Search Documents

By C. H. North, L. E. Lynd, W. W. Anderson, H. Sicurdson

D. R. Grantham (Institute of Mining and Metallurgy, London, England)—This paper is a very valuable contribution to our knowledge of ilmenite and its alteration products. Two aspects are not treated in the paper and further information would be valuable. How far are the alteration processes described influenced by the original composition of the ilmenite? The word gangue is used but it is not clear whether this refers to other chemical constituents in the ilmenite, e.g., magnesia, or to other minerals loose or in composite grains. Has the work described been related to specific gravities? Pure ilmenite is stated to have a specific gravity of 4.79. Some varieties range up to over 5.0, while high magnesic varieties have a specific gravity ranging to below 4.2. Alteration to hematite might lower the specific gravity and a porous texture due to the removal of iron and the formation of rutile might also lower it. As specific gravity is a quick method which often gives an approximate indication of composition, data on the above would be valuable. L. E. Lynd (authors' reply)—Because of the way in which beach sand deposits were formed, it is impossible to tell exactly what the original composition of the parent ilmenites might have been. Information on the influence of original composition on the alteration processes must be derived from other sources, perhaps by comparing the alteration products formed from ilmenite in place in a variety of rock deposits, where parent ilmenite and its alteration product can be recognized. No information of this type has yet been brought to our attention. The material referred to as gangue includes all constituents other than oxides of titanium and iron. Nearly all of this was present as separate grains of garnet, augite, hornblende, quartz, feldspar, spinel, or other gangue minerals. Inclusions of gangue minerals within ore grains were rare, and we believe there is little MgO (1 pct or less) or other impurity actually held in the ilmenite structure in any of the concentrates studied. No specific gravity measurements were made on the samples studied. However, the suggestion that alteration involving loss of iron would lower the specific gravity is a very reasonable one, and is in accord with the findings of Creitz and McVay (Ref. 9 of our paper) who reported two magnetic opaque fractions from Trail Ridge, Fla., to have the following specific gravities and pompositions: The specific gravity of this porous, high TiO² alteration product of ilmenite is closer to that of rutile (4.25) than to that of ilmenite. Due to the porosity, it may even be less dense than rutile, although lower in TiO² and higher in iron.

Jan 1, 1955

By M. A. Westbrook, J. F. Redmond

A method is presented for obtaining porosities of consolidated formations from the drill returns. The method provides a means of determining the bulk volume of a large number of particles, such as drill cuttings, by employing a capillary diaphragm for removal of surplus surface liquid from saturated cuttings having pores of capillary size, which reduces tile amount of error present in former attempts to determine the porosity of drill cuttings. The method makes it possible to obtain a considerable amount of supplementary data on consolidated formations. Introduction Porosity is a direct measure Of the volume of the voids in a formation. It may be used for estimating the permeability of a formation provided that a correlation of these two properties has been obtained from the analysis of cores from the particular formation, and it forms a desirable aid in interpreting electric logs.1 These useful applications have emphasized the importance of developing a method for determining the porosity of the formations penetrated by a well by some means other than coring, for even in exploration wells it is neither economical nor practical to core all formations. Also, in wells where at the outset the coring program appears comprehensive, it is frequently found that, after certain layers are drilled. more complete information is required for evaluation. Porosity values, if obtainable, would be of great assistance in such cases. In soft formations it is usually possible to obtain porosities after drilling with cores taken by side-wall coring devices. In hard consolidated formations, that coring procedure is not alway practicable and other methods for determining porosities must be resorted to. A first choice is the examination of drill cuttings. if an analytical procedure is available that is both accurate and reasonably rapid. Such a procedure has been devised and is applicable to sand and limestone cuttings having pores of capillary size. Although imp,ovements can yet be made, it is believed that the new technique is sufficiently well developed to warrant description, Preparation of Sample The well samples containing the cuttings representative of the particular intervals are first washed through a No' 6 gauge screen. The cuttings remaining on the Screen are large enough to use lor the porosity measurements' From the sized sample, the cuttings to be examined are separated from the shale and Other extraneous particles. It is recommended that 10 to 15 c.c. of the selected cuttings be used for measurements, although only 4 to 5 c c. were used to make the comparative tests described later in this article. These cuttings are extracted and dried by the same methods used for preparing core samples for porosity and other measurements. The separation, which is at present being carried out by hand, is the most tedious

Jan 1, 1946

By George A. Packard

The shaft of the Raven mine, at Butte, Mont., is an incline 1,700 ft. in length and dipping at various angles. At the top the dip is 70" from the horizontal, but this is gradually flattened until at the 300-ft. level the inclination is only 47. This angle continues to the 1,100-ft. level, below which it curves with a 125-ft. radius to 78". In addition to these variations in dip, the shaft does not lie in the same vertical plane, with the result that the hoisting rope not only rubs at intervals on both the hanging and foot walls, but presses strongly against the west dividers near the collar, while 300 ft. below it runs close to the east end plates. The early operators used no idlers, aid wall plates cut 6 in. deep by the rope resulted. Later operators first attempted to overcome the excessive friction, and the wear of rope and wall plates, by introducing solid cast-iron idlers, 3 in. in diameter. To allow for the travel of the rope from side to side some of these had to be 3 ft. long and were very heavy. Judging from the appearance of the old idlers of this type found at the mine, they often failed to turn in the bearings, which is not surprising when it is considered that they would have to make 1,000 rev. a minute under ordinary hoisting conditions. The next rolls were made of wood, 6 in. in diameter, with an iron band about each end, and a pintle of 1-in. round steel driven in at the ends to serve as a shaft. These wore rapidly, and were soon replaced by rolls made from water pipe, 5 or 6 in. in diameter, cut to the desired length and fitted with a wooden cylinder into which the pintle was driven. Where the idlers were used on the hanging wall of the shaft the original bearing was simply a piece of + by 1 3/2 in. strap iron, 10 in. long, turned up at the end in a circle 11/8 in. in diameter to receive the shaft. A small hole served for oiling, and common black oil was generally used, although filtered oil from engine bearings and compressor bearings was also used. When the rolls were to be placed on the foot wall the bearings were made from two pieces of 1 by 3 in. steel, 6 in. long. A half circle was cut on the flat side of each piece and the two half circles together formed a bearing. Oil holes were provided, and in some cases holes were bored through the two pieces so that they could be screwed or spiked to the wall plates.

