Search Documents

By R. H. Jacoby, V. J. Berry, R. C. Koeller

The experimental phase behavior of several field gas-condensate systems, one field volatile oil system, and a series of synthetic systems having gas-oil ratios from 2,000 to 20,000 scf/bbl stock tank oil was measured. The data were used to calculate the depletion performance of the field systems at their respective reservoir temperatures and of the synthetic systems at various temperatures. The results of the performance calculations were used to prepare correlations of total stock tank oil and separator gas in-place, and the amount of each recovered by primary depletion. Data needed to use the correlations are initial gas-oil ratio, initial tank oil gravity, reservoir temperature and reservoir pressure. The correlations presented should be useful for estiinating recovery from reservoirs producing volatile oils or rich gas condensates having gas-oil ratios from about 2,000 to 30,000 scf/bbl of stock tank oil. INTRODUCTION Prediction of depletion performance for gas-condensate reservoirs usually requires extensive laboratory work or lengthy phase-behavior calculations. For many small gas-condensate bearing zones the expense of such work is often not justified. Furthermore, where large holdings are involved, it is useful to have estimates of future oil and gas production in advance of the results of a laboratory analysis, even if such work is ultimately planned. For these reasons, it would be of value to have a method for rapidly estimating the depletion performance of gas-condensate reservoirs from the type of field data usually available. Few data on the reservoir depletion performance are available for the purpose of developing correlations. The increasing number of gas-condensate discoveries and the advent of high-speed computers have stimulated the development of methods for predicting performance. Such calculated performance data have been shown to be reliable and are becoming accepted as a basis for reserve estimates and for engineering studies. It therefore seems satisfactory to use results of performance predictions themselves for the purpose of developing the desired correlations. Such an approach is described in this paper. Several rich natural gas-condensate systems (gas-oil ratios of from about 3,600 to 60,000 scf/bbl) and one natural volatile oil system were studied (2,363 scf/bbl). In addition, to provide a more systematic basis for correlating purposes, a series of related, synthetic reservoir fluid mixtures was also studied (GOR's from about 2,000 to 25,000 scf/bbl). The purpose of this paper is to show how the recovery of oil and gas by primary depletion may be estimated from surface gas-oil ratio, reservoir temperature and pressure, and tank oil gravity. procedure Experiments Companion samples of gas and oil were collected from the high pressure separators in nine different fields at the time of their discovery. These samples were each recombined in accordance with the respective producing GOR to reproduce the reservoir fluids. Eight of these fluids, designated F-2 through F-9, were rich gas-condensate systems at the respective reser-

HAVING produced one ton of concentrate that contains the copper that can profitably be saved or recovered from anywhere between 3 and 60 tons of mine ore, the ore-dressing engineer passes the result of his handiwork over to the metallurgist for smelting. Essentially, the concentrate is a damp mass of finely ground material consisting of copper sulphide minerals; pyrite, the sulphide of iron; and gangue, usually silica and silicates of aluminum. The purpose of smelting is to produce metallic copper and a slag containing the iron and siliceous constituents by pyrometallurgy-the kind of metallurgy that employs fire and heat to produce the chemical reactions through which it attains its object. Though blast furnaces have been used to smelt Porphyry-mine concentrates, notably at Braden, more than 90 per cent of [ ]

