Search Documents

By H. A. Bourne, E. L. Haden, D. R. Reichmuth

A circumferential-toothed bit with novel tooth form gave improved penetration performance. In this design the exterior flank of all teeth were vertical when in rolling contact with the hole bottom. Rock chips were generated by the interior flank of the tooth displacing the rock inwardly and downslope toward the center of the hole. A unique two-cone laboratory bit assembly enabled evaluation of numerous cone and tooth configurations. Some of the variables investigated, in addition to weight on bit, rotary speed and rock type, were tooth interference, percent tooth, hole bottom angle, attack angle and relief angle. Most tests were conducted dry on a brittle synthetic sandsone or a ductile quarried limestone. Tooth configurations were found to be more significant in the ductile material. This was attributed to the deeper tooth penetration before rock failure. These studies showed that the attack angle (angle beween interior flank of the tooth and rock surface) was the controlling variable; changing the tooth configuration from the assymetric or semi-wedge to the more conventional symmetric or wedge form reduced penetration performance; and penetration performance of circumferential-type cutters was directly proportional to rotary speeds up to 200 rpm. INTRODUCTION Much of the published literature on rock-chisel interactions describe experiments wherein symmetrical wedges are vertically loaded or impacted against a smooth rock surface.1-6 are is usually taken to insure that the indentation is not made near the edge of the rock specimen less erroneous data be obtained. The literature describes relatively few studies in which the investigator deliberately attempted to take advantage of an edge or free surface. In contrast, anyone who chips ice or breaks up a concrete sidewalk almost always works near an edge. Chisel "indexing," which has been considered by some investigator1,2,6,7 makes limited application of an edge or free surface. Probably the best documented investigation into applying this idea to drilling was that of Drilling Research Inc. at Battelle Memorial Institute.' Their "annular wing" percussion bit consisted of paired asymmetric chisels oriented so as to produce and move chips to the center of the hole. They predicted that the lowest energy requirement for chip generation would be achieved with a stepped hole bottom having a median angle of 45" to the horizontal. Results from limited tests showed that approximately 50 percent of the rock fragments were large and semi-circular in shape, as would be expected by a chisel impact near an edge. The remaining 50 percent were fine chips produced by the chisels in re-establishing the steps or ledges. Initial penetration rates with this bit were high, but they rapidly decreased. This was the result of excessive tooth wear caused by the constant friction on the gauge surfaces. The basic idea — circumferentially placed asymmetric chisels — still appears to have merit. If the concept could be applied to a rolling cutter bit, two of the shortcomings of the fixed chisel design could be overcome: (1) reduction in tooth friction, and (2) greatly increased cutter surface. Adapting asymmetric chisels to cutters rolling on an inclined hole bottom is restricted by bit geometry. The basic elements of roller rock-bit construction prevents the practical attainment of a 45" hole bottom angle. Nonetheless, experimentally it was considered desirable to investigate the influence of hole bottom angle to at least 40". This paper describes the laboratory studies conducted in evaluating the circumferential-toothed roller cutter rock bit. EXPERIMENTAL APPARATUS AND PROCEDURE BIT ASSEMBLY The cost of constructing a sufficient number of conventional three-cone rock bits to investigate circumferential cutter performance was prohibitive. Instead, a novel two-cone laboratory assembly which used an external bearing system was designed and constructed. The external bearings made it possible to alter the journal bearing angles and thus allow a wide flexibility in cutter configuration. Fig. 1 shows the laboratory bit assembly, the various bearing mount plates and the appropriate roller cutters for drilling shallow holes having hole bottom angles of 0, 10, 20, 30 or 40". The bit was limited to a drilling depth of 1 1/2 in. at the gauge teeth and a hole diameter of 43/4 in. This more or less intermediate size bit was chosen because it gave a more realistic match between bit teeth and the rock than would a microbit. Also, the rock sample size required was convenient and easy to obtain. CIRCUMFERENTIAL CUTTERS The tooth configuration used in our initial studies is shown in the upper half of Fig. 2. All cutters used in this series had the same tooth form — 43" included tooth angle, 2" positive relief angle and a horizontal tooth flat width of 1/32 in. Each cone cuts alternate rows except for the gauge row. The row-to-row spacing in view was 1/4 in. Static loading tests conducted earlier with asymmetrical chisels had been used to establish this spacing. These tests showed energy requirements for chip production increasing rapidly as the distances to the edge increased beyond

