Search Documents

"The zinc concentrator of the Butte & Superior Copper company, shown on the opposite page, represents an industry which is coming into importance in Butte. The existence of large bodies of zinc ore in some of the silver veins of Butte has been realized for years, but it is only recently that some of them have proved amenable to successful concentration. Most of the zinc ores thus far found in the camp are mixed with considerable pyrite, but those found in the Black Rock and Elm Orlu mines contain very little pyrite, so that a concentrate low in iron is possible.The Butte & Superior mill is rated at 1,200 tons daily capacity. The ore is sphalerite, most of which is finely disseminated through a hard quartz gangue, with small quantities of galena, pyrite, chalcopyrite, rhodocrosite and rhodonite. In mining, the included granite and the low grade vein matter are sorted out and used for waste filling so that the ore as it goes to the concentrator will carry about 20 per cent of zinc, 1 per cent lead, .25 per cent copper, 8 to 10 ozs. silver and a little gold. The ore bodies ranging from 5 to 103 feet in width, are mined by the square set method and filling of stopes with waste rock.The ore is hard and tough requiring extensive crushing and grinding equipment, consisting of Blake and gyratory crushers, 54-inch and 42-inch high speed rolls, Chili mills, Tube, and Conical mills. All of the lead con¬centrate and part of the zinc concentrate are recovered in the upper part of the mill by jigs and tables. The classifier overflow and the re-ground jig and table tailings go to settling tanks and from there to the Hyde Flotation process, where the balance of the zinc concentrate is recovered, and the tailing go to waste."

Jan 1, 1913

By J. E. Powers, T. D. Taylor, N. E. Wood

A computer program has been developed to simulate a gas transmission 1ine operating under transient conditions. The program was developed by application of the basic mass and momentum balance equations. The nonlinear equations thus obtained were transformed by the method of characteristics and finite-difference techniques to make them suitable for machine computation. Three tests of the computer program were made. In each of these, the initial condition was assumed to be steady-state flow, the inlet density was held constant at the initial condition, and the outlet mass flow rate was varied with time. One test was theoretical in nature, but the others were made for direct comparison with actual field data. Results of the tests are presented in graphical form. INTRODUCTION Theoretical investigations of the transient flow of gas in long pipelines have been limited in number. In 1951, Olds and Sage4 developed a gaphical method of solving the nonlinear flow equations describing transient gas flow in a long pipeline. Research in this field at the U. of Oklahoma was initiated by Nelson1 in 1956. Nelson utilized a computer to solve numerical equations involving a lengthy trial-and-error procedure, and his results have been reported in the literature? It does not seem likely that Nelson's method can be extended to the analysis of transient behavior of pipeline networks; therefore, the investigation to be discussed in this paper was undertaken to improve and extend the previous work. The following discussion presents, briefly: (1) the basic differential equations governing transient flow, (2) transformation of these equations into a form suitable for machine computation. (3) role of boundary conditions in the calculations, (4) a very brief description of the computer program which was developed to simulate the pipeline and (5) results of tests of the computer program.

By George Smith

IN the utilization of natural resources owner, operator, and consumer should share the attendant benefits. Development needs to be planned under terms recognizing fully the interests of all concerned, for any undue advantage given to any one of these participants is apt to involve even greater and disproportionate injury to one or both of the others. For this reason it is well to preface any consideration of needed reforms in legislation affecting the disposition of public land with a survey of certain fundamental principles that determine the general conditions of all land transfers preliminary to development, utilization, and production. The disposition of any undeveloped natural resource, whether timber, oil, coal, or water power, as a transaction to which hand owner and prospective developer are parties, must be based in theory upon a division of expected returns. Whatever the terms of such disposition, neither party can reasonably ask for anything other than an equitable division of the returns. Under this analysis three and only three questions need to be discussed ; namely, what are those profits, how is this division to be accomplished, and what is the equitable basis of division ? The answer to the third question should probably be found by applying to the problem the principles of theoretical sociology, and' the question need not be mentioned further at this time, inasmuch as it does not involve the practical considerations to be kept in mind in connection with the other questions, which are concerned with only the measure of returns and their division. That is to say, whether the land owner's equity is to be stated as 95 per cent. or as 5 per cent. of the profits attending the development of the particular resource, no change would be necessary in the method to be adopted of arriving at the closest approximation of the prospective total profit.

