Search Documents

By D. A. Augenstein, L. V. Amundson

Operators of coal preparation plants use equipment such as large-capacity dump trucks and bulldozers to haul, spread, and compact refuse material to conform to federal and state regulations governing the disposal of solid waste. For example, federal regulations require that refuse be spread and compacted in layers not more than 0.6 m (2 ft) thick. If the refuse layers or piles have poor load-bearing characteristics, movement of equipment over them becomes extremely difficult. The increasing cost and limited space for the construction of settling ponds extensively used for fine refuse disposal are leading to the growing practice of dewatering the fine refuse by means of vacuum disk filters and combining the resulting filter cake with coarse refuse for waste bank disposal. However, this filter cake usually contains more than 25% moisture. Therefore, when it is combined with coarse refuse, the moisture level of the total refuse may become high enough to impair the load-bearing strength of the refuse. Precisely this problem and the attendant difficulties of moving heavy equipment arose when vacuum disk filters were installed at a preparation plant in West Virginia. Combining the moist filter cake with the coarse refuse generally results in a 12% moisture level for the total refuse at this plant. At this moisture level, the refuse can still be handled with some dif¬ficulty by the equipment. However, the problem has frequently been compounded after rains. The experimental program described in this paper tested the following methods of improving the load-bearing properties of coal refuse: moisture reduction, addition of crushed coarse refuse, addition of fly ash, addition of lime, and addition of a mixture of lime and fly ash. In terms of a balance between economic and technical considerations, the most effective method was demonstrated by laboratory and plant tests to be a 2% to 5% addition of lime. Test Program During formulation of a test program aimed at improving coal refuse stability, a number of treatment techniques were selected for evaluation of their effect on refuse load-bearing characteristics. The reduction of refuse moisture was the first technique considered, since moisture content plays a key role in the bearing strength of a bulk solid. The reasoning was that a very small reduction in refuse moisture, provided it could be accomplished with minimal effort and cost, would be sufficient for eliminating refuse disposal problems most of the time. At the same time, it was recognized that periods of rainy weather would offset moisture-reduction measures. Other techniques selected for evaluation because of their potential for improving refuse-bearing strength at reasonable cost were: addition of crushed coarse refuse, the addition of fly ash, and the addition of lime. A simple one-dimensional laboratory compaction test was designed for evaluating the effect of each of these techniques on refuse-bearing strength. Those techniques that gave best results in the laboratory would then be tested in the preparation plant in West Virginia. Laboratory Tests The laboratory test for evaluating each of the techniques involved the application of weight to a load module placed on a refuse sample in a container. The distance the load module sank with an increasing amount of applied weight was measured, and the relationship between module displacement and loading was obtained. The refuse container was large enough to minimize the influence of wall effects, and to decrease the effect of the container bottom, a test was terminated when the load module sank to about three fourths the depth of the container. Initially, an attempt was made to conduct compaction experiments with samples of total plant refuse. However, the presence of + 0.13 m (+ 5 in.) material in the refuse interfered with the mechanics of the test, and the large amount of material required for a representative sample made testing extremely tedious and time-consuming. To avoid this problem and because it was believed that only the fine components of the refuse were the major cause of the stability problem, tests were conducted with 13 mm X 0 (1/2 in. X 0) material from the total plant refuse. The equipment consisted of a 0.46 m (18 in.) cubic container, a loading module with 62 cm2 loading area, weights totaling 450 kg, and a portable concrete mixer for combining water and additives with the refuse. Refuse samples of about 110 kg dry weight were used for each test. Experimental compaction test data were evaluated by plotting the linear displacement of the load module vs. loading. During compaction tests, the vertical displacement of the load module was measured at each loading value. The plot of

Jan 1, 1980

By M. D. Arnold, P. B. Crawford, P. C. Hall

An experimental study has been made to determine the optimum flooding pressures for four different oils. The oil formation volume factors ranged from 1.08 to 2.13, and solution gas-oil ratios ranged from about 200 cu ft/bbl to 2,250 cu ft/bbl. Viscosities ranged from 0.38 to 0.95 cp at the respective bubble points of the fluids and from 0.7 to 20 cp at atmospheric pressure. Water floods were conducted at various pressure levels from run to run. The recovery as a function of flooding pressure was found to be different for each fluid, with optimum gas saturations ranging from 7 up to 35 per cent. The data indicate that substantially higher recoveries may be obtained if water floods are conducted at an optimum pressure and that this optimum pressure is a function of fluid properties. The same core was used for all tests, and the reproduction of saturations for various runs indicates that wettability in the predominantly water-wet core did not change. INTRODUCTION A paper was presented by Bass and Crawford' which described an experimental study of the effects of flooding pressure and rate on oil recovery by water flooding. This work was conducted using high-pressure models operated in a manner similar to that of an actual reservoir, with gas saturations being obtained by a solution-gas-drive mechanism. They found that the greatest oil recovery was obtained for the system studied by flooding in the presence of a 5 to 7 per cent gas saturation. Another experimental study simulating field conditions was presented by Richardson and Perkins.' They used an unconsolidated sand pack containing kerosene-natural gas fluid and interstitial water. They flooded at various pressures and flooding rates. For their system it was found that the recovery was independent of the pressure level at which the water flood was performed. Kyte, et al," found that oil recovery by water flooding was increased as the free gas saturation at waterflood initiation was increased. However, after the initial gas saturation was increased above 15 per cent, the increase in oil recovery tended to level off. All of their runs were made at the same pressure using a light oil saturated with helium. The desired gas saturation was obtained by injecting helium into the core. Dyes' made calculations which showed that an optimum gas saturation of 12 to 14 per cent may result in an increase in oil recovery of 7 to 12 per cent over that obtained by flooding at the bubble-point pressure. Others have also found that the presence of a free gas saturation may increase the waterflood oil recovery. In each case shrinkage was small and changes in fluid properties with respect to pressure were small. A careful review of the literature reveals that at the present time there is a wide difference of opinion on the factors affecting waterflood recoveries. This diversity of opinion is probably due to the fact that very little research has been done which has taken into account the many variables existing in an actual field being water flooded. Since the literature contains little information on high-pressure waterflooding studies using various types of reservoir fluids, it was believed appropriate that such a study should be made. EQUIPMENT AND PROCEDURE All tests were made using the same consolidated sandstone core. Torpedo sandstone was used to turn a cylindrical core 13.5-in. long and with a 2.92-in. average diameter. The core had a porosity of 28 per cent and a permeability to brine of 146 md. This brine was made up by adding 20,000-ppm sodium chloride and 30,000-ppm sodium nitrite to distilled water. This was used as connate water and flooding water. No fresh water was ever brought in contact with the core, as tests showed the sandstone contained argillaceous material which swelled in the presence of fresh water and plugged the stone. The core was sealed in a section of 6-in. N-80 tubing with Woods metal filling the annulus. The core was mounted horizontally; an injection well was placed in the center of one end and a production well in the center of the other. Pressure control was maintained by placing a back-pressure regulator (upstream control) on the producing well. The "live" oil was stored in a separate bottle and water was injected into this bottle to displace the oil for saturating the core using a two-cylinder standard-proportioning pump. This same pump was used for water flooding the core at a constant rate. This system was enclosed in water jackets and the temperature was automatically main-