By Walter Crafts, W. D. Forging, John J. Egan

Although many elements reduce the tendency to porosity in steel castings, manganese, silicon, aluminum, calcium, titanium and zirconium appear to be most generally suitable for the purpose. The manganese and silicon contents are usually maintained in a fairly constant range. Silicon-killed castings often are made to be sound with little or no addition of the stronger degasifiers. In many cases, however, it is more practical to utilize the stronger degasifying elements, aluminum, calcium, titanium and zirconium. Since they greatly modify the composition, shape, and distribution of the nonmetallic inclusions, and thereby the ductility, the strong deoxidizers must be used in such a way as to form the least harmful types of inclusions. As the reasons for failure always to obtain good results have not been obvious, an effort has been made to determine the mechanism of solidification of steels deoxidized to produce certain types of inclusions. Diagrams representsing the mechanism of their formation have been constructed from the appearance of the nonmetallic constituents and have not only illustrated the limiting features of specific deoxidizing treatments with respect to inclusion formation and ductility, but have also indicated a relation between inclusions and resistance to hot tearing. Three different types of deoxidation treatment have been used for obtaining sound castings with relatively high ductility. The first method is to make and cast the steel under such conditions that deoxidation with silicon and a small addition of a strong deoxidizer assures soundness. The effective addition that will promote soundness without causing the formation of intergranular inclusions varies with the furnace practice and composition, but may be limitled to about 0.025 per cent Al, Zr or Ti. Up to 8.10 per cent Ca and 0.15 per cent V are also used for this purpose. The inclusions in these steels are characteristically glassy silicates and round or irregular sulphides. As pointed out by Sims and Lillieqvist,1 the formation of fine intergranular inclusions, which are detrimental to ductility, limits the amount of strong deoxidizers that may be added.

Jan 1, 1940

By J. Charles Miller

Natural carbon dioxide has recently been exploited in the United States in consequence of oil and gas developments in the Western States and the growing demand by transcontinental and transoceanic shippers for solid carbon dioxidc. The discovery by drilling of commercial deposits resulted in consideration of its geographic and geologic distribution and occurrence. Its wide distribution in nature is evidenced by its occurrence in the atmosphere, hydrosphere and lithosphere. The question of origin of carbon dioxide involves consideration of theories similar to those concerning natural hydrocarbons, although available evidence favors an inorganic rather than an organic source. Areas favorable to development of commercia1 production appear to be those in proximity to igneous rocks or in the vicinity of decadent volcanic activity, where, it has long been known, the gas is evolved either free or dissolved in the waters of fumaroles, geysers or mud pots. Structure contour maps are presented showing the Wagon Mound anticline in New Mexico and the Farnham anticline, Utah. A well drilled on the latter supplies gas to a 20-ton plant manufacturing solid carbon dioxide at Wellington, Utah, on the Denver and Rio Grande R.R., whence it is shipped to surrounding territory and to the West Coast. Before funds are invested in a plant for the manufacture of liquid or solid carbon dioxide, whether supplied by wells or springs, an effort to ascertain the volume of gas available is advisable. The use of present methods of estimation of gas reserves with modifications to account for the quantity absorbed by any water present in the producing formation is recommended. The Farnham anticline is used as an example and computations are made of the probable volume of gas originally present in the structure. No attempt was made to compute reserves in the Niland area, California, for the reason that in such areas it is believed the volume is indeterminate. Introduction Carbon dioxide, in liquid and solid form, has found a wide variety of uses other than its primary application in carbonating beverages. It is now used in more than 40 different ways, ranging from cooling or freezing to use in gas or liquid form for mechanical purposes, chemical industry, explosive, fire extinction, and tire manufacturing. Undoubtedly the chief supply of carbon dioxide is obtained from industrial plants or artificial sources and until recently natural deposits of the gas have received little consideration. Few will question the utility and perhaps dependability of artificial sources, which possess the advantage over

