Search Documents

By R. L. Curfman

WHEN the Uranium Reduction Co. mill was put on stream in October 1956, one of the many operational problems was that the sand-slime separation circuits could not produce a satisfactory RIP feed, inasmuch as production greatly exceeded de- sign capacity. The original cyclone portion of the circuits consisted of two stages of three 14-in. cyclones in each circuit, as shown in the condensed flowsheet. The high percentage of +325 mesh material in the over- flows of these 14-in. cyclones was not consistent with good operation, and flow rates per ton of ore were high, indicating that not enough of the total solids in the ore was being rejected as sands. It was inferred by members of the metallurgical department that returning the underflows, or sand fraction, from these cyclones back into the drag classifiers was the primary reason for dirty feed.

Jan 7, 1958

Spencer Gulf takes off from the Great Australian Bight cutting a 200 mile deep wedge of water into the South Australia coastline. A pale winter sun shines yellowly on the choppy surface of this body of water which is progressively more salty as it approaches Port Augusta at the head of the Gulf. Once Port Augusta thrived as a grain port and the speedy clipper ships began or ended their legendary races there. On the eastern shores of Spencer Gulf, farm land spreads away from the water's edge. The western side of the gulf meets marginal grazing land of acacia tree and salt bush. Part way down the gulf, there are two industrial towns facing each other from opposite shores; Port Pirie on the east and Whyalla on the west. These towns are like half brothers, the common parent being the founders of Broken Hill Pty. Ltd., (BHP) who began lead smelting at Port Pirie and discovered iron ore near Whyalla needed for the lead smelting process. The iron deposits later became the inspiration for BHP's iron and steel business.

Jan 10, 1964

By W. T. Jr. Thom

INTEREST naturally attaches to fissuring and subsidence of the earth's surface, whatever the cause may be, and the induced movement and fissuring of the impervious strata overlying an oil sand is of even greater practical importance because of its bearing upon the recoverability of the portion of the oil not already extracted or extractable by ordinary production methods. It is probably true that significant ground movement induced by oil production occurs only in oil fields in relatively young formations, where the oil comes from incoherent or only slightly cemented sands and oil-soaked clays, but inasmuch as a great proportion of our "gusher" wells produce from "running" sands and yield a large part of the total oil output, it seems worth while to make an effort to inspire the collection and recording of data indicating the nature and magnitude of oil-field subsidence, both surface and subsurface.

Jan 1, 1927

By J. Donald Graham, John G. Kuhn

The goal of any development drilling program is the drilling of the exact number of holes necessary to adequately determine grade and dimensions of an ore body, no more and no less. Any technique which eliminates unnecessary drilling costs produces beneficial results, both to the company and to the person who can claim the savings. The method for controlling development drilling programs to be described was developed during the latter part of a major development drilling project at the Christmas mine of Inspiration Consolidated Copper Co. in Gila County, Arizona. It was used to test the need for drilling individual holes but could be expanded to control an entire project. Application of this method involves an evaluation of geological conditions present and a good bit of common sense. Projects involving large disseminated, rather homogeneous ore bodies of the porphyry-copper type would be the most likely candidates for application of the technique. Discontinuous ore bodies would not be amenable. The method is based on the measurement of the linear correlation between the spatial distribution of two sets

Jan 1, 1973

By Philip L. Collyer

A technique for evaluating the similarity of ore deposits is presented. A Q-mode cluster analysis is performed using information on tungsten mines in North America. This is a method of grouping several samples according to their similarity based on a simple matching coefficient. Tungsten mines are grouped or clustered on the basis of geologic variables. It is possible to interpret and evaluate different ore environments according to age, mineralogy, and other variables. It is well known that variable geologic conditions influence the occurrence of certain types of minerals. If one variable is responsible and identified, that variable can be searched for in exploration. If several interrelated variables are responsible for forming a favorable environment, then recognition and identification may be more difficult or completely masked. Therefore it is helpful in exporation to isolate and identify multiple interrelated variables which control the localization of mineral deposits. Cluster analysis is useful in mineral exploration where considerable amounts of data are available for analysis. Subtle relationships that might be overlooked because the data are voluminous can be isolated using this technique. Cluster analysis can be used to establish exploration prioriy in unknown areas on the basis of similarities to known metallogenetic provinces.