By K. T. Aust

It is proposed that the intergranular corrosion of austenitic stainless steels is associated with the presence of continuous grain houndary paths of either second phase, or solute segregate resulting from solute-vacancy interactions. Experimental observations of structural changes and crrosion behavior of different types of austenitic stainless steel provide support for this poposal. On the basis of this model, it is shown that the intergranular -corrosion susceptibility of austenitic stainless steels in nitric-dic hromate solution may be substantially reduced either by suitable heat treatments or by impurity control. AUSTENITIC stainless steels, such as Type 304, generally have excellent corrosion resistant properties when properly solution heat-treated and used at temperatures where carbide precipitation is slow. However, several corrosion environments have been found which produce intergranular corrosion of solu-tion-treated stainless steels, that is, those steels with no detectable carbide precipitation.''2 Of the various corrosion environments, the most widely used test solution has been the boiling nitric-dichromate solution. In these acid solutions, stainless steels have been found to be susceptible to intergranular attack despite the addition of carbide-forming elements such as titanium or columbium, or despite lowering of the carbon content or use of high-temperature solution treatments. Studies of the electrochemical mechanism of corrosion attack have been made by several worke1s3'4 who found that oxidizing ions such as crt6 depolarize the cathodic reactions and consequently raise the open-circuit potential of stainless steel immersed in nitric acids. As a result of this, the anodic reaction is accelerated. The reason for the localization of anodic activity at the grain boundaries, and resulting intergranular corrosion, has not been conclusively determined. Several workers, e.g., Streicher,3 and Coriou et al.,4 have suggested that the strain energy associated with grain boundaries provides the driving force for the accelerated intergranular corrosion. This argument would predict that alloys of high purity would still be susceptible to intergranular attack. However, work by chaudron5 and by ArmijO,6 has shown that high-purity alloys are immune to attack, in disagreement with this argument. An alternative suggestion is that chemical concentration differences exist between grains and grain boundaries, that is, impurity segregation at boundaries, and that these chemical differences provide the driving force for localized attack. It is this impurity segregation which can lead to accelerated dissolution of grain boundaries when the alloy is exposed to a suitable corrodant. This mechanism would predict the immunity of high-purity alloys to inter-granular attack, which is in agreement with experi-mental observations. In the present paper, some recent studies on inter-granular corrosion of austenitic stainless steels which were conducted by coworkers and myself will be re-tibility A simple model will be described in which it is proposed that the intergranular corrosion of aus-tenitic stainless steel is associated with the presence of continuous grain boundary paths of either second phase or solute-segregated regions.* On the basis of this model, it is suggested that the intergranular corrosion rate can be markedly reduced by the formation of a discontinuous second phase at the grain boundaries if the discontinuous second phase incorporates the major part of the segregating solute, drained from the grain boundary region. Results are presented of corrosion tests and electron microscopic studies of different types of austenitic stainless steel after various heat treatments which provide experimental support for this model. Finally, a solute clustering mechanism, based on a solute-vacancy interaction, is shown to be consistent with the results obtained for inter-granular corrosion of solution-treated austenitic stainless steels. EXPERIMENTAL Corrosion tests using weight loss measurements were made on sheet specimens, which were lightly electropolished, washed, and immersed in boiling (115°C) 5 N HN03 containing 4 g crt+6 per liter added as potassium dichromate. Studies in which the inter-granular penetration depth was measured both by electrical resistance and metallographic methods have shown an empirical correlation between the rate of intergranular penetration and the weight loss per unit time for identically treated specimens of stainless steel." As a result, although all the corrosion data reported here are in terms of simple weight loss measurements, these data are considered to reflect primarily the rate of intergranular dissolution. Fig. 1 shows a typical result of intergranular attack of a solution-treated Type 304 stainless steel after 4 hr in a boiling nitric-dichromate solution. The wide grain boundary grooving at the surface, and the attack at incoherent twin boundaries, are evident; very little corrosion attack is seen at the coherent twin boundaries. INTERGRANULAR CORROSION MODEL

Jan 1, 1970

By P. B. Baxendell, R. Thomas

Work on the calculation of vertical two-phase flow gradients by Cia. Shell de Venezuela has been based mainly on the "energy-loss" method proposed by Poett-mann and Carpenter in 1952. The "energy-loss-factor" correlation proposed by Poettmann and Carpenter was based on relatively low-rate flow data. This correlation proved inapplicable to high-rate flow conditions. In an attempt to establish a satisfactory correlation for high rates, a series of experiments was carried out at rates up to 5,000 BID in Cia. Shell de Venezuela's La Paz field in Venezuela, using tubing strings fitted with electronic surface-recording pressure elements. As a result of these experiments a correlation between energy-loss factor and mass flow rate was established which is believed to be applicable to a wide range of conduit sizes and crude types at high flow rates (e.g., above 900 BID for 27/8-in. OD tubing). It is anticipated that the resulting gradient calculations will have an accuracy of the order of % 5 per cent. At lower flow rates the energy-loss factor cannot be considered as constant for any mass rate of flow, but varies with the free gas in place and the mixture velocity. No satisfactory correlating parameter was obtained. As a practical compromise for low flow rates, a modification of the curve proposed by Poettmann and Carpenter was used. In practice this was found to give gradient accuracies of approxirnately ± 10 per cent clown to flow rates as low as 300 B/D in 27/8-in. tubing. INTRODUCTION Production operations in Cia. Shell de Venezuela's light- and medium-crude fields are principally concerned with high-rate flowing or gas-lift wells. Under these conditions the analysis of well performance, the selection of production strings and the design of gas-lift installations are vitally dependent on an accurate knowledge of the pressure gradients involved in vertical two-phase flow. Initially, attempts were made to establish the gradients empirically as done by Gilbert,' but the results were not reliable due to scarcity of data over a full range of rates and gas-oil ratios. Several methods of calculation based on energy-balance considerations were attempted, but the computations were cumbersome and the results cliscouraging. In 1952 a paper was published by Poettmann and Carpenter' which proposed a new approach. Their method was also based on an energy-balance equation. but it was original in that no attempt was made to evaluate the various components making up the total energy losses. Instead, they proposed a form of analysis which assumed that all the significant energy losses for mutiphase flow could be correlated in a form similar to that of the Fanning equation for frictional 1osses in single-phase flow. They then derived an empirical relationship linking measurable field data with a factor which, when applied to the standard form of the Fanning equation, would enable the energy losses to be determined. The basic method was applied in Venezuela to the problem of annular flow gradients in the La Paz and Mara fields" This involved establishing a new energy-loss-factor correlation to cover high flow rates and, also, some adaptation of the method to permit mechanized calculation using punch-card machines. The final result was 1 set of gradient curves for La Paz and Mara conditions which proved to be surprisingly accurate. With the encouraging results of the annular flow calculations, several attempts were made to obtain a corresponding set of curves for tubing flow. Here, unfortunately, little progress could be made. The original correlation of Poettmann and Carpenter was based on rather 1imited data derived from low-rate observations in 23/8- and 27/8-in. OD tubing. It did not cover the higher range of production rates, and extrapolation proved unsuccessful. A new correlation covering high flow rates was required, but this proved to be extremely difficult to establish since tubing flow pressure measurements at high rates did not exist—due to the difficulty of running pressure bombs against high-velocity flow. The necessity for reliable tubing flow data increased with the development of the new concessions in Lake Maracaibo, where high-rate tubing flow from depths of 10,500 ft became routine. Thus. it was decided to set up a full-scale test to establish a reliable energy-loss factor for tubing flow conditions. A La. Paz field light-oil producer with a potential of approximately 12,000 B/D on annular flow was chosen. To obtain full pressure gradients, a special tubing string was installed which was equipped with electronic surface-recording pressure measuring devices,