Jan 1, 1915

By R. R. Knuckey

Having been associated with the operation of the de Vooys process for coal, which has treated 13,000,000 tons per annum, and recognizing the process as of value in ore sorting, Huntington, Heberlein and Co. Ltd. (Great Britain) in 1936 made an examination of all other existing methods. In none of the pioneer applications had recognition been given to the necessity for maintaining certain conditions that are essential for sorting certain ores if a truly efficient separation by gravity alone is to be assured. Consequently, in 1936-1937 Huntington, Heberlein and Co. Ltd., with Pearson, employing certain ideas connected with the de Vooys application, commenced the development of a separator that would allow conformance with optimum conditions in the zone where separation is effected. Later, Holt and Wade added to the value of the original application by Wuensch, Rakowsky and others, whose conceptions are being successfully operated today. Meantime, Trostler had enhanced the value of the original H-H. process by improvements that are now embodied in operating plants, and today the process incorporates an improved apparatus and a stable medium that produce the optimum conditions for separation. These conditions are: 1. Elimination of disturbing currents in the separating zone; 2. Reduction to a minimum of medium-density differences throughout the separating zone; 3. Stable medium of minimum viscosity to permit the unretarded fall of mineralized particles; 4. Removal of products of separation with minimum disturbance to the separating zone. Design of Separator The H-H. sink-and-float separator consists of a pyramidal tank in which the separation actually takes place, connected at the bottom with an inclined bucket elevator. The tank and the elevator are filled with medium to within a few inches of the top of the tank. Medium is fed into the separator at a variety of points, according to the type of ore being treated, and it is withdrawn from the separator at two points: (1) together with the float product, by means of a variable-speed addle, at the surface of the medium, and (2) by flowing over an adjustable weir cut in the side of the elevator casing. The prepared ore is fed onto the surface of the medium. The intermediate paddles, which revolve at a slow speed of 2 to 5 r.p.m., move the floating ore across the bath from feed end to float-discharge end. The ore, which is heavier than the medium, sinks below the sweep of the addles and reaches the boot of the bucket elevator, which discharges it without disturbance of the separating zone. These arrangements for withdrawing medium from the separator allow the use of minimum flows, which connote minimum

Jan 1, 1947

By R. R. Knuckey

Having been associated with the operation of the de Vooys process for coal, which has treated 13,000,000 tons per annum, and recognizing the process as of value in ore sorting, Huntington, Heberlein and Co. Ltd. (Great Britain) in 1936 made an examination of all other existing methods. In none of the pioneer applications had recognition been given to the necessity for maintaining certain conditions that are essential for sorting certain ores if a truly efficient separation by gravity alone is to be assured. Consequently, in 1936-1937 Huntington, Heberlein and Co. Ltd., with Pearson, employing certain ideas connected with the de Vooys application, commenced the development of a separator that would allow conformance with optimum conditions in the zone where separation is effected. Later, Holt and Wade added to the value of the original application by Wuensch, Rakowsky and others, whose conceptions are being successfully operated today. Meantime, Trostler had enhanced the value of the original H-H. process by improvements that are now embodied in operating plants, and today the process incorporates an improved apparatus and a stable medium that produce the optimum conditions for separation. These conditions are: 1. Elimination of disturbing currents in the separating zone; 2. Reduction to a minimum of medium-density differences throughout the separating zone; 3. Stable medium of minimum viscosity to permit the unretarded fall of mineralized particles; 4. Removal of products of separation with minimum disturbance to the separating zone. Design of Separator The H-H. sink-and-float separator consists of a pyramidal tank in which the separation actually takes place, connected at the bottom with an inclined bucket elevator. The tank and the elevator are filled with medium to within a few inches of the top of the tank. Medium is fed into the separator at a variety of points, according to the type of ore being treated, and it is withdrawn from the separator at two points: (1) together with the float product, by means of a variable-speed addle, at the surface of the medium, and (2) by flowing over an adjustable weir cut in the side of the elevator casing. The prepared ore is fed onto the surface of the medium. The intermediate paddles, which revolve at a slow speed of 2 to 5 r.p.m., move the floating ore across the bath from feed end to float-discharge end. The ore, which is heavier than the medium, sinks below the sweep of the addles and reaches the boot of the bucket elevator, which discharges it without disturbance of the separating zone. These arrangements for withdrawing medium from the separator allow the use of minimum flows, which connote minimum

