Search Documents

By H. H. Kaveler, Z. Z. Hunter

Variation of the horizontal permeability (parallel to the bedding plane) in the vertical section of reservoir rocks has long been observed as a characteristic of a normally heterogeneous system which reservoir rock represent. The use of a recently developed water injection profile device offered opportunity to measure with a high degree of reliability the rate of inflow of water into Burbank sandstone in wells previously cored. Water injection profiles were not correlative with core permeability profiles in such wells. Apparently the vertical permeability substantially influences the flow between strata in a formation in a manner as to void the usual conclusions that have been drawn from consideration of the horizontal permeability measurements alone. The results obtained in comparing water injection profiles with horizontal permeability profiles suggest that many of the usual production operations based upon "selective" behavior or treatment of rock exposed in well bores need to he re-valuated and re-examined. INTRODUCTION Petroleum reservoir rock are heterogeneous systems. Heterogeneity exists in respect to lithologic character insofar as such rock are composed of distinguishable solid phases. Heterogeneity also exists in respect to certain properties, such as porosity and permeability, that vary due to variation of the physi-cal structure of the rock. Except in exceptional cases, both the horizontal permeability (measured parallel to the bedding planes) and the vertical permeability (measured perpendirularly to the bedding planes) exhibit significant variation in any common source of supply. The variation in horizontal permeability. as reflected by con. analyses. has drawn the greatest attention of petroleum technologists probably out of the general notion that the mass movement of fluids in a reservoir is predimonantly in the horizontal direction. Furthermore, in the usual case, the rock permeability measured in the horizontal direction is greater than that in the vertical. The variation of horizontal permeability of reservoir rock has been the basis for developing a number of operating practices and procedures intended to improve the petroleum production operation. Many such procedures are referred to as "selective" in the sense that the practice is intended to control the flow to a more. or less. permeable interval within the common source of Supply. It is often said that such practices are "tailored" to the permeability profile. The practices referred to involve, among others, the following: selective perforation of casing; selective shooting, acidizing and plugging: plugging back to intervals of low permeability; and, regulation of flow to prevent coning of water or gas, or irregular encroachment of water or gas. Certain expressed notions involving a concept of "by-passing," or "trappingl" that are held to be particularly harmful in causing the avoidable loss of recoverable petroleum have grown from observed variations in the horizontal permeability. Oftentimes estimates of the reserve of a common source of supply are tempered by conclusions relating variation in horizontal permeability to recover-ability of the oil-in-place. Certain conclusions attributed to the significance of the variation of the horizontal Permeabilitv often extend to the design and operation of pressure-maintenance projects involving both water flooding and gas-injection. Many advocate increasing the number of injection wells, advocate maintaining uniform and equidistant input-output well patterns, or advocate so-called "dispersed" gas-drive techniques rather than gas-cap injection because the permeability profile of cored wells is supposed to indicate that "by-passing" or "trapping" would otherwise exist. It is important, therefore, to have an opportunity to test whether the variation in the horizontal permeability found through core analyses of a typical reservoir rock is sufficient to establish the paths of fluid flow in a reservoir. It is particularly important to have an opportunity to determine whether flow at the sand face of a well conforms to the permeability profile as established by core analyses. In that manner, the merit of certain 50-called "selective" operating procedures and other notions may be evaluated. The purpose of this paper is to compare horizontal permeability profiles of wells in the Bartlesville (Bur-bank) sandstone with water injection profiles, for the purpose of showing that there is no correlation between the horizontal permeability of a core and the water intake characteristics of a typical sandstone. GENERAL CHARACTERISTICS OF BARTLESVILLE (BURBANK) SANDSTONE The Bartlesville sandstones of Northeastern Oklahoma are off-shore bar deposits.' Although other reservoirs had different processes associated with their deposition or with the formation of their porous, permeable structure, the l!artlesville sandstones on which these field Fields were made are, in every respect. typical petroleum reservoir rock. The permeability of the Bartlesville sandstones shows a typical variation in both the horizontal and vertical direction. Furthermore, the permeability profile logs of wells in any pool are not correlative, even as between wells as close as 660 ft and 330 ft apart.'. The same condition exists in such sand-tones as the Jones Sand at Shuler' and is the ordinary and usual characteristic of reservoir rock. THE FIELD DATA The data reported herein are those obtained from coring of nine wells on the center of ten-acre locations for the purpose of providing water-injection wells in the Bartlesville (Burbank)