Jan 10, 1913

By Darrel W. Hansen

Morrow Point Dam and Power Plant are principal features of the Bureau of Reclamation's Curecanti Unit of the Colorado River Storage Project. They are under construction on the Gunnison River 20 miles east of Montrose, Colo. Johnson-MK is the prime contractor, and represents a joint venture of Al Johnson Construction Co., Minneapolis, Minn., and Morrison-Knudsen Co., Inc., Boise, Idaho. The power plant will be housed in an underground chamber in the left abutment, approximately 250 ft behind the original canyon wall. The chamber is 206 ft long and 57 ft wide. The distance from the foundation to the spring line of the roof arch varies from 51 ft in the service bay to 120 ft in the control bay. The roof arch has a rise of 16 ft. The longitudinal center line of the chamber is orientated east-west with the draft tubes discharging nearly due north. Access to the power plant chamber was possible through the cable tunnel, access tunnel, two draft tube tunnels, two penstock tunnels, exploratory tunnel, which became the ventilation tunnel, or the grouting and drainage tunnel leading to the dam. (See Fig. 1.) The shortest and fastest access was through the cable and access tunnels, and the contractor drove these two tunnels simultaneously. The cable tunnel and cable gallery excavation exposed a transverse section, at the west end of the chamber, that was 15 ft wide and extended from the crown to 5 ft below spring line. It was here that arch excavation began. The first 34 ft of advance along the arch was driven on three headings, and the muck was removed through the cable tunnel. Meanwhile, the access tunnel was completed, and a raise was driven from its crown to intersect the advancing arch excavation near the longitudinal centerline

Jan 1, 1968

By S. Arthur Krom

ThE James diagonal-plane slimer is specially adapted to handle the finest slimes, but it will also handle sands as coarse as 40-mesh. The saving efficiency of this machine is due to the original construction ,of the deck, and to the rapid reciprocating movement imparted to it by the head-motion. The deck consists of a plurality of connected planes, having a certain fixed ratio of inclination one to another. These planes intersect each other diagonally to the stroke-line of the table and are arranged so as to give the pulp on the table a double treatment. This double concentration performed by the diagonal-plane deck produces cleaner concentrates and tailings than those obtained by the operation of two separate machines. The action of the diagonal planes settles, combines, and holds all the concentrates in one compact mass, sharply defined from the gangue, and easily cut away without loss. Many slime-concentrating machines distribute the feed-pulp for a distance of 4 or 5 ft. only, and upon a very limited settling-surface. This results in a thick, heavy deposit, from which it is impossible to stratify the values and wash away the gangue, the resulting products being dirty concentrates, and tailings carrying high values. The diagonal-plane slimer distributes the feed-pulp for a distance of 10 ft., and upon a settling-surface having an area of 40 sq. ft.; in other words, it spreads the pulp thinly on the table, which allows the metallic values to settle through the gangue quickly, forming a bottom stratum from which the thinly-distributed overlying stratum of gangue is easily brushed away by the feed-water without disturbing the underlying concentrates. Referring to Fig. 1, plane A is the main settling-section of the table. The feed pulp flows gently down this plane and is

Jan 1, 1913

By B. G. Ricketts, A. Kelly, P. A. Beck

The isothermal kinetics (at 200" to 400°C) of subgrain growth and of softening were studied in a 99.997 pct pure Al crystal rolled to 80 pct RA, under conditions where recrystallization did not take place. It was found that the kinetics of subgrain growth and of softening were similar, and that the correlation between subgrain growth and softening was in first approximation independent of the annealing temperature. It has been shown by Heidenreich' by means of electron transmission microscopy and by Hirsch and Kellar2 by means of an X-ray microbeam technique that the crystals of heavily cold-worked polycrystalline aluminum consist of subgrains of approximately 2µ diam, which are slightly disoriented with respect to each other. This substructure is found on cold working at room temperature, without annealing. A preliminary study has been previously published3 of the softening upon annealing at 350°C of a heavily cold-rolled aluminum single crystal. Softening and X-ray line sharpening for such a rolled aluminum crystal were later studied in more detail as a function of annealing time and temperature.4 Perryman5, 6 has studied the recovery of polycrystalline aluminum after cold rolling. By means of phase contrast microscopy he found that the subgrain size increases with the annealing temperature but does not alter very much with annealing time at a given temperature. In the present work further study was made of softening as a function of annealing time and temperature and subgrain sizes were determined by two different techniques in an attempt to find any correlation that may exist between softening and subgrain growth. Subgrain size measurements were made both by the X-ray microbeam technique and by transmission electron microscopy. EXPERIMENTAL PROCEDURE For the X-ray studies specimens were cut from

