Search Documents

By Kenneth Schellinger

THE terms surface tension and surface energy are well known when applied to liquids and are generally described by referring to the excess energy of the air: liquid interface as a result of unsaturated molecular forces surrounding the surface molecules of the liquid due to the presence of the air phase on one side. Such unbalanced forces produce the familiar water droplet of spherical form and are generally summed up as a surface tension measured in dynes per centimeter which can be shown mathematically to be equal numerically to a corresponding surface energy expressed in ergs per square centimeter. A specific surface energy, however, is best thought of as the energy necessary to produce one unit, of new surface on a substance. Hence, in producing a bubble in a flotation cell the impeller must supply surface energy corresponding to the air: liquid interfacial area on the interior of the bubble. Inasmuch as it is relatively easy to extend or contract the surface of a liquid, there are a number of successful methods for liquid surface tension, or energy, measurement based upon surface deformation. This happy state of affairs does not, however, extend to solids, which are considered to possess surface energies for the same reasons as do liquids, i.e. because of unsaturated ionic bonds at the solid: gas interface. As in the case of the flotation cell producing surface on liquids as new bubbles, it takes energy to produce new surface on solids as new particles. As every mill man knows, this surface is produced on mineral solids in a grinding mill by the action of a tumbling mass of iron balls. But here so much energy usually is wasted by the inefficient action of these balls that a large amount of heat is generated, and the surface energy production may be easily confused with the energy necessary to produce this ineffective heat. The tumbling balls and fracturing minerals ultimately take their energy from a rather large electric motor. It has been variously estimated that from 10 to 20 pct'" only of this energy from the motor does not appear as heat and may be presumed to appear as surface energy on the min- erals present. Such a production of new surface on the mineral phases is accompanied, of course, by a size reduction that is inevitable as more and more mineral interior molecules become surface molecules by the fracture exposure. This size reduction of mineral particles, although the most obvious feature and perhaps the sole object of the milling operation, is from this energy viewpoint the outward manifestation of the production of surface energy only. Measurement of the characteristic surface energies of pure minerals and their various mixtures in ores would be a step towards understanding of the energetics of the commercial grinding operation. In addition, the characteristic surface energy of a mineral is probably a physical property specific for that mineral, and therefore, from a scientific standpoint, should be measured. It is interesting to note that, in contrast to the large body of work on the surface tensions of liquid systems and biological systems, the field of solid surface energies has been neglected. Prior to 1920 it is difficult to find more than one or two references to work on solid surface energies in Chemical Abstracts. Since 1920 such references number somewhat less than 100, while those on liquid systems are numbered in the thousands. Much of this apparent neglect of the field of solid surface energies (the term is intended to be somewhat inclusive at this point and refers both to the solid: gas, and the solid:liquid interface) is because of the lack of a reliable method of measurement rather than any lack of scientific curiosity. It was, and still is, difficult to produce new surface on a solid without the simultaneous production of interior changes in the same solid which may consume part of the energy used. The extension in the surface area can be measured, but the interior crystal-

Jan 1, 1953

By John H. Schemel

Large Zircaloy-2 hammer or press forged bars did not exhibit the uniform excellent corrosion resistance to steam normally expected of the alloy in wrought form. Weight gains of coupons cut from forged bars were 40 to 60 mg per sq dm compared to the 28 mg per sq dm obtained on hot rolled sheet and strip. The mechanism of this corrosion and its relation to microstructure is discussed. After these observations, a solution heat treatment followed by rapid cooling was tried on coupons from eight heats of forged bars. The basket-weave structure resulting from the quench did not show agglomeration of intermetallic compounds. These coupons showed uniformly good corrosion resistance with weight gains very close to the 28 mg per sq dm expected of Zircaloy-2 after the 14-day steam test. A large forging was solution heat-treated and tested for structure, mechanical properties, and corrosion resistance. Corrosion resistance was excellent and uniform throughout the section. The normally anisotropic mechanical properties were changed to completely iso-tropic. Strength levels were raised while there was a small loss in ductility at the service temperature. Tempering of the quenched structure below the ß transus did not improve the ductility at the test temperature of 600°F. ZIRCALOY-2 end caps for nuclear fuel elements Zircaloy-2 is an alloy of 1.5 pct Sn, 0.1 pct Fe, 0.1 pct Cr, and 0.05 pct Ni, balance hafnium-free zirconium patented by Westing-house Electric Co. used in pressurized water reactors are machined from large hammer-finished forged bars. The bars forged for this application range from 3 1/2 in. to 7 1/2 in. squares. One of the tests used to evaluate Zircaloy-2 for this service is a 14-day exposure to very high-purity steam at 75oF and 1500 psi pressure. Normally wrought products will exhibit a black lustrous film of zirconium oxide after the test and show a weight gain of approximately 28 mg per sq dm. Coupons representing the forged bars exhibited a wide variety of corrosion results ranging from acceptable black coupons to some covered with white crystals of zirconium oxide that had weight gains of nearly 100 mg per sq dm. One of the most common effects was a white corrosion product that looked like a stain to some observers and the outline of massive metal grains to others. Very careful specimen preparation prior to the corrosion test did not affect the result and metallographic examination did not reveal a structural feature of a size and shape that would correlate with the corrosion product. In addition to the relatively poor corrosion resistance, the forged product was not as ductile as desired. The problem of obtaining uniform and more acceptable properties in these heavy-forged sections seemed to be a function of the microstructure of the metal and, in particular, the distribution of the intermetallic compounds. None of the four alloying elements however are appreciably soluble in a zirconium and are present as compounds which usually appear scattered randomly throughout the structure. Moudryl showed that the distribution of these intermetallic compounds in Zircaloy could be related to a ostringero corrosion failure. Grozier et al. discussed another structural defect that causes a similar corrosion effect. In this case, an elongated gas-void was determined to be the cause. M. L. Picklesimer held in his discussion of the Grozier paper that at least a part of the observed =stringersn were caused by the distribution of the intermetallic compounds. He proposed a