By R. W. Ludt, C. C. DeWitt

The use of froth flotation for the separation of minerals has become one of the most important of ore dressing processes. Its particular adaptability to the enrichment of low grade ores has made the process an important factor in the national economy. The methods have been extended to the recovery of a great number of minerals. Among the few minerals which have resisted efforts toward industrial flotation is chrysocolla, a hydrated partly colloidal copper silicate. Chrysocolla, being a product of natural oxidation, has been found to occur in small quantities with many ores which are recovered by flotation methods. In present practice, these small quantities of copper silicate pass off with the tailings and are lost. The advantages to be gained by a satisfactory process for the recovery of chrysocolla is apparent. Any application of principles which points a way toward the satisfactory industrial flotation process for copper silicate would be of advantage. This paper presents an attack on this problem. Two methods for the recovery of chrysocolla have been developed by the United States Bureau of Mines.1,2 They have been successful on a laboratory scale but have been seriously restricted in industrial application by critical requirements in the procedure. In one of the Bureau of Mines methods,' the ore is activated with sodium or hydrogen sulphide in an aqueous solution at a pH of 4. Amy1 xanthate is then used as a collector with pine oil as a frother in the flotation process. An excess of sulphide acts as a depressant and the state of optimum conditions is difficult to control industrially. In the second Bureau of Mines method,2 soap is used as the collector at a pH of between 8 and 9. The diffi- culties with this process are that soap is not a specific collector, that heavy metal or alkaline earth ions cause the formation of insoluble soaps, and that a more acid solution causes the formation of a free acid which does not act as a collector for chrysocolla. The problem of recovering chrysocolla by flotation involves the selection of a suitable collector. The collector molecule must be composed of an active polar group that has an attraction for chrysocolla, and of a hydrocarbon chain. Certain dyes have been shown to have an attraction for certain minerals. Suida3 found that hydrated silicates are colored by basic dyes. Dittler4 showed that chrysocolla, among other colloidal minerals of acid reaction, preferentially takes up such basic dyes as fuchsin B, methylene blue, and methyl green. Endell5 gave information to show that the colloidal material in clay may be determined by its selective adsorption of fuchsin. A simple experiment, likewise, illustrates the difference in the adsorptive power of chrysocolla and of silica for the basic triphenyl methane dyes. When a mixture of chrysocolla and silica is immersed in a very dilute dye solution, less than 5 ppm, the chryso-colla is rapidly dyed and the silica is dyed more slowly. The difference is substantial but one of degree. Dean2 showed that the dyes, crystal violet and toluidine blue, are taken up by quartz in an adsorption type process. The difference in the adsorptive power, however, offers the means by which a new collector may act. To form such a collector, a hydrocarbon chain must be attached to the dye molecule. This involves a process of organic synthesis. Butyl, hexyl, and octyl hydrocarbon chains were selected for substitution in the malachite green molecule. For the purpose of identification, the alkyl-substituted dyes formed are called: butyl-malachite green; hexyl- malachite green; and octyl-malachite green. An outline of the procedure for their synthesis is given in the appendix. It is generally recognized in the preparation of this type of dye that the chemical structure of some of the dye molecules varies. However, a uniform formula is attributed to the dye. Such a procedure has been followed in specifying the structure of these alkyl-substi-tuted malachite green dyes. The structure is given on the basis of their properties as an homologous series of dyes, on their method of preparation, and on the purity of intermediates used. Structure of substituted alkyl malachite green is: C6H4 N(CH3)2 p-R C6H4 CH C6H4 N(CH)2 Procedure The flotation cell is a Bureau of Mines 100-g, batch unit provided with an air inlet at the bottom above which is a variable speed agitator. The agi-

Jan 1, 1950

By S. N. Singh, M. C. Flemings

Results are presented of a study on the combined influences of ingot dendrite am spacing and thermo-mechanical treatments on the fracture behavior and mechanical properties of high purity 7075 aluminum alloy. The most important single variable influencing mechanical properties was found to be undissolved alloy second Phase (microsegregation inherited from the original ingot). Ultimate and yield strengths were found to increase linearly with decreasing amount of alloy second phase while ductility increased markedly. At low amounts of second phase, transverse properties were approximately equal to longitudinal properties. In tensile testing, microcracks and holes were invariably found to originate in or around second phase particles. Fracture occurred both by propagation of cracks and coalescence of holes, depending on the distribution and amount of second phase. IN most commercial wrought alloys, second phase particles are present that are inherited from the original cast ingot. These include, for example, non-equilibrium alloy second phases such as CuAl2 and impurity second phases such as FeA13 and Cr2A1, in aluminum alloys. A previous paper1 has dealt with the morphology of these second phases in cast and wrought aluminum 7075 alloy, and with their behavior during various thermomechanical treatments. In this paper we discuss the influence of the particles on mechanical properties and fracture behavior of the alloy. Previous experimental work indicating a direct and major effect of second phase particles on mechanical properties (especially on ductility) includes the work of Edelson and Baldwin on pure copper.' Also relevant are the many studies demonstrating the important effect of nonmetallic inclusions on the fracture of. steel.3'4 Work on aluminum includes that of Antes, Lipson, and Rosenthal5 who showed that a dramatic improvement in ductility of wrought aluminum alloys of the 7000 series is achieved by eliminating second phases. It now seems well established that included second phases play a dominant role in controlling ductility (as measured, for example, by reduction in area in a tensile test) of a variety of materials. There is, therefore, considerable current interest in the mechanisms by which second phase particles affect ductile fracture. Experiments done by various workers have shown that second phase particles or discontinuities in the microstructure are potential sites for nuclea-tion of microcracks and of holes,6-l3 which then grow and cause premature fracture and the loss of ductility. Theoretical attempts have been made to explain the observed phenomena; most are able to explain observations qualitatively, but lack quantitative agreement. Much experimental work needs to be done to aid extension of theoretical models. A recent review article by Rosenfield summarizes work in this general area.14 PROCEDURE Material used in the previously described study on solution kinetics of cast and wrought 7075 alloy1 was also used in this study. Procedures for ingot casting, solution treating, and working were described in detail in that paper. Test bars were obtained for material of 76 initial dendrite arm spacing (11/2 in. from the ingot base) and 95 µ initial dendrite arm spacing (51/2 in. from the ingot base) for the following thermomechanical treatments (solution temperature 860°F; reduction by cold rolling). a) Solution treated 12 hr, reduced 2/1, 4/1, and 16/1. b) Solution treated 12 hr, reduced 16/1, solution treated approximately 5 hr after reduction. c) Same as a) except solution treated 24 hr prior to reduction. d) Same as b) except solution treated 24 hr prior to reduction. e) Same as d) except solution treated 20 hr after reduction. Test bars were taken both longitudinally and transverse to the rolling direction. Transverse properties are in the long transverse direction; since the final product was sheet (0.030 in. thick), properties in the short transverse direction could not be obtained. Test bars were flat specimens, of gage cross section1/-| in. by 0.030 in. and 1/2 in. gage length. After machining the test bars, they were given an additional 1/2 hr solution treatment of 860°F and aged 24 hr at 250°F. Three bars were tested for each location and thermomechanical treatment, after rejection of mechanically flawed bars. The average results of these three bars are reported. Elongation was measured using a $ in. extensometer and reduction in area was determined using a profilometer to measure the area after fracture. INFLUENCE OF THERMOMECHANICAL TREATMENTS AND SECOND PHASE ON MECHANICAL PROPERTIES Results of mechanical testing are presented in Figs. 1 to 4 and in tabular form in the Appendix. A general conclusion from results obtained is that details of the thermomechanical treatments studied were important only insofar as they influenced the amount of residual second phase. Figs. 1 and 4 show the longitudinal properties obtained (regardless of thermomechanical

