Search Documents

By W. Rostoker, R. F. Domagala, R. P. Elliott

The phase equilibria of the Hg-Th system over the composition range 0-100 pct Th and temperatures up to 1000°C have been studied for a small-volume, closed system. The solubility of Th in liquid Hg is about 5 pct at 300°C and decreases sharply with decreasing temperature. Two intermediate phases occur, Hg3 Th and HgTh. The structures of these are hexagonal (nonideally close-packed) and face-centered cubic, respectively. The HgTh phase decomposes eutectoidally at 400°-500°C. The solubility of Hg in solid thorium seems to be negligible. AFULL-phase diagram for this system would have to be defined on temperature-composition-pressure co-ordinates. This paper describes the pseudo phase diagram of a closed system, that is, where the alloy enclosed in a small volume equilibrates with a vapor pressure of mercury dictated by composition and temperature. Because of the experimental difficulties in studying a system of this nature, many of the phase relations can only be sketched. Alloy Preparation Alloys over the full range of composition were made from triple distilled mercury and one of two grades of thorium. For the bulk of the work, a calcium-reduced metal in sintered pellet form of reported 99+ pct total thorium content was used. Arc-melted specimens of this thorium gave a hardness of 135 VPN. The microstructure showed small primary dendrites of ThO2. A number of alloy compositions were made with a high-purity, iodide-decomposition thorium metal. The are-melted hardness of a button of this material was 35 VPN. Although the microstructure of the arc-melted specimens showed no dendrites of ThO2, there was definite evidence of an unidentified phase enveloping the grain bound-aries. There were no distinguishable differences between the constitution of alloys made with the two grades of thorium metal. Under normal conditions thorium is not wetted by liquid mercury. The film of ThO2 on all thorium metal cannot be penetrated by either liquid or vaporous mercury. It was therefore necessary to comminute thorium in the presence of mercury under such conditions that oxide films could not reform on the newly exposed metal surfaces. This was accomplished by the use of a high-speed, carbide-tipped rotary cutter incorporated in a chamber purged with argon and connected at the bottom to a demountable Vycor bulb containing a weighed amount of mercury. This experimental device is fully described in a separate paper.1 Alloy compositions were calculated by weighing the empty bulb, the bulb containing the mercury, and the bulb containing the mercury and the thorium chips. Many alloys were analyzed chemically for thorium and/or mercury after subsequent homogenization; the agreement between analyzed and calculated compositions was invariably very close. Bulbs containing the requisite amounts of mercury and fine thorium chips were clamped off, removed to a sealing unit, evacuated and sealed. Amalgamation under these conditions proceeded rapidly even at room temperature. To insure homogeneity, the specimens were annealed to 300-400°C. Alloys containing less than 30 pct Th remained pasty after all treatments, indicating an equilibrium condition of liquid plus solid. Alloys with more than 30 pct Th were transformed into a dark powdery product. These latter specimens were annealed for times of up to 1 week to complete interdiffusion. Many of the alloy compositions are pyrophoric. On exposure to air they oxidize with considerable evolution of heat to a mixture of ThO2 and free mercury. It was mandatory that alloy specimens be handled in a "dry box" purged thoroughly with argon. All X-ray diffraction specimens were powdered, screened, and sealed in capillary tubes within the dry box. Experimental Procedures Thermal analysis experiments, useful only in the mercury-rich region of the system, were conducted with the alloys in their original containers. A reentrant thermocouple well formed an integral part of the bulb. These bulbs were heated in a silicone oil bath and cooled in a dry ice-acetone mixture. The rates of heating and cooling were slowed by immersing the specimen bulb in a larger tube containing silicone oil. This provided a suitable thermal lag. In all tests, pure mercury was run as a basic standard. While the invariant reaction at about the melting point of mercury was detected by thermal analysis, the heat effect at the liquidus was not sufficient to produce an inflection in the cooling curve. It was necessary to determine the liquidus temperatures at the mercury-rich end of the system by "breaks" in electrical reslstivity versus temperature curves for individual alloys. The apparatus for this purpose consisted of a pyrex tube about 2 in. diam and 12 in

Jan 1, 1959

By P. A. Witherspoon, S. P. Neuman

Evaluating the permeability of a caprock overlying a potential gas storage reservoir is a very critical problem. Pumping water from the reservoir can be used as an evaluation tool in analyzing this problem. Fluid level changes that occur in the aquifer us well as in the caprock can be measured with appropriately placed wells. If the leakage of water from the caprock into the aquifer is considerable, the effects will be apparent in the aquifer. If the leakage is slight, however, it will not be possible to detect it with certainty from observations in the aquifer alone. Fluid level measurements in the caprock must be relied upon. and improved methods of analyzing such effects have been developed which are based on a theoretical analysis of fluid flow through a caprock of infinite thickness. An example applying these methods to field data is discussed. INTRODUCTION One of the most critical problems in evaluating an aquifer gas storage project is determining the tightness of the caprock overlying the formation to be used as the storage reservoir. A formation that has previously held oil or gas obviously has a suitable caprock, but an aquifer that contains only water gives no such assurance. A number of aquifer projects in the United States have been troubled by gas leaking out of the intended storage zone, and the ensuing difficulties have led to the development of new evaluation methods. One of these new methods is pump testing wherein water is removed from the aquifer at some controlled rate prior to injection of gas. This fluid withdrawal causes a pressure drop to move out through the aquifer for considerable distances in a matter of days or weeks. Depending on the properties of the caprock, a pressure transient can also pass upward (as well as downward) through the caprock layers adjacent to the aquifer. Thus, if the operator has placed observation wells at appropriate distances from the pumping well, the rapidity with which the pressure transients reach different points in the system can be used to investigate the fluid transport properties of both the aquifer and its caprock. The usefulness of pump testing has been recognized by groundwater hydrologists for many years as a means of determining the potential yield and properties of aquifers used in water supply They have introduced the term "leaky aquifer" for a system in which an aquifer is overlain (or underlain) by semipermeable caprock layers. The ease with which water leaks into the aquifer during pumping can, of course, be very beneficial in bringing additional water to the pumped well. Hydrologists have therefore devoted considerable attention to this prob-lem. From the gas storage standpoint, however, the tighter the caprock layers that overlie the intended storage reservoir, the better are the conditions for minimizing or eliminating any vertical migration of gas. Thus, after a suitable geologic structure has been found, the emphasis in aquifer storage projects is in determining that the caprock is tight. Attention has recently been focused on the use of pump testing as one approach to solving this problem.23,24 This paper presents a further development on evaluating the permeability of a slightly leaky caprock when the caprock is of infinite thickness. From the practical standpoint, this means that the caprock layers are thick enough that pressure transients do not reach the outer boundaries of the system during the pumping test. In a subsequent paper, an analysis of the case where the caprock is of finite thickness will be presented. PREVIOUS WORK ON LEAKY AQUIFERS Jacob" developed a partial differential equation describing the flow of water in an aquifer of permeability k that is overlain by a leaky caprock of permeability k'. Fig. 1 shows a schematic cross-section of the system under consideration. One of his principle assumptions was that if k > > k', the direction of flow is essentially vertical in the caprock and horizontal in the aquifer. Neuman19 confirmed the validity of Jacob's assumption using a mathematical model. Another assumption was that a permeable source layer overlies the caprock (Fig. 1) and is able to maintain a constant hydraulic head at the upper boundary of the caprock. By neglecting the effects of compressibility within the caprock, Jacob1* developed a solution for a bounded circular aquifer. Later, Hantush and Jacobx5 used the same assumptions to solve the case of an infinite radial aquifer that is pumped at a constant rate. Their solution may be expressed in di-mensionless parameters by

