Search Documents

By D. T. MacRoberts

Tins paper embodies the results of theoretical studies concerning gas reservoirs, especially the effect of drilling programs of various intensities upon pressure depletion and ultimate recoveries. The primary objective has been to determine the net quantity of recoverable gas that could be obtained as a result of each additional well, in comparison with the gas that might be secured from a single well ideally placed with respect to both acreage and geological structure. No method is yet known whereby the relative merits of intensive and sparse drilling can be compared experimentally; a reservoir must either be drilled closely or developed with wide spacing, but both programs cannot be conducted simultane-ously. Hence, the analytical method seems to be the only approach to the problem. While the present state of our theoretical knowledge does not offer a precise solution to the problem of gas flow in sand bodies, it takes such appropriate cognizance of the limitations of the methods used as to restrict any answer obtained to the realm of engineering accuracy. In solving the problem for the average gas field, it was found that practically the same answers resulted as to pressure distribution, regardless of the size of the drainage radius, even though the latter was assumed to vary from a few feet as a minimum to that of the entire reservoir as a maximum. Such limits represent extreme possibilities; therefore, the practical conditions that are associated with normal development programs, in which wells are placed in the center of tracts varying in size from 40 to 640 acres, will of necessity result in less extreme variations than those indicated in the tables accompanying this paper. Stated more concisely, the amount of gas unrecovered at abandonment (of the particular field used for illustrative purposes) will lie somewhere between 4.6 and 6 per cent of the total original content, no matter how intensively the field is drilled.

Jan 1, 1938

By Walter White

THE measurement of the reading of a thermoelement is the measurement of an electromotive force extraordinarily small compared to those generally used in commercial work. Of the various possible methods of measuring such a quantity, the most advantageous is always a delicate galvanometer. Since a galvanometer measures current, it is necessary to adopt some scheme by which its current reading shall indicate electromotive force. There are two general methods of doing this. One is to use the delicate galvanometer as a "direct reader," that is, to let the electromotive force of the thermoelement furnish the power and produce the current measured. If the resistance is constant the reading will, after a suitable calibration, give the electromotive force of the thermoelement which, by means of a table or of a suitable scale in the galvanometer itself, will FIG. 1.-SIMPLIFIED POTENTIOMETER. POTENTIAL DROP ACROSS THE PART PIN or CIRCUIT OF BULL CELL BALANCES THAT OF THERMOELEMENT TC WHEN GALVANOMETER G READS ZERO. give the temperature. The other method, that of the potentiometer, is to balance the electromotive force of the thermoelement by means of another electromotive force, using the galvanometer to tell when the balance is made. The usual way of getting this other electromotive force is to have a battery, the "bull" cell, send a current through a series of resistances, which 'may in a special case be the resistance of a single wire. The fall of potential along this circuit will then, by Ohm's Law, be proportional to the resistance; the potential difference between any two points, proportional to the resistance between the two points. This is represented in Fig. 1, where M and N are the two points in the circuit AZ of the battery. If M or N, or both, is movable so that the resistance

Jan 9, 1919

NEW MEMBERS The following list comprises the names of those persons who became members during the period of Nov. 10, 1917, to Dec. 10, 1917. ADAMS, LLOYD D Supt., Hoskins Mine, Mineral Point Zinc Co., Galena, Ill. ARMSTRONG, WILLIAM D., Min. Engr.. Empire Coal Co., 715 American Trust Bldg., Birmingham, Ala. BALL, TOM LEE, Efficiency Engr., Iron Mines Dept., Tennessee Coal, Iron &.R. R. Co., Bessemer, Ala. BENZIE, WILLIAM ROSE, Sec. & Treas., The Republic Coal Co., 901-2 Foster Bldg.,Denver, Colo. BERGSTROM, GUNNAR, Min. Engr.... Resident Mgr., Russian Dept., Swedish Diamond Rock Drilling Co., Slatawostowskaja Ulitza 6, Ekaterinburg, Russia. CADOT, J., Engr.,. Hardinge Conical Mill Co., Newhouse Bldg., Salt Lake City, Utah. COFFEY, GEORGE W 64 Santa Clara Ave., Oakland, Cal. CUTLER, WILLARD WALKER, JR Geol., Carter Oil Co., Tulsa, Okla.' . DANIEL, JOSEPH A., Min. Engr. & Geol., Hudson's Bay Co., Care The Institution of Mining & Metallurgy, 1 Finsbury Circus, London, E. C., England. EARDLEY, WALTER HAZEN, Cons. Engr., Chanute Spelter Co., 316 Frisco Bldg Joplin, Mo.

