Search Documents

By William B. Stephenson

IN the pumping of sands, slurries and slimes, practices developed over the years are the real keystones of successful operation. These practices are necessarily based on modifications of familiar theories. Practical methods used in the solution of problems involving the pumping of materials are set forth in the following discussion. BASIC REQUIREMENTS To pump sands and slurries economically, a few basic requirements must be met by the pumping system as a whole. A pipe-line velocity must be established that will move the fluid mixture throughout the entire system without any possibility of the solids settling out. To accomplish this, the velocity of flow must be slightly in excess of the critical velocity of the mixture. The critical velocity of a mixture varies from 3 ft. per sec. to 18 ft. per sec., depending on the screen analysis, concentration, and specific gravity of the solids in the mixture. Most tailings are pumped at a minimum velocity of 4 ft. per sec. if they include slimes, whereas the pipe lines of sand and gravel dredges require velocities as high as 18 ft. per second. A number of articles have been written on the determination of the minimum velocities required to maintain solids in suspension. Studies have also been made on the friction and pumping heads developed when handling solids in suspension.1-4 Our experience so far has shown that, within the normal operating limits of a pumping system, the friction factor follows more nearly the basis described by Howard,1 who says, among his conclusions: " ... values of ƒ (friction factor) .. . will decrease with an increase in velocity." This conclusion is borne out by our actual experience. When the velocity in a pipe line is not sufficient to keep the solids in suspension, the total friction head is greater than when the velocity is increased to a point where the solids are in suspension. A slight increase in the volume of feed to the pump and a slight increase in the pump speed are usually all that is necessary to put the system in balance. MAINTAINING CONSTANT VOLUME Within reasonable limits, the volume of mixture to be handled through a pipe line should be held constant, so that the required velocity will be provided at all times. There are several ways in which this can be accomplished. The commonest is to provide a sump of sufficient capacity to take care of slight surges in the volume of mixture being fed to the pumping system. This sump, however, should not be as large as a settling chamber. The use of a float-controlled, fresh-water make-up valve in a sump will guarantee a constant volume. Where variations in volume are slight,

Jan 1, 1946

By Charles S. Robinson

The Henderson ore body is east of the Continental Divide in the Front Range of the Colorado Rocky Mountains, about 80 km (50 miles) west of Denver. The ore body is being developed for mining by workings that extend more than 1100 m (3500 ft) below the topographic surface. During construction of the mine workings, ground water in fractures in cystalline rock has been encountered. From 1969 to 1973, Charles S. Robinson & Associates, Inc., in cooperation with the engineering and geologic staffs of the Climax Molybdenum Company, a division of Amax Inc., studied the ground water geology of the Henderson mine development area. Detailed geologic record( of the Henderson mine were available as a result of the exploration, evaluation and development of the mine. Records of the flow, chemical composition and temperature of the ground water at and near the surface, from the entire mine, from portions of the mine, and from exploration holes drilled in the mine, were kept as the mine was developed. Where possible, ground water pressures in drill holes and changes in pressure with time, were recorded. The geologic, hydrologic and chemical data were correlated. The following conclusions were drawn from the correlations: The ground water in the Henderson mine occurs in fractures in Precambrian igneous and metasedimentary rock and in a series of Tertiary intrusive rocks. Two zones of ground water were recognized; an active zone, in which the fracture systems are recharged and discharged annually into the surface water system, and a passive zone, in which the fractures were filled with water in the geologic past. Discharge from the passive zone is through mine workings that intersect the fracture systems. Discharge from a fracture or fracture system is initially high but decreases with time. The rate of decrease in flow (or pressure) is exponential. By measuring the change in flow with time, it is possible to calculate the amount of flow at some given period of time in the future. Based on changes in rate of flow and pressure, and the geology, and assuming rates of mining of the ore, it will be possible to predict the volumes of water that will have to be handled during the life of the mine and the area around the mine that will be drained by the mining operation.

