Search Documents

By J. Suiter, H. F. Ryan

H. F. Ryan and J. Suiter (CSIRO)—In this paper the authors have presented "a physical model which has as its central hypothesis the solution strengthening of regions along grain boundaries in the order of tens of angstroms thick", and their calculations have used 40Å as the zhalf-width of this boundary region. Selection of this value by the authors suggests that they were unaware of a number of recent field-ion microscope observations of grain boundary structures (e.g., Refs. 29 and 30). The accompanying figure, Fig. 9, shows a portion of an ion micrograph of a tungsten specimen containing a grain boundary, and the regular arrangement of atoms in various crystal planes in each grain can be seen, except in the boundary zone which is not more than two atom diameters in width. Since it is expected that solute atoms will segregate only to the region where the lattice is disturbed, it would seem that a value of 4Å for the half-width of the boundary region would be more appropriate than the value of 40Å assumed by the authors. If the former value is used in Eq. [8] of their paper to obtain curves showing solute concentration in the grain boundary as a function of temperature, the resulting curves differ significantly from those obtained by the authors. Although there are only relatively slight changes in the regions corresponding to higher temperatures (i.e., grain boundary concentrations of approximately 1 at. pet), at lower temperatures the curves are no longer realistic. For example, the curve corresponding to u = 7000 cal per mole gives a solute grain boundary concentration in excess of 100 pet at a temperature of approximately 360°K, and "flattens out" at a grain boundary concentration of about 300 pet! Similar results are obtained with each of the other curves. Ion microscopy of dilute solid-solution alloys has shown that solute atoms give rise to image points which in most cases are of higher intensity than those of the solvent atoms.31 If the same behavior occurs when the solute atoms are present in much lower concentrations then ion microscopy should provide a sensitive tool for studying the segregation of impurities to the grain boundary regions. Although many grain boundaries in tungsten have been examined after different thermal and mechanical treatments, there has not been, as yet, any systematic study of such segregation. In general the micrographs show no clear indications of marked grain boundary segregation, but occasionally areas are found where the grain boundary contains an appreciable number of image points of high intensity in a very narrow zone, see Fig. 9. If it is assumed that these correspond to impurity atoms then it is possible to estimate the impurity concentration both in the grain boundary and within the body of the grains. Application of this method (to a larger area

Jan 1, 1965

By J. H. Frye, J. W. Caum

One of the most important methods of increasing the hardness of metals is alloying. In spite of the widespread use of alloys, the fundamental mechanism of alloy hardening is little understood. This is true even of the simplest form of alloy, the primary substitutional solid solution in which solute atoms substitute for solvent atoms at random in the crystal lattice of the latter. A fundamental understanding of the mechanism of solid-solution hardening would be important, both because of the widespread use of alloys of this type and because of the light that might be thrown on the mechanism of hardening in more complicated alloys. The present investigation covers the hardness of primary substitutional solid solutions of zinc, gallium, germanium, and arsenic in copper. All of these are B subgroup elements from the third period of the periodic table. Cu, Zn, Ga, Ge, and As are in groups I, 11, 111, IV, and V, respectively, and lie just to the right of the transition elements. Because of their cost, it is unlikely that Ga-Cu and Ge-Cu solutions will ever be of commercial importance, but the intent of this study has been to discover some of the fundamentals of solid-sdstion hardening and it has been demonstrated that such a study is far more likely to be fruitful if alloys are made up on the basis of position of the constituent elements in the periodic table than if commercially important alloys are used. Many investigations have been made of the hardness of substitutional solid solutions, but lack of attention to purity of the metals, infrequent grain-size control, and the use of varying testing techniques have virtually invalidated any comparisons. The purpose of most investigations has been to solve immediate problems and not to solve the primary problem: Why do solid solutions usually have a greater hardness than pure metals? Previous Work Theories have been advanced to account for the hardness of solid solutions, but relatively little experimental work has been done. Perhaps the first experimental work of merit was that of Norbury1 on copper alloys. He showed that for several alloys there was a correspondence between the hardness of one atomic per cent solutions and atomic volume of the solutions. More recently Brick, Martin, and Anger2 have investigated the effect of various solute elements on the hardness of copper. They concluded that the hardening effect of these solutes depended "primarily on the difference in atomic volume of solute and solvent or, relatedly, upon the parameter change of the solvent or the extent of solid solubility." They also observed the effect of these elements on hardness and texture developed by rolling and by annealing of rolled material. Austin3 examined the hardness and response to heat-treatment of various iron solid solutions. Frye and Hume-Rothery4 measured the hardness of a number of silver solid solutions containing approximately 1 References are at the end of the paper.