Jan 1, 1918

By Eifu Moriyama

In 1953, Akita Plant, having a capacity of 560 tons per month, was built at Akita city by Mitsubishi Metal Mining Co., Ltd. for the purpose of treatment of the Ikuno and Akenobe Mines's zinc concentrates. Akita city, in whose neighborhood the black ore has been discovered, is located about 500 Km north of Tokyo and faced with the Japan Sea. This plant has been continuously expanded to have the capacity of 7,500 tons per month by the end of 1969. Efforts have been made to mechanize installations and to achieve continuous process. One of the characteristics of Akita Plant is the recent establishment of the residue treatment process. Many processes had been investigated, and finally commercial sulphate roasting of the residue has been carried out since 1965. At Akita Plant, special high grade electrolytic zinc, zinc alloy for die-casting (MAK brand), cadmium, cement copper and sulphur dioxide gas are produced. Sulphur dioxide gas is sent to the next door fertilizer plant to make acid. Table 1 shows production and the average assay of the electrolytic zinc and cadmium in 1969. This plant is divided into four main sections, two subsections, and residue treatment sections: Main sections are: (M-1) roasting section, (M-2) leaching and purification section, (M-3) electrolysis section, (M-4) melting and casting section,

Jan 1, 1970

The regular activities of the Institute are financed mainly by income derived from members' dues, from advertising in MINING AND METALLURGY, and from the sale of publications to the public In addition, collateral activities and special projects are financed each year by means of income from endowed funds controlled and administered by the Institute In the aggregate, the amount of these endowments totals more than $830,000 An active effort is being made to increase the endowment funds of the Institute through a standing committee, of which Harvey S Mudd is Chairman, and

Jan 1, 1952

By AIME AIME

PRODUCTION of nickel in Cuba, a new source of this metal, has been started by the Nicaro Nickel Co., subsidiary of the Freeport Sulphur Co. Construction of the Nicaro plant in Oriente Province, Cuba, and of a refinery at Wilmington, Del., has been "substantially completed," according to Langbourne M. Williams, Jr., president. The initial rate of output is less than capacity operation, which will be reached when "the customary problems incident to the commencement of full- scale production are eliminated." The plant in Cuba for the treatment of the extensive nickeliferous ores of that region, and the refinery, were built by Nicaro for the account of the Defense Plant Corp. construction has been under way for eighteen months. The plants, when operating at capacity, are expected to increase America's sup-

Jan 1, 1944

By J. A. Hafford, J. K. Kerver, J. G. Richardson, P. M. Blair, J. S. Osoba

This paper presents the results of laboratory measurements of relative permeabilities to oil and gas on small core samples of reservoir rock by five methods, and describes the influences of such factors as boundary effect, hysteresis, and rate upon these measurements. The five methods used were the "Penn State," the "single core dynamic," the "gas drive," the "stationary liquid," and the "Hassler" techniques. In those methods in which the results are subject to error hecause of the boundary effect, the error may be minimized hy the use of high rates of flow. In order to avoid complexities introduced by hysteresis, it is necessary to approach each saturation unidirectionally. Observed deviations of relative permeabilities with rate can be explained as a manifestation of the boundary effect, and disappear as the boundary effect vanishes. The results indicate that all five methods yield essentially the same relative permeabilities to gas. Of the four methods applicable to the determination of relative permeability to oil, three, the Penn State, single core dynamic, and gas drive, gave relative permeabilities to oil which were in close agreement. The Hassler method gave relative permeabilities to oil which were consistently lower than the results obtained by the other methods. INTRODUCTION The relationship between the effective permeability of a reservoir rock to each of the fluids flowing through it and the corresponding fluid saturation is an important characteristic of the reservoir rock. Knowledge of this characteristic is and gas reservoirs and of the ultimate recovery to be expected extremely important in the prediction of the behavior of oil under various operating conditions. These effective permeabilities are usually expressed as the "relative permeability" to a fluid phase, defined as the ratio of the effective permeability to the permeability of the rock to a single phase at 100 per cent saturation. Relative permeability-saturation relations are not the same for all kinds of reservoir rock, but may vary from formation to formation, and within the different portions of a heterogeneous formation. In studying the performance of a specific reservoir, it is necessary, then, that the relative permeability characteristics of the individual portions of the reservoir be measured. These measurements may be made in the laboratory on small core samples from the reservoir. Various techniques have been proposed for the measurement in the laboratory of relative permeability-saturation relations. In varying degree, difficulties attend the use of all of the methods which have been proposed. It is the purpose of this paper to discuss the factors which influence the measurement of relative permeability, the difficulties encountered in several methods, and to present comparative results obtained by the use of various techniques. FACTORS WHICH INFLUENCE THE MEASUREMENT OF RELATIVE PERMEABILITY It is necessary that the relative permeability data measured in the laboratory yield the same relative permeability-saturation relationships that would govern the flow of fluids through the sample if it were to occupy its original position in the reservoir. Since the core sample upon which the laboratory measurements are made is not surrounded by similar core material as it was in the reservoir, an error in measuring the relative permeabilities may arise from the "boundary effect" which results from a discontinuity in capillary properties of the system at the effluent end of the core. Again, the rates of

