Search Documents

By M. D. Hassialis, A. F. Taggart

ark' observed some years ago that collector-coating reactions with xanthates and with fatty acids clearly follow paths parallel to those prescribed by the familiar mass-action law for reactions in dilute solutions. He proposed, therefore, the logical hypothesis that they are governed by the solubility-product principle. However, he went astray in the application of his proposal to collector coating by overlooking the fact that coating involves a heterogeneous reaction. A mistaken concept of the meaning of the word adsorption also entered. Wark thought that the concentration of metallic ion that must be used in setting up the solubility-product equation for the coating reaction was that which could be obtained by solution of the mineral. Since this is very low for sulphide ores, and since the amount of the collector ion necessary for coating produces an extremely low concentration, the resulting ion-concentration product, under conditions when coating occurs, is much lower than that which would indicate a saturated solution of the collector-coating compound. Hence he was forced to the position that the solubility product governing the coating is much smaller than the standard solubility product. To justify this position it was necessary to postulate a coating mechanism that did not obey the ordinary laws of chemical reaction. This Wark did by adopting the concept that adsorption is a property of matter, rather than merely a more or less ephemeral local concentration thereof. Thus he says (p. 142 of ref. I): "Adsorption is not a purely physical property of the solid surface, for the specific nature of the adsorbed molecule or ion is important." The result was that he destroyed the great potential utility of his postulate by tying it to this erroneous concept in the words (pp. 142, 143): "It will be obvious that the adsorption solubility product is less than the normal solubility product." The writers have found quantitatively in the case of galena and potassium ethyl xanthate, and semiquantitatively in the case of covellite and the same collector, that the coating reaction does follow the mass-action law to the extent that coating occurs when the ordinary solubility product of the coating compound is exceeded, and that coating does not take place under the reverse conditions. In the course of the investigation leading to the establishment of this fact it was necessary to work with xanthate concentrations so low (down to 0.0004 mg. per liter), that very long conditioning times, and bubble-contact times of as much as 16 hr. were necessary sometimes to follow the reactions. The results have led to some illuminating conclusions as to necessary collector concentrations in normal flotation operations, and the action of the frothing agent in connection therewith' The experimental work comprised accurate determination of the standard solubility product of lead ethyl xanthate, development of a much less laborious

Jan 1, 1947

By Alfred R. Powell

LATE in 1944 a group of petroleum and coal technologists was organized in Wash¬ington under the sponsorship of the Petroleum Administration for War and the U. S. Bureau of Mines. This group, known as the Technical Oil Mission, was placed under the authority of the Technical Industrial Intelligence Committee of the Joint Chiefs of Staff, which was then promoting the organization of other missions to be sent to Germany to obtain technical information regarding various industries in that country. The objective of the Technical Oil Mission was to obtain technical data on German production of synthetic oil from coal and all other commercial practices and research projects connected with the oil industry. The primary purpose was to obtain such data as were immediately essential to assist the war against Germany and Japan, with secondary emphasis on technical information that would assist American industry after the end of the war. Since oil-production facilities in Ger¬many and the occupied countries con¬trolled by Germany were the top targets for strategic bombing, the Technical Oil Mission was the first group under the Technical Industrial Intelligence Com¬mittee to enter Germany. A few members of the group flew to London in February 1945 and the majority of the remainder followed in March. In London they were joined by an equal number of British investigators and the combined, mission was then sent into Germany under the authority of the Combined Intelligence Objectives Subcommittee (CIOS). A sum¬mary of the more important information gained by this combined British and American mission is presented below. GERMAN OIL PRODUCTION The oil available to Germany, both natural and synthetic, and including pro¬duction from occupied countries, reached a peak in late 1943 and early 1944. Pro¬duction at this time was at the rate of 1,200,000 metric tons per month, equiva¬lent to i00,000,000 bbl. per year, or about 7 per cent of the wartime production in the United States. Of this production, 50 per cent was crude oil from Romania and Hungary, 12 per cent was crude oil from Germany itself, including Austria, 9 per cent com¬prised coal-carbonization products, that is, tar and light oil, and only the remaining 29 per cent was synthetic liquid fuel made from coal or tar. Synthetic liquid fuel made in Germany was equivalent therefore to less than 2 per cent of war¬time production of crude oil in the United States. The success of the strategic bombing campaign against German oil-production facilities is demonstrated by the fact that by September 1944 the Ploesti fields of Romania and much of the syn¬thetic oil production had been eliminated, so that the amount of oil available to the German war machine was only 25 per cent of the peak quantity mentioned above. By early 1945, when the combined British and American oil mission was entering

Jan 1, 1946

By M. D. Hassialis, A. F. Taggart

ark' observed some years ago that collector-coating reactions with xanthates and with fatty acids clearly follow paths parallel to those prescribed by the familiar mass-action law for reactions in dilute solutions. He proposed, therefore, the logical hypothesis that they are governed by the solubility-product principle. However, he went astray in the application of his proposal to collector coating by overlooking the fact that coating involves a heterogeneous reaction. A mistaken concept of the meaning of the word adsorption also entered. Wark thought that the concentration of metallic ion that must be used in setting up the solubility-product equation for the coating reaction was that which could be obtained by solution of the mineral. Since this is very low for sulphide ores, and since the amount of the collector ion necessary for coating produces an extremely low concentration, the resulting ion-concentration product, under conditions when coating occurs, is much lower than that which would indicate a saturated solution of the collector-coating compound. Hence he was forced to the position that the solubility product governing the coating is much smaller than the standard solubility product. To justify this position it was necessary to postulate a coating mechanism that did not obey the ordinary laws of chemical reaction. This Wark did by adopting the concept that adsorption is a property of matter, rather than merely a more or less ephemeral local concentration thereof. Thus he says (p. 142 of ref. I): "Adsorption is not a purely physical property of the solid surface, for the specific nature of the adsorbed molecule or ion is important." The result was that he destroyed the great potential utility of his postulate by tying it to this erroneous concept in the words (pp. 142, 143): "It will be obvious that the adsorption solubility product is less than the normal solubility product." The writers have found quantitatively in the case of galena and potassium ethyl xanthate, and semiquantitatively in the case of covellite and the same collector, that the coating reaction does follow the mass-action law to the extent that coating occurs when the ordinary solubility product of the coating compound is exceeded, and that coating does not take place under the reverse conditions. In the course of the investigation leading to the establishment of this fact it was necessary to work with xanthate concentrations so low (down to 0.0004 mg. per liter), that very long conditioning times, and bubble-contact times of as much as 16 hr. were necessary sometimes to follow the reactions. The results have led to some illuminating conclusions as to necessary collector concentrations in normal flotation operations, and the action of the frothing agent in connection therewith' The experimental work comprised accurate determination of the standard solubility product of lead ethyl xanthate, development of a much less laborious

