Search Documents

By G. H. Tausch, J. R. Dublin, T. A. Huber

Simplified equipment and techniques have been developed to permit cementing a completion interval in a well and recompleting higher, lower, or at the same depth in such a manner as to: 1. Eliminate the need for a conventional drilling or workover rig. 2. Eliminate mud and other cement contaminants which have long interferred with ideal cementing. 3. Eliminate need for drilling out cement. 4. Provide a more satisfactory recompletion. 5. Provide a more economical recompletion. This technique involves the use of a small-diameter, lightweight, tubing extension which is run on a wireline and set in a landing nipple previously installed in the tubing string. Low squeeze pressure and small cement volumes, with their attendant cost reduction, are successfully used when wells are completed and reworked with salt water or other penetrating fluids. Relatively low-water-loss cement is an integral component of the technique which provides that excess cement be reverse-circulated from the well to leave the casing void of cement when recompleting lower or in the same interval. Substantial cost reductions are realized by using the simplified or low-pressure cementing technique, and the ratio of successful squeeze-cement operations has been increased. Squeeze-cementing or recementing is the act of filling a channel behind casing or filling holes purposely placed in the casing. To obtain a satisfactory squeeze-cement job, it is necessary only to fill the channel or the perforation holes with a cement filter cake and to allow it to harden in that position. In the past, the presence of mud in a well has been considered the chief deterrent to obtaining a good cement bond and satisfactory cement job; however, late developments in squeeze-cementing have made it possible to eliminate cement contamination or interference. Since it is possible to form a cement filter cake with a small pressure differential, squeeze-cementing with high pressures may not be necessary in most cases. The amount of cement needed to fill the annulus about the casing and even to fill part of the casing, if necessary, is generally small in quantity. Use of low squeeze-cementing pressures and small quantities of cement provides the following advantages: 1. Longer effective life of well tubing, casing, and other equipment; and less chance of costly equipment failure due to excessive pressure. 2. Monetary savings effected by elimination of retainers and specal squeeze-cementing tools. 3. Monetary savings effected by use of small quantities of cement and fewer squeeze-cementing operations. 4. Future surface squeeze-cementing equipment may be smaller and more economical to operate and maintain.

Jan 1, 1955

By Gerhard Derge

Metallurgists have used borax as a fluxing agent traditionally, but until recently elemental boron has played an insignificant role as an alloying element. Neither the metal nor its compounds have been regarded as important metallurgical materials and there is a surprising lack of knowledge concerning their metallurgical behavior. The new applications to steel-making of both boron and borates, which arose in part from wartime incentives and restrictions, have been seriously handicapped by this lack of data. For example, rasorite, a naturally occurring sodium borate, has been shown to be an effective substitute for aluminum as a ladle deoxi-dizer in rimming steels.' Likewise, the effectiveness of boron as an alloying agent has been demonstrated,2,3 giving deep hardening when used in restricted amounts. The exploitation of both of these uses has been retarded by the difficulty of attaining suitable metallurgical control. Recognizing that the most important information required was a knowledge of the equilibrium between boron and oxygen dissolved in liquid iron. Gurry4 calculated this relation from the best thermal data available. However, estimates of the entropy of melting of boron, the activity coefficient of boron in liquid iron and the activity coefficient of B2O3 in slag were involved, and experimental work on this problem was obviously desirable. The experiments to be described were planned to establish the boron-oxygen relations in liquid iron and to demonstrate at the same time the ferroborate slag compositions in equilibrium with various amounts of oxygen in liquid iron. Accordingly, slags containing varying proportions of iron and boron oxides were held in contact with molten iron, and samples of both slag and metal were analyzed. The limitations upon the accuracy of the data will be considered, but in a practical sense the oxygen levels that can be attained in iron by iron borate slags, and the amounts of boron in iron at these oxygen levels were established. Experimental Procedure No entirely suitable refractory was found for the mixtures of iron oxide and boron oxide used as slags. Crucibles of silica, magnesia, Ramix, beryllia, and zirconia were all tried unsuccessfully. The must satisfactory method discovered for handling them was the rotating-crucible technique, which creates a parabolic crucible of liquid iron.5,6 Even this was not entirely successful, for at steelmaking temperatures (1600°C.) the slags had such a low surface tension that they crept up to the refractory and slowly dissolved it. These difficulties made it impossible to maintain a constant slag composition for an unlimited period Of time. However, by using the rotating technique, short runs could be made in