Jan 1, 1941

By J. Charles Miller

Natural carbon dioxide has recently been exploited in the United States in consequence of oil and gas developments in the Western States and the growing demand by transcontinental and transoceanic shippers for solid carbon dioxidc. The discovery by drilling of commercial deposits resulted in consideration of its geographic and geologic distribution and occurrence. Its wide distribution in nature is evidenced by its occurrence in the atmosphere, hydrosphere and lithosphere. The question of origin of carbon dioxide involves consideration of theories similar to those concerning natural hydrocarbons, although available evidence favors an inorganic rather than an organic source. Areas favorable to development of commercia1 production appear to be those in proximity to igneous rocks or in the vicinity of decadent volcanic activity, where, it has long been known, the gas is evolved either free or dissolved in the waters of fumaroles, geysers or mud pots. Structure contour maps are presented showing the Wagon Mound anticline in New Mexico and the Farnham anticline, Utah. A well drilled on the latter supplies gas to a 20-ton plant manufacturing solid carbon dioxide at Wellington, Utah, on the Denver and Rio Grande R.R., whence it is shipped to surrounding territory and to the West Coast. Before funds are invested in a plant for the manufacture of liquid or solid carbon dioxide, whether supplied by wells or springs, an effort to ascertain the volume of gas available is advisable. The use of present methods of estimation of gas reserves with modifications to account for the quantity absorbed by any water present in the producing formation is recommended. The Farnham anticline is used as an example and computations are made of the probable volume of gas originally present in the structure. No attempt was made to compute reserves in the Niland area, California, for the reason that in such areas it is believed the volume is indeterminate. Introduction Carbon dioxide, in liquid and solid form, has found a wide variety of uses other than its primary application in carbonating beverages. It is now used in more than 40 different ways, ranging from cooling or freezing to use in gas or liquid form for mechanical purposes, chemical industry, explosive, fire extinction, and tire manufacturing. Undoubtedly the chief supply of carbon dioxide is obtained from industrial plants or artificial sources and until recently natural deposits of the gas have received little consideration. Few will question the utility and perhaps dependability of artificial sources, which possess the advantage over

Jan 1, 1941

By John J. Egan, W. D. Forging, Walter Crafts

Although many elements reduce the tendency to porosity in steel castings, manganese, silicon, aluminum, calcium, titanium and zirconium appear to be most generally suitable for the purpose. The manganese and silicon contents are usually maintained in a fairly constant range. Silicon-killed castings often are made to be sound with little or no addition of the stronger degasifiers. In many cases, however, it is more practical to utilize the stronger degasifying elements, aluminum, calcium, titanium and zirconium. Since they greatly modify the composition, shape, and distribution of the nonmetallic inclusions, and thereby the ductility, the strong deoxidizers must be used in such a way as to form the least harmful types of inclusions. As the reasons for failure always to obtain good results have not been obvious, an effort has been made to determine the mechanism of solidification of steels deoxidized to produce certain types of inclusions. Diagrams representsing the mechanism of their formation have been constructed from the appearance of the nonmetallic constituents and have not only illustrated the limiting features of specific deoxidizing treatments with respect to inclusion formation and ductility, but have also indicated a relation between inclusions and resistance to hot tearing. Three different types of deoxidation treatment have been used for obtaining sound castings with relatively high ductility. The first method is to make and cast the steel under such conditions that deoxidation with silicon and a small addition of a strong deoxidizer assures soundness. The effective addition that will promote soundness without causing the formation of intergranular inclusions varies with the furnace practice and composition, but may be limitled to about 0.025 per cent Al, Zr or Ti. Up to 8.10 per cent Ca and 0.15 per cent V are also used for this purpose. The inclusions in these steels are characteristically glassy silicates and round or irregular sulphides. As pointed out by Sims and Lillieqvist,1 the formation of fine intergranular inclusions, which are detrimental to ductility, limits the amount of strong deoxidizers that may be added.

Jan 1, 1940

By Clyde Orr

INTRODUCTION Cracks, crevices, holes, and fissures -- here collectively termed pores -- occur in all manner of substances in sizes from those evident to the unaided eye to those well below electron microscopic levels of detection. Naturally occurring materials having varying degrees of porosity are represented by wood, rock, soil, and mineral formations. Man-made materials that are porous include ceramics, sintered metals, catalysts, adsorbents, filters, and various compacted objects. The extent of their porosity greatly influences the hardness, rigidity, integrity, and general usefulness of such materials, and assessing both their pore volume and size is becoming increasingly necessary. Means by which this pore information can be obtained is the subject here. No attempt will be made to include all techniques and variations of them that have been suggested, but, hopefully, those of most general applicability will be described in sufficient detail to enable a potential user to judge their merit for a particular need. The results of pore measurements are made useful by relating them through other tests to performance criteria such as weatherability, water penetration, frost damage, oil recovery, strength, or thermal or electrical conductivity. These tests, of course, are outside the bounds for inclusion here. A pore is variously defined in dictionaries as "a minute opening", "a small interstice admitting passage of liquid", and "an interspace between particles". Clearly any object through which it is possible to find a continuous path from one side to the other either for a liquid or a gas must be regarded as porous. Passageways are not necessary for porosity to exist, however. There are so-called blind