Jan 1, 1962

By C. D. Stahl, S. M. Farouq Ali

This investigation attempts to describe and simulate the alcohol displacement process by means of a cell model, as employed in chemical engineering practice. The proposed model is more simple than previously proposed models. and utilizes parameters chosen on a theoretical basis. The model successfully reproduced the formation of the stabilized bank and the breakthrough of alcohol, the latter depending on one of the model parameters, which may be correlated with the length of the porous medium. Moreover, the effects of the phase behavior of the liquid system involved, as observed in experimental studies, were reproduced. Several variations of the basic model were devised and tested on a digital computer. These included the cases in which: (1) the actual value of fractional flow was used in cell-to-cell computations; (2) the number of cells was varied within the same run; and (3) incomplete rather than complete phase equilibrium was assumed within each cell. The proposed cell model clarifies the basic mechanism of the process. Detailed concentration profiles obtained for each cell, for instance, showed the mechanism of bank formation in relation to the phase behavior characteristics. The results obtained indicated a varying degree of phase equilibrium concommitant with changes in the velocities of the phases in an actual alcohol displacement. This condition was approximated by changing the number of cells during the simulation. Interesting information was obtained on the influence of path length on the efficiency of alcohol displacement, which has been the subject of some controversy. Certain limitations preclude the use of the proposed model as a substitute for experimental studies. The results obtained were, nevertheless, of value in interpreting the experimental results. INTRODUCTION During recent years considerable effort has been directed toward an understanding of alcohol displacement, the process whereby oil and water are recovered from a porous medium by the continuous injection of a solvent. The complex nature of the physical process involved has so far defied a complete mathematical treatment. Other methods of approach, amounting to an overall material balance, have been proposed, yielding useful information on certain aspects of the process.1-3 Taber et al, in particular, defined the displacement mechanism in terms of the phase behavior of the alcohol-oil-brine system invoIved.2 Wachmann reported a mathematical treatment of alcohol displacement subject to certain simplifying assumptions? Donohue proposed the use of a "cell model" for simulating alcohol disPlacement.5 The nature of the assumptions involved limited the utility of the model. The present work attempts to examine the variables involved in the simulation of alcohol displacement and discusses several possible versions of the basic cell model. Under certain conditions the model results are similar to the experimental results. In particular, the spontaneous formation of of the stabilized bank and the effects of the system phase behavior were successfully reproduced. PREVIOUS WORK ON CELL MODELS Cell models and the theoretical plate concept are often used in solving chemical engineering problems in which an explicit mathematical solution may be difficult or impossible to obtain. Examples of such applications occur in distillation, gas-liquid chroma tography,6 reactor technology, absorption, etc. In petroleum engineering, such a model was used by Attra7 to describe non-equilibrium gas drive, and by Higgins and Leigh ton8 to calculate sweep efficiency in water flooding. Aris and Amundsen pointed out the equivalence between the diffusion model and perfectly mixed cells connected in series.9 Deans proposed a three-parameter cell model to simulate two-component

Jan 1, 1966

By J. F. Breedis

The morphology and crystallography of marten -site formed during quenclzing were examined by transmission electron microscopy in alloys whose compositions lie between Fe-19 wt pct Cr-11 wt pet Ni and Fe-33 wt pet Ni. Depending upon composition, four types of transformation products were observed in this portion of the Fe-Cr-Ni system. Three of these products are denoted as lath, plate, and surface martensite. The hcp structure found in association with martensite it? certain higlz-clzromium stairzless steels does not influence the transformation crystallogyaphy and cannot he Considered to act as a transitional structure in the transformation from austenite to martensite. DISTINCT changes in the characteristics of mar-tensitic transformations are produced by the partial replacement of nickel by chromium in austenitic iron alloys. Large, discrete martensite plates form in Fe-30 pct Ni, while aggregates of small crystals form in sheets parallel with (111)A austenite planes in stainless steels containing in the vicinity of 18 pct Cr and 8 pct Ni. These transformation structures are termed plate and lath martensite, respectively. In addition, an hcp structure (E) has been observed in certain high-chromium stainless steels in association with martensite. It has been suggested that the E structure acts as an intermediate step in the nucleation of martensitel-' and influences the morphology and crystallography of the final transformation product. However, this structure may be the consequence of the deformation of austenite arising from the shape distortion accompanying the transformation to bcc martensite.' An hcp stacking of atoms is produced in an fcc lattice by the introduction of an intrinsic stacking fault on alternate (111)A planes. At present, the arguments behind each explanation for the E structure are based on circumstantial evidence. This investigation seeks to determine the importance of the hcp structure to the martensitic transformation, and to examine the crystallography and morphology of the structures produced in bulk samples by quenching in alloys whose compositions lie between Fe-19 wt pct Cr-11 wt pct Ni and Fe-33 wt pct Ni. These aspects of the martensitic transformations occurring in these alloys have been studied by electron metallography and selected-area diffraction of foils examined in transmission in the electron microscope. EXPERIMENTAL METHODS The alloys have been prepared from thoroughly mixed powders of pure iron (99.6+ pct, 0.06 max pct C, 0.15 max pct N), chromium (99.9+ pct), and nickel (99.9+ pct). After sintering in an Ar-H2 atmosphere, the mixtures were melted by induction heating in recrystallized alumina boats under purified argon. The ingots were cold-rolled to 0.4-mm sheets (100 pct reduction in thickness) after the removal of at least 1.5 mm from their surfaces by grinding. Three-millimeter discs were punched from the cold-rolled sheet and annealed at 1150°C for approximately 24 hr in evacuated quartz capsules. The average grain size was 40 µ Thin foils for examination in transmission in the electron microscope were prepared from discs quenched to liquid-nitrogen temperature. A depression was first jet-machined into the center of a disc and a thin area (less than approximately 3000A in thickness) was produced at the base of the depression by electropolishing. Electron-microscope studies utilized the RCA EMU-3 and the Philips EM-100B microscopes operating at 100 kv. X-ray examination of the polycrystalline alloys was performed either in a diffractometer or in a

Jan 1, 1964

By Frederic L. Kadey

Diatomite is a siliceous, sedimentary rock consisting principally of the fossilized skeletal remains of the diatom, a unicellular aquatic plant related to the algae. Thus, it has been formed by the induration of diatomaceous ooze, and consists mainly of diatomaceous silica, a form or variety of opal which is first formed in the cell walls of the living diatom. Diatomaceous silica is not generally regarded as a synonym or the equivalent for diatomite, although it has been so used at various times. Accurately, diatomaceous silica is the preferred name for the principal mineral component of which the rock, diatomite, is composed. The terms diatomaceous earth and kieselguhr are used as synonymous with diatomite. The designations tripoli, tripolite, infusorial earth, etc., were used at one time but are now obsolete. With the changing nomenclature, these terms that were at one time correct when proposed and used for generations would be considered incorrect if used today in the light of current knowledge. The designation diatomite is reserved for those accumulations of diatomaceous silica that are of sufficient quality, size, and minability to be considered of potential commercial value. Processed diatomite possesses an unusual particulate structure and chemical stability that lends itself to applications not filled by any other form of silica. Foremost among these applications is its use as a filter aid, which accounts for over half of its current consumption. Its unique diatom structure, low bulk density, high absorptive capacity, high surface area, and relatively low abrasion are attributes responsible for its utility as a functional filler and as an extender in paint, paper, rubber, and in plastics; and as an anti-caking agent; thermal insulating material; catalyst carrier; and chromatographic support; polish, abrasive, and pesticide extender to name a few representative applications. The United States is the principal producing country, although diatomite is found in numerous other locations. Geology Composition and Morphology Diatomaceous silica qualifies as a. mineral of organic origin in much the same way that aragonite and collophane do. The silica of the fossilized diatom skeleton closely resembles opal or hydrous silica in composition (SiO2 • nH2O) .4, 12, 203 The silica is of acute biological significance, not only for the cell wall component, but also for the basic life process.45, 51 Without silica, cell development ceases .31 In addition to bound water, varying between 3.5 and 8%, the siliceous skeleton may also contain, in solid solution, or as part of the Si02 complex, small amounts of associated inorganic components-alumina, principally-and lesser amounts of iron, 46, 49, 55 alkaline earths, alkali metals, and other minor constituents.59, 63, 67 Boron is reported to be an essential element for diatom growth .52, 58 Since diatomaceous silica is not pure hydrous silica but contains other intimately associated elements, there is good reason to consider it a distinct type or variety.4 Associated with the diatomaceous silica, and integrated as part of the diatomite, may be variable amounts of organic matter, soluble salts, and particles of rock-forming minerals that were syngenetically deposited or precipitated with the diatom frustules. Sand, clay, carbonate, and volcanic ash are typical common contaminants. Other contaminating minerals may be present, such as feldspar, mica, amphiboles, pyroxenes, rutile, zircon-the result of weathering, then transporting, and subsequent redeposition of surrounding land masses. Commercial diatomite may also contain fragments and particles of