Jan 1, 1970

By H. O. McLeod, J. M. Campbell

This paper presents the results of the data obtained in the first stage of a long-range study at high pressures of the system, vapor-hydrate-water rich liquid-hydrocarbon rich liquid. The data presented are for the three-phase systems in which no hydrocarbon liquid exists. Tests were performed on 10 gases at pressures from 1,000 to 10,000 psia. One of these was substantially pure methane, and the remainder were binary mixtures of methane with ethane, propane, iso-butane and normal butane. Several conclusions may be drawn from the data. 1. Contrary to previous extrapolations, the hydrocarbon mixtures tested form straight lines in the range of 6,000 to 10,000 psia which are parallel to the curves for pure methane, when the log of pressure is plotted vs hydrate formation temperature. 2. The hydrate formation temperature may be predicted accurately at pressures from 6,000 to 10,000 psia by using a modified form of the Clapeyron equation. The total hydrate curve may be predicted by using the vapor-solid equilibrium constants of Carson and Katz' to 4,000 psia and joining the two segments with a smooth continuous curve between 4,000 and 6,000 psia. 3. The use of gas specific gravity as a parameter in hydrate correlations is unsatisfactory at elevated pressures. 4. The hydrate crystal lattice is pressure sensitive at elevated pressures. INTRODUCTION Prior to 1950 many studies had been made of the hydrate forming conditions for typical natural gases to pressures of 4,000 psia.""'"'"" Most of these attempted to correlate the log of system pressure vs hydrate formation temperature, with gas specific gravity as a parameter. One of the more promising correlations was made by Katz, et al, which utilized vapor-solid equilibrium constants. The only published data above 4,000 psia are those of Kobayashi and Katz7 for pure methane to a pressure of 11,240 psia. In the intervening years, most published charts for the high-pressure range have represented nothing more than extrapolations of the low-pressure data, with the methane line serving as a general guide. The reliability of these charts has become increasingly doubtful (and critical) in our present technology as we handle more high-pressure systems. The portion of our high-pressure hydrate research program reported here was designed to: (1) investigate the reliability of existing charts; (2) obtain actual data on gas mixtures to 10,000 psia; and (3.) develop a simple hydrate correlation that was more reliable than those which simply used specific gravity as a parameter. Binary mixtures of methane and ethane, propane normal butane, or iso-butane were injected into a high-pressure visual cell containing an excess of distilled water. Hydrates were formed and then melted to observe the decomposition temperature of the hydrates at pressures from 1,000 to 10,000 psia. EQUIPMENT The equipment consisted of a Jerguson 10,000-lb high-pressure visual cell, a 10,000-1b high-pressure blind cell and a Ruska 25,000-1b pressure mercury pump. The visual cell was placed in a constant-temperature water bath controlled by a refrigeration unit and an electric filament heater. A Beckman GC-2 gas chromatograph was used in analyzing the gas mixtures after each run was completed. EXPERIMENTAL PROCEDURE After evacuating the gas system, the heavier hydrocarbon was injected into the high-pressure mixing cell to that pressure necessary to give the desired composition. This cell then was pressured to 1,100 to 1,200 psia by methane from a high-pressure cylinder. The mixing cell holding the gas contained a steel flapper plate and was shaken intermittently over a period of 15 minutes. After mixing, the valve to the high-pressure visual cell containing excess distilled water was opened, and the gas mixture was allowed to flow into the cell. The temperature in the water bath was lowered 10" to 15'F below the estimated hydrate decomposition point. As a first check, the temperature was increased at a rate of 1°F every six minutes to find the approximate point of decomposition. It was again lowered 1.5° to 5°F to form hydrates. The temperature was raised to within l° of the estimated decomposition point and then increased 0.2F every 10 to 15 minutes until the hydrates decomposed. This procedure was repeated at various pressures to obtain 7 to 13 points for each mixture between 1,000 and 10,000 psia. After completion of the hydrate decomposition tests, the gas mixture composition was analyzed with a calibrated gas chromatograph. These gas analyses have an estimated error of ± .1 per cent.

By P. Marier, T. R. lngraham

The kinetics of the sulfation of MnO,, MnzO3, and Mn3O4 in SO,, SO3, and O, mixtures was examined and the descending order of sulfation rates at temperatures near 400°C was found to be Mn,O3 > MnO, > Mn3O4. The respective activation energies for the thermal decomposition of MnO, and Mn,O, are 39 and 47 kcal. At 900°C, the thernzal decomposition of MnSO, to MnzO3 is slower than that to Mn3O4. The respective activation energies are 62 and 51 kcal, respectitely. MANGANESE is used to improve the hot workability of steel in the proportions of approximately 13.5 Ib of ferromanganese per ton of steel produced. This requirement accounts for about 95 pct of its large industrial market in North America. The remaining 5 pct is used in the battery and chemical industries. In most North American ores, the percentage of manganese and the manganese-to-iron ratio are not suitable for the direct production of ferromanganese. Hence, most of the North American requirements for manganese are satisfied by importing ore. Typically, many of the studies done on native low-grade manganese resources have been directed toward the production of ore substittes" and the recovery of manganese from open-hearth slags.3 Of the wide variety of processes which have been proposed, the most popular involve compounds in the Mn-S-O system. The thermodynamic properties of manganese and its compounds were reviewed by ah' in 1960 and, more recently, lngrahams discussed the thermodynamics of some of the reactions involved in the Mn-S-O system at normal roasting temperatures. The conditions for producing manganese sulfide during the reduction roasting of manganese sulfate are discussed by Fuller and Edlund.9 A novel scheme was proposed recently by zimmerley7 for utilizing waste sulfur dioxide from stack gases to recover the manganese from ocean-mined manganese nodules. Very little of the work published on manganese compounds has been related to reaction rates. Singleton et 1.' studied the rates of reaction on the MnO-C and Mn7C3-3MnO systems and observed linear and parabolic kinetics respectively in the systems. Tatievskaya et a1.' studied the low-temperature reduction of Mn&, MnO,, and Mn& in HZ and CO, and reported activation energies in the range 1628 kcal. In this paper, the rates of some of the decomposition and formation reactions involving MnSO4, MnOz, MnzO3, and Mn3O4 will be examined after the conditions for the thermodynamic stability of the individual compounds have been designated. CONDITIONS FOR STABILITY OF MnSO4, MnOz, MnZO3, AND Mn3O4 The areas of stability for h'hSO4, MnOz, MnzO3, and h3O4 were established from the data of Mah4 and Ingrahams and are shown in the predominance area diagram,10 logpq- logpsq, in Fig. 1. The diagram is drawn for two temperatures, 700°K, solid lines, and 1100°K, dotted lines. The sketch for the lower temperature includes the conditions likely to prevail in the Zimmerley patent7 when manganese nodules react with sulfur dioxide and that for the higher temperature indicates the conditions for recovering MnzO3 or Mn3O4 from MnSO4 during a roasting reaction. From the fact that the boundary between the areas of stability of MnOz and hSO4 at 700°K is parallel to the abscissa, it is evident that MnOz and SO2 should react together to produce MnSO4, irrespective of the oxygen pressure in the system. If the source of sulfur for sulfation were from waste flue gases, it is likely that the oxygen content of the gas stream would be more than sufficient to oxidize any MnsO4 to MnzO3, 107 atm of O2 required, or even to convert any Mnz03 to MnOz, 0.02 atm OZ required, prior to sulfation. At 1100°K, the diagram indicates that MnSO4 may be converted directly to either MnzO3 of Mn3O4, depending upon the prevailing partial pressure of oxygen. When the gas stream contains more than 1 pct Oz, logpq = -2, only MnzO3 would be recovered from an experiment done under equilibrium conditions. At oxygen partial pressures of less than 1 pct, one would expect to bring about a reversible exchange between MnSO4 and Mn3O4 by appropriate adjustment of the partial pressure of SOZ. These various reactions will be described in the subsequent kinetic experiments.