By H. D. Hodges, J. K. Godbey

In order to better understand the fracturing process, bottom-hole pressures were measured during a number of typical fracturing operations. A recently developed system was used that allows simultaneous surface recording of both the bottom-hole and wellhead pressures on the same chart. The results from six fracruring treatments are summarized on the basis of the pressure data obtained. Al-though no complete analysis is attempted, the value of accurate pressure measurements is emphasized. Important characteristics of the bottom-hole pressure record do not appear at the wellhead because of the damping effect of the fluid-filled column. In four of the six treatments described, the formations apparently fractured during the initial surge of pressure with only crude oil in the well. The properties of the fluids used during the treatments are given and the fluid friction losses are obtained directly from the pressure records. This technique is also shown to be adequate for determining when various fluids, used during the process, enter the formation. INTRODUCTION Hydraulic fracturing for the purpose of increasing well productivity is now accepted in many areas as a regular completion and workover practice. Numerous articles have appeared in the literature discussing the various techniques and theories of hydraulic fracturing'. In general, three basic types of formation fractures are recognized today. These are the horizontal fracture, the vertical fracture, and fractures along natural planes of weakness in the formation'. Any one or all three of these fracture types may be present in a fracturing operation. However, with only the wellhead pressure record as a guide, it is difficult at best to determine if the formation actually fractured, and is almost impossible to determine the type of fracture induced. These difficulties arise in part because the wellhead pressure record, especially when fracturing through tubing, does not accurately reflect the pressure variations occurring at the formation. Several factors contribute to this effect and preclude the possibility of using the wellhead pressure as a basis for accurately calculating the bottom-hole pressure. These factors are: 1. The compressibilities of the fluids which damp the pressure variations. 2. The changes in the densities of the fluids or apparent densities of the sand-laden fluids. 3. The flowing friction of the various fluids and mixtures, which is dependent on the flow rates and the condition of the tubing, casing, or wellbore. 4. The non-Newtonian characteristics of a sand-oil mixture and its dependence upon the fluid properties, the concentration of sand, and the mesh size used. 5. The unknown and variable temperatures throughout the fluid column. Because of these reasons it was determined that in order to obtain a more accurate knowledge of the nature of fracturing, the bottom-hole pressure must be measured along with the pressure at the surface during a fracturing treatment. Even with accurate pressure data, a reliable estimate of the nature of fracturing is still dependent upon knowledge of the tectonic conditions. However, the hydraulic pressure on the formation is basic to any approach to a complete analysis. In order to accomplish this objective a system was developed to record the wellhead and bottom-hole pressures simultaneously at the surface. By recording both pressures on a dual pen strip-chart recorder, it was possible to greatly expand the time scale so that rapid pressure variations would be faithfully recorded. By such simultaneous recording, time discrepancies inherent in separate records are eliminated, thus overcoming one of the most difficult problems associated with bottom-hole recording systems. This paper illustrates the results obtained by using this system during six typical fracturing operations. All of these tests were taken in wells that were treated through tubing. By a direct comparison of the wellhead and bottom-hole pressures, the importance of obtaining complete pressure information during a fracturing treatment is emphasized. THE INSTRUMENTATION AND PROCEDURES The bottom-hole pressure measuring instrument consisted of a pressure-sensing element, a telemetering section, and a lead-filled weight or sinker bar. The pressure-sensing element used was an isoelastic Amerada pressure-gauge element. By using an isoelastic element, no temperature compensation was necessary in the tests described, since the temperature was believed to be well below the maximum temperature limit of 270°F. The rotary output shaft of this helical Bourdon tube element was coupled to a precision miniature potentiometer. The rotation of the pressure-gauge shaft thus changed the resistance presented by the potentiometer

By P. Pietrokowsky, T. E. Tietz, J. E. Dorn

The amount of solid solution hardening in aluminum alloys was found to be dictated by two factors: the lattice strain, and the change in the mean number of free electrons per atom of the solid solution. To obtain this correlation it was necessary to assume that aluminum contributes two electrons per atom to the metallic bond. WHEN the modern scientific method of analysis was first being formulated, Francis Bacon recorded in his "Essays" (circa 1600) that "an alloy . . . will make the purer but softer metal capable of longer life." During the intervening centuries voluminous data have been reported which demonstrate that the additions of alloying elements do in fact increase the hardness and strength of the pure metals. Nevertheless, the significant details of this problem on the unique effect of each element toward enhancing the mechanical properties of alloys only recently have been subjected to systematic scientific scrutiny. The major objective of this investigation is to determine how minor additions of alloying elements affect the plastic properties of polycrystalline aluminum alloys. By means of such studies it is hoped to provide not only data on the solution strengthening of aluminum alloys, but also a body of facts which will supplement the knowledge already available on the factors responsible for solution hardening in general. A review1"10 and analysis1' of the existing data on the effect of solute elements on the plastic properties of solid solutions reveal that our current knowledge on solid solution hardening is somewhat meager, inconsistent, and inconclusive. Many of the inconsistencies are undoubtedly attributable to the influence of unsuspected factors, such as purity; or uncontrolled factors, such as grain size, on the plastic properties of alloys. Nevertheless the following conclusions might be tentatively accepted: 1. Addition of solute elements invariably increases the yield strength, tensile strength, and hardness of the host element. 2. The rate of strain hardening, in general, increases with the concentration of the alloying element. 3. The strengthening effect in ternary alloys is the sum of the individual strengthening effects of the two solute elements as measured in their binary alloys. 4. The lattice strain is one factor that affects the strengthening of the alloy but it is not the only factor. 5. A second factor might be the difference in valence between the solute and solvent metals. All of the available evidence is in complete agreement with the first conclusion; the remaining conclusions, however, are not in agreement with all of the published data, but, in each case, the major weight of the existing evidence favors these deductions. Additional investigations will be required before most of these tentative conclusions can be accepted without reservation. In the following report an extensive investigation of the plastic properties of binary aluminum alloys is described. This work was undertaken in an attempt to shed more light on the general problem of solid solution hardening. Materials for Test: Aluminum was selected as the solvent metal for the present investigation on the effect of solute elements on the plastic properties of alloys. This choice was made for several reasons: (1) There appears to be little fundamental data in the published literature on the effect of solute elements on the properties of high-purity aluminum alloys. In view of the ever increasing economic importance of aluminum, such data would be of basic interest to the metallurgists concerned with the development of new aluminum alloys. (2) Aluminum is thought to be only partially ionized in the metallic state1' and consequently it might provide more complex relationships of the mechanical properties with the concentrations of the solute elements than more simple fully ionized solvents would reveal. (3) The data on aluminum alloys will provide a broader basis for correlations between the mechanical properties of metals in general and the concentration and atomic properties of the solute elements than is now available. Some complications, however, attend the selection of aluminum: The solubility of the various elements in the alpha aluminum phase are quite restricted, and not always well known. Consequently, only dilute solid solutions are available for study. This, however, may be somewhat advantageous because the dilute solution laws presumably are simpler than those applying to concentrated solutions. In addition, strain-hardened pure aluminum is known to recover at atmospheric temperatures. Very likely its alloys exhibit slower recovery rates. Thus, the secondary factor of effect of alloying elements on recovery might complicate the data. Such compli-

Jan 1, 1951

By E. C. Hopkinson, A. H. Youmans, R. A. Bergan, H. I. Oshry

A new log has been developed for quantitative formation evaluation which is based on a measurement of the length of time slow neutrons survive before they are captured in the rocks and fluids. The logging instrument employs a cyclically pulsed neutron generator and a gated scintillation counter which is synchronized with the source. The source emits short, intense bursts of 14 mev neutrons once every 1,000 microsec and is quiescent between bursts. During the period the source is quiescent, the detector is electronically actuated for two independent preselected intervals. A comparison of the counting rates during these two intervals gives a measure of the rate of decay of the slow neutrons and of the associated gamma radiation. The average neutron lifetime in most earth formations is in the range from 50 to 500 microsec. It can be measured during a continuous logging operation at conventional logging speeds. The design of the logging instrument is described and the results of tests are compared with theoretical predictiom. Formulas are developed which give the relationship between log response and formation properties. It is shown that the method is particularly sensitive to formation fluid salinity, and that salt water saturation can be measured accurately in either cased or open hole. The measurement can be made independent of borehole size, fluid type, casing and tool position in the hole by properly selecting the intervals during which the measurements are made. The results of tests with a prototype logging tool are given. INTRODUCTION A new nuclear logging system has been developed which employs the Accelatron,* an accelerator-type neutron source, and accurately measures formation brine saturation in an entirely new way. It has produced a type of formation log with better sensitivity, greater sampling depth and simpler quantitative interpretation than any other nuclear log thus far suggested. The new Neutron Lifetime Log* employs a pulsed electromechanical neutron source and a synchronously gated radiation detector. A prototype instrument has been field tested during recent months to demonstrate the operability of the apparatus and the feasibility of the method. Tests in wells and simulated boreholes have confirmed theoretical predictions and have shown that formation param ters can be measured independent of casing and other borehole parameters. Preliminary results of field tests have indicated that the log may have important and widespread applications. BASIC PRINCIPLE OF NEUTRON LIFETIME LOG The Neutron Lifetime Log is based on the fact that neutrons emitted by a source in a well are rapidly but not instantly captured by the material around the source. Their capture is a matter of statistical probability; the greater the number of capturing nuclei and the greater the "capture cross section", the greater is the probability that a neutron will be captured quickly. The average life of a thermal neutron in vacuum is about 13 minutes, but in common earth materials, the average neutron life ranges between extremes of about 5 rnicrosec for rock salt and perhaps 900 microsec for quartzite. The Neutron Lifetime Log responds to variations in this average neutron life. The theoretical basis for a log of this general type has been well understood by nuclear logging experts in many laboratories both in America and in Russia, and develop mental work along these lines has been in progress for many years. The Russian literature has reported both theoretical and experimental work1,2 but in this country there have been no published reports of progress toward a practical logging instrument. The logging instrument is designed to measure radiation produced by slow neutrons during selected intervals when no neutrons are being emitted by the source. The source is arranged to emit neutrons in bursts or pulses. During the quiescent interval between the pulses, it is possible to observe the exponential "decay" of the neutrons and the neutron-induced radiation as the individual neutrons progressively disappear due to capture by atoms in the formation or the borehole. When a short pulse of 14 mev neutrons is emitted by a source in a borehole, the individual neutrons are slowed to thermal energy within a few microsec. Thus, a cloud of "slow" neutrons is formed around the source within 10 to 50 microsec after the pulse. This cloud is most dense within a few inches of the source, and is progressively less dense out to a radius of about 3 ft, where radiation from the source is practically undetectable.