Jan 1, 1943

By Charles W. Goodale

In the course of the preparation of my paper on " The Occurrence and Treatment of the Argentiferous Manganese Ores of Tombstone District, Arizona" (Dam., xvii., 767), my attention was called to two patents which have been issued for the use of a diaphragm at the upper end of a Howell furnace, whose importance merits more than a passing reference. Mr. J. K. Pardee invented and first put into use in the Algon quin mill, at Philipsburg, Mon., in 1880, a ('new' and useful im provement in rotary ore-roasting furnaces," which was intended "to increase the capacity, effectiveness and working economies of such furnaces." The following description and accompanying figures are taken from the patent papers, dated December 21st, 1880: Fig. 1 is a side elevation of the feed-end of the Howell rotary furnace, with parts broken away, the better to exhibit my invention. Fig. 2 is an end elevation of the same. Fig. 3 is an end elevation of the same, showing a modification of my invention. In operating a furnace of this kind, of the capacity of one ton of ore an hour, it was found that for the best work the two fire-places (one at each end of the revolv ing cylinder) consumed about ten cords of wood every twenty-four hours, and that about twenty-fonr tons of silver-ore were introduced through the feed-pipe. It was also found that of the amount of ore, fully one-third did not go through the revolv ing cylinder, but went into the dust-chanibers about the feed-end of the furnace or cylinder, and this ore going into the dust-chambers was found not to be sufficiently chloridized for amalgamation, but had to be re-roasted. I then caused to be made, out of boiler-plate iron, a segment of a circle, the height of which was about one third of the diameter of. the cylinder or furnace, the circumference of the circle being smaller than the circumference of the furnace, so that about a half-inch space would be left between the plate and the furnace, when said plate or segment was in position. This segment or plate of iron was then fastened to the bottom of the feed pipe, as shown in the drawings, wherein A represents the revolving cylinder or furnace; B, the fire-place and dust-chambers at the feed-end of said furnace; C, the inclined feed-pipe, and D, the diaphragm, partition, or plate fixed within said furnace, A. With the diaphragm or plate, D, in the position shown, the furnace was run for about a month, and it was found that with the furnace in best working condition only four cords of wood every twenty-four hours were consumed, that no fire was required at the feed-end of the furnace, that not one-twelfth of the ore

Jan 1, 1890

By P. A. Beck

ACCORDING to the traditional definition,1 re-x crystallization is a process taking place upon annealing of cold worked metals, characterized by the appearance of new strain-free grains, growing at the expense of the cold worked grains until ultimately the new crystals completely replace the cold worked structure. In metals like brass this process was observed long ago to take place simultaneously with the return of the mechanical properties to those characteristic of well annealed material. The above definition implicitly assumes that the matrix in which the new grains are growing is essentially still in the cold worked condition at the time it is absorbed by the new grains, i.e., that the energy stored in the metal during cold working is not greatly decreased by recovery, prior to recrystallization. Accordingly, the bulk of this energy is assumed to serve as the driving force for the process of recrystallization. Recently, a great deal of evidence accumulated, indicating that the traditional concept may be considerably in error. Suzuki' found that by far the largest portion of the stored energy of cold work in compressed polycrystalline copper is released in the early stages of annealing, well in advance of recrystallization. Thus, the new recrystallized grains are undoubtedly growing in a matrix which is, at least energetically, no longer in the cold worked condition, but has nearly returned to the annealed state. It is true that in Suzuki's experiments the major hardness changes due to annealing were observed to take place concurrently with the formation and growth of the new grains, but this process apparently involved the release of only a minor residual fraction of the stored energy of cold work. Confirming in this respect the views of Wood," several recent investigations by various techniques lead to the conclusion that the grains of many, if not all, metals in the cold worked condition consist of small, slightly disoriented "crystallites" or "sub-grains".* (After appreciable deformation at room temperature, the subgrain size in copper appears to be about 7.104 cm and in high purity aluminum about 2.10-4 cm.) Recent investigations which demonstrated this phenomenon most convincingly are those of Heidenreich8 with hammered high purity aluminum, of P. B. Hirsch and collaborators7,8 with cold worked polycrystalline aluminum, copper, nickel, iron, gold, etc., and of Warren and Averbach9 with a rolled copper plus 2 pct Si single crystal. In addition to the existence of slightly disoriented sub-grains, the cumulative evidence from these investigations also shows that in the cold worked condition the subgrains themselves are severely strained. With regard to the early stages of annealing, Heiden-reich's results indicate that within the subarains of hammered high purity aluminum the strain gradually disappears, without discernible migration of the subboundaries. This recovery process presumably accounts for the major portion of the energy release

Jan 1, 1953

By Sherman L. Pease

An inexpensive and relatively rapid method that can be used by field crews is described. Fluid movement is determined by releasing a tracer (dye) in the well at a predetermined level and, after an interval of time, sampling the well fluid at another level. The testing equipment consists of a combined crusher and sampler unit that is run into the well on a wire line. The rate of movement can be calculated from time-volume relationships. Description of Method It is often desirable to determine whether there is occurring any transfer of fluid from point to point in a shut-in well, and, if so, to measure the rate of movement. When it is desired to examine a large number of wells for possible "thief" sands, the time and expense will be considerable unless the method used is inexpensive and rapid. After experimentation with several possible solutions to the problem, the Production Department of the Shell Oil Co., Inc., developed the apparatus described herein, which has proved satisfactory. Routine operations with it can be carried out by field production crews with a minimum of technical supervision and with negligible investment in equipment. The method is based upon releasing a suitable tracer in the well fluid at a known level, and recovering a sample of well fluid at another level after a measured interval of time. Repetition of this process with different time intervals between release and sampling gives the necessary data. For purposes of illustration, the setup for measuring migration of fluid in an upward direction is described in the following paragraphs. The arrangement of equipment is shown diagrammatically on Fig. I. The elements of the combination unit are the tailpiece, the crushing device, the spacer and the sampling device. The lengths of the tailpiece and spacer are varied to place the crushing and sampling devices in the desired positions in relation to the sands being tested. The crushing device breaks the glass bottle containing the tracer when the tailpiece strikes the bottom of the well and the tension on the sand line is slackened. Because of the open construction of the crushing device, the tracer is quickly and completely disseminated in the well fluid. The sampling device is a suction bailer, which obtains a sample of the fluid surrounding the perforated nipple just before the unit is picked up off bottom. The sample is retained in the barrel by the ball valve for examination at the surface. Normally, on the first run into a well, the sample is obtained near the releasing point of the tracer, and thereafter samples are taken near the base of the upper sand if migration is indicated by the dilution or absence of the tracer in the initial sample. The length of the time interval between the releasing of the tracer and the sampling of the well fluid is varied for successive runs, attempting first to establish the rate within limits and then to define it more accurately by additional runs if necessary.