Jan 1, 1979

GENERAL GEOLOGIC DESCRIPTION The mineral deposit of this case study can be described as a "typical" porphyry copper deposit of the southwestern USA and northern Mexico mineral province. The copper mineralization is related to Laramide age intrusives of intermediate composition which have been intruded into older, mostly crystalline, host rocks. Post Laramide deformation and faulting have subjected the deposit to erosion, leaching, and enrichment processes, which have created a secondarily enriched chalcocite zone. Later basin and range faulting down dropped the ore zone, resulting in deep burial beneath late Tertiary conglomerates and gravels, thus preserving the deposit from further erosion and oxidation. Lower grade chalcopyrite mineralization constitutes the primary zone underlying the enriched blanket. MANAGEMENT OF SAMPLE DATA Sample data were obtained from exploration diamond drill holes that were collared vertically and drilled with surface rigs. Most of the holes were surveyed downhole and found to deviate significantly from the vertical. The data were keypunched from original drill hole logs to formats as described in Chapter 6. Three types of cards were prepared: 1) A heading card containing the following information: [Project Name Coordi-in_ Hole Collarnates Bear-clina-Total ID Northing Easting Elevinglion Depth] 2) Individual record cards following each heading card with the following information: [SampleMin. Zone interval Assay Fields Leached (enriched ID From-ToTotal Cu Oxide Cu primary)] 3) Where downhole survey data were available, a card was punched for each downhole survey point. The card image looked very much like the heading card, followed immediately after the heading card, and contained the following information: [Hole Sur Point Sur Point Sur Point ID Bearing Inclination Depth] The keypunched data were then processed by the drill hole survey program producing a record file which contained information as follows: [Line 1. Project Name Date Assay Field Identifiers Line 2. Hole ID Northing Easting Elevation Bearing Inclination Number of Samples Line 3 through N+ 2 (where N equals the number of samples in the hole) Top Min. of Min. Zone Zone Sample Sample Coordinates Sample Assays Leach InterLength Northing Fasting Elev Total Cu Oxide Cu (etc) face] MINERAL BOUNDARY PROBLEM AND TREATMENT According to the geologic description, at least three mineral zones are present within the ore limits, as well as fault boundaries and a buried topographic surface, each of which have to be considered. The interfaces of the various mineralogical and geological boundaries were identified as accurately as possible in each drill hole by the project geologist, the location of the interface was surveyed in the computer program in association with the nearest sample intercept to the interface (note last field of line 3). Thus, the boundary is represented as a point in 3D space at each intersecting drill hole. The linear interpolation (LINTERP) program then searched the last field of the surveyed record to find the top of each mineral zone, or geologic boundary, and read the coordinates associated with that sample point. The program then used the coordinates to compute an interpolated surface between all existing data points as described in Chapter 11. A contour map was plotted for each of the computed surfaces and reviewed by the project geologist. Where the surfaces were poorly defined due to lack of real drill hole information, the geologist, at times, inserted a "pseudo" drill hole intercept according to his best judgment and feeling for the configuration of the surface, and such points were entered into the data stream for LINTERP. When the project geologists were satisfied that they had obtained

Jan 1, 1980

By J. S. Marsh

The student of steelmaking is all too well acquainted with the fact that in many instances he must deal with data that in graphical representation exhibit the property most desirable in bird shot. This is scarcely mystifying, since the effort to establish one variable as a function of another is usually hampered by the simultaneous operativeness of two or three other factors that may be important. A large part of arriving at relationships that have the pleasing self-consistency of, say, precise measurements of thermal expansion, consists of determining what factors must be held constant-—an even larger part usually consists of collecting data for which those factors have been so maintained. It is not intended to imply that functional relationships in the physical chemistry of steelmaking are hopelessly obscure; on the contrary, it is merely necessary to be undisturbed by marked deviation of some points from a curve that otherwise makes sense. A reaction mechanism suggested by such a curve may call attention to hitherto unsuspected factors operative in the origin of the deviating points, and thus permit another step to be taken in the direction of fuller understanding. It is proposed, therefore, to suggest several empirical relationships. Even though the approach is not always rigorous, deviations caused by simplifying assumptions appear to be too small to obscure a provisional It has been appreciated for some time that the carbon-oxygen reaction in liquid steel is highly important. For example, Körber et al.,' in introducing a summary of their extensive work on steelmaking reactions, said: "... the far-reaching and truly dominating action of carbon upon the metallurgical reactions will be especially stressed ..." In "Basic Open Hearth Steelmaking"2 (hereafter BOHS, for simplicity), it is accepted repeatedly that the various slag-metal interactions are nearly always controlled by the carbon-oxygen reaction. Before further discussion of this reaction, however, it will be worth while to consider briefly the carbon-oxygen equilibrium. In BOHS (p. 483) it is stated that: When liquid iron is brought into contact with gases containing carbon monoxide it absorhs carbon and oxygen. Conversely the carbon and oxygen in the metal unite to form carbon monoxide which is evolved from the bath during the open-hearth boil or while rimming ingots are solidifying. . . . When the equilibrium pressure is one atmosphere the equilibrium-constant equation simplifies, on the assumption that the activity of each element is equal to its percentage, to a constant which has been so much used that it has acquired a special symbol m. where m = %C X %O

Jan 1, 1945

Apparatus and a method for determining the volumetric behavior of hydrocarbons at pressures up to 10,000 psia and at temperatures between 0° and 460°F are described. The equipment is suitable for measuring the total volume of the system and the volume of a liquid phase as functions of state within these ranges of temperature and pressure. Introduction During the past two decades there has been a marked increase in the ranges of temperature and pressure encountered in underground hydrocarbon reservoirs of commercial interest. In addition, greater interest in the intensive characteristics of the fluids found in these reservoirs has developed. Apparatus Several types of apparatus have been developed in the authors' laboratory for volumetric measurements of hydrocarbon systems. The earliest equipment described1 was characterized by constant volume, and the weight of material present was varied systematically in order to attain the different pressures desired in the study. Later another apparatus2 was built in which the effective volume of the cylindrical cell, which confined a hydrocarbon sample of constant weight was varied by injection or withdrawal of mercury. The effective total volume of the equilibrium cell was measured by ascertaining the position of the mercury surface but no measurement could be made which gave knowledge of the volumes of individual phases existing within the hydrocarbon system. A third apparatus3 was designed for use at higher pressures and temperatures than the earlier equipment would tolerate. This apparatus was of the variable volume type but was built in the general form of a U-tube, the mercury level being measured at the surface which was not exposed to the hydrocarbon system. This arrangement avoided the need of subjecting measuring equipment to the extremes of temperature at which studies were made, but it gave no provision for measurement of the volumes of individual phases. Although this last apparatus was satisfactory as to accuracy and convenience for many purposes, need was felt for measurements of the volume of the liquid phase of the hydrocarbon system. For this reason a fourth equilibrium apparatus was designed and constructed, and it is the purpose of the present paper to describe it. The equilibrium cell has a working range of temperature from 0° to 460°F at pressures up to 10,000 psi. Provision for measurement of both total volume and liquid-phase volume makes it particularly suitable for the equilibrium study of heterogeneous systems consisting either of simple mixtures or of complex field samples of hydrocarbons. The general arrangement of the ap-