Jan 1, 1951

By Warren J. Jackson, John L. P. Campbell

Automatic recording of the radioactivity of the earth's formations provides a log of relative intensities that, if properly interpreted, can be applied to oil-field engineering. Production, engineering, and geological departments regard the radioactivity log as a forward step in the securing of more conclusive information for successful well completions. Explanations of the technique, together with some of the problems to which radioactivity logging have been applied, are presented in this paper. Introduction Those responsible for the completion of new oil and gas wells, or with planning workover operations on old wells, have followed closely the development of radioactivity well logging because they are interested in reducing the number of unknowns that usually are present in such work. Many operators have made use of the log, or are acquainted with at least one of the applications, but it is unlikely that any one operator is familiar with all of the many applications that are possible. The purpose of this paper is to present a representative example of each of the many applications, wherever the information has been released by an operator, and to illustrate by hypothetical examples other applications, releases for which have not been given. In this way, it is hoped that a better understanding of the scope of this new engineering tool may be obtained. Although the literature contains many references that describe in detail the theory, development, and application of radioactivity well logging, a brief discussion of the technique may be helpful to those who are investigating the subject for the first time. All rocks contain radioactive material in varying concentrations. In general, shales contain relatively more radioactive material than sandstones or limestones. These radioactive materials disintegrate with time into other materials of lower atomic weight, and in that process of disintegration the rocks are emitting many rays, the most penetrating of which is the gamma ray. The intensity of emission of the gamma ray is proportional to the quantities of radioactive materials present. A higher rate of emission would be observed, therefore, opposite a shale than opposite a sandstone or limestone. Since measurable intensities of gamma rays are capable of penetrating as many as five concentric strings of casing, and as the gamma-ray intensity is relative to the formations, the measurements of variations in gamma-ray intensities offer a means of identifying cased-off formations in their proper stratigraphic sequence. The Gamma-ray Curve The measurement of gamma-ray intensities is accomplished by means of an ioniza-tion chamber that consists of a heavy cylinder, about 3 ft. long, that contains two insulated electrodes and is filled with an inert gas under high pressure. Under normal conditions no current will flow through the gas when an electrical potential is set up between the electrodes, but when