Jan 1, 1947

By Gerhard Derge

Metallurgists have used borax as a fluxing agent traditionally, but until recently elemental boron has played an insignificant role as an alloying element. Neither the metal nor its compounds have been regarded as important metallurgical materials and there is a surprising lack of knowledge concerning their metallurgical behavior. The new applications to steel-making of both boron and borates, which arose in part from wartime incentives and restrictions, have been seriously handicapped by this lack of data. For example, rasorite, a naturally occurring sodium borate, has been shown to be an effective substitute for aluminum as a ladle deoxi-dizer in rimming steels.' Likewise, the effectiveness of boron as an alloying agent has been demonstrated,2,3 giving deep hardening when used in restricted amounts. The exploitation of both of these uses has been retarded by the difficulty of attaining suitable metallurgical control. Recognizing that the most important information required was a knowledge of the equilibrium between boron and oxygen dissolved in liquid iron. Gurry4 calculated this relation from the best thermal data available. However, estimates of the entropy of melting of boron, the activity coefficient of boron in liquid iron and the activity coefficient of B2O3 in slag were involved, and experimental work on this problem was obviously desirable. The experiments to be described were planned to establish the boron-oxygen relations in liquid iron and to demonstrate at the same time the ferroborate slag compositions in equilibrium with various amounts of oxygen in liquid iron. Accordingly, slags containing varying proportions of iron and boron oxides were held in contact with molten iron, and samples of both slag and metal were analyzed. The limitations upon the accuracy of the data will be considered, but in a practical sense the oxygen levels that can be attained in iron by iron borate slags, and the amounts of boron in iron at these oxygen levels were established. Experimental Procedure No entirely suitable refractory was found for the mixtures of iron oxide and boron oxide used as slags. Crucibles of silica, magnesia, Ramix, beryllia, and zirconia were all tried unsuccessfully. The must satisfactory method discovered for handling them was the rotating-crucible technique, which creates a parabolic crucible of liquid iron.5,6 Even this was not entirely successful, for at steelmaking temperatures (1600°C.) the slags had such a low surface tension that they crept up to the refractory and slowly dissolved it. These difficulties made it impossible to maintain a constant slag composition for an unlimited period Of time. However, by using the rotating technique, short runs could be made in

Jan 1, 1947

By M. Cohen, W. J. Harris

The recent application of lineal analysislt2 to the austenite-martensite reaction has made possible a quantitative study of the kinetics of this transformation during rapid cooling. Martensite range curves can thus be constructed to portray the onset of the reaction at Ma and its subsequent progress as a function of temperature down to and below the ambient. It now seems in order to investigate other aspects of the martensite transformation, using this quantitative method of approach. One of the least understood characteristics of the austenite-martensite reaction is that of stabilization which has been defined by Troiano and Greninger3 as 'la lowering of Ma, resulting from aging, without change in chemical composition of the parent solid solution." In other words, if the hardening quench is arrested at a predetermined subcritical temperature (TA) for a sufficient period of time, more austenite may be retained at a given lower Or reference temperature (Tr) than if the steel had been cooled directly and rapidly to Tr in the first place. For the purposes of the work at hand, the extent of stabilization produced by the isothermal treatment at Th is measured explicitly in terms of the excess austenite (6) that exists in the steel at T,, over and above the amount that is normally present after direct quenching to T,. T, is conveniently taken to be room temperature, but this choice is not essential and is sometimes undesirable. The holding temperature (TA) may be above or below M,, and still cause stabilization depending upon the themistry of the austenite. stabilization has been found to occur in the presence of bainite4 and of martensite6,6,7,8 as well as in the absence of either,g The phe-nomenon of stabilization is not concerned with (and may even be obscured by) ferrite formation or any other type of phase change occurring at T~ that alters the chemistry of the remaining austenite. Such a structural change would obviously influence the martensite transformation during subscquent cooling. Stabilization, however, is more subtle; it appears to manifest itself without detectable variation of the austenite composition, whether in the presence or absence of transformation products. There are relatively few direct references to stabilization in the literature. The stabilizing effect of room temperature aging and tempering on the subzero transformation of retained austenite has been clearly shown in plain carbon,6,8 low alloy6s7.8 and high alloy tool steels.10'5 ssa- with the as-hardened steel, the degree of stabilization increases with tempering time and temperature through

Jan 1, 1949

By W. H. Ashby, R. W. Cassingham, C. R. Blomberg, J. B. Justins

The Brookhaven field is one of several Basal Tuscaloosa reservoirs located in south-central Mississippi. It is a standstone reservoir, of erratic deposition and with several faults, having an approximate subsea depth of 9,800 ft. A large variation in permeability exists with a weighted average being 256 md. Estimated average interstitial water saturation is 45 per cent. The undersaturated reservoir fluid exhibits marked differences in physical properties with measured saturation pressures ranging from 733 to 2,255 psi. Early rapid decline in reservoir pressure caused the operating interests to unitize the field and initiate a program of pressure maintenance by gas injection. At the time gas injection was commenced, the reservoir pressure had fallen to nearly half of the original pressure with only 4.5 Per cent of the original oil in place produced. The reservoir pressure has since been maintained at approximately 2,750 psig, and cumulative production to date is 17 per cent of original oil in place. An analysis of field performance during gas injection is presented in detail. The program of pressure maintenance by gas injection is considered to be a success, since the expected ultimate recovery has been increased and the current production rate is in excess of 2 per cent of original oil in place per year. Performance has been better, anticipated ultimate recovery is larger, and total production costs are lower than for a similar Basal Tuscaloosa reservoir nearby, even though that field appears to have a more effective natural water drive. INTRODUCTION The history of the Brookhaven Unit is a testimonial for unitization and for the application of engineering techniques in the operation of an oil field. The operating and royalty interests in this field have mutually benefited from their early recognition of the need for unitization and pressure maintenance and from the forthright manner in which these were accomplished. The tangible benefits accruing to the participants in the Unit are: (1) income from gasoline plant products, (2) reduced lifting and operating costs from those of competitive operation, (3) maintenance of high levels of current income by mitigation of the inevitable decline in production rates inherent to natural depletion, (4) an increase in ultimate recovery of about 40 per cent over natural depletion operations. This paper should properly be considered a progress report; however, the performance of the field after five years of pressure maintenance clearly indicates that the ultimate success of the project is assured. LOCATION AND GEOLOGY The Brookhaven field is located in south-central Mississippi, about six miles from the town of Brookhaven. Production at Brookhaven

