Search Documents

By L. J. Demer, W. W. Walker

AMONG several variables of the indentation hardness test is the effect of loading time on the measured hardness of a material. The most generally recommended duration of loading is 10sec.1-3 Although this short loading duration is undoubtedly satisfactory for harder metals, it is questionable that it is sufficient for very soft metals,4 or for certain plastics.5 The effect of duration of loading on the measured hardness of ionic crystals is largely unknown, although Onitsche and Mitsches found that the indentor (under a very low load) had not yet reached equilibrium after 60 sec in a variety of ionic crystals. To extend further the data of Onitsche and Mitsche, a systematic study was made of the effect of duration of loading for longer periods, up to 50,000 sec, on the 136 deg Dph of synthetic lithium fluoride. For comparison, less extensive tests were made on synthetic magnesium oxide and copper single crystals. The general procedure used was to indent a cleaved and polished (100) face of a lithium fluoride crystal using a Leitz Durimet microhardness tester. In certain cases, the indentor was so oriented as to align the diagonals of the 136 deg diamond pyramid indentation parallel to a (100) edge. In other cases the diagonal of the indentation was aligned at 45 deg to a (100) edge of the crystal. After indenting, the surface tested was etched in the acid etchant recommended by Gilman and Johnston.' This revealed the position of dislocation lines which intersected the surface tested. At these points of emergence were formed the usual sharp, pyramidal etch pits as shown in Fig. 1. The specific procedure used in studying duration of loading was as follows. The surface of the crystal was indented, and the load was left on the indentor for a predetermined time. This duration of loading was varied systematically from 1 to 50,000 sec. After the desired amount of time had elapsed, the indentor was removed from the crystal and the size of the resulting indentation was determined using a micrometer eyepiece. The surface was then etched to reveal the dislocation etch pit pattern around the indentation. Procedures used for lithium fluoride, magnesium oxide, and copper were similar. Preliminary studies revealed that, although an indentation was enlarged by increasing loading time, no corresponding changes occurred in the surface etch pit pattern. Since no evidence of dislocation movement was observed on the surface, it was assumed that the plastic deformation indicated by the indentor sinking into the surface was a result of dislocation movement inside the crystal. This movement was studied bf making a series of surface indentations in a crystal corresponding to various lengths of time, cleaving the crystal vertically through the indentations, etching the freshly

Jan 1, 1964

By George Packard

THE shaft of the Raven. mine, at Butte, Mont., is an incline 1,700 ft. in length and dipping at various angles. At the top the dip is 70° from the horizontal, but this is gradually flattened until at the 300-ft. level the inclination is only 47°. This angle continues to the 1,100-ft. level, below which it, curves with a 125-ft. radius to 78°. In addition to these variations in dip, the shaft does not lie in the same vertical plane, with the result that the hoisting rope not only rubs at intervals on both the hanging- and foot-walls, but presses strongly against the west, dividers near the collar, while 300 ft. below it runs close to the east end plates. The early operators used no idlers, and wall plates cut 6 in. deep y the rope resulted. Later operators first attempted to overcome the excessive friction, and the wear of rope and wall plates, by introducing solid cast-iron idlers, 3 in. in diameter. To allow for the travel of the rope from side to side some of these had to be 3 ft. long and were very heavy. Judging from the appearance of the old idlers of this type found at the mine, they often failed to turn in the bearings, which is not surprising when it is considered that they would have to make 1,000 rev.. a minute under ordinary hoisting conditions. The next rolls were made of wood, 6 in. in diameter, with an iron band about each end, and a pintle of 1-in. round steel driven in at the ends to serve as a shaft. These wore rapidly, and were soon replaced by rolls made from water pipe, 5 or 6 in. in diameter, cut to the desired length and fitted with a wooden cylinder into which the pintle was driven. Where the idlers were used on the hanging-wall of the shaft the original bearing was simply a piece of 2 by 1-1 in. strap iron, 10 in. long, turned up at the end in a circle of 18 in. in diameter to receive the shaft. A small hole served for oiling, and common black oil was generally used, although filtered oil from engine bearings and compressor bearings was also used. When the rolls were to be placed on the foot-wall the bearings were made from two pieces of 1 by 3 in. steel, 6 in. long. A half circle was cut on the flat side of each piece and the two half circles together formed a bearing. Oil holes were provided, and in some cases holes were bored through the two pieces so that they could be screwed or spiked to the wall plates.

Jan 8, 1914

By A. W. Schlechten, W. J. Kroll

As this paper is written, the only method for the commercial production of lithium metal is by the fusion electrolysis of LiCl-KCl mixtures, as first proposed by Guntz.2 The details of the industrial process have not been made public but Osborg8 stated that an efficiency of more than go pct is obtained with a lithium metal recovery above 95 pct and that the metal is 99.5 pct pure. Pletenev9 gave a power consumption of 66 kw-hr per kilogram of lithium metal produced with a salt consumption of 9 kg of LiCl and 0.4 kg of KCI. Pletenev's figures indicate a somewhat lower recovery than that given by Osborg. In a recent report on German lithium plants, Motock7 gives figures that are also less favorable than those reported by Osborg. At the German plants the lithium recovery in electrolysis was only 83.4 pct, with a power consumption of too kw-hr per kilogram of lithium. The metal averaged only 97 pct pure, with sodium and potassium as the chief impurities. The presence of SO2, SO3, Si02, Ba, Ca, and appreciable amounts of Na and Fe2O3 were especially disturbing in the electrolysis, and it was necessary to run the cell for some time to eliminate most of these impurities and condition the bath. It may be noted here that most of these impurities do not interfere with a thermal reduction process. These facts show that the present method of producing lithium is fairly efficient and would suggest that other methods could not compete. However, fusion electrolysis has certain drawbacks, such as the necessity of supplying costly, low-voltage direct current and of collecting and processing the anodic chlorine if it is not to be wasted. An even greater disadvantage is that lithium chloride must be used for an electrolyte. It is one of the most expensive salts of lithium, since it cannot be produced in anhydrous form by precipitation from aqueous solution, as is done with LiF or Li2CO3. The reduction of lithium by a vacuum process similar to the ferrosilicon method for the production of magnesium would have certain advantages. Small units, such as Pidgeon retorts, would give flexibility of production to meet demand, and a small plant would require moderate capital outlay. There is a possibility of using idle Government-owned magnesium plants for such purposes. The raw materials needed for vacuum thermal reduction would not have to be extremely pure, especially with respect to the iron and calcium content. This paper describes a series of experiments to determine the effectiveness of various agents for the reduction of lithium compounds. The investigation is part of a program of vacuum metallurgy con-