Jan 1, 1946

By John L. P. Campbell, Warren J. Jackson

Automatic recording of the radioactivity of the earth's formations provides a log of relative intensities that, if properly interpreted, can be applied to oil-field engineering. Production, engineering, and geological departments regard the radioactivity log as a forward step in the securing of more conclusive information for successful well completions. Explanations of the technique, together with some of the problems to which radioactivity logging have been applied, are presented in this paper. Introduction Those responsible for the completion of new oil and gas wells, or with planning workover operations on old wells, have followed closely the development of radioactivity well logging because they are interested in reducing the number of unknowns that usually are present in such work. Many operators have made use of the log, or are acquainted with at least one of the applications, but it is unlikely that any one operator is familiar with all of the many applications that are possible. The purpose of this paper is to present a representative example of each of the many applications, wherever the information has been released by an operator, and to illustrate by hypothetical examples other applications, releases for which have not been given. In this way, it is hoped that a better understanding of the scope of this new engineering tool may be obtained. Although the literature contains many references that describe in detail the theory, development, and application of radioactivity well logging, a brief discussion of the technique may be helpful to those who are investigating the subject for the first time. All rocks contain radioactive material in varying concentrations. In general, shales contain relatively more radioactive material than sandstones or limestones. These radioactive materials disintegrate with time into other materials of lower atomic weight, and in that process of disintegration the rocks are emitting many rays, the most penetrating of which is the gamma ray. The intensity of emission of the gamma ray is proportional to the quantities of radioactive materials present. A higher rate of emission would be observed, therefore, opposite a shale than opposite a sandstone or limestone. Since measurable intensities of gamma rays are capable of penetrating as many as five concentric strings of casing, and as the gamma-ray intensity is relative to the formations, the measurements of variations in gamma-ray intensities offer a means of identifying cased-off formations in their proper stratigraphic sequence. The Gamma-ray Curve The measurement of gamma-ray intensities is accomplished by means of an ioniza-tion chamber that consists of a heavy cylinder, about 3 ft. long, that contains two insulated electrodes and is filled with an inert gas under high pressure. Under normal conditions no current will flow through the gas when an electrical potential is set up between the electrodes, but when

Jan 1, 1946

By J. K. Kerver, J. S. Osoba, J. G. Richardson, P. M. Blair, J. A. Hafford

This paper presents the results of laboratory measurements of relative permeabilities to oil and gas on small core samples of reservoir rock by five methods, and describes the influences of such factors as boundary effect, hysteresis, and rate upon these measurements. The five methods used were the "Penn State," the "single core dynamic," the "gas drive," the "stationary liquid," and the "Hassler" techniques. In those methods in which the results are subject to error hecause of the boundary effect, the error may be minimized hy the use of high rates of flow. In order to avoid complexities introduced by hysteresis, it is necessary to approach each saturation unidirectionally. Observed deviations of relative permeabilities with rate can be explained as a manifestation of the boundary effect, and disappear as the boundary effect vanishes. The results indicate that all five methods yield essentially the same relative permeabilities to gas. Of the four methods applicable to the determination of relative permeability to oil, three, the Penn State, single core dynamic, and gas drive, gave relative permeabilities to oil which were in close agreement. The Hassler method gave relative permeabilities to oil which were consistently lower than the results obtained by the other methods. INTRODUCTION The relationship between the effective permeability of a reservoir rock to each of the fluids flowing through it and the corresponding fluid saturation is an important characteristic of the reservoir rock. Knowledge of this characteristic is and gas reservoirs and of the ultimate recovery to be expected extremely important in the prediction of the behavior of oil under various operating conditions. These effective permeabilities are usually expressed as the "relative permeability" to a fluid phase, defined as the ratio of the effective permeability to the permeability of the rock to a single phase at 100 per cent saturation. Relative permeability-saturation relations are not the same for all kinds of reservoir rock, but may vary from formation to formation, and within the different portions of a heterogeneous formation. In studying the performance of a specific reservoir, it is necessary, then, that the relative permeability characteristics of the individual portions of the reservoir be measured. These measurements may be made in the laboratory on small core samples from the reservoir. Various techniques have been proposed for the measurement in the laboratory of relative permeability-saturation relations. In varying degree, difficulties attend the use of all of the methods which have been proposed. It is the purpose of this paper to discuss the factors which influence the measurement of relative permeability, the difficulties encountered in several methods, and to present comparative results obtained by the use of various techniques. FACTORS WHICH INFLUENCE THE MEASUREMENT OF RELATIVE PERMEABILITY It is necessary that the relative permeability data measured in the laboratory yield the same relative permeability-saturation relationships that would govern the flow of fluids through the sample if it were to occupy its original position in the reservoir. Since the core sample upon which the laboratory measurements are made is not surrounded by similar core material as it was in the reservoir, an error in measuring the relative permeabilities may arise from the "boundary effect" which results from a discontinuity in capillary properties of the system at the effluent end of the core. Again, the rates of

Jan 1, 1951

By C. A. WARNER

IN all the meetings of the Petroleum Division, emphasis was placed on the essential importance, in the successful furtherance of our war effort, of efficiently producing, transporting, refining, and utilizing maximum quantities of crude oil and natural gas with the minimum expenditure of critical material. With representatives present from all branches of the petroleum industry, from all parts of the United States, the sessions were opened Tuesday morning with Commander Harry P. Stolz. U.S.N.R., Chairman of the Division, and A L. Haider as associate chairmen. From that time until the symposium on petroleum economics was closed Thursday afternoon papers of exceptional interest and importance were presented and discussed in a most frank and open manner.