Jan 1, 1947

By M. A. Westbrook, J. F. Redmond

A method is presented for obtaining porosities of consolidated formations from the drill returns. The method provides a means of determining the bulk volume of a large number of particles, such as drill cuttings, by employing a capillary diaphragm for removal of surplus surface liquid from saturated cuttings having pores of capillary size, which reduces tile amount of error present in former attempts to determine the porosity of drill cuttings. The method makes it possible to obtain a considerable amount of supplementary data on consolidated formations. Introduction Porosity is a direct measure Of the volume of the voids in a formation. It may be used for estimating the permeability of a formation provided that a correlation of these two properties has been obtained from the analysis of cores from the particular formation, and it forms a desirable aid in interpreting electric logs.1 These useful applications have emphasized the importance of developing a method for determining the porosity of the formations penetrated by a well by some means other than coring, for even in exploration wells it is neither economical nor practical to core all formations. Also, in wells where at the outset the coring program appears comprehensive, it is frequently found that, after certain layers are drilled. more complete information is required for evaluation. Porosity values, if obtainable, would be of great assistance in such cases. In soft formations it is usually possible to obtain porosities after drilling with cores taken by side-wall coring devices. In hard consolidated formations, that coring procedure is not alway practicable and other methods for determining porosities must be resorted to. A first choice is the examination of drill cuttings. if an analytical procedure is available that is both accurate and reasonably rapid. Such a procedure has been devised and is applicable to sand and limestone cuttings having pores of capillary size. Although imp,ovements can yet be made, it is believed that the new technique is sufficiently well developed to warrant description, Preparation of Sample The well samples containing the cuttings representative of the particular intervals are first washed through a No' 6 gauge screen. The cuttings remaining on the Screen are large enough to use lor the porosity measurements' From the sized sample, the cuttings to be examined are separated from the shale and Other extraneous particles. It is recommended that 10 to 15 c.c. of the selected cuttings be used for measurements, although only 4 to 5 c c. were used to make the comparative tests described later in this article. These cuttings are extracted and dried by the same methods used for preparing core samples for porosity and other measurements. The separation, which is at present being carried out by hand, is the most tedious

Jan 1, 1946

Samuel T. Wellman, Cleveland pioneer steel man, who was often referred to as the "father of the open-hearth process of the United States," died suddenly on July 11, 1919, of heart disease, at Stratton, Me. For more than half a century, he was closely identified with the improvement of equipment used in the making of steel and contributed a number of inventions that virtually revolutionized the industry. Mr. Wellman was born Feb. 5, 1847, at Wareham, Mass., his father at the time being superintendent of the Nashua Iron Co., Nashua, N. H. After attending public school and a year at Norwich University, he served in the Civil War as a corporal of the first New Hampshire Heavy Artillery. He went to Pittsburgh in 1867 and assisted in starting the first crucible steel melting furnace built in America at the works of Anderson, Cook & Co. It melted a ton of steel with an average of 1000 Ib. of nut coal, which cost less than $1, while the melting of a ton of steel in crucibles in the old fashioned coke furnace took three tons of the very best coke, costing from $2 to $3 per ton. This furnace was a great success and in a very few years had driven the coke furnace out of use. From Anderson, Cook & Co., Mr. Wellman went to the Singer, Nimick & Co. works, Pittsburgh, where he built two crucible steel melting furnaces of the same type. After that he spent some time in the office of the Siemens agents in Boston and also at steel works in different parts of the country, starting crucible steel furnaces. He then went to the Bay State Iron Works in South Boston, Mass., where he built the first open-hearth furnace that was a commercial success in the United States. It made steel of a much better quality than had previously been made in this country. The principal use to which it was put in those days was the manufacture of locomotive fire-boxes. From South Boston, he went hack to the old works in New Hampshire where his father was still superintendent, and built for it an open-hearth furnace, a plate mill, and a bar mill. In 1873, Mr. Wellman went to Cleveland to design and build the plant of the Otis Steel Co. He remained with this company for 16 years as engineer and superintendent. During this time he developed the open-hearth charging machine and introduced the electromagnet for handling pig iron and scrap steel. The first charging machine was operated by hydraulic power, and although it was not entirely satisfactory it performed the work fairly well and encouraged its inventor to build another one, which was driven by electric motors. This proved

Jan 1, 1920

By P. Chiotti, G. R. Kilp

IN the study of zinc-zirconium1 and zinc-uranium2 systems, vapor-pressure measurements were made in order to establish the equilibrium phase diagrams for a pressure of 1 atm. In each of these systems, only zinc has an appreciable vapor pressure over the temperature range investigated. The zinc pressure was measured over a sufficiently wide temperature and composition range to permit calculation of the standard free energy, enthalpy, and entropy of formation for the compounds ZrZn, ZrZn2, ZrZn3, ZrZn6, ZrZn14 , and U2Zn17. In these calculations the compounds were treated as line compounds. Although the exact composition range was not determined, metallographic and thermal data indicate that the solubility range for these compounds is small. It is to be noted that the compound initially reported to correspond to the formula UZn9, 2 has been shown by the crystal structure work of Makarov and vinogradov3 to correspond to the formula U2Zn17,. The crystal structure is similar to that for the compounds Th2M17, investigated by Florio,4 et al; here M represents iron, cobalt, or nickel. Therefore, thermodynamic calculations are based on the formpla U2Zn17 EXPERIMENTAL The dew-point method employed to measure the vapor pressure of zinc over uranium-zinc alloys has been described previously.2 The same procedure and apparatus were used in measuring the zinc pressure over zinc-zirconium alloys. In the case of alloys in the two-phase region consisting of a zirconium and the compound ZrZn, the Knudsen effusion method was employed to obtain a few values in the temperature range 600" to 560°C. In most cases, tantalum crucibles were used to contain the zirconium alloys. THERMODYNAMIC PROPERTIES OFU2Zn17 A least-squares treatment of the vapor-pressure data obtained for 35 and 65 wt pct U alloys in the temperature range 650° to 940°C gave lOg10PAtm = 7,713/T + 6.33 Here, as in following equations, T represents degrees kelvin and P represents the zinc vapor pressure in atmospheres. The probable errors for the two constants were calculated to be 60.68 and 0.0563, respectively. This relation represents the equilibrium dissociation pressure for the reaction U2Zn17 (s) - 2U(s) + 17Zn(v) The solubility of zinc in solid uranium is negligible and the only additional information required to calculate the free energy of formation of U2Zn17 is the free energy of vaporization of pure zinc. K. K. Kelley5 gives the relations, AF°= 30,902 + 6.03Tlog T + 0.275 X 10-3T2 - 45.03T