Jan 1, 1947

By M. D. Hassialis, Arthur F. Taggart

WARK1 observed some years ago that collector-coating reactions with xanthates and with fatty acids clearly follow paths parallel to those prescribed by the familiar mass-action law for reactions in dilute solutions. He proposed, therefore, the logical hypothesis that they are governed by the solubility=product principle. However, he went astray in the application of his proposal to collector coating by overlooking the fact that coating involves a heterogeneous reaction. A mistaken concept of the meaning of the word adsorption also entered. Wark thought that the concentration of metallic ion that must be used in setting up the solubility-product equation for the coating reaction was that which could be obtained by solution of the mineral. Since this is very low for sulphide ores, and since the amount of the collector ion necessary for coating produces an extremely low concentration, the resulting ion-concentration product, under conditions when coating occurs, is much lower than that which would indicate a saturated solution of the collector-coating compound. Hence he was forced to the position that the solubility product governing the coating is much smaller than the standard solubility product. To justify this position it was necessary to postulate a coating mechanism that did not obey the ordinary laws of chemical reaction. This Wark did by adopting the concept that adsorption is a property of matter, rather than merely a more or less ephemeral local concentration thereof. Thus he says (p. 142 of ref. I): "Adsorption is not a purely physical property of the solid surface, for the specific nature of the adsorbed molecule or ion is important." The result was that he destroyed the great potential utility of his postulate by tying it to this erroneous concept in the words (pp. 142, 143): "It will be obvious that the adsorption solubility product is less than the normal solubility product." The writers have found quantitatively in the case of galena and potassium ethyl xanthate, and semiquantitatively in the case of covellite and the same collector, that the coating reaction does follow the mass-action law to the extent that coating occurs when the ordinary solubility product of the coating compound is exceeded, and that coating does not take place under the reverse conditions. In the course of the investigation leading to the establishment of this fact it was necessary to work with xanthate concentrations so low (down to 0.0004 mg. per liter), that very long conditioning times, and bubble-contact times of as much as 16 hr. were necessary sometimes to follow the reactions. The results have led to some illuminating conclusions as to necessary collector concentrations in normal flotation operations, and the action of the frothing agent in connection therewith. The experimental work comprised. accurate determination of the standard solubility product of lead ethyl xanthate, development of a much less laborious

Jan 1, 1946

By Pierre I. Desré, Donald T. Hawkins, Ralph Hultgren

The torsion effusion method has been used to measure the vapor pressure of thallium over pure thallium in the temperature range 931" to 996'k The resulting 100 cal per g-atom is in excellent agreement with previous values. Vapor pressures of T1 above seven Ag-Tl alloys ranging from 33 to 90 at. pct T1 were measured at 979K. Calculated silver activities show a positive deviation from Raoult's law, approaching ideality near the liquidus. Measured thallium activities scatter less than previous measurements using the electromotive force technique. Values for the silver component were calculated by Gibbs-Duhem integration. This paper reports the results of a study of the liquid Ag-T1 system by the torsion effusion method. The method has been discussed in detail previously1 and will be only briefly summarized here. The sample is contained in a cell which is suspended on a torsion wire. Vapors effusing from orifices on opposite sides of the cell exert a torque on the wire. The torque is related to the vapor pressure by the following relation: where D is the torsion constant of the wire, 4 the angle of torque, fl and f2 the correction factors determined by Freeman and seamy2 to account for orifice length, a1 and a2 the areas of the orifices, and ql and q2 the distances of the orifices from the axis of rotation. By using the same cell for pure thallium and the alloy, it follows that: so that most systematic errors are eliminated in determining the activities. EXPERIMENTAL 99.999+ pct T1 was obtained from the American Smelting and Refining Co. and 99.999 pct Ag was obtained from Cominco American, Inc. Seven Ag-T1 alloys, ranging in composition from x^\ = 0.33 to 0.90, were prepared by melting together weighed amounts of the pure metals in sealed, evacuated Vycor tubes and quenching the melts in water. The apparatus and graphite cells were the same as those used by Hawkins and Hultgren3 in their study of the Pb-Sn system. RESULTS Ten measurements were made on pure thallium in the temperature range 931" to 996K, and the results are presented in Table I. Values of were calculated using tabulated Gibbs (free) energy functions.4 No dependence of on temperature or orifice size was found, indicating that equilibrium was attained. Data for the Ag-T1 alloys are shown in Table 11. Values were smoothed with respect to composition by a plot of where . DISCUSSION The value = 43,520 * 100 cal per g-atom for pure thallium (95 pct uncertainty limit) is in excellent agreement with previous investigations.4 In the Ag-T1 system, this study shows positive deviations from Raoult's law at all compositions. Fig. l gives the phase diagram according to Hansen, and Fig. 2 presents the activity values measured in this study as well as those from electromotive force measurements at 950°K by Terpilowski, Kundys, and slaby.'