Jan 1, 1952

By J. H. Rushton, L. H. Mahony

Principles of fluid motion and turbulence which have been found to be of use in mixing and agitation problems are discussed, as well as suggested applications in extractive-metallurgy processes. Various types of impellers are described, together with other conditions that affect flow pattern and turbulence. The choice of equipment for particular requirements is considered, and equations for power input are given. Modern heavy-duty mixing and agitation equipment can take an increasingly important part in such extractive-metallurgy processes as solids handling, crystallizing and leaching, chemical operations, and flotation. Application of mixing and fluid-mechanics principles to extraction methods can lead to greater process rates and a resultant saving in time and money. MIXERS are being applied with increasing frequency to problems in the metallurgical industries. The increase represents in part the modernization of mechanical equipment used through the application of unitized drives, modern electric motors and speed reducers, and recently developed materials of construction. Some applications have resulted from process changes and the use of techniques for operations similar to those that have been demonstrated and proven in the chemical industry. Still more applications are being developed through the use of fluid-dynamics principles not previously recognized as applicable to these operations. It is the purpose of this paper to describe those principles of fluid motion and turbulence which have been found to be of use in mixing and agitation problems, and to suggest applications for them in the extractive-metallurgy processes. Modern mixing equipment has been designed to provide the fluid motion consistent with that best suited to different operations.' When properly applied, these more efficient fluid-handling mixers result in lower process-production costs. Metallurgical operations usually involve large amounts of solids. The characteristics of the ore control the process and only enough liquid is added to provide sufficient fluidity for handling and processing. The reactive part of the ore, the mineral value to be extracted, is likely to be low in percentage, and the quantity of reagent required is similarly low, but excessive dilution makes additional reagent necessary and therefore is undesirable. Thus, the primary problems in minerals processing are to handle as high a concentration of solids as possible and to distribute reagents uniformly. These pulps, or slurries, are in a range of solids concentration where hindered settling rates apply, and care must be taken to agitate and mix sufficiently to maintain suspension and flow throughout the equipment. Such slurries have high densities which are the weighted average of the components and viscosities that are spoken of as "effective viscosities" but are difficult to evaluate. It is convenient to separate metallurgical operations involving mixers and agitators into three categories: solids handling, mechanical or physical operations, and chemical operations. In each of these categories fluid motion is required to maintain suspension, to distribute surface-active agents, to blend components and reactants, and to induce high rates of chemical reaction. After a discussion of some basic principles of mixing and agitation, examples of application to the three categories will follow. Fluid Motion The fundamental problems of mixing and agitation of liquids have to do with the mechanics of fluid streams and the means by which they are

Jan 1, 1955

By Thomas W. Wälde

BACKGROUND Foreign investment has been a major factor in bringing about the substantial mining industries of Chile, Peru, Bolivia, Venezuela, Brasil and Guyana. But economic nationalism and sentiment against foreiqn domination of vital national industries grew in the 1960s and most major mining projects were transferred into state owner ship. Among the state mining enterprises formed were CODELCO - Chile, MINERO-PERU/ CENTRCMIN - Peru, CCMIBOL - Bolivia (in 1952), Hierro-PERU, GUY-BAU/BIDCO - Guyana, etc. New investment during that time was discouraged because it was subject to the restrictive conditions of the investment regulations of the Andean-Pact, a grouping of Chile, Bolivia, Peru, Ecuador, Venezuela and Colombia. The philisophy was that mineral resources were to be developed exclusively by national enterprises. Essential foreign inputs had to be acquired "depackaged" as separate purchases of equipment and technical assistance services. As a result of the worldwide economic recession which hit the mining industries in 1980-1982, many projects that were viable in 1970 were not developed by the new state enterprises due to lack of capital, managerial and technical abilities and due to problems with marketing. As a consequence of the long-term decline of metal prices, governments experienced difficulty in getting investment organized through national or foreign enterprises and have had to face up to the trade-offs between national control and active mineral development. A change has since taken place in governmental policies. The 1981 Peruvian mining law, the 1982 mining law of Uruguay, the 1979/1980 mineral promotion laws of Argentina, all witness the gradual shifting of emphasis from restriction to promotion. The investment rules of the Andean Pact have been progressively softened through national regulation and today are more or less irrelevant. Nationalizations and forced renegotiations have not occurred in the last few years. Countries have gone to great lengths (without much success) to re-attract foreign investment on terms that accommodate the political sensitivities of the South American countries and the practical requirements of investors and financiers. For this analysis, three contracts have been selected which reflect this accommodation in three South American countries, where miner a1 production plays a major role in the national economy. These con tracts reflect both the attitudes and traditions of the individual countries, but also mark the shift in mineral investment policies that has taken place. EL INDIO AGREEMENT The 1977 investment agreement between Chile and St. Joe Minerals marked a dramatic relationship between Chile and foreign mining investor s. In Chile, mining of copper has played a major role in the country's history. Large scale copper mining was initiated and developed by Kennecott and Anaconda. The nationalization of these two companies under the Allende government in July 1971 started a wave of nationalizations of foreign-held mining and petroleum operations since then in many parts of the world. The military government supported the new Chilean state mining companies ((30DELCO and ENMI) , but it also attempted to accelerate mineral development by prom ting foreign private investment, thus reversing the nationalistic policies followed by the Allende and the preceding Frei government. The new policy by the military government is expressed in Decreto-Ley 600 (1974) which governs foreign investment in Chile. Decreto-Ley 600 is