Jan 1, 1983

By Robert E. Green

Experiments were performed in order to investigate the influence of magnitude of driving force, recouery, and previous heat treatment on grain boundary migration in deformed aluminum crystals. The frequency of occurrence of strain-free grains possessing Preferred crystallographic orientations was studied both as a function of heat treatment and as a function of amount of deformation of the matrix crystal. Aluminum of such composition as to exhibit precipitation-hardening behavior was used. CONSIDERABLE work has been devoted to the factors influencing grain boundary migration in metals.1'52 Aust and Rutterl-9 have studied grain boundary migration into matrix crystals containing a striation substructure, which provided a thermally stable driving force during the course of the migration experiments. These authors state that, while variations in the striation pattern were sometimes observed, it was possible to obtain reasonably uniform and reproducible striation structure by careful control of the solidification conditions. Admittedly, this source of driving force is a unique one and has served well in numerous experiments. However, although the striation substructure provides a thermally stable driving force, the subject of its reproducibility from crystal to crystal is questionable. In fact, Aust and Rutter3 attribute the scatter shown in some of their experimental points and several anomalies in boundary migration rates to variations in the substructure driving force along a single specimen. A further limitation on striation-induced driving force is that the driving force cannot be varied over wide ranges in a controlled manner. More often used as a source of driving force is the strain energy stored in a crystal during plastic deformation. This type of driving force has the disadvantage that it is not thermally stable due to recovery taking place simultaneously with the grain boundary mobility measurements. On the other hand, this strain-induced driving force is very reproducible from crystal to crystal since it is very easy to grow single crystals possessing the same purity and crystallographic orientation and then to strain them identically. In order to measure grain boundary migration rates two different methods are primarily used. Most often the technique employed is the heat-cool-etch method1' which involves thermal cycling, while the other technique, developed by Graham and Cahn11 using an X-ray diffractometer and goniometer furnace, involves continuous heating only. Thus the influence of thermal cycling vs continuous heating is a factor to be considered in grain boundary migration rate measurements, particularly in cases where the source of driving force is the strain energy stored in the deformed matrix, and recovery is likely to occur. Numerous recent investigations have shown that extremely small impurity additions to zone-refined metals exert a marked effect on grain boundary migration rates1-5, 9, 12-27 and a few have considered the effect of the distribution of impurities.28-35 The concentration of impurities and their distribution as influenced by heat treatment must also be taken into account in migration-rate studies. In the present article consideration is given to the influence of the magnitude of driving force, recovery, and previous heat treatment on grain boundary migration rates. In order to vary the driving force over a large range it was necessary to use as a source of driving force the energy stored in the matrix crystal during plastic deformation. A majority of the investigations were performed on aluminum specimens which were of such compositions as to exhibit precipitation-hardening behavior.

Jan 1, 1965

By Langtry E. Lynd

The predominant tonnage use of titanium is as a white pigment, in the form of rutile or anatase, which are allotropic modifications of titanium dioxide. Because of its whiteness, high refractive index and resulting light scattering ability, titanium dioxide is unequaled as a white pigment for paints, paper, rubber, and a wide variety of other materials. Consumption of titanium dioxide pigments for these uses has been rising steadily for many years, United States consumption in 1956 amounting to about 486,000 tons, worth $250,000,000. Production was off a little in 1957 and 1958. An outstanding development in the titanium field in recent years is the expansion of titanium metal production. Virtually nonexistent before 1948, United States production of pure titanium metal sponge reached a high in 1957 of about 17,200 tons, worth about $77,000,000. United States titanium sponge metal production in 1958 was cut back to about 4,600 tons because of reductions in military requirements. Another major use of titanium, in the form of the mineral, rutile, is for welding rod coatings. United States consumption of rutile for this purpose in 1958 amounted to about 11,000 tons, worth $1,100,000. Titanium-Bearing Minerals Although several minerals contain titanium as a major constituent, only a few of these occur in sufficient quantities and concentrations to be of commercial importance. These are ilmenite (FeTiO3), rutile (TiO2), and alteration products of ilmenite which have been referred to as weathered ilmenite, leucoxene, or arizonite. The other polymorphs of titanium dioxide, brookite and anatase, occur in a few deposits, of which only one has been of even minor importance. Considerable concentrations of titanite or sphene (CaTiSiO5) and perovskite (CaTiO3) are known, but do not compete with ilmenite and rutile deposits in grade or size. Rutile is very widely distributed as an accessory mineral in most rocks, but large deposits of commercial importance are rare. A few rock deposits have been worked for rutile but only one, in Virginia, is in operation (1959). Development of one in Mexico was discontinued recently. At present, the main sources of rutile are the beach and dune sands of Australia and Florida. A major use of rutile is for the manufacture of titanium tetrachloride, which is the intermediate compound universally used in titanium metal manufacture. Another main use of rutile is for welding rod coatings. Although the whiteness and brightness of titanium dioxide pigment is due to the high refractive index of rutile or anatase, natural rutile is too impure to be used directly as a white pigment, is too expensive to use for manufacturing pure oxide pigment, and is too scarce to provide the required tonnages. Instead, the cheaper, more abundant, mixed oxide of iron and titanium, ilmenite, which is readily decomposed by sulfuric acid, is used for manufacture of rutile and anatase pigments. Ilmenite is mined from both rock and sand deposits. Rock deposits contain ilmenite in massive or heavily disseminated form along with magnetite or hematite and are almost invariably associated with anorthositic and gabbroic rocks. Ilmenite also occurs as an accessory mineral in a great many igneous and metamorphic rock types. Concentrations of