Jan 1, 1965

By R. R. Estill

THE rank of the Ruhr coal ranges from a high volatile bituminous coal to an anthracite, depending to some extent on the original depth of the seam. The average Ruhr coal corresponds to a soft bituminous American coal of a coking quality. The average thicknesses of individual coal seams being mined are also comparable (59 in. against 65 in. in the United States). However, consideration of seam conditions and mining conditions other than those just mentioned emphasizes differences rather than similarities with United States soft coal. In general, the Ruhr seams now being mined are much more folded and inclined than American seams. Dips of 20' and 30" are common in seams now being worked, and 30 pct of the coal reserves in the district are in seams dipping more than 35". Only on the tops and bottoms of folds do we find rather flat coal seams. In addition to the folding there is extensive displacement by cross faulting plus a certain amount of strike faulting of an overthrust nature, which results locally in doubling or omission of seams. Because of the long history of mining in the Ruhr, nearly all coal lying near the surface has long since been mined out, and we find that the average depth of mining is at present about 2300 ft below the surface. Deep mining, folding, and faulting result in seam conditions requiring a great deal more roof support than one finds in American soft coal mines. In fact only in the anthracite district and the Rocky Mountain and Pacific coal fields do we find somewhat similar conditions. It is easy to say, therefore, that the problem of mechanization of coal cutting and loading in the German mines is quite different from that which we have so effectively met in America with our mobile cutters and loaders, duck bill loaders, and a room and pillar system of mining our drift and slope mines. Partly because of more limited coal reserves, the traditional German mining system is largely the longwall method, which gives an almost complete coal recovery. Backfilling must be extensively practiced to protect the longwall faces, the over and underlying seams and workings, and especially the surface industrialized areas and barge canals. The German engineers have accordingly concentrated their efforts on the design of cutters, loaders, and conveyors suitable to longwall methods rather than room and pillar methods. Undercutters with cutter bars like American models have been in use in the Ruhr since well before World War 11. In 1941 they accounted for 8.5 pct of the production. This percentage, of course, includes coal which was undercut but nevertheless had to be broken down with air hammers or with explosives. The most common of these cutters is the Eickhoff Standard cutter (see fig. 1). This machine does about 95 pct of the undercutting in the Ruhr today, and is available with either compressed air or electrical power and in at least four different sizes. A variation of the cutter is this one with two cutter bars (fig. 2). At the end of 1947 about 200 of these machines and similar cutters were accounting for 13.2 pct of the total production, a production which was, however, only 60 pct of the 1941 production rate, so that the actual cutter tonnage was only up to a small amount over 1941. In 1941 about 3 pct of the production was accounted for by shearing machines making their cut perpendicular to the longwall face. They were similar to those used in the States. These machines are today considered obsolete and now account for only 0.7 pct of the total production. They are located at only a few mines and at present do not seem to have much of a future in the Ruhr. For the future, the Ruhr miner is looking forward to rather extensive mechanization of face work, with two major types of equipment being developed almost simultaneously. On one hand there is the development of cutter loaders for use in relatively hard coal. They represent the further extension of ideas developed after relatively long experience with the Eickhoff cutter. On the other hand there has been since 1942 an intense interest in the Ruhr in the development of face-stripping methods, particularly by the Kohlenhobel (coal plow) and its modification. At the end of 1947 these cutter loaders, Kohlen-hobels and scrapers together were actually accounting for only about 1.4 pct of total production while air hammers still broke 77.1 pct and as much as 1.2 pct was actually broken by hand picks. However,

Jan 1, 1951

By R. R. Estill

THE rank of the Ruhr coal ranges from a high volatile bituminous coal to an anthracite, depending to some extent on the original depth of the seam. The average Ruhr coal corresponds to a soft bituminous American coal of a coking quality. The average thicknesses of individual coal seams being mined are also comparable (59 in. against 65 in. in the United States). However, consideration of seam conditions and mining conditions other than those just mentioned emphasizes differences rather than similarities with United States soft coal. In general, the Ruhr seams now being mined are much more folded and inclined than American seams. Dips of 20' and 30" are common in seams now being worked, and 30 pct of the coal reserves in the district are in seams dipping more than 35". Only on the tops and bottoms of folds do we find rather flat coal seams. In addition to the folding there is extensive displacement by cross faulting plus a certain amount of strike faulting of an overthrust nature, which results locally in doubling or omission of seams. Because of the long history of mining in the Ruhr, nearly all coal lying near the surface has long since been mined out, and we find that the average depth of mining is at present about 2300 ft below the surface. Deep mining, folding, and faulting result in seam conditions requiring a great deal more roof support than one finds in American soft coal mines. In fact only in the anthracite district and the Rocky Mountain and Pacific coal fields do we find somewhat similar conditions. It is easy to say, therefore, that the problem of mechanization of coal cutting and loading in the German mines is quite different from that which we have so effectively met in America with our mobile cutters and loaders, duck bill loaders, and a room and pillar system of mining our drift and slope mines. Partly because of more limited coal reserves, the traditional German mining system is largely the longwall method, which gives an almost complete coal recovery. Backfilling must be extensively practiced to protect the longwall faces, the over and underlying seams and workings, and especially the surface industrialized areas and barge canals. The German engineers have accordingly concentrated their efforts on the design of cutters, loaders, and conveyors suitable to longwall methods rather than room and pillar methods. Undercutters with cutter bars like American models have been in use in the Ruhr since well before World War 11. In 1941 they accounted for 8.5 pct of the production. This percentage, of course, includes coal which was undercut but nevertheless had to be broken down with air hammers or with explosives. The most common of these cutters is the Eickhoff Standard cutter (see fig. 1). This machine does about 95 pct of the undercutting in the Ruhr today, and is available with either compressed air or electrical power and in at least four different sizes. A variation of the cutter is this one with two cutter bars (fig. 2). At the end of 1947 about 200 of these machines and similar cutters were accounting for 13.2 pct of the total production, a production which was, however, only 60 pct of the 1941 production rate, so that the actual cutter tonnage was only up to a small amount over 1941. In 1941 about 3 pct of the production was accounted for by shearing machines making their cut perpendicular to the longwall face. They were similar to those used in the States. These machines are today considered obsolete and now account for only 0.7 pct of the total production. They are located at only a few mines and at present do not seem to have much of a future in the Ruhr. For the future, the Ruhr miner is looking forward to rather extensive mechanization of face work, with two major types of equipment being developed almost simultaneously. On one hand there is the development of cutter loaders for use in relatively hard coal. They represent the further extension of ideas developed after relatively long experience with the Eickhoff cutter. On the other hand there has been since 1942 an intense interest in the Ruhr in the development of face-stripping methods, particularly by the Kohlenhobel (coal plow) and its modification. At the end of 1947 these cutter loaders, Kohlen-hobels and scrapers together were actually accounting for only about 1.4 pct of total production while air hammers still broke 77.1 pct and as much as 1.2 pct was actually broken by hand picks. However,

Jan 1, 1951

By Irving B. Cadoff, Ernest Levine

The crack formation and propagation in the single -phase Cu-4 pct Ag alloys were studied. The alloys were loaded in mercury to various stress levels, the mercury was removed, and the specimen examined for cracks. Cracks were found to develop below the fracture stress; the frequency of such cracks increased with increasing stress level. Some cracks were nmpropagative. Fracture in mercury was found to occur by the link-up of cracks formed at various stress levels rather than by the growth and propagation of a single crack. If the mercury environment is removed prior to a critical amount of crack formation, then continued loading results in ductile fracture. The appearance of the cracks at selected grain boundaries is related to the relative orientation of the boundaries, as are the propaga-tive characteristics of the crack. The mercury interaction appears to be one of lowering the strength of the metal-metal bonds in the high-stress area of the grain boundary. GRIFFITH'S microcrack theory1 proposed a critical crack size above which a crack in an elastic material grows with decreasing energy at a stress of From his theory it was proposed that the presence of a liquid tends to lower the surface energy of the microcrack faces2 leading to a decrease in the critical crack size necessary for spontaneous fracture propagation. stroh3 proposed that the stress concentration at a grain boundary due to pile-up may initiate a microcrack at the grain boundary. petch4 and Stroh5 evaluated the stress distribution at the head of a pile-up in a polycrystal-line material and deduced that the critical crack size and hence of is dependent on the grain size. Experimental verification of this dependence was found by petch6 for hydrogen embrittlement of steel. Studies in stress-corrosion cracking7 have provided a picture of fracture which shows that initial separations occur in a scattered, independent fashion in regions of high tensile stress. A minimum or threshold stress is necessary to produce a sufficient stress concentration to initiate frac- ture. These separations join up to form a crack. The extension of fracture is largely discontinuous and consists of a joining up of cracks. In recent worka evidence of this scattered crack network was found in a Cu-Ag alloy embrittled by mercury. For the Cu alloy-Hg couple, the crack path has also been found to be dependent on the orientation of adjacent grains, and with the addition of zinc to mercury a reduction in embrittlement along with a change in fracture morphology was found.9 In this present study, a mercury-dewetting method was used to observe crack initiation and fracture morphology when a Cu-4 pct Ag alloy is deformed in mercury and Hg-Zn solutions. PROCEDURE Specimens of Cu-4 pct Ag were prepared as in previous crack-path studies.' The specimens were heated at 770°C for 24 hr and water-quenched Tension tests using a table-model Instron were carried out in mercury and in various concentrations of Hg-Zn. Loading was in steps up to the fracture stress, with the load being removed and the specimen examined for surface cracks at each step. The specimens were dewetted after each load to permit examination of the surface structure and rewetted prior to continued loading. The specimens were wetted by electro polish ing in phosphoric acid, rinsing in alcohol, and then immersing in a pool of mercury. Dewetting was accomplished by flame heating the specimen for 30 sec in a vacuum. Some surface contamination was found, but not enough to obscure crack configurations and grain boundaries. RESULTS Fracture Characteristics in Mercury. Fig. 1 is a stress-strain curve showing the progressive step-wise loading of the specimen. As may be seen from the graph, the first position stopped at a is at a stress 5000 psi below the expected fracture stress of 25,000 psi. Examination of the specimen after removal of mercury showed only one crack. The appearance of this crack at a stress far below the fracture stress of this alloy in mercury did not affect the stress-strain curve in any manner. The specimen was then recoated with mercury and deformation was continued (curve b, Fig. 1) raising the stress by 4000 psi, and the same procedure re~eated. The initial crack was located and appeared as in Fig. 2 (crack lb). In this figure the crack is