Jan 1, 1933

By E. A. Holbrook

The art of ore dressing is as old as civilization itself. Jason's search for the golden fleece was perhaps only the use of sheepskins for catching gold from gold-bearing sands washed over them. From Hoover's translation of Agricola we gather that in the middle ages ore dressing had advanced through the stage of hand sorting to water concentration by jigging. German methods and apparatus continued in the lead until the closing years of the past century; indeed, it is little more than a generation ago that many ore-dressing plants in this country were designed and operated by German-trained ore-dressing specialists. Meanwhile the development of the ore deposits in this country during the nineteenth century brought forth new inventions and methods. Blake's invention of the rock breaker in 1858 and the coming of the Wilfley table about 1896 are random examples of the improvements caused by our expanding needs. Yet ore dressing remained an art developed and practiced more or less by cut and try methods. The publication of the volumes on Ore Dressing by Dr. Robert H. Richards in 1903 marks the beginning of American ore-dressing practice as a science. Previously we had as guides only a few incomplete books based on foreign practice, or scattered references and articles in our own Transactions. Dr. Richards set down all the developments that had gone before, and outlined the ways for a scientific approach to the subject. He gave us a starting point. Since then ore-dressing practice and technique in this country have set the pace for the world. Coal preparation has been called "ore dressing upside down,'' because in ore dressing we generally save a small percentage of the heavy valuable mineral and discard the lighter gangue, whereas in coal preparation we save the larger quantity of light mineral and discard the smaller percentage of heavy waste. By comparison with ore dressing the history of coal preparation is brief, extending backwards hardly 100 years, for although coal had been dug and used locally for centuries it became an important article of commerce only with the coming of the industrial revolution 150 years ago. In new mines it was to he expected that the thickest and purest seams should be worked first. So long as these lasted there was little thought of coal preparation other than hand picking of the larger impurities and simple sizing to supply the real or fancied need

Jan 1, 1934

By A. C. Fieldner

IN the Wall Street journal for March 1, 1941, was a tabulation of the construction under way or under negotiation by thirteen iron and steel companies for a predicted increase in annual coke production of 3,165,600 tons. That even this figure was short of the mark is indicated by other plans, then being considered, for a later expansion of 2,610,000 tons additional. Considerable progress has already been made on thin program, for approximately 500 new ovens were put in operation in 1941. and well over 200 should be completed in 1942. These figures include a number of units that replace older and obsolete equipment.

Jan 1, 1942

America.-Foreman, J. T. Ashland.-Sturdevant, J. C. AItalIa. Henderson, R. M. Bessemer.-Ball, E. M. Maschmeyer, W. L. McKenzie, W. C., Jr. Birmingham.-Abbott, C. E. Aldrich, T. H. Aldrich, T. H., Jr Aufderhaar, H. C. Berg, H. A. Blair, C. S. Bush, M. W. Clark, G. H.

Jan 1, 1923

By T. S. Fuller

Various phases of the embrittlement of solid copper containing oxygen by the action of reducing gases at high temperatures are familiar to readers of metallurgical literature through the work of many experimenters. In 1900, Heynl recorded observations of copper being heated in hydrogen with the development of fine cracks, the result of the formation of steam within the metal through the action of hydrogen on the copper oxide usually found in copper. Archbutt,2 in 1905, published the results of experiments, showing that all oxygen can be removed from copper by heating to redness, for several hours, in hydrogen. Intercrystalline cracks and extreme brittle-ness developed. Archbutt attributed the brittleness to the reduction of oxides present in the copper. Bengough and Hil1,3 in 1910, encountered the now well-known embrittlement at the outset of their investigation and stated in their paper: It soon became evident that the effect of any heat treatment depended largely on the presence or absence of reducing gases in the atmosphere of the furnace, as well as on its temperature. Hence it became necessary to adopt a somewhat elaborate scheme of heat treatment. The authors found embrittlement in separate experiments due to both hydrogen and carbon monoxide and concluded that: "The gases ruin the alloys after being heated to about 650" C. in their presence." Ruder,4 in 1916, reported the results of a series of experiments made by heating commercial and deoxidized copper in hydrogen, carbon monoxide, carbon dioxide, and steam. In agreement with other writers, he found that copper containing oxygen was made brittle by reducing gases, while the deoxidized metal remained unaffected. In the case of