Jan 1, 1969

By C. N. Garman

Homestake-New Mexico Partners operate a 750-tpd carbonate leach uranium concentrate mill near Grants, N.M. The highly mineralized water available as process water leaves much to be desired. The 628 ppm as CaCO 3 makes the use of raw water very troublesome in pipes and on filter cloths. However, the residual sodium carbonate in the final filter cake going to tails makes an ideal softening agent. To take advantage of this fact, all makeup water used in the mill is first used as tailing slurry dilution water and comes to the mill from the tailings pond. The 5-acre tailings pond serves as a thickener and 100 to 150 gpm of nearly clear solution is decanted to a pump to be returned to the mill. Since this tailings water has small quantities of uranium in the solution an ion exchange scavenger unit was installed to remove as much uranium as possible. The ion exchange raffinate is then used as final filter wash ahead of the tailings slurrying step. In spite of the large settling area this return water is not clean enough for ion exchange feed. The solids present are very fine and composed of approximately 15 pct (by weight) burnable carbonaceous material common to the sandstone uranium ores in the area, 40 pct SiOz plus 45 pct CaC03. Laboratory work showed that this material responds very well to flotation. Before deciding to use flotation, various clarifying systems such as pressure leaf filters, sand filters, and continuous vacuum pre-coat filters, were considered. Each of these could have solved the problem but with much more operating labor, more reagents and greater installation costs than the flotation step. About 100 to 150 gpm of fouled water is fed to two 66-in. Fagergren cells, in series. Reagents used at the beginning were Arquad 2HT75 and Arquad C50, at the rate of about 1% lb per 8-hr shift, or about 0.0053 lb each per ton of ore. This did not completely remove the solids but does an acceptable job. Approximately 75 pct of the slimes are a size that can be caught on a 41-Whatman Paper are removed. Removal of these slimes also allows much better settling of the coarse nonfloatable material. Advantage is also taken of this fact in a small settling tank ahead of precipitation. Removal of this amount of the slimes makes the ion t:xchange feasible. PREGNANT SOLUTION CIRCUIT The carbonate? leach-caustic precipitation method of uranium concertration does not provide for any process purification step ahead of precipitation. Therefore, any fine solids getting into the pregnant solution through the filter cloth show up in the final concentrate. This, of course, lowers the grade, and, at times, the slimy nature of these very fine solids rendered final filtration of the concentrate difficult if not impossible At Homestake-New Mexico Partners a 75-ft thickener was available for gravity clarification of 100 to 120 gpm of this pregnant solution. However this did not sufficiently remove the slimes. Laboratory investigation of the whole range of flocculants that were suggested by literature, salesmen, and friends failed to turn up anything of consequence. A continuous vacuum pre-coat filter would do the job and was investigated. The capital cost and the operating labor and materials made this a last chance choice. Following work done in the metallurgical laboratory on the tailings return water, it was found that some changes in the reagent strengths and combinations made a very definite decrease in the solids in the pregnant solution. Concentrate grade improved about 5 pct anti the final product after drying had an appreciably greater bulk density. Compared to a cost of about 2.2e per ton for pre-coat filter opelation for cleaning just one circuit, flotation costs less than 1.0 per ton of ore for cleaning two circuits. While a pre-coat filter would do a more thorough job, the flotation does all that is required for either circuit. Gravity causes the froth produced to run back into the leach circuit. This does not appear to result in a build-up of objectionable slime. No extra manpower is required; the operators in the separate areas can observe the operation of the cells and mix the small quantities of reagents as needed. Normally the 66-in. Fagergren cell requires 15 hp per cell, but this very dilute slurry needs only 10 hp for both cells. Originally, a combination of the two Arquads mentioned previously served as frothers and promoters. As further testing

Jan 1, 1962

By J. K. Stanley

Knowledge of the diffusivity of carbon in the low temperature form of iron (alpha iron existing below 910°C) is at the moment of considerable interest in the study of the decomposition of austenite and martensite, the elastic after-effect,123 the magnetic after-effect4 and the decarburization of steel below 910°C. Information on the solubility of carbon in iron, and to a lesser extent its diffusion, is also important in consideration of such phenomena as blue-brittleness, temper-brittleness, "magnetic" aging, quench-aging, strain-aging, and possibly the yield point. In order to obtain more information on these subjects more fundamental knowledge is necessary. It is the purpose of this work to present data on the diffusion and solubility of carbon in the alpha iron. The high temperature form of iron (gamma; face-centered cubic) existing above 910°C is capable of dissolving relatively large amounts of carbon, up to 1.7 pet at 1130°C, while the low temperature form (alpha, body-centered cubic) existing below 910° dissolves only a limited maximum amount of less than 0.02 pet carbon at 725°C, according to data obtained here. Since the solubility of carbon in the face-centered or gamma iron is large, relatively speaking, no great analytical difficulties have been encountered in the determination of the solubility lines5 or of the diffusion of carbon.0 The limited solubility of carbon in alpha iron offers difficulties because experimental procedures and analytical methods for low carbon contents below say 0.01 pet have to be more refined than techniques used for work with gamma iron. Because of the difficulties of applying conventional methods to the determination of the diffusion of carbon in alpha iron, virtually no work has been done on this subject. However, by proper refinement of the analytical method for small amounts of carbon, the determination of the diffusion coefficient can be made readily using modified procedures. The solubility of carbon in alpha iron has been determined over a temperature range by various investigators, but the agreement among them is poor. The present investigation establishes the limits quite accurately. Information of this kind is useful in establishing the correctness of equilibrium diagrams but, more significantly, such information on maximum solubilities, especially when extended to alloyed ferrites, should be extremely important in the study of aging and related phenomena. Literature The literature existing on the diffusion, in particular, and on the solubility of carbon in alpha iron is not extensive. The data which exist are not of a high order of accuracy, much of them being in the realm of conjecture. THE DIFFUSION OF CARBON IN ALPHA IRON Whiteley7 made the qualitative ob- servation, using metallographic techniques, that the rate of diffusion of carbon at the A1 (725°C) point was very rapid and that its diffusion was still rapid at 550°C. Snoek,4 studying the magnetic aftereffect in high purity iron, arrived at the conclusion that the after-effect could be explained by the presence of small amounts of carbon diffusing under the influence of magnetostrictive strain (lattice distortion due to magnetic interaction). In later work, Snoek8 made an estimate of the ratio of carbon diffusion in alpha to its diffusion in gamma iron, and concluded that for a temperature of 910°C the ratio of Da/D? was 2600. Polder,9 basing his calculations of D on relaxation phenomena in the elastic after-effect, estimated that Da is about 1/3 of D? at 910°C (1183°K) and is about 1/12 of Dy at 727°C (1000°K). Polder's equation for the diffusion of carbon in alpha iron was calculated to be 18000 D = 5.2 X 10-4 e-RT cm2 per sec Ham10 obtained data for the diffusion and solid solubility of carbon in alpha iron at two temperatures by using one technique similar to that employed in this study. He found a D of 8.0 X 10-7 cm2 per sec at 702°C and of 2.7 X 10-7 at 648°C. THE SOLUBILITY OF CARBON IN ALPHA IRON Although pearlite is absent in steels containing 0.06 pet,11 0.05 pet,12 or 0.045 pet C,13 it appears that the carbon in these steels cannot be in solution in ferrite. The solubility of carbon at the A1 (725°C) point was first determined by Scott14 on the basis of cooling curves, and was found to be between 0.03 and 0.04 pet C. Tamura15 by interpolating between the solubility of carbon in delta iron at 1400°C and in alpha at room temperature (assuming zero solubility) ar-