Jan 1, 1946

By Avnulf Muan, Egil Aukrust

Activity-composition curves jor cobalt oxide and manganese oxide in solid solutions with spinel-type structure have been determined by studying the equilibrium between the spinel phase and a coexisting solid-solution phase in the tewzperature range 1100" to 1400"C. Within limits of experimental error, the system displays the behavior of a regular solution. The excess integral free energy of mixing is represented by the equation . The standard free energy of formation of cobalt manganite, CoMn,O,, from the oxide components COO mzd Mn2OS at 1200°C is calculated to be -8.6 kcal. AMONG the technologically and theoretically most important oxide phases are those which crystallize with the same structure type as the mineral MgO . A120,. Although the name spinel originally was used only for this mineral, the term is generally used today to designate the whole group of oxide phases with this same structure type. It is in this wider meaning that the term is being used in the present paper. The previous literature on spinels is very extensive. There are two aspects of spinels which have attracted particular attention: the structure, including the nature and distribution of the cations present, and the physical properties (electric, magnetic). The status of knowledge in these fields has been well-summarized in recent review articles.1'2 By contrast, thermodynamic properties of spinels are virtually unknown. Delineation of the activity-composition curve over the whole composition range of a solid-solution series with spinel-type structure is the objective of the present work. The system at elevated temperatures (>1000"C) constitutes such a series. The activity-composition curves for this system can be calculated from a study of the equilibrium between the above spinel solid solution and a solid solution (Co,Mn)O with sodium chloride-type structure. Data for the latter solid solution have become available recently.3 The system, in contact with metallic CO at 1200°C, obeys Raoult's law. The determination of the activity-composition curve for the spinel phase is based on the following relations. Consider the reduction-oxidation equilibrium for cobalt ions according to the equation: Because it is impossible in practice to measure single activities of electrically charged constituents, we will treat the equilibria in terms of electrically neutral components. Eq. [I] can then formally be written as follows: where and the activities of cobalt oxide in the (Co,Mn)O and the spinel solid-solution phases, respectively, K is a constant at constant temperature, and Pa is the oxygen pressure of the gas phase. The numerical value of K can be determined from a determination of the oxygen pressure P& for the equilibrium coexistence of Cos04 and COO in the binary system Co-0. Under these circumstances be set equal to 1, and hence K = [Po Eq. [3] can therefore be written

Jan 1, 1964

By P. H. Cardwell

The effect of various plastics upon the permeability of a sand and the mechanism of their ensuring permeability within the consolidated sand body is discussed. Data are presented on various properties of the plastic materials used in sand consolidation and the effect of temperature and usable temperature ranges are considered. The recovery of petroleum from uncon-solidated sands presents serious production problems, owing to sloughing of the formation. The solution of some of these problems usually has been by mechanical methods.' The ideal way of controlling the sloughing tendencies of these un consolidated formations, however, is to prevent the movement of the individual sand grains by the use of a bonding medium. A step in the desired direction was taken by Irons and Stcesser2 when they taught the use of liquid plastics to produce a consolidating deposit that prevents sloughing. More recently, Wrightsman and Buckley3 proposed a modification of this process. In this use of the liquid plastic, the sand grains become coated and the ensuing hardening of the plastic by polymerization or condensation cements together the sand Particles. Liquid plastics that have been suggested for this Purpose are of the following types: phenolformaldehyde, alkyd resins, vinyl type resins, polystyrene and the acrylic esters. When the flow of fluids through a sand must not be materially reduced, it is essential only to cement together the sand grains with liquid plastic and leave a portion of the interstitial space for fluid flow. TO be assured of obtaining fluid flow through the sand interstices after injection of plastic, it has been necessary in the past to remove the excess plastic from the interstices between the particles before it sets. Wrightsman and Buckley suggest two methods for the removal of the excess plastic from the interstices of the sand: (I) to flush the excess plastic back into the formation, away from the well bore, by use of oil or water; (2) to produce the well before the plastic has set, thereby moving the excess plastic into the well bore. Under certain well conditions it is very difficult to remove the excess plastic from all parts of the formation by either of these methods and leave the formation consolidated with no sections completely sealed. The method* described herein of retaining permeability within a sand body is to use a liquid plastic that upon setting ensures permeability within the consolidated sand body. This cements the sand grains but obviates the need for removing plastic from the interstices of the sand. One of the ways of accomplishing this is to use a liquid plastic that occupies a considerably greater volume than the solidified resin it yields on further polymerization or condensation in situ. In order to be satisfactory, the volume of the plastic while liquid should be at least one and one half times the volume of the solid formed. Preferably,

Jan 1, 1947

By Sherman L. Pease

An inexpensive and relatively rapid method that can be used by field crews is described. Fluid movement is determined by releasing a tracer (dye) in the well at a predetermined level and, after an interval of time, sampling the well fluid at another level. The testing equipment consists of a combined crusher and sampler unit that is run into the well on a wire line. The rate of movement can be calculated from time-volume relationships. Description of Method It is often desirable to determine whether there is occurring any transfer of fluid from point to point in a shut-in well, and, if so, to measure the rate of movement. When it is desired to examine a large number of wells for possible "thief" sands, the time and expense will be considerable unless the method used is inexpensive and rapid. After experimentation with several possible solutions to the problem, the Production Department of the Shell Oil Co., Inc., developed the apparatus described herein, which has proved satisfactory. Routine operations with it can be carried out by field production crews with a minimum of technical supervision and with negligible investment in equipment. The method is based upon releasing a suitable tracer in the well fluid at a known level, and recovering a sample of well fluid at another level after a measured interval of time. Repetition of this process with different time intervals between release and sampling gives the necessary data. For purposes of illustration, the setup for measuring migration of fluid in an upward direction is described in the following paragraphs. The arrangement of equipment is shown diagrammatically on Fig. I. The elements of the combination unit are the tailpiece, the crushing device, the spacer and the sampling device. The lengths of the tailpiece and spacer are varied to place the crushing and sampling devices in the desired positions in relation to the sands being tested. The crushing device breaks the glass bottle containing the tracer when the tailpiece strikes the bottom of the well and the tension on the sand line is slackened. Because of the open construction of the crushing device, the tracer is quickly and completely disseminated in the well fluid. The sampling device is a suction bailer, which obtains a sample of the fluid surrounding the perforated nipple just before the unit is picked up off bottom. The sample is retained in the barrel by the ball valve for examination at the surface. Normally, on the first run into a well, the sample is obtained near the releasing point of the tracer, and thereafter samples are taken near the base of the upper sand if migration is indicated by the dilution or absence of the tracer in the initial sample. The length of the time interval between the releasing of the tracer and the sampling of the well fluid is varied for successive runs, attempting first to establish the rate within limits and then to define it more accurately by additional runs if necessary.

