Search Documents

By L. W. Holm, G. G. Bernard

Laboratory experiments were conducted to determine the effect of foam on gas flow in porous media. Previous studies have indicated that foam may be applicable as a restrictive agent in influencing underground gas flow. Foam was found to be exceedingly effective in reducing the permeability of porous media to gas. Consolidated and unconsolidated sands with specific permeabilities of 100 to 146,000 md had, in the presence of foam, gas permeabilities that were less than 1 per cent of the specific permeability; in many cases the gas permeability was practically zero. Foam reduced the gas permeability of loose sand to a much greater degree than that of a tight sand. For example, the permeability of a 125,000-md sand was reduced to 3 md while the permeability of a 4,000-md sand was reduced to 7 md. This effect should cause, to some degree, selective plugging of high permeability channels in various oil displacement processes. The presence of oil in a porous medium decreased the effectiveness of foam in reducing gas permeability; apparently oil acts as a foam depressant. However, it was found that certain foaming agents were very effective in reducing permeability even. in the presence of oil. Also, continuous injection of other foaming agents increased their effectiveness, when oil was present. The effect of foam on permeability of porous media to gas was studied as a function of foaming agent concentration and injection rate, absolute permeability, total pressure, pressure gadient, length of porous system, brine concentration and time. INTRODUCTION The use of surface active agents in flood water to increase the recovery of oil has been studied in the laboratory and in the field for decades, with rather limited success. In recent years a new approach to the problem was proposed. Instead of using an aqueous solution of surfactant as an oil recovery agent, Bond and Holbrook2 proposed that the oil recovery agent be a mixture of surfactant solution and gas. In their method, a water-soluble surface active agent with foam-producing characteristics is injected into an underground formation as an aqueous slug. This slug is followed by gas to produce a foam within the rock. Foams are defined as "agglomerations of gas bubbles separated from each other by thin liquid films'! A foam is fundamentally an unstable system. The foam process for oil recovery has since been studied by other investigators. Fried 1 has shown that foam can displace from porous structures oil that normally is unrecoverable by conventional water or gas drives. This superior oil displacing action is believed to be the result of several factors: (1) foam introduces into the reservoir many resilient interfaces of various sizes and curvatures, which increase the probability that a proper combination of forces for oil displacement will be created; (2) foam has appreciable viscosity which improves mobility ratio and contact efficiency; (3) foam accentuates the trapped gas effect because high gas saturations are possible without producing high gas/oil ratios. Deming4 studied the effect of various foam properties on the displacement of liquid. He found that (1) high foaming ability favors high displacement efficiency; (2) high foam stability is not necessary for high displacement efficiency; (3) displacement efficiency decreases with increase in plasticity of foam and (4) displacement efficiency is unaffected by surface tension of foaming agent solution. One of the important aspects of this oil recovery process is the effect of foam on gas permeability. The simultaneous flow of gas and liquid in porous media has been studied by numerous investigators and a large amount of literature exists on the subject. In this previous work, gas and liquid have generally been considered as essentially independent phases, whose flow characteristics are related through the saturation parameter. Foam, however, is a material with properties that are considerably different from those of its components; for example, the viscosity of a foam is greater than either of its components. Gas flow in a porous medium in the presence of foam should be considerably different

Jan 1, 1965

By Dennis H. Laubscher

INTRODUCTION The selection of mass mining methods is the situation facing not only planners of new operations, but also those involved with cur- rent operations, including the eventual change from open-pit to underground. Increasing ground control problems on many mines, plus a better understanding of dilution and ore loss problems have meant a review of current mining methods and support techniques. Experiments are only successful if conducted in the right mining environment and on the right scale. Mining personnel have been known for their conservatism and will tend to persevere with an established method rather than change; often, hidden costs will obscure the correct economic assessment. An established mining sequence is not necessarily correct in the long term. However, recommendations to change are usually met with opposition because of inconvenience, temporary production problems and the desire for a trouble-free guarantee. In any planning exercise, care must be taken that time and money are not wasted in trying to achieve the unattainable. During the decision-making period, production personnel must be involved, and, if possible, they should visit similar omrations to that proposed. Co-operative production personnel will help ensure success. Descriptions of mining methods are available in technical papers and books, and it is not intended to discuss this aspect, but, rather, the various factors which must be recognised before arriving at a final selection. In another paper presented at this Conference (Heslop and Laubscher, 1981) factors affecting ore recovery and dilution are discussed in greater detail for various cave mining methods. PRELIMINARY CONSIDERATIONS Comprehensive Geological Data. Geological information is available during the exploration stage, but, often, core from exploration drilling is not analysed with the selection of a mining method in mind. Drilling costs are high, therefore the maximum benefits must be derived from this operation. Holes which have not intersected ore may provide data on possible shaft sites, and 35 mm colour slides of core, sound logging and geomechanics classification, will provide a record which can be used with confidence at a later date. Intersections of the various rock types should be kept for future study; for example, is weathering likely to be a problem, bearing in mind that this can be accelerated in the warm, humid atmosphere of an underground mine. The accumulation of data required to select a mining method starts with initial geological work in the target area, whether this be surface mapping or a diamond drill hole. Publications. As technical papers, reports and books are used in the selection of mining methods, an appeal is made to authors to describe the geological environment so that readers can relate to their own conditions. Not enough emphasis is given to the problems experienced and the techniques employed to overcome them. Follow-up papers are seldom written and we should be prepared to discuss our failures. Diagrams are often misleading, as the ideal and not actual situations are depicted. The caved ore/waste interface is not a straight line, and whereas this may not be significant in a diagram of a 200-117 draw height, it certainly is in sub-level caving with draw zones only 1 - 2 m width but up to 20 m high. SUMMARY OF FACTORS AFFECTING THE SELECTION OF UNDERGROUND MASS MINING METHODS (a) Regional rock stresses and mining geometry. (b) The geomechanics rock mass classification of the orebody and surrounding rock mass. (c) Ratio of the surface area of the ore/unpay interface to the contained ore which determines ore losses and dilution. (d) The cavability and fragmentation data of the ore and hangingwall. (e) The mineral distribution in the orebody and its dilution zone.