Jan 1, 1947

By R. W. Fenn, H. A. Lepper, W. R. Hibbard

THIS paper reports the results of static tension and torsion tests made on single crystals of alpha brass for the purpose of determining its elastic coefficients. 70-30 alpha brass was chosen because it has been used extensively in the study of the plastic deformation and because it has the following desirable characteristics: (1) face-centered cubic structure, (2) marked elastic anistropy, (3) low elastic modulus. In 1928 Masima and Sachs' using static methods reported the following values for the elastic coefficients of 72-28 pct alpha brass: S11 = 19.4 X 10-13' cm2 per dyne S12 = —8.35 X 10"' cm2 per dyne S44 = 13.9 X 10-13= cm2 per dyne These values were obtained from the measurements shown in fig. 1. The experimental points for both tension and torsion lie consistently below the lines drawn to represent them. Fig. 2 shows the stress-strain curves for their specimens. Only a few points in the elastic range of these curves were available to obtain their values for Young's modulus. Therefore, it was considered that a re-evaluation of these data was desirable. In addition a variation of from 1.13 to 1.485 kg per mm2 was found in the values of the critical resolved shear stress for 70-30 alpha brass reported by Burghoff,² Treuting and Brick: Martin,4 Maddin, Mathewson and Hibbard5,6 and von Goler and Sachs.' Therefore, it was desired to evaluate the conclusion of Boas and Schmid8 that a constant resolved shear stress and not a constant elastic shear initiates plastic deformation. Theoretical Considerations*: The elastic deformation of cubic crystals may be defined by three elastic coefficients (S11, S12, S44,) or three elastic parameters (C,,, C,, C,,). These coefficients or parameters are sufficient to define the stress and strain relations for cubic crystals in the generalized form of Hooke's law referred to Cartesian coordinates. Elastic parameters and coefficients in the cubic system are related by the expressions: C11 —S11+S12/(S11-S12)(S11+2 S12) C12=-S12/(S11-S12)(S11+ 2 S12) (S11 — S12) (S11 + 2 S12) [2] C44 =1/S44 PI It is possible to determine all the elastic coefficients for a cubic metal by measuring two of the three elastic constants: Young's modulus (E), torsion modulus (G), or compressibility (S). The following relations exist between crystallographic orientation and E, G and S for cylindrical crystals of the cubic system: 1/E = S11 — 2 [(S11 - S12) — Su] (?1² ?2² + ?2²?83 + ?3² ?1²) [4]

Jan 1, 1951

By J. R. Cahoon, W. V. Youdelis

FOR the diffusion of copper in silver-rich alloys, there have been only two previous investigations, that of Seith and Peretti in 1936, and that of Sawatzky and Jaumot2 in 1957. Seith and Peretti obtained a value of 24.8 keal per g-atom for the activation energy of diffusion whereas Sawatzky and Jaumot obtained a value of 46.1 keal per g-atom. Admittedly, Seith and Peretti used relatively high concentrations of 2 at. pet Cu and polycrystalline diffusion couples, while Sawatzky and Jaumot investigated tracer diffusion in single crystals of silver. The difference in the results, however, seems too large to attribute solely to solute concentration, as a change of over 20 keal per g-atom in the activation energy suggests a change in the mechanism of diffusion. Therefore, in the present investigation the diffusion coefficient for copper in polycrystalline Ag-2 at, pet Cu alloy is re-established using conventional sandwich-type diffusion couples and electron-probe microanalyses, and the results are compared with those of the previous studies. The diffusion couples were prepared from high-purity silver (99.999 pet) and high-purity copper (99.999 pet). The silver disks, 1/4 in. long and 4 in. in diam, were machined from an ingot which had been solidified in a dynamic vacuum of 10-3 mm of Hg to eliminate oxygen absorption which otherwise would result in copper oxide precipitation in the weld zone. The alloy disks of similar dimensions were machined from an alloy ingot (nominal composition 2 at. pet Cu) which had been unidirectionally solidified to obtain a predictable solute concentration,3 and homogenized for 1 week at 800°C. Sandwich diffusion couples were made by pressure welding an alloy disk between two silver disks in an induction heating coil. The couples were diffusion-annealed at temperatures of 800°, 756°, 699°, and 630°C in tube furnaces in which the temperature was controlled to better than ± l°C. The diffusion couples were examined metallographically for weld defects, and couples showing even minute defects at the weld interfaces were rejected. Concentration penetration curves were established using an A.R.L. Microprobe analyzer. CuKO radiation was counted and converted to concentration using 0.5 and 1.0 wt pet Cu chemically analyzed standards. Initially, four continuous profiles were obtained, and averaged to obtain the final diffusion curve. The initial analysis was performed commercially and the welds were not located with respect to the profile. Therefore, the results were rechecked by the authors using the Mellon Institute A.R.L. probe. In the latter case, concentrations were obtained at 10-µ steps for four different traverses, and then averaged to obtain