Jan 1, 1926

By H. O. Hofman

Jan 1, 1890

By W. J. Uren, Charles R. Kuzell

The industries engaged in winning minerals from the earth, because of their widespread dissemination, are faced with perhaps as wide a variety of labor-management problems as may be found in any other broad sphere of productive activity. Those problems are continually increasing in volume and complexity, and management has become aware of their growing importance. For the past quarter century at least, labor-management problems have largely been union-management problems. During this period tremendous assistance has been given labor unions through legislation and administrative and political action. In the United States, legislation favorable to unions has come about in the form of the now defunct National Industrial Recovery Act; the Wagner Act, most of which has been carried forward in the Taft-Hartley Act; the Norris-La Guardia Act; the Wage and Hour Law; the Walsh-Healey Act; and others. The result has been to transfer from the hands of management to those who direct the affairs of the unions a large share of control over the industry and to hamper in many ways the remaining control left to management. In the United States there are many examples of the power of unions to injure whole industries seriously with- out regard to the interests of management, the employes, or the public. This chapter deals with the various phases of labor-management relations as they affect the principal segments of the mineral industry in North America. To the greatest extent possible available data is presented pertaining to the unions involved, their relative strengths, labor law, compensation and fringe benefits of employes, working conditions, and related matters. As background, the historical development of union-management relations in the respective segments is included where possible. The section dealing with the United States has been divided into separate

Jan 1, 1959

By R. E. Reed, C. J. McHargue

Single crystals of aluminurn were reduced 90 pct in diameter by extrusion at 296" and 77°K. The resultant double fiber texture had a strong (111) component with a weak (001) component. The relative anzounts of these components varied with starting orientation. Decreasing the Lemperatuve of defovtnation increased the amount of (001) texture component in crystals with inilia1 orientations near (111). The starting orientation and temperature of deformation strongly affected the morphology of the (001) component. The effects of orientation and Lemperatuve upon the distribution of the (001 ) texture component in extruded aluminum single crystals were rationalized on the basis of deformation band formation and interaction. MANY papers since the early 1920s have discussed the occurrence of the double fiber texture (111) + (001) in wires and rods of deformed fcc metals. Aside from the reporting of experimental results for the various metals under a variety of fabrication conditions, emphasis has been placed on two related problems. One problem deals with the prediction of ideal end orientations based on the glide systems and flow directions. The other problem seeks the reason why different amounts of each component may be produced by the same fabrication schedule for metals apparently having the same deformation systems. Some of the difficulties in developing a satisfactory explanation have their origin in the experiments themselves. One mistake has often been the assumption of an initially randomly oriented specimen or complete ignorance of effects of starting orientation. Recent studies by Grewen and Wassermann,1 Cullity and co-workers,2' and McHargue4 have shown that the initial orientation may be the most important factor in determining the final orientation. Hence only limited comparisons of data from different studies can be made unless all conditions of the initial material are specified. Another question has been the nature of the (001) component. Hibbards suggested that any (001) present was the result of re crystallization during fabrication. Although Fleischer6 found no (001) texture in aluminum swaged at room temperature, and Dayal 7 found that component to disappear at very high reductions, a double fiber texture has usually been reported for aluminum. Vandermeer and McHargue showed that, while some (001) in aluminum may be the result of recrystallization, much of this component has its origin in the deformation process. Ahlborn and Wassermanng found the (001) component in silver deformed at low temperature not to be the product of recrystallization.

Jan 1, 1968

By J. M. Dahl, R. J. Warrick, O. K. Riegger, H. Van Vlack

A liquid which is rich in oxygen (and silicon) develops at steel rolling temperatures in resulfurized and plain-carbon steels. This liquid fluxes solid manganese sulfide. The composition of the liquid and the resulting microstructures vary with the manganese/silicon/oxygen ratios in the steel. The observations and conclusions zuhich are presented are used 1) to suggest a mechanism for MnS deformation in resulfurized steels, and 2) to rationulize hot-shortness anomalies between plain-carbon and resulfurized steels. 1 HIS is a summary of the dependence of sulfide inclusion microstructures upon steel composition, and an interpretation of the behavior of sulfide inclusions at steel-rolling temperatures. Sulfide inclusions are known to have several metallurgical effects upon steel. Their effects upon hot-shortness are best appreciated. Although hot-shortness is well known, it is questionable whether its mechanism is fully understood because there are several anomalies in our interpretation. For example, why should not high sulfur contents produce extensive hot-shortness in free-machining steels ? A second metallurgical consequence of sulfide inclusions appears because sulfide inclusions improve machinability. Furthermore, globular inclu- sions are to be desired over elongated inclusions. To date, we know that lower silicon contents (< 0.010 pct) favor the globular sulfides, but we do not know why this interrelationship between silicon content and inclusion shape exists. Finally, the evidence is strong that the surface quality of a hot-rolled steel is particularly sensitive to the sulfur content. SUMMARY OF PREVIOUS WORK The role of sulfur in hot-shortness was first suggested during the past century. It is uncertain who was the first to conclude that sulfur was less deleterious in the presence of manganese, and that manganese altered the sulfide phase from a liquid FeS to a solid MnS at steel-rolling temperatures. However, Urban and chipman&apos; emphasized that liquid FeS may accumulate as an interdendritic film during solidification. More recently, Keh and Van lack&apos; showed that the intergranular liquid does not completely surround the metal grains at all rolling temperatures. Rather, a small finite dihedral angle exists when geometric equilibration is attained at