Jan 1, 1960

By B. L. Landrum, P. B. Crawford

The rise of a new laboratory model for studying tran-sient fluid flow problems, is described. The theory of he model is based on the analogy between the equa-ions which describe the flow of compressible fluids in porous media and the conduction of heal m solids. The "thermal model" is used to study the Iransient Pressure distributions during fluid displacement in five Standard well patterns. The studies indicate quantita-ively how die pressures change with lane at any poit in the reservoir. It was found that, in general, the equipressure contours are more radial about the wells early in the program than after steady-state conditions are established. In addition two studies of fractured five-spot patterns are presented to illustrate the opplicability of the model for a wide range of reservoir conditions. INTRODUCTION In reviewing the oil recovery techniques involving fluid displacement it was found that a very considerable quantity, if not all of the fluid within the pattern, mav be displaced (during a time-dependent or transient period rather than the usually applied steady-state conditions. Since the oil is displaced during a transient period, it was believed desirable to study the nature of the transients for several of the commonly used fluid displacement patterns. A literature review indicated fairly complete studies of the streamlines and isopotentials for steady-state: yet few data were available on the transient displacement process. Several simulated steady-state multiwell displacement programs were carefully mapped by Foster and Lodge on an electrical conducting sheet as early as 1875, hut the more recent work of Muskat provides the best source for steady-state phenomena having direct petroleum production applications. In order to study the transient phenomena a new lab-oratory model was developed which is based on the similarity of the equations that describe the flow of fluids and the conduction of heal. The equations describing heat flow were developed early in the nineteenth century. Regorous solutions tor most transient problems are in gcneral complex and usually limited to fairly restricted houndary conditions.2 the thermal model may be used to obtain approximate solutions for many transient problems without some of the restrictions required for analytical solution. The application of the analogy between heat conduc-. tion in solids. electrical flow and fluid flow, in a porous media has long been recognised. Techniques originally developed for the solution of heat conduction prol?lems have in many instances proved useful in ohtaining solutions to fluid flow prohlcms. Ir is not surpri5ing then that a heat conduction or thermal model might bf usefull in sludying transient fluid flow. As an example ol the problems suitable for the study with the thermal model, transient pressure distributions during fluid displacement programs are studied for the five-spot, line-drive, staggered line-diibe. seven-spot 211 two fractured patterns. A model was constructed of an iron plate of geometry similar to the reservoir patterns under study. The principle of mirror images as suggested by Bryan was employed in shaping the model. A temperature differential was obtained by soldering two sections of copper tubing to the plate at points analogous to the well location in the field. Hot and cold water was passed through the tubing. The temperature distribution, analogous to the pressure distribution in the field. was obtained a a function of time from thermocouplcs distributed over the plate.

By C. C. Mattax, J. E. Bobek, M. O. Denekas

ABSTRACT investigations in recent years have shown that rock wettability can exert a profound influence on the displacement of oil by water from oil producing reservoirs. Core analyses frequently show oil recoveries from preferentially water-wet rock to be significantly greater than those from preferentially oil-wet rock. Thus, an accurate prediction of water-drive or waterflood oil recovery is dependent on the evaluation of reservoir rock wettability. Laboratory and field studies have been undertaken to examine and develop methods which may be used to measure rock wettahililiy, to investigate factors which may alter the wettability of reservoir rock, and to determine the wettability of specific reservoirs. It has been found that measurement of the rate and volume of spontaneous imbibition of the wet-ting phase by a rock is a reliable and reproducible test for semi-quantitarive determination of preferential rock wettability. Laboratory tests have shown that the wettability of reservoir rock may depend on both the crude oil composition and the rock type. Field and laboratory tests have indicated that coring flulids and core handling techniques can cause significant changes in the wettability of rock surfaces. However, a few fluids, brine in particular, appear not to affect core wettability and may be used when coring to determine reservoir wettability. Core handling and packing procedures have been developed which preserve core wettability during storage and laboratory testing. The wetfability characteristics of six reservoirs have been evaluated by wettabilify tests performed in the field on fresh cores cut with brine or special water-base muds. The tests indicated that all six reservoirs are water wet; however, the de-gree differed from one reservoir to another. INTRODUCTION Although surface properties of reservoir rock and interfacial characteristics of rock, crude oil, and water systems have been discussed for many years, the full significance of these properties to the production of oil is still in the process of evaluation. It is known, however, that one surface characteristic—preferential wettability of the reservoir rock—-is of paramount importance when the reservoir is being produced by water-flood or water-drive mechanisms. The importance of rock wettability has been pointed out by several authors'.',%* who have found that pref- erentially water-wet cores flood more efficiently than oil-wet cores; that is, more oil is recovered from water-wet cores in the early flooding stages than from oil-wet cores. Other authors'," indicate that waterflood oil recovery from cores of intermediate wettability may be greater than that from either strongly water-wet or strongly oil-wet cores. These recent investigations emphasize that the true wettability of a reservoir must be known before the performance of waterflood or water-drive reservoirs can be accurately evaluated. When reservoir wettability is to be determined by core analysis, precautions must be taken to maintain the original wettability which can be altered readily during coring5 nd testing.' In the coring operation the core may be partially or completely penetrated by the drilling fluid which, if it contains surface active materials, may drastically change the wettability of the core. Also, improper core handling during stcrage and testing may change its wettability because of evaporation of fluids or exposure to oxygen or surface active contaminants. One purpose of this paper is to discuss methods for obtaining, preserving, and testing cores without altering their original wettability. In addition, the results of wettability tests on fresh and preserved cores from six reservoirs are presented where special precautions were taken to obtain samples without altering their wettability during the coring operation.

By R. E. Miner, J. K. Jackson, D. F. Gibbons

Internal-friction measurements were made during isothermal aging treatments of 18 pct Ni maraging-steel wires between 420° and 612°C. A sharp initial drop in the internal-friction level was interpreted in terms of a rapid dislocation recovery reaction. The rate of the recovery was found to be independent of temperature. Truncation of the recovery reaction was apparent in those systems that exhibited the rapid age-hardening characteristics of the maraging steels. It is proposed that this initial hardening response is the result of a low activation energy preprecipitation reaction involving molybdenum. A gradual rise in the internal-friction level at longer aging times was associated with the precipitation of a molybdenum-containing precipitate. CONSIDERABLE research effort has recently been devoted to the mechanisms responsible for the high strength and toughness of 18 pct Ni maraging steels. These bcc martensitic alloys are found to harden during aging at temperatures between 400° and 600°C. The aging response is very rapid with more than half the total hardness increase occurring within the first few minutes of aging, Fig. 1. Precipitate particles have been observed in the later stages of aging by a number of investigators.'-' While the identity of the precipitates remains the subject of some controversy, one or more of the intermetallic compounds, Ni3Mo, Ni3Ti, and Fe2Mo, are almost certainly involved. Heterogeneous nucleation of precipitates at dislocations has been noted8 and cobalt is believed to enhance the formation of fine, homogeneously distributed particles by lowering the solubility of the alloying elements in the martensitic matrix.3,7 Transmission electron microscopy studies of the initial hardening behavior have not been fruitful. Strengthening mechanisms based on atomic ordering have not been generally supported by X-ray and neutron-diffraction experiments.9 In the present investigation, the aging reaction was studied using isothermal-aging internal-friction measurements. The marked sensitivity of internal friction to short-range diffusion and precipitation processes has provided a convenient tool for the elucidation of the strengthening mechanisms operative in the maraging steels. EXPERIMENTAL PROCEDURE An upright torsion pendulum was used to measure the internal friction of several maraging steels during isothermal aging. The pendulum was placed in an atmosphere of helium at a pressure slightly less than atmospheric. To permit measurement of internal friction during the first minutes of aging, the specimens were rapidly heated by passing a current through them in a manner similar to that described by Ang and Wert.10 Thermal gradients in the specimen were largely eliminated by using specially designed specimen grips11 which produced temperature variations of less than 1 pct over 90 pct of the specimen length and less than 3 pct over the entire length at aging temperatures up to 620°C. A proportioning strip-chart program controller was employed to maintain constant specimen temperature during treatments of up to 36 hr duration. A number of vacuum-melted laboratory heats having compositions near that of a typical commercial 18Ni-7Co-5Mo-0.4Ti alloy were investigated. The amount of cobalt was varied from 0 to 7 wt pct in five of the heats. Either molybdenum or titanium was omitted in the remaining two heats. The alloy desig-