Jan 1, 1946

By P. H. Cardwell

The effect of various plastics upon the permeability of a sand and the mechanism of their ensuring permeability within the consolidated sand body is discussed. Data are presented on various properties of the plastic materials used in sand consolidation and the effect of temperature and usable temperature ranges are considered. The recovery of petroleum from uncon-solidated sands presents serious production problems, owing to sloughing of the formation. The solution of some of these problems usually has been by mechanical methods.' The ideal way of controlling the sloughing tendencies of these un consolidated formations, however, is to prevent the movement of the individual sand grains by the use of a bonding medium. A step in the desired direction was taken by Irons and Stcesser2 when they taught the use of liquid plastics to produce a consolidating deposit that prevents sloughing. More recently, Wrightsman and Buckley3 proposed a modification of this process. In this use of the liquid plastic, the sand grains become coated and the ensuing hardening of the plastic by polymerization or condensation cements together the sand Particles. Liquid plastics that have been suggested for this Purpose are of the following types: phenolformaldehyde, alkyd resins, vinyl type resins, polystyrene and the acrylic esters. When the flow of fluids through a sand must not be materially reduced, it is essential only to cement together the sand grains with liquid plastic and leave a portion of the interstitial space for fluid flow. TO be assured of obtaining fluid flow through the sand interstices after injection of plastic, it has been necessary in the past to remove the excess plastic from the interstices between the particles before it sets. Wrightsman and Buckley suggest two methods for the removal of the excess plastic from the interstices of the sand: (I) to flush the excess plastic back into the formation, away from the well bore, by use of oil or water; (2) to produce the well before the plastic has set, thereby moving the excess plastic into the well bore. Under certain well conditions it is very difficult to remove the excess plastic from all parts of the formation by either of these methods and leave the formation consolidated with no sections completely sealed. The method* described herein of retaining permeability within a sand body is to use a liquid plastic that upon setting ensures permeability within the consolidated sand body. This cements the sand grains but obviates the need for removing plastic from the interstices of the sand. One of the ways of accomplishing this is to use a liquid plastic that occupies a considerably greater volume than the solidified resin it yields on further polymerization or condensation in situ. In order to be satisfactory, the volume of the plastic while liquid should be at least one and one half times the volume of the solid formed. Preferably,

Jan 1, 1947

By M. L. Lissberger

entirely suitable for certain uses and even possess advantages over present solders at high temperatures, but they are certainly not suitable for all uses. However, it is conceivable that their use in many places will effect a material conservation of tin. It will probably be wiser to use cadmium in solders where good results have been obtained than in brass where this element will be a source of possible trouble. F. F. Colcord,* New York, N. Y.-—The cadmium-lead solder has a higher conductivity than the lead-tin alloy, which ought to make it advantageous in the manufacture of electrical machinery. In the case of solder for tin-can work, one of the high officials of the American Can Co. said that he fully intended to .give it a good trial, and I do not believe they are going to reach hasty conclusions and run the risk of poisoning the public. Solder, Its Use and Abuse Milton L. LissbeRgeR,† New York, N. Y.—Solder is a mechanical mixture of tin and lead, a fact which is susceptible of very simple demonstration. A bar of solder of a grade even as low as 30 per cent. tin and 70 per cent. lead, passed through a buffing machine, will show a surface practically identical with that of a bar of second-quality or reclaimed tin. The buffings, on chemical analysis, will prove to be almost pure lead. According to the best practice, solder is made in the following manner. Virgin pig lead is first melted, and when it is thoroughly liquefied, virgin pig tin is added, together with a small amount of flux; the latter is for the purpose of bringing to the surface the so-called "liver," consisting of impurities that may have remained in either the lead or the tin as a result of incomplete refining. The combined material, when completely liquid, is thoroughly stirred for some hours, and is then cast into small pigs. Just before casting, and continuously during this operation, the molten metal yields dross, consisting largely of the oxides of lead and tin; this should be carefully skimmed off. After the pigs have cooled, they are taken to a smaller kettle, re-melted, and cast into the desired shape for use; or if wires, ribbons, etc., are to be made, the solder is cast into slugs suitable for extrusion and rolling. During this second operation, the skimming of dross should be even more carefully done than at first. Hand mixing has proved to be the only reliable method for the production of the best quality of solder, irrespective of its percentages of lead and tin. The best quality of solder is not necessarily that which contains the highest percentage of tin, but rather is that composition which performs best on the required piece of work. In order to produce