Jan 1, 1960

By Jerome Alexander

THE object of this paper is to show that many of the important phenomena of metals and alloys are due to the facts that, at some stage, metals and alloys, or some of their constituents, are in a colloidal state and that a portion of the metal or alloy tends to remain in this state. The so-called amorphous phase in pure metals is an isocolloid, consisting of colloidal groups of metal molecules that may be dispersed in still more finely subdivided metal; these colloidal particles are not truly amorphous, but may consist, in part, if not entirely, of ultramicroscopic crystals; as a result the expressions amorphous phase and amorphous theory might be replaced by the expressions colloidal phase and colloidal theory. Any substance is in the colloidal state when the constituent particles consist of molecular or atomic groups, whose size varies approximately from about 100µµ down to about 5µµ, that is from just below the limit of microscopic resolvability to the dimensions commonly ascribed to the larger molecules. Colloidality involves no assumption as to the shape, internal structure, or orientation of the colloidal particles; size alone is the critical factor. A colloidal system may therefore contain crystalline groups, or amorphous groups (non-crystalline, random or haphazard clusters), or a mixture of the two. All colloids consist of at least two phases, the subdivided substance, or dispersed phase, and the substance into which this is subdivided, the dispersion medium. It is not necessary that there be any chemical difference between the dispersed phase and the dispersion medium. As molecular forces are extremely powerful, their application may produce marked changes in the physical properties of metals. It is doubtful whether metal in the interior, especially of large masses, possesses the same properties as that on or near the surface, which alone is open to, inspection.

Jan 10, 1920

By Walter G. Perkins

In the assay of copper-bearing material for gold and silver, the elimination of copper before the final cupellation is of course essential, because any copper left in the lead-button will carry gold into the cupel; and a method which will effectively remove the copper with the smallest amount of manipullation is desirable. The scorification method is often rendered long and tedious by the necessity of repeatedly re-scorifying the button— to say nothing of the risk of losing Au—Ag thereby incurred. An ore carrying, for instance, 10 per cent,. of copper and only 0.1 or 0.2 oz. gold per ton, cannot be scorified with accurate results, because so many portions would have to be taken in order to get enough gold for weighing. On the other hand, the crucible method, with potassic nitrate and nails, would not do at all in such a case, because all the copper would be reduced by the nails, and (if the charge were 0.5 A. T.) this would defeat cupellation, by causing cupel-absorption of gold. In matte-assays, more concentrated value permits the determination of gold from smaller portions, and thus diminishes the difficulty experienced with ores. The method here described has been severely tested, during use for more than a year, and hart never failed hitherto, in the assay of any ore or product to which it has been applied. It is not proposed as perfect for every variety of ore or matte—probably no method would be that; but it is believed that, intelligently used, with the modifications dictated by practice, it will give better results, with less expenditure of time and labor, than any other known to the writer.

