Search Documents

By B. J. Steblay

Roof bolts are the primary means of supplemental support in coal mines and are widely used in other mines. Presently, post installation loads are measured infrequently on only about 10% of the bolts by using standard torque wrenches that limit accuracy to about ± 30%. Because mine roof bolts are long, slender, non-uniformly sized, roughly forged, placed in a difficult environment, and subject to severe bending on installation, researchers have been unable to use ultrasonic reflection techniques to measure strain. A complete measurement system has now been assembled by the US Bureau of Mines, Denver Research Center. Obstacles such as bolt preparation, transducer mounting, reliable reflection, and calibration have been dealt with. The seemingly simple concept of measuring the time of flight of an ultrasonic pulse to a reflector is actually complex due to the need to measure to 0.0025 mm (0.0001 in.) accuracy, the sensitivity of velocity to temperature, and stress, and the stability required to make measurements over several years.

Jan 1, 1986

By R. F. Pilgrim

A digital computer program to mathematically simulate the effect of limited changes in feed rate in the range of 80 to 95 tph on a plant-scale wet grinding circuit has been developed and tested. The circuit studied included an 8-ft-diam X 12-ft rod mill operating in open circuit and feeding two parallel 12-ft-diam x 10-ft pebble mills, each one operating in closed circuit with an 8 X 32-ft rake classifier. The simulation is an empirical one based on two sets of data collected manually from the operating circuit under what was said to be steady-state feed rates of 80 and 95 tph with all other operating variables also at steady state. The procedure is a combination of several published approaches to the modeling of grinding mills and classifiers and it is applicable to a wide range of circuits. The program permits the computing of the size distributions of all feeds and discharges of all grinding units and classifiers in the circuit for a specified feed rate. The data used in this report for demonstrating the program are unsatisfactory since the circuit was not operating under steady-state conditions when it was sampled. Consequently the circuit model parameters could not be accurately estimated. The predictive power would be greatly improved if new data were obtained under true steady-state conditions.

Jan 1, 1973

By Richard A. Brown

The direct precipitation of uranium with hydrogen peroxide has been known since 1877. Commercial use of the process began in the 1960s. During 1967 the US Bureau of Mines (USBM) assisted the Climax Uranium Co., Grand Junction, CO in the development of a uranyl peroxide precipitation process to control a molybdenum impurity problem (Shabbir and Tame, 1978). Atlas Minerals, Moab, UT has used hydrogen peroxide to control vanadium and sodium levels in uranium concentrates since 1969 (Caropresso and Badger, 1973). Recently, the use of hydrogen peroxide by the uranium industry has grown, particularly since the increased demand for uranium has led to the processing of low grade ores. Impurities present in low-grade ores can be concentrated with the uranium during milling and will substantially complicate the refining of uranium yellowcake concentrates. Consequently, commercial nuclear fuel processors have imposed stringent specifications and penalties to control these impurities. The ability to produce a pure uranium yellowcake can eliminate penalty or reprocessing costs. Hydrogen peroxide precipitation of uranium is specific and quantitative, producing a very high purity product. Although the hydrogen peroxide precipitation of uranium has, and continues to be used primarily as means of producing a high purity yellowcake, it has also become an important process due to the superior physical properties of the precipitate. Under normal operating conditions, the precipitate produced by the reaction of hydrogen peroxide and uranium is dense, easily filtered and dried. The final dry yellowcake is pure, high U308 assay product. Consequently, processing costs such as filtering, drying and/or calcining and drumming, can be reduced compared to ammonia, caustic or Mag-Ox precipitation.

Jan 1, 1982

By L. P. Teas

The main facts brought out by the study of the blende-bearing ores examined are as follows: 1. Chalcopyrite as minute triangular or rectangular dots, or as

Jan 1, 1918

By Joseph R. Crump, Francois Ville, Frank M. Tiller

Several simplifications have been accepted in filtration theory during the past fifty years in an effort to avoid apparently intractable mathematical problems. In effect, these simplifications ignored the variation in average cake porosity and average filtration resistance with variation in pressure drop or with time. This study examines the traditional approach and shows that, in many cases, it cannot give correct design guidance. Using a set of dimensionless parameters because of the large number of significant variables, a revised theory is developed which does not require that porosity and resistance values be set constant. Graphs developed in the traditional approach (e.g., dt/dv versus v or t/v versus V) have substantial curvature near the ordinate; but this curvature is frequently ignored in theory and is easily missed in experiments. The revised theory allows more accurate design calculations, especially for compressible cakes.