Jan 1, 1967

By N. F. Schulz, H. A. Lex, J. D. Zetterstrom

A green ball of iron ore faces many perils from the time it is formed until it finally emerges from the pelletizing furnace as a hardened pellet. For instance, if the rate of heat transfer into a ball is sufficient to produce vapor from either the free or combined water more rapidly than it can escape at a tolerable pressure, the ball may split, spall, or even explode, a failure commonly known as decrepitation. To avoid such failures, one must either limit the rate of heat transfer during the drying and preheating stages, at the expense of production rates, or improve the decrepitation resistance of the green balls. The latter remedy may often be accomplished through changes in ore preparation, balling procedures, or the judicious use of binders or other additives. INTRODUCTION Pelletization has become established as an especially desirable method for the agglomeration of fine taconite concentrates and it promises to be equally satisfactory for improving the physical structures of certain natural ores. A high-quality pelletized iron ore consists of uniformly sized spheres, usually about 1/2-in. diam, which are strong enough to resist abrasion and breakage during handling and which reduce well without disintegration in the blast furnace. The unfired agglomerates, "green balls", are subject to several destructive effects that must be avoided or minimized if a high-quality product is to be obtained by pelletization. Among these are abrasion and impact deformation or breakage during handling of the wet green balls, deformation and breakage by compressive forces in the bed of ore in the pel-letizing furnace, decrepitation during drying and preheating, wind erosion, and radial cracking at firing temperatures. Moisture condensation from the warm saturated gases downstream from the drying zone on wet, cool balls may cause bed collapse if it becomes excessive. Decrepitation is defined as the sudden disintegration of green balls, usually with an audible pop, that occurs when they are heated too rapidly during the drying or preheating stages of the pelletization process. The extent of ball disintegration may vary from merely splitting off a small fragment to almost total disintegration into the original ore particles making up the ball. Such ball destruction results in a decreased yield of pellets, and the fragments, which also tend to interfere by obstructing the gas flow through the bed, must eventually be screened from the fired product and recycled. The closely related type of ball failure that sometimes occurs during the high temperature firing stage, resulting in radial cracks without fragmentation, was not considered to be decrepitation for the purpose of this investigation. Failure by decrepitation is not usually a serious problem in the pelletization of taconite concentrates. The problem is significant, however, in the pelletization of some natural ores, especially those containing hydrous iron oxides. In some instances, economicd production rates cannot be maintained if the drying and preheating rates are slowed down enough to avoid decrepitation. OBJECTIVES This investigation was undertaken to: (1) Develop a practical laboratory means for quantitatively measuring the tendency for green balls to decrepitate in iron ore pelletizing furnaces, and (2) Investigate the causes and cures of ball decrepitation. MATERIALS Two iron ores were used in the work reported here: a taconite concentrate at 90% minus 325 mesh, containing 65.0% Fe, 8.4% SiO2, and no loss-on-ignition; and a crude oxidized ore at 54% minus 325 mesh, containing 59.1% Fe, 3.6% SiO2, 1.1% A12O3, and 9.5% loss-on-ignition. For a special test of effect of particle size distribution on decrepitation, two other

Jan 1, 1967

By A. W. Bethune, L. M. Pidgeon

The equilibrium vapor pressure of zinc has been determined over the systems: ZnS(s) + Fe(s) = FeS(s) + Zn (vapor) and ZnS(s) + 2Cu(s) = Cu2S(s) + Zn (vapor) by reacting the components in an evacuated tube containing a thin copper fiber, and allowing equilibrium to be established with respect to the brass formed and the zinc in the vapor phase. The composition of the brass formed was determined and equilibrium vapor pressure values obtained from existing data. Between 850' and 1000°C, values for the first reaction ranged from 8 to 58 mm Hg; for the second reaction from 1.8 to 22 mm Hg. THE direct reduction of metallic sulphides may be indicated by an equation of the form MS + X = XS + M [1] where X is some suitable reducing agent. In the case where M is a metal of relatively high volatility, the use of vacuum will displace the equilibrium to the right at comparatively low temperatures in the face of the usually unfavorable thermochemistry. For this technique to be feasible, MS, X, and XS, must of course be nonvolatile compared to M. In this regard, zinc becomes an obvious metal both from the point of view of its volatility and the fact that most commercial ore deposits of this metal occur as the sulphide, and its direct reduction would avoid the expensive roasting process necessary prior to present day reduction methods. Two reducing agents are of interest, namely copper and iron, with the former having the added attraction of being relatively easily regenerated by oxidation in the copper converter. The possibility of these reactions has been considered before. Imbert1 patented a process whereby zinc sulphide was reduced by either copper or iron. The process as described took place at atmospheric pressure and, at the high temperatures required, the system was molten, resulting in the formation of a matte with the consequent reduction in the activities of the reactants. Peterson2 did further experimental work on these reactions and, although promising results were obtained on a small scale, attempts to increase the size of the furnace led to excessive "blue powder" formation. The early workers failed to realize the large reduction in temperature afforded by the use of vacuum and its desirable results. More recently, the direct reduction of zinc sulphide by iron has been the subject of a thermody-namic investigation by Kelley,3 and Gross and War-rington' have studied the kinetics of the reaction in the temperature range 900" to 1000°C, their experiments being conducted using vacuum and indicating that the reaction would proceed practically to completion in 1 to 3 hr, depending on the temperature. A qualitative examination of the system ZnS-Cu carried out at this University indicated that 98 pct of the theoretical zinc in the charge could be recovered in 1 hr at 1000°C when operating under reduced pressure. The purpose of this research program was to study the equilibrium of the two reactions. During the investigation, reference to the experimental work of Schenk5 was found but, due to lack of detail in the report, it was felt that it would be desirable to continue the equilibrium measurements. Selection of Method The measurement of vapor pressure of metals presents obvious problems resulting from the high temperatures which must be employed. In the present case, the production of the "reaction pressure" introduces a further difficulty since a chemical reaction must proceed before any metal vapor pressure is produced, resulting in depletion of the re-