Jan 1, 1985

By John W. Buch

NeaRly 25 years ago operating officials in the northern anthracite field were confronted with the problem of profitably mining virgin beds of thin coal (those 48 in. and under) or destroying them by mining underlying thick beds. To solve this problem costly hand-mining methods were replaced by cheaper mechanical methods, which eliminated the need for the lifting of bottom or the brushing of top in excessive quantities, which was essential if proper height for hand loading1 was to be provided. During this period long-face mining was an outstanding development. In its favor in comparison with any other method were the ease with which undercutting machines could be used, a differential in powder cost of about fifteen cents per ton in favor of this method over mining from a solid chamber or pillar face, and a greater production per day from a single working place, resulting in lower capital expenditures for a given total production, closer supervision and lower transportation cost. The long faces were drilled by jackhammer and undercut by machines. The coal from the cut was loaded into mine cars placed on the gangway road by means of a double-drum mechanical scraper engine and a mechanical V-type scoop. A tugger hoist was used to spot empty cars at the loading point from a supply placed at the operation by an electric mine locomotive. During loading the roof was supported by vertical wooden props paralleling the face. After the loading was completed the scraper engine and the ropes that had been used to propel the scoop in the loading of coal transferred the props to and along the face. A row of unfilled cogs was then built parallel to the new face and about 6 ft. from it. These cogs were usually made 6 by 3 ft., the longer dimension paralleling the face; they were placed on an average at 12-ft. centers. These wooden cogs were left in place and were buried later by falling roof. Attempts to remove them were never successful. When a new long face was started, the cog spacing would be increased to about 20-ft. centers. As successive cuts were made, weight would begin on the cogs, and they

Jan 1, 1940

By John R. Edwards

Introductory.—There are many interesting and important events connected with the petroleum problem. The remarkable men who conceived 'the thought of transporting petroleum by pipe line, conserving the byproducts of the commodity, and conducting extended investigation and research whereby the flash point of the oil was raised, its cost reduced and its supply assured, are deserving of the gratitude of this nation. It was primarily the success attained by Captain Lucas, after his comprehensive search for oil in Texas and Louisiana, that was the impelling cause which prompted the Navy Department to conduct the extensive series of liquid fuel-oil tests that were made from 1901 to 1903. The sensational discovery of oil at Spindle top made a deep impression upon Rear Admiral George W. Melville, then Engineer-in-Chief of the Navy, and the discovery of the vast oil field in Texas convinced him that, within a generation, if not within a decade, crude petroleum was going to play a very important part in warfare, and that the commodity might possibly develop into a necessary munition of war. The United States' Commanding Position as a Petroleum Producer.— In the study of the various problems relating to the world's production of crude petroleum, the position of the United States is one of commanding importance, whether viewed from the industrial or the military aspect. The present yield of this country is practically double that of the rest of the world, and, in view of the productive and prospective fields possessed by various countries, together with the comprehensive and exhaustive search that has been made throughout the world for petroleum, it is extremely probable that this lead will be maintained for the next decade. As regards the character of the crude-oil yield of different countries, America possesses the greater part of the supply that contains a paraffine base, and therefore a considerable portion at least of the American product produces the best illuminant. Of all the crude-oil distillates, kerosene is in many respects thc most important, and the Appalachian product for this purpose is favored, particularly in the Far East, above that of any other petroleum yield of the world.

Jan 1, 1915

By John W. Buch

NeaRly 25 years ago operating officials in the northern anthracite field were confronted with the problem of profitably mining virgin beds of thin coal (those 48 in. and under) or destroying them by mining underlying thick beds. To solve this problem costly hand-mining methods were replaced by cheaper mechanical methods, which eliminated the need for the lifting of bottom or the brushing of top in excessive quantities, which was essential if proper height for hand loading1 was to be provided. During this period long-face mining was an outstanding development. In its favor in comparison with any other method were the ease with which undercutting machines could be used, a differential in powder cost of about fifteen cents per ton in favor of this method over mining from a solid chamber or pillar face, and a greater production per day from a single working place, resulting in lower capital expenditures for a given total production, closer supervision and lower transportation cost. The long faces were drilled by jackhammer and undercut by machines. The coal from the cut was loaded into mine cars placed on the gangway road by means of a double-drum mechanical scraper engine and a mechanical V-type scoop. A tugger hoist was used to spot empty cars at the loading point from a supply placed at the operation by an electric mine locomotive. During loading the roof was supported by vertical wooden props paralleling the face. After the loading was completed the scraper engine and the ropes that had been used to propel the scoop in the loading of coal transferred the props to and along the face. A row of unfilled cogs was then built parallel to the new face and about 6 ft. from it. These cogs were usually made 6 by 3 ft., the longer dimension paralleling the face; they were placed on an average at 12-ft. centers. These wooden cogs were left in place and were buried later by falling roof. Attempts to remove them were never successful. When a new long face was started, the cog spacing would be increased to about 20-ft. centers. As successive cuts were made, weight would begin on the cogs, and they

Jan 1, 1940

By Carlos A. Aranda

The Smelting and Refining Department of Cerro de Pasco Corporation is located at La Oroya at an altitude of 3,720 meters (12,205 feet) in the Peruvian Andes. Producing lead, zinc and copper as well as twelve by-product metals and chemicals, the smelter is among the world's most complex. With the intake of high-bismuth ores in 1934, electrolytic lead refining by a modified Betts process was piloted and the plant went into commercial production in 1937 at a nominal capacity of 100 M.T. per day. After expansions in 1950 and 1963, nominal capacity has increased to 250 M.T. per day. Anodes spaced at 10.8 cm centre to centre and starting sheets are both set into the cells by overhead cranes. The asphalt-lined concrete cells are arranged in a Walker side-by-side configuration, and the electrolyte, circulating at 13 l/min./cell, is a solution of locally-produced hydrofluosilicic acid and lead fluosilicate. The corrosion cycle is limited to four days due to high impurity content of the bullion, which has successfully been treated at contents of up to 9% impurities. The cathodes are melted, drossed, and cast into blocks and pigs assaying 99.997 + % lead. The anodes with the blanket of slime adhering, are washed with electrolyte and condensate makeup water to remove the concentrated lead fluosilicate entrapped in the slimes. The slimes are then removed with high-pressure water sprays, centrifuged and sent to another plant for recovery of silver, gold, bismuth, selenium, tellurium, and antimony.