Jan 1, 1981

By H. Hooykaas

A few years ago Marsal published a method of predicting oil recovery as a function of time for an edge-water-drive reservoir with several rows of wells.' The method is based solely on oil- and water-production data obtained during a short period for the first row of wells and the gross productions (past and future) of all wells. This paper presents a streamlined version of the original publication and experimental evidence showing the reliability of this version. For this purpose scaled experirnents were performed in a large model (750 X 500 X 23 cm, 24.4 ft X 16.2 ft X 8.9 in.) in which edge-water-drive reservoirs with three rows of production wells were simulated. From the results of the experiments it is concluded that the method gives a fairly accurate prediction of the future production behavior of the reservoir and enables us to select the most profitable production plan. Results obtained with the method were always slightly conservative. INTRODUCTION The calculation method developed by Marsal aims at forecasting future reservoir behavior.' It can be applied to floods in which a number of down-dip wells are rapidly going to water. Essentially it is a method for predicting the future behavior of the up-structure wells on the basis of the observed behavior of the down-structure wells. As such, the method is especially useful for predicting behavior of edge-water drives toward several rows of wells. The requirement to be met for justifying the approach is identity of production mechanism in all regions of the reservoir. The attraction of the method then lies in the fact that it applies even when we have no complete description of the prevailing production mechanism. The original publication was in the German language and for this reason, perhaps, did not attract widespread attention. In our opinion it deserves to do so because it does offer in a simple way results which are in fair agreement with observed data. The aim of the present paper is to bring the method to the attention of a wider audience. The method in its most simplified form is reviewed and experimental data in support of it are presented. PRINCIPLES To show Marsal's principle. we will first write the continuity equation for very simple conditions, linear flow (in the positive x-direction) in an incompressible porous body [cross-section A(x), porosity +(x)], saturated with incompressible fluids (oil saturation S). When the oil in this formation is displaced by water, injected at x = 0 (inlet face), we get where q(t) is the total gross displacement rate and f the fractional oil flow. The equation can be solved if we make the assumptions: (1 ) that the fractional oil flow (f) is a univalent function of saturation (S); and (2) that the function is the same throughout the porous medium. Then: f = f(S) Solving this equation with the method of characteristics, we obtain

Jan 1, 1966

By L. W. Holm, A. K. Csaszar

A series of laboratory experiments was conducted in which oil was displaced from a porous medium by water-driven slugs of alcohols or similar solvents. The solvents used were soluble to some degree in both oil and water and covered the range of solubilities from complete solubility in oil to complete solubility in water. Displacement experiments were conducted on 2-and 3%-in. in diameter consolidated cores and 1-and 2-in. in diameter unconsolidated sand packs. The cores and sand packs ranged in length from 1 to 30 ft, and they were saturated with brine and crude or refined oils. The solvents used included ethyl alcohol, isopropyl alcohol (IPA), tertiary butyl alcohol (TBAI, secondary butyl alcohol (SBA), n-amyl alcohol (NAA), methyl ethyl ketone, acetone and others. It was found that all of the oil present in a porous medium could be miscibly displaced by injecting a slug of mutual solvent and driving it with water. The oil-recovery efficiency was dependent upon (1) the relative solubilities of the solvent in oil and water, and (2) the distance traversed by the flood. For complete oil recovery from cores, a smaller amount of a preferentially oil-soluble solvent was required, compared to the amount of preferentially water-soluble solvent needed. The size of the solvent slug required varied inversely with the linear flooding-path length raised to the 0.65 power. Water-driven dual solvent combinations (an oil-soluble solvent slug followed by a water-soluble solvent slug) were found to effect complete oil recovery with less total solvent than any single solvent used. In these dual-solvent displacement experiments, the slug size required varied inversely with length raised to the 0.55 power. Based upon the experimental results, a theory was developed to describe the displacement of oil and water by mutual solvents, and equations are presented to predict the production history in a linear system. These equations take into account the properties of the solvents and the porous medium. INTRODUCTION Oil-recovery processes which utilize displacing fluids that are miscible with the reservoir fluids have been studied extensively in recent years. Because of the poor contact efficiency and high pressure requirements of the LPG-gas displacement process there has been considerable interest in the alcohol-water process, and a number of studies have been made on the recovery of oil through the use of solvents which are mutually soluble in oil and water. An investigation by Sievert, Dew and Conleyl indicated that the use of mutual solvents would be limited because the presence of water in a porous medium would cause a phase break in the leading edge of the displacing solvent. Their study also showed that, in consolidated cores containing. only oil, the displacement of oil by a water-driven mutual-solvent slug of tertiary butyl alcohol (TBA) was affected by the viscosity ratios of the fluids involved. Gatlin and slobod3 concluded that an isopropyl alcohol (IPA) slug acts as a miscible piston, completely displacing both oil and water until the alcohol content of the mixing zone falls below the concentration necessary to maintain miscibility. Their study was conducted on uniform unconsolidated sand packs. They concluded further that IPA could be used effectively to recover oil from a watered-out sand. In a paper by Taber, Gamath and Reed4 relating an investigation on sandstone cores, it was stated that the displacement of oil by mutual solvents, particularly IPA, was not a miscible displacement and that no improvement in efficiency could be expected with increase in flooding-path length. However, their analytical analysis of the displacement mechanism using TBA is, in fact, one which indicates that the displacement is controlled by miscible mixing. They suggested that the lack of improvement in efficiency with flooding - path

By Carl F. Floe, Michael B. Bever

ACCELERATED by the demands of war, research and development work in nonferrous physical metallurgy has continued at a rapid pace during the past year. In particular, advances have been made in processing and fabrication, especially of the light alloys, and in the surface treatment of metals. Theoretical physical metallurgy, although less active, has not been neglected and the year has brought forth some -notable contributions to our understanding of the fundamental structure of metals and their behavior in service. Of course, much work that has been done cannot be publicly discussed because of wartime restrictions.