Jan 1, 1948

By Marston G. Fleming

CRITICAL pH has been defined by Wark1 as that pH value below which a mineral will float and above which it will not float in solutions containing a given concentration of collector but free from other depressants or activators. - The relationship between mineral, collector concentration, and pH is expressed in the form of a critical pH curve determined by the captive bubble method and is generally regarded as being fundamental to the system involved. The mechanism of alkali depression is currently in dispute, two general theories having received authoritative support. The view expressed in Taggart's chemical theory of flotation2 is that in the presence of a critical concentration of hydroxyl ions, all the metal ions available at the surface of the mineral are present as anions of the form [M (OH)x]-y. The formation of the necessary metal xanthate is thus precluded and, furthermore, any metal xanthate coating previously formed, at a lower pH, will be dissolved. Gaudin3,4 and the Melbourne school under Ware hold that alkali depression is caused by the preferential adsorption of hydroxyl ions by the mineral surfaces. This paper describes an investigation of the mechanism of alkali depression in each of the three systems: cerussite-aqueous carbonate-xanthate, cerussite-xanthate, and galena-xanthate. Alkali Depression of Cerussite by Control of Carbonate Ion Concentration Wark and Cox6 have shown that in the presence of Na2CO3 a higher concentration of xanthate is required to effect bubble contact with a cerussite surface than in carbonate-free solutions. To examine this depression of cerussite by sodium carbonate, a series of captive bubble tests was carried out on cerussite specimens in solutions containing 100 mg per liter of potassium ethyl xanthate and varying concentrations of sodium carbonate. The pH was adjusted by the addition of dilute hydrochloric acid. For purposes of comparison a standard critical pH curve was determined for cerussite with potassium ethyl xanthate in solutions containing no added carbonate. In the latter case pH adjustment was made with sodium hydroxide. The experimental method employed in both series was broadly similar to that described by Wark and Cox;7-9 a number of refinements suggested by Sutherland10 were adopted, and the procedure was further developed and modified to suit the particular requirements of the investigation. The relationship between pH and the concentration of potassium ethyl xanthate necessary to induce bubble contact at cerussite surfaces is shown in Fig. 1. The relationship between pH and the concentra- [ ] tion of sodium carbonate necessary to prevent bubble contact at cerussite surfaces in the presence of 100 mg per liter of potassium ethyl xanthate is shown in Fig. 2. Comparison of the. two curves shows that at a collector concentration of 100 mg

Jan 1, 1952

By J. Fred Johnson

COROMANT is the trade name of the alloy-steel drill rod tipped with a chisel-type tungsten-carbide bit manufactured by Sandvik Steel Works Co., Ltd. Other names, such as Swedish or air-leg method of drilling, are used in various localities. Coromant drilling in Sweden was the natural sequence of the adaptation of tungsten-carbide inserts to the already established routine of drilling. By the middle thirties the percussion drill had reached practically its highest attainable efficiency as a drilling machine. Since then improvement has been in metallurgy of component parts to increase life or lessen weight, in the development of pneumatic and automatic feeds, in the use of jumbos to more quickly and easily handle machines, and in changes in drill rods and bits. By 1937, drilling in the United States and Canada was done by relatively heavy mounted drifters with positive hand or automatic feeds. In Sweden, on the other hand, emphasis had been placed on light equipment and drifting was done with pneumatic bars and reverse-feed stopers. In 1938, one of the most prominent American drill manufacturers developed an air-leg for successfully drilling the extremely variable but relatively soft iron ores of some of the northern Michigan mines. Also in 1938, a comparative Swedish test, also in soft iron ore, of a 50-lb jackhammer mounted on an air-leg, against a 100-lb reverse-feed drifter on a pneumatic bar, showed the net drilling time was increased by the air-leg set-up from 51 to 71 pct, in drilling 6-ft rounds in a 6 1/2x6 1/2 ft drift. Miners were becoming scarce in Sweden even at that time and, since the lighter equipment made the work easier and more attractive, the airleg was then made use of in some types of soft rock. In 1940, for instance, a large tunnel for a hydroelectric plant was driven with this equipment. By 1943, when tungsten-carbide inserts came into the picture in Sweden, a great many of the kinks in percussion drilling with this hard-metal had been worked out in Germany under the stress of war conditions. However, only 10 pct of the drilling machines manufactured in Sweden were jackhammers for use on air-legs and only the one manufacturer made air-legs in the United States. American practice had largely supplanted integral forging of drill bits by the detachable steel bit. Canada and South Africa were using the one-pass throwaway bit but Sweden was still using the same old integral forged bit. After a long study of the trend toward simplicity