Jan 1, 1969

By George A. Morrison

A deposit Of limestone Was known to exist at a depth of 2000 ft under the property of the Columbia Chemical Division of the Pittsburgh Plate Glass Co. at Barber-ton, Ohio. A 662-acre site was selected for the projected mine, some two miles northwest of the plant and near the main line of the Erie Railway. An electric railway 8800 ft in length connects the mine and the plant. The deposit is overlain by 18 ft of un-consolidated (sand and gravel), 100 ft of water-bearing sandstone, and finally 2080 ft of shale into which thin layers of sandstone are embedded. The limestone bed itself is 345 ft thick and overlies 200 ft of gypsum. A 300-ton-per-hour capacity mine was decided upon. Two shafts were deemed advisable, one for production and the second for service; and these were sunk 550 ft apart, one to a depth of 2323 ft and the other to 2258 ft. Each is 16 X , ft in the clear and timbered with 6-in. steel H-sets on 8-ft centers, using 3/8 X 4 X 4-in. angles as studdles. Twelve inch I-beams were used at 160 ft intervals as bearers set in deep hitches and concreted to a vertical depth of 8 ft. Wooden sheathing was first employed but sloughing of the shale created a pressure on this lining and finally concrete was deemed necessary. Water was encountered only within the first 315 ft, flowing at 60 gpm and by grouting this was reduced to 15 gpm. Temporary wooden sinking headframes were installed with 300 cu ft capacity storage pockets and with doors automatically controlled by air cylinders by hoistmen. Each shaft was operated on four 6-hr shifts. The usual V-cut was drilled at the center of the shaft and the round consisted of 34 holes- A 40 pet gelatin dynamite was employed with some 60 pet in the cut holes. Drilling crews consisted of four to six men. Shale drilled easily but became more bed in depth and sandstone wore away the gauge Of the bits rapidly. A room-and-pillar mining system was adopted whereby rooms turned off on 80-ft centers, each room 40-ft wide and 50-ft high. Rib pillars between rooms were cut into 100 ft lengths by frequent holes. Ventilation is achieved through the two shafts, the down-draft through the service shaft, and the return through the pr0duction shaft. The hoist has a a Of 300 tons per hour and is equipped with 10-ton balanced skips requiring. a 2-min cycle Or 30 trips Per hour- Hoisting is designed to Operate by automatic loading and no hoistman is required for normal Operation. The 48 X 60 in. jaw primary crusher is underground. It is fed through chute and chain feeders and is flood-oil lubricated and cooled. An inclined belt conveyor returns oversized material to the crusher. Tramming is by Diesel-powered trucks.

Jan 1, 1948

By F. McIntosh Galbraith

This paper describes the use of the magnetometer, under geological direction, in exploration of the Sudbury nickel district. The writer's experience at Falconbridge has led him to the belief that only through detailed work, and by careful correlation of both geological and geophysical results, can geophysical prospecting methods be applied successfully to mining exploration problems. It is hoped that the basic technique described in the paper will be found to have general application. Introduction Within the past 20 years, geophysical methods of prospecting have become solidly established in the field of petroleum exploration. They have not, however, been similarly adopted by the mining industry, although mining is a far older craft and should be the more advanced in its technique. While, therefore, it is almost a routine matter to have geophysical surveys performed in a new area being tested for oil, a new metal-mining district is usually teeming with prospectors and promoters long before the technical man appears on the scene. Even then, only the more primitive engineering methods are customary in the early stages of exploration. Three factors are chiefly responsible for this situation, The first is the difference between oil pools and ore deposits in their geological modes of occurrence. While most of the known metallic ore bodies have been found outcropping at the surface, petroleum deposits are characteristically buried. This does not mean that all ore deposits outcrop, but neither does it mean that we should rely on "wildcatting" to discover blind ore bodies. The second factor is the relative scale of metallic lodes and accumulations of petroleum. In areal extent, a metal-bearing vein deposit is typically a much smaller geological feature than an oil pool. Presenting a narrower target, it requires closer shooting to score a direct hit. And finally, there is the need, in mining work, for close correlation of the known local geology with geophysical observations. This becomes of increasing importance as the size of the objective diminishes. A geophysical disturbance on a large enough scale will be detected under almost any circumstances and by almost any technique; without benefit of geology, however, the significance of a local anomaly may easily be misread. Campaign at Sudbury In the Sudbury nickel district of Canada, new deposits of nickel and copper have been discovered recently by magnetic methods, under geological supervision. A campaign of exploration, designed to encompass the district eventually, was set in motion in the spring of 1935. After six years, a new and important Ore body has been discovered and its continuity established to 1000 ft. in depth; several areas have been eliminated; and a number of possibilities remain to be tested. This has been accomplished with the expenditure of less than $$I50,000-—including the cost of all diamond drilling. The responsibility for carrying out this campaign was entrusted by the company to its Geological Department, and the under

Jan 1, 1946

By F. McIntosh Galbraith

This paper describes the use of the magnetometer, under geological direction, in exploration of the Sudbury nickel district. The writer's experience at Falconbridge has led him to the belief that only through detailed work, and by careful correlation of both geological and geophysical results, can geophysical prospecting methods be applied successfully to mining exploration problems. It is hoped that the basic technique described in the paper will be found to have general application. Introduction Within the past 20 years, geophysical methods of prospecting have become solidly established in the field of petroleum exploration. They have not, however, been similarly adopted by the mining industry, although mining is a far older craft and should be the more advanced in its technique. While, therefore, it is almost a routine matter to have geophysical surveys performed in a new area being tested for oil, a new metal-mining district is usually teeming with prospectors and promoters long before the technical man appears on the scene. Even then, only the more primitive engineering methods are customary in the early stages of exploration. Three factors are chiefly responsible for this situation, The first is the difference between oil pools and ore deposits in their geological modes of occurrence. While most of the known metallic ore bodies have been found outcropping at the surface, petroleum deposits are characteristically buried. This does not mean that all ore deposits outcrop, but neither does it mean that we should rely on "wildcatting" to discover blind ore bodies. The second factor is the relative scale of metallic lodes and accumulations of petroleum. In areal extent, a metal-bearing vein deposit is typically a much smaller geological feature than an oil pool. Presenting a narrower target, it requires closer shooting to score a direct hit. And finally, there is the need, in mining work, for close correlation of the known local geology with geophysical observations. This becomes of increasing importance as the size of the objective diminishes. A geophysical disturbance on a large enough scale will be detected under almost any circumstances and by almost any technique; without benefit of geology, however, the significance of a local anomaly may easily be misread. Campaign at Sudbury In the Sudbury nickel district of Canada, new deposits of nickel and copper have been discovered recently by magnetic methods, under geological supervision. A campaign of exploration, designed to encompass the district eventually, was set in motion in the spring of 1935. After six years, a new and important Ore body has been discovered and its continuity established to 1000 ft. in depth; several areas have been eliminated; and a number of possibilities remain to be tested. This has been accomplished with the expenditure of less than $$I50,000-—including the cost of all diamond drilling. The responsibility for carrying out this campaign was entrusted by the company to its Geological Department, and the under