Jan 1, 1954

By C. R. Clark, G. Swift, D. S. Roberts

The purpose of this investigation was to measure PVT behavior of various types and combinations of heavy hydrocarbon components from the paraffinic, naphthenic and aromatic classes where the relative proportions Of the various components were selected to approximate those of natural gas or gas condensate systems. Synthetic mixtures were used so that the compositions Of the various components could be measured accurately. n-Heptane, methylcyclohexane and methylbenzene were used to represent the paraffinic, naphthenic and aromatic components of the heavy fraction. In the mixtures studied, the heavy fraction composition was held constant at O. O5-mole lraction, the balance being methane except for one mixture where 0.10-mo1e fraction of an intermediate component, propane, was added. The PVT data for the mixtures were determined in a variable-volume, constant-mass apparatus at psuedo-reducedtemperatures from 1.84 to 2.00, over a pseudo-reduced pressure range from 2.3 to 12.0. The experimental results showed that, regardless of the type of heavy material (paraffinic, naphthenic, aromatic, or combinations thereof) mixed with methane or methane and propane, the compressibility factors at equal values of pseudo-reduced temperature and pressure varied by less than 2.2 percent. INTRODUCTION PVT data is used for natural gas and gas condensate fluids in determining reserves of reservoirs and performance of wells, in metering produced fluids, and in recombining samples for laboratory studies. While there are vast amounts of PVT data reported for natural gas and gas condensate systems from which useful correlations have been developed, ' the compositional analyses for these systems and the resultant correlations typically were made with components analyzed through some arbitrary carbon number, usually C6, with the residue reported as a lumped "heavy" fraction. The heavy fraction was stoichiometrically recombined on the basis of an apparent molecular weight to give the final compositional analysis. It is virtually impossible to make a systematic analysis of the effect that variation of the relative amounts of paraffinic, naphthenic and aromatic constituents of the heavy fraction of natural systems might have on PVT behavior. Because there is considerable latitude in the relative amounts of these constituents, one speaks of crudes or condensate liquids as being "paraffin base", etc. It is of interest to determine if changes in the relative amounts of these three types of hydrocarbons in the heavy fraction cause significant changes in PVT behavior. If so, steps should be taken to describe better the nature of the heavy fraction in PVT correlations. If not, more confidence can be placed in the correlations presently employed. DESIGN OF THE EXPERIMENTAL INVESTIGATION We attempted to determine if changes in the base of the heavy fraction would cause significant changes in the PVT behavior of gas or gas condensate fluids. Synthetic mixtures were used to enable us to systematically vary the base of the heavy fraction and to analyze accurately the fluids. We found that the heavy fraction of naturally occurring condensate systems seldom exceeds 0.05-mole fraction. Thus, the mole fraction of the heavy fraction in the synthetic systems studied was set arbitrarily at 0.05, to maximize whatever deviations in PVT behavior that might occur. Further, we judged that since the C7 hydrocarbons normally are present in greater quantities than higher carbon number hydrocarbons in naturally occurring systems, the use of n-heptane, methyl cyclohexane, and methylbenzene to represent the paraffinic, naphthenic, and aromatic species in the heavy fraction would be most appropriate. Finally, to enable us to compare our

Jan 1, 1970

By Robert B. Hoy

If the reader finds that the basic information in a commodity chapter is insufficient, he can consult the appropriate sources in this chapter to find more detailed or more up-to-date information. In these days, technology develops so rapidly that this 5th edition will be somewhat out of date even by the time it is distributed. A comparison of this edition with the 4th edition (1975) of Industrial Minerals and Rocks will clearly demonstate how rapidly the scene changes. One of the best sources of new information, of course, is attendance at technical meetings. For example, the papers presented at the national and sectional meetings of AIME usually discuss new developments in the respective divisions of the society. Frequently this information is available in Preprints. In addition some are printed in Mining Engineering and/or the Transactions of the Society of Mining Engineers of AIME. Furthermore, other professional and trade journals contain articles pertinent to the field. A journal introduced in 1967, Industrial Minerals, published by the Metal Bulletin, Ltd., London, is an excellent source of information. The Mining Journal, Ltd., also in London, publishes a weekly journal, a Mining Magazine (monthly), and a Mining Annual Review. The latter covers the field from three aspects: (1) by commodities, (2) through technical developments, and (3) geographically. The Industrial Minerals Directory 1977, 1st ed., Metal Bulletin Books, Ltd., London, provides addresses of organizations in the field. Other useful magazines and periodicals include Engineering and Mining Journal, Pit and Quarry, Rock Products, and World Mining, all published in the United States. In addition many new books related to industrial minerals have been published since the 4th edition of Industrial Minerals and Rocks. Most of these are included in the bibliography of each chapter in this volume. Another excellent information source is the proceedings of the Forum on Geology of Industrial Minerals. This group, which held its 18th annual meeting in 1982, is sponsored by a state geological survey or another mineral agency on a rotational basis. The proceedings have been published by the various sponsors and are available as indicated in Table 1. Two major sources of basic industrial mineral and rock data in the United States, and also a good source for many foreign countries, are the US Geological Survey and the US Bureau of Mines. The two agencies publish many reports and maps on a variety of geological and mining subjects. In addition, each agency has an indexed list of all their publications with a free service announcing new publications: New Publications of the Geological Survey, US Geological Survey, 329 National Center, Reston, VA 22092 and New Publications-Bureau of Mines, Publications Distribution Branch, US Bureau of Mines, 4800 Forbes Ave., Pittsburgh, PA 15213. The US Bureau of Mines (USBM) publishes annually Minerals Yearbooks which provide statistical data on mineral products including production, consumption, imports and exports, as well as information on new developments. Another very useful USBM series is called Mineral Facts and Problems. Editions were published in 1960, 1965, 1970, and 1975. Four major series of publications by the Bureau are Information Circulars, Reports of Investigations, Mineral Trade Notes, and Minerals and Materials. The last two are particularly good for news of foreign developments. The Bureau of Mines Employee Directory, available at all USBM offices, lists addresses and telephone numbers for all offices as well as same for all commodity and area specialists.

Jan 1, 1983

By Lincoln F. Elkins

The Spraberry Trend Field of West Texas was discovered in January, 1949. Drilling of 2.234 wells and production of some 45 million bbl of oil by January, 1953, indicated this to be an important field which will ultimately cover more than 400,000 acres. In addition to being the world's largest field in areal extent, the Spraberry has presented many problems in well completion and operation and has demonstrated unique reservoir performance characteristics. The pay section consists primarily of a few fine grained sandstone or siltstone members in a thousand-ft thick section of shale, limestone. and siltstone. Since porosity averages only 10 per cent and nearly all permeabilities are less than 1 md, conventional core analysis does not delineate the "pay" section. Mercury injection was used as a capillary pressure test adaptable to rapid routine use to select those intervals having low enough connate water saturation to contain commercially significant oil saturation. In the central area of the field this "pay" amounts to 16 ft of Upper Spraberry and 15 ft of Lower Spraberry sands. An interconnected system of vertical fractures, observed in cores, provides the flow channels for oil to drain into the wells hut most of the oil is stored in the matrix since the void volume of fractures is estimated to be less than 1 per cent of that in the sand. Initial potentials of wells range up to 1.000 B/D after fracture treatment which should be compared with estimated capacity of 5 to 10 B/D if oil had to flow into the wells through the sand itself. Without exception initial pressures of later drilled wells were significantly lower than initial pressures of earlier drilled nearby wells in a large area some 6 miles long. This means the earlier drilled wells had drained fluids from areas much greater than their 40-acre proration units. Since most of this performance occurred while the reservoir pressure was above the. saturation pressure it was analyzed by the compressible fluid flow theory. This analysis gave calculated initial presrilres which agreed within 30 psi of measured pressures of 60 per cent of wells in the area using 16-md permeabilitv corresponding to a fracture system substantially that indicated by cores and using combined compressibility of rock and its contained oil and water corresponding to the core analysis data. The most important feature of this analysis was the very close agreement between effective compressibility of the rock and its contained oil and water from the field performance and that from the core tests, because it meant there are no "islands" of low permeability reservoir rock left untapped in the inter-well area and thus no additional wells are necessary to insure that at least one well penetrates each "reservoir." Twenty-five of forty-four 40-acre spaced wells on three contiguous sections were wed in a four-month inteference test. Six shut-in well. were tested monthly for oil production. productivity index. gas-oil ratio and pressure buildup, and seven shut-in wells were tested for decline in reservoir pressure. Tests on 12 regularly producing wells gave comparative data for interpretation of shut-in test wells. Reduction in reservoir pressure, decline in productivity index. and increase in gas-oil ratio were found to be substantially the same in the shut-in test wells as those in the comparative regularly producing wells, meaning that the producing wells were depleting the