Jan 1, 1961

An Appreciation of Dr. Douglas by Dr. ALBERT R. LEDOUX The Bulletins of the American Institute of Mining Engineers and the program of the International Engineering Congress, held last September at San Francisco, called attention to an important feature in the pro¬ceedings of the Congress; viz., the public presentation to Dr. James Douglas of the John Fritz Medal, for notable achievements in mining, metallurgy, education. and industrial welfare. Dr. Douglas' health, unfortunately, did not permit of his taking the journey to California. While he had been willing that the bestowal of the medal should be a public ceremony, his natural modesty made him shrink somewhat from what he considered something of an ordeal, and he begged those who were to take part in it to use restraint in anything which they might have to say as to his work and attainments. It was, therefore, with some considerable satisfaction on his side that he learned that the medal would be given him without a public, ceremony in New York, or elsewhere. . On Dec. 5, 1915, the writer of this had the pleasure of handing him the medal, certificate, and official letters of transmittal, at his home at Spuyten Duyvil, where lie was surrounded by his children and grandchildren, with one or two of his most intimate friends. He begged the writer to return his thanks to the Committee of Award; and again to express the feeling that nothing in his career merited so great an honor. On this point all of the members of the Institute will share the writer's feeling that Dr. Douglas is too modest. James Douglas was born at Quebec, Canada, in November, 1837. His father Was a distinguished physician and surgeon, employing his skill in the field of philanthropy: He established the first retreat for the insane in the Dominion, to which lie. devoted himself up to the time of his departure from Canada, when it was taken over by the Government. The son spent 2 years in study at the University of Edinburgh, which lie entered in 1855. Returning to Canada, he graduated from Queens University, at Kingston, Ontario, with the degree of Bachelor of Arts, having also studied medicine, and later theology. After his graduation he traveled extensively with his father in Europe and in the Orient, visiting Egypt several time's. They returned with important archaelogical collections, which Dr. Douglas subsequently donated to the Metropolitan Museum of Art in this city. He then returned to Edinburgh, where he continued his course in medicine, surgery being perhaps his chief interest at that time. He was subsequently licensed to preach and his contemporaries bore testimony to his broad philanthropy and to the sympathy which dominated his every act. His taste was distinctly literary; he had carried off a prize at Edinburgh in English literature.

Jan 1, 1916

By A. Kenneth Schellinger, O. Cutler Shepard

Overgrinding, Or the breaking of ore particles into sizes smaller than required for liberation, is a first-magnitude problem in grinding for concentration processes. The conventional ball mill-classifier circuit used in commercial grinding produces mineral particles that are all ground to pass an upper size limit, while the proportion of very fine sizes, or slimes, is uncon rolled. Calculations based on measurements made in commercial plants which were grinding ore for flotation concentration indicate that about go pct of the energy used in grinding is consumed in useless overgrinding.1 In addition to accounting for the consumption of a large amount of energy, over-grinding is detrimental to the flotation process. Overground slime coats larger partitles and inhibits selective action by the flotation reagents on particles which by themselves could be separated very well. A further difficulty is that extremely finely ground minerals do not respond satisfactorily to flotation-collecting reagents, and both selection and recovery decrease markedly with particles finer than 5 to 10 microns.2 conventional classifier-ball mill circuits inherently tend to overgrind the valuable minerals more than the gangue minerals because most valuable minerals are of higher density and are softer and more friable than the gangue minerals. The rem- edy to this situation would seem to be a separating mechanism which would separate free valuable mineral particles regardless of size and density considerations and a mechanism which would operate in the grinding mill so that valuable mineral grains would be removed from the grinding machine as soon as they are freed. A consideration of these ideas led the authors to the conception of a simultaneous grinding and flotation mechanism. So far as the authors are aware, such a machine has never been tried, even on a laboratory scale. Development oF Apparatus and Experimental Method Apparatus development went through several stages before a really workable machine was devised. Work was started with a large cast-iron mortar 7½ in. in diameter and 8 in- deep. A cast-iron disk Was mounted on the end of a vertical shaft SO that it fitted loosely into the bottom of the mortar. On top of the disk four radial cleats ¼ in. high were bolted to agitate the ball charge as the disk, or impeller, rotated. The vertical shaft was driven at 100 rpm by a mechanism improvised from an old coffee-mill type of grinder. A hole was drilled into the bottom of the mortar through which compressed air was introduced for frothing. In operation, more charges of Ore which had been crushed to pass an 8-mesh screen were placed in the bowl along with water and suitable reagents. The impeller was then started and the compressed air turned On so that the ore was ground while being exposed to air bubbles. Mineralized froth was