Jan 1, 1946

By H. R. Hendricks

THE ore of the Iron King Mine, being very hard and having a very fine crystalline structure, presents many problems in milling that are not present in ordinary lead-zinc ores. This very fine crystallization causes much interlocking of minerals and is most prevalent between the gold and pyrite and the sphalerite and pyrite. The recovery of gold is extremely important in the economic value of the ore and therefore constitutes a large part of the metallurgical problem to be solved. All of the gold is free but it has not been observed in any of the mill products except under very high magnification. Some of the gold is tarnished, and this condition also makes recovery difficult. The gold values have been determined to be highest in association with chalchopyrite and arsenopyrite. The silver occurs mostly in association with galena and tennantite. A small amount of native silver has also been observed occasionally. The galena, being softer than the other minerals, frees much better in grinding. Some oxidation of galena is present in the ore, as the nonsulphide lead content amounts to approximately 10 pct of the total lead. Some oxidation of sphalerite is also present in the ore. Microscopic examination of the zinc concentrate shows many grains in the minus 325-mesh to be half pyrite, together with the fact that some of the zinc is marmatite, makes production of a high-grade zinc concentrate very difficult unless recovery is sacrificed. In the grinding, it has been determined that the flotation feed must be maintained at 85 pct minus 200-mesh to free the minerals sufficiently to make the best economic recoveries. Table I illustrates the effect of fine grinding. It shows that the bulk of the recovered minerals is in the minus 325-mesh size and is the part of the minerals that is more readily freed. The pyrite concentrate is not given in the table because it contains practically no minus 325-mesh. DEVELOPMENT OF PRESENT FLOWSHEET AND MILLING PRACTICE The first milling operation started in 1938, with a mill capacity of 140 tons daily, producing a bulk gold-silver-lead concentrate. After several stages of expansion and changes of the mill flowsheet, the mill is currently treating 380 tons of ore daily and three separate concentrates are produced. In order of their importance and value, these are: (1) lead concentrate, (2) zinc concentrate and (3) pyrite concentrate. The present average grade of mill heads is: gold 0.11 oz, silver 4.00 oz, lead 2.50 pct, zinc 7.60 pct, copper 0.22 pct, iron 22 pet and 30 pct insolubles. Specific gravity of the ore is 3.8. During the period when bulk flotation was practiced, the flowsheet was very simple. The ore was ground fine enough to liberate as much gold, silver and lead as possible. Necessary collectors and frothers were added in sufficient quantity

Jan 1, 1947

By John W. Vanderwilt

The unpredictable behavior of ground movement and subsidence has complicated the problems that attend the extraction of large quantities of ore. Special studies, particularly relating to coal mining, have yielded such a voluminous literature and so many involved controversial theories that a partial review would be difficult. Limited space makes any kind of a review impractical. The features to be considered cover only a relatively small part of the broad problems of ground movement and subsidence, but it is believed that this small part is critical. The practical aspects are important, since they bear directly on safety of mine workings, on recovery of ore and on dilution of ore in block caving and related systems for extracting large quantities of rock. The ground movement to be described occurs outside the vertical boundaries of a caved block in the area that is commonly referred to as being in the "zone of draw." "Draw" is a term that originated in the subsidence problems related to coal mining, and it is defined by a line drawn from the margin of the area caved underground to the most distant fracture at surface on the same side of the caved area as shown in Fig. I.' A line thus drawn is called the cave line, and its angle with respect to the horizontal is the cave angle or angle of draw. It is understood that the line is taken normal to the limit of mining, and in a vertical plane. The prevailing theories as to draw and angle of draw assume that appreciable movement occurred along the cave line, which has been described as a fracture resulting from the shearing action brought about by the weight of the overlying load. Fig. 3 shows diagrammatically the mechanics of ground movement adjacent to an area of subsidence according to the prevailing theory of draw (A, from Royce2) and, for comparison, ground movement observed in the Climax mine (B). The text in Peele's Handbook2 referring to Fig. 2 does not state the meaning of the "original position of top of workable ore" in the rectangular space above "ore in place," and the arrows are not explained. However, this presentation is most concerned with the zones outside the rectangle. According to the prevailing theory, as shown at the extreme left under A, Fig. 2, the vertical tension cracks at surface change at a shallow depth to shear fractures forming the cave line, and it is assumed that appreciable movement takes place along the cave line toward and into the subsiding caved block. The mechanics of ground movement observed in the Climax mine, as shown under B, Fig. 2, does not accord with the prevailing theory, particularly as regards the cave angle and draw. The vertical tension cracks seen at surface die out at depths of 150 to 225 ft. and shear fractures do not develop. Movement is confined at surface to a mantle of rock 50 to roo ft.