Jan 1, 1945

By F. W. Willard

VIEWING with alarm is a preoccupation not exclusively the habit of the political spellbinder. In good faith many of our mineral technologists have been and are genuinely alarmed over the prodigal consumption of our mineral reserves. Most competent observers are cautiously pessimistic. There are sound technical reasons for such caution. It is the purpose of this paper to discuss some of those reasons without benefit of a gift of prophecy. Perhaps the outstanding reason for caution is ignorance of accessible but undiscovered mineral reserves. The petroleum technologists have an edge on their metallurgical brothers for they have better tools for exploration. This is not to say that the mining geologist has to depend on hunches or the divining rod. The outstanding work on orogenesis by Lindgren and others has provided the mining geologist with some sound scientific knowledge as to where accessible metallic minerals are most likely to be found, As Clinton H. Crane has recently observed, most of the accessible areas of the earth have been combed for easily identified outcrops, and those have been or are being actively exploited. To find ore bodies hidden below the surface is still a costly speculation.

Jan 1, 1946

By M. D. Hassialis, C. G. Myer

THE nature of a collector-coated mineral surface has been the subject of some experimentation and much speculation. Various aspects of the problem have been isolated and studied; it is probable, however, that there exist aspects as yet unrecognized, which are needed for a complete description of the system. The recognized elements of the problem are: 1—The nature of the chemical units comprising the film and the nature of the forces holding these chemical units to the mineral surface; 2—The orientation of the chemical units at the surface; and 3—The disposition of the collector units at the mineral surface. This report touches upon all three aspects of the broad problem; it deals, however, with a new and heretofore unrecognized element—the mobility of the collector units in the two dimensions of the solid-liquid interface. Regardless of the viewpoint adopted as to whether the chemical units comprising the collector film are collector ions or molecules, held either by chemical or physical forces, the writers on flotation theory are in apparent agreement as to the orientation of the chemical units at the mineral surface. Wark and Cox' showed that the contact angle at a stable collector-coated surface in a constant chemical environment is independent of the nature of the mineral and of any resurfacing agent; it depends solely upon the collector used. They showed further that the value of the contact angle increases with the number of carbon atoms in a homologous series of compounds. Taggart, Taylor, and Knoll2 postulated that the collector ion is oriented with the chemically reactive, polar end toward the mineral surface and the non-polar, hydrocarbon-like end toward the liquid phase. In support thereof they cited the abstraction of p-p1 dihydroxydiphenylthiourea and of glycol xanthate8 by galena without a concomitant increase in the contact angle above that of clean galena. It was argued that in these cases the water-repellent layer which normally would be presented to the liquid phase owing to the orientation of the collector ions is overlain by a layer of water-avid groups, the hydroxyl groups. Implicit is the analogous orientation exhibited by a monomolecular layer of an insoluble substance at an air-water interface. It should be pointed out that these facts also are consistent with the concept that the collector units be flat on the surface of the mineral and that the response of the surface to an air bubble is determined by the ratio of the area covered by water-avid groups to the area covered by water-repellent groups; the areas being weighted according to the relative watef-avidity or water-repellency of the groups involved. The disposition of the chemical units of the collector film at the mineral surface has not received the attention it merits. Taggart4 concluded from the observed stoichiometry of the ions entering and leaving a surface that the stoichiometry is obeyed in detail at the surface of the mineral. Thus, in the case of xanthate-coated galena, pairs of xanthate ions are attached to surface lead ions. In the case of chemisorption, Gaudin and Preller postulated an agreement between the atoms or ions of the substratum (the mineral surface) with those of the superstratum (collector film); in the case of the physical adsorption their position is not clear. In one place they state "the first type (physical adsorption) does not require any agreement between the atoms or ions of the substratum with that of the superstratum" and in another place that "It seems, in fact, as though some slight influence of the substratum is formed even in physical adsorption." The present work shows that in some cases of chemisorption the chemical units of the collector film are in constant surface-bound motion and may not be assigned to any site of the surface, hence there is no permanent association between the chemical units of the film and the atoms or ions of the solid. The physical property of the collector film that is of paramount importance is its surface energy. Although this property is not susceptible to direct experimental determination, the related contact angle is. Much of the knowledge of the properties of a collector film derives (by deductive and inductive reasoning) from the behavior of an air bubble thereat