Jan 1, 1955

By V. F. Leferrer

A new process for the treatment of silver crusts from desilverization of lead has been developed by Societe de Penarroya. The zinc contained in the crusts is recuperated by vacuum distillation at low temperature. The use of special retort crucibles is avoided. AT Noyelles-Godault the Parkes process (zinc addition to a silver-bearing lead melt) is used to desilverize lead bullion from the blast furnace. The crust which rises to the surface of the bath is removed and pressed by a well-known process in a press of the Howard type. The pressed crust, called zinc crust or silver crust, contains 10 pct Ag, 30 pct Zn, and 60 pct Pb. It is melted under a salt bed in a small, narrow, and deep kettle heated only in its upper part. A liquid concentrated alloy is obtained which is called T.A.C. in France (triple alliage concentr6) analyzing approximately 25 pct Ag, 65 pct Zn, 8 to 10 pct Pb, and 1 to 1.5 pct Cu. This T.A.C. is a real metallic alloy, completely deoxidized, and can be stored indefinitely. The process used at Noyelles-Godault consists in distilling this alloy in a tight furnace, under low vacuum and at low temperature, so that only the zinc distills and is condensed into liquid form. The residual silver-bearing lead is almost entirely free from zinc and oxidized dross. The vacuum dezincing equipment, see Figs. 1 and 2, consists of: 1) A furnace, constituted of a casing of steel plate lined with refractory bricks, heated internally by means of graphite resistors. The temperature of the furnace is measured by a thermocouple device and controlled by an automatic temperature regulator which acts upon the flow of the current passing through the resistors. Two doors, numbered 1 and 2 in Fig. 2, are provided for, one for charging the T.A.C., the other for tapping the high silver-bearing lead. 2) A condenser, and an ordinary room lined with good heat conductor refractory material. This condenser is provided with a graphite resistor which serves to bring to temperature when starting the furnace. A thermocouple records the temperature of the zinc melt and controls the temperature in the furnace, that is, the flow of current through the resistors, by means of the above mentioned regulator, so that the distillation rate in the furnace does not exceed that of the condensation. The condenser is connected to the vacuum pump by a filter. The whole equipment should, of course, be fluid-tight. The operation is carried out under a vacuum of about 10 mm Hg.

Jan 1, 1958

By M. E. Wadsworth, I. B. Cutler, R. W. Bartlett

The oxidation kinetics of ZrC was studied between 450" and 580°C in oxygen pressures from 6.5 x 10-to 1 atm using a ther mogravimetric apparatus and sized powder samples. Two parallel rate controlling processes were observed. A surface reaction occurring at the ZrC-ZrO2 phase boundary accounted for most of the oxidation and had an activation enthalpy of 46 kcal per mole. The other process, believed to be diffusion of oxygen into the ZrC lattice partially replacing carbon, had an activation enthalpy of 53 kcal per mole. The enthalpy for chemisorption of O2 on ZrC was determined to be —13 kcal per mole. Water vapor in the presence of oxygen accelerated the surface reaction rate. THERE has been little reporting of formal rate studies or attempts to ascertain the mechanism of oxidation of carbides. MacDonald and Ransley1 studied the oxidation of titanium carbide which has the same structure as zirconium carbide, fcc. They observed an initial increase in rate with increasing temperature followed by a rapid decrease through a rate minimum and a subsequent second increase at higher temperatures. The discontinuity in the rate rise was attributed to a phase change in the oxide which changed the rate determining step from the surface reaction at the carbide-oxide interface to diffusion through the oxide layer. Samsonov and Golybera 2 studied titanium carbide and reported that during the initial period of oxidation a dense film of Tic-TiO was formed followed by the formation of less adhering layers of higher oxides. The purpose of this investigation was to study the kinetics of oxidation of zirconium carbide and to attempt to gain some knowledge of the mechanism by which oxidation occurs. EXPERIMENTAL PROCEDURE Measurement of the weight gain associated with the oxidation of ZrC was used to determine oxidation rates. The principal experimental parameters were surface area, temperature, and oxygen pressure. Although moderately sized crystals of ZrC can be grown by the Van Arkel method, the only commercially available ZrC is a powder. In using powders, the surface area must be controlled either by fabricating the powder into a sintered pellet with a measurable surface area, relatively fixed during oxidation, or by using sized unconsolidated powder and applying appropriate geometric considerations to the shape of the grains to correct for their diminishing surface areas as they oxidize. Both techniques involve some difficulties. pellets of binder-free zirconium carbide can be made by hot pressing, but it is difficult to obtain densities greater than 90 pct of