Jan 1, 1970

By G. Sherburne Rogers

Introduction. ONE of the features of oil-field work that puzzles operator, chemist and geologist alike, is variation in the gravity of the petroleum produced, on neighboring leases or even from adjoining wells. Few fields in the United States yield oil that is of uniform gravity throughout; in some, fields the different grades are produced from different sands, in a few from different formations, and in many from different areas in the same sand. In a few cases, perhaps, a common assumption-that the heavier oil is derived from the lighter through the escape of the more volatile constituents-is valid, but many cases can not be explained in this way. Although in the California fields the specific gravity of the oil generally decreases with depth, there are numerous exceptions to this rule; and, as in many other regions the light oil is found nearest the surface, it is evident that evaporation underground is generally an unimportant factor. It is generally recognized that the great differences between petroleum from widely separated fields are due largely to differences in age and degree of metamorphism and to variation in the composition of the original organic matter; but in the writer's opinion some of these broader differences, as well as most of the minor variations in the character of the oil from any one field, are clue to the local action of natural reagents such as sulphur or oxygen. This is particularly likely to be true if the oil has migrated from one formation to another, as in the California fields; and in some areas it appears that variation in sulphur content may even afford a rough index of the extent or distance of the migration. It is the purpose of this paper to call attention to the chemical action of sulphur and oxygen on petroleum, to show that the gravity of the oil from any one field is intimately related to its sulphur content, and to discuss the possi-

Jan 7, 1917

By Franklin Moeller

THE application of electric power for driving, mine hoists handling heavy loads at high speeds has recently been extended by the installation of what is probably the largest electrically driven hoist in this country at the Granite Mountain shaft of the North Butte Mining Co., Butte, Mont. While the weight of rock which is hoisted by this machine is not the largest now being handled by electric mine hoists, the speed of hoisting is so, and the combination of the high speed with the heavy load has resulted in a machine of considerable interest to all those actively engaged in mining. Aside from mere consideration of size, this installation deserves attention because of the careful attention given, not only to the question of economy of operation, but to the details of construction and installation of the entire equipment. The conditions to be met in this installation were as follows: Weight of rock to be raised per trip, 7 gross tons 15,680 1b. Weight of skip 8,0001b. Weight of cage 1,8001b. Maximum depth of hoisting 4,000 ft. Diameter of rope 153 in. Total weight suspended on one rope from drum 42,000 1b. Normal hoisting speed 2,700 ft. per minute. Maximum hoisting speed : 3,000 ft. per minute. Desired capacity-200 tons per hour from 4,000 ft: depth. The ore is mined in several levels and hoisting is carried on from the 800-ft. level down to the 2,700-ft., which is at present the maximum depth from which the ore is raised regularly. Development is proceeding and a depth of 2,900 ft. has already been reached. The rock is handled underground in cars holding ¾ ton, and about 10 cars are the usual load for a skip. All of the ore is clumped into underground bins, which are of different capacities varying up to 250 tons. From the bins the ore is fed into the skips without passing into measuring pockets. At the surface the

Jan 2, 1916

By L. B. Slichter

IT has been estimated that rock exposures in most mining districts aggregate less than 1 per cent. of the total surface area.1 Conclusions concerning the hidden 99 per cent. necessarily have been based on knowledge of only a small fraction of the surface, and from this limited information the geologist has been obliged to deduce the approximate and general nature of the underlying formations. In the search for ore it is necessary to supplement this general picture with greater detail. Fairly accurate knowledge of relatively small zones is required. This knowledge is carefully sought in many different ways-detailed interpretations of geological history, the tracing of float, the use of test pits, of trenching, of drilling, and of other methods. Practical ingenuity, scientific brilliance, great perseverance and patience, and the expenditure. of large sums of money have all been a part of this search. The problem of exploring beneath cover with economy, and of obtaining essential information which this cover hides, is obviously a difficult one. It is also a very important one, for geologists inform us that already the story of the 1 per cent. exposed outcrops has been largely read.2 There remains the nearly virgin field comprised in the hidden 99 per cent., and the importance of this zone is bound to increase continually. In recent years, the problems connected with the exploration of this "99 per cent. zone" have attracted a constantly enlarging group of investigators and at present greater efforts than ever before are being made to resolve then. This work, in its various special aspects, has enlisted, beside geologists, the cooperative efforts of chemists, physicists, and mathematicians. The progress made in this development should be kept before those directing explorations in order that due advantage may be taken of a changing situation.