Jan 1, 1949

By J. R. Thoenen, M. C. Malamphy, G. K. Dale

The beginning of the war and the events leading up to it precipitated a near crisis in the aluminum industry. Demands for the metal reached proportions far beyond the prewar production capacities and, in addition, the submarine menace seriously curtailed the importation of bauxite from South America, hitherto a chief source of high-grade ore. The situation required an intensive search for domestic ore to augment the reserves and in October 1941 Congress directed the Department of the Interior to investigate the extent, mode of occurrence, and quality of bauxite in the United States. In December of that year the Bureau of Mines and the Geological Survey began the search for bauxite in Arkansas, where more than go per cent of the domestic ore had been produced and where the greatest amount of bauxite was known to occur. The program involves the geophysical and geological investigation of the Arkansas bauxite region and the core drilling of areas considered favorable for the occurrence of bauxite deposits. Cores taken from the bauxite-kaolin zone are sampled and analyzed in the Bureau of Mines laboratory in Little Rock. The information from each of the deposits discovered is then assembled, the bauxite is graded with respect to its possible utility, tonnage estimates are made, and the whole is presented in the form of a war minerals report. Thirty-eight new bauxite deposits had been discovered and investigated at the end of the calendar year 1944, and the presence of several others had been indicated by the drilling. More than 5000 holes had been drilled throughout the bauxite region, and more than 60,000 chemical analyses had been made of samples taken from the bauxite-kaolin zone. A study of the chemical analyses led to certain general conclusions not only with regard to the chemical composition of Arkansas bauxite, but also with regard to its component minerals. Charts and diagrams based on these conclusions have been developed for practical use by the Bureau of Mines: (I) to serve as a check against laboratory analyses, (2) to present tonnage estimates of ore bodies based on mineral composition, (3) to illustrate the relationship of tonnages of bauxite to the alumina, silica, and iron content, and (4) to serve as a control for mining operations by providing a means for quick estimates of the value of the ore from a partial analysis of its chemical constituents. The use of charts and diagrams similar to those discussed in this paper-- is not new. The use of the trilinear diagram for studying the ultimate analyses of coals as of proposed by Ralston in Bureau of Mines Technical Paper 93 (1915) showed that the various ranks of coal fell in different areas on the diagram and that volatile matter, calorific value and other properties could also be plotted by the use of contours. A considerable subsequent literature, largely on classification of coals, has accurnulated since then, showing the utility

Jan 1, 1948

By J. R. Thoenen, M. C. Malamphy, G. K. Dale

The beginning of the war and the events leading up to it precipitated a near crisis in the aluminum industry. Demands for the metal reached proportions far beyond the prewar production capacities and, in addition, the submarine menace seriously curtailed the importation of bauxite from South America, hitherto a chief source of high-grade ore. The situation required an intensive search for domestic ore to augment the reserves and in October 1941 Congress directed the Department of the Interior to investigate the extent, mode of occurrence, and quality of bauxite in the United States. In December of that year the Bureau of Mines and the Geological Survey began the search for bauxite in Arkansas, where more than go per cent of the domestic ore had been produced and where the greatest amount of bauxite was known to occur. The program involves the geophysical and geological investigation of the Arkansas bauxite region and the core drilling of areas considered favorable for the occurrence of bauxite deposits. Cores taken from the bauxite-kaolin zone are sampled and analyzed in the Bureau of Mines laboratory in Little Rock. The information from each of the deposits discovered is then assembled, the bauxite is graded with respect to its possible utility, tonnage estimates are made, and the whole is presented in the form of a war minerals report. Thirty-eight new bauxite deposits had been discovered and investigated at the end of the calendar year 1944, and the presence of several others had been indicated by the drilling. More than 5000 holes had been drilled throughout the bauxite region, and more than 60,000 chemical analyses had been made of samples taken from the bauxite-kaolin zone. A study of the chemical analyses led to certain general conclusions not only with regard to the chemical composition of Arkansas bauxite, but also with regard to its component minerals. Charts and diagrams based on these conclusions have been developed for practical use by the Bureau of Mines: (I) to serve as a check against laboratory analyses, (2) to present tonnage estimates of ore bodies based on mineral composition, (3) to illustrate the relationship of tonnages of bauxite to the alumina, silica, and iron content, and (4) to serve as a control for mining operations by providing a means for quick estimates of the value of the ore from a partial analysis of its chemical constituents. The use of charts and diagrams similar to those discussed in this paper-- is not new. The use of the trilinear diagram for studying the ultimate analyses of coals as of proposed by Ralston in Bureau of Mines Technical Paper 93 (1915) showed that the various ranks of coal fell in different areas on the diagram and that volatile matter, calorific value and other properties could also be plotted by the use of contours. A considerable subsequent literature, largely on classification of coals, has accurnulated since then, showing the utility

Jan 1, 1948

By Rex W. Woods, Morris Muskat

A leastmsquare analysis procedure has been developed and applied for the study of the deviations in estimations of oil in place as given by the material-balance equations. The data used were those obtained from field observations on the Jones sand in the Schuler pool, Arkansas, and the Monroe dolomite in the Reed City pool, Michigan. Possible effects of water intrusion were taken into account by expressing the cumulative water influx in terms of various functions previously proposed in the literature. Formulas were developed and values calculated for the minimum deviations and minimal percentage deviations in the calculated volumes of oil in place from the average values, as could be obtained by suitable choice of the water encroachment and initial gas-cap volume parameters. The results show that the fluctuations in these calculated volumes are very insensitive to the values chosen for the rate of water intrusion and initial gas-cap volume, and hence cannot be safely used in discriminating between spurious values for these parameters and such as actually pertain to the producing reservoirs. Moreover, the exact form of the water-intrusion function seems to have but little effect on the fluctuations in the computed oil in place. Accordingly, it is concluded that the material-balance method does not of itself provide a satisfactory criterion for determining the basic physical unknowns of producing reservoirs or in making conclusive decisions regarding the production mechanism, unless independently established geological control data are available for eliminating unreasonable values for the reservoir parameters, even though they may still satisfy the material-balance formulas. If, however, from core or logging data the initial oil in place and the gas-cap volume can be established in advance, the material-balance formulas can be inverted to find the water intrusion. Moreover, by determining by such calculations the water-intrusion coefficient, the iuture production performance can then be predicted by the aid of the materiaI-balance formulas for specified operating conditions. This type of application may be of particular value in predicting the results of Pressure-maintenance operations. Introduction The evaluation of the forces acting upon an oil reservoir is a problem of considerable interest to the operator as an aid in determining the proper method of operation for the reservoir to obtain an optimum recovery of oil. In many pools, the nature and magnitude of the forces acting upon the reservoir remain unknown until an appreciable amount of ultimate recovery is obtained. To be of value to the operator, a reliable interpretation of reservoir performance should be available in the early life of the pool to permit an optimum plan of operation. Progress has been made in an understanding of reservoir behavior and the importance of the different factors involved. The material-balance method of estimating oil in place has been proposed as a tool in analyzing reservoir-performance problems.l The solution of such problems by this method ordinarily involves two or more unknown values relating to the nature of the reservoir, and the results