Jan 1, 1968

ON Oct. 5, 1926, the day before the general ses-sions of the fall meeting of the American Insti-tute of Mining and Metallurgical Engineers at Pittsburgh, a round table conference on the combus-tibility and testing of coke was held at the Bureau of Mines Experiment Station. There were about fifty present, with A. C. Fieldner, chief chemist of the Bureau of Mines, as chairman. The following organi-zations were represented: American Institute of Min-ing and Metallurgical Engineers, American Society for Testing Materials, American Gas Association, Eastern States Blast Furnace and Coke Oven Association, Gas and Fuel Division of, American Chemical Society, and Southern Ohio Pig Iron and Coke Association. In opening the proceedings, Mr. Fieldner explained that the meeting had been called at the suggestion of several members of the Institute and members of other organizations. The subject is of interest to the pro-ducer and the user of coke whether it be in a blast furnace, cupola furnace, house-heating furnace, open grate, gas producer, or in a water-gas generator. There has been much confusion on this subject largely because there is no common definition of combustibility. Does the blast-furnace superintendent, the coke-oven operator, and the fuel engineer have the same under-standing of the term "combustibility"? If a common understanding can be reached, many differences of opinion will disappear. COMBUSTIBILITY OF COKE R. H. Sweetser of Columbus, Ohio, disagreed with the statement of P. H. Royster, T. L. Joseph, and S. P. Kinney in Reports of Investigations, Serial No. 2524, of the Bureau of Mines, in which it was stated that the coke-oven op-erator cannot change coke combustibility by modifying oven practice. Mr. Sweetser held that the coke-oven man can change the combustibility of coke. Blast-furnace men know that coke that will burn easily with low pressure and will. come down in the regular way in the furnace can be pro-duced from a given mixture of coal. His idea of the combustibility of coke is the rate of flow through the com-bustion zone of the blast furnace. If the coke does not pass through in normal manner it is highly incombustible. H. J. Rose of the Koppers Co., Pittsburgh, objected to being pinned down so closely on this phase of the com-bustibility and incombustibility of coke. Coke-oven men are frequently obliged to change oven conditions to make a coke which gives blast-furnace men what they want. The size of the coke and the screening have an important bear-ing on combustibility, and there are many cases on record where by simply changing the different sizes of the coke, everything worked smoothly, and that is a much more combustible coke.

Jan 1, 1927

By Herman Garlichs

THE development of the extensive Southeast Missouri deposits greatly preceded that of the Iowa and Wisconsin deposits. It began about 1720 at Mine La Motte and other localities, and has continued uninterruptedly to the present time. It is estimated that this district produced about 184,000 tons of lead in the year 1916, having a value of approximately, $25,000,000. This is a new high record. The Southwest Missouri orebodies were hardly known before 1845 and were not extensively developed until 1870: Lead production in South-west Missouri for 1916 was 38,788 tons. Oklahoma produced 14,399 ,tons and Kansas 2,345 tons, making a total for Southwest Missouri, and the adjoining districts in Oklahoma and Kansas, of 55,532 tons of lead. The first metallurgists in Missouri were the Indian and the hunter. The early settler learned to procure his bullets either by melting ore in his camp fire or by throwing pieces of galena on an old stump and depending on the usual roasting and reaction method to obtain the metal. A little more refined method was to arrange two flat stones in the form of a V. Wood and galena were placed in the furnace and ignited. As heat developed, some of the metal was extracted and molded into bullets. The next step in utilizing the lead ores was the log hearth. All lead in Missouri was smelted in this crude affair before 1820. It was built on sloping ground, and consisted of a hearth of stone, surrounded on the front and two sides by a stone wall. The wall was 7 ft. high in front. The top and rear end were left open and in front an arch or opening was made, forming the eye of the furnace. In front of this a pit was dug in the ground, to receive the molten metal. Large logs were rolled in at the back and made to rest upon ledges formed inside, to raise them from the hearth and to give a draft. These logs filled the entire width of the furnace. Small split logs were then set up around the two sides and the front, and the ore was piled on until the furnace was full. Finally, the mass was covered with logs and fuel until the ore was completely surrounded. A gentle heat was started, which was raised very gradually. After 12 hr. the heat was increased and continued for 12 hr. more, 24 hr. being required, for each smelting. The furnace treated about 5,000 lb. per 24 hr. and the ore yielded about 50 per cent. of its metallic lead. A considerable quantity of the ore was not desulphurized, and fell between

Jan 7, 1917

SOME days ago a visiting member from Pittsburgh who is an ardent supporter of the Institute remarked: "There are a lot of men who would be members of the Institute if it weren't so expensive. It is not so much the $15 dues as the $20 initiation fee. This makes quite a hurdle, especially for the younger fellows." A little further conversation developed the fact that the member had never learned of the changes in the By-laws regarding initiation fees and dues made by unanimous vote of the Board of Directors last November. As a great many others doubtless are unaware of these changes, the substance of two of the amendments is here repeated. They provide: (1) That the initiation fee for Junior Members (heretofore ten dollars) he abolished. (2) That the age limit for entrance as a Junior Member be increased from 27 years to 33; provided further, that the period during which the dues of a Junior Member are ten dollars shall be a maximum of six years but in no event shall extend beyond his thirty-third birthday. The Junior Member gets the identical privileges enjoyed by his seniors and he likewise assumes the same obligations with the sole exception of the financial payments. This one exception is justified by the fact that the engineers of more mature years, who are established in the profession, - are able and willing to assume a slightly greater financial burden. In effect, it is a small subsidy for the younger men; but these in turn will later enter the group of those that give instead of receive assistance. The practical result is that an engineer under 27 can obtain every privilege and benefit of membership for six years on the payment of only $10 per year without any initiation fee. A man of thirty can do the same for a period of three years. Incidentally, a candidate applying for membership (either as senior or junior) in the next few months need pay dues for the second half of 1935 only. A Junior Member -can be enrolled with an immediate outlay of only $5. The Institute does not seek-members indiscriminately merely to swell the number. These facts are not presented as a "bargain" offer in any sense. The standards for admission are high and are watched zealously. But it frankly-wants to give qualified men who can benefit from membership every encouragement to apply. Naturally, the Institute does not want lack of accurate information regarding initiation fees and -dues to be a stumbling block to any that are eligible and desirous of enrolling. Members are urged to take it upon themselves to clear up misapprehensions on this point, particularly among younger engineers.-Editorial reprinted from MINING AND METALLURGY, May, 1935.