Jan 1, 1962

By H. [Eyring], B. J. Zwolinski

[ ] The authors are to be commended for their excellent work on the activities of components in the solid state. It is, however, felt that certain points require clarification with reference to diffusion in the solid state. It is a well established point that any rate process in a non-ideal system can be expressed by the general equation [ ] where ko is the specific rate in an ideal system, and ?A, ?B ... , the activity coefficients of the reactants and ?± and ?M,?N the activity coefficient of the activated complex and the intermediates, respectively. With reference to diffusion, the following simplified treatment in correcting for non-ideality is proposed. The same free energy change is involved in moving a particle from a solution of one activity to a solution of another activity,

Jan 1, 1947

By D. D. Dunkin

Sandstone has been prepared for glassmaking purposes, and marketed from the White River Valley in Arkansas at Guion, Izard County, since about 1910—soon after the completion of the White River Branch of the Missouri Pacific R. R. Co. Until 1921, operations were somewhat spasmodic and ended in many failures. In that year a plant was built by the Silica Products Co., Inc., and since that time the operation has been continuous and steady. The land is held under leases, covering about 30 square miles of the best sandstone adjacent to the railroad. Most of the product is shipped to glassmakers. Geology The St. Peter sandstone is rather widely distributed in north central Arkansas and is exposed most prominently in outcrops along the slopes of the White River Valley and its tributarirs that form the division between the Boston Mountains to the south and the Salem Plateau of the Ozarks to the north. It is of Ordovician age and is generally underlaid by Cotter dolomite and capped by Plattin limestone, except in the vicinity of Bellefonte and Everton. At those places, it is a massive cross-bedded, laminated, saccharoidal sandstone; underlying it is the Everton limestone and overlying it, the Joachim magnesium limestone The sandstone at Everton contains numerous phosphatic pebbles and inclusions of sandy limestone. The irregularity of cross-section, the evidence of sorting action and the phosphatic pebbles appear to be indications of secondary deposition The St. Peter sandstone occurs as a massive formation in the picturesque bluffs along the White River Valley from near the eastern escarprnent of the uplift northwestmard into the Ozarks. The exposure shows a series of gentle anticlinal and synclinal folds. The greatest thickness is at the southeastern end, where it is over 100 ft. in many places. It thins out to the north and west and then to isolated and scattered deposits which cap the ridges and mountains of the Ozarks.