Jan 1, 1952

By Hsun Hu, R. S. Cline

The formation of annealing textures during the course of recrystallization in 2 pct Al-Fe crystals rolled in the (111) [112], (112) [111], and (112) [Till orientations has hem studied in detail. When the rolling texture is composed of both (111) [121] and (001)[110] components, the annealing texture consists of mainly (110) [001] and (113) [332] components. As the (001) [110] component diminishes from the surface to the interior of the rolled crystal, the relative concentration of the (113) [332] component in the annealing texture decreases accordingly, whereas that of the (110)[001] component increases with the (111)[112] component in the rolling texture. Such dependence of the annealing texture on the composition of the rolling texture is in accmdance with the oriented growth mechanism. Grain-growth characteristics during recrystallization, hence the annealing texture, can he considerablv different in (112) [111]-type crystals depending sensitively on the initial orientation of the crystal. In a previous publication,' the formation of rolling textures in 2 pct A1-Fe single crystals with initial orientations of approximately (1ll)[112], (112)[111], and (112)[111] was studied in detail. The deformation texture of these crystals consisted of either a single (111)[112] or a combination of (111)[112] and (001)[110] components in various concentrations. For the (lll)[112] crystal, the deformation texture was a single (lll)[112] up to 70 pct rolling reduction, but it became (lll)[112] plus (001)[110] after -90 pct reduction. For the (112)[113.]-type crystals, the relative concentration of the (111)[ 112] and (001)[110] components varied with the depth below the surface of the crystal, as well as with the amount of deformation. These series of specimens, having deformation textures with a range of concentration of the (111)[112] and (001)[110] components, could therefore be used for a thorough investigation of the effect of deformation-texture components on the formation of annealing textures. In a study of rolling and annealing textures in Si-Fe crystals, Dunn and Koh3 noted that the addition of a (001)[110] component to the (111)[112]-type deformation texture had practically no effect on the recrystallization texture.* According to the ori- ented growth mechanism for the formation of annealing textures, nuclei related to the deformation texture by approximately 30-deg rotation around a common [110] axis have the highest rate of growth and the resulting annealing textures generally have such an orientation relationship with respect to the deformation textures.314 It was reasoned by Dunn and Koh3 that if the oriented growth mechanism operated the recrystallization texture developed from a deformation texture containing both (111)[112] and (001)[110] components should be strongly centered around (113)[332], because (113)[332] is approximately midway between the (111)[112] and (001)[110], and is related to both of these two orientations by [110] rotations of 25 to 30 deg. Hence, nuclei of (113)[332] orientation should have a high rate of growth in the deformed matrix. However, their results were not in accord with this prediction. It was felt by the writers that a detailed study was needed to clarify the effect of deformation-texture components on annealing-texture formation. For this reason, the present investigation was conducted. EXPERIMENTAL PROCEDURE Specimens used for the present investigation were taken from the crystals rolled previously for deformation-texture studies.' In order to follow the progress of annealing-texture formation during the course of recrystallization, a single specimen was taken from each rolled crystal and its textural changes examined after successive anneals until recrystallization was complete. The specimen was carefully cut from the rolled strip with a jeweler's saw. Prior to annealing, the sawed edges were etched to remove distorted metal, while both faces of the specimen were protected from the etching solution by acid-proof plastic tape. After annealing, the specimen was etched from the "bottom" face only (the reference or "top" face of the specimen was protected by plastic tape) to one half of its original thickness, so that the texture at the surface and at the central section of the strip could be determined by the reflection technique. The

Jan 1, 1965

By Robert U. King, John W. Vanderwilt

THE Climax molybdenite deposit in Lake County 100 miles southwest of Denver is located in the central part of the mineral belt extending northeasterly across the state. Principal geographic features and geology are shown on Fig. 1. The first period of molybdenite mining, which began in 1918, ended in April 1919 because of limited demand and a price drop to about 72¢ per lb. During this time the ore came from the Leal level and surface outcrops at a higher elevation. Rate of mining was 250 tpd and several million tons of ore averaging 0.7 pct molybdenite were developed. Since April 1924, when the second period* began, Climax Molybdenum Co. has been the only operating company. Production in 1924 was 400 tpd and finding ore was a continual problem. When the White tunnel was extended, however, further ore was encountered. The orebody was thought to be tabular until 1926, when B. S. Butler recognized the relation of the developed ore on the Leal and White levels to a central area of fine-grained hydrother-mal quartz, and by 1929 diamond drilling had blocked out indicated ore reserves in excess of 100 million tons. In 1946, on the basis of information obtained from 25 miles of mine workings and a completed exploratory program involving over 200,000 ft of diamond drilling, the present authors reviewed and brought up to date the geology of the orebody. More recently Sears," employing microscopic techniques, made a study of hydrothermal alteration and mineralization, and Howell and Schassberger'" restudied available geologic data. Production (1953) of molybdenite ore has been expanded to over 25,000 tpd and total production from 1918 through 1953 has been: Tungsten, tin, and pyrite are byproducts and monazite also was produced from 1949 through 1951, after which it was not saved. A maximum of 15 to 20 tons of monazite was produced. Geology of the Area Pre-Cambrian crystalline rocks constitute most of the Mosquito Range for several miles to the north, east, and south of the Climax molybdenite deposit, see Fig. 1. To the west the crystalline rocks are in fault contact with shales and sandstones of Pennsyl-vanian age. Both crystalline rocks and sediments are intruded by dikes and sills of Tertiary age. Numerous faults with small displacements are to be found in the crystalline rocks east of the Mosquito fault and in the sedimentary beds to the west. Pre-Cambrian Rocks: The pre-Cambrian rocks consist of schist and gneiss, identified with the Idaho Springs formation, and granite with minor pegmatite correlated with the Silver Plume granite of the Silver Plume area. The Idaho Springs formation is a general term applied to pre-Cambrian schist and gneiss found over a large part of the Colorado Front Range. At Climax this formation consists largely of biotite-schist and quartz-biotite gneiss with minor quantities of plagioclase and orthoclase, although in places appreciable quantities of feldspar and quartz are present in the more gneissic varieties. Locally, especially along the contact with granite, recrystal-lization of the schist has produced coarser texture and a more pronounced than average gneissic appearance. The gneiss and schist have been mapped as a single unit by Butler and Vanderwilt (1933)" and by Singewald (1951).12 Schist predominates at the higher elevations of the Mosquito Range and in the area to the north and east of Climax. The regional trend of schistosity is northeast with varying dips to the east. Silver Plume granite and associated pegmatite intrudes the Idaho Springs formation. Silver Plume granite in many places and in the Climax district in particular has an irregular form, and many large and small inclusions of schist and gneiss occur within the granite. Granite predominates at the surface in the immediate vicinity of the area of hydrothermal alteration and extends for several miles to the northeast and southeast. As more schist is present at lower levels of the mine than in the upper levels, the suggestion is that the granite is sill-like in form,

Jan 1, 1956

By James K. Gluck, William E. Galloway, Gary E. Smith, John P. Morton, Christopher D. Henry