Jan 1, 1963

By Carl F. Floe, Michael B. Bever

TRE solubility of hydrogen in molten copper-tin alloys is of both practical and theoretical interest. From a practical standpoint, data on the equilibrium solubility as a function of temperature, pressure and alloy composition are valuable for a better understanding of porosity problems in bronze castings. From the theoretical point of view the determination of the hydrogen-copper-tin equilibrium is of interest since it extends the laws governing the solution of gases in metals. This paper presents the results of an investigation of the solubility of hydrogen in representative compositions of the copper-tin system at temperatures ranging from above the liquidus to 1300°C. and at pressures from less than 50 mm. of mercury to about atmospheric. REVIEW OF PREVIOUS WORK The solubility of hydrogen in copper was determined by Sieverts and Krumbhaarl in 1910 and by Roentgen and Moeller2 in 1934. Their values are in fair agreement. In 1926 Iwasé3 reported results that were very much higher. The published data on the solubility of hydrogen in tin do not agree. Smithells4 states that no reliable data are available. According to Sieverts and Krumbhaar,5 hydrogen is insoluble in tin. Bircumshaw,6 on the other hand, found a definite solubility at 800°C. The latter's experimental procedure did not provide for stirring of the metal and in his opinion he failed to reach equilibrium. Iwasé3 again reported large solubility values. For copper alloys, Sieverts and Krumbhaar6 distinguished between alloying elements that do not markedly affect the solubility of hydrogen, elements that increase the solubility, and elements that reduce it. They named gold, tin, and aluminum as examples of this last group and reported hydrogen solubility data at 1225°C. for the copper-rich side of these alloy systems at atmospheric pressure. Without giving experimental results, they stated that the amount of hydrogen dissolved by liquid copper alloys is proportional to the square root of the pressure as in pure metals. These authors suggested that in a limited way the effect of an alloying element on the solubility of a gas is related to the constitution diagram for the alloy system. Sieverts7 also called attention to the fact that the curve of hydrogen solubility versus composition of copper-tin alloys shows a sharp change of direction at the composition of Cu3Sn and suggested that this compound persists at least to some extent in the molten state. Iwas3é reported large hydrogen solubility values for several compositions of copper- tin alloys, which appear to be in error.

Jan 1, 1944

By D. B. Jugle, J. B. Darby, O. J. Kleppa

A systematic study has been made of the kinetics of solution under steady state, dynamic conditions of titanium, vanadium, chromium, iron, cobalt, and nickel in liquid aluminum. It was found that the temperature dependence of the solution rate obeyed an Arrhenius-type rate equation, and that at a given temperature the rate of solution of the various solutes correlates quantitatively with the equilibrium solubility of the solute in liquid aluminum. These results are consistent with a mechanism where the rate-controlling step is the diffusion of solute atoms through a liquid boundary layer. THE present study was initially started in order to explore the feasibility of liquid-metal solution calorimetry for transition metals and alloys. Previous work1 in this field employing liquid tin as a solvent at temperatures in the 500' to 600' range had indicated that the rates of solution of most transition metals in tin are very low. Under such conditions effective solution calorimetry is difficult. The objective of the present investigation was two-fold: a) To obtain, as far as possible, quantitative data on the rates of solution of a series of transition elements in liquid aluminum. b) To explore whether liquid aluminum might be a suitable solvent for liquid-metal calorimetry. In the course of this work a comprehensive set of data was obtained on the steady state rates of solution of transition metals in a common liquid-metal solvent. The results are consistent with the boundary layer model, which assumes that the rate-controlling step consists of diffusion of solute atoms through a viscous liquid layer. EXPERIMENTAL PROCEDURE A vacuum-tight stainless steel vessel was surrounded by a resistance furnace, as shown in Fig. 1. In all experiments the temperature of the liquid solvent was controlled to 2.5' by means of a Micromax controller. A high-vacuum manifold connected to the vessel maintained a vacuum of 1 x 105 mm of Hg or better. The vacuum vessel was equipped with a charging section isolated from the working chamber by a vacuum-tight gate valve. This arrangement allowed the specimen holder to be removed or inserted into the apparatus without removal of the liquid metal bath. The specimen holder was suspended from a closed end stainless steel tube, which also served as the thermocouple protection tube. The portion of the tube that was below the solvent level was surrounded by an alumina protection tube to isolate it from the liquid metal bath. The stainless steel tube was connected through a rotary vacuum seal and a gear train to a fractional horsepower motor. For most experiments the tube was rotated at a constant

Jan 1, 1963

By John Brown

As a part of a symposium on the relations of structure to ore deposi-tion, in February 1938, the writer presented some tentative opinions derived from his experience with a number of important lead-zinc replace-ment deposits. These ideas were set forth, as a basis for discussion and a stimulus to further inquiry, in a mimeographed leaflet that read as follows: Intimate acquaintance with a number of lead and zinc deposits in metamorphosed limestones seems to indicate the existence of certain common features from which can be established some general principles governing the localization of ore in this type of formation. It is suspected that these principles can be applied, with modifica-tions, to mineralization in unmetamorphosed limestone. In metamorphosed forma-tions, some observed rules are as follows: 1. Bands or masses of pure limestone are very resistant to replacement by ore solutions, and are likely either to contain no ore or to resist replacement until near the end of mineralization. The reason for this apparently is physical, not chemical, since microscopic data indicate that when ore is deposited by far the greater part of it substitutes for carbonate. The chief factor is believed to be a lack of porosity in massive limestone that has undergone flowage and recrystallization. 2. Masses of intensely siliceous or silicated rock are likewise unfavorable ore receptacles. This seems to be accounted for by two factors: (a) chemical unsuit-ability or resistance to replacement, and (b) physical resistance to small-scale brecci-ation, which might facilitate the opening of effective channelways for solutions. Some low-grade ore may occur, however, and also sporadic fracture fillings. 3. The optimum condition for ore reception appears to be found in bands or areas containing carbonate and silicates (or quartz) intimately mingled in something like equal proportions. In this situation movement is likely to result in mixed flowage and fracture, producing a fine-textured porosity that admits solutions freely and provides access to an abundance of replaceable carbonate. Cleavage cracks in some minerals such as diopside are believed to facilitate the penetration of solutions. 4. Certain minerals or assemblages are regarded as favorable impurities in a lime-stone and others as unfavorable. Original quartz, and subsequently developed diopside, and perhaps garnet, are typical favorable pre-ore gangue; in general rather equidimensional, brittle minerals. Tremolite, biotite, and probably wollastonite, are typical unfavorable pre-ore gangue; in general highly elongated and somewhat flexible minerals likely to develop under strong shearing stresses. 5. Tentative opinion is that the ratio of lime and magnesia in a limestone-is of little or no importance.