Jan 1, 1943

Readers of recent Bulletins have doubtless observed that the problem of improving both material and moral condition of employees is receiving close attention from influential members of the Institute. This will lend interest to certain developments and investigations that have been reported elsewhere.

Jan 5, 1918

By E. C. Houston, R. A. Laurence, F. A. W. Davis, L. L. McMurray, H. S. Rankin

This paper is coodensed from several reports by members of the staff of the Minerals Testing Laboratory of the Tennessee Valley Authority, on a series of experimental tests in the beneficiation of barite of the Valley area. These experiments were conducted upon a large number of samples taken from several mines in three different districts. The area contains numerous producing deposits, nearly all of which are hampered by the high iron and silica content of the ores. Because of the small difference in specific gravity between the iron oxide and the barite, a gravity separation is generally poor. The removal of the iron thus offers a special problem. Some of the operators have turned to magnetic separation to meet the shipping requirements for less than one per cent iron. The present experiments were conducted to determine the application of decrepitation or flotation in simplifying the concentration of the barite by removing the iron oxide and silica in one operation. Practically all the barite marketed in the area has been as "off-color" crude. The bleaching studies were made to determine the bleach-ability of the ores to alleviate this inferior grading, placing them on the market as bleached barite. Geology Barite has been produced at many places in the Tennessee Valley area, and prospects and minor deposits are known at many other places, but practically all the production of barite in the Valley has been from the Sweetwater district of East Tennessee. Other leading areas of former production are the Tazewell-Russell counties areas of southwest Virginia, the Del Rio-Stackhouse district of East Tennessee and western North Carolina, and the Fall Branch district of upper East Tennessee. The areas described in this paper are those from which samples used in the concentration tests were obtained.

Jan 1, 1942

By J. E. Lawver, G. L. Samsel

The success of many mineral dressing processes, including froth flotation and electrical concentration, depends largely on knowledge of physical and chemical structures of the mineral surfaces involved. As a general rule solids have surface layers, usually invisible by optical tests, that differ from the substratum. To the mineral engineer, therefore, a knowledge of the surface structures of minerals is of paramount importance. During the past decade one of the most powerful tools in the study of froth flotation mechanisms has been the use of radioactive tracers, but this technique usually cannot give definite information regarding the chemical changes that may or may not have occurred at the surface. The electron microscope and electron diffraction camera can be particularly useful instruments in surface studies.. An election microscope permits much closer examination of surfaces than can be obtained with a petrographic microscope. In certain cases, it is possible to identify trace quantities formed by chemical reaction between flotation agents and mineral surfaces by the use of a single-crystal, reflection electron diffraction camera. This article describes several instances in which these instruments have been valuable guides in mineral dressing research at International Minerals & Chemical Corp. One of the first applications of these techniques employed by International Minerals was in conjunction with the study of electrical concentration of potash ore. The first reasonably successful separation of potash ore was made by subjecting a sample of the ore to a methanol wash. Subsequent tests using tagged 6C14 methanol showed that only a minute quantity of radioactivity was detectable after the methanol-washed sample had been dried and heated to about 300°F. It was concluded that although some methanol had been held to the surface by adsorption, this could not account for the improved electrification because there was no evidence of methanol selectivity with respect to NaCl or KCl. Consequently there must have been some other change in the surface. Carbon replicas* of the mineral grains were made before and after the methanol wash. The replicas were separated from the minerals by dissolving in water. This extraction replica technique is particularly attractive because the specimen can first be used with the electron microscope to observe the general structure of the surface and can be re-used as a specimen for electron-diffraction studies to identify any solvent insoluble material present on the mineral surface." Fig. 1 shows the general