Jan 1, 1928

Jan 1, 1927

By J. L. Kenty, J. P. Hirth

The concept of a critical super saturation, below which the nucleation rate is essentially zero and above which it is essentially infinite, is discussed with reference to vapor-solid nucleation. The necessary and sufficient conditions deduced for observations of this type of behavior are: 1) the nucleation rate must exhibit a sharp dependence on super saturation, 2) the growth rate must be sufficiently large that nuclei become observable in the time period of the experiment, and 3) the number of highly preferred nucleation sites must be small. Experiments reveal that the nucleation of silver on sodium chloride is visually detectable at all experimentally accessible super saturations and does not exhibit critical nucleation behavior. Failure to observe a critical super saturation is attributed to the insensitivity of nucleation rate to supersaturation as a consequence of the particular values of the contact angle and the surface free energy for this system. THE concept of a critical supersaturation, below which the nucleation rate is essentially zero and above which it is essentially infinite, arises naturally in homogeneous nucleation theory. Experimentally this type of behavior has been found by Volmer1 and others for water and other low surface tension liquids, as reviewed by several authors.2'3 The same type of behavior has been predicted and observed for heterogeneous nucleation of solids by Yang et al.4 and others,596 as also recently reviewed.2,7,8 In the work reported here on the heterogeneous nucleation of silver on NaC1, however, no critical super-saturation was found. Similar observations have been made recently for other systems.9-11 These results led to a reexamination of nucleation theory which revealed that there are conditions for which critical behavior is not predicted, either for homogeneous or heterogeneous nucleation. Although heterogeneous nucleation is of primary importance in this paper, some insight into critical behavior for such a case can be gained by considering homogeneous nucleation. Accordingly both types of nucleation theory are reviewed briefly. The requisite conditions for critical supersaturation behavior are then considered. The experimental results for the nucleation of silver on NaCl are presented and interpreted in terms of the theoretical presentation. REVIEW OF NUCLEATION THEORY There are essentially two approaches to nucleation theory, the so-called classical theory involving the concepts of bulk thermodynamics, and the statistical mechanical theory in which nuclei are regarded as macromolecules. The classical theory is based on the work of Volmer and Weber12,13 and Becker and. Doring14 and has been extended by Pound et al.15 The crucial assumption in the classical theory is that the small clusters or nuclei can be characterized by the same thermodynamic properties as those of the stable bulk phase. Thus, the nuclei are assumed to have a surface free energy, y, and a volume free energy of formation (relative to the vapor phase), ,, identical to that of the bulk. For deposition under low super-saturation conditions, the nuclei are large and this assumption is satisfactory. However, in many cases of interest, the nuclei contain only a few atoms and this assumption is highly questionable. The statistical mechanical models originated, for the specific case of a dimer as the critical nucleus, with the work of Frenkel16 and were extended later to larger sizes by Walton,17,18 Hirth19 and, more recently, Ht Zinsmeister. These models describe the nucleus in terms of a partition function, the estimation of which is tractable for clusters of 2 to 10 atoms, but extremely difficult for clusters larger than 10 atoms. Although the classical and statistical mechanical models are expected to apply for the limiting cases of large and small nuclei, both are uncertain for intermediate sizes. In this paper we shall treat only the classical model, recognizing that it is exact only for large nucleus sizes and regarding it as a phenom-enological description for small nucleus sizes. When analyses of experimental data using bulk properties show the nucleus size to be small, the resulting parameters should be regarded as largely empirical parameters describing the relative nucleation potency of the system. Considerable justification for the continued use of classical theory is provided by its general success in predicting nucleation behavior as a function of supersaturation and temperature. We emphasize that the qualitative features of the statistical mechanical models, particularly the critical super-saturation behavior that is central to the present work, are the same as those of the classical model. Of course, potential energy terms and surface partition functions replace the volume and surface energy terms of the latter model. The most recent versions of classical nucleation theory have been extensively reviewed.2,3,7 so that only the results are presented here. For homogeneous nucleation of a condensed phase from the vapor phase, the volume free energy change is ?Gv=vrT = =^ln£ [1] where v is the molecular volume of the condensing species. The supersaturation ratio,