Jan 1, 1919

By L. P. Davidson

The new electrolytic zinc plant of the American Zinc Company of Illinois commenced operation in April 1941. The simple flowsheet using the standard current density and the economic reasons that dictated it are given herewith. The Evans-Wallower Zinc Co. built an electrolytic zinc plant at Monsanto, 111., in 1929 and operated it for about two years. The plant stood idle from 1932 and was purchased by the American Zinc Co. in 1940. Because of the condition of the , equipment, excepting the motor generator set, a complete rebuilding was necessary. The Fairmont City plant of the American Zinc Co. could treat the leach residues, the purification cake and the skimmings from the melting furnace in its various plants. This possibility permitted a simple flowsheet with good economic results. The flowsheet is shown in Fig. I. The calcined concentrates are leached in mechanically agitated tanks with spent electrolyte and such ferric iron solution as necessary. When the acid has been neutralized and the iron coagulated, the fluid is discharged to settling tanks. The underflow from these thickeners is filtered on a Moore filter; the filter cake leaves the plant for retreatment and the filtrate joins the thickener overflow. Zinc dust is added to this solution until the copper and cadmium are precipitated. The pulp is filtered through shriver presses, which deliver the purified solution to stor- age tanks, and the copper-cadmium-zinc cake is shipped for retreatment snd recovery of these three metals. The purified solution is electrolyzed; the regenerated acid is returned for use in the leaching plant and the cathode zinc, after stripping, goes to the melting furnace, from which it is cast in slabs. The skimmings from the melting furnace are shipped to the Fairmont City plant for reduction to metal in the retort furnaces. The choice of this simple flowsheet was made possible only because of the facilities of the Fairmont City plant. The long leaching period, with high acid content and high temperature which characterize the high-density process, gives a higher zinc extraction but also dissolves more impurities, which must be removed. The same is true to a lesser degree of the multi-step leaching of the western low-density plants. By the sacrifice of some initial extraction, solutid'ns can be obtained that are relatively easy to purify and give good ampere efficiency. This loss in initial extraction is made up in the retreatment of the residues in the Waelz plant. The impurities that accompany the zinc thus extracted are inconsequential when the Waelz product is treated in a distillation plant. It was recognized that this flowsheet would require a somewhat greater amount of sulphuric acid—either as acid or as sulphate sulphur in the calcine—because of poorer washing. The sulphuric acid plant at Fairmont City could deliver 60" BC. acid to compensate for the sulphate loss and the cost would be less than the cost of more intensive washing.

Jan 1, 1944

By Edward Sampson, Allan B. Griggs

Surveying of many holes drilled by the U. S. Bureau of Mines in the Metaline district has shown surprising deviations. The holes start in the Ledbetter slate (Ordovician) and pass into the underlying gently dipping Metaline limestone (Cambrian) at varying depths, locally in excess of 1000 it. All holes start vertical, but one had deflected as much as 35° at a depth of only 300 it. One hole was found to be deflected 70' at a depth of 1000 ft. These deviations were not indicated to the drillers by any action of the rods or machines. Analysis of the survey data in the light of the observed geology indicates that the holes deviate most in the Ledbetter slate and scarcely at all in the Metaline limestone. The upper part of the "limestone'" in most holes is a massive rock strongly altered by hydrothermal action and essentially homogeneous. The slate is only obscurely bedded but has a cleavage, varying from slight to strong, which is unrelated to bedding. Drill holes have deflected to become nearly perpendicular to the cleavage. Several plans and cross sections are submitted showing the behavior of various holes. Introduction The Metaline district of northeastern Washington has received much attention recently and has promise of becoming even more important as a source of zinc than at present. Exploration has been conducted largely by deep diamond drilling, and in the course of this work it was found that holes became seriously deflected. This paper deals with the nature and causes of these deflections. The district lies along the Pend Oreille River in the northeastern corner of Washington, about loo miles north of Spokane, 9 miles from British Columbia, and 15 miles from Idaho. Three mines are now in operation and for a number of years have furnished a considerable production of zinc and lead. The ore contains zinc and lead in a ratio of about 31/2 to I, and occurs in the upper part of the Metaline limestone of Cambrian age, the upper member of which, where unaltered, is a rather pure limestone. This is overlain by Ledbetter slate of Ordovician age. Ore has formed by replacement of limestone, commonly 100 to 200 ft. below the slate, in areas of gentle dip, resulting in extensive tabular ore bodies. In and near ore, limestone has been intensely altered to granular dolomite and fine-grained quartz, which, where it predominates, forms "jasperoid." As part of their war program, the Geological survey and Bureau of Mines of the U. S. Department of Interior have been cooperating in an investigation of the district. The exploration by the Bureau of Mines in 1943 and 1944 was conducted largely by deep diamond drilling in which as much as 1000 ft. or more of Ledbetter slate was penetrated before the ore-bearing Metalin-2 limestone was reached. During the course of this drilling it was found that holes were seriously deflected while traversing the Ledbetter slate.

Jan 1, 1949

By L. A. Shipman

The combustion of coal in fuel beds has been practiced as an art for many years; during the last 2 7 years a scientific approach to this subject has contributed a small amount of fundamental data. The subject is a very controversial one. Opinions regarding the performance of the same coal used in the same equipment in different plants may vary from "the best coal ever used in the plant" to "the worst coal ever tired." These opinions can all be true, owing to the various conditions under which the coal was used. Because of these differences, an attempt will be made in this paper to discuss coal facts and coal characteristics as related to the use phenomena observed during the art of firing coal in fuel beds for many years. The work of Kreisinger1 and his associates in the 1,'. S. Bureau of Mines, reported in 1916, was the first scientific attempt I know of to obtain factual data explaining the mechanism of combustion of fuel beds. They gave a chart showing an ignited fuel bed. The air passing up through the fuel bed first combined with the fuel by a reaction resulting in the complete combustion of carbon to CO2, which combined with the carbon in higher levels of the fuel bed to form CO with the absorption of heat. The fundamental facts produced in those experiments proved of much value and checked with practical experiences with hand-fired fuel beds. Hand firing was the prevailing method of stoking coal at that time. The order in which these reactions occur, as shown by Kreisinger and his associates, has been amply confirmed by repetition of this work with different fuels both her? and abroad. These experiments also showed that under their conditions the rate of burning was proportional to the air flow. These data were of practical value to a fireman and were accepted as generally true in all fuel beds. In later years many observations by myself in fuel beds of underfeed stokers and other thick fuel beds such as gas producers, where channeling. increase of particle size, or both, occur. indicated that, instead of the horizontal layers we had thought were present, perhaps the layers were vertical or irregular. Later investigations in fuel beds made by Mayers2 and Barnes3 indicated that the burning takes place in some instances along the surfaces of vertical or irregular channels or cracks in the fuel bed and that under these conditions a reaction occurs that differs from that in the old horizontal-layered handfired fuel beds. Examining the data in Kreisinger'sl experiments, and the information in different charts with different fuels, different retort positions and air admissions of Barnes3 and the gas analysis arid isotherms of Mayers,2 one can check experience observation and come to a conclusion that as particle size of the fuel increases with other conditions the same, the maximum CO2 and temperature