Jan 1, 1952

By Oliver Bowles

Slate is a fine-grained rock that has a more or less perfect natural cleavage, permitting it to be split readily into thin, smooth sheets. According to a definition established by the American Society for Testing Materials, slate is "a microgranular crystalline rock derived from argillaceous sediments by regional metamorphism and characterized by a perfect cleavage entirely independent of original bedding, which cleavage has been induced by pressure within the earth." Origin and Character Slates have originated from sedimentary deposits consisting largely of clay. Such materials were carried by streams and deposited in seas or lakes in successive horizontal beds. Other materials such as calcium carbonate, sand, or gravel may have been deposited over the clays, and the pressure of these superimposed materials gradually consolidated the materials below into bedded deposits of shale. Shale is a stratified rock formed by recrystallization of the clay plus adsorbed potash into the mica, sericite. Shale has neither the strength nor the splitting properties of slate since the mica is fine and the flakes unoriented, and the quartz grains do not interlock. Many shales, however, have been subjected to intense metamorphism. Mountain-building forces ever at work in the earth's crust may crumple, squeeze, and fold the shales. At the same time, accompanying high pressures and temperatures changed the original minerals into mica, interlocking quartz, or chlorite. Both mica and chlorite consist of minute tabular sheets or flakes with perfect cleavage. The intense pressure and movement tend to orient these flakes in parallel positions normal to the direction of pressure. The parallelism of the flakes results in the tendency to split with ease in one direction, which has been termed "slaty cleavage," and which is the outstanding characteristic of slate. Actually, the cleavage is through the cleavages of the individual micaceous plates. The original bedding of the slate is often folded and contorted, and the slaty cleavage commonly cuts across it at sharp angles. Composition MINERALOGICAL COMPOSITION The most abundant mineral in most slates is white mica (sericite), a hydrous silicate of potash and aluminum. It is present in very small flakes recognizable only with a microscope. Small grains of quartz (silicon dioxide) are also abundant and are regularly distributed among the mica flakes. The mica-like mineral, chlorite, is usually present in considerable quantities. Chlorites are of several kinds, the more common being hydrous silicates of aluminum and iron or magnesium. Other common minerals present in small quantities are rutile, clay, hematite, pyrite, carbonaceous matter, feldspar, zircon, tourmaline, calcite, dolomite, and siderite. The general range of the chief constituents is about as follows: Sericite, 38 to 40; quartz, 31 to 45; chlorite, 6 to 18; hematite, 3 to 6; and rutile, 1 to 1 ½ pct. CHEMICAL COMPOSITION Results of many analyses indicate that clays, shales, and slates differ little in chemical composition. The changes that take place during metamorphism are confined largely to rearrangement of the elements into new minerals with accompanying changes in physical properties such as hardness and cleavage. The general

Jan 1, 1960

By F. O. Garrabrant, F. S. McNicholas, Robert Henderson, R. U. King

Several years ago, it was decided to experiment with the use of high-pressure water to bring in finger hangups and reduce the amount of secondary blasting necessary. It was argued that the velocity effect of the high-pressure water would bring down hangups without unduly wetting the ore. Water under a head of about 550 ft. was installed in certain slusher drifts. Ordinary ¾ in. water hose, with a nozzle opening of % in., was used, and water was impinged on the fines under a hangup. Results were excellent. About half the total number of hangups were brought in with high-pressure water without blasting and the cost of this part of the slushing operation was reduced about 50 per cent. Operations were speeded up, dust counts and safety hazards were reduced, and a more desirable working place was secured. The additional water added to the ore was under one per cent and caused no inconvenience in slushing, haulage, or crushing operations. Usually the ore would absorb all of the water, so that none of it would enter the loading drifts. The entire mine, developed by slusher drifts, is being equipped with high-pressure water. Heating Mine by Compressor Cooling Water Several years ago, the problem of heating certain sections of the mine during freezing weather became important. It was calculated that there was sufficient heat in the compressor cooling water to heat the incoming ventilating air current to above freezing, if such heat could be transferred from the water to the air. All schemes of radiation from pipe were rejected as too cumbersome, costly and impractical. It was thought that by spraying the heated water from the compressor cooling system into the incoming air, a satisfactory heat exchange could be accomplished. The only objection was that the sprayed water would freeze and might fill the air-intake drift. However, when water at about 75° to 80°F. was sprayed at the rate of 200 gal. per minute through a bank of sprays into the incoming and freezing air current, this air was thereby heated to above freezing; and although some ice was built up in the air drift, the amount was not objectionable. Occasionally the built-up ice was picked down into the outgoing water stream, which removed it. The entire south and westerly parts of the mine were prevented from freezing. Concreting for Hangups Considerable trouble was experienced in securing hangups of fine ore in slusher fingers that needed repairing. Regular methods of timbering were unsatisfactory. Now, a slab of concrete is poured over the top of the muck by Pumperete machine, almost filling a finger, which gives a satisfactory slab to work under for making the needed repairs. Derailers Some trouble has been caused by motor-men not observing safety lights and