Jan 1, 1964

By J. L. Gillson

Historically, rock deposits and sand deposits of titanium minerals came into production about the same time, although there may be some argument as to what is meant by production. Beach deposits of heavy minerals in India (Figs. 1-4) and Brazil (Figs. 5) were worked for monazite about the turn of century, but as there was then no market for titanium minerals, these were thrown away. The rock rutile deposits at Roseland, Va., Fig. 6, were worked to supply rutile for titanium chemicals and for coloring ceramics long before there was a titanium pigment business. The pigment industry started about the middle twenties, both in Europe and the U. S., and almost simultaneously the rock deposits at Ponte Vedra Beach near Jacksonville, Fla., were worked for titanium content. Since those days, production from both types of deposits has continued to grow at a rapid rate; many deposits of both types have been found, and reserves have grown to very large figures. In total tonnage of reserves, there is no doubt that the rock deposits are far ahead of the sand deposits; nevertheless there is a very large tonnage of commercial sands available. It is the quality of titanium mineral in the sand and the relatively lower costs of operating sand deposits that have kept them abreast, at least in annual tonnage produced, with the rock deposits. The principal titanium mineral used is ilmenite, but as soon as that mineral began to be sought as a titanium ore, it was obvious that there are ilmenites and ilmenites. Textbook ilmenite should have the composition FeOTiO2 and should analyze 52.6 pct TiO2 and 36.8 pct iron as Fe. The Indian ilmenite, for almost a generation the standard ore for manufacturing pigment in the U. S., was found to analyze about 60 pct TiO, and only 24 pct. Fe, and most of the iron is in the ferric condition. The whole process of pigment manufacture in the U. S. was built up on the use of a raw material of that grade, and the American chemical engineers who operate the pigment plants shuddered at the thought of using a rock ilmenite with 45 pct or so of TiO, and nearly 40 pct Fe. Intensive search was made around the world to find other deposits of rich black sand, like the Indian beaches, but although a few were found, there was some objectionable feature about each. A deposit in Senegal, south of Dakar (Fig. 7), was worked for a while, but an organic coating on the grains made attack by acid difficult. Modern practice would have included a scrubbing operation, in a caustic soda bath, to eliminate the organic coating. Brazilian deposits were numerous, but individually small, and shipping from them difficult. Deposits on the east coast of Ceylon had many attractive features, but the ilmenite analyzed only 54 pct TiO2 and could have been used only with a penalty. Sand deposits with 2 pct ilmenite, like those now worked in Florida, would not have been considered commercial ore, even if they had been known at that time. Most rock ilmenites are associated or mixed with hematite or magnetite, which accounts for the lower titanium and higher iron values than in the sand ilmenites. The Norwegians, English, and Germans, with cheap Norwegian rock ore at hand, learned to install in their pigment plants adequate capacity on the black side, as it is calltd, and counterbalanced the extra cost of plant, and larger amount of acid used, by the lower cost of ore. When World War II arrived, two of the largest pigment manufacturers in the U. S. had to learn how to use the Adirondack ilmenite, but one of them very gladly went back to sand ores when the Florida deposits came into large-scale production after the war. The other continues to use Adirondack ilmenite and finds it commercially attractive to do so. Rutile is not a raw material for titanium pigment manufacture by the sulfate process, since it is insoluble in sulfuric acid. In addition to its small consumption in chemicals and ceramics it began to be used in quantity in welding rod coatings. With the outbreak of World War 11, and the tremendous need for welding rods in shipbuilding and other structural steel construction, rutile suddenly became in heavy demand. The sand deposits on the eastern shore of Australia (Fig. 8A) which had been worked in a small way since 1934 were brought into production, and some stream placers in Brazil were worked and rutile concentrates shipped to American

Jan 1, 1960

By H. C. Rogers

A phenomenological study of the failure of polycry stalline ductile metals at room temperature was carried out using light and electron microscopy. Tensile fractures as well as sections of partially fractured bars of OFHC copper in particular were examined. The initiation and growth of the central crack in the neck of a tensile specimen occurs by void formation. After the formation of the central crack the f'racture may be completed in either of two ways: by further void formation or by an "allernating slip" mechanism. The first leads to a "cup-cone" failure; the second, to a "double-cup" failure. In the past decade or decade and a half there has been a great deal of emphasis on the solution of the problem of the brittle fracture of metals, particularly those which normally exhibit considerable ductility such as steel. Since the problem of the fracture of metals after large plastic strains has less immediate commercial or defense significance, there has been considerably less effort expended in describing the details of the phenomenology and determining the mechanism of this type of fracture. The present research was undertaken to increase our knowledge in this area. The problem of ductile fracture has not been neglected completely, however. Ludwik1 first found by sectioning a necked but unbroken tensile specimen of aluminum that fracture began with a large internal crack which appeared to have started in the center of the neck. Examination of the fracture indicated that the crack had propagated radially with increasing deformation until a point was reached at which the path of the fracture suddenly left this transverse plane and proceeded at approximately 45 deg to the stress axis until the surface was reached. This gives rise to the commonly observed cup-cone tensile fracture. When MacGregor2 was attempting to demonstrate the linearity of the true stress-true strain curve from necking until fracture, he found that copper was anomalous in that the stress dropped off markedly from the straight line value before fracture occurred. Radiography indicated that in the copper an internal crack was formed long before the final fracture, the stress decreasing during the growth of this crack. One of the most significant advances in the understanding of ductile fracture was the result of work by Parker, Flanigan, and Davis.3 By the use of etch-pit orientations they were able to demonstrate conclusively that the fracture surface at the bottom of the cup, although on a gross scale normal to the tensile axis, did not consist of cleavage facets as had been previously supposed by many investigators. Recently, Forscher4 has shown evidence of porosity near the tensile fracture of hydrogenated zirconium which he attributes to hydride decomposition. The workers at the Titanium Metallurgical Laboratory5 have also shown evidence of porosity in a number of the commonly used metals after heavy deformation. Many metals have relatively low ductility during creep tests at high temperature. The fractures are intercrystalline, resulting from the nucleation and growth of grain boundary voids. The work in this area has been recently reviewed by Davies and Dennison.6 It is possible that some of the observations and conclusions may have a bearing on the present study? especially since at least two studies7,' have been extended down to room temperature and below using magnesium alloys. However, since magnesium does exhibit low-temperature cleavage, these results may not be pertinent to the present one. The use of the electron microscope as an aid to the study of fractures has been extensively exploited by Crussard and coworkers.9 The examination of direct carbon replicas of the fractures of a large number of metals and alloys showed that the bulk of the fracture surface was covered with cup-like indentations of the order of 1 to 2 µ in size. These frequently had a directionality by which Crussard claims to be able to tell the direction of the crack propagation. With this rather disconnected background of information, this investigation was undertaken in the hope of presenting a unified picture of the initiation and propagation of a fracture in a ductile metal. To this end all of the techniques previously used were employed simultaneously so that there might be a good correlation of the data obtained by different techniques. EXPERIMENTAL PROCEDURE The metal which was chosen as the starting material for this investigation was OFHC copper. Of the dozen or so materials considered, it best fulfilled the requirements of commercial availability in large sizes, good ductility, relatively high melting point compared with room temperature and