Jan 1, 1947

By David Turnbull

In most reactions involving solids the transformation kinetics may be represented by the combination of two processes —those of nucleation and of growth. For example, Mehl and his coiq-orker in their studies on the transformation of austenite to pearlite in steels have been able to describe the kinetics in terms of the rates of nucleation and of growth. By micrographic examination of their specimens they determined the nucleation rate (rate of appearance of pearlite colonies) as a function of time, of percent transformation, and of temperature. They observed that after an incubation period in which no nuclei are observed, the number of nuclei appearing per unit time per unit of untransformed grain boundary area, increases at an increasng rate with time. When recrystallization rates have been interpreted in terms of rates of nucleation and growth and the rate of nucleation determined, an incubation period followed by an increasing rate of nucleation has also been reported. Among the studies in which this phenomenon has been observed are those of Kornfeld and coworkers3 on cold-drawn aluminum wire, of Anderson and Mehl4 n the recrystallization of aluminum sheet, and of Stanlcy and Meh15 on the recrystallization of silicon ferrite sheet. The existence of an incubation period during which no nuclei are observed does not appear to have been reconciled with the generally accepted Volmer-Becker theory of nucleation in condensed systems. This theory ostensibly requires the rate of appearance of nuclei to be independent of time. Volmer-Becker Theory In order to form a stable nuclcus of a new phase B in a mother phase A, the molecules or atoms of the mother phase must surmount a free energy barrier whose height is determined by the volume free energy change accompanying the transformation and the energy of the surface separating the two phases. The free energy difference between nuclei of various sizes and the molecules or atoms of the mother phase is plotted schematically in Fig I as a function of the radius of the nucleus r. This free energy difference is plotted for two values of the change of free energy per atom, (Jb — ja) accompanying the transformation when the volumes of the two phases are infinite. One of these values of (Jb—Ja) corresponds to a temperature above the temperature To at which the phascs A and B are in equilibrium, and the other to a temperature below To. In order for a nucleus of phase B to be stable at a temperature T² < TO, its radius must be equal to or greater than the critical value r* for which the free energy of formatioil of the nucleus is a maximum, the of phase B having radii equal to or less than r* will be called embryos hfehl and Jetter," in discussing the kinetics of nucleation in solid systems, suppose that embryos of critical size are formed

Jan 1, 1949

By R. M. Scafe

Although hydrogen has been intensively studied in its relation to steel quality, the methods of sampling and determinations are still open to question. It is true that various procedures have been proposed but actually there has not been sufficient agreement to establish a common base from which to work. As a result, it is difficult, to say the least, to correlate the reported results of some of the investigators in this field. The present symposium, premised on methods rather than effects, should prove of considerable value. For the purpose of this discussion two methods of sampling and analysis will be considered. First, sampling of molten steel in the ingot mold by use of an evacuated tube and cylinder using conventional methods of analysis for the gases collected; second, analysis by vacuum extraction involving the use of heating equipment and the determination of the amount of hydrogen evolved from solid steel samples by measurement at reduced pressures. Both methods have been used at Duquesne Steel Works and it is believed that either may be used with considerable benefit if the limitations of each method are recognized. Evacuated Tube and Cylinder Sampling devices for gases in molten steel suggested by various investigators range from very cumbersome and complicated devices to the relatively simple evacuated tube and cylinder used by Soler for deter- mining the CO content of the bath. This latter device was adopted (Fig. I) and modified to meet conditions at Duquesne Works. The principal modifications were in placing the cylinder at the side of the tube and the use of a sleeve on the immersion end of the tube. The first modification was made so that the cylinder could be readily detached and taken to the laboratory; the second, because of the difficulty encountered in obtaining an airtight seal after sampling and because of our practice of re-using the tube. Rigid control of the method of sampling and of the handling of the sample according to plan are of primary importance in hydrogen determinations. This applies to both the sampling of molten steel and the determination of the hydrogen content of cold steel samples. Except for a few preliminary samples taken from spoons, all work on molten steels using the evacuated tube was confined to the sampling and analysis of molten steel during the pour. As mentioned, uniformity of sampling was a basic consideration. As a result, every effort was made to follow definite sampling techniques and procedures. These included control of the depth below the surface from which the sample was taken, the timing between the shutoff and taking of the sample, as well as maintenance and care of the equipment. The distance below the surface at which the sample was taken was readily controlled bv means of a crosspiece and centering device attached to the tube. The steel was poured into the mold to the hot-top junction, the tube was then lowered into the 75