Jan 1, 1980

Dubbed "Freeport's Mission Impossible" by the trade press, the company's Ertsberg mine in West Irian nevertheless shipped its first concentrates in December 1972, ahead of schedule. This is a new and great chapter in the history of Freeport Minerals Co. and its contractors. Exploration and construction were only possible by moving equipment and supplies by helicopters. This work was carried out by Petroleum Helicopters, Inc., of Lafayette, La. At the peak of operations six machines were in service manned by 11 pilots and supported by 10 mechanics. During the month of August, with work in full swing 1,604 tons were moved, including 3 DC-6 tractors requiring 18 trips each; flying hours for the month were 636.

Jan 1, 1973

By J. M. Bugbee

THE engineer and the conservationist agree that effective water drive is the desirable reservoir production mechanism. Water drive may result either from the expansion of edge water, the reservoir water bordering an oil pool, or from the artesian flow of edge water from the outcrop. Thus, the extent of the reservoir has an important bearing upon both the rate and the ultimate quantity of water influx to an oil pool. Lens-type reservoirs are generally recognizable, but the complete structure of the more important domal types, having possible limitations from crestal and synclinal faulting, is not well understood. The delineation from cores, electrical logs and exploitation phenomena of the crestal portions of reservoirs is increasingly exact. This paper suggests that inference from these factual pictures, combined with the scattered well and geophysical data of the synclines and with consideration of the dynamics of structural formation, may be applied to solving the complete geologic structure. Since faulting on the domes and in the synclines may effectively seal and thus limit the size of a reservoir and bar additional water influx, consideration of geologic structure and its possible effects is essential to complete analysis and prediction of reservoir performance.

Jan 1, 1942

Hunkered up against the spine of the Andes in a tight valley where natural refuge from avalanche hardly exists is the daring Rio Blanco project of Cerro Corp. The deposit here was found in 1904, but nature has foiled all previous attempts to open it. To an experienced mountaineer or a highway engineer with mountain experience, the avalanche hazard in the valley of the Blanco river would be immediately apparent. The collar shaft is at the head of the valley at an elevation of 3600 m and for 12 km down the valley there is no space on the floor for building very much; the dissected rock walls are roadways for avalanches and even a highway could not be maintained sufficiently passable. This is the proposition taken on by the Cerro Corp. Chilean National Decree #1699, passed on December 9, 1966, signified "Go" to the Compania Minera Andina, a company whose shares are held 70% by the Cerro Corp. and 30% by the government of Chile. The orebody, although only partially delineated, contains proven reserves of 120 million tons of ore averaging 1.58% Cu. When the operation comes on stream in the last quarter of 1970, it will be at the rate of 11,000 tpd. Annual production will be 65,000 tpy of recoverable copper in concentrates.

Jan 11, 1969

By Donald E. Crowell

In the fall of 1969, ASARCO and Newmont Mining Co. began the design of the 700tpd concentrator at their Black Cloud shaft located near Leadville, Colo. The concentractor would treat by flotation a Pb-Zn-Ag ore containing minor gold values. Flowsheet design was based on laboratory test work performed at the Minerals Research Testing Laboratory of ASARCO. Since the concentrator is located at an elevation of 11,000 ft, cold weather was a major factor in design considerations. The original capacity was designed as 700 tpd but for various reasons an ultimate capacity of 1,000 tpd was desired. This necessitated special consideration in the design of several areas, particularly the grinding circuit. The grinding circuit chosen was a single 9 X 12 ball mill operating in closed circuit with one 20-in. cyclone. The ball mill will operate at low speed and as an overflow type originally. The mill can be speeded up and converted to grate type for handling the larger tonnage when required. Thickeners and filters were oversized and space was left for additional flotation cells in order to handle the increased tonnage in these areas. Pumps were sized so that they could handle the increased tonnage by increasing their speed. Construction began in May 1970; the Black Cloud concentrator went on-stream in April 1791.