Jan 1, 1902

By Damon H. McFadden

5.1-1. Geographic and Geologic Factors. Surface mines are located where the coal seam can be economically uncovered and where the product can be utilized competitively with other fuels. The planning and designing of a pit may follow various procedures. The sequence for consideration of the influential factors as considered here may not be complete for every pit, nor will it be necessary to be completely used in each design. It is suggested as a check and outline for the engineering approach. Controlling conditions for the layout should be listed and considered with the facilities and equipment for the exploitation. After these items, as listed below, have been discussed and the feasibility agreed upon, then the actual planning and design of the pit can be done. GEOGRAPHIC FEATURES. The location of the coal area sets the climatic stage. The rainfall, the temperature extremes, and the general weather conditions all affect the design of the pit. Overburden soil when wet may not be stackable and may be impossible to move by standard procedures. The coal seam itself may be so soft that it must not be traveled on when wet, as the losses may be the difference between a profitable venture and an unsuccessful one. Some equipment will work well on dry soil only, just as a dredge works only in the wet. The conditions must be checked and analyzed. Some equipment cannot handle frozen soil (wheel excavators), so temperature extremes must be noted. The extreme weather conditions may also govern the expected working days and therefore the ultimate production. The altitude (atmospheric pressure) may affect the equipment, and this should be checked. All of these conditions should be noted on the preliminary map of the area. GEOLOGIC FACTORS. The geologic and surface conditions of the coal field dictate the type of pit generally feasible. Rough terrain, rolling terrain,

Jan 1, 1968

By Rodney P. Smith

The rate of motion of the boundary between a single-phase a-iron region and a two phase a-iron plus ?-iron, or a-iron plus cementite region has been measured on decarburization at several temperatures between 500" and 865°C. These data, together with data for the carbon content of a-iron at the boundary, yield the diffusivity of carbon in a-iron. The activation energy for carbon diffusion is 19.8 kcal per mole for the temperature range —50° to 150°C and increases to an average value of 23.0 kcaL per mole for the temperature range 727" to 865°C. AS part of an investigation of the diffusivity of carbon in iron using a steady-state method,' the diffusivity of carbon in a-iron was determined at the temperatures 802" and 851°C. The diffusion constant thus obtained was larger, by nearly a factor of two, than that predicted from the combined results of stanley2 and of Wert.3 It seemed desirable, therefore, to continue the investigation. Since the temperature range in which the steady-state method can be conveniently used is limited, we have chosen a decarburization method, based on the laws of diffusion in metal accompanied by a phase change.4,5 If the initial carbon content of the Fe-C alloy is such that two phases coexist at the decar-burizing temperature* and decarburization is car- ried out such that the surface is maintained at substantially zero wt pct. C, the carbon distribution after a time, t, will be as shown in Fig. 1. The boundary between the single-phase and two-phase regions moves from y = 0 to y = x in the time, t, where x is proportional4 to tl". If the initial carbon (content of the sample is Ci, and CB is

Jan 1, 1962

By Edward Hyde

THE HIGH-TEMPERATURE SCALE IN OPTICAL PYROMETRY AT the basis of optical pyrometry lie the theoretical and experimental data of the so-called blackbody. The black body is essentially a theoretical conception, with certain simple properties attributed to it -fundamentally, the property that its radiation at any temperature is a unique function of the temperature and does not involve any other variables. As a theoretical conception, an equation has been developed by Boltzmann connecting the total radiant power with the temperature, and another equation by Planck connecting the distribution of radiant power throughout the spectrum with the temperature. The integral of the latter with respect to wave-length conduces to the former and permits the evaluation of the constant c1 of the Planck equation, ass given in the form. J-= cl?-5 c2 (1) e ? T ? 1 assuming that the constant Q of the Stefan-Boltzmann law E=a(T4-T40) is known. The other constant c2 is arrived at by other methods, which will be discussed later. This equation for the black body lies at the foundation of optical pyrometry. To make the discussion complete, it should be stated that the theoretical black body is quite closely realized by a hollow enclosure with walls at a uniform temperature and radiating through a small orifice. The electrically heated black body, first introduced by Lummer and Kurlbaum, is an essential part of the equipment of a pyrometric research or testing laboratory. Numerous investigations have shown that its radiation conforms to that of the theoretical black body within experimental errors. Hence by operating the electrically heated black body at the melting point of some pure metal for which the temperature of melting has been determined on the vas scale. a standard is obtained for comparison with

