Search Documents

By Arthur G. Levy, Henry M. Howe

$1. Introduction.—Any given piece of metal is made up of a very great number of grains, usually microscopic, each of which is a perfect crystal save only in outward form, with cleavage planes of low cohesion, geometrically arranged quite as in fie familiar non-metallic crystals. The plastic deformation of such a mass occurs chiefly through the slipping of the crystalline blocks of which each grain is composed along these cleavage planes, causing steps called slip bands to form on a previously polished surface. In this slip, the metal immediately adjoining each of the cleavage planes along which the slip takes place is thought to pass extremely rapidly through a very mobile state into the amorphous state, in which it is harder than the remaining still crystalline metal between the amorphous layers thus formed along the slip planes. Whether the slip planes below the surface in ferrite can be detected by cutting, polishing, and etching sections is in dispute; but if this detection is possible at all, it is usually made impossible by heating the metal even gently. In short, the change along the slip planes does not persist through heating, and it is thought not to persist through time even at the room temperature, nearly all the amorphous metal recrystallizing. The network in Fig. 22 and the parallel N.-70-E. lines in Fig. 21 are slip bands in copper. When plastically deformed metal is heated, certain parts of certain grains may twin, that is, their component crystalline units may rotate into a position, or more exactly into an orientation, symmetrical with the initial orientation and hence with that of the remainder of that grain. As seen in a microsection of a metal the twinned areas usually have parallel sides. The existence of twinning is recognized in metallic sections either by the presence of such parallel-sided areas differing in brightness from the adjoining metal, especially when seen under oblique light after etching, or more surely by the zigzagging of the slip bands which form when twinned metal is itself deformed again. Hence the usual procedure in developing twins is to deform plastically so as to cause the twinning tendency; to heat so as to allow the tendency to assert

Jan 1, 1915

By D. T. Novick, M. B. Bever, B. Roessler

Ordered and disordered specimens of the alloy CusAu were cold worked and then annealed at 2880, 310°, and 340°C, together with disordered unworked specimens. me resistivity decreased during annealing mainly as a result of ordering; the resistivity measurements suggest that in cold-worked specimens the growth of antiphase domains is impeded. The strength properties increased during annealing at 288 "C; in cold-worked specimens this increase was lo a level above that for cold-worked specimens which had not been annealed. X-ray diffraction showed that after annealing for a few hours at 288ºC, the long-range order increased to a constant value; additional annealing at 288ºC resulted in the growth of antiphase domains in which the degree of order was constant. Changes in peak breadth and particle size confirmed that in cold-worked specimens the major effects of cold work were not eliminated during annealing at 288 "C, although a slight recovery process occurred. When a specimen of the alloy Cu3Au is heated to a temperature below the critical temperature (388ºC), long-range ordering tends to occur in a specimen containing less than the equilibrium amount of order characteristic of that temperature Ideally, a specimen of Cu3Au contains no long-range order if it has been quenched from above the critical temperature. Long-range order is reduced by cold work. If cold-worked specimens are heated, restoration processes such as recovery and recrystallization may occur,

Jan 1, 1963

By Arthur Dwight

ARTHUR SMITH DWIGHT, president of the American Institute of Mining and Metallurgical Engineers, was born in Taunton, Mass., on March 18, 1864. He is descended on both sides from early settlers, one of whom was Richard Warren, of the "Mayflower." His forebears included Col. Benjamin Church, Tim-othy Dwight, and the Rev. Jonathan Edwards, third president of Princeton College. Mr. Dwight was graduated in 1882 from the Poly-technic Institute of Brooklyn, N. Y., and three years later from the Columbia School of Mines, with the degree of Engineer of Mines. In 1914, he received the honorary degree of Master of Science from Columbia. On leaving Columbia in 1885, he went to Pueblo, Col., and for thirteen years was associated with the Colorado Smelting Co. Beginning as assayer he rose to be general superintendent. When he gave up the latter position he became connected with several large companies in the mining and smelting of lead, copper and the precious metals in the Rocky Mountain region. This work occupied him from 1897 to 1906, and six years of that time were spent in Mexico. He was general manager of the Greene Consolidated Copper Company at Cananea, Mexico, in 1906, when trouble first developed against the régime of Diaz. A general uprising was planned to seize the mines, and with money and supplies so obtained, carry the revolt through the interior. Mr. Dwight turned his industrial organiza-tion into a military unit almost over night, stemmed the tide of revolution, and had the situation well in hand before the arrival of troops. In the fall of 1906 he returned to New York and began practice as a consulting mining and metallurgical engineer. He next developed important metallurgical patents for the roasting and agglomeration of fine ores, known as the Dwight and Lloyd sintering process, now extensively used ail over the world.