Jan 1, 1980

By T. D. Mueller

Many investigators have used the response of the "dimensionless aquifer" to a unit pressure drop or a unit fluid-withdrawal volume to calculate the performance of an aquifer in supplying water influx to an oil reservoir. In the past, these response functions have been calculated with the aid of the Laplace transform. With the advent of ultra highspeed digital computers, it becomes practical to solve for the response functions with finite-difference techniques. The computer method also permits extension of the dimensionless-aquifer concept to include the nonhomogeneous aquifer wherein the permeability and other properties vary as a function of the space co-ordinates. This paper gives results of calculating the response functions for a series of nonhomogeneous aquifers. Response functions are presented for both linear and radial aquifers whose thickness, permeability-viscosity ratio and porosity-compressibility vary. These functions are new and should prove useful to the petroleum engineer in analyzing the behavior of nonbomogeneous aquifers. Results are presented in the form of charts that can be easily used by the field engineer. INTRODUCTION Aquifers which surround many oil and gas reservoirs have the ability to supply water influx to such reservoirs as oil and gas are withdrawn. This water influx, called natural water drive, provides one of the most effective driving mechanisms for the production of oil and gas. In producing a reservoir, therefore, it behooves one to make the maximum use of natural water drive. To achieve the maximum use, the reservoir engineer must be able to predict the performance of an aquifer under a variety of production schemes that may be proposed for the reservoir. Unfortunately, the physical properties which dictate aquifer behavior often are known only within limits. Seldom do wells penetrate the porous strata of the aquifer. Even when they do, quantitative information regarding porosity, permeability and water compressibility is seldom available. It is known, however, that the water efflux from most aquifer systems is governed by a single, relatively simple, linear, partial differential equation. Also, the general physical location of the aquifer boundaries often are known. A technique originall proposed by Hurst1 and van Everdingen and Hurst2 has been found useful in analyzing reservoirs in this situation. The idea was later expanded by van Everdingen, Timmerman and McMahan3 to include the mathematical technique of least-squares fitting. This latter method will be referred to as the VTM method. The basic assumptions of the VTM method include the following. 1. The location of the physical boundaries of the aquifer are known. 2. The flow conditions at these physical bound-daries are also known. 3. The aquifer is homogeneous; e.g., thickness, permeability, water compressibility and porosity are constant throughout. In the VTM method, a material balance is made on the fluids entering and leaving the reservoir. In the balance equations, the water-influx term is represented as the product of the water influx from an arbitrarily-selected, dimensionless aquifer system times an unknown conversion number. This balance can be formed as many times as there are data points in the history of the reservoir. Each time, the conversion number can be evaluated. If the reservoir engineer has picked the correct dimensionless aquifer to represent the real aquifer, the conversion number remains constant for all balances that have been made over the history period. If such a situation occurs, the reservoir engineer can then predict the performance of the reservoir for any type of production scheme by using the function associated with that particular dimensionless system and the derived conversion number. These functions will be referred to as the response function of the aquifer. If the aquifer is nonhomogeneous (e.g., if the porosity, permeability, thickness, porosity, or

By W. M. Raynor

LARGE quantities of "midnight oil" have been consumed by researchers in attempting to develop a process to produce cold ductile zirconium at low cost. The tantalizing facts that zirconium is a bright, silvery, tarnish-proof metal and is 2 1/2 times as abundant in the earth's crust as copper, and thirteen times as plentiful as lead have resulted in much speculation on uses, ranging from automobile radiator grills to kitchen sinks. but unfortunately no low-cost process of producing it has so far been found. In the case of zirconium, we cannot say that "virtue is its own reward" for the principal virtues of the metal, namely, corrosion resistance at ordinary temperatures and ability to absorb gases at high temperature, are the very characteristics that defeat all of the usual recovery methods such as sintering, plating, or direct chemical reduction. The only method giving a pure metal sufficiently low in oxides, nitrides, etc. to be truly cold-malleable is the one developed by Van Arkel and DeBoer in 1925. This process involves decomposition of zirconium tetraiodide in contact with a hot filament and pre

Jan 1, 1947

By Geo. W. Bain

PRODUCERS of building stone have had to seek new and attractive uses for their output to supplement the diminished orders for standard products. Lunar is the direct result of the need of new outlets for marble and is. probably the most ingenious and attractive type to reach the market in a quarter of a century. It is a highly translucent stone which retains the same glistening sparkle in transmitted light that marble exhibits by incident rays. This sparkle sets it apart entirely from translucencies made of glass or even onyx, alabaster, and the distinctive exceedingly fine textured calcite marbles produced in Alabama and quarried formerly in northern Vermont and Quebec.