Jan 9, 1919

By Claude H. P. Lupis, John F. Elliott

The classic Siez~erts' technique has been employed to determine the solubility of oxygen in liquid pure silver and the effect on the oxygen solubility of solute metal additions to liquid silver. The results indicate that oxygen deviates slightly from Sieverts' law in pure silver as = 3.9. Gold, platinum, md palladium decrease the solubility of oxygen in silver. First-order free energy, enthalpy, md entropy interaction coefficients are determined from the data. An important aspect in the establishment of the formalisms to be applied to represent the thermody-namic behavior of components of solutions is the accuracy of the experimentally determined thermody-namic properties. Wagner developed the first-order free energy interaction coefficient.' Recent papers2'3 extend the treatment formally to other thermodynamic properties and define the second- and higher-order interaction coefficients. A current communication4 considers in some depth the requirements and limitations imposed because of experimental error on the use of several formalisms now under active consideration in the field. This communication reports the results of an experimental study of the behavior of oxygen in liquid silver alloys that was carried out concurrently with the development of Refs. 2 and 3 with the hope of providing sufficiently precise information so that enthalpy and entropy interaction coefficients could be determined. THE EXPERIMENTS The Sieverts technique was employed using an improved design of the reaction bulb over that developed originally by Humbert5 and subsequently improved by pehlke6 and Weinstein.7 The Vycor reaction bulb as shown in Fig. 1 was air-cooled and contained a port for the thermocouple angling off to one side and a vertical port for connections to the gas supply and

Jan 1, 1969

By J. I. Drever, C. R. McKee

The push-pull test, which is a simple injection and pumping sequence of ground water spiked with solutes of interest, is presented as a method of determining the adsorption characteristics of a formation. Adsorption properties are necessary to predict restoration from both in situ coal gasification and in situ uranium extraction. The major problems in applying laboratory measurements to the field concern scaling the effect of particle size, and obtaining representative samples. Laboratory measurements are conducted on gram to kilogram scale samples, whereas the push-pull test evaluates a sample weighing approximately 130 to 1,000 metric tons, depending on volume injected and porosity. The problems in translating laboratory results to the field appear to be less severe for sedimentary uranium bodies than for coal. Laboratory measurements are useful in delineating possible ranges in adsorption properties, and in planning the field experiment. The adsorption properties of a formation are characterized by the cation exchange capacity (C) and the distribution coefficient measured at low concentration, (kd) 'Laboratory procedures for their measurement on coal and uranium ore are reported. Two field push-pull tests were conducted on uranium formations in Wyoming. Adsorption properties estimated from these tests on the basis of a simple cell model were compared to the laboratory values. In the first case, excellent agreement was observed between the values estimated from the field test and the values measured in the laboratory. In the second case, the value for kd determined in the laboratory was 5 times higher than the field value. It is recommended that push-pull tests be conducted on coal formations being considered for in situ gasification in view of the great uncertainty in extrapolating 1aboratory.adsorption properties to the field.

Jan 1, 1979

By Frederick Clapp

ALTHOUGH many oil fields have been, and still are being, discovered in Oklahoma, the geology and structure of most of them have not become familiar to the general public because of the delay in securing government geological surveys and the reluctance of oil companies and other interested parties to give out their "inside information." Therefore, until official surveys are available, it behooves us to publish geological results as soon as possible. Fortunately the writer has been authorized by the Cement Field Oil Co. to publish his data on the Cement field, Caddo County at this time. LOCALITY AND DESCRIPTION The Cement field is situated in the part of Oklahoma known generally, until recently, as "Healdton fields," and lies 60 mi. (96 km.) northwest of the Healdton field proper. Like the Healdton field, it forms an approximate ellipse, trending northwest and southeast through the village of Cement on the St. Louis-San Francisco Railroad, on which it is reached in 2 ½ hours from Oklahoma City. In its geological structure, the field constitutes an anticline over 13 mi. (21 km.) long and from 1 to 3 mi. wide; the point of greatest width being not far from its intersection by the above-named railroad. The major axis trends north 75° west from the village of Cement; but eastward appears deflected (if field interpretations are correct) to about south. 45° east. About 5 mi. south lies an approximately parallel syncline, which may be conveniently called the Cyril syncline, the south and west boundaries of which may be distant many miles, but forming a closed basin', south of the Cement anticline. The position of the offsetting synclinal axis, which is believed to lie north and east of Cement, has not been discovered.