Jan 1, 1961

By R. S. Sherwin

The extractive metallurgy of primary aluminum from its ores is discussed with special attention to the production of alumina from high grade ores by the Bayer process, including differences between American and European practice and a brief description of some processes for lower grade ores and the electrolytic reduction of the oxide to aluminum. METALLIC aluminum is not found in nature, but the oxides, hydroxides, and especially the silicates are plentiful. The estimated percentage of in in the crust of the earth is about 8 pct while that of iron is about 5 pct. By far the larger portion of this is combined with silica in the form of various clay minerals and igneous silicate rocks. From the point of view of extractive metallurgy of aluminum, these are low grade ores while the better qualities of bauxite are the high grade ores. There have been various definitions of bauxite but perhaps the best definition at the present time is that bauxite is a rock or earth commonly used as an ore of aluminum or its salts in which the aluminum is present predominantly as a hydrate or a mixture of hydrates and hydrous oxides. It contains varying amounts of oxides of silicon, iron, and titanium and traces of compounds of some of the less common elements. The silica is mainly combined with alumina as clay or clay minerals which are hydrous aluminum silicates, although a part of it may be present as quartz sand. On the American continents, the alumina is mainly present as gibbsite, Al2O3 . 3H2O, and the same may be said of the best known deposits of the Dutch East Indies and some of the deposits in India. In France and other countries in Europe as well as in Africa, the alumina is present mainly as boeh-mite, A12O3 . H2O, but in some of these deposits it is mixed with minor amounts of gibbsite. Some other deposits, such as those in the islands of Haiti and Jamaica, evidently contain two or more hydrates or hydrous oxides of alumina in varying proportions. Perhaps the main portion of the alumina may be present as gibbsite and boehmite with the proportion between the two varying rather widely. In the silicate minerals, including clay, the alumina is chemically combined with silica and has not been separated satisfactorily by mechanical or physical ore-dressing methods. Low grade bauxites are mixtures of hydrates, usually gibbsite or boehmite, with clay, iron oxides, etc. In some low grade bauxites, it is possible to separate a portion of the gibbsite or boehmite, which may be present as relatively hard and coarse particles, from soft or finely divided clay minerals by log washing or similar methods. This has been applied to the product of some mines or parts of them, but on other ores it is not applicable. In some cases the gibbsite or boehmite is almost as fine and soft and of nearly the same specific gravity as the clay minerals so that washing and gravity separations are not successful. The iron oxide, the clay minerals, and a part of the titanium minerals are often so finely dispersed in the ore that any of the physical mineral separation methods, including separations by gravity, particle size, flotation, and electrostatic or magnetic separation, have not been commercially SUCCESSFUL except on relatively small lots of ore. For these reasons, the only available methods of separation on the general run of ores have been methods which would be classed as chemical rather than physical or mechanical separations. Aluminum oxide can be reduced by carbon at temperatures above 1800°C to form metallic aluminum and aluminum carbide or nitride. The temperature for rapid reduction of aluminum oxide to metallic aluminum is about the boiling point of aluminum and above the temperatures necessary to reduce iron, silicon, and titanium so that the direct reduction of an aluminum ore with carbon will produce an alloy of aluminum, iron, titanium, silicon, etc., which may be mixed with carbides and nitrides. Also a large amount of the reduced aluminum may be lost as a vapor except in the presence of some alloying agent such as copper or other metals. While it is possible to refine such alloys or mixtures so as to produce commercially pure aluminum, the methods which have been found are too expensive for the present market. One direct reduction method which found limited commercial use in Germany during World War II was the direct reduction of a mixture of clay containing very little

Jan 1, 1951

By D. A. Dukelow, K. Li, G. C. Smith

Decarburization in the Fe-C system by oxygen top blowing has been studied in laboratory -scale experiments. It is shown that equilibrium models fail to explain or predict either the course of refining or endpoint conditions, giving results which either are incompatible with the chemistry of the system or do not satisfy material balance requirements. Also the path of decarburization was found to vary even for heats made under apparently identica1 conditions. A promising approach to analyzing the decarburization results is to relate oxygen efficiency fm carbon removal to bath carbon content. This relationship for Fe-C heats shows the same range of oxygen efficiencies as is obtained in pilot-plant and commercial heats using hot metal-scrap charges. This implies that oxygen transfer is primarily controlled by the decarburization reaction itself, independent of other refining reactions. Therefore, it should be possible to study separately decarburization and slag-metal reactions. DECARBURIZATION is probably the most important reaction in steelmaking. Not only is it a main reaction in the refining of iron to steel but it also provides the stirring action in the bath necessary for the diffusion processes to proceed at reasonable rates so as to make a steelmaking process practical. Kinetics of decarburization in the open-hearth process has been a subject of investigation for many years.&apos;-B It is generally accepted that at steelmaking temperatures the rate of homogeneous C-0 reaction is extremely high and cannot constitute a rate-controlling step. Diffusion of oxygen through a boundary film in the metal phase has been suggested by arken&apos; as rate-determining. Recently, Larsen and sordah16 concluded from experiments in a laboratory furnace that, with oxygen supplied from air or combustion gases, the rate of "steady-state" carbon boil is controlled essentially by a diffusion process of O2, Co2, or H2O through a film of nitrogen above the slag surface. Displacing this diffusion film by a stream of nearly pure oxygen produced a ten-fold increase in the rate of carbon boil with the rates of slag-metal oxygen transfer, bubble nucle-ation, and other steps all apparently able to keep pace. In the top-blown basic oxygen process, however, the transport of oxygen takes a more direct route. and the state of bath agitation is much more turbulent than in the open-hearth process. In addition, direct contact of the gas with the metal phase provides opportunity for direct oxidation of carbon. It is likely that the rate-limiting factor for the decarburization reaction will be different. However, only a few descriptive discussions of the subject have been reported in the literature.10-l2 Studies of the decarburization kinetics based on plant or pilot-plant data are necessarily complicated and are influenced by other refining reactions which occur simultaneously. In order to investigate the mechanism of decarburization, experiments have been conducted in which carbon-saturated iron melts were top-blown with pure oxygen over a range of conditions. It is hoped that this study will form a foundation on which a more basic understanding of this important reaction may be built. EXPERIMENTS One group of blowing experiments was made in a standard 200-lb induction furnace and another group in a 500-lb induction furnace. The furnaces were modified to the general shape of a basic oxygen furnace by adding a rammed refractory cone section to the regular crucible body. Crucible and cone were of high MgO (95 pct) material. A water-cooled lance, 1/2 in. in diam and threaded at one end to take a nozzle, was used for blowing oxygen. The lance with its water and oxygen lines was supported on a cantilever arrangement so that it could be moved up, down, or sideways. Oxygen of 99.5 pct purity was supplied from a cylinder and metered through a rotameter equipped with pressure and temperature gages. Another pressure gage was located at the top of the lance. A schematic diagram of the assembly is shown in Fig. 1. Before each experiment, a weighed amount of ingot iron, containing 0.02 pct C, < 0.01 pct Si, 0.10 pct Mn, 0.019 pct P, and 0.015 pct S, was charged in the furnace and melted down by induction heating. Graphite was then added to the molten charge until it became saturated. When the temperature of the charge reached the desired level, the lance was lowered to a predetermined height above the bath

Jan 1, 1964

By D. E. Thomas, C. E. Birchenall

ALTHOUGH Eoltzmann gave a mathematical solution for the diffusion equation (for planar diffusion in infinite 01. semi-infinite systems only) in 1894 allowing for variation of the diffusion coefficient with a change in concentration, it was not until 1933 that this solution was applied to an experimentally investigated metallic system. The calculation was carried out by Matano&apos; on the data obtained by Grube and Jedele3 for the Cu-Ni system. Since that time concentration dependence of the diffusion coefficient has been demonstrated for many pairs of metals. However, the nature of this dependence has never been fully elucidated. Many investigators have suspected that these variations could be related to the thermodynamic properties of the solutions, one of the earliest explicit statements being contained in a discussion of irreversible transport processes by Onsager&apos; in 1931. Development along these lines has been greatly retarded by the lack of reliable data on the variation of tliffusivity with concentration, the paucity of the thermodynamic data for the same systems at the same temperatures and compositions, and an incomplete understanding of the relation of the thermodynamic properties of the activated state for diffusion to the bulk thermodynamic properties. The last factor has been discussed by Fisher, Hollomon, and Turnbull.5 In many instances where data exist, it is difficult to know which are acceptable. This problem probably applies more strongly to diffusion data than to activity measurements. For instance, four sets of observers"-" have reported self-diffusion coefficients for copper. The average spread between extreme results is a factor of about four, though the individual sets of data are self-consistent to about 20 pct. Thus one or more factors are out of control, at least in these experiments, making estimates of internal error unreliable. The most reliable diffusion data in most systems have resulted from the use of welded couples with a plane interface from which layers for analysis are machined parallel to the interface after diffusion. The layers are analyzed, and the result is a graphical relation between distance and concentration, usually called the penetration curve. Given the same set of analytical data and distances and following the same procedure in computation, different observers will generally produce diffusion coefficients which vary appreciably, especially at the extremes of the concentration range. Experiments must be carefully designed so that the precision is good enough to answer a particular question unequivocally. In the first calculation of the dependence of the diffusion coefficient on concentration in the metallic solid solution Cu-Ni, Matano found that the coefficient was insensitive to concentration from 0 to 70 pct Cu, after which it rose more and more steeply to some undetermined value as pure copper was approached.&apos; The same behavior was reported for Au-Ni, Au-Pd, and Au-Pt.* The data used were those of Grube and Jedele which were very good at the time, but are not considered particularly good by present standards. Furthermore, the method of calculation makes the ends of the diffusion coefficient-concentration curve unreliable. For better reliability, the high copper end of the curve has been checked by incremental couples, where the concentration spread is 67.7 to 100 atomic pct Cu. The implication of the curves calculated by Matano was that diffusion is very concentration sensitive in one dilute range of this completely isomorphous system and hardly at all in the other. Matano&apos;s result is confirmed. Later Wells and Mehll0 published data on diffusion in Fe-Ni at 1300°C, which represent a thorough test of the shape of the concentration dependence curve. They ran couples with the following ranges of nickel concentration: 0-25 pct, 1.9-20.1 pct, 0-20.1 pct, 20.1-41.8 pct, 0-99.4 pct, and 79.3-99.4 pct. Although the trend of the data indicates an S-shaped concentration dependence, their curve was drawn to the pattern set by Matano. Their original data have been recalculated for the 0-99.4 and 79.3-99.4 pct couples. Wells and Mehl&apos;s points and two independent recalculations from the raw data are plotted in Fig. 1. What appears to be the best curve is drawn through them. This curve shows little sensitivity to composition in both dilute ranges with a strong dependence at intermediate composi-tions.? Similar experiments on the Cu-Pd system are reported here at temperatures where solubility is unlimited. These lead to the same type of concentration dependence for the diffusion coefficients as was found upon recalculation of the data for the Fe-Ni system. Experimental Procedure Cu-Pd: The concentration dependence of the diffusion coefficient may be determined by the use of