Jan 1, 1935

By W. H. Gunniss

When the copper smelters were built, in Montana, all of the refractory products which were used in their construction were shipped in from Eastern factories. It was apparent that if a material suitable for the manufacture of these products could be found within the State, a saving of freight could be effected and a new industry built up. Prospecting for such materials was started and experiments were made with samples from numerous deposits. Considerable effort and funds were expended in an attempt to manufacture silica brick from Dillon quartz, a light colored sandstone that is found near Dillon, Mont., on the Oregon Shortline railroad. As a brick material the Dillon quartz was a failure, but it has proved very satisfactory as a silica cement. It is now being used in laying silica brick and for reverberatory furnace bottoms. A bed of quartzite that is particularly suited to the manufacture of high-grade silica brick was finally discovered at Browns Spur, 6 miles west of Anaconda. The material from this deposit is now being used in the manufacture of the Anaconda silica brick, which have gained a wide reputation for heat-resisting and lasting qualities. The analysis of an average sample of this quartz is: SiO2, 96.7; Fe2O3, 0.3; Al208, 2.5; CaO, 0.3 per cent. The very low percentage of fluxing ingredients makes this a most refractory material. All of the Anaconda silica brick are hand molded. Various types of brick machines have been tried, but the hand-mold process proved the best suited to the manufacture of silica brick from this material. The silica is first put through a jaw crusher and is then dumped into wet pans, where 4 per cent. of lime paste is added, to produce a bond. Without the lime the material would not be plastic enough to mold. After a few minutes' grinding in the wet pans the material is conveyed to the molder, who forces it into the molds by hand. The brick are then dumped on pallets and placed in the drier, where they are left. until dry enough to be set in the kilns. Some of the brick are re-pressed before being dried. They are burned about five days, in round down-draft kilns. It is not necessary to have as much heat in the kilns as the brick will be subjected to when in use in the furnaces. Montana refractories are used in smelters throughout the West. Prospecting for fire clays was also carried on. After experimenting with clays from several different deposits, it was found that a mixture of

Jan 1, 1914

By W. D. Robertson, D. A. Koss, A. J. Goldman

THE significance of the hcp (E) structure, which appears when Fe-Cr-Ni alloys (stainless steels) are transformed martensitically, has been the subject of considerable study and speculation.'-7 It has been proposed that the hcp structure is an intermediate phase in the transformation: fcc (austenite) — hcp (E) -bcc (0, martensite). However, recent studies by transmission electron microscopy6,7 have indicated that the hcp structure may be a consequence of the large shear strain (10 deg) associated with the fcc to bcc transformation. That is, the transformation to a bcc structure is accompanied by extensive dissociation of dislocations in the parent austenite, which has a low stacking-fault energy.'-'' X-ray diffraction analysis of the transformed alloy reveals a pattern of lines corresponding to an hcp structure, together with the parent austenite and the bcc product. The fact that the hcp structure is observed only in association with the bcc product in these alloys1'4'6'7 lends support to the conclusion that the hcp structure is a secondary product of the transformation. But, the evidence is circumstantial and more definite resolution of the two possibilities mains to be obtained. If the hcp structure is an intermediate product of the transformation, as in 1) above, then two distinct Ms temperatures should be observed, Ms and To evaluate this possibility, three different techniques that are particularly sensitive to the structural changes accompanying such transformations have been used in an attempt to detect two transformation temperatures in an Fe-15.1 Cr-11.7 Ni alloy: 1) high-sensitivity differential thermal analysis, 2) the temperature dependence of resonant frequency (elastic moduli), and 3) internal friction of cylindrical specimens vibrating in either longitudinal or torsional modes. To obtain the necessary sensitivity, a differential thermal analysis technique was developed for the purpose, Fig. 1. The differential temperature between a nickel standard and the specimen was amplified to produce a sensitivity of 0.02OC (0.7 v) in temperature difference. The specimen and the standard were surrounded by a copper block and the entire assembly was immersed in a solution of methyl and ethyl alcohol, freezing point, - 140OC, which provided the necessary thermal stability to reduce temperature fluctuations to negligible proportions. A cooling rate of about 1.5OC per min was obtained by bubbling liquid nitrogen through the liquid bath. In order to calibrate the experiment with respect to the evolution of heat in the transformation from fcc to hcp structures, differential cooling curves were obtained for an Fe-19.8 Mn alloy, which transforms martensitically to E.'"-' a Ms(e) temperature of 145°C was clearly defined by a temperature