INTRODUCTION Surface mining and in situ leaching of uranium have the potential to alter ground-water quality around mines and leach sites. Of particular concern is the fate of uranium and its associated trace elements: molybdenum, arsenic, and selenium. We wish to under- stand the natural processes that control trace element concentrations in ground water and how these processes will influence dispersion of the elements from a mineralized zone, both naturally and during and after mining or restoration. For example, it is commonly recognized that the trace elements are soluble in oxidizing ground water but are insoluble, and can be precipitated, in reducing ground water. Thus oxidizing, metal-bearing water leaving a deposit could re- enter reduced ground, causing the water to be re- reduced and the trace elements to be, reprecipitated. In a sense, this is recreating the original mineralization process. To accomplish the above goals, we have (1) examined the theoretical controls of concentrations based on the available geochemical and thermodynamic data, (2) determined the major ion composition and oxidation-reduction status of Oakville waters because of the influence of these factors on trace element solubility, and (3) determined trace element concentrations and distribution in Oakville ground water. The last approach is used to evaluate how well actual behavior follows predicted behavior. This report focuses on two elements, uranium and molybdenum, because they exemplify the results obtained. The report also is restricted to a regional study of Oakville ground water. Results of more de- tailed study in and around major uranium districts in the Oakville and much of the raw data that support the conclusions in this report are presented in Galloway, Henry and Smith (1980). This report is part of that larger study, which concerned the depositional systems, hydrology, and geochemistry of the Oakville. The U.S. Environmental Protection Agency funded the study, under grant numbers R-805357-01 and R-805357-02. Theoretical controls were determined by reviewing the available literature on aqueous chemistry and behavior of uranium and molybdenum. To aid in under- standing water chemistry, Oakville water analyses were run through a modified version of the computer model WATEQF (Plumer, Jones, and Truesdell, 1976). WATEQF calculates speciation of dissolved ions and determines saturation with respect to a variety of minerals. In the discussion below, ion activity products (IAP) are compared with the equilibrium constant (KT) for various reactions and mineral products. Values of log IAP/KT near zero indicate that the water is in equilibrium with a mineral. Values less than -1 indicate considerable undersaturation and values greater than +1 indicate oversaturation. Galloway, Henry, and Smith (1980) give a more complete discussion of the application of this approach to Oakville water chemistry. Eh-pH diagrams have been constructed or adapted from the literature to predict what form -- dissolved ion or stable mineral species -- uranium and molybdenum assume under various conditions. Construction of the diagrams has followed procedures described by Garrels and Christ (1965). This approach is particularly appropriate because the solubility of the elements is Eh-dependent, and Eh varies greatly within the Oakville aquifer. A number of assumptions or approximations are inherent in the use of Eh-pH diagrams and chemical models such as WATEQF and in the interpretation of water chemistry in general. Both Eh-pH diagrams and chemical modeling rely entirely upon available thermo- dynamic data, including free energies of formation and dissociation constants for various reactions. These values are known to varying degrees of accuracy. Most major ions and minerals are relatively well control- led; however, data for trace metals are much poorer. Thermodynamic data are not available for some minerals, and for other minerals, two or more divergent values exist. By necessity, we have relied on the judgment of others to evaluate thermodynamic data. Calculations by WATEQF and constructions of Eh-pH diagrams are based on an assumption of equi1ibrium. Equilibrium may not be comnon in low-temperature aqueous environments; at best, ground-water composi tion may be in a state of dynamic equilibrium, continuously changing due to changes in environmental conditions. Eh-pH diagrams show what phases are stable at equilibrium under given conditions; they do not prove that the phases actually exist. Many minerals persist or form metastably under conditions outside their equilibrium stability field. The kinetics of reactions, which cannot be evaluated here, are important in determining what phases occur. Kinetics may be less of a problem for ground water that travels and evolves slowly through a semihomogeneous matrix than for many other natural systems. Eh-pH diagrams show equilibrium fields only of phases included. They do not indicate anything about stability relative to phases not included in the diagram. WATEQF, obviously, cannot calculate the degree of saturation of a mineral not included in the program or for which the appropriate ions were not analyzed. Thus, a mineral that was not considered may be the most stable phase under a given set of conditions and may control the solubility of a trace element. Also, this study is limited exclusively to in- organic compounds. Organic material is known to be an

Jan 1, 1980

By William Phillips

This paper was prepared at the request of Capt. A. F. Lucas, Chairman of the Institute's Committee on Petroleum and Gas, as a preliminary discussion of the fuel oils which are used-in the Southwest, giving their composition, uses, prices, etc. Should it afterward be found desirable, these observations may be extended over a larger area. In this connection, J suggest that samples of all kinds of fuel oils, including various tars, from all over the country, be collected and sent to some testing laboratory for examination. We would be glad to extend the facilities of the laboratory of the Bureau of Economic Geology and Technology, at the University of Texas, for this purpose, and to do the work free of all expenses. After such examinations are made and the results classified and studied, it would be possible to suggest specifications under which fuel oils should be purchased, and to arrive at some conclusions respecting the uniformity of such specifications, with due allowance for climatic and other more or less local conditions. While such specifications do not now depart from a common standard anything like as much as specifications for illuminating oils do, yet there are discrepancies which should not exist. Some of these discrepancies are of lessening importance, due to the pronounced tendency to distill every crude oil that can be distilled with profit, and to send residues into the market for fuel oil. Residues from the refineries are of a more uniform chemical composition and physical nature than many of the crude oils that go direct into the fuel market. The lower flash-point oils are disappearing from the fuel trade and in place of them we are getting oils that do not flash below 220° F., nor burn under 320° F. In the Southwest, it has not been long since we had fuel oils that flashed at as low as 110° F., and the average flash point over a considerable period was 151° F. Now we are using oil that flashes at about 30° lower than the former burning point, which was 256° F. In other words, the flash point has risen, on the average, 100°; and the burning point about 75°.