Jan 1, 1960

By J. W. Whitlow, P. K. Theobald, W. C. Overstreet

Monazite placers in a region of the Carolinas ex- in 1951-1954 by the USGS are estimated to contain at least 53,000 short tons of thorium and 4600 short tons of uranium. None of these deposits is being mined. The 5200-sq mile area investigated extends northeast along the western Piedmont from the Savannah River in South Carolina to the Catawba River in North Carolina. Much of the region is 700 to 1100 ft above sea level. Gentle hills and broad interfluves give a local relief of 100 to 200 ft. This increases to 1700 ft at the west margin of the area where the east flank of the Blue Ridge is approached in South Carolina and the South Mts. are entered in North Carolina. This report is restricted to placers in the Piedmont. Monazite deposits in the Blue Ridge and coastal plain were not covered by the investigation. Monazite Mining in the Carolina Piedmont: Discovered in 1879 by W. E. Hidden,' the monazite placers in the Carolina Piedmont were first mined in 1886. The area was a major world source for thorium and the lanthanides until 1895, when Brazilian monazite entered the trade. Total output from the Carolina Piedmont has been nearly 5500 tons of monazite,2 but the placers have been idle since 1911, except for 48 tons produced between 1915 and 1917. Monazite mining was revived in the Carolinas in 1954 when a dredge operated by the Heavy Minerals CO. opened a fluviatile placer along Horse Creek in the coastal plain near Aiken, S. C. Geology and Mineralogy: Two recent papers",' have described the geology of the monazite placer district in the Piedmont between the Savannah and Catawba rivers; the general geology of the region has been reviewed by P. B. King.' These reports show that the placers are in locally derived alluvial sediments that cover the floors of shallow, narrow valleys in an area underlain by monazite-

Jan 1, 1960

By T. Smales, P. L. Wright, K. Barron

The results of field measurements using an air injection technique to investigate the integrity of three pillars in the Mclntyre Mines Ltd. 114 seam at Crande Cache, Alberta, are reported. These pillars are shown to be stable and an estimate is made of the strength of these pillars. Using these results, together with Hustrulid's pillar strength formulae, a general pillar strength equation for the 114 seam is developed. This equation takes into account the probability of failure that may be deemed tolerable within the design requirements. The variation of the minimum pillar dimensions with depth below surface for uniform pillar layouts is then examined for a range of tolerable failure probabilities. A general equation of the form B = 2.60 +B Z relates the minimum pillar design width, B metres, with the overburden depth, Z metres, where B is a parameter related to the tolerable failure probability. This equation only applies for 3.05m high pillars with 6.lm wide entries. Finally, the question of what failure probability is tolerable within the design of mine pillars is discussed. This will depend on the support role required of that pillar and the anticipated period over which the pillar must perform that role. Five categories of coal mine pillars are defined, each with a somewhat different role to perform. Tentative design criteria in the form of "tolerable probabilities of failure" are suggested for four of these five categories of pillar. The fifth category of pillar has no reliable support function to perform and support must be obtained by other means.

Jan 1, 1983

By Richard W. Lodge

Several methods, both wet and dry, for the assay of zinc-box residues from the cyanide process, have been described in recent years, and each of them has been claimed to be superior to all others. In the year 1901, a paper, entitled "Assay of Zincy Precipitates," was published ill the School of Mines Quarterly to the purport that the scorification method for the assay of zinc-box residues was absolutely unreliable. In order to shed light on this matter, the following experiments were undertaken by Messrs. C.B. Hollis and F. D. Kehew, undergraduate students at the Massachusetts Institute of Technology. The zine-box residues used were obtained through the courtesy of Mr. H. R. Batcheller. The samples were very rich and varied greatly in the fineness of their condition. SCORIFICATION-ASSAYS. In the preliminary tests, the charge, which was weighed on a chemical balance, consisted of 0.1 Assay Ton of residues mixed with from 30 to 35 grammes of test-lead and placed in a 3-in. scorifier, over this an additional quantity of test-lead (from 30 to. 35 grammes) was placed for a cover, and borax-glass, varying in quantity from 3 to 15 grammes, was sprinkled over the top of each charge of the various assays for a cover. The charges were scarified in a muffle-furnace heated to the ordinary temperature which is used in scorification; in some cases the door of the muffle was left open, while in others it remained closed. Generally, the charges spit badly, especially in the assays that were made with door of the muffle left open, or in those in which the door was opened too quickly. The results of the preliminary assays showed: 1. That in order to obtain approxi-