Jan 1, 1949

By Paul Hunt

UP TO June, 1923, the Park-Utah mine had shipped about 94,000 tons of a direct-smelting ore of a gross value of $4,200,000, or about $45. a ton. These values were in gold and silver only, although the ore carried small amounts of lead, copper and zinc. Freight, treatment and deductions had averaged $15.40 a ton. At the expiration of the Pittman Silver Act there was in sight about 30,000 tons of a similar ore with a gross value of about $15 a ton in gold and silver, and a large body of partly developed lead-zinc ore of a gross value of about $20 a ton, 40 per cent. of which was represented by the lead-zinc content and the balance by the silver and gold. Mine costs had been high during the life of the Pittman Act, but as a large part of the profits had gone into equipment of the mine and the orebodies were large and had good walls, we knew that mine costs could be greatly reduced. We were therefore faced by the necessity of getting lower freight and smelter rates or of concentrating the ore. We did obtain better freight rates on lower grade ore, and a favorable smelting rate on the small tonnage of siliceous silver-gold ore, but this smelter rate could not be applied to the lead-zinc ore with any profit to ourselves. The Judge mill of the Park City Mining & Smelting Co., with which we were affiliated, was running to capacity; if we built our own mill it meant a 5-mile freight haul to a satisfactory millsite and a year's delay. Fortunately, the International Smelting Co. had just inherited a mill at Tooele which, with some changes, was about double the capacity required for its own ores. Flotation tests were run on Park-Utah ore and a contract entered into with a low base treatment charge per ton, the tariff being largely fixed by the metallurgical deductions. This contract has been admirably calculated so that the miner can follow a lean orebody to its limit. Such a procedure has no doubt made it difficult for the smelting company at times, but it has resulted in finding ore extensions that otherwise might have been missed, so in the long run it has profited too. A flat rate per ton would have been like mining up to the claim endlines in a great many of the stopes. In order to offer such a contract it can be inferred that the smelting company must have been able to make high recoveries and high-grade products on a very lean ore.

Jan 1, 1928

By T. E. Leontis

Several publications1-7 during the past few years have demonstrated the markedly greater effect of cerium, as compared to all other alloying elements, in enhancing the strength and creep resistance of magnesium at elevated temperature either with or without the presence of other elements. In the work reported in Ref. 1-6, the cerium was added in the form of Mischmetal, which contains all the rare earth elements in essentially the same proportions as they occur in monazite sand, the principal ore of these metals. Mellor and Ridley7 have presented the creep characteristics at 200°C of magnesium alloys prepared both with pure cerium and with Mischmetal. Up to the present time, however, no comprehensive study of the effect of the various component elements of Mischmetal on the properties of sand-cast magnesium has been made. This hiatus in magnesium technology undoubtedly is associated with the difficulty in obtaining the rare earth metals separately. This investigation provides such a survey, the object of which was to determine which of the elements present in Mischmetal contributes the greatest effect in developing high strength and high resistance to creep at elevated temperatures. Toward this end the compositional variation of these properties has been determined as a function of temperature in the following alloy systems: 1. Magnesium-Mischmetal 2. Magnesium-cerium-free Misch- metal 3. Magnesium-didymiuin 4. Magnesium-praseodymium- lanthanum 5. Magnesium-cerium 6. Magnesium-lanthanum This designation, based on the names of the metals as furnished by the producer, is used throughout the paper in order to avoid the complicated system of listing all the elements present in the more complex alloys. The composition of the metals and the alloys is discussed in detail below. Preparation of Alloys ALLOYING INGREDIENTS The chemical composition of each of the six alloying ingredients used to prepare the alloys reported in this paper is given in Table 1. In each case, the percent total rare earths, percent cerium, percent neodymium, percent praseodymium, and percent thorium were determined in addition to the listed impurities. The percent lanthanum was determined by difference from the total rare earth content and consequently includes the other elements (samarium, terbium, yttrium, etc.) present in Mischmetal. These additional elements, however, seldom amount to more than 1 to 2 pet of the total rare earth content of Mischmetal. The iron content of the Mischmetal is considerably lower than that of the other metals. This grade of Mischmetal is now readily available. The metals are listed in the order of decreasing complexity. Elimination of the cerium from Mischmetal results in what the trade calls "Cerium-free Mischmetal." Carrying the separation a step further by eliminating the lantha-

Jan 1, 1950

By F. S. Norcross

MANGANESE has long been considered one of the United States' most important strategic raw materials. Its indispensability in steel manufacture makes it vital to the nation's industrial life. Coupled with this indispensability is the fact that domestic producers have not been able as yet to supply more than a small part of the nation's manganese needs; consequently the United States has had to depend upon such distant foreign sources as the U.S.S.R., British India, the African Gold Coast and Brazil for the major portion of its ore. The great bulk of the mineral is consumed in the form of ferromanganese, an alloy that averages 8o per cent manganese and 20 per cent mainly iron and carbon. Manganese is used as a deoxidizer and desulphurizer in steel manufacture. By combination with the residual oxygen and sulphur of the bath, it helps to produce a clean, sound metal. Approximately 14 lb. of manganese, it is estimated, is used in making one ton of steel. For standard-grade ferromanganese, the ore should have a minimum of about 48 per cent Mn and preferably more. Beneficiation methods have not yet been developed for making the immense low-grade deposits in the United States salable at prevailing prices. Dependence upon foreign sources thrust the United States into serious difficulties during the World War. At the start of hostilities in 1914, the nation was obtaining about four-fifths of its ore from the Eastern Hemisphere. Domestic production had been negligible, amounting to only 3000 to 7000 tons a year. As the war continued, shipments from the East, endangered by sea attack and blockade, dwindled rapidly. Imports from Brazil mounted. In this grave emergency, the United States, starting almost from scratch and under the stimulus of high prices, succeeded by 1918 in producing a peak of 311,000 tons, about 3 5 per cent of its consumption that year. Since the war, the United States has depended upon foreign sources for more than nine-tenths of its high-grade ore. During 1936, 1937 and 1938, imports for consumption averaged 736,000 tons a year. During the same period, domestic shipments averaged 21,000 tons a year. Of the imports, the U.S.S.R. accounted for an annual average of 280,000 tons, the Gold Coast 208,000 tons, India 74,000 tons, and Brazil 72,500 tons. But India and Brazil, which in 1936 ranked third and fourth in the list of importers, were displaced in 1937 and 1938 by a new and much nearer source-Cuba. From less than 1 per cent of United States imports in 1931, the island republic increased its shipments to more than 27 per cent in 1938. Cuba's average for this three-year period was 97,000 tons, and its total for 1938 was 131,000 tons.