Jan 1, 1953

By O. N. Carlson, W. M. Paulson

A phase diagram is proposed for the Y-C system based on the vesults of thermal analyses, microscopic obsevvations, and X-ray diffraction studies. Three intermediate phases occur in the system: a congru-ently melting fcc phase with a wide range of homogeneity about the composition Y2C, an intermediate solid-solution region between 55 and 58 at. pct C, and a bct dicarbide melting congruently at 2415°C. All three compounds undergo a phase transformation at elezlated temperatures. A continuous serzes of solzd solutions exists between the fcc phase and the high-temperature form of YC2 with a maximum in the solidus at 2000°C and 30 at. pct C and a minimum at 1805°C and 54 at. pct C. THIS investigation of the Y-C system was undertaken as part of a nuclear materials development program. Yttrium-base alloys are of interest as possible containers for liquid metals, and carbides are currently receiving increased attention as high-temperature materials for advanced reactors and other applications. Previous work on this system was limited in scope, and the results were somewhat inconclusive and at times contradictory. Spedding et al.&apos; reported the existence of a triyttrium carbide having an fcc structure with a wide range of homogeneity and Dean et a1.2 reported the existence of a rhombohedra1 phase having the stoichiometry of Y2C. Bachella et a1.3 observed that the latter was the result of ordering of carbon atoms in the fcc solid solution. The ordering range was placed at 800" to 1000°C. Vickery et a1.4 reported a high-melting compound which they identified as yttrium dicarbide, and Spedding and coworkers1 determined the structure of this phase as bct with lattice parameters a = 3.66 and c = 6.17A. Samsonov et al.5 reported the melting point of YC2 as 2300" * 50°C. Recently Bowman et a1.6 found a transformation in the dicarbide from the tetragonal to an fcc form at 1320 20°C. Samsonov and coworkers7 reported a monocarbide of yttrium melting at 1950" * 20°C and also a sesqui-carbide melting at 1800" * 50°C. The existence of the latter has also been indicated by others,1&apos;8 but neither compound has been definitely established. The Y-C phase diagram shown in Fig. 1 was proposed by Chubb and Keller8 in 1964 based on the data available at that time. The tentative nature of this diagram together with the uncertain status of the compounds indicated that additional work on this system was needed. EXPERIMENTAL PROCEDURE Yttrium metal of 99.9 pct purity was prepared for use in this study by the reduction of YCl, with calcium to form a sponge product.9 The major impurities in this material were as follows: 100 ppm C, 150 pprn H, 20 ppm N, 300 to 1000 ppm O, <20 ppm Ca, <100 ppm Cr, <80 ppm Cu, 150 ppm Fe, <30 pprn Mg, <400 ppm Ta, and <100 ppm Ti. Alloys were prepared by arc melting yttrium sponge together with pieces of high-purity graphite rod in a purified argon atmosphere. Homogeneity was insured by repeated melting, inverting the ingot between melts.

Jan 1, 1969

By James E. Lawver, James L. Wright

This paper describes the design of a cell used to measure the electrical conductivity, or the reciprocal resistivity, of granular materials. It also establishes a quantitative relationship between the electrical conductivity and the electrical separation of selected mineral samples. It is estimated&apos; that the free world produces about 13 million tons of mineral concentrates a year by electrostatic or electrodynamic methods. At least 95% of these concentrates are produced by corona discharge type machines that separate minerals by exploiting the differences in their electrical conductivity. But, what is meant by the electrical conductivity of a mineral? How large a difference in the electrical conductivity of two mineral species is necessary to effect a separation? Just what is the role of conductivity in electrical separations with regard to capacity and selectivity? There is a considerable amount of information in the literature on both the mechanisms of conduction and the values of the electrical conductivity of pure single-crystal mineral specimens. In addition, some insight into the role of mineral conductivity can be obtained by referring to a Bureau of Mines publication&apos; in which 95 minerals have been grouped as conductors or insulators as a function of temperature. The classification was made on the basis of the percent of weight that reported as "conductors" in an electrical separator. But, as is often the case in the mineral industry, practical application leads theory — and there is little useful information in the literature giving any kind of quantitative relationship between electrical conductivity and electrical separations. The problem is a bit complex because electrical conductivity per se — which can be rather easily measured on large, single grains — is not sufficiently informative to permit quantitative predictions of the separability of the mineral system. Practical "high-tension"* separations are made at such feed rates that the band of minerals on the rotor is multilayered in thickness. Thus, the effective conductivities of minerals as seen by a high-tension machine include particle-to-particle contact resistance, which is often a controlling factor in making a separation. This is particularly true when the mineral grains are coated with slime or with a dielectric surface film. From a high-tension separation viewpoint, one is actually concerned with the time required for corona-charged grains to lose enough charge so that the centrifugal force acting on the particles exceeds the image force holding the grains to the rotor. This calculation requires a knowledge of the effective mineral conductivity s. (The conductivity of the metal rotor is sufficiently greater than that of the minerals so that it need not be considered in charge decay calculations.) The charge density at time t can be approximated by the relaxation equation.3 where t 5 charge density at time t r, - charge density when t = 0 cr e total electrical conductivity £ = permittivity The time required for the charge density to fall to l/e of its initial value is called the relaxation time and is numerically equal to €/n. AS defined here, u is the conductivity of an element of homogeneous grains making contact with each other and with a grounded rotor. This paper deals with the design of a conductivity cell used to measure a, or its reciprocal p, the electrical resistivity. CELL DESIGN Initial test work was performed with a cell recommended by ASTM.4 Since the reproducibility with the ASTM cell was not satisfactory, it was decided to

Jan 1, 1970

By C. K. Eilerts

Finite difference equations were programmed and used to integrate the second-order, second-degree, partial differential equation with variable coefficients that represents the transient linear flow of gas-condensate fluids. Effect was given to the change with pressure of the compressibility factor, the viscosity, and the effective permeability and to change of the absolute permeability with distance. Integrations used as illustrations include recovery of fluid from a reservoir at a constant production rate followed by recovery at a declining rate calculated to maintain a constant pressure at the producing boundary. The time required to attain such a limiting pressure and the fraction of the reserve recovered in that time vary markedly with properties of the fluid represented by the coefficients. Fluid also is returned to the reservoir at a constant rate, until initial formation pressure is attained at the input boundary, and then at a calculated rate that will maintain but not exceed the limiting pressure. The computing programs were used to calculate the results that would be obtained in a series of back-pressure tests made at selected intervals of reservoir depletion. If effect is given to the variations in properties of the fluid that actually occur, then a series of back- pressure curves — one for each stage of reserve depletion — is required to indicate open-flow capacity and related flow characteristics dependably. The isochronal performnce method for determining flow characteristics of a well was simulated by computation. INTRODUCTION The back-pressure test procedurel is based on a derivation of the equation for steady-state radial flow of a gas, the properties of which are of necessity assumed to remain unchanged in applying the test results. The properties of most natural gases being recovered from reservoirs change as the reserve is depleted and pressures decline, and the results of an early back-pressure test may not be dependable for estimating the future delivery capacity of a well. The compressibility factor of a fluid under an initial pressure of 10,000 psia can change 45 per cent and the viscosity can change 70 per cent during the productive life of the reservoir. There are indications that the effective permeability to the flowing fluid can become 50 per cent of the original absolute permeability before enough liquid collects in the structure about a well as pressure declines to permit flow of liquid into the well. The advent of programmed electronic computing made practicable the integration of nonlinear, second-order, partial differentia1 equations2.3 pertaining to flow in reservoirs. Aronofsky and Porter4 represented the compressibility factor and the viscosity by a linear relationship, and integrated the equation for radial flow of gas for pressures up to 1,200 psi. Bruce, Peaceman, Rachford and Rice5 integrated the partial differential equations for both linear and radial unsteady-state flow of ideal gas in porous media. Their published results were a substantial guide in this study of integration of the partial differential equation of linear flow with coefficients of the equation variable. The computing program was developed to treat effective permeability as being both distance-dependent and pressure-dependent. In this study all examples of effective permeability are assumptions designed primarily to aid in developing programs for giving effect to this and other variable coefficients. The accumulation of data for expressing the pressure dependency of the effective permeability is the objective of a concurrent investigation. FUNDAMENTAL DIFFERENTIAL EQUATIONS DIFFERENTIAL EQUATION OF FLOW Linear transient fluid flow is represented by the partial differential equation,