Jan 1, 1936

By M. L. Millican

The objective of this study has been to develop a method of log interpretation in the Delaware sand whereby the effects of the shale contained within the sand can be recognized and accounted for in a quantitative solution for porosity and water saturation. Both theoretical and empirical considerations are discussed. A simplified interpretation chart is presented which provides a means of amending the conventional porosity resolution of the Sonic log to compensate for the presence of shale. The amount of shale within the sand and its degree of lamination may be inferred from a calibrated gamma ray log. The resulting porosity value may then be used in conjunction with a knowledge of the formation resistivity to determine water saturation. Of added interest, particularly in the Delaware sand, is an approximation of permeability which may be derived empirically from the simplified chart. The discussion is illustrated by field examples. INTRODUCTION The performance of the Sonic log in defining the porosity fraction in clean, consolidated formations is well known, particularly in sandstones that are well compacted and free of shale. An approach to Sonic log porosity determination in shaly sands has been recently developed.' This method involves correcting the Sonic log readings by means of an a factor, where a is the ratio of the pseudo-static SP to, the static SP, and is a function of the amount of shale present. This method is dependent upon a contrast between the salinities of the drilling fluid and the connate water in the formation, inasmuch as this contrast produces the SP effect. In wells drilled with salt mud, the contrast, and with it the means of obtaining the a correction, disappear. In the Delaware basin, the large majority of rotary wells drilled to the uppermost sands of the Bell Canyon group employ salt mud as the drilling fluid. These sands have been the objective of most of the drilling exploration in the basin to date. A comparison of porosity values in these sands, as determined by core analysis, to Sonic log readings has indicated that a correction for the shaliness of the sand is needed. In the absence of an SP curve to determine the correction factor, the porosity resolution of the Sonic log in these sands has been questionable.

By J. Weertman

It is shown that conditions suitable for the conversion of straight dislocations into helices are common in crystals hardened either through long-range dislocation interaction or by jog formation on dislocation lines. For dislocations other than screw dislocations or dislocations nearly screw in orientation, helices can be formed with the aid of core difhsion at temperatures low relative to the melting point of the material. It is assumed that, once formed, helices will degenerate into dislocation tangles. THE dislocation tangle is one major dislocation arrangement observed by the transmission electron microscope which had not been predicted previously from dislocation theory. Since first being observed, the tangle itself has become important in applied dislocation theory. The Cambridge school (P. Hirsch) bases part of its theory of work hardening upon this phenomenon.' In spite of the fact that the tangle obviously is a structure of prime importance to a cold-worked crystal, until recently relatively little attention has been paid to the question of exactly why or how tangles arise. It was generally assumed at first that cross slip and perhaps jog formation will lead to tangles. However Wilsdorf and schmitz2 concluded that cross slip cannot markedly contribute to the tangles. The Wilsdorfs and Maddin3'* have proposed that tangles arise by means of prismatic dislocation loops and superjogs which are produced by a precipitation of point defects. Dislocations with superjogs or which have joined with prismatic loops are themselves dislocation sources and they can produce new dislocations, a process they call "mushrooming", which then tangle with each other. There is no question that the Wilsdorfs et al. mechanism as well as the cross slip one can pro- duce tangles. However these may not be the only paths leading to tangle formation. In this paper we wish to consider another way tangles can form. Our work will be based on the theory of dislocation screw We wish to show that whenever a crystal is cold-worked there always is present a "driving force" leading to helix formation and thus to tangle formation. We do not expect to observe well-developed, regular helices in cold-worked metals. Rather we would expect that after a helix is formed random interactions with nearby dislocations will cause a well-developed helical dislocation to go over into an irregular form. A dislocation tangle is, of course, a grouping of dislocations with irregular forms. Therefore we feel that, in accounting for the formation of dislocation tangles, it is sufficient to show that many dislocations in a cold-worked crystal will take on helical form. The crucial step is helix formation. In order to have a straight dislocation assume a helical form, diffusion of vacancies, or interstitials, must occur. Our discussion of tangle formation therefore will be limited to crystals which have been deformed at temperatures ranging from about one fifth to half their absolute melting point. In this tem per a ture range appreciable core diffusion is possible. (There is no problem in explaining tangle formation at temperatures greater than half the melting point. At such temperatures dislocation climb through a bulk diffusion of point defects gives an extra degree of freedom to dislocation motion. This extra freedom of motion makes tangle formation easy.) At temperatures much below one fifth the absolute melting temperature diffusion processes are sufficiently slow that helix formation does not occur. Of course helix or tangle formation could occur in material deformed at very low tempera-tures which was subsequently warmed in order to make the thin specimen necessary for electron-microscope examination. Since within the temperature range of approximately one fifth to half the melting temperature the diffusion of point defects in the core of the dislocation is rapid, we can reasonably assume that within

