial fluid pressures. As engineering rock mechanics becomes more concerned with new techniques of mineral exploration and production at increasingly greater depths in the crust, it is well to be aware of the effect of the environment -that of the superposed stress field upon the lithostatic and interstitial fluid pressure, the temperature and the duration of the loading upon the failure of rocks either by fracture or flow. All results to be discussed here are from laboratory tests on small homogeneous samples, thus caution should be used in the direct extrapolation of these results to large inhomogeneous rock masses having quite different boundary conditions in the earth. The purpose of this supplement is to briefly point out the major effects of these parameters as examined singly, with all others held constant, and to cite some recent results which apply to the main theme on the brittle failure of rocks. The total stress field imposed upon a small volume of porous and permeable rock in the earth's crust may be thought of as the sum of an applied differential stress, plus a lithostatic pressure, plus an interstitial fluid pressure. The differential stress portion may be completely specified by nine components, six shear and three normal. If the small volume element is in rotational equilibrium, by suitably choosing our coordinate axes we may resolve these nine components into the three principal com-

Jan 1, 1967

By Blamey Stevens

It is now generally agreed that most metals have been brought to the surface of the earth by volcanic agencies. The question as to how these metals came from the volcanic matrix to the mineral deposit has been often discussed. It might be useful to give more serious consideration to the ultimate origin of the volcanic material. It is possible that some light might thus be shed on the persistent associations of some metals with certain particular kinds of rocks. For example, the very general association of gold with acid types of igneous rocks, of tin with granites or quartz-felsites, of certain types of deep-seated copper-deposits with magnesian eruptives, and so on. One interesting question is as to whether the metals brought near the surface by volcanic agencies appear here for the first time, or whether they came from the central core of the earth. The interior of the earth is, without doubt, much more highly metallic than the crust, and so the core is often thought to be the origin of many of the metals which are uncovered by man. The Differentiation Theory.—Although a great many theories bearing upon these matters have been discussed,' the only one now considered as worthy of much consideration among American geologists is the " Theory of Differentiation of Igneous Magmas."2 According to this theory, lakes of molten magma are supposed to exist very far down beneath the earth's surface. In these lakes a process of differentiation is supposed to be going on whereby the liquid magma is split up into two or more liquid phases. Each of these phases is supposed to take with it the metallic constituents for which it has the greatest affinity.

Jan 1, 1913

By Richard Amberg

While the old-time melter was satisfied to bring his metal out in the desired condition, and therefore took care to have the slag liquid enough, the importance of a thorough knowledge of the slag is at present recognized in all up-to-date melting-shops. Formerly slag or cinder was considered a necessary evil, accumulating in some mysterious way wherever a man was striving to produce a clean metal. Nowadays we deliberately aim at a well-defined slag, which varies with the nature of the process and the product. In steel-making we need slag for two main purposes, namely, refining and protecting the metal. To refine metal, essentially oxidizing and reducing processes are required, while to protect the metal we need a reducing or, still better, a neutral atmosphere. Although an absolutely neutral condition between steel, on one side, and the containing vessel and the slag, on the other, is an imaginary conception, the various furnaces in use for the production of liquid steel maybe arranged with respect to the attainment of this ideal in about the following order of merit: converter, open-hearth, crucible, and electric furnace. In dealing with the subject we will find it convenient to avail ourselves of the terms of physical chemistry, which yield a simple conception of the matter and an expedient way of expression. Slag and metal at large are not mixable with each other, and we will therefore call them the two " immiscible phases," though there are certain compounds which dissolve in both phases under conditions to be considered later. Reactions be-

Jan 1, 1913

By Dorsey Hager, G. W. McPherson

The rapid increase of water troubles in the Mid-Continent oil fields is causing much alarm. Troubles occur at Towanda, Eldorado, Augusta, Cushing, Blackwell, and Healdton, although they had not been acute in the Mid-Continent field until about two years ago, when the unusual conditions in the deeper oil fields were first encountered. California faced the same situation, but, thanks to aggressive measures, has largely overcome the dangers. The following analysis of water trouble may throw some light on the subject and be of assistance in solving the problems involved. Water Troutles Classified The presence of water in large quantities in oil sands has the following results: 1. Diminishes oil production. 2. Diminishes casing-head gasoline production: (a) By curtailing the gas flow. (b) By making the use of vacuum pumps unsuccessful. 3. Increases lifting costs: (a) By making it necessary to pump large quantities of water, which requires a fast motion and long stroke (third hole). (b) By requiring the use of compressors for air lift. (c) By causing break-downs and delays due to the high speed necessary to pump water. (d) By making it necessary to treat "cut" or emulsified oil. Oil production is seriously curtailed by the presence of large quantities of water. Lease records show that wells are shut down 40 to 60 per cent, of the pumping time where serious water trouble occurs. While a small quantity of salt water may cut the paraffine and keep the oil moving, several hundred feet, or a hole full of water, effectually "kills" the oil and gas. The quick return of wells to production, once the water is shut off, shows how wells have been affected. The killing of gas sands