Jan 1, 1945

By L. A. Shipman

The combustion of coal in fuel beds has been practiced as an art for many years; during the last 2 7 years a scientific approach to this subject has contributed a small amount of fundamental data. The subject is a very controversial one. Opinions regarding the performance of the same coal used in the same equipment in different plants may vary from "the best coal ever used in the plant" to "the worst coal ever tired." These opinions can all be true, owing to the various conditions under which the coal was used. Because of these differences, an attempt will be made in this paper to discuss coal facts and coal characteristics as related to the use phenomena observed during the art of firing coal in fuel beds for many years. The work of Kreisinger1 and his associates in the 1,&apos;. S. Bureau of Mines, reported in 1916, was the first scientific attempt I know of to obtain factual data explaining the mechanism of combustion of fuel beds. They gave a chart showing an ignited fuel bed. The air passing up through the fuel bed first combined with the fuel by a reaction resulting in the complete combustion of carbon to CO2, which combined with the carbon in higher levels of the fuel bed to form CO with the absorption of heat. The fundamental facts produced in those experiments proved of much value and checked with practical experiences with hand-fired fuel beds. Hand firing was the prevailing method of stoking coal at that time. The order in which these reactions occur, as shown by Kreisinger and his associates, has been amply confirmed by repetition of this work with different fuels both her? and abroad. These experiments also showed that under their conditions the rate of burning was proportional to the air flow. These data were of practical value to a fireman and were accepted as generally true in all fuel beds. In later years many observations by myself in fuel beds of underfeed stokers and other thick fuel beds such as gas producers, where channeling. increase of particle size, or both, occur. indicated that, instead of the horizontal layers we had thought were present, perhaps the layers were vertical or irregular. Later investigations in fuel beds made by Mayers2 and Barnes3 indicated that the burning takes place in some instances along the surfaces of vertical or irregular channels or cracks in the fuel bed and that under these conditions a reaction occurs that differs from that in the old horizontal-layered handfired fuel beds. Examining the data in Kreisinger&apos;sl experiments, and the information in different charts with different fuels, different retort positions and air admissions of Barnes3 and the gas analysis arid isotherms of Mayers,2 one can check experience observation and come to a conclusion that as particle size of the fuel increases with other conditions the same, the maximum CO2 and temperature

Jan 1, 1947

By Edward Sampson, Allan B. Griggs

Surveying of many holes drilled by the U. S. Bureau of Mines in the Metaline district has shown surprising deviations. The holes start in the Ledbetter slate (Ordovician) and pass into the underlying gently dipping Metaline limestone (Cambrian) at varying depths, locally in excess of 1000 it. All holes start vertical, but one had deflected as much as 35° at a depth of only 300 it. One hole was found to be deflected 70&apos; at a depth of 1000 ft. These deviations were not indicated to the drillers by any action of the rods or machines. Analysis of the survey data in the light of the observed geology indicates that the holes deviate most in the Ledbetter slate and scarcely at all in the Metaline limestone. The upper part of the "limestone&apos;" in most holes is a massive rock strongly altered by hydrothermal action and essentially homogeneous. The slate is only obscurely bedded but has a cleavage, varying from slight to strong, which is unrelated to bedding. Drill holes have deflected to become nearly perpendicular to the cleavage. Several plans and cross sections are submitted showing the behavior of various holes. Introduction The Metaline district of northeastern Washington has received much attention recently and has promise of becoming even more important as a source of zinc than at present. Exploration has been conducted largely by deep diamond drilling, and in the course of this work it was found that holes became seriously deflected. This paper deals with the nature and causes of these deflections. The district lies along the Pend Oreille River in the northeastern corner of Washington, about loo miles north of Spokane, 9 miles from British Columbia, and 15 miles from Idaho. Three mines are now in operation and for a number of years have furnished a considerable production of zinc and lead. The ore contains zinc and lead in a ratio of about 31/2 to I, and occurs in the upper part of the Metaline limestone of Cambrian age, the upper member of which, where unaltered, is a rather pure limestone. This is overlain by Ledbetter slate of Ordovician age. Ore has formed by replacement of limestone, commonly 100 to 200 ft. below the slate, in areas of gentle dip, resulting in extensive tabular ore bodies. In and near ore, limestone has been intensely altered to granular dolomite and fine-grained quartz, which, where it predominates, forms "jasperoid." As part of their war program, the Geological survey and Bureau of Mines of the U. S. Department of Interior have been cooperating in an investigation of the district. The exploration by the Bureau of Mines in 1943 and 1944 was conducted largely by deep diamond drilling in which as much as 1000 ft. or more of Ledbetter slate was penetrated before the ore-bearing Metalin-2 limestone was reached. During the course of this drilling it was found that holes were seriously deflected while traversing the Ledbetter slate.

Jan 1, 1949

By L. M. Barker, E. G. Lewis

THE literature of milling is replete with papers devoted to the subject of ball milling, all of which no doubt have contributed in one way or another to progress in that art. In this paper reference will be made to only a few of the many authors, but the value of the contributions of all who have written on that subject is hereby acknowledged. With a few exceptions the efforts of most students of the subject have been devoted to laboratory investigations of principles. Davis1 was one of the first to report on plant-scale investigations and to present to mill men certain criteria for the guidance of ball-milling practices. His conclusions with respect to the significance of sizing analyses of classifier sands in their relation to the factors of mill speed and ball sizing are particularly referred to. Those conclusions were: I. If the balls are large or the speed of the mill is high, crowding will appear at the finer sizes in the classifier sands. 2. If the balls are small or the speed is low, crowding will appear at the coarser sizes in the classifier sands. 3. The indications are that best efficiency is obtained when the screen analysis of the sands show a minimum crowding at any size. The last conclusion was qualified by the statement that it had not been proved conclusively. It is surprising, however, that the literature of later years reveals little evidence that millmen have made any serious attempt to apply those criteria. This may, perhaps, be explained by the fact that the average plant-scale ball-milling problem presents so many variables that an investigation of any one of them encounters the problem of control of the others-a problem that often is unsurmountable in a small plant. In a large plant, in which there is a duplication of grinding units in parallel operation, opportunity may be afforded for determining the value of such criteria. Nevertheless, a study of published data from grinding circuits of both large and small plants suggests that either Davis&apos; criteria have been tried and found inapplicable or have never been given consideration. For the purpose of testing Davis&apos; conclusions and with improvement of ballmilling efficiency as the final objective, a test program was initiated in the concentrator of the New Cornelia branch of the Phelps Dodge Corporation early in 1938. The practices of that plant have already been described.2 The fine-grinding units are arranged so that any one of eight units may be operated as a test unit and its results compared with those of the remaining units. All units receive similar feed from a common storage bin, in which the product of the fine-crushing plant is bedded by traveling tripper. The ball mills are all similar in size and operated at the same speeds, and are individually metered. The feeder conveyors of each unit are equipped with Merrick weightometers. The test program as initially outlined proposed investigation of the following:

Jan 1, 1941

By James Terry Duce

In order to facilitate interpretation of the data in this chapter, we print the following excerpts from circulars to authors, compiled by Mr. Frank A. Herald when he was Vice-chairman for Production of the Petroleum Division: Generally in Table 1 the unit for presentation of data is a field. For our purposes a field is defined as the whole of a surface area wherein productive locations are continuous. Such unit commonly includes and surrounds nonproductive areas. Such unit commonly includes a great variety of geologic conditions-several units of continuous productive reservoirs of distinctly different structure and of distinctly different stratigraphy. Therefore it is hoped that our authors will subdivide "field" so as to enable students to make analyses that may have scientific and/or commercial value. As to each space in the tabulation, it is either (I) not applicable, (2) the proper entry is not determinable, (3) the proper entry is determinable, but not determinable from data available to the author, (4) the proper entry is determinable by the author. In spaces not applicable, the author will please draw horizontal lines; in spaces where the proper entries are not determinable, the author will please insert x; in spaces where the proper entries are determinable but not determinable from data available to the author, the author will please insert y; in spaces where the proper entries are determinable by the author he will, of course, make such entries. Generally, y implies a hope that in some future year a definite figure will be available. Inability to determine precisely the correct entry for a particular space should not lead the author to insert merely y. Contributions of great value may be made by the author in many cases where entries are not subject to precise determination. In such cases the author should use his good judgment and make the best entry possible under the circumstances. For many spaces, the correct entries represent the opinion of the author (for example, "Area Proved") and in such cases the entries need not be hedged to such extent as in cases where the quantities are definite yet can be ascertained only approximately by the author. In cases under definite headings but where figures are only approximate, the author may use x. For example, if the total production of a field is known to be between 1,800,000 and 1,850,000, the author may report 1,8xx,xxx; or if the production is between 1,850,000 and 1,900,000, the author may report 1,9xx,xxx. Where a numeral is immediately to the left of x or y, such numeral represents the nearest known number in that position. As to quantity of gas produced from many fields the question will arise as to whether the figures should include merely the gas marketed or should include also estimates of gas used in operations and gas wasted. Although rough approximations

Jan 1, 1938

By George A. Morrison

A deposit Of limestone Was known to exist at a depth of 2000 ft under the property of the Columbia Chemical Division of the Pittsburgh Plate Glass Co. at Barber-ton, Ohio. A 662-acre site was selected for the projected mine, some two miles northwest of the plant and near the main line of the Erie Railway. An electric railway 8800 ft in length connects the mine and the plant. The deposit is overlain by 18 ft of un-consolidated (sand and gravel), 100 ft of water-bearing sandstone, and finally 2080 ft of shale into which thin layers of sandstone are embedded. The limestone bed itself is 345 ft thick and overlies 200 ft of gypsum. A 300-ton-per-hour capacity mine was decided upon. Two shafts were deemed advisable, one for production and the second for service; and these were sunk 550 ft apart, one to a depth of 2323 ft and the other to 2258 ft. Each is 16 X , ft in the clear and timbered with 6-in. steel H-sets on 8-ft centers, using 3/8 X 4 X 4-in. angles as studdles. Twelve inch I-beams were used at 160 ft intervals as bearers set in deep hitches and concreted to a vertical depth of 8 ft. Wooden sheathing was first employed but sloughing of the shale created a pressure on this lining and finally concrete was deemed necessary. Water was encountered only within the first 315 ft, flowing at 60 gpm and by grouting this was reduced to 15 gpm. Temporary wooden sinking headframes were installed with 300 cu ft capacity storage pockets and with doors automatically controlled by air cylinders by hoistmen. Each shaft was operated on four 6-hr shifts. The usual V-cut was drilled at the center of the shaft and the round consisted of 34 holes- A 40 pet gelatin dynamite was employed with some 60 pet in the cut holes. Drilling crews consisted of four to six men. Shale drilled easily but became more bed in depth and sandstone wore away the gauge Of the bits rapidly. A room-and-pillar mining system was adopted whereby rooms turned off on 80-ft centers, each room 40-ft wide and 50-ft high. Rib pillars between rooms were cut into 100 ft lengths by frequent holes. Ventilation is achieved through the two shafts, the down-draft through the service shaft, and the return through the pr0duction shaft. The hoist has a a Of 300 tons per hour and is equipped with 10-ton balanced skips requiring. a 2-min cycle Or 30 trips Per hour- Hoisting is designed to Operate by automatic loading and no hoistman is required for normal Operation. The 48 X 60 in. jaw primary crusher is underground. It is fed through chute and chain feeders and is flood-oil lubricated and cooled. An inclined belt conveyor returns oversized material to the crusher. Tramming is by Diesel-powered trucks.

Jan 1, 1948