Jan 1, 1945

By S. D. Thompson

An AIME transaction by P.L. Allsman (1960), "Analysis of Explosive Action in Breaking Rock," contains many useful concepts applicable to blast design. Of special interest was the derivation of a heave blasting burden formula, which is important in establishing the maximum burden. Unfortunately, its derivation contains a fundamental error and then a compensating one. This formula was: [bImpulse _P d At max =nwuwu where: bmax = maximum burden in m (ft). P= average detonation pressure in N/m2 (lb per ft2). A= duration of the average detonation pressure in sec. n= 3.1416. w= specific weight of rock in N/m3 (lb per ft3). u= minimum velocity that must be imparted to the rock in m/sec (ft per sec). d= borehole diameter in m (ft).] The derivation used the impulse-momentum principle, with a 0.3 m thick (1 ft thick) radius of rock mass being acted on by an explosive impulse. However, the rock weight was not converted to mass by dividing by the gravitational constant. This mistake can be verified by checking the units in the formula, which resolve into m1/2-sec instead of meters. Adding the gravitational constant corrects this: [P d Atbmax =gu g = gravitational constant equal to 9.81 m/sect (32.2 ft per sec2).] If the minimum velocity is now taken as 0.3 m/sec (1 ft per sec), as was recommended, excessively large burdens result. Any appropriate rock velocity should be capable of throwing the rock mass a minimum distance so that the swell needed for breakage can occur. Unless the burden is extremely small and the bench height is very high, it is unlikely that a velocity of only 0.3 m/sec (1 ft per sec) will be sufficient. A review of the literature indicates that average rock velocities observed by camera studies typically range from 15 to 30 m/sec (50 to 100 ft per sec) (duPont deNemours and Co., 1977; Tansey, 1979). On this basis, a minimum rock velocity of about 15 m/sec (49 ft per sec) would be expected and not 0.3 m/sec (1 ft per see). When a velocity of 15 m/sec (49 ft per sec) is inserted into the corrected formula, the results approximate those of the original formula with a velocity of 0.3 m/sec (1 ft per sec). The errors were approximately self-compensating [(9 = 1.24)]. ? References Allsman, P.L., 1960, "Analysis of Explosive Action in Breaking Rock," Transactions, AIME, Vol. 217, pp. 475-476. E. I. duPont deNemours and Co., 1977, Blasters' Handbook, 175th Anniversary Edition, Dupont, Wilmington, DE, pp. 233. Tansey, D.O., 1979, "The DuPont Sequential Blasting System," CIM Bulletin, Vol. 72, July, p. 80. Thompson, S.D., 1981, "Critical Review and Revision of Surface Blasting Practice," MS thesis, West Virginia University, pp. 308-316.

Jan 1, 1986

By A. R. Denison

Several productive areas in the Mid-Con-tinent are broadly and briefly examined with respect to the present depth of drilling on productive structures, and the thickness of sediments remaining untested. Evidence is offered to show that a vertical mile to two miles of untested but prospective formation remain within reach of the drill. In no case would a well deeper than 15,000 ft. be required, and in most cases to no greater depth than 10,000 ft. Recent outstanding success of deeper prospecting in West Texas demonstrates the merits of deeper drilling on known structure. Introduction New fields discoverd during I942 equaled or exceeded the number in any preceding year. The total amount of oil found by these discoveries was less than in any previous year, for which accurate records are available. This means that the pools now being discovered are much smaller than in past years. This is to be expected, since the prospects available during 1942 were largely those overlooked in the earlier years and therefore represent a second or third order (in quality) of structural feature. This failure to find pools of good size and quality raises grave doubt as to the security of our future oil supply. With military needs rising almost daily, and the period of heaviest con- sumption in our war effort still in the future, there is even a growing doubt as to our ability to supply the amount needed for our ultimate victory. This does not mean that our reserves are inadequate, but rather that our "capacity to produce" may be inadequate. Lacking large fields with flush production, our capacity to produce is rapidly approaching our current needs. ,Since the industry is unable to find the large new fields necessary to keep a safe margin of "capacity to produce," other means are needed. It seems obvious that one of these should be deeper prospecting on the large, proven, productive structural features now known. The exploratory wildcat is drilled primarily in search of a trap and the reason for failure to find oil and gas in nine out of ten cases is due to the absence of a suitable trap under the drill site. Therefore, deeper drilling on a known structural feature that is productive largely eliminates the greatest hazard in wildcat drilling. While by no means all the oil known today is found in structural traps—in fact, some have estimated that less than half is so located— the fact remains that structural traps are far more commonly the oil fields that have multiple horizons of production superimposed one over the other. Outstanding examples are the Eldorado field in Kansas, the Tonkawa and Cushing fields in Oklahoma, the Louden and Salem pools of Illinois, and the richest and most prolific of all structural traps, the Long Beach, Ven-tura and other similar fields of California.