Jan 1, 1953

By G. L. Chierici

Starting from Muskat&apos;s theory of water and gas coning, maximum permissible oil production rates without water and/or free-gas production have been determined, in a broad range of reservoir and well parameters, using the potentiometric model technique. The main assumptions made are as follows: (1) the reservoir rock is homogeneeous (either isotropic or anisotropic); (2) the volume of the aquifer underlying the oil zone is very small, so that it does not contribute to reservoir energy; and (3) the gas cap expands at a very low rate, so that it can be assumed to be in quasi-static conditions. The results obtained are presented in the form of diagrams which can be used for solving two types of problems: (1) given the reservoir and fluids characteristics, as well as the position and length of the perforated interval, determine the maximum oil production rate without water and/or free-gas production; and (2) given the reservoir and fluids characteristics only, determine the position and length of the perforated interval which optimize the maximum permissible oil production rate, without water and/or free-gas production. INTRODUCTION In oil reservoirs where the oil-bearing formation is underlain by an aquifer which does not participate in the production mechanism, water-coning is a limiting factor to the flow rates of producing wells. Production rates are usually kept to a value that will prevent the water from entering the wells. The entry of water into a well lowers its productivity by increasing the weigbt of the fluid column; moreover, the separation of water from the effluent, at the surface, may constitute a very difficult problem in cases of heavy viscous oils. A similar situation is encountered in oil reservoirs with a gas cap overlying the oil-saturated zone; here a downward gas cone is induced by the flow of oil towards the producing wells. Production rates must be low enough to prevent the gas from being produced; producing gas from the gas cap would be a waste of energy. Of course, water-coning and gas-coning phenomena can occur at the same time in the same reservoir if the oil-producing formation is both overlain by a gas zone and underlain by a water zone. Due to its relevant practical importance, the mechanism of coning was studied by many people.2,3,5-8 Defining the conditions for getting the maximum water-free and/or gas-free oil production rate is a difficult problem, often encountered under one of the following aspects: 1. Predict the maximum flow rate that can be assigned to a completed well without the simultaneous production of water and/or free-gas. 2. Define the optimum length and position of the interval to be perforated in a well, in order to obtain the maximum water and gas-free production rate. A systematic study of these problems was made by means of the electrical analog technique. The results of this study are presented here, under the form of a set of curves providing solutions for the above stated problems. These curves are valid only for homogeneous forrnations, either isotropic or anisotropic. Should the formation be non-homogeneous (by horizontal or vertical variation of permeability, shale diaphragms, fractures, etc.), a specific potentiometric study would be required for each specific case. Especially when shale diaphragms of some radial extension are present, the critical rates observed are much larger than would be expected from the diagrams. STATEMENT OF THE PROBLEM In the present study the aquifer is supposed to be of such limited volume that it does not contribute to the energy of the reservoir. Moreover, the gas cap is supposed to expand at such a low rate that the potential gradient in the gas cap is negligible. Under static conditions water-oil and gas-oil interfaces (T1 and T2) are both horizontal. When the reservoir production starts, below each well these interfaces take a cone-like shape (Fig. 1) having as an axis the axis of the well. This shape results from the equilibrium between potential gradients in the oil zone and gravitational forces due to density differences between oil and water and between oil and gas. Assuming the oil-bearing formation to be homogeneous and the oil to be incompressible, the analysis of the problem (see Appendix) shows that the oil-water and gas-oil interfaces are stable only if the oil production rate of the well is not higher than the following values.

Jan 1, 1965

By John C. Sawyer

The mechanism of catastrophic oxidation of chromium and 446 stainless steel is examined. Data are presented to show that accelerated oxidation of these two materials, as caused by lead oxide, can occur in the absence of a liquid layer contrary to presently accepted theory. An alternate theory is proposed in which the rate of accelerated oxidation is a function of the rate at which lead oxide destroys the protective oxide formed on the base metal. An example of the application of the theory is given for the catastrophic oxidation of chromium in the presence of lead oxide. WHEN stainless iron-, nickel-, or cobalt-base alloys are heated in air to moderate temperatures in the presence of certain metallic oxides, oxidation will proceed at an accelerated rate. This phenomenon, often called "catastrophic oxidation", is most pronounced for the stainless steels. With these alloys the condition is so severe that large masses of oxide will form on the surface of the alloy in 1 hr or less at temperatures of 1200o to 1700oF. While a number of oxides are known to cause this effect, PbO, V2O5, and Moo3 are the most familiar, having been the subject of one or more investigations which have appeared in the literature.1-7 In presenting the results of these investigations, many of the authors have offered possible explanations to account for the more rapid rate of oxidation observed; however, the liquid layer theory as proposed by Rathenau and Meijering 2 has been the most commonly accepted mechanism. The liquid layer theory proposes that a low-melting oxide layer is formed on the surface of the alloy as the result of the interaction of the alloy oxide and the contaminating oxide. When the temperature of oxidation is above the melting point of the oxide on the surface, a liquid layer will form and oxidation will proceed at an accelerated rate. At temperatures below the melting point of the surface oxide, oxidation will proceed more slowly in the normal manner. It is argued that the rates of diffusion of oxygen and metal ions through the liquid layer are extremely rapid thereby accounting for the high rate of oxidation. Various experimental data have been presented to show that the temperature at which accelerated oxidation first becomes apparent coincides with the melting point of the eutectic oxide which would be present on the surface. Some exceptions have been observed, e.g., silver will oxidize in the presence of Moo3 at temperatures below the lowest melting eutectic; on the other hand, stainless steel will not be catastrophically oxidized at 1500oF in a molten bath of PbO and SiO2. In reviewing the various theories which have been used to explain catastrophic oxidation, Kubaschewski and Hopkins 8 favor the liquid layer theory, but note that, ".. .as experimental observations are not altogether in agreement with this theory (liquid layer theory), one should consider it a necessary but not a sufficient condition." In contemplating the liquid layer theory, it appears that sufficient evidence has not been presented to establish the theory beyond question. As a means of further clarification, a program of research was undertaken to determine in greater detail the mechanism of accelerated oxidation as caused by lead oxide. The first part of the program deals with a comparison of the oxidation of both AISI 446 stainless steel and chromium metal in the presence of lead oxide, vs the oxidation of these two materials in air alone. These comparisons are made at a number of different temperatures, most of which are below the melting point of the surface oxides. The second part of the program is concerned with a presentation of an alternate theory of accelerated oxidation exemplified by the system Cr-PbO-Air. PROCEDURE AND RESULTS Several experimental methods are commonly used to follow the progress of oxidation. One of these, the weight-gain method, was chosen for this work. This procedure requires that a specimen of the alloy be weighed, oxidized for a given period of time at an elevated temperature, and reweighed—the difference between the two weights being noted. The weight gain of the specimen represents the amount of oxygen acquired from the atmosphere to transform a portion of the specimen to oxide. In those cases where there is a tendency for the specimen or oxide to volatilize at the testing temperature, additional data must be collected so that a correction factor can be determined. This factor must be applied to the weight change in order to ascertain the actual amount of oxidation which has taken place. The specimens used for this work were 1 1/2 in.