Jan 1, 1964

By G. E. Tardiff, A. A. Hendrickson

THE objectives of this communication are to present the solid-solution strengthening data for silver-base zinc single crystals and to evaluate the importance of strength contributions from several mechanisms through the use of this data combined with that for the silver-base aluminum case.' Some features of the yield point behavior of silver-base zinc crystals were previously reported.' Silver-base zinc alloys were prepared by induction melting 99.99 pct Ag with 99.9 pct Zn in high-purity graphite crucibles contained in argon-filled quartz tubes. After the first melting, the ingots were cut into short lengths, redistributed in the molds, and remelted in order to reduce solute-concentration variations. Alloy single crystals were then grown from the melt through the use of a modified Bridgeman technique which consisted of lowering the graphite crystal mold through a hot zone at a rate of 3/8 in. per hr. As in the melting operation, the molds were contained in argon-filled quartz tubes. Gage lengths 2 cm in length were introduced by both spark machining (circular cross sections) and abrading and acid etching (rectangular cross section) followed by electropolishing (a comparison of the critical resolved shear-stress values prepared by the two techniques showed no differences in strength values). The final cross-sectional areas of the crystals were approximately 5 sq mm. Prior to testing, the crystals were annealed at 600°C for 20 hr in argon atmospheres, furnace-cooled, and lightly electropolished. Crystal orientations were determined using the back-reflection method. The tensile testing was done on a Model FM Instron at a strain rate of 1(T4 per sec. Test temperatures of 77", 200°, and 400°K were attained by immersing the specimens in liquid nitrogen, dry ice-acetone mixtures, and silicone oil, respectively. The critical resolved shear-stress (CRSS) values for silver-base zinc crystals as a function of composition and testing temperature are given in Fig. 1. It will be noted that the CRSS for silver-base zinc solid solutions, as in the silver-base aluminum1 case, depends on temperature in a manner typical of fcc solid solutions: at high temperatures (-300°K and above), the CRSS is relatively temperature-independent but becomes strongly dependent on temperature at lower testing temperatures. A reasonable picture of solid-solution strengthening for silver-rich solutions at room temperature based on "direct" strengthening mechanisms3 is as follows. Since silver alloys have low stacking-fault energies, extended dislocations are expected and it is possible that Suzuki locking4 makes the major contribution to the room-temperature solute strengthening. This provides essentially temperature-independent strengthening since thermal motions of the dislocation line are not large enough to aid the dislocation in escaping the solute atmosphere extending over the fault width. An estimate of the

Jan 1, 1964

By P. W. Bakarian

PREVIOUS determinations1,2,3 of the texture of magnesium and its alloys have shown only slight variations in the principal features of the structure. This investigation presents pole figures for magnesium and two of its alloys, in which differences of some magnitude will be shown. Schmid and Wassermann have considered the texture of magnesium in analogy with that of zinc-also a hexagonal lattice. Whereas the zinc texture is said to be derived primarily through basal slip and secondarily through {102}† twinning, the {102} twinning is considered impossible at the later stages of the rolling in magnesium because of its smaller axial ratio. This state of affairs appears reasonable for pure magnesium, but for alloy textures the situation is more complex. A double orientation similar to that found in zinc has been reported by J. D. Hanawalt,4 and the addition of small amounts of calcium to magnesium and its alloys to produce a double texture was noted by J. C. McDonald.5 The pole figures of this investigation, using an improved X-ray technique, show these various textures. The dependence of directional properties of rolled sheet on modifications of texture is well recognized. Correlation of physical properties with existing texture should be even more significant if quantitative valuations are attached to the various areas on the pole figures. Such a quantitative technique is developed herein. EXPERIMENTAL METHOD Two alloys were used, besides high-purity magnesium. In each case, the metal was extruded to bars 32 in. thick and hot-rolled to a thickness of about 0.075 in. It had been established previously that such a reduction was more than sufficient to eliminate the extruded structure. The rolling proceeded in the same direction as that of the extrusion, without any cross rolling. The temperatures corresponded to normal commercial practice, averaging around 600°F. A unique method of preparing the sample was developed in this work. Instead of using a flat specimen, a stem of the metal was cut out of the rolled sheet in the desired direction (rolling direction) as shown in Fig. 2. From a sheet of 0.075 to 0.065-in. gauge, the stem was cut to a square cross section with a jeweler's saw, rounded with a file and polishing paper to a diameter of 0.060 in, and evenly etched in dilute hydrochloric acid to a diameter of 0.038 ± 0.001 in. In this way, a cylinder of the original sheet with its axis in the desired direction was produced. By using this type of specimen for the pin-point pictures, any variance in the absorption of the diffracted beam at the various angular settings of the specimen, was completely eliminated.*

Jan 1, 1941

By R. D. Fisher, A. G. Metcalfe, F. A. Crossley

AN investigation of the application of magnetic stirring to the consumable arc melting of aluminum and nickel demonstrated that grain refinement could be obtained when there was sufficient stirring force. Also, it was found that grain refinement could be obtained in aluminum by alternately reversing the polarity of the current through the magnetic stirring coil. The effect of the latter was to periodically reverse the direction of rotation of the molten metal.' Because of their promise, these findings were applied to conventionally cast aluminum. Shortly after this work was begun, Kondic2 reported experiments in which aluminum cast with 40° C (72° F) of superheat exhibited a grain size of 10 to 20 grains per cm2. When interrupted rotation was applied during solidification by mechanical means, a grain size of 800 to 1000 grains per cm2 was obtained. Magnetic Stirring Applied to Conventional Casting— The applicability of magnetic stirring to producing grain refinement in conventionally cast metal was evaluated in the following way. Three pounds of aluminum were cast into a clay-bonded graphite mold. The mold was surrounded by a magnetic stirring coil of 1000 turns. A direct current of 200 amp was passed through the casting by means of a graphite electrode which was immersed from the top. A current of 5 amp was passed through the stirring coil. The aluminum (1100 or 25) was superheated to 1600° F (871° C) and fluxed by passing chlorine gas through the melt for 2 min prior to casting. Two additional castings were made for comparison: 1) a conventional casting of metal superheated to 1600° F and 2) a similar casting through which 200-amp current was passed during solidification, but without current in the magnetic coil. Macrosections of these three ingots are shown in Fig. 1. Very remarkable grain refinement resulted in the magnetically stirred casting. It may be noted that the casting through which 200-amp current was passed has a coarser structure than the conventional casting. It would appear that this is due to the additional heat input generated by the current to the former casting. Mechanical Rotation Applied to Conventional Casting—A casting temperature of 1600° F was used throughout. Some 1 1/2 -lb castings rotated at 150 rpm were predominantly columnar with small areas of coarse, equiaxed grains close to the lower mold wall. Following these, a series of 3-lb castings was made. Macrosections of these ingots are shown in Fig. 2. The imposed rotational speed was 250 rpm. Turbulence or acceleration in the solidifying liquid was the significant factor. Fine grain size resulted in the material solidified during the period of acceleration of the liquid to the imposed rotational speed. When uniform rotational motion was achieved, the grain structure reverted to columnar. The final casting shown in the lower right-