Jan 1, 1928

By Walter B. Lenhart

Introduction and Importance of the Industry Sand, as described in this chapter, is a crude product used for ballast on railroads and highways, and as the fine aggregate in concrete, mortar, plaster and in asphalt paving materials. The sand used in glass, as a molding sand, and as a source of silica is described in Chapter 43. Sand and gravel together constitute the mineral raw materials of largest volume produced from the earth. In 1958, as reported by the U.S. Bureau of Mines,21 680,080,000 tons of sand and gravel (including industrial sand) were produced in the United States. The nearest competitor was crushed rock of which 532,818,000 tons were produced. Coal, both bituminous and anthracite accounted for only 431,616,689 tons in the same year. In dollar value, sand and gravel were exceeded only by cement, crushed rock and fuels. Hence it is a major unit of the mineral-producing industry. As an example, one plant in California operates around the clock at an average rate of 1,500 tons per hour, and at peak intervals has shipped over 4,000 tons per hour, all by trucks. Nevertheless, it is controlled by one man through a panel of push buttons that control the crushing, screening, washing, grading, stock piling, and reclaiming of the products. Because sand and gravel are low-valued commodities, but are used in every construction undertaking in every city, village, farm, dam and highway, they are produced in almost every county in the United States and southern Canada, by thousands of individual operators, very few of whom operate in more than one community. Many operations, particularly those established to supply the needs of major dams that are under construction, or of major segments of new highways, are temporary in nature, and the equipment installed is more or less portable. Because of the bulky nature of sand and gravel, there is very little interstate movement, and almost no exports or imports, except a little movement back and forth across the border of the United States and Canada. First, the material needs definition. Definitions Sand and gravel have been defined as continuously graded unconsolidated materials that appear in the earth&apos;s surface as a result of the natural disintegration of rocks. Both normally appear together, but in a wide variety of sizes, types and range of size classification. The American Society for Testing Materials has tentatively revised its definition of "sand" as: granular material passing the 3/8-in. sieve and almost entirely passing the No. 4 (4760-micron) sieve and predominantly retained on the No. 200 (74-micron) sieve, and resulting from natural disintegration and abrasion of rock or processing of completely friable sandstone (ASTM Designation C 58-55T). The Society&apos;s tentative revision of its definition of "gravel" is: granular material predominantly retained on the No. 4 (4760-micron) sieve and resulting from natural disintegration and abrasion of rock or processing of weakly bound conglomerate (ASTM 125-55T). Sand and gravel deposits contain materials from the finest silt to the largest boulders. Chemical definition of the two materials is nearly impossible. Sand and gravel always are

Jan 1, 1960

By M. E. Wadsworth, R. L. Pearson

THE dissolution of UO, in carbonate solutions can occur only il the tetravalent uranium is oxidized to the hexavalent state. The carbonate system is of particular interest because it provides a means whereby the oxidized uranium may be dissolved by forming the complex ion UO,(CO3)3-1. In the presence of oxygen the over-all reaction may be written UO+1/2O,4CO3T+2HCO2UO,(CO4)11+H2O [1] UO, was used in this study because it could be obtained in high purity and also because it is representative of the most refractory of the primary uranium minerals. The mineral ulrichite is the natural counterpart of the synthetic UO, used. The kinetics of the leaching of UO, should be similar for any of the uraninite type minerals. A pressurized system was used not with the hope it could be extended to commercial systems as a primary purpose but simply to provide the means whereby important temperature and pressure parameters could be varied for the evaluation of the kinetic processes. The importance of such pres-

Jan 1, 1959

By P. D. Gorsuch, D. L. Newhouse, Irvin R. Kramer

ALTHOUGH many methods have been suggested for the calculation of tensile strength and yield point from chemical composition, their usefulness has been limited to a particular cooling rate or section size. Further limitations have been imposed by failure to take into account many of the alloying elements that exert a considerable influence on the tensile strength or yield point. These systems, nevertheless, have filled an important need in many instances. The value of a system for the calculation of the tensile properties from the chemical composition and cooling rate is that it permits the prediction of the effect of alloying elements and heat-treatment on the mechanical, properties, so that more efficient use of alloying elements may be made. Furthermore, it aids in the choice of steel for a given application and tends to decrease the number of steels that otherwise would have to be tested. It is the purpose of this work to present a method of calculating tensile strength and yield point from the chemical composition and to suggest a method of correlating the tensile-strength and yield-point factors and cooling rate. Steelmakers have been interested for many years in the calculation of the tensile strength of hot-rolled steels. Quest and Washburn&apos; summarize several of the attempts that have been made to devise formulas. They show the inadequacy of each of these formulas and present one of their own. It is apparent from their work that a simple additive equation of the type TS = A + BX + Cy + DZ + ? ? ? , where A, B, C, D, etc. are experimentally determined constants and x, y, z, etc., are the percentages of alloying elements present in the steel, is not adequate to analyze fully the situation encountered in the calculation of tensile strength. For example, it was found that the difference between the calculated and observed values became progressively greater as the carbon and manganese contents were increased. Therefore, the effect of manganese was given as a function of the carbon content. Grossmann,2 in his work on the hardenability of quenched steels, and Walters,3 in his method of calculation of tensile strength of normalized steels, present two cases in which multiplying factors were successfully used to express the combined effect of alloying elements. The factors in both cases were obtained from the fractional increase in hardenability or tensile strength with increase of alloy content. Yield point often is more important in design than tensile strength. For quenched and tempered steels a linear correlation exists between yield and tensile strength .4 This is not true, however, for normalized