Jan 1, 1946

By G. Koves

The behavior of case-hardened AISI C-1213 free -machining steel under complex impact-fatigue -wear load conditions was investigated. The inherently poor dynamic properties of the steel are mainly affected by the stress distribution in the case, component shape, and tempering. Cold-riveted components showed unexpectedly high dynamic strength compared to basic parts. A compromise beatment—which provides good dynamic properties, reasonable wear resistance, and fair riveting characteristics—zuas developed. A number of mechanical components in data-processing machines are made of free-machining carbon steel. Although, selected primarily due to manufacturing requirements, components made of these grades frequently undergo complex heat treatment and must sustain impact-fatigue loads. A typical free-machining steel is the AISI C-1213 grade, which is a resulfurized and rephosphorized open-hearth steel. While the undesirable effects of sulfur and phosphorus on the mechanical properties are well-known, data on dynamic properties are scarce.1"3 Rapid rotating or oscillating motion while carry- ing a high cyclic load requires a combination of wear resistance with high endurance limit and impact toughness. The inherently poor dynamic properties of the free-machining steel are further degraded by the machining, which introduces local stress-concentration areas. While the heat treatment (usually case hardening) improves some mechanical properties, it necessarily impairs others. Another problem arises when components, such as studs, must be fastened by riveting. The high crack-sensitivity of the free-machining steel, especially in the presence of a hardened case, makes this operation difficult. In view of the preceding considerations, it is of interest to investigate the behavior of a typical component under complex impact-fatigue-wear loading conditions in order to explore the effects of material, machining, and heat treatment, to obtain specific data on the dynamic characteristics of free-machining steel, and to arrive at a process which would adequately utilize the inherent qualities of this material. EXPERIMENTAL PROCEDURE To simulate actual service conditions, a typical component was selected, based on frequency of application, complexity of load, and processing difficulties. The dimensions and shape of the component—a stud used in many electromechanical document-handling machines—are shown in Fig. 1.

Jan 1, 1964

THE primary interest in the subject of this chapter lies in the fact that various heats of steel made to the same chemical specification do not always have the same properties. We are referring here, of course, to properties inherent in the just solidified ingot and are not considering variations in properties caused by variations in subsequent mechanical or thermal treatment. The expression "made to the same chemical specification" is used because some of the variations in properties are due to variations in chemical analysis within the specified ranges of those elements commonly specified and determined. In plain carbon steels these elements are ordinarily not more than five: carbon, manganese, silicon, phosphorus, and sulphur. In alloy steels the special alloying elements also are specified and. determined. It might be thought that variations in properties due to such variations in ordinary chemical composition are to be expected, well understood, and hence not in need of discussion in this chapter. It will be considered here, however, that this phase of the subject is not always wholly clear. Furthermore, it certainly seems profitable to seek the explanation of anomalous properties in the ordinary chemical composition of the steel before looking into less well understood variables of open-hearth practice. It is sometimes surprising to learn that some puzzling variation in properties is caused merely by a variation in the ordinary analysis of the steel. This surprise is apt to be due not to general lack of knowledge of the effects of the composition of steel upon its properties but rather to the fact that we do not happen to have been previously much concerned with the particular property under consideration. For example, if we are accustomed to using S.A.E. 1035 bars for applications which depend chiefly on the stiffness, strength, and toughness of the steel in the as-rolled condition, we might quite logically develop the conclusion that variations in carbon content from 0.30 to 0.40 per cent are not significant. Then if we later have occasion to make heat-treated bolts of the same grade of steel, we may be surprised to

Jan 1, 1944

By Ernest R. Lilley

While American scientific literature contains much information upon geologic conditions controlling the production of oil in Rumania, copper in Chile, and other fuel and metallic resources in many foreign countries, it is singularly lacking in data about the nonmetallics outside of the United States. Thus, though the United States is the outstanding market for European high-quality refined kaolin, and for the chinaware, porcelain, and other products of the European ceramics industries, American literature contains only the briefest references to the deposits from which the raw kaolin utilized is obtained. To the writer, to whom has come in the past year the opportunity of visiting a number of these deposits personally, they have proved of extreme interest both commercially and geologically. It is the latter phase that is discussed in this paper. The older and now largely crystalline rock areas of France, Germany, and other parts of western Europe contain numerous pegmatite dikes of which the upper portions have been subjected to surface weathering and kaolinization in much the same way as those of the eastern portion of the United States. Like the latter, the European pegmatite kaolins have long been known for their freedom from iron and other impurities offensive to the china and porcelain manufacturer. Unfortunately, they are also, like the American deposits, individually of small size and noted for their high costs of production. Deposits of sedimentary clay similar in many respects to the high-quality sedimentary kaolins of Georgia and South Carolina are known and worked, notably in southern Germany and in the Newton Abbott district of Devon and Dorset in England. In general, their relationship to the parent rock from which they were derived is more evident than in the United States and the individual deposits are of smaller areal extent and less regular in outline. While these deposits are of considerable economic importance they did not, because of their similarity to deposits in America, attract and hold the interest of the writer to the extent that several other types of deposits did. It is to the latter, which are so different from the kaolin