Jan 2, 1920

By Oscar A. Glaeser

The purpose of this paper is to present specific applications of the fundamental principles of mine ventilation and the means that are at our disposal to accomplish the task of maintaining a healthful atmosphere in small mines and prospect openings. Need for Ventilation The range between the maximum oxygen content of normal air and the minimum safe content is extremely narrow, approximately 5 per cent. Furthermore, normal air must not be contaminated with irrespirable gases beyond definite limits, and mineral dusts are equally dangerous, although health impairment is slower. Tables 1 and 2 present the more common respiratory hazards encountered in mines. Adequate ventilation is the most effective means available to reduce or eliminate these hazards. Mechanical ventilation has reached varying stages of perfection in coal mines and in many large metal mines. The small mines and prospects rarely have a definite plan of ventilation. As a consequence underground workers are frequently exposed to health and accident hazards. The annual reports of fatalities in mines in the Western States record yearly many deaths due to asphyxiation and deaths caused by men falling down shafts and raises after being overcome by gas. At times mining operations are slowed up because there is no means of driving out the gas after blasting. For that reason only one shift is worked, or men wait from one to several hours for the "smoke" to clear out. Methane gas in varying quantities is widely distributed throughout California. It has been encountered in explosive concentrations in the coast range. It has been found on the Mother Lode and in quicksilver mines near the coast. Methane explosions have not been uncommon in underground operations and in tunneling jobs. These conditions and records indicate that there is room for improvement in mine-air conditions.

Jan 1, 1937

By Courtenay DeKalb

Revision of the United States mining law is needed chiefly because of the following reasons: 1. The conceptions as to the characteristics of orebodies that were held at the time the statute of 1872 was enacted have since proved to be in many respects erroneous. 2. The operation of the existing law has been found to work unnecessary hardship upon many claimants to mineral land. 3. The existing statute fails in large degree to encourage development of mineral resources. 4. The existing law often produces conflict between placer and lode-claim rights, working unnecessary injustice to placer claimants. 5. The methods of establishing the rights of locators on United States mineral land are defective, and are not uniform throughout the States within which such lands exist. Law of the Apex The objections to the so-called "law of the apex" are so well known as to require no detailed statement. It is sufficient to point out that the apex rule was based upon the notion that ore deposits consisted of well-formed veins included between definite walls, like the slice of ham in a sandwich. The fact is that veins conforming to that simple type are rare. Irregularity is the rule, and the chief metal production of the United States comes from mass? which bear no resemblance to the tabular form of vein. Manifestly the law of the apex fails completely in such cases. Moreover, the tendency is constantly toward the exploitation of ores of lower grade than could formerly be worked, and such deposits exist mainly in the form of large irregular impregnated zones and masses, so that the future development of our mineral resources would be continuously embarrassed by shadowy claims to extra-lateral rights by the locators of so-called apexes.

Jan 1, 1915

By J. J. Gilman

WHEN a cleavage crack that is moving through a crystal intersects a screw dislocation, a jog is created in the crack front. As the crack continues to move, the jog leaves behind a cleavage step. This mechanism was proposed by Amelinckx and Votava,' Pratt, bnd Gilmanh t about the same time. At that time the evidence for the mechanism was largely indirect. Other evidence has been presented by Low, Bilby and Smith,5 and Forty.' It is the purpose of this paper to present more direct evidence of this mechanism and to show that observations of cleavage steps can be used to detect screw dislocations. Experimental Lithium-fluoride crystals that were purchased from the Harshaw Chemical Company, as well as natural mineral crystals and metal crystals, were used in the experiments. Although cleavage steps can be observed on transparent crystals with a metallurgical microscope, the contrast is poor. Marked improvement in the contrast is obtained by depositing thin (1000A) films of silver or aluminum onto the surfaces. The contrast also can be improved by using a phase-contrast microscope, but the simpler silvering method gives just as good results. Tolansky interferometric microscopy, and electron microscopy were used to measure the heights of cleavage steps. The etching techniques developed by Gilman and Johnstonh ere used to detect dislocations in the LiF crystals. Results The dislocations that create cleavage steps can originate in three ways: a) They can be grown into crystals b) They can be introduced by plastic deformation prior to cleavage c) They can be formed just in front of the tip of a propagating cleavage crack.' These three situations will be considered in turn. Grown-in Dislocations—It is not possible to see the individual monomolecular cleavage steps that emanate from isolated screw dislocations in crystals.