Jan 1, 1976

By M. J. deBastiani, John Kostuik

The Denison orebody, located on the north limb of a syncline, rests at depths of 800 ft in the northern end of the property to 3000 ft at the southern end, and has a composite dip of 19º, varying locally from 0º to 45º. It is composed essentially of two pyritized conglomerate beds separated by a varying thickness of quartzite. The thickness of the upper conglomerate reef of the main ore zone varies from 2 to 15 ft while the lower reef is from 2 to 12 ft. Mining, whether carried out over the entire section of the reefs and quartzite or by selective mining of the reefs, is accomplished by room and pillar methods, with an initial 67% extraction on the advance towards the property boundaries. The underground ore handling requirement in such an orebody has become one of the most challenging problems in mining.

Jan 8, 1966

By M. L. White, J. L. Shafer, C. L. Caenepeel

Often an in situ leach is the only practical economic method for copper recovery from small low grade oxide deposits. The decision to develop a copper property by an in situ blast and leach is strongly dependent on ore grade, tonnage, hydrology, and the copper extraction and acid consumption rates. The inherent leachability of the ore will in part determine the desired amount of fracturing of the ore deposit by the blast in order to obtain a copper extraction rate that is economical. For the last several years Occidental Research Corp. (ORC), has undertaken a modest effort to address the question of how to best identify and determine the information necessary to predict and control the operation of an in situ leach for the economic recovery of copper.

Jan 2, 1979

By Michael Hoch, Michel Desjardins

The isothermal section of the Mo-Ti-Zr-0 system at 1500°C was investigated using X- ray diffraction and mefallographic techniques. Up to 66.7 at. pct 0, the system contains ten four -phase regions. Isopleths at 10, 30, 45, 55, and 60 at. pct 0 were constructed. THE purpose of this investigation was to determine the general shape of the quaternary equilibrium phase diagram of molybdenum, titanium, zirconium, and oxygen at 1500°C. The system was truncated at 66.7 at. pct o. PREVIOUS INVESTIGATIONS The Ti-Zr-0 system was investigated in this laboratory.' The binary systems of interest have been compiled and discussed by Hansen' and Levin, McMurdie, and Hall.3 Farrar, Stone, and Margolin studied the titanium-rich corner of the Ti-Mo-0 ternary. MATERIALS The titanium powder, 99.6 pct pure, the zirconium dioxide, and the molybdenum powder were supplied by the Fairmont Chemical Co. The zirconium powder,

Jan 1, 1962

By John S. Sumner

The various electrode arrangements used in induced polarization (IP) surveying can be classified according to the geometry of the electric field being measured. The simplest geometry (Wenner, Schlumberger, gradient) is the parallel or plane-wave electric field, while the three-array and pole-dipole array measure the field about a point current electrode. In the dipole-dipole array the characteristics of a dipolar field are approximately measured. The drill hole arrays employ variations of these fundamental geometries, depending on the objectives of the survey. This report compares the relative advantages and disadvantages of each of the commonly used surface and drill hole IP electrode arrays. Factors of each array that are considered are signal-to-noise ratio, EM coupling rejection, speed and cost, and resolution of polarizable bodies. It is concluded that certain arrays are better suited for different exploration objectives and for different geological conditions. Also the type and capabilities of the IP surveying equipment and method limit the choice of arrays.

Jan 1, 1973

By Richard H. Sibson

Changes in seismic style along the San Andreas fault system appear to correlate with strike-parallel variations in regional heat flow. Large earthquake ruptures are associated with colder segments of the fault zone, while comparatively high levels of microearthquake activity and small to moderate shocks occur along the hotter segments, often in association with aseismic creep. Such behavior is consistent with geotherm and strain rate dependent profiles of shear resistance versus depth, constructed for quartz-bearing rocks. These profiles suggest that the transition from frictional to quasi-plastic behavior with depth should increase by a few kilometers passing from the hotter to the colder portions of the fault zone, giving rise to long-wavelength concentrations of distortional strain energy near the base of the seismogenic zone in the cold segments. Some support for this hypothesis comes from the observed deepening of microseismic activity passing northwest and southeast from the central Californian active region to the currently locked, ~400 Ian segments of the San Andreas fault that ruptured in 1906 and 1857.