Jan 6, 1914

By R. M. Jorda

The mechanism of parafin deposition and prevention has been studied in the laboratory using an apparatus which provides a quantitative means of studying parafin deposition on metal and plastic surfaces. The amount, hardness, adhesion, per cent wax and mean molecular weight of parafin deposits appear to be governed by surface roughness alone, all other conditions being constant. Tests of various plastic coatings indicate that most smooth, nonparafinic plastics are capable of reducing parafin deposits in oil wells, but flexible, highly polar, nonparafinic plastics are more suitable for providing long term resistance to parafin deposition in oil wells if the flow stream contains abrasive materials. INTRODUCTION The problem of paraffin deposition is one of long standing in the oil industry.' Crude oils often contain paraffins which precipitate and adhere to the liner, tubing, sucker rods and surface equipment as the temperature of the producing stream decreases in the normal course of flowing, gas lifting or pumping. Heavy paraffin deposits are undesirable because they reduce the effective size of the flow conduits and restrict the production rate from the well. Where severe paraffin deposition occurs, removal of the deposits by mechanical, thermal or other means is required, resulting in costly down time and increased operating costs. The troublesome paraffins are normal hydrocarbons ranging from approximately C15H38 to C38H78 mixed with small amounts of branched paraffins, monocyclic paraffins, polycyclic paraffins and aromatics.' The amount of paraffins found in crude oils varies from less than 1 to more than 30 per cent. Many publications are available which deal with this problem, and perhaps the most significant findings in recent literature are contained in a publication by Hunt3 ho developed the "cold spot tester", a really useful means of investigating paraffin deposition. Hunt's observations led to many generalized conclusions concerning the effect of surface roughness on paraffin deposits. He ascertained that there was an observable qualitative correlation between the severity of paraffin deposition and the roughness of the surfaces which he tested (cold rolled steel, stainless steel and several plastics). Because of the number of meaningful observations made by Hunt, his cold spot tester was modified somewhat and extensive tests were per- formed to study the quantitative relationship between surface roughness and the physical and chemical nature of paraffin deposits. LABORATORY TEST PROCEDURES The cold spot test apparatus consists of a flat circular plate mounted on a curved tube and positioned in a vessel containing a wax-oil solution (Fig. 1). The apparatus is arranged so that the temperature of the central portion of the circular plate can be varied by means of a circulating liquid stream; the test equipment includes provisions for maintaining a constant wax-oil solution temperature and stirring speed. In the paraffin deposition studies, the modified cold spot tester was used as follows. The cold spot probe consisted of a flat circular plat 2 in. in diameter and 1/8-in. thick positioned in the wax-oil solution kept at constant temperature. As in Hunt's earlier experiments," a cold liquid was circulated through a tube connected to the circular plate so that the liquid impinged on one side of the plate cooling the plate from the center outward, causing paraffin to deposit on the side of the plate exposed to the wax-oil solution.

Jan 1, 1967

By Robert E. Green, Edmund G. Henneke

Expressions are derived for the orientation factors associated with dislocation damping due to dislocation motion in the basal slip plane. The results of the calculation of these factors for zinc crystals aye pvesepzted and the relevance of these results to ultvasonic-attenuation measuvements is discussed. In this paper expressions are derived for the orientation factors associated with damping of sound waves due to dislocation motion in the basal slip plane of hexagonal crystals. For zinc crystals, the orientation factors for dislocation motion in one slip direction only, as well as for simultaneous motion in all three basal slip directions, have been calculated at 1-deg intervals. The results of these calculations are presented in the form of contour diagrams in a sector of a standard polar coordinate graph. The calculations have been carried out for both the traveling- and the standing-wave conditions. The relevance of these results to ultra sonic-attenuation measurements is discussed. Associated with the calculation of the orientation factors, the modes of elastic-wave calculation were also evaluated, according to the procedure previously employed by Hinton and Green.' The results of these calculations are not presented here since similar results have been reported earlier by Mus-grave.2 However, it should be mentioned that, although the qualitative features of Musgrave's results are preserved, the quantitative values are somewhat altered since different values for the elastic constants of zinc were used. ORIENTATION FACTORS It is convenient to refer to three different sets of coordinate axes, Fig. 1, in the following calculations. First, there are the Miller-Bravais axes which are used in describing the Miller-Bravais indices of planes and directions in a hexagonal crystal. These axes are denoted in the conventional manner by a,, a,, a,, and c. The second set of axes used is a rectangular Cartesian coordinate system located as shown in Fig. 1. Note that the x axis coincides with the close-packed direction al [2110], the z axis coincides with the c axis [0001], and the y axis is orthogonal to these two lying in the [0110 ] direction. Finally, a form of Eulerian angles is used to locate the position of the specimen axis. The angle between the specimen axis and the c axis is denoted by 0 and the angle between the projection of the specimen axis on the basal plane and the a, direction is denoted by ø. The majority of observations on plastic deformation of metal crystals indicates that such deformation is caused by the motion of dislocations on a limited number of crystalline planes and in a close-packed direction. In crystals with hexagonal symmetry the most prominent slip plane is the basal plane (0001) and the slip directiops- are one of the close-packed directions, [2110], [ 12101, or [ 1120]. To properly set the stage for the following work, several points must be clarified. First, we want to consider the contribution to the attenuation of elastic waves by dislocations only. While the Granato-Lucke, model for dislocation damping is presently the one most quoted, it is not necessary to refer the present work to it. The only assumption that need be made is that the motion of dislocations absorbs energy from the elastic wave and therefore attenuates it. It is immaterial here how this energy absorption occurs. However, because dislocations have been observed to move most freely on the (0001) plane for hexagonal crystals undergoing plastic deformation, it will be assumed that it is the dislocation motion on this plane which attributes to the observed attenuation. The basic orientation factor, Ok, is essentially the same as that used by Green and Hinton for fee crystals,4 defined by the equation