Jan 1, 1944

By L. P. Davidson

ThE new electrolytic zinc plant of the American Zinc Company of Illinois commenced operation in April 1941. The simple flowsheet using the standard current density and the economic reasons that dictated it are given herewith. The Evans-Wallower Zinc Co. built an electrolytic zinc plant at Monsanto, Ill., in 1929 and operated it for about two years. The plant stood idle from 1932 and was purchased by the American Zinc Co. in 1940. Because of the condition of the equipment, excepting the motor generator set, a complete rebuilding was necessary. The Fairmont City plant of the American Zinc Co. could treat the leach residues, the purification cake and the skimmings from the melting furnace in its various plants. This possibility permitted a simple flowsheet with good economic results. The flowsheet is shown in Fig. I. The calcined concentrates are leached in mechanically agitated tanks with spent electrolyte and such ferric iron solution as necessary. When the acid has been neutralized and the iron coagulated, the fluid is discharged to settling tanks. The underflow from these thickeners is filtered on a Moore filter; the filter cake leaves the plant for retreatment and the filtrate joins the thickener overflow. Zinc dust is added to this solution until the copper and cadmium are precipitated. The pulp is filtered through Shriver presses, which deliver the purified solution to stor- age tanks, and the copper-cadmium-zinc cake is shipped for retreatment and recovery of these three metals. The purified solution is electrolyzed; the regenerated acid is returned for use in the leaching plant and the cathode zinc, after stripping, goes to the melting furnace, from which it is cast in slabs. The skimmings from the melting furnace are shipped to the Fairmont City plant for reduction to metal in the retort furnaces. The choice of this simple flowsheet was made possible only because of the facilities of the Fairmont City plant. The long leaching pried, with high acid content and high temperature which characterize the high-density process, gives a higher zinc extraction but also dissolves more impurities, which must be removed. The same is true to a lesser degree of the multi-step leaching of the western low-density plants. By the sacrifice of some initial extraction, solutions can be obtained that are relatively easy to purify and give good ampere efficiency. This loss in initial extraction is made up in the retreatment of the residues in the Waelz plant. The impurities that accompany the zinc thus extracted are inconsequential when the Waelz product is treated in a distillation plant. It was recognized that this flowsheet would require a somewhat greater amount of sulphuric acid—-eithcr as acid or as sulphate sulphur in the calcine—because of poorer washing. The sulphuric acid plant at Fairmont City could deliver 60" Bè. acid to compensate for the sulphate loss and the cost would be less than the cost of more intensive washing.

Jan 1, 1943

By A. R. Denison

Several productive areas in the Mid-Con-tinent are broadly and briefly examined with respect to the present depth of drilling on productive structures, and the thickness of sediments remaining untested. Evidence is offered to show that a vertical mile to two miles of untested but prospective formation remain within reach of the drill. In no case would a well deeper than 15,000 ft. be required, and in most cases to no greater depth than 10,000 ft. Recent outstanding success of deeper prospecting in West Texas demonstrates the merits of deeper drilling on known structure. Introduction New fields discoverd during I942 equaled or exceeded the number in any preceding year. The total amount of oil found by these discoveries was less than in any previous year, for which accurate records are available. This means that the pools now being discovered are much smaller than in past years. This is to be expected, since the prospects available during 1942 were largely those overlooked in the earlier years and therefore represent a second or third order (in quality) of structural feature. This failure to find pools of good size and quality raises grave doubt as to the security of our future oil supply. With military needs rising almost daily, and the period of heaviest con- sumption in our war effort still in the future, there is even a growing doubt as to our ability to supply the amount needed for our ultimate victory. This does not mean that our reserves are inadequate, but rather that our "capacity to produce" may be inadequate. Lacking large fields with flush production, our capacity to produce is rapidly approaching our current needs. ,Since the industry is unable to find the large new fields necessary to keep a safe margin of "capacity to produce," other means are needed. It seems obvious that one of these should be deeper prospecting on the large, proven, productive structural features now known. The exploratory wildcat is drilled primarily in search of a trap and the reason for failure to find oil and gas in nine out of ten cases is due to the absence of a suitable trap under the drill site. Therefore, deeper drilling on a known structural feature that is productive largely eliminates the greatest hazard in wildcat drilling. While by no means all the oil known today is found in structural traps—in fact, some have estimated that less than half is so located— the fact remains that structural traps are far more commonly the oil fields that have multiple horizons of production superimposed one over the other. Outstanding examples are the Eldorado field in Kansas, the Tonkawa and Cushing fields in Oklahoma, the Louden and Salem pools of Illinois, and the richest and most prolific of all structural traps, the Long Beach, Ven-tura and other similar fields of California.

Jan 1, 1944

By Stanley D. Michaelson

The selection of the proper size of grinding mill for a given installation has long been a subject of discussion by mill manufacturers, consulting engineers, and their clients. It would be presumptuous for the author to propose a simple cure-all. Instead this paper describes a method that has been used over a period of years to determine mill size with a reasonable degree of accuracy. Furthermore, this method claims no theoretical background, for ball milling, as practiced today, is still an art. The selection of the proper size and type of mill must, therefore, be made on an empirical basis. A ball mill, in order to grind, must deliver power through its grinding media to the material to be ground. Assuming that a mill is properly supplied with grinding media, ore pulp, and power, the amount of grinding done is closely proportional to the power expended. With this as a basic premise we can, for the moment, forget about type of mill (i.e., overflow, low-level mill, or other design) and base our calculation of mill size on the total power required to grind a ton of a particular ore from a given size of feed to a given size of product. When this is determined the type and size of mill, its speed, and the weight of the load of grinding media can be selected to absorb this amount of power. Development of Technique Some years ago, W. L. Maxson, F. Cadena, and F. C. Bond, working in the Minerals Research Laboratory of Allis-Chalmers Co., Milwaukee, developed and described a laboratory technique for comparing grindability (or relative ease of grinding) of various ores at different mesh sizes of grind.' Additional papers2 have described the work done since that time, and the most recent paper3 summarizes results for hundreds of tests on many ores and materials. The essentials of the testing method are: a 12 by 12-in. laboratory mill operating at a constant speed of rotation, using a constant volume of ore, and a constant ball load having a relatively constant grinding surface. Tests are run at 250 per cent circulating load with the feed, circulating load and products screened on calibrated Tyler standard screens. Certain ores from operating mills, representing various mineralogical types, were selected for reference and designated "standard ores." In most cases, detailed studies of the grinding circuits were made when samples of mill feed were taken for grindability tests. Each analysis formed a basis for comparison of the grindability in the laboratory with actual power requirements for a particular grinding circuit. In addition, a critical study was made to evaluate the differences in the various grinding circuits so that two or more field installations having different layouts (single-stage grinding, two-stage grinding, or others), and using mills of various diameters operating at various speeds with differing circulating loads, etc., could be compared. Large-scale tests by mill operators complemented by laboratory investiga-