Jan 1, 1946

By G. S. Cole, G. F. Bolling

Fluid flow strongly influences ingl structure and the columnar -to-equaaxed transition. Artificial flow patterns siwzilar to the nuturul ones act to induce this transition, while dampening forces act to suppress this transition. It is shown here how simple mechanical forces can be applied to a systerrz in order to induce or slipPvess relative fluid flow and the change both the structure transition and the exact structures obtained. The example used is the effect of slow rotations and oscillations 012 a cooling- ingot (of laboratory scale). The details of rotution and oscillation for various cooling rates, lenlperal~ire gradients, and sizes of ingot are related to other solidzfication variables. THE grain structure of a casting can be changed by altering the fluid motion during solidification. Just how important these changes are depends directly upon the degree to which the fluid motion can be controlled. An early step in understanding the nature and influences of fluid motion was taken by studying natural thermal convection; when a static mechanical device was used to suppress natural flow the result was opposite to that obtained when an electromagnetic device was used to augnlent flow in a pattern similar to the natural one. &apos;&apos;2 Suppression allowed more columnar growth to occur, but "augmented natural convection" brought about an earlier columnar-to-equiaxed transition (CET). Since the solidification of a free ingot must have characteristics somewhere between those displayed during suppression and augmentation, we know that natural convection must influence the CET. Further, since heat transfer in the liquid is always some time-dependent combination of convection and conduction, it can easily be guessed that the temperature gradient in the liquid is the vital factor affecting the CET.1,2 It is obvious that the structure arising from the unadulterated solidification of an ingot, without external influence, is rarely if ever the best possible one. Although the pattern of the natural fluid flow may be considered efficient, the magnitude of the flow and the heat transfer decrease freely from the outset. For a

Jan 1, 1968

By Theodore Simons

(Butte Meeting, August, 1913.) DURING the last half century a great amount of ingenuity and energy has been devoted to the invention of appliances for the recovery of valuable minerals from very fine sands and slimes. The reason for this is that in almost every dressing plant the greatest losses of values, considered relatively as well as absolutely, occur in the treatment of slimes. The natural aim of mill operators to minimize these losses has in recent years received another impetus, from the fact that the gradually diminishing occurrence of high-grade ores makes a more intense recovery of values from existing resources absolutely necessary for profitable operation. The results of such attempts are found in the appearance of a great number of machines and appliances which make it profitable to-clay to rework old dumps, containing the tailings of older processes. A constantly growing difficulty of obtaining skilled labor and the increase in wages made it prohibitory to employ those types of machines which required much attention, and in the middle of the nineteenth century the various concentrating tables of the percussion type, which automatically discharge their products, began to take the place of the intermittent tables, on which, when the bed had reached a certain thickness, operation had to be stopped in order to allow the skimming by hand of the separate layers formed on the table. In the course of years, two general types of machines evolved for the treatment of fine sands and slimes : The so-called concentrators and vanners, on the one hand, and the buddies and round tables on the other.1 For the profitable treatment of the very finest slimes, round tables have as a last resort proved more satisfactory and economical than other machines.