Jan 3, 1922

By Henry Tobelmann

THE location, mode of occurrence of ore, and preliminary tests leading to the development of the present leaching process and the building of the present plant on the property of the New Cornelia Copper Co. at Ajo, have been described in previous papers presented to the Institute and in the, discussions thereof.1 It is sufficient to say that these tests began early in July, 1912, and were continued to the close of January, 1916; that small tests at Douglas were followed by the construction of a 1-ton plant at the mine; and this was followed by the operation of a 40-ton plant for 14 mo. In all about 15,000 T. of ore were treated experiment-.

Jan 2, 1919

By Manuel Eissler

The material presented in this paper is an abstract of a thesis submitted by the writer to the faculty of the Massachusetts Institute of Technology, as part requirement for the degree of Master of Science. The investigation was undertaken at the suggestion of Prof. H. 0. Hofman, and it was conducted, under his direction, in the laboratories of the Mining Department of the Institute. The purpose of the work was, first, to study some of the reactions that have been considered as a part of the mechanism of the chloridiz-ing roast, and second, to study the conditions under which nickel oxide and copper oxide may be chloridized. While the production of chlorine gas by various reactions during the chloridizing roast may not be primarily useful in the chloridation of metal oxides and compounds, it nevertheless serves a useful purpose in preventing the dissociation and decomposition of chlorides once they have been formed; for example, the dissociation of cupric chloride into cuprous chloride and chlorine. Therefore it was thought that a study of some chlorine-producing reactions would prove of interest, and the first series of experiments dealt with this phase of the subject. he object of the latter part of the work was to show the possibility of treating heavy sulphide ores, such as those of Sudbury, Ontario, containing much iron and small amounts of copper and nickel, by chloridizing and removing the copper, leaving an iron-nickel oxide product suitable for smelting in the blast furnace for nickel-bearing pig iron. The chloridizing of the copper would, of course, be preceded by a roast for the removal of sulphur, the sulphur oxides being available for the manufacture of sulphuric acid, if under the local conditions this product would be of commercial value. Reactions of the Chloridizing Roast Reaction of Sodium Chloride, Sulphur Trioxide, and Oxygen.—The first reaction studied was that involving the production of chlorine

Jan 1, 1915

As 1970 develops and industrial minerals stand at a crucial point in their progress, research and development programs appear to be the key needed to open up new uses for each mineral's future growth. Radically new processes are needed for making a host of new synthetic products from mineral raw materials which will more nearly meet the demanding specifications required for high performance in space, nuclear and defense applications. Consumer applications for high temperature environments will be needed and are important for continuing the nations economic mineral position. In addition, an acute materials problem limits the effectiveness of some of the newer concepts for controlling ail pollution. What is needed then, according to a report printed by the National Academy of Sciences, is the carefully planned development of a limited number of major centers at universities to provide for both basic research and training of personnel; the nurturing of interdisciplinary mechanisms for research and problem solving within these centers; the achieving of a better balance between physics and chemistry within research, emphasizing the chemical aspects of the material sciences; and the enhancement of a broader professional identity by unifying the various disciplines involved into a possible federation of existing societies which have an interest in the problems. [EE] presents its 1969 annual industrial minerals review, where individual authors evaluate the status of each industrial mineral and recount the major developments which occurred during the year.

Jan 1, 1970

By Edmund S. Davenport

The production of thorium of high purity by the Ca-CaCl2 reduction has been described by Marden and Rentschler,1 who also reported some of the properties of the coherent, ductile metal obtained from this pure thorium powder. The present paper describes the properties of thorium produced by the Ca-CaCl2 process modified in some details to meet commercial conditions. The principal effect of these changes in process has been an unavoidable increase in the oxide content of the thorium. Materials and Methods The thorium employed in this investigation was made from pure thorium oxide (ThO2) by the Ca-CaCl2 reduction. The washed and dried metal powder was pressed into bars approximately 0.160 in. dia. and 10 in. long, at a pressure of 75,000 Ib. per sq. in. The bars were heat-treated in vacuum at 1175' C. for 1 hr. This treatment yielded ingots sufficiently dense and coherent for mechanical working. Thorium has been successfully worked without a protective metallic covering, but for the purposes of this investigation it was more convenient to inclose the ingots in soft iron tubes and swage or roll cold to the desired sizes. The iron sheath was dissolved with nitric acid, leaving the cold-worked thorium exposed. Chemical Analyses Analyses of typical samples of the material used in this work arc given in Table 1. Thorium powder oxidizes in moist air, even at room temperature; no unusual precautions were taken to prevent such oxidation of the material used in this investigation. A certain amount of oxidation probably takes place during pressing; certainly during heat-treating unless a very slow heating schedule is employed. These factors account