Jan 1, 1920

By H. M. Boylston

Metallic manganese was first produced in 1773, by Sven Rinmann, a Swedish mineralogist. In 1799, William Reynolds, of Ketley, England, obtained a patent on the use of manganese dioxide in the manufacture of steel, and in 1808 an English patent was granted to John Wilkinson covering the use of manganese ore, or manganiferous ore, as an addition to iron ore in the blast furnace for the production of a superior grade of pig iron. Karsten showed in 1816 that manganese increased the hardness of iron without decreasing its malleability or toughness, while it caused pig iron to be more white in fracture and more fusible. The first practical application of manganese to steel-making, however, is attributed to Josiah Heath who discovered in 1839 (less than 90 years ago) that manganese conferred upon steel the properties of being more easily worked and welded under the hammer. When Bessemer invented the pneumatic process of steel-making which now bears his name he was at first successful because, as it afterward developed, he was using a Swedish pig iron high in manganese. When his supply of this material ran out, he used a low-manganese pig from English sources and failed signally to produce a steel which could be rolled, while his Swedish licensees were continuing their successful application of his method. And it was not until Robert Mushet, in 1856, suggested the addition of manganese in the form of spiegeleisen to the molten product of the converter that success again came to Bessemer. In 1866, William Siemens patented the use of ferromanganese as an addition to molten steel to counteract the bad effects of sulfur. It was in 1888 that Robert Hadfield published at some length his account of the effect of manganese as an alloying element in steel and described the unique properties of the now famous Hadfield manganese steel containing about 12 to 14 per cent. manganese and 1.25 per cent. carbon. Function or Manganese in Steel-making Bessemer's failure at one period of his experimental work to make steel which could be forged successfully was due to the fact that the

Jan 1, 1927

By R. E. Bedworth, N. B. Pilling

The corrosion of metals is one problem on which time and thought have been expended for many years. In the effort to avert the destructive action of a hostile environment, attention has been directed almost entirely to the conditions under which most metallic structures are called upon to perform, and the extensive and complicated phenomena attending the corrosive action of atmospheric agencies, acting at the ordinary atmospheric temperatures, have been studied, but there is unanimity of opinion regarding many fundamental facts. One neglected phase is the corrosive action of various gases upon metals exposed to temperatures considerably higher than the atmospheric range, and more especially the attack of atmospheric oxygen upon exposed metallic surfaces. That the problem is difficult is connoted by the practical dominance of industrial electric heating by alloys of one type (nickel-chromium). Proprietary interest may account, in part, for the paucity of information available upon even the most general factors determining the behavior of metals and alloys when exposed to such exacting conditions. The present paper gives some conclusions reached as the result of experimental work, extending over several years, on the mechanism and contributory factors of the high-temperature oxidation of a number of simple unalloyed metals; it is free from experimental detail and proof. High-temperature metallic oxidation may be considered as a phase of metallic corrosion. The scheme outlined below, in which corrosive agent and environment are the principal criteria, is one way of analyzing the several groups of corrosion phenomena. Erosion.—Disintegrating or destructive action by physical causes. Corrosion.—Disintegrating or destructive action by chemical causes. Low-temperature Corrosion.—Solid participating phases essentially immobile: (a) Gaseous agent; (b) liquid agent: action electrolytic and action non-electrolytic. High-temperature Corrosion.—Solid participating phases possess diffusive mobility: (a) Liquid agent; (b) gaseous agent: reducing gases, oxidizing gases. (1) Water; (2) miscellaneous elemental and combined oxygen.

Jan 1, 1923

By Edward Steidle

IT has been said that "the command of nature has been put into the hands of man before he knows how to command himself," and what we see about us gives particular emphasis to this observation. If this condition be granted, the vaunted boast of school and college, of the institution that had the training of this generation, and of its fathers, and of its grandfathers, the boast that education is a "preparation for life," stands exposed as a hollow claim, or as a ghastly, cynical conception of life, or else education has fallen far short of its intentions. It has been evident for some time that education was not meeting the fullest expectations of society. In recent years there has been a deal of speculation indulged in by both laity and faculty in regard to American education and American civilization, and some few and sporadic changes have been effected. Today, however, there is no longer time for mere hypothetical considerations; we are faced with certain definite facts and confronted with obvious conditions that will not wait for fine-spun theories. If educators do not put their house in order, someone else will do it for them. The trends in mineral industries education must be in harmony with this general realignment that is today visible on the educational horizon, and only as these trends are in conformity with this movement can they be called sound. Two questions, then, confront mineral industries educators: (1) What are the trends in mineral industries education, and (2) how do these trends correlate with the major educational movements of the day?