Jan 1, 1940

By G. Thodos, E. M. Phillips

A reduced density correlation for the gaseous and liquid regions of ethane has been developed from all the experimental PVT data available in the literature for this substance. Saturated vapor and liquid densities reported for methane, propane and n-butane were utilized to establish the rectilinear-diameter line for ethane. This line was then used with the saturated-vapor data for ethane to produce the saturated envelope for this substance. Most of the saturated liquid data reported for ethane were found to be inconsistent with the saturated-liquid curve resulting from this study. The correlation covers the regions 0.65 < TR <6.0 and 0 < PR < 15. For regions for which no experimental data have been reported, the isobars of the correlation were extended by the use of the theorem of corresponding states. This correlation is presented both on rectilinear and log-log coordinates. INTRODUCTION At the present time, there is considerable interest in the exact PVT behavior of pure hydrocarbons. Matschke and Thodos12 recently have developed a comprehensive compilation of experimental vapor and liquid density data for methane. Similar studies have been conducted for other pure substances.4, 7 In the present study the density data available in the literature for gaseous and liquid ethane have been critically reviewed and utilized to develop a reduced density correlation for this substance. SATURATED LIQUID AND VAPOR DENSITIES The rectilinear-diameter rule proposed by Cailletet and Mathias5 states that the sum of the saturated liquid and vapor densities of a pure substance is a linear function of temperature which passes through the critical point. This law, although empirical, has been well established by continued verification since its conception in 1886. This rule has been applied to the saturated density data of methane,6 propane 17 and n-butane8 to produce the straight lines presented in Fig. 1 which pass through the critical point TR = 1.00, Pr = 2.00. The rectilinear-diameter relationship for ethane was established from the lines for the other substances in Fig. 1 by plotting the quantity p~, + PR against zc for different reduced temperatures. A critical analysis of the saturated vapor and liquid densities reported for ethane by Kuenen,10 Maass and McIntosh,11 and Sage, Webster and Lacey18 revealed that the values of PR1 + pr resulting from these studies were inconsistent with the rectilinear-diameter line obtained from the reliable density data of the other substances, as shown in Fig. 1. In the analysis of these data, reduced quantities were calculated using the critical con-

By C. G. Dunn, J. L. Walter

The c/laracterzstics of cube-oriented nuclei ard other matrix grains that are associated with secondary, recrystallization to the cube texture in high-purity silicon iron were investigated by me-tallographic and X-ray methods. The results show that the structure consists of relatively perfect grains of average diameter between one and two times the sheet thickness ad that the texture has a moderately strong (110) [001] component and a weak (100) [001] component. The results also indicate that matrix stability results from the two-dimensional nuture of the graitzs and that cube-orzented nuclei are neither more Perfect nor larger grains than other matrix grains but have a preferred [001] direction in the rolling direction and have a more effective driving force for growth than other grains because of a low (100) surface energy. THE structures and textures of fine-grained rnatrices determine to a large extent the kinds of secondary recrystallization textures that form on annealing. The understanding of secondary recrystallization processes therefore depends on adequate information about the initial matrices. Matrices usually have three characteristics: 1) they consist of fine-grained primary recrystallization structures, 2) the fine-grained structures are stable toward normal grain growth, and 3) they contain secondary recrystallization nuclei. Stability toward normal grain growth may be due to either a strong single orientation texture (texture inhibition)&apos; or a dispersed second phase (dispersed phase inhibition).2"4 If normal grain growth is not inhibited by either of these two factors, it nevertheless stops when the average grain size is between one and two times the sheet thick- ness.5 This thickness effect satisfies one of the characteristics of a matrix for secondary recrystallization. Its importance in the development of the cube texture in high-purity silicon iron by secondary recrystallization was pointed out by the authors in a recent paper on tertiary recrystallization7 and will be discussed further in the present paper. Assmus, Detert, and he8 have provided some information on a matrix for secondary recrystallization to the cube texture in silicon iron. They found a (110)[001] or Goss texture with enough spread about the rolling direction to include a small amount of the (100)[00l] orientation. The distribution of the [00l] directions was strongest parallel to the rolling direction for both (100) primaries and cube secondaries. These authors found no correlation between size of a matrix grain and orientation and concluded that some property other than size must be the distinguishing characteristic of the cube-oriented nucleus. No consideration was given, it