Jan 1, 1968

By G. J. Dickman, W. N. Thomas

The factors involved in selecting, a drive system for a grinding mill, including gearing arrangement, motor selection, and electric-supply system limitations are reviewed. Equipment costs are evaluated on a dollar per horsepower basis and starting performance is analyzed, the latter making use of a recently developed computer program. The present interest in large-diameter grinding mills and the rapidly rising cost of the drive in proportion to the cost of the mill establishes a need to explore the drive system in detail. The drive for a 7 to 8,000 hp mill will cost from $350 to $600,000 which represents nearly half the total cost of the mill package, and requires as much building space as the mill proper. Some of the drive components require a longer time to manufacture and the installation time and costs are equal to those for the mill. It is apparent that the drive has become a dominant factor in the overall mill design consideration. A new plant requires a tremendous investment in both time and money. With the high degree of competition in the mining industry, low capital cost is an exceedingly important factor in the development of a project. It is just as important, however, to insure that the equipment is going to perform satisfactorily for the anticipated life of the project without adding unplanned operating, maintenance, and replacement costs. This is the position in which the engineer or designer usually finds himself and is really one of his primary functionsestablishing a realistic compromise between cost and performance. Large primary grinding mills can represent a major portion of the cost of a plant and the drive system accounts for a substantial part of this cost. These facts justify a careful analysis of the drive requirements and all of the factors involved in ultimately arriving at the best system for the lowest cost. A number of excellent papers have been published on various aspects of mill drives. The authors have used information from these papers in making a study of a drive for a 7600-hp, 32 x 12-ft autogenous mill. This was a broad investigation, including mechanical and electrical design, layout, performance, and maintenance considerations, and overall economics leading to the selection of the optimum system for that mill. This paper was developed from the study and includes information applicable to large mills in general. For a successful and economical application, the drive must be considered as a system and all of the components analyzed to determine their effect on the system. This requires the participation of the mill designer, gear, and other mechanical component manufacturers, motor manufacturer, plant designer, and operator. A careful analysis of the mill torque requirements is first necessary to provide a basis for selection of the mechanical and electrical drive components. Because of manufacturing limitations on the size and capacity of gearing available for these low-speed applications, an evaluation of costs for various gear ratios and configurations in conjunction with motor speeds is required. Consultation with the power-supply company is necessary to determine limitations on motor-starting disturbances and to analyze operating costs on the basis of existing rate structures and low characteristics. Finally, consideration must be given to the drive arrangement and its affect on plant layout, space requirements, and location of auxiliary equipment for the selected process. There are presently three basic schemes for driving a mill. The first is a direct drive by a motor operating at mill speed with no gearing. The second is by a higher-speed motor through a trunnion-connected gear drive. The third is by a motor through the more conventional pinion and ring-gear with the option of an interposing gear box to permit greater motor speed than pinion shaft speed. [(Fig. 1.)] Several manufacturers have or are presently developing motors which drive the mill directly without the use of gears. One arrangement has the motor armature intimately surrounding the mill shell-discharge spout or extension of the trunnion journal. The motor stator is then supported independently and surrounds the shell or trunnion-mounted rotor. Another variation utilizes an independent mill-speed motor connected to the trunnion by a drive shaft and flexible couplings.

Jan 1, 1972

By Tell Ertl

TODAY'S mining industry is witnessing a transition in labor utilization. The drill-jumbo operator, the mucking-machine operator, the blasting crew, the scaling and timbering crew are all specialists. The all-around miner is rapidly disappearing. As mechanization has resulted in a higher order of underground skills; specialization of labor has been a natural consequence, as has the need for more supervision and engineering. Mines now are cleaner, neater, safer, and have a greater productivity per man-shift than ever before. Nothing spectacular like the continuous miner has yet come to the underground metal mines, but t a gradual improvement in methods, equipment, and technical knowledge is achieving the increased efficiency. With the exhaustion of the rich ores and large profits and who-cares-about-the-costs, mining has become a business; that of producing low value ores at costs below selling price. Charles A. Chase, patriarch of Colorado mountain mining men, manager of the Shenandoah-Dives, was one of the first to preach and prove his preachings that mining is a business. He has been mining a lead-copper-zinc-gold-silver ore, much from elevations above 1.3,000 ft, for a quarter century without a shutdown.-The ore is of such low value that most engineers and investors still would consider it foolhardy. Yet he has kept Silverton, Colo., alive, has paid wages without a lapse, has produced $25 million of new wealth and maintained a steady return to the investors. This type of responsibility is increasingly apparent in the mining business and is one feather that can be worn proudly. .Much emphasis is being placed on improving, the productive mining operations-breaking, loading and transportation. Breaking in underground metal mining is done by drilling and blasting. To the writer's knowledge, no chain or rotary-type machine has been developed for mining strong, abrasive rock. Drilling Percussion drills are still the standard drilling machines underground. Diamond drills, that: were the rage a decade ago for drilling long holes, are being superseded by the rock drill. The development of the hard abrasion-resistant carbide bit permits full-gage long holes to be drilled by percussion drills at a lower cost than diamonds. The change in the use of percussion drills is chiefly in the method of mounting. The column and arm are disappearing and the jackleg and rubber-tired or track-layer jumbo mountings are taking its place. At the Homestake mine .lightweight jackhammers mounted• on pneumatic legs using 7/8-in. hexagonal drill. rods and 1 1/2-in, tungsten-carbide detachable bits have been found more portable and maneuverable. They have less air consumption, lowered, dynamite consumption, and more footage and tonnage per man-shift than with 3 1/2-in. drifters on a column mounting. Drills now are mounted on longer feed carriages, drilling up to 20 ft without changing steel. These mountings result in great savings because the driller can set up quickly, drill the entire depth of the hole without changing the drill rod or bit using carbide and one-use bits, and can move his machine quickly to the next hole. One man to the machine is becoming general practice. The result is longer rounds rounds drilled at a lower cost than the previously used short rounds. A jumbo developed in the Tri-State can be extended to mine ore left in the roof up to 65 ft above the floor. Drill-rod life was formerly considered to be about 250 min of actual use. The increase in the drilling time per rod per day has gone up considerably with the development of the jumbo and the long-feed carriage, resulting in which is apparently more rod breakage., Consequently, a great deal of research is being done in the attempt to develop an alloy-steel rod with longer service life to offset the greater cost. Some reports indicate that alloy steel or Swedish steel results in cheaper drilling than conventional drill rod. However, several tests have shown only slightly increased life for alloy drill rod. Undoubtedly, the blow of the rock drill, the length of the drill rod, and the resiliency of the rock being drilled are important factors in the life of drill rod, so it follows that alloy steel might work well in some mines and result in no savings in others. The bit forged on the drill rod is seldom encountered and steel detachable bits are not as common as in the recent past. The one-use bit is gaining popularity because of. the difficulty in rehardening reconditioned steel bits satisfactorily. It is thought that the, carbie-insert bit is most applicable to drilling hard 'rock' where the steel bit is unable to drill out a full change, for instance, in extremely abrasive