Jan 1, 1963

By Anton Sawatzky, Erich Vogt

By means of mathematical solutions to the appropriate diffusion equations, we describe the kinetics of the thermal diffusion of hydrogen in Zircaloy-2 for the various temperatures and concentrations encountered in a heavy water moderated reactor. When the hydrogen concentration is below terminal solid solubility only the a Phase is present. Redistributions are then described in terms of the characteristic functions of the difhsion equation. For higher concentrations both the a and 6 phases are present. We assume the two phases to be always in equilibrium. For moderately small hydrogen concentrations exact solutions of the two-phase equation approach the the approximate solutions derived by Sawatzky and for all concentrations the exact solutions exhibit the qualitative features of his result: the two-phase concentration increases with time, everywhere; in the absence of a hydrogen current at the hot end of the sample an a-phase region always exists there; the interface of the a + 6 , a-phase boundary moves toward the cold md of the sample and the hydrogen concentration is discontinuous at the interface. Simultaneous solulions of the a and a + 6 hydrogen distributims and of the concomitant interface motion are obtained and compared to the observations of Sawatzky and Markowitz. The kinetics of the hydrogen diffusion process are shown to lead to m apparent heat of transport of the a phase which is lower than the actual value (even for samples with long anneals) thus resolving at least partially the disparity between experimental measurements of this quantity. A number of recent papers1"4 have reported measurements on the diffusion and redistribution of hydrogen in Zircaloy-2 under temperature and concentration gradients. These studies were instigated by problems arising from increasing use of Zircaloy-2 as a fuel element cladding material in pressurized-water power-reactors. The Zircaloy-2 picks up hydrogen during the operation of the reactor: the consequent precipitation of zirconium hydride in the Zircaloy-2 has pronounced effects on its mechanical properties. The Purpose of the present Paper is to describe the kinetics of the thermal diffusion of hydrogen in Zircaloy-2 for the various hydrogen concentrations and temperatures likely to be encountered in reactors. When the hydrogen in the Zircaloy-2 is entirely in the solid solution phase (a phase), the differential equation for thermal diffusion is well known and the redistribution can be described by standard mathematical methods some of which are given in Section 11 below. The treatment of the a + 6 (hydride) region differs from the earlier treatment of sawatzky3 by taking into account several modifications of the two-phase diffusion equations as suggested to us by Markowitz4 and Kidson.5 Even with the modifications the results obtained in our more complete treatment are substantially the same as those found by Sawatzky. As we show, the difference between the results of sawatzky3 and kIarkowitz4 is largely due to the difference in the geometry of their experiments. In the next section we derive the modified two-phase equation for arbitrary geometry. The exact solution of this equation is given in Section III for linear and cylindrical geometry. It is shown that Sawatzky&apos;s approximate solution is quite accurate for almost all the temperatures and hydrogen concentrations which are actually encountered. In Sawatzky&apos;s approximate theory the hydrogen concentration everywhere in the two-phase region increases continuously. As his paper pointed out, this result, together with hydrogen conservation, implies that in a sample with no hydrogen current flowing into the hot end a two-phase region is always accompanied by a single-phase region at the hot end of the sample. The net hydrogen gain in the two-phase region is supplied by the decrease of hydrogen in the single-phase region and by the movement of the (a, a + 6) boundary toward the cold end of the sample. Hydrogen conservation at the (a, a + 6) boundary leads to a discontinuity in the concentration and its derivative there. In Section IV it is shown how these qualitative features of the thermal diffusion kinetics arise from the simultaneous solution of the a-phase differential equation and a + 6 phase equation. Methods derived by us previously for the solution of the redistribution in both phases and the accompanying motion of the boundary are used to obtain approximate solutions valid for large times. The solutions account well for the observed redistributions of Sawatzky and Markowitz. It is shown how the continuing motion of the (a, a + 6) boundary leads to measured values of the heat of transport lower than the actual value, even for specimens with relatively long anneals.

Jan 1, 1963

By Lee Hillard Meltzer, Ralph E. Davis

INTRODUCTION During the past few years emphasis has been placed upon methods of estimating the future expectancy of gas production from natural gas fields. Before technical methods were applied, the production expectancy over future years was based upon the knowledge of gas well behavior, learned through long experience and embedded in the "know-how" of men long in the gas producing business. It is doubtful that a technical study of future expectancy of a gas field or a group of fields was ever prepared for the preliminary planning of a natural gas pipe line system built prior to about five years ago. The decline in well production capacity was naturally recognized by all familiar with the business since its earliest beginnings more than 75 years ago. In 1953, the Bureau of Mines published Monograph Number 7, "Back-Pressure Data on Natural Gas Wells and Their Application to Production Practices," which gave to the industry the first technical analysis of the decline in production of individual gas wells. This method affords a means of estimating the future production in relation to decline in reservoir pressure. The demand for technical determination of expectancy of future gas productivity from fields or a group of fields led technical men to the application of the knowledge of well behavior to the problems. The decline in a well&apos;s ability to produce as pressures declined could be estimated by the use of the curve known as the "back-pressure potential curve" as developed by the Bureau of Mines. A field containing few, or even numerous, wells could be analyzed on the basis of the sum of potentials of all wells. In most studies of this nature, the problem is to estimate the rate of production that can be expected, not only from present wells but also, from wells that will in the future have to be drilled into the reservoir being studied. The "back-pressure potential" method requires that the following data be known or estimated: (1) Proved gas reserves. (2) Current shut-in pressures and rate at which shut-in pressures change with production. (3) Back pressure potential data on wells in the source of supply. (4) Ultimate number of wells which will supply gas, and their potential. (5) Limitations on productivity such as line pressures against which the wells will produce, friction drop in the producing string, and so forth. It is evident that the resulting estimate of gas available in each year for a future of say, 20 years, contains many uncertainties. While the method may have considerable merit for a field that is fully developed, it cannot be completely dependable in fields that are only partially developed. In such cases, some of the data upon which it is based can only be estimated or assumed. In the study of this problem during the past few years, a method has been developed which we believe has great merit, especially when applied to fields subject to substantial future drilling, and when applied to the study of fields which, on the average, appear to have characteristics similar, in general, to the average of the fields used in the development of the "yardstick" outlined herein. From an analysis of the production history of 49 reservoirs which are depleted, or nearly depleted, a curve has been constructed which shows the average performance of the reservoirs during the declining stages of production. When properly applied, this "average performance curve" can be used to determine the stage of depletion at which a reservoir or group of reservoirs will no longer be able to yield a given percentage of the original reserves. "AVAILABILITY" AND "AVAILABILITY STUDIES" The rate at which. a reservoir will yield its gas depends basically upon physical factors, such as the thickness and permeability of the sand, the effect of water drive, if any, and other conditions, and upon economic factors, such as the number of wells drilled. Within the ranges set by the physical conditions, a rate of delivery tends finally to become established. The rate (or range of rates) represents a balance between the interests of the operator, who desires the maximum return from his property and of the pipe line owner, who desires to maintain a firm supply for his market. This balance, which is influenced by the terms of the contract, determines the capacity which will be developed by the operator, and the time and rate at which the decline in production is permitted to occur. Thus the "availability" of gas

Jan 1, 1953

By J. U. Messenger

A technique is described whereby the resistance of an emudian to breaking can be quantitatively determined. Produced ailfield emulsions are usually the water-in-oil type and, accordingly, do not conduct an electrical current. However, there is a threshold of A-C voltage pressure above which an emulsion will break and current will flow. The more stable an emulsion, the higher the required voltage. A Fann Emulsion Tester, modified so that low voltages (0 to 10 v) can be accurately measured, is suitable. This technique has application in evaluating the effect of a demuksifier on the stability of an emulsion. Emulsions can, in essence, be titrated with demulsifiers by adding a quuntity of demulsifier, stirring, and measuring the voltage required to cause current to flow. Any synergistic effect of two or more materials added simultaneously can be followed accurately. A demulsifier that significantly lowers the threshold voltage (from 100 to 400 v to 0 to 10 v for the emulsions in this study) is effective and can cause the enlulsion to break. A demulsifier that will bring about this drop in the threshold voltage at low concentration ir very desirable. The technique is also well adapted for rapidly screening demulsifiers. INTRODUCTION Stable emulsions in produced reservoir fluids resulting from certain well stimulation and completion procedures are common problems. The use of suitable demulsifiers can often mitigate these difficulties. At the present time, a rapid and efficient method for selecting satisfactory demulsifiers is not available. It is badly needed. Reliance is now placed primarily on trial-and-error procedures. A new test method has been developed which permits a more rapid and precise selection of demulsifiers. It involves measuring the electrical stability potential of an emulsion before and after a demulsifier has been added. This paper describes this method and shows where it should have application in field emulsion problems. NATURE OF OILFIELD EMULSIONS Two immiscible components must be present for an emuhion to form; we are concerned here with crude oil and water. An emulsifier must be present for tin emulsion to be stable. J Emulsifiers can be substances which are soluble in oil and /or mter and which lower interfacial tension. They can be colloidal solids such as bentonite, carbon, graphite, or asphalt which collect at the interface and are preferentially wet by one of these phases. Unrefined crude oils can contain both types of emulsifiers, A popular theory is that, of the two phases in an emulsion, the dispersed phase will be the one contributing most to the interfacial tension.&apos; Usually this phase contains the least amount of emulsifier. The stability of a water-in-oil emulsion is affected by the fol1owing: l) viscosity; (2) particle or droplet size; (3) interfacial tension between the phases; (4) phase-volume ratios; and (5) the difference in density between the phases. A stable emulsion is usually characterized by high-viscosity, small droplets, low interfacial tensions, small differences in density between its phases, and slow separatian of the phases. It also has low conductivity (high electrical stability potential). Water-in-oil and oil-in-water emulsions"&apos; are both common; however, oil field emulsions are predominantly water-in-oil emulsions. The emulsions which commonly occur during oompletion and stimulation operations contain a combination of several of the following: acids, fracturing fluids (oil, water, acid), and formation water and oil. Produced emulsions usually contain formation water and oil. Emulsions form in oil wells because oil and water are mixed together at a high rate of shear in the presence of a naturally occurring or unavoidably produced emulsifier. During the completion and stimulation of productive zones, and while formation fluids are being produced, oil and water are very often commingled. These mixtures are formed into emulsions by agitation which occurs when the fluids are pumped from the surface into the matrix of the formation or produced through the formation to the surface. Restrictions to flow (such as perforations, pumps, and chokes)".&apos;" increase the level of agitation; tight emulsions are more likely to form under these conditions. Often an emulsified droplet is an emulsion itself.&apos;" Therefore, emulsion-breaking problems can be quite complex. The complexity can be even greater if a third phase (gas) is included. Demulsifiers operate by tending to reverse the form of the emulsion. During this process, droplets of water become bigger, viscosity is lowered, color becomes darker, separation of the phases faster and electrical stability potential approaches zero. Any of these effects could be followed as a means of determining emulsion stability. However, electrical stability potential is the most reproducible and most easily measured parameter for following the stability of a water-in-oil emulsion.