Jan 1, 1940

By M. D. Hassialis

THE claim is made in a number of patents1,2,3,4 that some compounds of the class known as aryl sulphides have collector properties. One of these patents generalizes the claim to include all aryl sulphides, whose generic formula is R-S¬R[=]-R’ (where x = r,2, . . . ), with the restriction that if the aromatic radicals R, R' contain substituent groups these groups may not contain nitrogen or oxygen. Moses, Hess, and Perkins cite as evidence for their claims the results of flotation tests on Anaconda and Miami copper ores using Biphenyl sulphide, ditolyl disulphide and dinapthyl disulphide as collectors. The use of alkyl sulphides as collectors has also been reported5 with the conclusion that the alkyl sulphides are better collectors than the corresponding aryl sulphides. The experimental work cited appears to confirm this contention. In order to test these claims with respect to diphenyl sulphide, a sample, purchased from the Eastman Kodak Co., was tested against Anaconda ore. The procedure followed was that of Moses, Hess, and Perkins. A sample of ore weighing 500 grams was placed in a laboratory ball mill. To this was added 220 grams of water, 0.06 grams of commercial diphenyl sulphide (1/4 lb. per ton of ore), and 0.8 grams of lime (3 lb. per ton of ore). The material was ground until 93 per cent passed a 65mesh screen. This pulp was diluted to 16 per cent solids. A sample of the diluted pulp was placed in a Minerals Separation type of laboratory flotation cell. After a 2-min. agitation period, pine oil was added and the froth collected for a period of 15 min. This test recovered 68 per cent of the copper, with a ratio of concentration of 6.8: 1. The tailing assay was 0.3 per cent Cu. Moses, Hess and Perkins attained a recovery of 75 per cent, with a ratio concentration of 12: 1. Although these results do not compare too well with those of Moses, Hess and Perkins, subsequent tests showed an improvement, as judged by vanning of the tails. It is concluded, therefore, that the patent results are confirmed. CONTACT-ANGLE TESTS In order to study the response of the various minerals, found in Anaconda ore, to commercial diphenyl sulphide, some contact-angle tests were made. Polished particles of bornite, chalcocite, chalcopyrite, pyrite and quartz were conditioned for 15 min. in a suspension of diphenyl sulphide in water. The concentration of this suspension was 0.284 grams per liter, this being the concentration of this reagent in the ball mill. The conditioned particles were rinsed with water (not rubbed with filter paper or boiled linen) and then tested against an air bubble in the bubble machine, with the following results: born-

Jan 1, 1943

By David A. Thomas, Eugene S. Meieran

MECHAMCAL, electrical, and other property measurements are often more easily made on wires than on sheets. In order to carry out transmission electron microscopy on the same material used for property determinations, we have developed a method for preparing thin foil specimens of wires. The technique was developed for 0.030 in. diam tungsten wires, and is a modification of the thinning techniques used by Wilsdorf, et al 1 A length of wire is first ground to about 0.010 in. thick by mounting the wire in low melting temperature wax, hand grinding a longitudinal flat, removing and reversing the wire in the mount, and then grinding a second parallel flat. The 0.030 in. wide and 0.010 in. thick strip is cut into 1/8 in. lengths to fit in the specimen holder of the electron microscope. Next the specimen is gripped in platinum-tipped tweezers (the anode) and placed 2 mm below a hol- low copper cathode with a 0.010 in. ID nozzle. Electrolyte, 10 pct NaOH, flows by gravity feed through the nozzle onto the specimen, as shown in Fig. l(a). Polishing is carried out until a shallow impression is made on one surface, and then the specimen is turned over and the opposite surface indented. The metal between the two impressions should be about half the specimen thickness, as is shown by the heavy line in the cross section in Fig. l(b). The entire specimen is then electropolishedin 2 pct NaOH until a hole appears at the location of the indentations. The apparatus is shown in Fig. 2, and is essentially the same as that used by Wilsdorf et al. at The Franklin Institute. Light is reflected by a mirror onto the bottom surface of the specimen! which is viewed by a stereoscopic microscope placed above it. Polishing is carried out until light is seen, indicating that a hole has formed, and then immediately stopped. The specimen is washed in water. alcohol, and ether, and is then ready for examination. The specimen should be reversed in its platinum clip during electropolishing to insure equal polishing on both sides of the impression. For tungsten, indenting at 120 v and 0.04 amp takes less than 1 min, and final polishing, at 10 v and 1 amp, less than 5 min. The portion of the specimen available for transmission microscopy surrounds the hole, as is seen by the dashed lines in Fig. l(b). Slight electroetch-ing accompanying electropolishing reveals the mi-crostructure, as seen in Fig. 3(a) by light microscopy. Low-magnification electron microscopy, as in Fig. 3(b), enables the same areas and grains to be viewed and identified when subsequently examined at high magnification. Fig. 4 is a typical structure of