Jan 1, 1904

By H. S. Rankin, F. A. W. Davis, R. A. Laurence, L. L. McMurray, E. C. Houston

This paper is coodensed from several reports by members of the staff of the Minerals Testing Laboratory of the Tennessee Valley Authority, on a series of experimental tests in the beneficiation of barite of the Valley area. These experiments were conducted upon a large number of samples taken from several mines in three different districts. The area contains numerous producing deposits, nearly all of which are hampered by the high iron and silica content of the ores. Because of the small difference in specific gravity between the iron oxide and the barite, a gravity separation is generally poor. The removal of the iron thus offers a special problem. Some of the operators have turned to magnetic separation to meet the shipping requirements for less than one per cent iron. The present experiments were conducted to determine the application of decrepitation or flotation in simplifying the concentration of the barite by removing the iron oxide and silica in one operation. Practically all the barite marketed in the area has been as "off-color" crude. The bleaching studies were made to determine the bleach-ability of the ores to alleviate this inferior grading, placing them on the market as bleached barite. Geology Barite has been produced at many places in the Tennessee Valley area, and prospects and minor deposits are known at many other places, but practically all the production of barite in the Valley has been from the Sweetwater district of East Tennessee. Other leading areas of former production are the Tazewell-Russell counties areas of southwest Virginia, the Del Rio-Stackhouse district of East Tennessee and western North Carolina, and the Fall Branch district of upper East Tennessee. The areas described in this paper are those from which samples used in the concentration tests were obtained.

Jan 1, 1942

By Richard E. Gray, William S. McCann, Robert C. Speck, Robert W. Bruhyn

Subsidence of the ground surface is the inevitable result of high recovery longwall and room and pillar coal mining operations. Up to now, U.S. research into this phenomenon has been concerned primarily with documenting the magnitude and extent of ground movements and prediction of the attendant ground strains through traditional ap¬proaches that have been developed in Europe and the United Kingdom. Preoccupation with ground strain prediction has, unfortunately, diverted attention from the more meaningful objective of predicting the severity of damage to structures at ground surface and the prob¬able cost to repair such damage. An attempt has been made to rectify this situation by reviewing in detail one hundred thirty four cases of subsidence damage to dwellings above active mines in western Pennsylvania, identifying the types of damage and the circumstances under which damage took place. The data reveal that damage to dwellings virtually always includes basements in addition to the readily apparent effects to the superstructure. In 90 percent of the subsidence cases, more than half the repair cost is associated with damage to subgrade components. A damage classi¬fication system has been devised that relates observed damage to severity and repair cost in a uniform manner for conditions in the Northern Appalachian Coal Field. Damage severity has been examined in the context of depth to the mine, the character of the near¬ surface overburden materials, mining type and other parameters.

Jan 1, 1983

By Robert Sisselman

If we are lucky," says Hollis M. Dole, Assistant Secretary of the Interior, "coal, uranium and hydropower will provide us with maybe a third of the energy we require in 1985. The other two- thirds will have to be made available in liquid and gaseous form." Luck, however, may have run out, for if the facts and figures relating to supply and demand of natural gas over the next 20 years prove accurate, the United States may fall short in its attempts to bring the energy crisis under control. By the year 1990 the world will need to consume a minimum 150 quadrillion Btu of energy with gas requirements running as high as 42-43 trillion cu ft. By 1990, the U.S. alone will require 45-46 trillion cu ft. To meet anticipated demand, this country will have to overcome a deficiency of about 20 trillion cu ft since, by all pragmatic estimates, it will produce only 15-20 trillion cu ft of gas. The importation of natural gas into the U.S. will help but will not solve the problem. Adequate gas supplies will have to be supplied domestically. The Arctic, with its predicted huge reserves of gas, combined with imports of liquid natural gas (LNG) may provide as much as 15% of the 45-46 trillion figure, however, such reserves will not come into play as quickly as originally thought. The Alaskan gas fields, for instance, will provide a substantial supplement to domestic gas needs, but only after 1976.

Jan 10, 1972