Jan 1, 1950

By S. A. Lever, R. Hultgren

The solidus is usually the least satisfactorily determined portion of a phase diagram. Cooling curves, which succeed well with the liquidus, show the solidus inaccurately or not at all because of segregation which occurs during freezing. Heating curves of carefully homogenized alloys might be expected to indicate accurately the solidus, but they are seldom used. Dynamic methods involving heating or cooling are never completely satisfactory because of uncertainty as to whether equilibrium is attained. A static method in which the specimen may be allowed hours, days, or even weeks to attain equilibrium is to be preferred. In a static method a solid solution, for example, is first made thoroughly homogeneous, then heated to successively higher temperatures. After sufficient time at each temperature to assure equilibrium, some property is measured which should alter strikingly when melting begins. Microscopic examination can be used to detect the beginning of melting, but the method is tedious since the specimen must be quenched, sectioned, polished, and etched before each examination. Of all the physical properties which change on melting, electrical resistance is probably the most satisfactory to measure. The measurement may be made while the specimen is at temperature without damage to the specimen. It may be repeated indefinitely to ascertain when equilibrium has been achieved. Measurements may be made on a single specimen over the whole range of temperature. Most metals approximately double their resistance on melting. Since an accuracy of a few tenths of a percent is easy to achieve, the method is highly sensitive to the beginning of melting. In spite of these advantages, which have been perceived for a long time,l,2 a reasonable search of the literature has failed to reveal a single case in which the method has been satisfactorily applied in practice to the determination of solidus temperatures. The use of electrical resistance measurements appears to have been confined in practice to changes in the solid state. In the work described in the following pages we have applied the electrical resistance method to the solidus of the lead-tin system. We have found the method to be convenient, reproducible, and highly sensitive. We chose the lead-tin system because it leads to few technical difficulties. Furthermore, a number of determinations of solidus have been made in this system by various methods and results could be checked against them. However, all published results are not in good agreement with one another, so this work should help in determining the solidus more precisely. The Lead-tin Diagram Because of its commercial importance, there have been numerous investigations of the lead-tin diagram. The results of the most recent work on the solidus are indicated in Fig 7, as well as the results of the present work. The works of Honda and Abe3 and of Stockdale4 agree fairly well with each other and with the present work. Jeffery's5 data indicate the solidus to be about 50°C lower. Honda and Abe3 used differential thermal analysis on both heating and cooling cycles. Stockdale4 used the microscopic method and also differential heating curves. Stockdale's results were about 4" higher than those of Honda and Abe at low tin contents and lower at higher tin contents. These results also agree with those of Rosen-hain and Tucker.= Jeffery5 used electrical resistance measurements of the alloy as it was being heated or cooled. Apparently he did not attain equilibrium as his results are about 40°C lower than those of Stockdale4 or Honda and Abe.3 MATERIALS AND METHODS The lead and tin used were of high purity. They were supplied by the American Smelting and Refining Co., who gave the following analyses: Lead: silver, 0.0016 oz per ton; copper, 0.0008 pct; cadmium, 0.0007 pct; zinc, 0.0002 pct; arsenic, 0.0003 pct; antimony, 0.0002 pct; bismuth, 0.0005 pct; tin, 0.0001 pct; iron, 0.0020 pct; lead (by difference), 99.995 pct. Tin: antimony, 0.037 pct; arsenic, 0.020 pct; bismuth, 0.004 pct; cadmium, trace; copper, 0.025 pct; iron, 0.004 pct; lead, 0.020 pct; nickel and cobalt, 0.005 pct; silver, 0.0005 pct; sulphur, 0.005 pct; tin (by .-difference). 99.88 pct. One hundred grams of metal with the desired proportions of lead and tin was weighed out to the nearest one-tenth of a milligram. The mixture was placed in a silica crucible, covered with charcoal, and melted in a reducing atmosphere in a gas-fired furnace. The alloy was well stirred. Chemical analysis of two of the alloys checked closely with the weighed portions. The compositions of the remainder of the alloys were taken directly from the weighings, without chemical analysis.

Jan 1, 1950

By F. Weinberg

The relative concentration of 1" at grain boundaries in controlled orientation bicrystals has been examined by autoradiographic techniques, and by activity measurements of grain boundary surfaces exposed by preferential ,melting. The autoradio-graphs indicate that thallium is concentrated at grain boundaries in as-grown bicrystals, but not in zcell-annealed bicrystals. They also indicate that the solute concentration and the distribution on as-grown bicrystal surfaces are markedly different than that of the bulk material. The boundary surface measurements are in agreement with the autovadiographic evidence. On the basis of these measurements, as-grown bicrystals containing approximately 100 ppm of Tl, solidified at rates between 5 and 30 cm per hr and with tilt boundaries greater than 10 deg, exhibited grain boundary segregation equivalent to roughly 10 atomic planes of pure solute. Higher solute concentrations (equivalent to 140 atomic planes of pure solute) were obtained in bicrystals solidified slowly (0.6 cm per hr); slightly higher values were obtained in specimens containing a large angle nantilt boundary. Annealing for various times over a range of temperatures eliminated grain boundary segregation within the experimental uncertainty of the results (equivalent to 1 atomic Plane of pure thallium at the boundary). The results for the as-grown bicrystals can be qualitatively accounted for by assuming the presence of a groove on the solid-1iq;id interface, at the grain boundary. SOLUTE segregation at grain boundaries may be considered in two parts, namely, nonequilibrium segregation associated with the solidification process, and equilibrium segregation in fully annealed materials.' There is much indirect evidence for nonequilibrium segregation, based on preferential etching at grain boundaries and the mechanical properties of as-cast alloys. In addition, some direct observations have been reported in which radioactive tracers were used as solute additions and segregation detected at the grain boundaries by autoradiographic techniques. However, there is little detailed quantitative data on solute concentrations related to grain boundaries, particularly for different freezing conditions and grain boundary configurations. Equilibrium segregation at grain boundaries has been considered both theoretically and experimentally. cean' has made an estimate of the maximum equilibrium solute concentration that might be expected at a grain boundary, based on the lattice distortions in the boundary region. He arrived at a concentration which was equivalent t a monatomic layer of pure solute. A similar value, based on thermodynamic arguments, was calculated by Cahn and Hilliard for the segregation of phosphorus in iron. Experimentally, much higher values of solute concentration at grain boundaries have been reported recently by both Inman and iler' for phosphorus in iron, and Ainslie et 1.' for sulfur in iron. They observed concentrations equivalent to as much as 20 to 100 atomic layers of pure solute at the grain boundaries. However, in both cases it was shown that the observed segregation was not due solely to equilibrium segregation at the grain boundary. In the former case, precipitation effectss due to trace impurities in the material were believed to account for the large amount of solute present at the grain boundary. In the latter case it was shown that a high density of dislocations in the boundary region could provide a large number of additional sites for solute atoms, other than at the grain boundary. Thomas and chalmera have reported on the equilibrium segregation of po210 in grain boundaries of Pb-5 pct Bi alloys. Using autoradiographic techniques, they observed a concentration of polonium along the boundary trace on the surface of annealed bicrystal specimens grown from the melt. The concentration only appeared after annealing, and varied with boundary angle, increasing as the boundary angle increased. Their conclusions have been questioned by Ward," who pointed out that the segregation they observed along the boundary trace was much too wide to be compatible with the usual concepts of the thickness of a grain boundary of several lattice spacings. Also, Maroun et al.,l1 with specimens similar to those of Thomas and Chalmers, found that segregation could only be detected on the specimen surface, suggesting that Thomas and Chalmers' results were associated with an oxidation effect of polonium, and not equilibrium segregation. Thomas and Chalmers replied12 that they did observed segregation at the grain boundary in the bulk material and suggested further experiments were necessary to resolve the difference. The purpose of the present investigation was to examine both nonequilibrium and equilibrium grain boundary segregation in melt grown bicrystal specimens as a function of boundary angle, growth rate, and solute concentration, and to de-