Jan 1, 1961

Book Review MAN-TO-MAN: THE STORY OF INDUSTRIAL DEMOCRACY. By John Leitch, Phila¬delphia, Pa. The B. C. Forbes Publishing Co., New York, 1919, 2.19 pp., 7 1/2 X 5 in. $2.00. "Man to Man" is a short, well-written, well-printed, easy to read and very interesting hook. It is an account of a method introduced into more than twenty industrial plants to give the workers a share in managing their own troubles. It is not a panacea for labor troubles and strikes, but neither have existed where the new method has been tried. The scheme is, in a word, to organize the working force like the government, having a cabinet composed of the executives, a senate composed of foremen, and a house composed of men elected by fellow workers from all departments. This governing machinery takes up all complaints of workers, investigates, reports, and settles. The increased profits due to economy and increased production from this cooperation are divided 50-50 between the company and the men. Experience has shown that, since inattention, tardiness, irregularity, and inefficiency tend to reduce their profits, all men very quickly, after once convinced of the sincerity of the management in their scheme of cooperation, eliminate them because it is for their personal profit. Astonishing results have been attained, including higher wages, greater output, lower unit costs, great reduction in labor turnover, elimination of waste, an increased loyalty and a waiting list of employees even in periods of labor shortage. Profit sharing as such and stock ownership as a benefit to industrial relations are discussed briefly and illuminatingly, although they are not believed by the author to he the best way to bring about the human relation between those who work,for and those who work with money. The author is not against unions but does not believe the union is the best medium for improving industrial relationship. The look is nowhere dogmatic but is always forceful and convincing and, being well written, is very entertaining. It is doubtful if "Industrial Democracy" is the right expression for the solution of the problem but certainly anything that will place on the shoulders of labor some of the responsibility of industry and will increase production is tine much-to-be-desired desideratum. It is a. contribution to the solution of our biggest problem and should be read by everyone who employs men and who has been worried by the labor turnover. P. E. B.

Jan 7, 1919

By Mark Sheppard

DURING the winter of 1937, the writer visited a West Virginia stone quarry at which the overburden is stripped hydraulically. The quarry is in a bed of limestone, about 200 ft. thick, which outcrops on a hillside above a small river; the quarry face is 175 ft. high. The top of the stone is cut in all directions by erosion channels, which are filled with a tough, red clay. Some of the larger channels are 30 ft. deep and 8 ft. wide. The thickness of the clay overburden ranges from a few inches to 10 ft., the average being estimated as less than 3 feet. The topography of the district is rugged, and the hillside above the quarry face is not suited to the use of the usual mechanical methods of moving dirt. Until hydraulicking was started 10 years ago, the over- burden was dug by hand labor, dumped to the quarry floor and transported to the dump in quarry cars. Cleaning deep channels was a slow and expensive process. When hydraulicking was started, the top of the quarry face was over 200 ft. above the level of the river. The pipe line was carried in a semi- circle around the top of the quarry about 200 ft. from the face and about 50 ft. above it. As there is no adequate supply of water above the quarry, the water must be pumped from the river. As quarrying progressed the pipe line was moved until the discharge points are now over 300 ft. above the river. Water is pumped from the river by a four-stage centrifugal pump having a 5-in. intake and a 4-in. discharge. It is direct-connected to a 200-hp., 2300-volt, 1760-r.p.m. induction motor. At 1760 r.p.m. the rated capacity of the pump is 750 gal. per minute under a head of 600 ft. The pump is installed in a house of frame construction on the river bank, about 10 ft. above normal water level, which also houses the pump for the mill-water supply. Above the pumps are hoisting bays into which the motors are raised whenever the river reaches flood stage. An 8-in. suction line, equipped with a strainer and a foot valve, takes the water from a concrete sump at the edge of the river. The pipe line from the pump consists of 1750 ft. of 8-in. spiral steel flanged pipe and 800 ft. of 4-in. spiral steel flanged pipe. The connection from the pump

Jan 1, 1938

By Richard McCaffery

THERE has been some discussion among blast-furnace operators regarding the relative merits of tuyeres of the converging type and tuyeres designed in an attempt to produce a diverging jet of air. An article1 on Progress in German Blast Furnace Practice indicates the interest in this subject abroad. This article illustrates a diverging type of tuyere which is shown here in Fig. 1A. The design appears to be rather poor as regards known properties of air flow. The adoption of this. tuyere, the article states, resulted in a decrease of blast pressure of about 4 lb. per sq. in. and an increase of the output of the furnace. If the improvements mentioned are due entirely to the change in tuyere design, the subject of tuyere design seemed worthy of investigation and this paper is a report of such work. Because of the gain in efficiency brought about by the use of a diverging tuyere in the German plant, it was thought desirable to investigate the shape of the air streams issuing from various-types of tuyeres to ascertain whether the gain was due to the tuyere itself or to the distribution of the air in the furnace. Since it is difficult to do experimental work on a full-sized furnace, or even on full-sized tuyeres, and because of the equipment available for the work, it was decided to carry out the work on scale models of tuyeres. Therefore, in this work, single tuyeres were used and the blast discharged into the atmosphere. The shape of the air stream was determined by means of a Pitot tube suitably supported in the air stream at various positions. The air was. furnished by a Roots blower driven by a 10-hp. direct-current motor having field control, and capable of discharging 250 cu. ft. per min. with a pressure on the discharge of 4 in. of mercury. A modern blast furnace with 21-ft. hearth requires about 50,000 cu. ft. per min. of free air at from 16 to 23 lb. per sq. in. pressure, depending upon the type of burden. This pressure is the total pressure required to force the air through the burden and through the tuyeres. Upon computation the pressure drop through the tuyeres is about 1 to 2 lb. per sq. in. By making the tuyeres to a one-fifth scale, and by using a pressure of 1.5 in. of mercury, the shape of the air streams should be