Jan 1, 1974

By R. W. Raymond

The idea of obtaining light from incandescent solids is not new; nor is it. new to make such bodies incandescent by holding them in a heating flame. But the successful combination of the right substance and form of the body to be heated with the right kind of flame and the right means of adjustment, has not, to my knowledge, been accomplished heretofore; and it seems to me that the matergas incandescent light of Mr. Otto Fahnehjelm of Sweden, in which these objects appear to have been secured, is destined to become both famous and useful. The first fact upon which this invention is based, is the intense

Jan 1, 1885

By P. S. Katval

It is interesting to note that an attempt has been made to rationalize the effect of prestrain on the strength of Hastelloy X-280 after various aging treatments. However, two points raised by the authors seem to be somewhat unclear. 1) Concerning their Fig. l(a), the authors state: "Extensive dislocation networks are still in evidence. The 24-hr aging at 1500°F and the 15-min soak at 1350°F did not eliminate the dislocations introduced by the 20 pct cold reduction." This is, of course, to be expected since complete "elimination" of dislocations would require recrystallization which does not occur at 1500°F in Hastelloy X. However, recovery

Jan 1, 1969

By S. R. Krogh, T. O. Olsen

Analytical expressions for the breakage rate as functions of mill charge, mill speed, particle size, ball diameter, and ball load are derived, using idealized models for probability of breakage (Gaudin and Meloy), energy distribution (Mempel), and arithmetic mean of effective ball energy (Langemanns). Computational results using the theoretical equations are compared to experiments. The equations enable simulation of ball mill grinding at different grinding conditions.

Jan 1, 1973

By T. Prof. Egleston

IF we may characterize the aim of metallurgists twenty years ago by any one point towards which their efforts were especially directed, we should say it was the idea of adapting "waste products" to some useful purpose, while the energy of to-day seems rather to take the direction of so arranging processes as to have no " waste products." The iron-master of this decade no longer speaks of the waste gases

Jan 1, 1873

By Charles L. Elliot

Data on worldwide geophysical activity in application to mining exploration programs is collected annually as part of a continuing service to the mining and petroleum industries. The data for mining geophysical activity in 1966 has been made available to SME by the Society of Exploration Geophysicists. This data is based on 288 voluntary responses for a return of 59% to 487 questionnaires that were circulated among worldwide mining companies, universities, and government institutions that conduct or utilize mining geophysical surveys or carry out allied research efforts. This data is herein published in condensed form with the permission of the SEG.

Jan 11, 1967

By W. B. Mather

Literature dealing with rock drilling presents a mass of conflicting data. The principal cause of the confusion is attributed to varying definitions of the hardness factor of rock and cutting media. The future development of more efficient drilling methods demands that this problem be solved. The first step in the solution is the compilation of complete data on the physical properties of rocks.

Jan 2, 1951

By V. K. Karra, A. J. Magerowski

An overview of the scope of a computer program meant for aiding the design of crushing circuits is presented. Effect of circuit variables like the screen separation size and the crusher setting is illustrated. For a better understanding of the logic behind the circuit sizing, a detailed commentary in the case of a starting example is given.

Jan 1, 1982

By C. S. Witherell

THE first feature that strikes one when considering the use of air enriched with oxygen in pyrochemical processes is the conservation of Enriched Air FIG. 1.-TEMPERATURES THEORETICALLY OBTAINABLE BY BURNING PURE AMOR¬PHOUS CARBON IN AN ATMOSPHERE COMPOSED OF AIR ENRICHED WITH OXYGEN, PRODUCING GAS CONTAINING CO. heat due to the partial elimination of the inert heat-carrier nitrogen, as set forth in the report of the committee. The second feature, which

Jan 11, 1924

Jan 1, 1952

By A. A. Archer

Marine mining is here defined as the commercial recovery of minerals other than oil and natural gas from the surface of, or below, the seabed by operations connected only indirectly with the land. The number of operations falling within this definition and the number of countries involved are remarkably limited in view of the widespread interest shown in marine mining prospects during the last few years. Marine mining is still restricted to continental shelves, where the only superficial minerals currently being mined are sand and gravel, calcium carbonate in different forms, and tin and iron sands.

Jan 12, 1973

Member ship L P MATHEWSON, Chairman GEORGE D BARRON LOUIS D HUNTOON JOHN A CHURCH, JR H N SPICER Alternates LEWIS W FRANCIS WILBER JUDSON F T RUBIDGE Increase of Membership JOHN A CHURCH, JR, Chairman Other members to be appointed

Jan 1, 1923