Jan 1, 1932

By Robert E. Thurmond

DISCOVERY of a commercial ore deposit has resulted from a program emphasizing geophysical techniques and concentrating upon exploration of alluvial-covered areas. United Geophysical Co. selected these areas as offering the best possibility of success, for here the surface evidence of ore deposits has been hidden from the eyes of prospector and geologist alike. Pima mining district, Pima County, Arizona, was selected for initial exploration. The project was successful in that a commercial ore deposit was discovered and proved through drilling and extensive underground development. A limited region of activity was chosen and library research was begun on available economic and regional geological publications relating to the mining districts. Field reconnaissance of those districts which seemed to hold exploration possibilities provided a general picture and ascertained the existence of alluvial-covered areas of interest. At the conclusion of the reconnaissance trips all data obtained were compiled, and the district which seemed to present the best exploration possibilities was selected by statistical methods. The statistical summary was based on the following considerations: Geological Factors: 1—type of intrusive, P—presence of favorable host rocks, 3—apparent intensity of mineralization, and 4—presence of favorable structure in covered or unexplored areas. Economic Factors: 1—past production from district or mine; 2—size, shape, grade, and type of ore deposit in the district; 3—ease of acquiring mineral rights; and 4—general development facility. Exploration Favorability Factors: 1—results to be anticipated from geological methods alone; 2—application of geophysical methods, namely, topographic conditions, surface interference, depth-size relation, physical property contrasts as related to ores or controlling structural features; and 3—drilling factors. Admittedly, many of these, factors do not lend themselves to absolute evaluation, but relative evaluation, subject to inaccuracies of personal judgment, is always possible. A relative scale from 1 to 10 was established for every factor, representing varying degrees of favorability. For each district a numerical evaluation of each factor was established and a numerical total determined. The obvious advantage of this scheme is that a more concise summation can be presented by numerical means than can be achieved by descriptive means. After a district had been selected as favorable, the first step was to carry out more detailed geological and economic studies to narrow down the areas of interest. The second step was to compile all available geological data from publications and add to these data by mapping where necessary. Geological interpretation and projection of structural or other control into covered or unexplored areas was made whenever logical. To determine the possibilities of geophysical application and to select a geophysical method, physical property contrasts were related to mineral assemblages and/or structural control. If geophysics seemed applicable, trial profiles were run crossing the area normal to the strike and spaced

Jan 1, 1955

By Seymour Fiekowsky, Alvin Kaufman

Taxes are compulsory charges levied by a government for its support. They are usually paid to support the general services provided by government rather than special services (such as safety inspection). The latter are normally supported by user charges often called license fees. Taxes are used by national governments not only to raise money but also as a part of fiscal policy. As such, taxes are used to stimulate or deflate the economy, as an incentive to save or invest, as a means of allocating national resources, and as a means of redistributing income. In our discussion, we will deal only with those facets of the subject that relate specifically to the mineral industry. In doing so we will deal with taxes levied on all industry in a generalized way and only insofar as it affects our industry, but at some length on those portions of the tax system related directly to the mineral industry. It is not our intent to provide a "cookbook" for computing taxes, but rather to present some of the policy issues that bedevil those who must develop our tax policies. MINERAL TAXES The mineral industry is subject to the full range of taxes levied by governments. These include taxes on income, property, and sales, as well as excise and severance taxes. The latter are somewhat similar to a royalty in , that such taxes are levied either ad valorem or per unit of output. Severance taxes most commonly are charged to oil and gas output, although coal, salt, sulfur, and iron ore production also have been taxed in this manner. The major governmental advantage of the severance tax is the administrative ease of collection. On the other hand, it poses an addition to cost independent of profitability. As a consequence, the severance tax can cause premature abandonment if mineral product prices do not rise sufficiently to cover it. Such a rise may not occur if differential tax rates are levied by the various states. Property taxes normally are levied on all property owners, including mineral owners. The major difficulties in this kind of tax, in so far as mining is concerned, are erratic valuation coupled to the inherent problems involved in assessing a property where the extent and richness is chiefly unknown. The impact of these taxes, including state income taxes, is reduced somewhat, as they are usually deductible from gross income as a business expense with a consequent lowering of national income taxes. The net cost of severance, property, sales, and state or local

Jan 1, 1976

By Ralph H. Sweetser

OF SPECIAL importance in the design and construction of an iron blast-furnace plant are tile raw materials to be employed. Obviously the iron must come from some ore of that metal, but the many kinds available lead to important differences in plant arrangement, and in the design of furnaces and accessory equipment. For instance, the bulk of the gangue in the ore is subject to wide variation as is that of the ash in the fuel. A gradual increase in the bulk of raw material necessary to produce a ton of pig iron has been noted, but this has been more than offset, so far as costs of operation are concerned, by improvements in the machinery used for handling large quantities of ore. coal limestone, and slag. The mechanization of coal and iron-ore mining. the building of big ore boats and limestone carriers, of ore docks for fast loading and unloading, and the general use of heavy railroad equipment have all contributed to greatly reducing the number of man- hours required to mine, transport, and manufacture the raw materials into a ton of pig iron. This looks like a big saving and it is. If it were not for these big labor saving machines it would be impossible to produce the tonnage of iron and steel that is made each year in this country. On the other hand, the total capital investment necessary to bring down the man-hours per ton of pig iron to a 2.3 hours average at the blast furnace and to a total of only 12 man-hours from ore to metal (see Table 1) is so great that even the present high price of pig iron is probably not far above the true cost of manufacture when all the fixed charges are properly included.