Jan 1, 1930

By H. J. Morel-Seytoux

The influence of patten, geometry on assisted oil recovery for a particular dispIacement mechanism is the object of investigation in this paper. The displacement is assumed to be of unit mobility ratio and piston-like. Fluids are assumed incompressible and gravity and capillary effects are neglected. With these assumptions it is possible to calculate by analytical methods the quantities of interest to the reservoir engineer for a great variety of patterns. Specifically, this paper presents (1) very brieily, the methods and mathematical derivations required to obtain the results of engineering concern, and (2) typical results in the dorm of graphs or formulae that can be used readily without prior study of the methods. Results of this work provide checks for solutions obtained from programmed numerical techniques. They also reveal the effect of pattern geometry and, even though the assumptions of piston- like displacement and of unit mobility ratio are restrictive, they can nevertheless be used for rather crude but quick, cheap estimates. ,These estimates can be refined to account for non-unit mobility ratio and two-phase flow by correlating analytical results in the case M = 1 and the numerical results for non-piston, non-unit mobility ratio displacements. In an earlier paper1 it was also shown that from the knowledge of closed form solutions for unit mobility ratio, quantities called "scale factors" could be readily calculated, increasing considerably the flexibility of the numerical techniques. Many new closed farm solutions are given in this paper. INTRODUCTION BACKGROUND Pattern geometry is a major factor in making water-fIood recovery predictions. For this reason many numerical schemes have been devised to predict oil recovery in either regular patterns or arbitrary configurations. The numerical solutions, based on the method of finite difference approximation, are subject to errors often difficult to evaluate. An estimate of the error is possible by comparison with exact solutions. To provide a variety of checks on numerical solutions, a thorough study of the unit mobility ratio displacement process was undertaken. To calculate quantities of interest to the reservoir engineer (oil recovery, sweep efficiency, etc.), it is necessary to first know the pressure distribution in the pattern. Then analytical procedures are used to calculate, in order of increasing difficulty: injectivity, breakthrough areal sweep efficiency, normalized oil recovery and water-oil ratio as a function of normalized PV injected.

Jan 1, 1967

By Howard Scott

Manganese being perhaps the least expensive of the metallic alloying elements that can be advantageously added to iron in considerable quantities, the basic characteristics of its alloys with iron are properly receiving much attention at present. In the course of a dilatometric investigation of this system several years ago, the writer observed certain transformation phenomena not found in other iron-base alloys. The interpretation of those effects was not evident from the information then available, but recent X-ray studies clear up at least one anomaly and permit a more satisfactory description of the results than would have been possible otherwise. Aside from the new phenomena observed, the effect of manganese on the Arg transformation is of timely interest because of its bearing on the critical compositions of austenitic alloys, the applications of which are now being greatly extended. It is known that the properties of these alloys are unstable unless the As transformation occurs at a tem-pcrature considerably below atmospheric and that manganese is very effective in depressing the temperature of this transformation. The writer aims to establish a simple general relation which expresses the location of Ar3, quantitatively in terms of the content of the common alloying elements used in steel. A step in that direction is taken here. Early dilatometric investigations1 indicated that only one transformation other than the eutectoid A1 occurs in the high-iron alloys of the iron-manganese system. Dejean represents the Arg point as falling to 0" C. with a manganese content of 11 per cent and carbon content of between 0.30 and 0.40 per cent. Esser and Oberhoffer," sing alloys low in carbon (under 0.03 per cent), arrived by extrapolation at 14 per cent for the manganese content at which As is depressed to 0" C. Not until both low carbon contents and alloys having a manganese content

Jan 1, 1931

Impact Transition Temperatures of Some Pearlite-Free Mild Steels As Affected by Heat Treatments in the Alpha Range H. P. Tardif (Canadian Armament Research and Development Establishment, Quebec)—Mr. Josefsson is to be congratulated for his study of a most difficult subject and for the theories proposed to explain the re- sults. One point which, however, might not have received proper attention is that of the shape of the stress-strain curve at the yield point of quenched and furnace-cooled specimens and of specimens strain aged