Jan 1, 1970

By F. G. Miller, T. D. Mueller, L. B. Davidson

A mathematical model of reservoir behavior during one cycle of the intermittent steam injection process is presented in this paper. A cycle of the process is considered to be composed of three stages: injection, condensation and production. The model concentrates on behavior during the production stage. The influence of several parameters on production improvement is described, using the results obtained with a numerical equivalent of the model. Reservoir system parameters considered are thickness, reservoir thermal conductivity, oil viscosity, solution gas-oil ratio and the change in oil effective permeability with temperature. Operating parameters investigated are heat injection rate, steam temperature and cumulative injection time. In the face of considerable uncertainty, the model appears to give a fair prediction of the behavior observed during an actual test. This makes the model a useful means of selecting projects. It is shown that the model may also be utilized to select an optimum set of operating conditions for a particular project. Results of this study show the extent to which production improvement depends on each of the parameters investigated and give an indication of the range of system conditions within which the process would be effective. INTRODUCTION In recent years the intermittent steam injection or steam soak process of oil recovery has become a popular method of improving recovery in reservoirs bearing high-viscosity hydrocarbons. Production improvement due to the process results from heating the reservoir near the wellbore. The process is applied on an individual well basis and is executed in a series of cycles, each consisting of three stages: injection, condensation (the soaking period) and production. During the injection stage, high-pressure steam is injected into the reservoir surrounding the well-bore. This study assumes that injection is carried out over the entire vertical section of the reservoir rock that can be exposed to fluid injection. The condition of steam entering the reservoir is considered to fall within the following limits: (1) steam pressures less than 1,000 psig, (2) steam temperatures between 300 and 700F and (3) steam quality less than 90 percent. The last restriction is due to equipment limitations. Normally, injection re maintained for less than 3 weeks. After termination of injection, the condensation stage begins. The well is shut in for several days, supposedly to make certain that the injected steam condenses. This condensation would insure the retention of injected heat. The production stage is initiated when the well is opened again. Reservoir response during this stage determines the effectiveness of the process (response is defined as the oil production rates, the water production rates and the wellbore temperatures observed during the entire production stage). The immediate response of the reservoir is sometimes quite good. Sets of case histories by Longl and by Owens and Suter2 give some typical figures for response. Duration of the production stage is equal to the time needed for the oil production rate to decline to some predetermined value. This usually requires 4 to 6 months. Termination of the production stage coincides with the start of the next cycle. The process is continued, cycle by cycle, until it becomes unprofitable to continue. One simple model2 and two more sophisticated models3,4 of the process have been presented. These are based on fundamentally different assumptions than those used in this investigation. Although the three models might be modified to fit the assumptions used in this study, it is felt that greater rigor would result by developing a

By R. E. Reed-Hill, W. H. Hartt

The "(3034) " twin lamellae in magnesium have been reexamined using electron microscope replicas. The double twinning sequence (1011)- (1012) for these lamellae has been reconfirmed. Evidence is presented showing that the irrational habit of these twins is probably the direct result of a need to accommodate the second-order twinning shear. This accommodation vesults in both an external shear in the matrix and an internal shear in the lamella. A model is presented which accounts for the experimental obseruations. HCP metals are generally characterized by strong textures in which the basal planes of the grains tend to be aligned parallel to the rolling direction in sheet or plate and to the axis of wires and rods. Since these directions are normally those in which finished products may be subjected to uniaxial tensile stress, these textures effectively place the crystals of magnesium objects in orientations unfavorable to both basal slip and {1012) twinning, the easily activated deformation systems of this metal. However, when magnesium crystals are deformed near room temperature by a tensile stress nearly parallel to the basal plane, another mode of deformation can occur.',2 This is _a double twin which forms first by twinning on {loll), followed by retwinning on (1012). The resulting twin lamellae are of considerable interest. First, they can be responsible for "brittle fracture''; when a tensile stress axis lies in the basal plane, because the reoriented crystal structure of a lamella is well-aligned for slip while the parent crystal is not. Extensive internal deformation may thus occur while the matrix is still almost undeformed. This deformation can produce a ductile rupture running the length of the twin.3 Complete failure of the specimen may then oc-cure by the spreading of cracks from one twin lamella to another, or by the movement of a crack into a grain boundary and then along grain boundaries. Since the the volume fraction of these doubly twinned elements is normally very small, the fracture may be classed as brittle, although the fracture mechanism is, of itself, essentially ductile. It is quite probable that the ductility transition, normally observed4 in magnesium at or slightly Obove room temperature, is closely associated with these second-order twins. The detailed relationship of these twins to fracture in single crystals will be the topic of another paper. The present paper is concerned with a second important aspect: the irrational habit of these double twins that falls close to {3034), or approximately 7 deg away from the primary (10il) twin habit. There is good reason to believe that this habit results directly