Jan 1, 1966

By Vittal S. Bhandary, B. D. Cullity

Swaged iron wire has a cylindrical {001} <110> texture. The texture is also cylindrical after re-crystallization in the absence of a magnetic field, but <111> and <112> components are added to this texture when recrystallization occurs in a field. The mecizanical properties in tension and in torsion are not greatly altered by these changes in texture. AS shown in a previous paper,1 cold-worked wires of the two fcc metals copper and aluminum can be made relatively strong in torsion and weak in tension, or vice versa, by proper control of preferred orientation (texture). The deformation texture can be controlled by selection of the starting texture (texture before deformation), because certain initial orientations are stable during deformation. The present paper reports on similar work performed on bcc iron. In this case it was clear at the outset that there was no hope of controlling the deformation texture, which is one in which <110> directions are aligned parallel to the wire axis. (1t has usually been regarded as a fiber texture, but Leber2 has recently shown that it is a cylindrical texture of the type {001} <110>. In either case, <110> directions are parallel to the wire axis.) There is general agreement on this texture among a large number of investigators, which in itself suggests that the starting texture has no influence on the deformation texture. More direct evidence was produced by Barrett and Levenson,3 who reported that iron single crystals of widely varying initial orientations all had a single <110> texture when cold-worked into wire. Thus <110> is a truly stable end orientation for iron and probably for other bcc metals as well. Under these circumstances attention was directed to the possibility of controlling the recrystallization texture. This texture is normally <110> in iron,4 just like the deformation texture. However, it is conceivable that this texture could be modified by a proper choice of the time, the temperature, and what might loosely be called the "environment" of the recrystallization heat treatment. In the present work the environmental factor studied was a magnetic field. The effect of heating in a magnetic field ("magnetic annealing") on recrystallization texture has been investigated by Smoluchowski and Turner.5 They found that a magnetic field produced certain changes in the recrystallization texture of a cold-rolled Fe-Co alloy. The texture of this material is normally a mixture of three components, and the effect of the field was to increase the amount of one component at the expense of the other two. Smoluchowski and Turner concluded that the effect was due to magnetostriction. With the applied field parallel to the rolling direction, the observed effect was an increase in the amount of the texture component which had <110> parallel to the rolling direction. In the Fe-Co alloy they studied, the magnetostriction is low in the <110> direction and high in the <100> direction. Thus nuclei oriented with <110> parallel to the rolling direction will have less strain energy than those with <100> orientations and will therefore be more likely to grow. In a later paper on the same subject, Sawyer and Smoluchowski6 ascribed the effect to magneto-crystalline anisotropy and made no mention of magnetostriction. In the papers of Smoluchowski et al. the intensity of the magnetic field was not reported but it was presumably large, inasmuch as it was produced by an electromagnet. In the second paper6 it is specifically mentioned that the specimens were magnetically saturated. But if magnetostriction has a selective action on the genesis of stable nuclei during recrystallization, that selectivity must depend only on differences in magneto-strictive strains between different crystal orientations and not on the absolute values of those strains. Thus the saturated state does not necessarily produce the greatest selectivity, because the relative difference in magnetostrictive strains between different crystal directions may be larger for partially magnetized crystals than for fully saturated ones.7 In the present work the specimens were subjected to relatively weak fields (0 to 100 oe) produced by solenoids. MATERIALS AND METHODS Armco ingot iron rod (containing 0.02 pct C and 0.19 pct other impurities) was swaged from 0.25 in. in diam. to 0.05 in., a reduction in area of 96 pct. The mechanical properties in tension and torsion were measured as described previously.&apos; Textures were measured quantitatively with chromium or iron radiation and an X-ray diffractometer,8,1 and

Jan 1, 1962

By F. A. Forward, J. Halpern

A new process for extracting uranium from ores with carbonate solutions is described. Leaching is carried out under oxygen pressure to ensure that all the uranium is converted to the soluble hexavalent state. By this method), alkaline leaching can be used successfully to treat a greater variety of ores, including pitchblende ores, than has been possible in the past. The advantages of carbonate leaching over conventional acid leaching processes are enhanced further by a new method which has been developed for recovering uranium from basic leach solutions. This is achieved by reducing the uranium to the tetravalent state with hydrogen in the presence of a suitable catalyst. A high grade uranium oxide product is precipitated directly from the leach solutions. Vanadium oxide also can be precipitated by this method. The chemistry of the leaching and precipitation reactions are discussed, and laboratory results are presented which illustrate the applicability of the process and describe the variables affecting leaching and precipitation rates, recoveries, and reagent consumption. THE extractive metallurgy of uranium is influenced by a number of special considerations which generally do not arise in connection with the treatment of the more common base metal ores. Perhaps foremost among these is the very low uranium content of most of the ores which are encountered today, usually only a few tenths of one percent. A further difficulty is presented by the fact that the uranium often occurs in such a form that it cannot be concentrated efficiently by gravity or flotation methods. In these and other important respects, there is evident some degree of parallelism between the extractive metallurgy of uranium and that of gold and, as in the latter case, it has generally been found that uranium ores can best be treated directly by selective leaching methods. It is readily evident that this parallel does not extend to the chemical properties of the two metals. Unlike gold, which is easily reduced to metallic form, uranium is highly reactive. It tends to occur as oxides, silicates, or salts. Two ores are of predominant importance as commercial sources of this metal: pitchblende which contains uranium as the oxide, U3O51 and carnotite in which the uranium is present as a complex salt with vanadium, K2O-2UCV3V2O5-3H2O. These ores may vary widely in respect to the nature of their gangue constituents. Some are largely siliceous in composition, while others consist mainly of calcite. Sometimes substantial amounts of pyrite or of organic materials are present and these may lead to specific problems in treating the ore. Further complications may be introduced by the presence of other metal values such as gold, copper, cobalt, or vanadium whose re- covery has to be considered along with that of the uranium, or whose separation from uranium presents particular difficulty. In general, there are two main processes for recovering uranium in common use today.&apos;.2 One of these employs an acid solution such as dilute sulphuric acid to extract the uranium from the ore. A suitable oxidizing agent such as MnO, or NaNO, is sometimes added if the uranium in the ore is in a partially reduced state. The uranium dissolves as a uranyl sulphate salt and can be precipitated subsequently by neutralization or other suitable treatment of the solution. The second process employs an alkaline leaching solution, usually containing sodium carbonate. The uranium, which must be in the hexavalent state, is dissolved as a complex uranyl tricarbonate salt, and then is precipitated either by neutralizing the solution with acid or by adding an excess of sodium hydroxide. The latter method has the advantage of permitting the solutions to be recycled, since the carbonate is not destroyed. This is essential if the process is to be economical, particularly with low grade ores. With each of these processes, there are associated a number of advantages and disadvantages and the choice between using acid or carbonate leaching is generally determined by the nature of the ore to be treated. In the past, more ores appear to have been amenable to acid leaching than to carbonate leaching and the former process correspondingly has found wider application. With most ores, acid leaching has been found to operate fairly efficiently and to yield high recoveries. One of the main disadvantages has been that large amounts of impurities, such as iron and aluminum, sometimes are taken into solution along with the uranium. This may give rise to a high reagent consumption and to difficulties in separating a pure uranium product. Excessive reagent consumption in the acid leach process also may result

Jan 1, 1955