Jan 1, 1956

By E. G. Banks

THIS paper is presented in the belief that metallurgists and chemists will be interested in the practice of grinding in tube-mills in connection with stamps, especially since the records of working here given extend over a lengthy period of time (since May, 1905). The ore from the Waihi mine-more especially that produced in the upper levels-contains a large proportion of hard, chalcedonic quartz, and the gold exists in an exceedingly fine state, conditions which necessitate very fine crushing in order to ob¬tain a high extraction of the precious metal. Before the introduction of tube-mills at the 90-stamp Waihi mill, it was found necessary to stamp through 40-mesh (1,600 holes per sq. in.) woven wire-screens, having a fairly high discharge. The pulp then graded

Jan 1, 1907

By John T. Wizzard, R. P. Killmeyer, B. S. Gottfried

The Coal Preparation Branch of the Pittsburgh Energy Technology Center has developed a computer program to calculate the performance characteristics of coal washing devices. This program uses specific gravity analyses of the clean coal and refuse streams as input, and generates dependent and independent performance criteria for the washer. Partition curves are internally represented in a functional form by a Weibull function. Performance criteria generated by this computer program are compared to manually calculated performance criteria for air tables, Dynawhirlpools, Baum jigs, hydrocyclones, and dense medium cyclones. The comparisons show that the computer program gives results in close agreement with the hand- calculated values while greatly reducing the amount of time involved in performing the analyses.

Jan 1, 1983

By AIME AIME

THE 1944 Chairman of the Institute of Metals Division might be classed as metallurgically ambidextrous ; he is teacher of theory and practice of both nonferrous and ferrous metallurgy, and he is consultant on brass and on highspred steel. Arthur Phillips was born in Troy N.Y. and attended the New Haven Connecticut high school. Upon graduation he entered Yale, receiving a degree in metallurgy in 1913. At that time Professor Mathewson was starting his plan of '"co-operation with the metal industries in metallographic work at the Hammond Laboratory of the Sheffield Scientific School, Yale University, and Arthur Phillip, became the first co-operative graduate student, working in the laboratory of the Bridgeport Brass Co., and receiving his Masters of Science degree in 1915. A little later, when the department of metallurgy at Yale was expanded. Me. Phillips was appointed assistant professor. In 1928 he was made associate professor, and in 1934 he was promoted to full professor.

Jan 1, 1944

By C. K. Leith

Jan 1, 1906

By AIME AIME

At the Annual Meeting of the Institute, February, 1908, the following amendments to the Constitution were proposed for action at a future business meeting (see Trans., XXXIX, xxvii) To Art. II. After the first sentence of this Article, add the following sentence « These classes may be subdivided by the Council, according to profession, length of membership, nationality, or other conditions not inconsistent with the provisions of this article." To Art. III. In the first line, substitute " fifteen " for "ten " dollars. At the Annual Meeting of February, 1909, action upon these amendments was postponed to the next business meeting (see Bulletin No. 27, March, 1909, p. xiv). Of these two amendments, the first has been withdrawn, as unnecessary-the subdivision thereby authorized being already practicable without such amendment. The second amendment will be acted upon at the next Annual Meeting, February 15, 1910, and the Secretary has been instructed to call the attention of members to the subject in such a way as to secure a general vote upon it. A special circular, now being prepared by the Secretary, will shortly be sent to all members. Year Book of the Institute. The Year Book of the Institute for 1910 is sent to all members and associates with this issue of the Bulletin. In addition to the lists of members enrolled Jan. 1, 1910, and arranged both alphabetically and geographically, this annual contains lists of officers, council, corporation, past officers, meetings, and notices concerning publications; also the constitution and by-laws of the Institute, and blank forms for proposal of mem-

Jan 1, 1910

By Victor O. Homerberg, Dexter N. Shaw

A study of the correlation of the mechanical properties and of the microstructure with the heat treatment of 60-40 brass has been confined, heretofore, to the rolled or extruded material as received from the mannfacturer. The results obtained by Babson and Buhler,' Bengough and Hudson12 Stead and Stedman,3 and Brayton4 have been confined to the treatment of the material as received. No attempt was made to get the material into a given condition and then to work from this basis. To start with a given structure would have the decided advantage of making the work independent of the original condition, hence, to make the results reproduceable. In a previous paper, it was shown, in connection with the study of the transformation that occurs at about 470" C., that if specimens were quenched to produce the beta structure and then reheated, the beta would begin to break down, at approximately 200" C., into a very finely divided alpha. It was predicted that important results might be obtained if test pieces were to be given a similar double heat treatment and then tested for the mechanical properties as well as a study of the microstructure. The material used in the present investigation was a 3/4-in. round bar of extruded muntz metal of the following composition: Copper, 61.05 per cent.; zinc (by difference), 38.90 per cent.; lead, 0.05 per cent.; iron, trace; tin, nil.