Jan 1, 1939

By William B. Senseman

For reasons well known to mining engineers, wet grinding is quite universal in plants having to do with the extraction of metallic values from crude ores. In the processing of the nonmetallic and industrial minerals, dry grinding is the more common method. The crude materials usually contain less moisture than is required for wet grinding and the products usually are marketed in dry form; most of them as powders. To grind wet, therefore, would entail the addition of water and an expense for drying the product, which is not justified. Furthermore, the material would be a dried cake that would still have to be pulverized or disintegrated before use. For producing fine products, air separators have largely replaced the earlier practice of sizing with screens and bolting reels. Mills in which the air-separating feature is an integral part of the design are now commonplace. Mill designs are many and air systems have developed along various lines, but for the purpose of this discussion, only the fundamental idea need be emphasized— the idea of using air for sizing and removing pulverized material from a grinding mill. About 20 years ago, when the use of mills equipped with air separation had become common practice, heated air or gas was introduced to such a system for the removal of moisture. The purpose of this discussion is to outline the developments and trends that have followed this experiment. It is an important development, for mills equipped with air separation are now universally used for pulverizing not only nonmetallic and industrial minerals, but a great variety of other materials. All such mills are essentially the same. Dried material is pulverized, removed by an air stream, trapped in a cyclone collector, and relatively clean air from the cyclone is returned through a fan to the mill. There is no theoretical need for a vent from the system. The practical need is to vent the air that leaks into the system, and, since the cyclone is not 100 per cent efficient as a dust collector, this vented air carries some dust with it. The initial attempt at drying was made on a system like that described, by the addition of a furnace. The minus pressure within the mill draws hot gas from the furnace. Infiltration air, along with the drying gases and evaporated moisture, is vented as before. The first application was made to a mill used for pulverizing coal. The coal contained very little moisture, so very little drying effect was needed for the success of this experiment. Actually, some calculated efficiencies of over 100 per cent were obtained before due allowance was made for the conversion of mill power into useful heat. When moisture is low, the heat obtained from the conversion of mill power is an appreciable part of that required. That drying can be effected in the short time interval available in a grinding mill of this type is better understood by visual-

Jan 1, 1947

By H. L. Eiselstein, F. P. Huston, B. B. Betty

An extensive program for the establishment of creep data on high-nickel alloys has been in progress during the past seven years. This paper presents the accumulated data on two solid solution alloys, cold-drawn, annealed Monel and cold-drawn, annealed Inconel. Data on these two alloys in other conditions will be published at a later date. Monel, a nickel-copper alloy, is normally considered a corrosion-resistant material, but it will be shown that it also has considerable creep strength, validating its use at temperatures up to and including 900°F. Inconel, a nickel-chromium-iron alloy, is definitely a heat-resisting alloy possessing good creep strength and oxidation resistance up to iiooOF., and because of its oxidization resistance has been used successfully at much higher temperatures for lightly stressed parts. The literature contains but meager data on the creep properties of high-nickel alloys. Howevcr, Bennett and McAdam have presented a substantial quantity of creep data for cold-drawn Monel.1 The material as tested was not representative of mill production for it was cold-drawn to a reduction of area of 40 per cent as against 13 per cent, which is the mill standard for Monel. Twenty-two individual tests were run on each alloy in the investigation described in the following pages. The data and curves presented herein represent an integration of all the tests to obtain the most accurate picture of the creep properties of these alloys. Neither of the two alloys was found to be embrittled by the combination of temperature and stress, as evaluated by room-temperature tensile and impact tests that were made following creep testing. These data indicate that no tendency toward embrittlement exists. It is recommended that 6300 lb. per sq. in. be used as a working stress for cold-drawn, annealed Monel at 900°F. and 13,200 lb. per sq. in. for cold-drawn, annealed Inconel at the same temperature. Table 8 lists recommended working stresses, based on 80 per cent of the stress to produce a minimum creep rate of 0.01 per cent per 1000 hr., for Monel and some steels. Equipment The equipment used for these tests consists of Colville creep-testing machines manufactured by the Tinius Olsen Testing Machine Co. The load is adjusted, depending on the stress level, to give an error in the stress of not more than ± 0.1 per cent. This is based on considerations of lever sensitivity and the stress used for the standard (A.S.T.M. Tentative Standard E22-38T) 0.505-in. diameter creep specimen having a 2-in. gauge length. The single-specimen furnaces are provided with primary and secondary windings, from

Jan 1, 1945

By Pramod C. Thakur

Introduction Methane is contained under pressure within the fractures and adsorbed on the surface of the coal seams and adjacent strata. It is released into the mine atmosphere during mining of the seam creating explosive gas-air mixtures. Large volumes of air, sometimes as high as 20 tons of air for each ton of coal mined, are circulated constantly to dilute and carry away methane from coal mines. Removal of methane from solid coal, wherever high methane emissions occur, has been discussed by Spindler and Poundstone (1960) and Thakur and Davis (1977). Methane control in longwall gobs is much more complicated. As longwall mining progresses, the overburden continually subsides, and the immediate roof caves behind the roof supports. Even the underlying strata heave and open up communication channels feeding gas to the longwall gobs. The pressure of gas in the underlying and overlying strata is usually higher than the ambient air pressure in the mine. Thus the mine workings become natural pressure sinks, into which gas flows from the entire disturbed zone. Winter (1975) defines this zone as the "gas emission space". Depending on the number of gas-bearing zones in the gas emission space and their gas contents, the total methane emission from longwall gobs could vary from a few to more than one hundred cubic meters of gas per ton of mined coal. Hence the ventilation of longwall faces demands a large quantity of air. This ventilation need is further enhanced by high air losses specially on caving faces (with no stowing of the gobs). The old system of longwall ventilation, the 'U' pattern, where all the air was brought down one gate road and exited through the other gate road, loses large quantities of air through gobs giving a high methane concentration at the return end of the face. The 'Y' ventilation pattern where intake air is brought down both head and tail gate roads relieves the situation to some extent but, on most longwalls, some kind of methane control is still needed. With the onset of longwall mining in Europe several decades ago, the initial work on methane control on longwall has naturally been done there. The basic principle of methane control has always been, and still remains, some means of "bypassing methane from the gas emission space without letting it mix with the mine air". In most cases the bypassing mechanism is either a strategically located borehole or a roadway. A successful methane control program depends on the following basic premises: a. Determination of the geometry of the gas emission space and location of gas bearing horizons therein. b. Estimation of the rate of methane influx into the longwall gob. c. A scheme to bypass the gas in the most economic and efficient manner and thus prevent it from entering the mine atmosphere. In successful methane drainage programs a high proportion, usually between 50 and 70 percent, of the total gas emissions in a working district is removed before it can enter the mine airways. Advantages of methane drainage can be summarized as: 1. Generally reduced methane levels in the mine leading to increased safety and productivity. 2. Reduced air requirements and corresponding savings in ventilation horsepower. 3. Faster rate of advance for development headings and economy in the size of headings. 4. Possible use of mine gas as an additional source of fuel. The purpose of this paper is to briefly review the geometry of gas emission space and methane influx therein and discuss more successful European and U.S. longwall gob gas control techniques.