Jan 1, 1968

By C. L. Pillar

INTRODUCTION The location, size, character of the ore de- posit and its adjacent formations will deter- mine the mining system best used for its ex- traction. The mining system chosen will have to be engineered to suit the ore deposit and the people that will extract it. What can be done in the Philippines cannot always be accomplished in the upper Northwest Territory of Canada. Mining operations developed under a free enterprise system are planned to achieve a satisfactory return on the capital required to place them into production. Hence, the choices made in planning and developing the mining system must be dictated by sound economics. The mining system planned must favor: 1. Maximum ore extraction of the deposit with minimal grade dilution. 2. The amount of capital expenditure used to develop and equip the mine must be in harmony with the financial policy of the group yet be sufficient to provide a reliable mining system. Excessive frills and extras that are not required for efficient, safe production should not be provided. 3. Mine production costs are determined by the amount of men, material, equipment and energy used in the production process. These must be kept to minimal limits in order to insure dependable, low cost production. Extras that later are needed in the production operation can be added as required by the operator. Basically block caving is a mining system that is normally used to extract deep seated, massive, low grade deposits of copper, molybdenum and iron where stripping ratios for open cast mining are economically prohibited. The caving system is limited in its selectivity. It is a mass production type of underground ore extraction that under favorable conditions is one of the most efficient, low cost mining systems in the world today. Usually block cave mining systems are large. They are capable of producing ore at a rate of 10,000 to 100,000 tons/day from large deposits at costs that are comparable with many open cast mining systems burdened by high waste to ore ratios. Block cave mining systems differ basically in the plan of the area layout, the method of undercutting and the method of draw. The balance of the mining system is the mechanical transportation of the drawn ore to the surface, the mine supply, drainage and ventilation systems. This paper deals mainly with the methods of draw. The method of draw to be used in a block caving system dictates the development plan of the mining area, is highly influential in the method of undercutting to be employed and the supply and ventilation system to be used. There are three basic methods of draw commonly used in today's operations. They are: Gravity draw Slusher draw LHD draw The type of draw planned will have a major affect on: Capital expenditure and time required to bring a deposit into production. Productivity, efficiency and cost of the production operation. Percent recovery of the ore deposit in both tonnage and grade. Degree of production reliability Fundamentally the type-of draw used must be compatible with the physical characteristics of the deposit to be extracted and the financial position of the mining operation. The type of draw chosen must work to advantage with the size, configuration, depth, strength and fracture pattern of the deposit and its adjacent formations. It must favor the financial protection of the planned mining operation. A Gravity Method of Draw requires a finely fragmented, easy flowing product from the caving action of the deposit. To obtain the desired economic advantage the ore deposit must also have sufficient area and height of column to permit minimal development cost on a per ton basis. The gravity system re- quires the maximum amount of development openings and uses the minimum amount of mechanized equipment of all the caving systems. It is unskilled, labor-intensive and is highly sensitive to size of ore fragmen-

Jan 1, 1981

By Lawrence H. Van Vlack

The energy of the y-iron grain boundary was determined to be 850 ergs per cm2 at 1105°C. The a/a and the a/y boundaries possess somewhat less energy. The microstructures of several iron alloys are discussed in terms of the interfacial energy relationships. THE dependence of the shape of liquid interfaces upon their energies has been studied for some time.1"3 Recently, Smith' concluded that many of the microstructures observed in metals may be attributed to the energies of the interfaces between the grains and phases. While the energies of liquid surfaces have been measured by numerous different methods: only two attempts have been made to determine experimentally the energy of surfaces involving crystalline solids. Udin, Shaler, and Wulff8 used a procedure introduced by Berggren7 to measure the surface tension of solid copper. It consisted of determining the load required on a thin copper wire so that the surface tension was counteracted, and no net strain resulted. Bailey and Watkins8 sed a different technique and were able to determine both the surface tension of copper and the tension of the copper grain boundary. They measured the contact angle which liquid lead makes against a copper surface. They then calculated the above energies from the surface energy of liquid lead by using the Pb vs. Cu/CuY dihedral angle and the surface groove angle formed during thermal etching. They obtained a value of 1800 dynes per cm for the surface tension of clean copper and approximately 640 dynes per cm for the tension of copper grain boundaries. The former value was somewhat higher than Udin's value of 1500 dynes per cm. This paper includes a determination of the energy of the y-iron grain boundary. In addition, the micro-structural relationships of several other metallic and nonmetallic phases with iron were examined and an attempt was made to interpret the observed structures in terms of interfacial energy relationships. Theoretical Considerations In a three-phase material containing a solid and two liquids, there may be two solid/liquid interfaces, one liquid/liquid interface and one inter- granular interface. Liquid/liquid interfacial energies can be measured directly. Therefore, by determining the energy of such an interface and by measuring the required interfacial angles: the energies of the interfaces involving solids may be obtained.10 They may be shown schematically as in Fig. 1. The above procedure requires the following assumptions: 1—The interfacial energies are, in general, unaffected by boundary orientation, and 2— the shapes of the interfaces are unaltered between annealing and sectioning for microscopic examination. The first assumption is good to a first approximation as shown by Dunn and Lionetti11 except for a few critically orientated boundaries. Two conditions may alter the shape of a boundary upon cooling: 1—Precipitation of dissolved material upon one side of the interface, and 2—a change in volume during the transition from one phase modification to another. The former must be detected by microscopic observation. The latter may become appreciable in systems containing an interface between two liquids which solidify after annealing. However, possible movement of the two-liquid interface may be checked in the system diagrammed in Fig. 1 by measuring 8, for example, and comparing it with its value as calculated from the other interfacial angles by: tan8, C11 05 COS- o- + cos 8, cos- The choice of a suitable pair of liquids is limited by several factors. The relative values of the several

Jan 1, 1952

By K. S. Lane

As the initial chapter in this section entitled "Role of Fluid Pressure in Rock," this attempts to fulfill an assignment for (1) summarizing the state-of-the-art and (2) illustrating engineering problems resulting from rock pore pressure. Hence, the chapter is presented in two parts: 1) Basic Concepts, and 2) Examples of Engineering Problems, including failures. Neither of these objectives has necessarily been completely met: partly from limitation of space and partly as the case histories have been restricted to the author's own field in civil engineering, and there deemphasizing those applications which will be covered in more detail by subsequent papers in this section. As with any state-of-the-art attempt, contributions of some have undoubtedly been overlooked (or omitted for brevity). Notwithstanding the foregoing limitations, it is hoped that this summary of the situation will at least: 1) Outline current concepts on effects of fluid pressure in rock-both as a pore pressure in interconnected void spaces of the intact rock and as a cleft pressure or hydraulic force acting in the joints or other discontinuities of the rock mass. 2) Indicate the often fragmentary nature of evidence presently available to support these concepts and thus encourage further research. 3) Illustrate the major significance of fluid pressure in several types of engineering problems and thus stimulate its consideration as designers encounter related situations.