Jan 1, 1952

Jan 1, 1967

By Tokio Yanagida

Major parameters relating to the operating of the conventional calcine-charged reverberatory f'ce process such as distribution coefficients of major elements among slag, matte, blister, and gases, temperatures and weights of intermediates, and heat losses of furnaces were measured and determined. A computer program to estimate heat and material balances at the process was prepared utilizing these data, showing a good agreement with actual results.

Jan 1, 1984

By Robert B. Paul

This paper describes the new lead smelter and refinery recently completed by the American Smelting and Refining company in Southeast Missouri.

Jan 1, 1970

By E. S. Bumps, M. Baeyert, W. F. Craig

SOME time ago during a study of impact properties of tempered martensite,1 it was postulated that the consistently good ductility of tempered martensite might be caused by its relatively small and peculiarly shaped ferrite grains. The fer-rite grains of tempered martensite have approximately the same size and shape as the martensite "needles." Thus they form an interlocking mass of needle-shaped grains quite different from equiaxed or lamellar ferrite grain structures. When the common mechanical test methods are applied to steel, variations are often observed in the ductility of specimens that have closely similar hardness and tensile strength values. The ductility so measured appears to be structure dependent. When steel from the same heat has been heat treated to produce different structures with the same hardness, the elongation and reduction of area values from the tensile test and the transition temperature determined by the notched-bar impact test vary according to whether pearlite, tempered martensite, or other structural constituents were produced by the heat treatment. It has been widely recognized that tempered martensite gives a consistently good performance, when tempered to the same hardness as many other structures with which it has been compared. In recent years the isothermal transformation of austenite to specific structural products and the quantitative evaluation of the character of these products with respect to their nature and response to deformation has received considerable attention. The objective of the present study was to pursue somewhat further the dependence of ductility upon structure; specifically, it was desired to ascertain whether ferrite grain structure, including both shape and size of the grains, can account for the consistently good performance of tempered martensite in the notched-bar impact test. It was thought that a simple experiment would indicate whether the ferrite grain structure plays any part in the good ductility exhibited by tempered martensite in contrast to other steel structures with different types of ferrite grains. By determining the impact transition temperature, it was proposed to compare spheroidites having similar carbide particle size and spacing but obtained in such a manner that their ferrite grain structures would be very different. Spheroidite obtained by tempering martensite, with its small, needle-shaped grains, was to be compared with spheroidite from pearlite. If the latter is produced by sub-critical annealing, the ferrite grains correspond to the pearlite colonies. Thus, if the pearlite was not too coarse, the ferrite grains of spheroidite from pearlite are equiaxed in contrast to the needle-shaped grains of spheroidite from martensite. It was thought that the ferrite grain structure of spheroidite from martensite might depend to some extent upon the grain size of the prior austenite. The austenite grain boundaries limit the maximum attainable size of the martensite needles and thus of the ferrite grains in the derived spheroidite. In order to evaluate any possible influence of prior austehite grain size, spheroidites were to be prepared from martensites that had been formed from fine-grain austenite and also from coarsened austenite. As the carbide particle size and distribution were to be essentially alike in the various spheroidites, the difference would be in the ferrite grain size and shape. Thus any marked difference in transition temperature could be attributable to the character of the ferrite grain structure. There are certain considerations in assuming that these spheroidites would be equivalent in all respects except ferrite grain structure, and an attempt was made to take them into account. One of the considerations was the choice of the carbon content of the steel. An approximately eutectoid steel was selected for two reasons. First, the pearlitic structure would contain no proeutectoid ferrite which might complicate the picture by producing a non-uniform ferrite grain structure in the resulting spheroidite. Then, too, the high-carbon content would inhibit ferrite grain growth during the sub-critical treatment. Another factor to be taken into account was the choice of an alloying element to assure a martensitic structure throughout on quenching the impact specimens. Nickel was chosen, because it is a common alloying element and resides in the ferrite both upon its formation from austenite and throughout tempering. The formation of alloy carbides, or even a large solubility of the alloying element in cementite, would have complicated the interpretation by changing the composition of the ferrite .during spheroid-ization. The possibility of temper brittleness was minimized insofar as possible by using a tempering temperature as high as consistent with the 1 pct of nickel in the steel, namely, 1150°F. While it certainly is not claimed that no difference other than ferrite grain structure could exist between the spheroidites, nevertheless, reasonable precaution has been exercised within the limits of steel metallurgy. It is believed that any large difference in transition temperatures would reflect the difference in ferrite grain structure and that relatively good ductility in the spheroidites from mar-

Jan 1, 1951

By Dwight L. Sawyer

IF it had not been for the testimony of former Secretary of the Interior, Harold L. Ickes, before the Senatorial investigating committee the public would have heard little about the Federal Government's suit against California for the ownership of the tidelands. The Ickes-Pauley dispute brought to public attention that the California tideland oil deposits are the last remaining large Federal oil reserves. Ickes contends that these tideland oil deposits belong to the nation for the benefit of all the people of all the states and not solely to the State of California. Ickes also accused California oil man Ed Pauley of offering to give $330; 000 to the Democratic party fund if Ickes would drop the Federal Government's suit against the State of California for the ownership of said tidelands. The tidelands may be considered as the land bordering the coast line between mean high tide and outward under the ocean for a distance of a marine league, or about three statute miles. This strip of land along the coast of southern California contains large oil deposits which have a present and future prospective value of several billion dollars.

Jan 1, 1947