Jan 1, 1982

By R. M. Wilhelm

HIGH-TEMPERATURE thermometry,, as treated in this paper, deals with the measurement of temperature in the range 100° to 550° C. The lower limit corresponds to the temperature of boiling water at normal atmospheric pressure, the upper limit is approximately the highest temperature to which mercury in a glass thermometer may be safely subjected.1 In this range., the domains of pyrometry and thermometry overlap somewhat, for high-temperature resistance thermometers and thermocouples generally classed as pyrometers are often used below 550° C. This paper will be confined to high-temperature mercurial thermometers, and indicating and recording thermometers of the vapor pressure, liquid or gas filled, and bimetallic or graphite-metal expansion types, a classification of which is as follows: CLASSIFICATION OF THERMOMETERS GENERAL CLASSIFICATION SUBDIVISIONS Mercury in glass Laboratory- Etched or engraved stems (mercurial) Enclosed scale (Einschlus) Industrial Vapor pressure Indicating and Pressure Liquid filled recording Gas filled Bimetallic Graphite-metal expansion

Jan 9, 1919

By S. A. Braley

DRAINAGE of acid mine water into surface streams of coal mining areas is one of the most serious problems of stream pollution, since there is no known method that completely prevents its forming and no economically feasible treatment after it has formed. The mine acid problem differs from other pollution hazards because acid production does not end with cessation of mining but actually becomes more evident when pumping is stopped. The acid problem in the Pennsylvania, Ohio, West Virginia, and Kentucky bituminous coal areas of the U. S. began with the first operation in 1761, and the volume of acid discharge today is largely the cumulative result of years of mining. Provided they lie above the drainage area, the oldest mines, now long abandoned, are almost without exception producing acid in the same manner as those now operating or recently abandoned. It is well to consider some of the many procedures that have been used to determine the composition

Jan 1, 1957

By Sidney W. Poole

THE control of deoxidation, together with other factors involved in electric-furnace melting practice, to consistently produce heats of high-quality alloy steel to stringent specifications as to nonmetallic inclusion content is a problem of considerable magnitude. Steel melting as an industrial process is subject to many variables that can influence the quality of the product made. In order to modify the size, amount and distribution of inclusions and to promote their elimination, deoxidation, among other practices, plays a major part. The primary purpose of deoxidation in the production of electric-furnace alloy steels is the removal of dissolved oxygen present as FeO in the bath, which is produced as a result of prior oxidizing conditions. The elements usually added to effect this removal of soluble oxygen are those that will, upon addition, cause the formation of an oxide compound insoluble in the molten steel bath as silica, alumina or silicate combinations.

Jan 1, 1947

By Thomas E. Howard

Recipient of the 1975 D. C. Jackling Award - "For his vision and initiative in defining, planning, directing, and accomplishing mining research programs; for his leadership in focusing worldwide attention on the need for research to improve underground excavation for mining and civil applications; and for his lecture. . ."

Jan 1, 1976

By J. M. Lohr

THE characteristics and uses of thermocouples of platinum and the platinum alloys being so well known, this paper will be confined to base-metal couples. During the past decade, there has developed a strong demand for thermocouples made of metals cheaper than the platinum alloys, and suitable for industrial heat measurements. Much research has been clone but only a very limited number of alloys have been found to possess the necessary characteristics for general technical use. In the development of thermocouple alloys it is necessary to consider the following points: The electromotive force and temperature relations; permanency or constancy; reproducibility; manufacturing difficulties; durability; and accuracy in use. The electromotive force developed by the thermocouple should increase with the rise of temperature according to some definite law. It is desirable that the electromotive force should vary directly with the temperature difference of its junctions, in other words, giving a curve linear or nearly so. It is also desirable that the resulting electromotive force be as large as possible for any given range of temperature, thereby insuring greater accuracy of readings.