Jan 7, 1913

By H. S. McKnight

One phase of Canada&apos;s rapid development in mining and metallurgy during the past few years has been the creation of Canadian Copper Refiners Ltd., and the establishment of its modern electrolytic copper refinery at Montreal East, Quebec. Canadian Copper Refiners Ltd. is made up of three well-known metal firms whose combined activities cover the entire industry from the mine to the market. They are Noranda Mines Ltd., Toronto, Nichols Copper Co., New York, and British Metal Corporation, Ltd., London. Noranda Mines is the principal owner and provides the greater part of the raw material received by the refinery for treatment. Nichols Copper Co. designed and built the plant and is operating it under contract. British Metal Corporation acts as sales agent and markets the refinery&apos;s products. Montreal East was chosen as the site of the new refinery only after a careful survey had been made of the entire eastern part of Canada. The location chosen offers many advantages, chief of which arc the relatively low costs of power, labor, fuel and bupplies, and the fact that it is situated on Montreal harbor, the nearest seaport to the points of origin of the ram materials. All incoming material is received by rail. A majority of the plant&apos;s product is exported through the port of Montreal to European markets, being handled to the docks in railroad cars. A large proportion of the product is delivered by means of an industrial railway to the adjacent rolling mill of the Canada Wire & Cable Co., Limited. The refinery was designed to treat primarily the copper produced by Noranda Mines, Ltd. and Hudson Bay Mining &. Smelting Co., Ltd., and its rated capacity is 75,000 short tons per year. A general layout of the plant is shown in Fig. 1. Its capacity can be readily doubled, as shown by the dotted lines. Figs. 2 and 3 are sections taken through the furnace department and the tank house respectively. Except for the main office and laboratory and an auxiliary building containing the stores, warehouse, change rooms, compressor room and machine shop, the entire plant is under one roof. The type of building construction consists of reinforced concrete foundations supported on concrete piles, a steel structure covered with Robertson Protected Metal siding and a 3-in.

Jan 1, 1934

By T. A. Rickard

From time immemorial the fissure-vein has been held the simplest type of ore-deposit. The prominence given to it by Cotta and his disciples, from their study of the mines of the Erzgebirge, is impressed upon technical literature; and, in consequence, the ores which carry the valuable metals have been supposed to occur mainly in fissures, cleaving the rocks in diverse directions, and the noblest type of vein has been deemed that which cut across the country independent of its structure, whether evidenced as bedding, foliation or cleavage, and which was identified with rents produced in the rocky crust of the earth. As so conceived, the vein was a fissure filled with ore, extending through the country for a varying distance, and continued downward to a depth more or less proportionate to its longitudinal extent. The vein-material was bounded by an encasement of rock, and those immediate surfaces which limited it on either aide were called " walls." These primary conceptions have become modified by the experience of modern mining in widely separated regions. The study of lode-formations has led to the recognition of notable departures from the supposed normal structure of the veins of Saxony and Cornwall, the two classic homes of early economic geology. Typically the walls of a vein are conceived as parallel rockplanes enclosing the ore; the upper one being called the " hanging-," and the lower the "foot-wall."* Walls are rarely alike. Even where a vein traverses a homogeneons formation, such as a massive crystalline rock, it is usually found that the surface which bounds it underneath

Jan 1, 1897

By B. B. A. Luzzat

ALUMINUM is today the most widely used of the nonferrous metals. The technical literature on the aluminum smelting process is, nevertheless, very meager, so that anyone interested in the subject cannot rely on more than a couple of dozen publications.&apos; The patent literature is equally scarce; most patents refer to the production of alumina from aluminum-bearing ores, while not more than a few score significant patents deal with the electrolytic reduction of alumina, which is the real core of the aluminum smelting industry. The "reduction phase" is, from a technical and a scientific point of view, much more interesting than the "alumina phase", which, in effect, is only a combination of such well-known chemical operations as dissolving, precipitating, filtering, drying, and calcining. The electrolytic reduction of alumina, on the other hand, has features which do not appear in any other metal smelting operation. Some of them are of great technical and scientific interest even for those not directly engaged in the production of aluminum. The purpose of this paper is to describe in some detail the basic facts and developments of the reduction phase of aluminum smelting. Two Aspects of the Electrolytic Process The raw material for the reduction process is alumina (Al2O3) . Its purity in general runs as high as 99.50 pct or more. Small differences in the chemical composition generally do not affect the reduction process.* Of more importance are the physical prop- erties of the alumina, since they affect not only its rate of solution in the molten bath but also its heat insulating power.† In the following pages, un- less otherwise stated, it is assumed that a standard "Bayer" alumina is used. The reduction process, by which alumina is broken down into its components, may be roughly defined as its electrolysis in molten cryolite. The oxygen separates at the anode, and the aluminum at the cathode, which forms the bottom of the electrolytic cell. The electrolytic cell (or pot) where the process is carried out is a strongly reinforced steel box. The

Jan 1, 1951