Jan 1, 1970

By R. W. Schenker

INTRODUCTION Environmental and occupational safety and health requirements often have a major impact on the design of comminution circuits, leading to increased capital and operating costs and reduced income. A project's capital cost can be increased by environmental permitting delays and the addition of dust collection equipment. Income can be reduced by lost production during unscheduled plant shutdowns for dust collection equipment maintenance. Dust collection equipment must be carefully selected and sized to minimize impact on the project. The equipment performance must comply with environmental regulations and allow working areas to comply with occupational safety and health regulations. Unnecessary overdesign could jeopardize the project's desirability from an economic standpoint. The equipment must be sufficiently reliable to avoid interference with production schedules. This chapter provides practical information on the selection and sizing of comminution circuit dust collection equipment that is consistent with the requirements stated above. It presents information on the reasons and general principles of dust collection; various types of dust collection equipment; and design criteria for ventilation hoods, duct systems, fabric filter dust collectors, and fans. An example discussing the selection and sizing of dust collection equipment for a simple comminution circuit is also presented. REASONS FOR DUST COLLECTION Dust collection equipment should be installed in comminution circuits for a variety of reasons, some of which are discussed below. These include compliance with government regulations, minimization of housekeeping requirements, product recovery, and improvement in public and employee relations. Compliance with Government Regulations Dust emissions from comminution circuits must comply with both air pollution control and occupational safety and health regulations. The regulations that may influence the selection of comminution circuits are discussed in more detail in Chapter 2. Air pollution control regulations limit the emission of dust, as well as visible emissions to the atmosphere and the concentration of dust in the ambient air. These regulations minimize the degradation of air quality and impact to other environmental considerations such as the health of the general public,

Jan 1, 1982

THAT the march of civilization has synchronized with progress in the art of utilizing minerals is a proposition that needs no proof. It is a truism. Historians conveniently divide the time that the earth has been inhabited into the Stone Age, the Bronze (more accurately the Copper) Age, and the Iron Age. As archeologists are not entirely in accord as to dates, and as a few centuries make no difference whatever to this particular story, it may be approximated that the Age of Copper began about 8000 years B.C. and that it gave place to the Age of Iron about 1000 years B.C. The logic of this succession-stone, copper, iron-lies in the fact that copper first displaced stone, then iron displaced copper as the standard material out of which the utensils, implements, and weapons, the utilitarian articles of antiquity, were made. After the advent of iron, the mining and smelting of copper continued. Copper and bronze found use particularly in objects of artistic and ornamental nature; but the superior qualities of iron for many purposes were recognized. Useful manufactures of those days consisted principally of knives, hammers, chisels, spear-heads, arrow-heads, and battle-axes. First these were made of stone, then of copper and bronze, then of iron-particularly as there was plenty of iron ore, and the metallurgy was comparatively easy of accomplishment. Of course, the periods of transition dragged slowly. Definite as were the three Ages dominated by the mineral substance from which they get their names, ten or fifteen centuries probably elapsed from the time the first iron was smelted in a small charcoal furnace until it became the accepted material from which to shape a battle-axe. Contrast this with the pace of modern progress. In a brief span, half a dozen more or less deserving candidates for the distinction of having their name

Jan 1, 1933

By A. P. Boller

In the victories of peace as well as of war, the science of engineering has played a prominent, if, indeed, not the leading part. While it might be interesting, and food for profitable thought, to trace the development of engineering from early times in its bearings upon the social betterment of mankind, it will be sufficient on the present occasion to suggest a few thoughts that it is hoped will aid the unprofessional listener to an appreciative consideration of the subject-matter laid down for to-day's discussion, and possibly lead the professional brother to a higher conception of the profession to which he belongs. Since the advent of the railway era, it is difficult to grasp the sequence of historic events that have led to the wondrous derelopment of mechanical science, making possible the civilization that is our daily boast, and opening up a vista of future intellectual and moral advancement among the nations of the earth, 'before which the imagination becomes hopelessly lost. Even now, looking back over a period of only half a century, we often fail to realize the vast change in the relations of individuals and nations to each other., brought about by the results of those mechanical discoveries which, having made the whole world kin, exercise a resistless levelling influence that bears fruit politically in the spread of republican ideas, and morally in the elevation of the individual through the facilities given to the dissemination of Christian ideas and general intelligence. In this view, it seems almost like a work of supererogation for a body of representative men of one department of that science to which the whole world owe. so much, to meet here at the centre of our national life to plead not only for a practical recognition of the national importance of the work to which their lives are devoted, but also for national aid, on a scale beyond that of private effort, to the end that mechanical science may be carried to a higher plane than ever yet attained, each step on the way being of material benefit to every man, woman, and child in the community. Possibly this is strong language, but none too strong when we consider that the work for which we plead is one affecting not only vast scientific and commercial interests, but also human life, to a degree little ap

Jan 1, 1882