Jan 1, 1933

By Augustus Locke, Paul Billingsley

The mining districts of the first order' of the western United States (and borders) are those named on Fig. 1. These fall into four groups: (1) in the eastern outliers of the Rocky Mountain system; (2) in the Rocky Mountain system itself; (3) in the Great Basin; and (4) in the Sierras and Coast ranges. Of these four groups, the first three are almost entirely of Tertiary age and are within a belt of compressive folding which we shall call the Rocky Mountain-Great Basin thrust arc. The backbone of this belt is shown by the line BAC. The position of the ore districts in this belt indicates a conformance to linear elements of the continental pattern. These are additional to the peripheral elements emphasized by Butler.2 Nature of the Thrust Arc The thrust arc separates regions of contrasted kinds. To the east of it are flat-lying plateaus interrupted by earlier mountain folds; to the west, sunken basins, in which block-faulted ranges lie like an anchored fleet in a sea of desert wash or lava. The. cross-sections are as shown in Fig. 2. The backbone of the belt is the upward and eastward moving block represented by the Glacier Park, the Wasatch, and the Virgin mountains, successively. The structure represented on these sections is the culmination of events which began far back in geologic time and throughout which a contrast has existed between the regions east and west of the backbone line. Before the Pennsylvanian, as Fig. 3 shows, there was a shallow shelf on the east and a deep marine trough on the west; after

Jan 1, 1935

By L. B. Berger, W. P. Yant

This paper presents evidence of the general occurrence of methane in a large number of the coal fields of the United States and substantiates the apparent unnecessary differences in the ventilation requirements and codes in the various states, as was brought to the attention of the Committee on Mine Ventilation of the American Institute of Mining and Metallurgical Engineers at its Pittsburgh meeting in October, 1925, by J. A. Garcia. The data in his report have been compiled from the files of the Gas Laboratory of the Pittsburgh Experiment Station of the Bureau of Mines and represent samples collected throughout the various states and submitted for analysis by its engineers, also by mine operators and State mining departments, since 1911. Several thousand analyses were available but most of them were rejected because they represented abnormal conditions, undefined place of sampling, special investigations, or duplications in the same mine. Only those samples were included which, without reasonable doubt, were ascertained to fall within three major classes, namely, main return, air splits, and face and rooms of live workings. In the case of air splits, and face and room samples, only the one which contained the highest percentage of methane found in a given mine was taken. OCCURHENCE OF METHANE IN COAL MINES OF THE UNITED STATES Obviously it is not feasible to present the detailed analytical data here and accordingly these data have been compiled into groups in a manner which it was thought would bring out clearly their significance. These are shown in Table 1 which includes the analyses of 310 samples of return air of approximately the same number of coal mines in 19 states. Because of changes in ownership and names the exact number could not be ascertained. The table also includes 337 samples from air splits and 263 from the face and rooms of some of the same mines represented by return air samples and from other mines in these states. A total of more than 400 mines are represented by Table 1.

Jan 1, 1927

By Hewitt Wilson

CHALK is soft, pulverulent limestone formed from calcareous remains of microscopic organisms. Whiting is the powder made by the fine- grinding of limestone. Although European chalk dominated the early American market and is still shipped to the eastern and western seaboards, the domestic producer, by new technical processing, improved equipment, and proper selection and mixing of raw materials has shown that the United States can be independent of foreign sources. DISTRIBUTION European Chalk-Outcrops of Cretaceous chalk are found in the area roughly bounded by Antrim, Ireland, on the east, East Prussia on the west, Sweden and Scotland on the north, and Nice, France, on the south. Commercial chalk is mined from the chalk cliffs between Dover and Hull, England; from deposits near Mons, in the Departments of Pas de Calais and Nord in northern France; and from similar de- posits in Denmark and Belgium. United States-Some grade of limestone is found in every state of the Union, but true chalk of Cretaceous age is limited to three large areas in the central and southern states. Niobrara (Cretaceous) chalk outcrops are found as a narrow band encircling the Black Hills in South Dakota, Wyoming, and Nebraska, and in much larger exposures in southeastern South Dakota, eastern Nebraska, and western Kansas. A third chalk belt extends from west central Arkansas into Oklahoma and connects with the Austin beds, which almost cross Texas. In the southeastern states, the Selma chalk extends from western Tennessee south through northern Mississippi and turns east across central Alabama. Most of the domestic chalks are discolored with iron oxide or carbon. Some marls can be included with chalks of commercial possibilities. Some of the soft, cream-colored limestones of northern Florida, Georgia,

Jan 1, 1949