Jan 1, 1963

By J. B. Cohen, M. B. Beaver, R. J. Black

RECENT investigations have shown that face-centered cubic metals may deform by twinning. Blewitt, et al' found that at 4.2"K the mode of def~rmation of single crystals of copper changed at large strains and markings formed on (111) planes. Later they- emonstrated by X-ray diffraction and metallography that the markings were twins and showed that favorably oriented single crystals of copper deformed by twinning at 78°K. They also observed twinning in silver and gold deformed at 4.2 and 78°K. Wagner3 obtained evidence for twinning from the peak shape of diffraction lines of silver cold-worked at 78°K, but twins small enough to cause such effects are not likely to be detected metal-lographically. In the work reported here lamellar structures were observed in deformed silver-gold alloys. They appeared to be mechanical twins, but metallography could not establish this conclusively. Their tendency to form depended on strain rate, temperature and composition. Specimens of silver-gold alloys (0 to 83 wt pct Au) were deformed plastically. One set was worked by hammering under liquid nitrogen, at room temperature and at intermediate temperatures. Another set was compressed slowly in liquid nitrogen to the same reductions as those produced by hammering. Tensile specimens (0.015 x 0.120 x 1.5 in.) of various compositions and approximately equal grain size (0.011 to 0.016 cm) were tested at -195°C and at room temperature. In microsections of all specimens deformed by hammering at —195°C thin lamellae appeared, Fig. 1. They were aligned in definite directions in each grain. In some grains they had two orientations. Where lamellae intersected, a displacement was apparent. Near the center of the left margin of Fig. 1 shear has taken place beyond the fully developed intersecting lamella. Many lamellae resembled Neumann bands in alpha iron. They were parallel to one side of triangular etch pits in the matrix (as in Figs. 1 and 2). The individual lamellae were narrow and had little substructure. This suggested that they did not result from concentrated local slip. The shape of etch pits within the lamellae differed from that of pits in the matrix, as can be seen in Fig. 2; this indicated a difference in orientation. Specimens slowly deformed at —195°C contained regions in which the lamellae were clustered. In these specimens some lamellae were bent and presumably had formed before the termination of the deformation. Structures of greater width than the lamellae were also seen.4 More lamellar structures formed on impact than during slow compression to a given reduction. This was true of all compositions. The structures became less abundant with increasing temperature of deformation. None was observed after extension to fracture at room temperature, but they could be pro-

Jan 1, 1959

The Gooseberry Mine is located 38 krn (24 miles) by road east of Reno, 13 km (8 miles) south of Interstate 80. The mine was originally discovered in 1906 and remained in the control of the Martin family of Fresno, who worked the-property with Mexican ranch hands for 68 years. Westcoast took over the property in 1976 from Apco Oil Corporation. During the time the Martins operated the mine, a 305 m (1,000 ft) inclined shaft was sunk with drifts developed on eight levels exceeding a total of 3,000 m (9,000 ft) in length. It is interesting to note that for over one -half century all development ore was stockpiled. West- coast, the United States mining subsidiary of Home Oil Company Ltd., Calgary, Alberta, completed sinking another vertical shaft to the 396 m (1,300 ft) level. Development work between 122 m and 305 m (400 ft and 1,000 ft) levels has proved the existence of a fine ore body over 300 m (1,000 ft) long. The silver-gold ore grade is fairly consistent in the vertical section, but copper, lead and zinc may show slight increases with depth. Average width of the ore bearing portion of the vein is 2.5 m (8.3 ft). Stoping is by cut-and-fill method. Average silver values within the ore zone have increased from the 152 m (500 ft) level to the 305 m (1,000 ft) level, although the gold values do show some decrease. It is not possible for the geological staff to predict the depth of the ore. However, several years of ore reserves have been proved in the existing mining areas. Important ore minerals are argentite, native gold, and electrum. Trace amounts of galena, chalcopyrite, and sphalerite are associated with the precious metal mineralization. The vein is mainly composed of calcite and quartz. Mine-run underground ore is dumped from the hoisting skip into a coarse ore bin followed by a jaw crusher, an impact crusher, and a 600 mt (650 st) fine ore bin. The mill has a capacity of 317 mt per day (350 st per day). Two-stage grinding is done by a rod mill followed by cyclones with the underflow sent to a ball mill in closed circuit with the cyclones. Cyclone overflow after conditioning receives a primary float in four 1.7 cu m (30 cu ft) cells and a second stage of conditioning ahead of 24 0.8 cu m (30 cu ft) secondary flotation cells. No cleaning stages are used. Flotation tailings are cycloned for a sand-slime separation with the sands used as underground stope fill and the slime portion to tailing dam storage.