Jan 1, 1962

By Joseph J. Yancik, Leonard L. Felts, George B. Clark

LITTLE information has been published concerning the actual or useful amount of energy obtained from explosives when they are used for blasting. To provide more data on this subject, 8-in. neet cement cubes were blasted in a steel plate box and the breakage energy evaluated by comparison with drop crusher results using Rittinger's,1,2 Kick's: and Bond's' theories. Theories by Bond and Wang," Lineau," Hatch,' Roller,' and others0-11 were not considered applicable. Those used in this investigation may be expressed mathematically as follows: Rittinger Theory E = KrS2, pet,—--------------- [1] 40 d1 d0 Kick Theory TV 1 1 E = =K, [S pct. log1/d+ 100 log d0] [2] 40 d1 L. L. FELTS, Junior Member AIME, was formerly a Graduate Assistant, University of Illinois. G. B. CLARK, Member AIME, was formerly Professor of Mining Engineering, University of Illinois, and is now Chairman, Dept. of Mining Engineering, Missouri School of Mines and Metallurgy. J. YANCIK, Junior Member AIME, is a Graduate Assistant, Missouri School of Mines and Metallurgy. This paper, TP 4213A. is revised from a thesis submitted by L. L. Felts in partial fulfillment of the M.S. degree in Mining Engineering, University of Illinois, 1954. Discussion may be sent (2 copies) to AIME before May 31, 1956. Manuscript, Dec. 27, 1954. Bond's Third Theory E = Kb [S pct. log1/d1+ 100 log d0] where E — energy used in breakage, d, = average diameters of screen fractions of broken cement particles, pct, = percent weight of diameter d;, and 2 pct, = 100 pct. The above equations were employed to determine values of Kr, Kk, Kb for particle size distributions similar to those obtained from the blasting curves. These values were in turn used as a means of approximating the specific energy of the blasted material. The efficiency of crushing by blasting was then determined by dividing this specific energy by the maximum available work of the explosive per gram of cement. Knowledge of the failure of solids under static loads is developing very rapidly. Their failure under impact loads has been investigated and reported in the literature only to a limited extent. Theories of failure' hnder static loading include 1) the maximum stress theory, 2) the maximum strain theory, 3) the theory of constant elastic strain, 4) theory of maximum shearing stress, and 5) Mohr's theory of strength. All of these have elements of usefulness in establishing an applicable theory for blasting. For highly strained and compressed material such as that surrounding a detonating charge of high explosive, the Mohr theory and its implications appear to be the

Jan 1, 1957

ASIDE from the John Fritz Medal, in which the Institute participates through its representation on the John Fritz Medal Board, the Institute itself has four awards it may make annually, as follows : the Robert W. Hunt Medal and Prize, the J. E. Johnson, Jr., Award, the James Douglas Medal, and the William Lawrence Saunders Medal. ROBERT W. HUNT MEDAL AND PRIZE The partners of Robert W. Hunt established a fund which was presented to the Institute at a fitting ceremony on May 27, 1920, to establish an annual medal and a sum of money to be awarded under the following rules 1. The award shall consist of two prizes: first of a gold medal, second of a sum of money; a certificate to accompany each prize, The money prize shall not be awarded to a member over 40 years of age, but under unusual circumstances, both prizes may be allotted to one person provided that he is not over 40 years of age. In general it will be understood that the Committee shall award the money prize to the younger men, rather than the medal. 2. The awards shall be made not oftener than once a year to that person or persons contributing to the Institute the best original paper or papers on iron and steel. The scope of the term "iron and steel" shall be determined by the sub-committee considering the awards. In general, papers dealing with the practical side of the subject have preference over those dealing with the theoretical side in recognition of the fact that Captain Hunt's main contributions to the industry have been in the improvement of production and quality of material. 3. A sub-committee of three to five, including the Chairman of the Iron and Steel Committee, shall be appointed by the Iron and Steel Committee annually to adjudge the award subject to approval. 4, The awarding committee shall submit its report to the Iron and Steel Committee at its October meeting, and the award shall be certified to the Secretary of the Institute in time to permit the presentation to be made at the Annual Meeting of the Institute, 5. The recipient of the award shall be designated "The Hunt Medallist," This prize is administered by the Iron and Steel Committee. Awards of the medal have been made as follows 1920-Robert Woolston Hunt. 1926-Charles Lewis Kinney, Jr. J. E. JOHNSON, JR., AWARD This award is made from the income of a fund of $3000 donated by Mrs. Margaret Hilles Johnson in memory of her husband, J. E. Johnson, Jr., who was a prominent engineer, author of two valuable volumes on iron blast-furnace construction and practice, vice-