Jan 1, 1947

By L. P. Davidson

ThE new electrolytic zinc plant of the American Zinc Company of Illinois commenced operation in April 1941. The simple flowsheet using the standard current density and the economic reasons that dictated it are given herewith. The Evans-Wallower Zinc Co. built an electrolytic zinc plant at Monsanto, Ill., in 1929 and operated it for about two years. The plant stood idle from 1932 and was purchased by the American Zinc Co. in 1940. Because of the condition of the equipment, excepting the motor generator set, a complete rebuilding was necessary. The Fairmont City plant of the American Zinc Co. could treat the leach residues, the purification cake and the skimmings from the melting furnace in its various plants. This possibility permitted a simple flowsheet with good economic results. The flowsheet is shown in Fig. I. The calcined concentrates are leached in mechanically agitated tanks with spent electrolyte and such ferric iron solution as necessary. When the acid has been neutralized and the iron coagulated, the fluid is discharged to settling tanks. The underflow from these thickeners is filtered on a Moore filter; the filter cake leaves the plant for retreatment and the filtrate joins the thickener overflow. Zinc dust is added to this solution until the copper and cadmium are precipitated. The pulp is filtered through Shriver presses, which deliver the purified solution to stor- age tanks, and the copper-cadmium-zinc cake is shipped for retreatment and recovery of these three metals. The purified solution is electrolyzed; the regenerated acid is returned for use in the leaching plant and the cathode zinc, after stripping, goes to the melting furnace, from which it is cast in slabs. The skimmings from the melting furnace are shipped to the Fairmont City plant for reduction to metal in the retort furnaces. The choice of this simple flowsheet was made possible only because of the facilities of the Fairmont City plant. The long leaching pried, with high acid content and high temperature which characterize the high-density process, gives a higher zinc extraction but also dissolves more impurities, which must be removed. The same is true to a lesser degree of the multi-step leaching of the western low-density plants. By the sacrifice of some initial extraction, solutions can be obtained that are relatively easy to purify and give good ampere efficiency. This loss in initial extraction is made up in the retreatment of the residues in the Waelz plant. The impurities that accompany the zinc thus extracted are inconsequential when the Waelz product is treated in a distillation plant. It was recognized that this flowsheet would require a somewhat greater amount of sulphuric acid—-eithcr as acid or as sulphate sulphur in the calcine—because of poorer washing. The sulphuric acid plant at Fairmont City could deliver 60" Bè. acid to compensate for the sulphate loss and the cost would be less than the cost of more intensive washing.

Jan 1, 1943

By Stanley D. Michaelson

The selection of the proper size of grinding mill for a given installation has long been a subject of discussion by mill manufacturers, consulting engineers, and their clients. It would be presumptuous for the author to propose a simple cure-all. Instead this paper describes a method that has been used over a period of years to determine mill size with a reasonable degree of accuracy. Furthermore, this method claims no theoretical background, for ball milling, as practiced today, is still an art. The selection of the proper size and type of mill must, therefore, be made on an empirical basis. A ball mill, in order to grind, must deliver power through its grinding media to the material to be ground. Assuming that a mill is properly supplied with grinding media, ore pulp, and power, the amount of grinding done is closely proportional to the power expended. With this as a basic premise we can, for the moment, forget about type of mill (i.e., overflow, low-level mill, or other design) and base our calculation of mill size on the total power required to grind a ton of a particular ore from a given size of feed to a given size of product. When this is determined the type and size of mill, its speed, and the weight of the load of grinding media can be selected to absorb this amount of power. Development of Technique Some years ago, W. L. Maxson, F. Cadena, and F. C. Bond, working in the Minerals Research Laboratory of Allis-Chalmers Co., Milwaukee, developed and described a laboratory technique for comparing grindability (or relative ease of grinding) of various ores at different mesh sizes of grind.' Additional papers2 have described the work done since that time, and the most recent paper3 summarizes results for hundreds of tests on many ores and materials. The essentials of the testing method are: a 12 by 12-in. laboratory mill operating at a constant speed of rotation, using a constant volume of ore, and a constant ball load having a relatively constant grinding surface. Tests are run at 250 per cent circulating load with the feed, circulating load and products screened on calibrated Tyler standard screens. Certain ores from operating mills, representing various mineralogical types, were selected for reference and designated "standard ores." In most cases, detailed studies of the grinding circuits were made when samples of mill feed were taken for grindability tests. Each analysis formed a basis for comparison of the grindability in the laboratory with actual power requirements for a particular grinding circuit. In addition, a critical study was made to evaluate the differences in the various grinding circuits so that two or more field installations having different layouts (single-stage grinding, two-stage grinding, or others), and using mills of various diameters operating at various speeds with differing circulating loads, etc., could be compared. Large-scale tests by mill operators complemented by laboratory investiga-

Jan 1, 1947