Jan 1, 1959

By J. L. Jones

1. Brinell tests at progressively increasing temperatures are given for a representative lead-base and a representative tin-base babbitt, showing that the former has superior resistance to deformation at the working temperatures of bearings. 2. Small squares of bearing bronze, tinned and then babbitted with a representative lead-base babbitt and a representative tin-base babbitt were subjected to compressive loading. The lead-base babbitt showed less average compression than the tin-base babbitt. Compression did not materially increase the Brinell hardness of the babbitts. 3. A process and a tool are described for giving smoother and more accurate surfaces to bearings than has heretofore been possible. The following experiments have recently been carried out in the chemical laboratory of the Westinghouse Electric and Manufacturing Co., Pittsburgh, Pa. While the work is incomplete, it is described at the present time because data on the comparative merits of lead-base and tin-base babbitts are of interest in connection with the present shortage of tin. BRinell Habdness of Babbitt at Increasing Temperatures Bearings fail because of wiping, or deformation. Hence tenacity is desirable in a bearing metal, especially tenacity at high temperatures. The Brinell test is commonly regarded as a measure of tenacity. In fact, it has recently been proposed to substitute for Brinell hardness number the expression " tenacity number."l It seemed, therefore, that the Brinell test was especially adapted for the tests described. Disks, 4 in. (101 mm.) in diameter and 1.5 in. (38 mm.) thick, were made of the babbitts to be studied, designated A, B, C. They were poured into metal molds, pyrometer leads being soldered in the center of each disk. The composition of the babbitts was as follows:

Jan 1, 1919

By F. R. Hewitt

THE methods of mining talc are simple, and in western North Carolina are almost entirely by open cut and quarry. The larger part of the talc of this section lies in various-sized "veins" inclosed in quartzitic walls, the majority of which have by folding been thrown into a perpendicular position, or nearly so, and the exposed edges of which have been covered by debris from erosion of the mountain above. This covering of loose rocks and earth is from 5 to 25 ft. thick, and in most cases has to be removed because it is difficult to support. Sometimes the covering is heavy enough to "catch" and timber successfully, and in this case the talc can be worked out by the usual method of following the "vein," using stulls for holding up the walls until the vein is worked out, and then allowing the cut or drift to fall in. In some cases it proves more convenient to sink shafts and run drifts, following the talc "veins" until exhausted. The talc deposits of this section are badly broken and faulted both laterally and perpendicularly, and in some cases are found many feet below the level of drainage, necessitating pumping at considerable expense. . My own experience in mining talc has been that the chief point is to get a reliable "vein," and that then the mining is not as difficult, or any more so at least, than that of any common ore. If the. "veins" are pure talc it is simple; if the talc is admixed with foreign matter, such as tremolite in excess, or stains of iron or manganese, as is often the case, one had better abandon the deposit.

Jan 8, 1916

By C. M. Warner

In both the Flat River district of southeast Missouri and the Joplin district of southwest Missouri the lead concentrates are of very high grade, free of arsenic, antimony and bismuth, and contain no gold and very little silver. The general practice in both districts is to smelt the concentrates containing 70 to 85 per cent lead on Scotch hearths, to recover 70 to 85 per cent of the lead, and then smelt in a blast furnace the slag formed in the Scotch hearths to bring the total recovery of lead from lead concentrates to over 97.5 per cent. At the lead smelter of the St. Joseph Lead Co. at Herculaneum, Mo., no Scotch hearths are used. In the other smelters in the district the blast furnace plays a minor role to the Scotch hearth . The concentrates produced from the Flat River district are either table concentrates or flotation concentrates containing: Both types of concentrates are received at Herculaneum in box cars after being sampled. Great care is taken in weighing and sampling of cars of concentrates and in the determination of moisture and lead contents. The concentrates are unloaded into bins by an adaptation of scoop grain unloader. Four men unload and sweep a 40 to 45-ton box car of concentrates in 30 minutes. The same grade of concentrates is received each day and no metal-bearing fluxes are available. The problem is to get as high a recovery as possible as cheaply as possible from the high-grade lead concentrates produced by the company's concentrating mills. Sintering The bulk of the sulphur is removed from the concentrates and the fine concentrate particles are agglomerated by double roasting on typical Dwight and Lloyd sintering machines.

Jan 1, 1937