Jan 9, 1919

By Thomas H. Leggett

The conditions surrounding this mine are, perhaps, not sufficiently rare or significant to warrant special attention. A certain interest, however, attaches to the locality through the recent discovery of fossil cycads made there by Mr. Charles M. Rolker, of New York, who has repeatedly visited this district, fixing the geological horizon

Jan 1, 1889

By W. Petruk, R. S. Boorman, R. Gilders

Approximately 33% of the silver in the Zn-Pb-Cu-Ag ore of Brunswick Mining and Smelting Corporation Limited is lost to the tailings and an additional 11% to the zinc concentrate for which no payment is received. 38% to 44% of this lost silver is carried by tetrahedrite, 28% by galena and 28% to 34% by a third silver carrier. The silver minerals acanthite and pyrargyrite have been identified in mill products and hence these are suggested as the principal third silver carrier(s) accounting for 13 to 20% of the silver in Brunswick ore. About 24% of this third silver carrier assemblage is lost to the zinc concentrate and 52% to concentrator tailings.

Jan 1, 1984

By E. T. Dumble

DuriKg explorations made for the Pacific Improvement Company in the early part of this year, deposits of natural coke, of such extent and excellent quality as to be worthy of record, were found in the Santa Clara coal-field. This coal-field lies in the neighborhood of La Barranca, a small town, 95 miles northeast of Ortiz, on the Sonora railway. The coal-beds are exposed in the drainage-basin of Calera creek, which empties into the Yaqui river opposite Toniche; and the old mining town of Turahumari is nearly at the center of the field. Without going into a detailed geological description, it Will be sufficient to say that the entire area is underlain by rocks of Triassic age, much disturbed in places, and cut through and covered by eruptive rocks of various kinds and ages. The coal-beds occur in a series of interbedded sands and clay, in the upper half of the sedimentary Triassic rocks. Below them is a great series of quartzitic sandstoiles and very sandy slates, and above them are other sandstones, and the eruptive member of the group, viz., the Lista Blanca formation', described in my paper on the " Geology of Sonora," presented at the New York Meeting of February, 1899.* Speaking very broadly, these sands and clays, with their included coal-beds, dip about 30 degrees S.E. This gives their outcropping edses a 3J.E.-S.W. direction. The general dip

Jan 1, 1900

By Alvin Kaufman

At the turn of the century the U.S. had a gross ALVIN KAUFMAN Mineral Economist U.S. Bureau of Mines area slightly in excess of three million square miles, a population of 76 million, a gross national product of $37 billion (constant 1929 dollars) and a mineral production valued at $2 billion (1929 dollars). Some 60 years later its area had increased by 600 thousand square miles, population had risen 140%, gross national product was seven times greater and mineral production had grown to a value five times that of 1900. Of perhaps greater significance, however, were the changes wrought by technology. It was during this period that the "American Way of Life" was revolutionized by the introduction of the airplane and the automobile; man also took his first probing steps in the utilization of nuclear energy and pre- pared to unlock the secrets of space. It was during these six decades, also, that he learned to create additional new materials, some of which were from old sources such as plastics from petroleum and coal. These new materials have created competition and attendant problems for the traditional materials such as iron, copper, lead and zinc. Additional problems undoubtedly will be created by technologic advances in the future.

Jan 2, 1963

By Richard T. Newcomb

Federal and utility industry research has largely ignored coal beneficiation techniques in the implementation of SOx control. This paper accepts the hypothesis that beneficiation cum scrubbing is the cheapest way for the vast majority of seams in the eastern coal provinces to comply with standards. Comparisons are based on point estimates of average beneficiation costs from a model of coal preparation (COBET) designed to simulate four levels of cleaning. The paper describes how economic theory can be applied to derive econometric supply functions from actual data on the geology of minable seams, washability and technical constraints. West Virginia is taken as an example of a producing region. Spatial supply functions are derived empirically from the engineering model simulations.

Jan 1, 1977