Jan 1, 1928

The great Bingham Canyon mine and mill complex of Magna, Arthur, and Bonneville had their beginning in a 300 ton per day operation which was commenced by Daniel C. Jackling and his associates in 1904 as the Utah Copper Company. This small plant was quickly expanded to 500 tons per day and eventually Kennecott, the Utah Copper successor, was processing about 45,000 tons per day of ore in each of its mills, Magna and Arthur. Finally, in 1966, the Bonneville crushing and grinding plant was added to produce a slurry of ground ore for flotation concentration at the expanded Magna and Arthur mills. Bonneville is one of the few railroad dump primary gyratory crushing plants constructed in recent years; another which is described in this Monograph is Cuajone in Peru, started in 1976. Two others are the Climax Henderson unit and the Phelps Dodge Tyrone crusher, which has been fed by trucks since it commenced operation. The Bonneville, Henderson, and Cuajone crushers are all located considerable distances from their mines, hence the use of rail haulage. Shovels in the Bingham pit are 8 to 15 yd capacity; and ore is sent to the Bonneville crusher in 100 ton rail cars, where they are dumped, two at a time, by a hydraulically driven rotary dumper. Ahead of the 54 in. by 74 in. Allis-Chalmers gyratory are two grizzlies, each 27 ft 9 in. (8.46 m) long with bar spacings of 4 ½ in. (114 mm) at the feed end and 6 in. (152 mm) at the discharge end. Grizzlies are sloped at 38. Oversize rocks are re- moved from the crusher pocket by an overhead crane, and the crusher produces a nominal 6 in. (152 mm) product. Rail cars are dumped in the direction away from the crusher, and water sprays at the dumper level and in the rock boxes are used for dust suppression. There are two 72 in. by 19 ft (1.83 m by 5. 8 m) apron feeders under the 500 st cr'ushed ore pocket and two more under the grizzly undersize pocket. Feeder speeds are variable up to 72 fpm. Grizzly undersize is dropped to the feeder pocket by three shelves forming a rock ladder attached to the pocket walls. Each pair of apron feeders, one for crushed ore and one for grizzly undersize, discharge to a 72 in. (1. 83 m) picking belt for tramp removal; this belt feeds one of two 54 in. (1.37 m) feeder conveyors which in turn discharge to a 60 in. (1. 52 m) takeaway belt operating at 175-300 fpm (53.3 - 97.4 mpm). Both picking belts are equipped with metal detectors and tramp iron magnets, and a separate 30 in. (760 mm) conveyor is used to remove tramp material.

Jan 1, 1978

By G. W. Binkley, G. K. Dumbauld, F. A. Brooks, B. E. Morgan

In recent years, oil well cementing compositions have been developed with low densities, controlled set strengths, and satisfactory thickening times. With the introduction of the permanent-type well completion method for cementing wells, another property—that of rate of filtration or water loss to permeable formations— has become important. Laboratory data show that cement slurries prepared with oil, water, bentonite, and calcium lignosulfonate possess satisfactory thickening times, strengths, and filtration properties for primary cementing of casing and for squeeze cementing with the permanent-type well completion technique. Cementing compositions have been prepared with oil-in-water emulsions varying in composition from 60 cc water and 20 cc oil per 100 gm cement to 90 cc water and 45 cc oil per 100 gm cement. These compositions have contained from 0.4 to 5.0 per cent calcium lignosulfonate by weight of dry cement. Slurries prepared from these compositions weigh 11.4 to 13.1 lb/ga1 and have filtration rates of from 10 cc to approximately 100 cc in 30-min API tests at room temperature. The unfiltered emulsion cements develop one-day tensile strengths of 60 to 220 psi; and the filtered mass sets to tensile strengths of 60 to 150 psi in 12 hours and develops strengths of 320 to 515 psi in seven days when cured at 125° F. Field experience gained from 13 field mixing jobs demonstrates the utility of the emulsion cement for permanent-type squeeze cementing operations. INTRODUCTION In recent years, research in oil well cementing composition has been directed toward the development of cements having low densities, controlled set strengths, satisfactory thickening times, and low rates of water loss by filtration. Two well cementing compositions that have been developed with these properties are the modified cements containing, respectively, 12 and 25 per cent bentonite clay and various concentrations of calcium lignosulfonate1,2 In a search for other ways to incorporate these characteristics in a cementing composition, consideration was given to the rheological properties of oil-emulsion drilling fluids. Many of the desirable properties observed in oil-emulsion drilling fluids are equally advantageous in a cementing composition. For example, low water loss by filtration and low density, which are inherent characteristics of these oil-in-water emulsions, are desirable for many oil well cementing operations. Furthermore, oil-emulsion slurries have lubricating properties similar to those of oil-emulsion muds, a factor which should provide ease of rotation of casing during primary cementing operations. The properties of lubrication and low filtration may be of special value in both primary and squeeze cementing operations encountered in slim-hole drilling. Studies in the preparation of oil emulsion systems have pointed out the need for violent agitation in order to disperse the oil into the water phase. It was thought, therefore,

Jan 1, 1957

By Konrad Stern

The terms asphalt and bitumen have been applied interchangeably, although incorrectly on occasion, for centuries to various bituminous materials that were found in nature. Native bituminous materials of only the solid types, deposits of which are found on or near the surface of the ground, together with the principal asphaltic type petroleum bitumens will be considered in this chapter. The international dictionary compiled by the "Permanent International Association of Road Congresses" still gives the full name as "Asphaltic Bitumen" but of recent years the word "Bitumen" has been recognized as most appropriate and is defined by the American Society for Testing Materials as follows: "Mixtures of hydrocarbons of natural or pyrogenous origin, or combinations of both, frequently accompanied by their nonmetallic derivatives, which may be gaseous, liquid, semisolid or solid and which are completely soluble in carbon disulfide." Asphaltic pyrobitumens, as defined by Abraham,2 is a species of pyrobitumen, including dark-colored, comparatively hard and nonvolatile solids; composed of hydrocarbons, substantially free from oxygenated bodies; sometimes associated with mineral matter, the nonmineral constituents being infusible and largely insoluble in carbon disulfide. Deposits of native bituminous materials are found scattered over the entire world, but many are relatively unimportant as far as commerce is concerned. No attempt has been made to cover all of the known deposits. The principal bituminous materials of commercial interest are: 1. Native asphalts, solid or semisolid, associated with mineral matter such as Trinidad Lake asphalt, Rock asphalt and Selenitza, Boeton and Iraq asphalts. 2. Native Asphaltites, such as gilsonite, grahamite and glance pitch, conspicuous by their hardness, brittleness and comparatively high softening point. 3. Asphaltic bitumens obtained from nonasphaltic, semi-asphaltic and asphaltic crude petroleum by distillation, blowing with air and the cracking of residual oils. 4. Asphaltic pyrobitumens of which wurtzilite and elaterite are of chief interest industrially as they depolymerize upon heating, becoming fusible and soluble in contrast to their original properties in these respects.2 5. Mineral waxes, such as ozokerite, characterized by their high crystallizable paraffine content. Native Lake Asphalt At Brighton situated in the southwestern part of the Island of Trinidad is one of the largest deposits of native asphalt in the world.3 The lake is oval in shape, covering an area of 114 acres and having a depth of 285 ft at its center. The material forming this deposit is an emulsion of water and bitumen with a suspension of mineral matter consisting of impalpably fine clay dispersed by nature in the asphalt, and small quantities of silica and vegetable matter. The entire mass of asphalt is in slow but constant motion as evidenced by the migration of islands of vegetation from one place to an-