Jan 1, 1931

By C. E. Berry

Natural stone or manufactured porcelain pebbles are used as the grinding elements in pebble mills and the mills are lined with stone or porcelain blocks. Steel balls usually form the grinding medium in ball mills, and the mills may be lined with steel. Pebble mills are used to avoid contamination by metal of the material being ground, to avoid rapid wear due to corrosion, and for other specialized reasons. Belgian silex (silica) blocks formerly were used widely for lining pebble mills, because of their good resistance to wear, light color, and low cost, but the importation of these blocks was suspended early in the war. The stocks of Belgian silex diminished so rapidly that it was found desirable to compare the properties of a number of domestic substitutes for use in critical operations. Accordingly, a study was made to determine the best substitutes for fine grinding of white pigment and for certain heavy-chemical process work such as the disintegration of phosphate rock in weak phosphoric acid solution. A comprehensive survey of substitute lining materials was not contemplated. It was stipulated at the beginning of the investigation that only materials on the market, available in large quantities, would be tested and that these should be reasonable substitutes from a a ance viewpoint as determined from known physical characteristics. Marble and limestone, for example, could be eliminated immediately. Quartzite, granite and porcelain were selected as likely substitutes for Belgian silex and were subjected to quality tests. Materials Tested 1. Belgian Si1ex.—Sample blocks of a standard grade were taken from crates in which they had been imported. The stone was light gray in color and contained inclusions of small clusters of quartz crystals as well as light colored portions that might be calcite. This was a siliceous rock which appeared to be of igneous origin. 2. Quartzite.—Samples of quartzite were obtained from a quarry in Minnesota. The blocks exhibited a crystalline fracture. The stone was pink in color and composed of fine quartz crystals bound together with a siliceous cement. 3. Granite A was a fine-grained granite quarried in South Carolina. 4. Granite B was coarse-grained granite quarried in South Carolina. 5. Granite C was a coarse-grained granite quarried in North Carolina. 6. Porcelain A.—Sample blocks of the pebble-mill lining material were obtained direct from the manufacturer. It was white in color and of lower specific gravity than the natural materials. It did not have a crystalline structure. 7. Porcelain B.—Sample pebble-mill lining blocks of the porcelain were received direct from the manufacturer. It was white

Jan 1, 1948

By C. E. Berry

Natural stone or manufactured porcelain pebbles are used as the grinding elements in pebble mills and the mills are lined with stone or porcelain blocks. Steel balls usually form the grinding medium in ball mills, and the mills may be lined with steel. Pebble mills are used to avoid contamination by metal of the material being ground, to avoid rapid wear due to corrosion, and for other specialized reasons. Belgian silex (silica) blocks formerly were used widely for lining pebble mills, because of their good resistance to wear, light color, and low cost, but the importation of these blocks was suspended early in the war. The stocks of Belgian silex diminished so rapidly that it was found desirable to compare the properties of a number of domestic substitutes for use in critical operations. Accordingly, a study was made to determine the best substitutes for fine grinding of white pigment and for certain heavy-chemical process work such as the disintegration of phosphate rock in weak phosphoric acid solution. A comprehensive survey of substitute lining materials was not contemplated. It was stipulated at the beginning of the investigation that only materials on the market, available in large quantities, would be tested and that these should be reasonable substitutes from a a ance viewpoint as determined from known physical characteristics. Marble and limestone, for example, could be eliminated immediately. Quartzite, granite and porcelain were selected as likely substitutes for Belgian silex and were subjected to quality tests. Materials Tested 1. Belgian Si1ex.—Sample blocks of a standard grade were taken from crates in which they had been imported. The stone was light gray in color and contained inclusions of small clusters of quartz crystals as well as light colored portions that might be calcite. This was a siliceous rock which appeared to be of igneous origin. 2. Quartzite.—Samples of quartzite were obtained from a quarry in Minnesota. The blocks exhibited a crystalline fracture. The stone was pink in color and composed of fine quartz crystals bound together with a siliceous cement. 3. Granite A was a fine-grained granite quarried in South Carolina. 4. Granite B was coarse-grained granite quarried in South Carolina. 5. Granite C was a coarse-grained granite quarried in North Carolina. 6. Porcelain A.—Sample blocks of the pebble-mill lining material were obtained direct from the manufacturer. It was white in color and of lower specific gravity than the natural materials. It did not have a crystalline structure. 7. Porcelain B.—Sample pebble-mill lining blocks of the porcelain were received direct from the manufacturer. It was white

Jan 1, 1948

By C. E. Berry

Natural stone or manufactured porcelain pebbles are used as the grinding elements in pebble mills and the mills are lined with stone or porcelain blocks. Steel balls usually form the grinding medium in ball mills, and the mills may be lined with steel. Pebble mills are used to avoid contamination by metal of the material being ground, to avoid rapid wear due to corrosion, and for other specialized reasons. Belgian silex (silica) blocks formerly were used widely for lining pebble mills, because of their good resistance to wear, light color, and low cost, but the importation of these blocks was suspended early in the war. The stocks of Belgian silex diminished so rapidly that it was found desirable to compare the properties of a number of domestic substitutes for use in critical operations. Accordingly, a study was made to determine the best substitutes for fine grinding of white pigment and for certain heavy-chemical process work such as the disintegration of phosphate rock in weak phosphoric acid solution. A comprehensive survey of substitute lining materials was not contemplated. It was stipulated at the beginning of the investigation that only materials on the market, available in large quantities, would be tested and that these should be reasonable substitutes from a wear-resistance viewpoint as determined from known physical characteristics. Marble and limestone, for example, could be eliminated immediately. Quartzite, granite and porcelain were selected as likely substitutes for Belgian silex and were subjected to quality tests. Materials Tested 1. Belgian Si1ex.—Sample blocks of a standard grade were taken from crates in which they had been imported. The stone was light gray in color and contained inclusions of small clusters of quartz crystals as well as light colored portions that might be calcite. This was a siliceous rock which appeared to be of igneous origin. 2. Quartzite.—Samples of quartzite were obtained from a quarry in Minnesota. The blocks exhibited a crystalline fracture. The stone was pink in color and composed of fine quartz crystals bound together with a siliceous cement. 3. Granite A was a fine-grained granite quarried in South Carolina. 4. Granite B was coarse-grained granite quarried in South Carolina. 5. Granite C was a coarse-grained granite quarried in North Carolina. 6. Porcelain A.—Sample blocks of the pebble-mill lining material were obtained direct from the manufacturer. It was white in color and of lower specific gravity than the natural materials. It did not have a crystalline structure. 7. Porcelain B.—Sample pebble-mill lining blocks of the porcelain were received direct from the manufacturer. It was white