Jan 1, 1963

By K. A. Slagle, D. K. Smith

weight obtained. Additives used in conjunction with salt in these slurries have included silica flour, calcium ligno-sulfonate and cellulose retarders, granular lost-circulation materials, bentonite and selected low-water-loss additives that are not significantly deteriorated by the presence of the chloride ion. In some other areas of South Texas, the salt-saturated slurries have been used quite extensively for improvement of the flow properties of slurries and attainment of better circulation characteristics at lower displacement rates. Concurrently with this property, the protection of shales and shaly sands is also realized, as well as useful retardation of the slurry. Resultant superior cementing jobs have been indicated by both communication tests and acoustic logs for bonding to pipe and formation.' In one section of Louisiana, a major oil company has been using salt-saturated API Class A cement with calcium lignosulfonate retarder for cementing through the Miocene at 9,000 to 10,000 ft. This is another of the situations where interbedding of sands and shales exists, creating difficulty in maintaining formation competency when a fresh-water slurry contacts the clay minerals of the formation. Further work has also been done in the shaly Miocene formation at 13,000 to 15,000 ft where fairly close water or gas contacts are encountered. Indications thus far are that better segregation of these various fluids is obtained by use of the saturated salt slurries because of their improved formation bonding characteristics. In addition to the properties of salt in this situation, attainment of turbulent flow at minimum displacement rates has also been accomplished by use of an additive to help provide exceptional dispersion and viscosity reduction of the slurry. Another oil company was encountering considerable expense in completing wells in Southwestern Louisiana due to extensive block squeeze requirements for effective separation of zones. A very effective mud program was being used to minimize washout in the shale sections and, apparently, a nearly gauge-size hole was being obtained. However, primary cementing results with fresh-water slurries were generally poor. On a few occasions when slurry was actually circulated to the surface, large pieces of shale formation were brought out of the hole with the slurry, indicating a severely water-sensitive, sloughing formation. Inhibition of shale heaving was being accomvlished in the drilling program, and immediately indone ipon circulation of the fresh-water slurry even though it contained a low-fluid-loss additive to reduce filtrate damage in the sands. The subsequent change to salt-saturated slurry yielded 11 successful primary cement jobs out of 12, compared to the previous success ratio of practically zero. Since these were deep, high-temperature wells in the range of 13,000 ft with high-pressure zones necessitating 17.5-lb/gal fluid densities, the slurry used was API Class E cement, silica flour, weight material, retarder, salt saturation (which also reduced the amount of weight material) and maintenance of low fluid loss by use of a salt-compatible additive. Other salt slurries have been used to a limited extent in this same general area for similar problems at depths ranging from 5,000 to 17,000 ft. In the shallower wells, the cement has usually been API Class A where the salt functions as a retarder, and in the deeper wells API Class E cement is used with the additional salt advantage being its increased slurry weight and inability to dissolve salt stringers. A considerable number of squeeze jobs have also been done on older wells using the salt-saturated slurries with very good results. MID-CONTINENT In North Texas, salt-water slurries have been used for cementing the Woodbine sand, Strawn sand, KMA sand and Pettit lime. Shales surrounding these formations have created the same difficulty in obtaining separation of producing zones that has been the problem in other areas. Depths in this area range from 3,400 ft for the Strawn to 7,400 ft for the Woodbine, and concentration of salt has varied accordingly. In the deeper wells, where retardation is desired, saturated salt-water cement is used; for the shallower wells, in order to provide shorter waiting-on-cement times, the amount of salt has been 18 per cent by weight of the mixing water. Results have been excellent with no reported failures on any of the salt cement jobs; where acoustic bond logs have indicated indifferent bonds previously, they are indicating very good bonding for the salt slurries. In Oklahoma various shales of Pennsylvanian age exhibit a high degree of sloughing in the presence of fresh water, causing severe washouts above and below sand formations which it is desired to isolate. This situation exists to some degree in practically all parts of Oklahoma and includes formations of other ages such as the Wood-ford shale. For the past few years, salt-saturated cements and displacement rates as high as practical have been used as a remedy for this problem, with very good results. The Layton and Bartlesville formations are two examples of shaly sands where saturated slurries have been helpful. In one area where five wells were drilled through this type of problem shale without obtaining a satisfactory primary cement job, a change was made to salt-saturated cement preceded by a suitable chemical wash for the drilling mud involved. Acoustic bond logging indicated excellent bonding, and final completion bore out this result by being trouble-free. This type of slurry has also been used extensively on squeeze jobs where shales have been heaving around the producing formations. Predominantly, the basic slurry has been either API Class A cement or a pozzolan cement—although, as deeper wells are being drilled, the use of salt in Class E cement is also increasing. Salt cement in West Texas has been used primarily to help prevent channeling through the shales around the Delaware sand, Queens dolomite and Hope lime. Many of the shaly and dirty sands of this area are sensitive to the filtrate from a fresh-water cement. Salt at 16 to 18 per cent by weight of mixing water has been added to centent, and has been effective in controlling formation damage and communication between zones in these formations. Use of these lower salt concentrations is dictated in this area by the relatively low formation temperatures where retardation of the slurry would create unduly long waiting-on-cement times. Also, quite a bit of cementing has been done in this area using salt concentrations in the accelerating range— that is, 2 to 5 per cent by weight of water. Specifically, these concentrations have been used in coiljunction with high percentages of gel to overcome the retarding effect of the calcium lignosulfonate dispersant, although there are probably several shales where these concentrations could provide some degree of formation stability. On several occasions, the salt has also been used to lower the critical velocity or rate for turbulence with the slurry, particularly in the pozzolan cements. On wells in the Hope lime, it has usually been necessary to squeeze the shale above and below the lime to get a water-free completion. Use of salt-saturated slurries has largely eliminated this

By R. E. Boni, G. Derge

Application of surface tension measurements has been made to molten silicates in order to determine the effect of sulphur upon the surface tensions of synthetic blast furnace slags. In melts with the same molar ratios of AI2O3 + SiO2 to the basic oxides BaO, CaO, and MgO, the surface tensions increase in the order of oxides listed. Sulphur lowers the surface tensions of the basic BaO, basic CaO, acid BaO, acid CaO, and acid MgO slags in that order; and the concentration of excess sulphur at the slag surface increases in this same order of slags. The rate and amount of desulphurization of iron by these slags is favored by a low excess surface sulphur in the slag. IN a previous paper,1 the authors discussed the applications of surface tension measurements of molten silicates to problems of metallurgical interest. Of major importance is the aid that such studies lend to forming a working concept of slag structure. Since the ability of a slag to desulphurize metal depends strongly upon its composition,2"4 fundamental information about the structural differences between various slags which contain sulphur should aid the development of better desulphurizing media. For that reason, the present investigation concerns the effect of sulphur upon the surface tensions of synthetic blast furnace slags. Experimental Procedure , The maximum bubble-pressure method was used to measure the surface tensions of synthetic blast furnace slags in the temperature range 1300° to 1600°C. The method is based upon the equation which was developed by Schrödinger5 from a consideration of the forces of hydrostatic pressure and surface tension of a liquid which oppose bubble formation when a gas is forced through a tube immersed in the liquid. where y is the surface tension between argon and slag in dynes per centimeter; g is the gravitational constant, centimeters per second2; H is the manometer reading in centimeters; s2 is the density of manometer fluid in grams per cubic centimeter; S1 is the density of the medium in grams per cubic

Jan 1, 1957

By James H. Bechtold

The yield strength of annealed tungsten was found to have a strain rate exponent 12 times as great as that of low carbon steel. The effects of temperature and strain rate could be correlated through the Zener-Hollomon parameter with a heat of activation associated with yielding of 32,000 cal per g-atom. This heat of activation is independent of strain although both the temperature and strain rate dependence of the yield strength vary with strain. MOST metals have mechanical properties that are relatively insensitive to strain rate, especially at temperatures below that at which creep is important. In iron and molybdenum," however, relatively large strain rate effects are observed in the temperature range where the rapid increase in yield strength occurs which leads to the ductile to brittle transition. In this temperature range Zener and Hollomon' have suggested that the effects of strain rate and temperature T on the yield strength could be correlated through a single parameter, P, in the following manner where Q is a heat of activation characteristic of the metal and associated with some unspecified relaxation process. They also observed that if the temperature is restricted to a relatively narrow range— below room temperature for steel—that the logarithm of the yield strength could be expressed as a linear function of the logarithm of P. From this relation the logarithm of stress should be a linear function of the logarithm of the strain rate at constant temperature: where r will be referred to herein as the strain rate exponent. At a constant strain rate the logarithm of stress should be a linear function of l/T, ay(e = C) ~ eT [4] where q = Qr [5] and is referred to herein as the temperature exponent. These equations have been found to relate the effects of temperature and strain rate on the yield strength of molybdenum in the temperature range wherein the ductile to brittle transition occurs, —75° to +150°C.2 Bechtold and Shewmon3 have shown recently that the ductile to brittle transition in annealed tungsten occurs in the temperature range +150° to +350°C. In this temperature range the yield strength in-