Jan 1, 1924

By Charles Fettke

IN THE present day manufacture of glass nearly pure quartz sands are used almost exclusively as the source of the silica, which is the major constituent of all common varieties of glass. Ordinary soda-lime, such as bottle, common tableware, plate, and window glasses, contain from 65 to 75 per cent. of silica. OCCURRENCE Glass sands occur in nature either in the form of loose, unconsolidated sediments or in deposits in which the individual grains have been more or less thoroughly bound together by some cementing agent so as to form sandstones. While deposits of sand and sandstones occur both widely and abundantly distributed, deposits that are sufficiently free from other constituents than quartz grains, so that they can be employed in the manufacture of the better grades of glass, are, comparatively speaking, of rare occurrence. The major portion of the glass sand produced in the United States comes from sandstones. In order to be suitable for glass sand, they should be rather friable. The rock should break down readily along the cementing material between the grains and should not break across the grains rather than along the bond. Some of the sandstones used are so friable that only light shots of slow-burning dynamite are necessary to disintegrate them sufficiently for hydraulic mining, while others have to be passed through crushers in order to disintegrate the rock into its individual grains.

Jan 2, 1926

By C. J. Haigh

Stockpiled and currently produced zinc plant residues containing zinc ferrite are to be treated at a rate of 350 tonne per day in a plant that is being constructed at the Risdon works of the Electrolytic Zinc Company of Australasia Limited (E.Z.). Start-up of the plant is scheduled for December, 1970. The residue is to be treated by a hydrometallurgical process that was developed by E.Z. in Australia, by Det Norske Zinkkompani in Norway, and by Compagnie Royale Asturienne des Mines (Asturiana de Zinc) in Spain. The process, as it is to be used at Risdon, is simple, consisting essentially of two stages : 1. A leaching stage at atmospheric pressure in which the zinc ferrite contained in zinc plant residue is dissolved in spent electrolyte, fortified with make up sulphuric acid, at a temperature in the range 70 to 95ºC. Undissolved solids containing lead and precious metals are separated for sale to a lead smelter. 2. An iron precipitation stage at atmospheric pressure in which ferric iron is precipitated from a slightly acidic solution at 90 to 95ºC as ammonium jarosite, a crystalline double sulphate which is relatively coarse, and is easily filtered and washed free of zinc-bearing solution. Calcine is used to neutralise the acid that is liberated during precipitation of the iron. Also included in the Risdon plant are a separate stage for oxidation of ferrous iron by injection of air, and a pre-neutralisation stage, using recycled oxidation stage pulp, to neutralise excess acidity from the leaching stage before the jarosite precipitation stage. The residue treatment plant consists of conventional equipment such as covered agitated vessels, thickeners and filters. Operation will be continuous and product solution will join the main zinc plant circuit for further purifications and electrolysis. Marketable zinc production will be increased by 70 tonne per operating day by the treatment of residue.

Jan 1, 1970

By H. P. Allen

THE chloridizing mill of the Standard Reduction Co. is located about 75 miles south of Salt Lake City on the Tintic branch of the Denver & Rio Grande Western R. R. and 12 miles from the Tintic Standard mine. The daily capacity is 200 tons of a siliceous, low-grade, silver-lead ore from this property. It has operated continuously since it was started in January, 1921. The process consists essentially of a chloridizing roast followed by a percolating leach with a nearly saturated solution of common salt, acidified with sulfuric acid, the precipitation of silver on sponge copper and of copper and lead on tin-plate cuttings. The precipitates are shipped to a smelter. Some of the general ideas involved are said to have been used by Augustin in England, in 1840. A number of textbooks treat of the subject, especially the chloridizing roast followed by a leach with sodium hyposulfite or amalgamation. The process was revived in this district by Theo. P. Holt, N. C. Christensen, the Bureau of Mines, and others.

Jan 8, 1925

By Robert Sisselman

Dramatic changes have been effected since 1955 in the mode of iron ore shipments within the U.S. In 1955, less than one percent of ore consumed in domestic blast furnaces-approximately 125 million long tons-consisted of pellets. Five years later, in 1960, some 94.8 million tons of ore were consumed, 14% in the form of pellets. Projections for 1980 reinforce confidence in this most economic of blast furnace feeds, and set U.S. pellet consumption at 151.2 million tons. In the last decade, pellets caught fire in other countries. By 1969, world production reached 96 million tons. This compares strikingly with present world output of 154 million tons.

Jan 9, 1973