Jan 1, 1947

By C. E. Berry

Natural stone or manufactured porcelain pebbles are used as the grinding elements in pebble mills and the mills are lined with stone or porcelain blocks. Steel balls usually form the grinding medium in ball mills, and the mills may be lined with steel. Pebble mills are used to avoid contamination by metal of the material being ground, to avoid rapid wear due to corrosion, and for other specialized reasons. Belgian silex (silica) blocks formerly were used widely for lining pebble mills, because of their good resistance to wear, light color, and low cost, but the importation of these blocks was suspended early in the war. The stocks of Belgian silex diminished so rapidly that it was found desirable to compare the properties of a number of domestic substitutes for use in critical operations. Accordingly, a study was made to determine the best substitutes for fine grinding of white pigment and for certain heavy-chemical process work such as the disintegration of phosphate rock in weak phosphoric acid solution. A comprehensive survey of substitute lining materials was not contemplated. It was stipulated at the beginning of the investigation that only materials on the market, available in large quantities, would be tested and that these should be reasonable substitutes from a wear-resistance viewpoint as determined from known physical characteristics. Marble and limestone, for example, could be eliminated immediately. Quartzite, granite and porcelain were selected as likely substitutes for Belgian silex and were subjected to quality tests. Materials Tested 1. Belgian Si1ex.—Sample blocks of a standard grade were taken from crates in which they had been imported. The stone was light gray in color and contained inclusions of small clusters of quartz crystals as well as light colored portions that might be calcite. This was a siliceous rock which appeared to be of igneous origin. 2. Quartzite.—Samples of quartzite were obtained from a quarry in Minnesota. The blocks exhibited a crystalline fracture. The stone was pink in color and composed of fine quartz crystals bound together with a siliceous cement. 3. Granite A was a fine-grained granite quarried in South Carolina. 4. Granite B was coarse-grained granite quarried in South Carolina. 5. Granite C was a coarse-grained granite quarried in North Carolina. 6. Porcelain A.—Sample blocks of the pebble-mill lining material were obtained direct from the manufacturer. It was white in color and of lower specific gravity than the natural materials. It did not have a crystalline structure. 7. Porcelain B.—Sample pebble-mill lining blocks of the porcelain were received direct from the manufacturer. It was white

Jan 1, 1947

By Paul Averitt

The U. S. Geological Survey has been actively engaged in work on coal for more than 50 years. During this long period we have released more than 300 publications containing information about coal and coal reserves, including details on the thickness, distribution, and quality of coal, and the structure and stratigraphy of the coal-bearing rocks. We have also cooperated with state surveys on many similar publications. For many areas these reports are the only reliable published data on our resources of coal. During the last several years we have substantially increased our activities above the wartime low. We now have field work in progress, or reports in preparation, on 13 detailed mapping projects distributed as follows: 1. Pennsylvania anthracite field 2. Casselman Basin, Md. 3. Leslie County, Ky. 4. Deep River field, N. C. 5. Coosa field, Ala. 6. Powder River field, Mont. 7. Spotted Horse field, Wyo. 8. Yampa field, Colo. 9. Paonia field, Colo. 10. Trinidad field, Colo. 11. Durango field, Colo. 12. Chaco River area, N. M. 13. Lewis and Thurston County fields, Wash. For two of these areas; the Paonia field, Colo., and the Coosa field, Ala., we have published recently preliminary reports, and final reports are in preparation. In addition, we are nearing completion of a coal reserve study of Montana, and are beginning similar studies in several other states, as part of a program of revising our estimate of national coal resources on the basis of presently available data. Factors Involved in Making Estimates Our responsibilities include detailed field mapping to secure information on areas of outcrop of coal beds, their range in thickness, nature of roof rock, amount of overburden, correlation of the beds, stratigraphy and structure of the coal-bearing rocks, and the preparation of coal reserve figures based on these data. The computation and estimation of resources of coal in the ground, like that of resources of other mineral commodities, involves consideration of many additional purely geological factors that can be appraised best through such regional studies. Regional variations in the thickness and texture of rocks overlying and underlying coal beds, for example, give evidence as to the probable position of the edges of the basin of coal deposition, or may aid in the delineation of sand-filled channels that sometimes cut out coal beds. It is apparent that the detailed field studies, in which data are gathered, are the basis for coal reserve studies, and in our present program these two phases of work are being carried on together. Previous Coal Reserve Estimates For many years we have been aware

Jan 1, 1950