Jan 1, 1957

By C. W. Nicolson

The Tri-State zinc and lead-mining district is in the northeast corner of Oklahoma, the southeast corner of Kansas and the southwest corner of Missouri. The area throughout which active mining has been conducted is about 45 miles long and about 5 miles wide, extending northeasterly from Commerce, Okla., to Alba, Missouri. Although the lead ores were mined on a very small scale in the vicinity of Joplin, Mo., as early as 1848, nothing of any importance was done in the district until 1870, since when both mining and smelting have been prosecuted with considerable vigor. In the beginning the lead ores only were exploited, but within a few years extensive deposits of zinc ores were found and since that time the production of zinc ore has far exceeded that of lead. Both the surface and mineral rights in Missouri and Kansas were under individual ownership by the time ore was discovered. Although some of these rights were purchased by mining companies, most of the mining has been done under leases covering small areas, usually 40 acres, although in the past many leases were given on much smaller tracts. In Oklahoma most of the mineral land had been alloted by the Government to various Indian tribes and although the title to some of these lands had been acquired by various white men before the discovery of the rich Picher field, the title to most of the land has remained with the Indian tribes and the leasing of the mineral rights has been done by the Federal Government for the benefit of the Indians. The Indian allotments were of 200 acres each and some of the mining leases covered entire allotments, although many leases were granted for only 40 acres or even less. Practically all of the leases granted in the past required the erection of a concentrating plant on each lease, a condition that has had a pronounced effect upon the mining and milling methods of the district, since the apparent ore reserves on each tract were too small to justify large and elaborate mining and milling plants. Most of the leases were

Jan 1, 1940

By C. W. Nicolson

The Tri-State zinc and lead-mining district is in the northeast corner of Oklahoma, the southeast corner of Kansas and the southwest corner of Missouri. The area throughout which active mining has been conducted is about 45 miles long and about 5 miles wide, extending northeasterly from Commerce, Okla., to Alba, Missouri. Although the lead ores were mined on a very small scale in the vicinity of Joplin, Mo., as early as 1848, nothing of any importance was done in the district until 1870, since when both mining and smelting have been prosecuted with considerable vigor. In the beginning the lead ores only were exploited, but within a few years extensive deposits of zinc ores were found and since that time the production of zinc ore has far exceeded that of lead. Both the surface and mineral rights in Missouri and Kansas were under individual ownership by the time ore was discovered. Although some of these rights were purchased by mining companies, most of the mining has been done under leases covering small areas, usually 40 acres, although in the past many leases were given on much smaller tracts. In Oklahoma most of the mineral land had been alloted by the Government to various Indian tribes and although the title to some of these lands had been acquired by various white men before the discovery of the rich Picher field, the title to most of the land has remained with the Indian tribes and the leasing of the mineral rights has been done by the Federal Government for the benefit of the Indians. The Indian allotments were of 200 acres each and some of the mining leases covered entire allotments, although many leases were granted for only 40 acres or even less. Practically all of the leases granted in the past required the erection of a concentrating plant on each lease, a condition that has had a pronounced effect upon the mining and milling methods of the district, since the apparent ore reserves on each tract were too small to justify large and elaborate mining and milling plants. Most of the leases were

Jan 1, 1940

By J. Sharshall Grasty, Thomas L. Watson

The users of barite in the United States derive their supply partly from the domestic production and partly from the imports from foreign countries. According to the Mineral Resource division of the U. S. Geological Survey, the domestic production of barite in 1913 was 45,298 short tons, valued at $156,275, or $3.45 a ton, and the imports of crude barite were 35,840 short tons, valued at $61,409, or $1.71 a ton. These figures clearly show a decided advantage in cost of the foreign over the domestic barite to users in the United States. The difference in cost is the only advantage to the consumer of foreign barite, for there are large reserves of the mineral in the United States of good grade. The production of many of the operating mines is capable of decided increase, and it is believed that the operating mines together with the large reserves of undeveloped deposits of barite are entirely adequate to meet the demands of the users in the United States. Deposits of barite are known in California, Idaho, Nevada, and Alaska, but most of them are undeveloped because there is, apparently, no market for the material in that region. The domestic production is derived from Missouri .and the Appalachian States, the greater part being obtained from Missouri. Following the outbreak of war in Europe many users of foreign barite in the United States have been forced to seek their supplies at home. It seems opportune at this time, therefore, that a general review be given of the barite industry in the Appalachian States, one of the two areas from which the domestic supply of the mineral is derived, and that attention be directed to the undeveloped deposits in the region. Briefly, then, this paper reviews the barite industry in the Appalachian States, and describes the occurrence, preparation, and uses of the mineral. General Character Barite, known commercially as barytes or heavy spar, is barium sulphate (Baso4), containing when pure BaO, 65.7 per cent., and S03, 34.3 per cent. The specific gravity is 4.3 to 4.6, and the hardness 2.5

Jan 1, 1915

By Arthur C. Green

A group of 13 cities situated in Los Angeles and Orange counties in Southern California is engaged in constructing an aqueduct to carry water from the Colorado River at a point near Parker, Arizona, to a distribution point near Riverside, California. The aqueduct will have a total length of approximately 241 miles, and is designed to deliver 1605 cu. ft. of water per second, or a little more than one billion gallons per day. The aqueduct crosses a barren, desert waste and the project includes approximately 91 miles of 16-ft. tunnel. The large amount of tunnel driving that has been done in this country in the past few years has resulted in some remarkable developments in equipment and methods. The building of the Colorado River Aqueduct,, with its 91 miles of tunnels, has called on the best engineering knowledge in the country. New and better equipment has been designed for all phases of the work, and this equipment has been coordinated and adapted to the various conditions with a high degree of efficiency. The result has been that records for tunnel driving have been set under adverse natural conditions that exceed the estimates for progress under good conditions. All of the tunnels in the main aqueduct, except the Valverde and Bernasconi at the western end, have a finished diameter, inside the concrete lining, of 16 ft. Fig. 4 shows a section of the tunnel with the concrete lining in place. Fig. 5 illustrates the finished tunnel in three typical sections. The standard tunnel grade is 3.432 ft. per mile in the 16-ft. tunnels, but the Valverde and Bernasconi tunnels have a steeper grade and a finished diameter of 15 ft. 3 in. The rough bore of the large main aqueduct tunnels averages 12.95 solid cubic yards of material per foot of advance in timbered sections and 10.76 solid cubic yards per foot in unsupported sections. Tunnel Driving While the Conway mucker has been used on tunnel work for years, a larger and more powerful Conway was designed to meet the require-

Jan 1, 1937

By Oscar Glaeser

THE mine and plant of the United Verde Copper Co., located in Yavapi County, at Jerome, Arizona, have been described in various technical publications and, therefore, a brief outline of its essential features will suffice. The orebodies are of the schist replacement type, the main sulfide mass being a large lens-shaped body approximately 7 acres in cross-sectional area. In general, the mineralization is found along the iron-schist contact, with the orebodies extending-about 1000 ft. along this contact and varying from a few feet to 250 ft. in width. The mine is located on a mountain slope and has openings into it on three horizons, as follows: 1. Raises and ore passes open vertically into the shovel pit. These extend down to the 1000-ft. level, where they terminate as loading bins in the Hopewell adit. The main fan intake air shaft, which also extends vertically down to the 1000-ft. level, has its surface opening on the hillside at the extreme north end of the shovel pit, and the main mine air return exhausts through a raise at the extreme south end of the shovel pit. 2. The 500-ft. level adit. 3. The Hopewell adit on the 1000-ft. level. The mine has a vertical downward extent of 2000 ft. below the 1000-ft. level. Underground operations are carried on through two main shafts, both of which are wholly underground. Shaft 5 is the ore-hoisting shaft. It has three compartments and extends from the 800 to the 3150-ft. level. Shaft 6 is the service shaft, and is used for lowering and hoisting men and material. It has a large cage compartment and three smaller compartments for counterweights, ladderway, and pipe and power lines. This shaft extends from the 500 to the 2550-ft. level, and is now being extended to the 3000-ft. level. An air shaft for the downward movement of fresh air from the fan has been provided, and extends to the 2550-ft. level at this time. Work has been started to extend this air shaft to the 3000-ft. level. A return airway for vitiated mine air, in the form of raises and short connecting drifts, extends downward to the 2100-ft. level.

Jan 1, 1929