Jan 1, 1981

By William B. Senseman

For reasons well known to mining engineers, wet grinding is quite universal in plants having to do with the extraction of metallic values from crude ores. In the processing of the nonmetallic and industrial minerals, dry grinding is the more common method. The crude materials usually contain less moisture than is required for wet grinding and the products usually are marketed in dry form; most of them as powders. To grind wet, therefore, would entail the addition of water and an expense for drying the product, which is not justified. Furthermore, the material would be a dried cake that would still have to be pulverized or disintegrated before use. For producing fine products, air separators have largely replaced the earlier practice of sizing with screens and bolting reels. Mills in which the air-separating feature is an integral part of the design are now commonplace. Mill designs are many and air systems have developed along various lines, but for the purpose of this discussion, only the fundamental idea need be emphasized— the idea of using air for sizing and removing pulverized material from a grinding mill. About 20 years ago, when the use of mills equipped with air separation had become common practice, heated air or gas was introduced to such a system for the removal of moisture. The purpose of this discussion is to outline the developments and trends that have followed this experiment. It is an important development, for mills equipped with air separation are now universally used for pulverizing not only nonmetallic and industrial minerals, but a great variety of other materials. All such mills are essentially the same. Dried material is pulverized, removed by an air stream, trapped in a cyclone collector, and relatively clean air from the cyclone is returned through a fan to the mill. There is no theoretical need for a vent from the system. The practical need is to vent the air that leaks into the system, and, since the cyclone is not 100 per cent efficient as a dust collector, this vented air carries some dust with it. The initial attempt at drying was made on a system like that described, by the addition of a furnace. The minus pressure within the mill draws hot gas from the furnace. Infiltration air, along with the drying gases and evaporated moisture, is vented as before. The first application was made to a mill used for pulverizing coal. The coal contained very little moisture, so very little drying effect was needed for the success of this experiment. Actually, some calculated efficiencies of over 100 per cent were obtained before due allowance was made for the conversion of mill power into useful heat. When moisture is low, the heat obtained from the conversion of mill power is an appreciable part of that required. That drying can be effected in the short time interval available in a grinding mill of this type is better understood by visual-

Jan 1, 1947

By R. J. Borg, C. E. Birchenall

Vapor pressures of eight compositions of Mg-Cd have been determined by the Knudsen effusion technique. Measurements are made at several temperatures for each alloy and the results interpolated to a common temperature for the calculation of the activities. It is not possible to obtain values for the partial molar enthalpies because of the narrow temperature range spanned by the measurements. The results show less precision than those obtained for pure Cd which are also reborted. These alloys are extremely susceptible to corrosion which provides a possible explanation for the lack of precision. Nevertheless, the values of the activity are in good agreement with the results of electromotive force measurements previously reported for the Mg-Cd system. MAGNESIUM and cadmium are mutually soluble in all proportions in the solid state and form a single phase which has the hexagonal close-packed structure. X-ray investigations of this system1,2 have revealed a rapid variation in the relative dimensions of the unit cell occurring at approximately 50 at. pct. The rate of change of the c/a ratio with composition increases markedly for alloys containing more than 50 at. pct Cd. The purpose of this investigation was to determine the activity of Cd in the neighborhood of 50 at. pct and to discover whether or not the thermo-dynamic properties undergo a similar rapid change. The activities are calculated from vapor pressure data obtained by the Knudsen effusion method. Unfortunately the precision of the data from which the thermodynamic values are calculated is insufficient to establish unequivocally a departure from the normal trend. The results are reported primarily because they substantiate the only previously reported activity measurements3 and because they include values for pure Cd which in contrast to those of the alloys show excellent precision. The Cd-Mg system is known to contain several ordered phases. However, this investigation was made at temperatures considerably above the transition temperatures, and the alloys may be regarded as nearly random solid solutions. EXPERIMENTAL Apparatus—The effusion cells are machined from solid tantalum rod. The lids consist of threaded, flanged rings of tantalum onto which are welded shallow cups of 4 mil molybdenum foil. The orifice, which is located at its center, is made by grinding off a small dimple produced with a sharpened punch. Such an orifice has been mounted in plastic, sectioned, and the thickness of the orifice edge measured in a microscope. The maximum thickness is 0.00016 in., and the Clausing factor is consequently equated to unity. The area of the orifice is determined by tracing its projection on the screen of the metallograph at a known magnification and measuring the area of the tracing with a planimeter. Excellent temperature control is achieved with a 4 by 18-in. alundum core, gradient-wound, furnace

Jan 1, 1960