Jan 1, 1963

By S. T. Wellman

The gradual change within the Iast few years from wrought-iron to steel for many purposes, notably for rails, plates, beams and other structural shapes, has brought the desirability and possibility of casting and rolling the steel in very large masses as compared with the

Jan 1, 1891

By E. J. Freeh, W. E. Horst

Mathematical models of a continuous comminution process are developed as an extension of the batch grinding model. Pilot-scale experimental work is described and the results are used to demonstrate the capability of the comminution models to simulate observed behavior over a relatively wide range of process variables.

Jan 1, 1973

By R. L. Tobie, H. W. Seaney

Over the years since 1956 when initial experiments were conducted on underground concreting in an attempt to cope with the ground weight and pressure encountered in the development of a large-scale underground block caving system, the use of monolithic concrete linings has grown to include most of the primary development in the mining area. Although the development cost of concrete linings is higher than either timber or steel-supported openings, the repair and maintenance costs are substantially lower, making concrete the most economical means of ground support. Other ad- vantages are also apparent, in that concrete provides superior fireproofing, better ventilation, and a safer, cleaner working place.

Jan 11, 1965

By William G. Fricke

MaCROSEGREGATION, as distinct from microseg-regation, is often inverse in nature. That is, the eu-tectic solute elements, which are expected to be con-

Jan 1, 1970

By E. O. Wagner, V. F. Parry

This paper summarizes investigations during 1949 on three pilot plants for drying low-rank fine coal by entrainment in hot gases. Detailed operating results on processing seven coals having moisture ranging from 24 to 62 pct, formulas and data for calculating performance of large units, and general conclusions on the problem of drying fine coal are presented.

Jan 9, 1950

By Roger B. Alke

INTRODUCTION Request to Mine Beneath Bridge The Jakes Run Bridge is a reinforced Portland concrete arch filled bridge located on WV Route 7 near Pentress, WV. The bridge has a span of 22.9 m (meters) and a height of 4 m above normal pool elevation to the underside of the center of the arch (See Fig 1). The bridge is a two lane structure with a width of 6.86 m. The structure is over 50 years old having been built in 1929 and is owned by the Department (WV Department of Highways). [ ]

Jan 1, 1984

By Kenneth W. Luke

A computer programing system has been devised to assist in open pit mine design planning. This system operates upon data generated for cross sections in the mine plan, and parallels present manual methods used in mine design, resulting in a minimal communications barrier between the mine planner and the computer. Input data for each cross section includes geologic interpretation and mine design parameters such as wall angles, bench heights, berm widths, and ramping system. The program will optimize the design of each cross section to give minimum stripping at any desired ore reserve level. This system is functional in the sense that it is easily adopted, changes in mine design parameters can be quickly evaluated, and each resultant design incorporates all recognized mining constraints.

Jan 1, 1973

By Felix G. Berra, David H. Orr

The first large scale application of radio remote control equipment to standard gage railroad trains has been achieved at the Morenci mine of Phelps Dodge Corp. at Morenci, Ariz. Twenty or more ore and waste haulage trains are remote control operated at any one time, each with a one-man crew. Reduction of train crews from two men to one man has materially lowered the total cost of train operation. Elimination of brakemen has also resulted in an improvement in train efficiency brought about by a shortening of train haulage cycle times.

Jan 4, 1965

The income of the Institute is derived mainly from dues, advertising in MINING AND METALLURGY and sale of publications. These sources are fortunately supplemented by the interest from invested funds now amounting to over $500,000, a considerable portion constituting endowments for especial purposes. Aside from the medal funds the principal endowments are the James Douglas Fund for support of the Library, the Rocky Mountain Fund and the Seeley W. Mudd Memorial Fund. The income from the two last named is available for the support of research and a variety of other purposes. It is allocated by the Board of Directors upon recommendation of standing committees in each case. An active effort is being made to increase the endowments of the Institute, it being felt that unusual opportunities exist for research and public and professional service through the organization.

Jan 1, 1938