Jan 1, 1981

By W. T. Bishop

For many years pine oil has been used extensively as a frother for the flotation of minerals, particularly sulphides, yet the published information available to the average user on its composition, chemical and physical properties, has been rather meager. It is the purpose of this paper to discuss these points and their relationship to the frothing properties of pine oil used in flotation processes. Pine oil, as the name implies, is a liquid obtained from the processing of wood of the longleaf and other southern pines. It is a complex mixture of naturally occurring terpene derivatives, primarily alcohols, and a smaller amount of terpenes, which has found many uses in various industries. Its use as a frother in flotation processes was the first large-scale application in industry and today the mining industry still consumes large quantities of pine oil but the textile and disinfectant industries consume comparable volumes. Much is used in soap manufacture and laundry operations. The surface-active properties of pine oil are in a large degree responsible for this versatility. History The name "Naval Stores" goes back to the days when pine tar and pitch were used to caulk leaky ships and 'Oat their ropes and rigging. Today this term is still used to include not only the oleoresinous products of the pine tree—rosin and turpentine— but other products such as pine oil, pine tar, and the many terpene and resinous compounds obtained by extracting the pine wood or tapping the tree. That part of the industry known as "wood naval stores" dates from about the beginning of this century and today produces a large part of the country's rosin and turpentine by processing pine wood. In addition, all of our natural pine oil is supplied by the wood naval stores industry, as tapping of the live tree gives only rosin and turpentine. This latter phase is known as the "gum naval stores " industry. The first successful commercial operation of the steam and solvent process of the wood naval stores in industry was carried out by Yaryan at Cadillac, Mich., in 1909.1 This operation did not prove profitable, so Yaryan went south to utilize the longleaf pine, and built a plant at Gulfport, Miss.2 Soon after, another plant was built at Brunswick, Ga., which is still in operation, and in 1914 was reported to have processed about 500 tons of wood per day.' In 1921 Hercules Powder Co. acquired the Yaryan interests, at which time the production of pine oil was only 3 to 5 million pounds per year and flotation was the largest customer. As time went on, technological advances were made, other companies entered the field, and the production of pine oil increased many fold. The growth of the industry was especially marked during the past 10 years, and in

Jan 1, 1947

THE Institute assembled in the Court-House, on Tuesday evening, May 22d, and was called to order by Vice-President E. B. Coxe. After announcement by the Local Committee of the programme for excursions, the Secretary read the following annual report of the Council The Council, in presenting to the Institute its annual report, has to record a most eventful year in the history of the Institute. Three meetings, as usual, have been held, two in Philadelphia and one in New York. At the Philadelphia meetings in June and October, there were present many distinguished foreign engineers, some of whom contributed communications to the Institute, and took part in its discussions. Sixty-seven papers have, in all, been presented to the Institute, which will be published in the fifth volume of Transactions. There has been an accession to the membership of 1 honorary member, 11 foreign members, and 162 members and associates; -8 have resigned, 6 have died, and 30 have been dropped from the roll, after due notification, for non-payment of dues. The membership now comprises 5 honorary members, 60 foreign members, and 644 members and associates, in all 699. As worthy of especial mention in the work of the year are the Discussions on Technical Education in connection with the American Society of Civil Engineers, and the report of the-International Committee appointed by the Institute to consider the nomenclature of iron and steel. The Discussions on Technical Education have been published in a separate volume, and comprise a valuable and suggestive collection of the views of practical engineers and educators. The report of the International Committee, composed of Messrs. Akerman, of Sweden; Bell, of England; Tunner, of Austria; Gruner, of France; Wedding, of Prussia; and Holley and Egleston, of the United States, has received the careful attention of engineers and metallurgists of all countries, and has met . with very general acceptance. Of the work of the Centennial Committee in Philadelphia the members are generally familiar, from personal experience, and from the detailed report of the committee at the last meeting of the Institute. But the record of the service rendered by this committee would he incomplete without mention of the numerous letters of thanks and formal expressions of obligations received by the Institute from individuals, societies, and governments abroad. The wise and generous spirit in which the work of the committee was planned, and the laborious and self-sacrificing manner in which it was carried out, call for emphatic expressions of thanks from the Institute. The gifts of Centennial exhibits to the Institute, largely as testimonials for services rendered, has necessitated the appointment of a Museum Committee for

Jan 1, 1878

By W. T. Bishop

For many years pine oil has been used extensively as a frother for the flotation of minerals, particularly sulphides, yet the published information available to the average user on its composition, chemical and physical properties, has been rather meager. It is the purpose of this paper to discuss these points and their relationship to the frothing properties of pine oil used in flotation processes. Pine oil, as the name implies, is a liquid obtained from the processing of wood of the longleaf and other southern pines. It is a complex mixture of naturally occurring terpene derivatives, primarily alcohols, and a smaller amount of terpenes, which has found many uses in various industries. Its use as a frother in flotation processes was the first large-scale application in industry and today the mining industry still consumes large quantities of pine oil but the textile and disinfectant industries consume comparable volumes. Much is used in soap manufacture and laundry operations. The surface-active properties of pine oil are in a large degree responsible for this versatility. History The name "Naval Stores" goes back to the days when pine tar and pitch were used to caulk leaky ships and 'Oat their ropes and rigging. Today this term is still used to include not only the oleoresinous products of the pine tree—rosin and turpentine— but other products such as pine oil, pine tar, and the many terpene and resinous compounds obtained by extracting the pine wood or tapping the tree. That part of the industry known as "wood naval stores" dates from about the beginning of this century and today produces a large part of the country's rosin and turpentine by processing pine wood. In addition, all of our natural pine oil is supplied by the wood naval stores industry, as tapping of the live tree gives only rosin and turpentine. This latter phase is known as the "gum naval stores " industry. The first successful commercial operation of the steam and solvent process of the wood naval stores in industry was carried out by Yaryan at Cadillac, Mich., in 1909.1 This operation did not prove profitable, so Yaryan went south to utilize the longleaf pine, and built a plant at Gulfport, Miss.2 Soon after, another plant was built at Brunswick, Ga., which is still in operation, and in 1914 was reported to have processed about 500 tons of wood per day.' In 1921 Hercules Powder Co. acquired the Yaryan interests, at which time the production of pine oil was only 3 to 5 million pounds per year and flotation was the largest customer. As time went on, technological advances were made, other companies entered the field, and the production of pine oil increased many fold. The growth of the industry was especially marked during the past 10 years, and in

Jan 1, 1947