Jan 1, 1965

By C. G. Dunn, F. W. Daniels

IN recent publications1-5 the existence and behavior of subgrain boundaries in high-purity metals has been clearly brought to light. Lacombe and Beaujardl by means of special etching methods disclosed in polycrystalline sheets of aluminum the existence of substructures differing in orientation by small amounts (about 1/4"). Boundaries of these structures at relatively high temperatures had the remarkable property&apos; of moving about while the ordinary boundaries remained stationary. Cahn2 also observed substructures in bent and annealed single crystals of aluminum, zinc, magnesium, and rock salt. The position of subboundaries could be explained in terms of a dislocation mechanism of polygonization in which dislocations move into lines at right angles to the bent glide planes thereby relieving elastic stresses in these planes. Guinier and Tennevin8,6 disclosed the further interesting feature that polygonized structures coarsened significantly upon prolonged annealing. Somewhat similar subgrain phenomena have been observed in silicon iron of commercial purity. Although some evidence for the development of macro-mosaic structures in silicon iron already has been reported by one of the authors6,7 under the phenom-enological term "crystal recovery," much better evidence recently has been obtained due to improved etching techniques. In addition, phenomena regarding structural changes have been uncovered. The present investigation is divided into three parts: (1) The phenomenon of Laue spot sharpening on annealing cold-rolled crystals, (2) the phenomena of polygonization and subgrain coarsening The material used in the present investigation was high-grade commercial silicon iron sheet of nominal composition, 3.3 pct Si, 0.004 C, 0.011 P, 0.010 S, 0.04 Mn, 0.01 Al, 0.04 Cu, 0.01 Sn. Large single crystals of this material Were prepared for cold-rolling or bending as scheduled. Cold-rolling of 12 pct was carried out on a laboratory 8-in, diam rolling mill. The bending deformations were performed by pressing the crystals between a solid Fig. 2—lllustrative foue patterns to show Laue spot sharpening. a (Left)—Specimen as cold rolled, b (right)—After 48 hr at 1400°C. round bar and a mating half cylinder, both heavily greased. Individual specimens were cut from the deformed crystals, and the cut edges were deeply etched prior to annealing. Laue photographs were made using 40-kv tungsten radiation. The technique used to disclose the various subboundaries was an electropolish and electroetch in a bath of chrome-acetic acid.&apos; The anodic polishing done at 22 v was immediately followed by etching at a reduced voltage, which was dependent upon the nature of the subboundaries. Phenomenon of Laue Spot Sharpening on Annealing Cold-Rolled Crystals Fig. 1 gives the initial and final orientations of the specimens cold-rolled 12 pct. Each specimen was annealed at a temperature and for a time which caused significant structural changes as evidenced by alterations in Laue patterns. Representative Laue patterns and micrographs showing the essential changes are given in Figs. 2, 3, and 4. The essential points to be derived from these illustrations follow: 1. Annealing at 950°C clearly develops a substructure with the orientation of the cold-rolled specimen. 2. The subboundaries formed obviously separate regions of nearly the same orientation. Some of the subboundaries appear as a sequence of dots similar to those observed in aluminum by Lacombe and Beaujard,&apos; but whether this is due to extremely small differences in orientation is not known at present. 3. The substructure coarsens upon prolonged annealing. 4. Prolonged annealing also causes a decrease in orientation spread according to Laue spot sharpening&apos;

Jan 1, 1952

By Oscar Johnson

The industry has been canvassed for information on methods of handling grinding steel at milling plants, an important subject overlooked in most descriptive articles on milling plant arrangements. The data collected are offered in this paper as a guide to designers and planners who have loading and storage problems to solve. WITH capacities of milling plants expanding from a few hundred tons per day to many thousand, replenishment of grinding media is an important phase of mill operation. Information on this aspect of milling procedure, solicited from several mining companies, is summarized here. At International Nickel&apos;s Copper Cliff concentrator the normally strenuous job of changing rods is considerably simplified by the use of the Garrow rod charging machine, Fig. 1. The overhead crane, Fig. 2, brings a bundle of rods, weighing four to a ton, to the loading platform of the machine, positioned in front of the mill. The rods roll one by one down the slight incline of the platform onto a conveyor which sends them into the mill. A modified version of the Garrow machine, Fig. 3, is used at the Federal mill of St. Joseph Lead Co. An overhead crane places the portable steel structure in position in front of the discharge end of any one of the five 9x12-ft rod mills. It then raises a bundle of about twenty 3-in. rods to the discharge platform of the charging machine. The rods are 11 ft 7 in. long and weigh about 278 lb. By tripping a lever the operator allows one rod at a time to roll onto the inclined rollers. A slight push by the operator sends the rod smoothly into the mill. The Union Miniére du Haut Katanga rod charging machine, Fig. 4, is mounted on a pair of wheels at the forward end with swiveling castors at the back for steering it to position for use or storage. Wheels are equipped with locking brakes to maintain the machine in position while it delivers rods to the mill. The device is made in two parts. The first consists of the base, which carries the supporting wheels, grooved rollers, and drive. The other part serves as the rod deck, which can carry up to six 3-in. x 12-ft rods. A short boom built integral with the base reaches through the mill trunnion and delivers the rods into the mill barrel. Three grooved guide rollers ,are provided to receive the rods from the sloping charging deck. One rod at a time is fed to the rollers and thus delivered into the mill. Two of the rollers are driven by 11/2-hp motor through a V-belt drive. The third roller is driven off the first by a single V belt in a groove below the rod groove and on the same center line. Rods are delivered to the charger by an overhead crane in bundles of three to six as needed. The power is supplied by cables plugged into power outlets, suitably located near the rod mill discharge end. The Oliver Iron Mining Co. uses a rod charger, Fig. 5, suspended from a monorail by cables. It is constructed .of structural steel and has two decks, each capable of carrying five rods of 4-in. maximum diameter. The rods ride in grooved free-turning rollers. Legs extending down from the mill end of the mechanism act as supports when the unit is ex-

Jan 1, 1955