Jan 1, 1960

The Western World's gold reserves now exceed 23,000 mt (750 million oz), 65% of which exist in South Africa. Although several major mines are reducing production or closing because of depletion of reserves, new mines or expansions of existing mines are coming on-stream which will maintain an annual production of 684 mt (22 million oz) of gold well into the 1990s. These new operations by the South African mining industry represent the largest expansion since the opening of the Witwatersrand gold fields in 1886. Included in three new mines being opened is that of Anglo American Corporation's Elandsrand plant, their fir& new gold venture in South Africa in seventeen years. Current average grade of South African mines is 8.2 g Au per mt (0.24 oz per st); and while the cost of the Elandsrand 135,000 mt (149,000 st) operation, including mine development, was about $314 million, it is estimated that the cost of a comparable operation started today and completed in the mid-1980s would be of the order of $480 million. New mines to exploit low-grade ore bodies are, therefore, likely to be few in number, and further expansion will undoubtedly be in the form of extensions to existkg operations where cash flow can be used to finance development. The authors' first monograph, "Gold and Silver Cyanidation Plant Practice," devoted a section to South African cyanide plant operation; and it is believed that this new volume would not be complete without a description of Elandsrand, South Africa's newest gold plant. The Elandsrand mine is adjacent to Anglo American's Western Deep Levels on the Far West Rand. The decision to go ahead with the development was taken in mid-1974 from the results of exploration drilling carried out over a period of .lo years. Results of 17 bore holes and 68 intersections of the Ventersdorp Contact Reef had indicated a gold-.bearing reef less than one meter thick at a depth of 1,800 to 3,000 meters (5,900 to 9,840 ft). Preliminary studies indicated a mine of 900 km (560 miles) of underground workings would yield 725,000 kg (23. 3 million oz) of gold from 60 million mt (66 million st) of ore to be milled over a period of 34 years. Eventually, when the mine is in full production, the total hoisting capacity will be 300,000 mt per month (331,000 st) for a milling capacity of 225,000 mt per month (248,000 st). The Elandsrand surface facilities have been built on a low range of 0 hills to take maximum advantage of the 10 slope in transporting ore

Jan 1, 1981

By Harold Vagtborg

Equilibrium vaporization ratios were obtained for light hydrocarbons, nitrogen, carbon dioxide, and hydrogen sulfide in a reservoir fluid containing 35 mole per cent hydrogen sulfide. The data cover the range from 700 to 2500 psia at 154°F. The results of this study are compared with results obtained by other investigators on systems containing less hydrogen sulfide. When large amounts of hydrogen sulfide are present, the equilibrium vaporization ratios for ethane and heavier hydrocarbons are greater than the ratios for systems containing little or no hydrogen sulfide. Large amounts of hydrogen sulfide have the reverse effect on the ratios for methane. Routine PVT studies were performed on the reservoir fluid including flash and differential liberations of the dissolved gas. The pressure-volume relationships of the saturated fluid were also determined. It is shown that the use of published correlations on physical properties of reservoir .fluids can lead to gross errors when applied to systems containing large amounts of hydrogen sulfide. INTRODUCTION Equilibrium vaporization ratios for various components in naturally occurring crude oil and condensate systems have been reported in the literature.1,2,3,4 Recently, several papers have been published with emphasis on non-hydrocarbon components such as nitro- gen, carbon dioxide and hydrogen sulfide.5,6,7,8,9 The increased discovery of reservoir fluids having high concentrations of these non-hydrocarbon components, particularly hydrogen sulfide, has created a need for a further study of their phase behavior. Equilibrium vaporization ratios are known to vary with pressure, temperature, and overall composition of the system.'" It was anticipated that ratios for systems containing large amounts of hydrogen sulfide would differ from the ratios for systems containing small amounts of hydrogen sulfide. Therefore, the present work was undertaken in order to obtain reliable equilibrium vaporization ratios for the reservoir-fluid in question. PROCEDURE The procedure followed was evolved after considerable experimentation on methods of handling the very sour crude. It was found that drying agents (e.g. CaCl2 and CaSO4) absorbed an appreciable amount of hydrogen sulfide from the gas used to prepare the recombined samples. The concentration of hydrogen sulfide dropped as much as 10 mole per cent in a single pass through a 3-ft drying tube. It was also found that when undried gas was agitated with mercury in the PVT cell, a black scum, believed to be mercuric sulfide, was formed and the hydrogen sulfide content of the gas dropped several mole per cent. Because composition changes during a run could not be tolerated, separation of the mercury and sour fluid was necessary. In order to effect this separation, a stainless steel piston, equipped with Teflon O-rings, was placed in the PVT cell between the mercury and the sour fluid. This piston had to be constructed in three parts because

Jan 1, 1955